Data Cabling and Connectivity Solutions Wall-mount/Open rack shall be used on the floor ... Standard...
Transcript of Data Cabling and Connectivity Solutions Wall-mount/Open rack shall be used on the floor ... Standard...
a
Data Cabling and Connectivity Solutions
Make the most of your energyWorld energy consumption has risen 45% since 1980 and it is projected to be 70% higher by 2030. To limit energy cost and its impact on the environment, we must learn to adapt and manage energy consumption, costs and pollutants. Schneider Electric is committed to reducing the energy cost and CO2 emission of its customers.
Our products, solutions and services are present at every link in the energy value chain for the building, infrastructure, industry and residential market to ensure your comfort and performance, while taking into account environmental issues.
This brochure was printed at Blue Star Group (NZ) Ltd, who are FSC® Chain of Custody certified, using FSC Chain of Custody paper. FSC (Forest Stewardship Council) is an international, not-for-profit membership-based organisation that brings people together to find solutions to problems created by bad forestry practices and to reward good management. The FSC Chain of Custody is the highest and most trustworthy international certification for paper and timber products. This catalogue was manufactured using mineral oil free ink (produced with renewable resources, unlike traditional mineral oil based inks). The mill where the paper is manufactured is ISO 14001, the paper is Elemental Chlorine Free (ECF) and the pulp is Mixed Sources FSC certified.
FSC Logo to be updated at
time of print
1
Datacomms Category Classifications
The table below shows supported protocols, bandwidth, maximum transmission rates and recommended use for all categories.
CAT 3 CAT 5/5E CAT 6 CAT 6A CAT 7 CAT 7AClass classification
Class B Class D Class E Class EAClass F Class FA
Supported protocols
Analog, Voice, ISDN, 10Base-T
1000Base-T and lower
1000Base-TX and lower
10GBase-T and lower
10GBase-T and lower
10GBase-T and lower
Bandwidth 16MHz 100MHz 200MHz/250MHz 500MHz 600MHz 1,000MHz
Maximum transmission rate
10Mbps 1,000Mbps (Gigabit Ethernet)
1,000Mbps (Gigabit Ethernet)
10Gbps 10Gbps and beyond
10Gbps and beyond
Usability Predominantly telephone distribution systems.
Regular data and voice traffic.
Higher data traffic (multimedia, streaming).
High data traffic, backbone distribution systems, SAN.
High data traffic, backbone distribution systems, SAN.
High data traffic, backbone distribution systems, SAN.
actassi Category 7a GG45 4
actassi Category 6a 10G 14
actassi Category 6 & 5e 22
actassi Cabling 28
actassi 70 Installation Trunking 32
actassi Fibre 44
CONTENTS
Actassi Product Overview Catalogue2
Actassi technological achievement, making technology work for you.
Data CentreCustomer expectations• Stability: security for installations and data• Flexibility & easy maintenance: infrastructures
modularity; fast data centre construction, evolution and maintenance
• New technologies adoption: adaptation to fast changing telecom technologies and market conditions
Proposed solutions• Cat 7A GG45 high bandwidth capacity of 1000MHz• 10G/Cat 7A solution is recommended for future
network upgrade
Office BuildingCustomer expectations• Flexibility: reserved open area for future tenants
work station expansion or re-arrangement• Network Complexity: requirements for different
application network physically separated• Superior performance: sufficient performance
headroom for future network upgrade
Proposed solutions• Raised floor or ceiling cabling design for flexible cabling• 10G/Cat 6A or Cat 6 application is recommended
for future network upgrade possibility
3
HotelCustomer expectations• Network complexity: requirements for different
application network upon different locations inside of the hotels
• High-density application: limited distribution room space
• Easy maintenance and fast recovery: all maintenance and urgent repair shall not have negative impact on the guests
• Design in line with the overall decoration style of the hotel: especially in the guest rooms
Proposed solutions• Cat 6 application is recommended for guest room and
office area• Floor sockets are widely used in open areas, e.g. lobby,
banquet hall• Wall-mount/Open rack shall be used on the floor
distribution to minimise the space
Health CareCustomer expectations• Stability and reliability: hospitals can’t afford network
breakdown, especially related to medical treatment equipment
• Prevent EMC interference between the network and treatment equipments
• Large volume of data transmission in particular areas, such as ICU, operation room…
• Need to consider layout of the facility; several buildings in one facility
Proposed solutions• Cat 6 solution for reliable performance – proven records• 10G/Cat 6a solution is recommended for large data
transmission areas• Cat 6 application can be considered as an ideal
solution for a network where critical equipment is located
Actassi Product Overview Catalogue4
Actassi Category 7A GG45 Solution
5
Actassi Category 7A GG45
Technology waits for no business and in the Data Communications industry, there’s a need for supported infrastructure to evolve with it. A solution is required to fulfil the needs of today, and also for years to come. Schneider Electric’s Actassi Category 7A GG45 can do it all...
A common problem for any organisation is the need to access more bandwidth. The Cat 7A GG45 high bandwidth capacity of 1000MHz can support the requirements of 10 gigabits per second and beyond; filling this need for more bandwidth. This will prove to be more than a mere luxury — it will become a necessity when looking for longevity in a structured cabling solution for organisations in Australia and New Zealand.
Schneider Electric’s Actassi Category 7A GG45 copper solution design is backward compatible. Standard RJ45 patch cords allow you to use the most current Ethernet protocol available. You can then upgrade to the GG45 patch cord in the future, as your business equipment becomes more advanced and able to process information at much faster speeds.
The Cat 7A solution also overcomes expansion and building upgrade issues, for any pivotal business. Downtime is near impossible and infrastructure replacement cost far too high for critical applications such as hospitals, airports and banks, which rely on high bandwidth. By installing this versatile Cat 7A cable in new buildings and refurbished wings, Australian and New Zealand businesses will ensure minimal time is lost upgrading in the future. Schneider Electric is offering exclusive access to the Actassi Category 7A GG45, to enable a seamless transition as new technology becomes available.
The Category 7A GG45 solution comprises:
• Components defined in ISO/IEC 11801 A2 to meet the performance requirements for Class FA (or Augmented Class F).
• Shielded 24-port unloaded patch panels (straight and angled) give you flexibility on any application. Both come with mounting hardware.
• The shielded 1,000MHz, 12-contact connector is backwards compatible; capable of performing in line with all Category 6A parameters and below, and has a transmission performance of 1Gb–10Gbs. The GG45 connector has an RJ45 footprint (eight contacts across the top) and the additional four contacts on the bottom, create the full Cat 7A interface. For Category 7A parameters, contacts three–six (at the top of the connector) are grounded by the activation of the switch at the rear. This isolates two contacts in each corner of the connector, reducing interference and allowing a transmission performance of beyond 10Gbs.
• Both the 4-pair S/FTP cable and the 4-pair S/FTP patch cord, have a braided shield and four individually screened pairs, to provide superior performance up to 1,000MHz and with no issues of alien crosstalk. The plug is designed to keep the separation of the pairs all the way through to the equipment.
Actassi Product Overview Catalogue6
Category 7A Cable
Cable
The Actassi Category 7A GG45 Cable can easily be identifed by its orange low smoke zero halogen (LS0H) cable jacketing, which comes standard. This 4-pair S/FTP cable has individually screened pairs and is fully compliant to the latest ISO/IEC 611801 and ISP/IEC 61156-6 Standards. It will perform up to 1,000MHz and headroom also exceeds Category 7A requirements.
With superior electrical performance and characteristics to match, the Cat 7A cable offers full immunity against alien crosstalk (AXT) and is suitable for transmission requirements of up to10Gbs and more.
The cable has been designed for maximum output when used with the Actassi Category 7A GG45 Connector.
2D4P7ALSF3R-OR
Frequency (MHz)
Insertion Loss (dB/100m)
Return Loss (dB)
NEXT (dB) PS NEXT (dB)
ACRF (dB) PS ACRF (dB)
PS ANEXT (dB)
PS AACRF (dB)
Max. Min. Min. Min. Min. Min. Min. Min.
4 3.7 23.0 78.0 75.0 78.0 75.0 67.0 67.0
10 5.8 25.0 78.0 75.0 75.3 72.3 67.0 67.0
16 7.3 25.0 78.0 75.0 71.2 68.2 67.0 67.0
20 8.2 25.0 78.0 75.0 69.3 66.3 67.0 67.0
31.25 10.3 23.6 78.0 75.0 65.4 62.4 67.0 63.3
62.5 14.6 21.5 78.0 75.0 59.4 56.4 67.0 57.3
100 18.5 20.1 75.4 72.4 55.3 52.3 67.0 53.2
125 20.8 19.4 73.9 70.9 53.4 50.4 67.0 51.3
200 26.5 18.0 70.9 67.9 49.3 46.3 67.0 47.2
250 29.7 17.3 69.4 66.4 47.3 44.3 67.0 45.2
300 32.7 17.3 68.2 65.2 45.8 42.8 67.0 43.7
400 38.0 17.3 66.4 63.4 43.3 40.3 67.0 41.2
500 42.8 17.3 64.9 61.9 41.3 38.3 67.0 39.2
600.0 47.1 17.3 63.7 60.7 39.7 36.7 65.8 37.6
1000.0 61.9 15.1 60.4 57.4 35.3 32.3 62.5 33.2
7
Outer sheathConductor: copper
Insulation: cellular-PEElement screen
4-Pair
Braid
Specifications
Rated Temperature 60˚C
Flammability Test LSZH DEL 60332-1
Application Horizontal wiring in LAN
Reference Standard IEC61156-5
NVP 80%
Catalogue No. Description
2D4P7ALSF3R-OR Cable LAN Category 7A SFTP LSZH 305m Reel, orange
Mechanical Characteristics
Test Object Jacket
Test Material LSZH
Sheath Tensile Strength ≥9MPa
Bend radius: During Installation After Installed
80mm 40mm
Pulling Tension 210N (47lbf)
Storage Temp -20˚C to 60˚C
Installation Temp 0˚C to 50˚C
Operation Temp -20˚C to 60˚C
Construction
Conductor Solid bare copper
AWG 23
Insulation Cellular PE
Insulated Wire Diameter < 1.45mm
Jacket LSZH
Outer Diameter 7.7mm
Element/Overall Screen Aluminium bonded poly tape/Tinned copper braid
Electrical Characteristics
Characteristic Impedance 100 ± 5Ω
Delay Skew ≤45ns/100m
Propogation delay max @ 100mHz
≤536ns/100m
Max. Conductor d.c. Resistance 20˚C
80Ohms/km
Actassi Product Overview Catalogue8
24-Port Patch Panel
The Actassi Unloaded 7A 1RU 24-Port 19 Inch Rack Mountable Shielded Patch Panel meets the highest standards in both performance and functionality. The panel comes in two options:
RJ24USPP
A conventional straight panel, which offers you all the superior features and benefits that the market has come to expect from Schneider Electric’s high-calibre patch panel range. For use in the Category 7A solution, the patch panel is purchased unloaded and connectors are purchased separately. This provides the flexibility to configure as the user requires. Each panel comes with the rear cable manager and all the necessary mounting hardware.
RJ24USPPAN
This is the latest addition to the Patch Panel range. This 24-port angled panel comes with all the standard features and benefits of a market-leading angled patch panel, including the ability to route cables directly into the vertical cable managers (eliminating the need for horizontal cable management between panels). Once coupled with a Category 7A GG45 connector, no other solution in the market comes close to the Actassi Category 7A solution. Utilising the angled patch panel can save on overall installation costs and it preserves space on the rack, and bend radius on the patch cords. For use in the Category 7A solution, the angled patch panel is purchased unloaded and connectors are purchased separately. This provides the flexibility to configure as the user requires. Each panel comes with all the necessary mounting hardware.
Features and benefits
• Nickle-plated and powder-coated frame with Earthing point.
• Robust powder-coated panels for longevity.
• Connectors are required to be purchased separately for flexibility.
• Universal colour coding to meet 568A or 568B Standards.
• Removable rear cable management tray (straight panel).
• Angled panel provides high density within your rack and removes the requirement for horizontal management.
• Comes complete with all necessary mounting and cable fixing hardware.
Catalogue No. Description
RJ24USPP Patch Panel 24-Port Shielded Unloaded
RJ24USPPAN Patch Panel Angled 24-Port Shielded Unloaded
RJ24USPP
RJ24USPPAN
A
B
C
B
C
A
Category 7A GG45 24-Port Patch Panel
Dimensions
Product A B C
RJ24USPP 44mm 482mm 124mm
RJ24USPPAN 44mm 482mm 140mm
9
Modular Connectors
The Actassi Category 7A GG45 is a shielded, 12-contact, standardised, high-speed connector that's also backwards compatible; capable of performing in line with Cat 6A, Cat 6 and Cat 5e parameters. When using a conventional RJ45 patch cord, the RJ45 service becomes available by bringing the upper eight contacts on the RJ45 connector, into operation. This provides the user with transmission performance of 1Gb–10GBs (an operational bandwidth of 100MHz–500MHz).
For performance above what an RJ45 configuration can deliver, the GG45 patch cord is used. The additional contacts in the GG45 12-contact patch cord (eight contacts on the top and four contacts in the bottom) create the full Cat 7A interface required for 1,000MHz tranmission. The connector and GG45 patch cord, create a high performance solution using all eight corner contacts (two in each corner of the connector). The depression of an internal switch, located in the centre of the connector, grounds contacts three–six and isolates two contacts per corner. Without risk of interference or AXT, transmission performance of beyond 10GBs can be achieved.
Connectors are available for solid and stranded cable, where a consolidation point is used. All connectors are keystone connectors, with a 30 Mech adaptor provided as standard.
Features and benefits
• Fully compliant to ISO/IEC 11801 Standards – "Connecting Hardware Requirements to Category 7A".
• Fully backwards compatible to Cat 6A, Cat 6 and Cat 5e parameters.
• 360º screened for full protection against AXT.
• Compression type termination.
• Full terminating instructions.
• Stranded version for consolidation point or cross connect applications.
Catalogue No. Description
GG45SM7ASSD Cat 7A GG45 Connector K/ST Shielded Solid
GG45SM7ASST Cat 7A GG45 Connector K/ST Shielded Stranded
GG45SM7ASSD
Category 7A GG45 Connectors
Dimensions
Product A B C
GG45SM7ASSD 16mm 14mm 45mm
GG45SM7ASST 16mm 14mm 45mm
A
CB
Actassi Product Overview Catalogue10
Category 7A GG45 Patch cord
Patch Cord
The Actassi Category 7A GG45 Patch Cord is constructed as a 4-Pair S/FTP cable, with individually screened pairs and an overall braid, offered in orange low smoke zero halogen (LS0H) cable jacketing as the standard offer.
The GG45 patch cord design maximises the full performance of the channel, with pair separation all the way through to the plug. The uniquely designed plug has a switch activator, which triggers the grounding of contacts three–six of the GG45 connector. By using the eight extreme corner contacts on the connector, a bandwidth of 1,000Mhz and transmission of beyond 10GBs can be achieved.
Features and benefits
• High bandwidth patch cord for 40GB applications.
• Complies with Class F and Class FA ISO 11801 Standards.
• Self-latching, high reliability GG45 screened plugs.
• Strain-relief boot.
• Orange low smoke zero halogen (LS0H) sheath as standard.
Catalogue No. Description
7AS10LPL-OR Cat 7A GG45 P/Cord LSZH SFTP 1m - Or
7AS20LPL-OR Cat 7A GG45 P/Cord LSZH SFTP 2m - Or
7AS30LPL-OR Cat 7A GG45 P/Cord LSZH SFTP 3m - Or
7AS50LPL-OR Cat 7A GG45 P/Cord LSZH SFTP 5m - Or
7AS100LPL-OR Cat 7A GG45 P/Cord LSZH SFTP 10m - Or
7AS200LPL-OR Cat 7A GG45 P/Cord LSZH SFTP 20m - Or
7AS10LPL-OR
11
Category 7A Termination/Stripping Tools Termination/Stripping Tools
To assist with installation of the Category 7A solution, Actassi offers a S/FTP cable-stripping tool, used to prepare the termination of a cable in an efficient, consistent and precise manner.
Along with the stripping tool, comes a compression termination tool. It provides even pressure around the IDCs, to ensure a secure termination.
Catalogue No. Description
SFTPST SFTP Stripping Tool
GG45TT Comfort Termination ToolSFTPST
GG45TT
Actassi Product Overview Catalogue12
How it works
The GG45 connector is a two-in-one switched connector. The two modes of operation are:
• normal “RJ” mode
• high-speed (switch activated) “GG” mode.
When using the RJ45 patch cords (Cat 6A, Cat 6 or Cat 5e), the connector can be used in RJ mode – as you would for a Cat 6A, Cat 6 or Cat 5e installation. This will perform to the highest Category of the patch cord used.
When the GG mode is required in the future, a GG45 patch cord will be used (see fig. 2). The GG45 patch cord has the unique switch activator, designed as part of the patch cord. The switch activator is located on the tip of the plug (highlighted in blue on fig. 2), and the pair contact points are located on top and bottom of the plug.
When inserted into a GG45 connector, the switch in the connector is activated (highlighted in blue on fig.1). This grounds the four middle contacts to eliminate any interference to the transmission signal, and leaves only the four extreme outer-corner contacts active (highlighted in blue on fig. 3).
High-frequency performance is dependant on pair isolation. This is achieved by combining the GG45 connector with the GG45 patch cord.
Cabinet End
Cat 7A S/FTP Horizontal Cabling
Field End
Fig. 1
Cat 7A Switch (highlighted in blue).
13
GG45 activation (active contacts are highlighted in blue).
For 1GB–10GBs capabilities, use a standard RJ45 Cat 6 or Cat 6A patch cord.
Cat 7A Switch Activator (highlighted in blue).
Fig. 2
Fig. 3
Active Equipment
Field Equipment
Actassi Product Overview Catalogue14
Actassi Category 6A 10G Solution
15
Jack
Separator X
Twisted-Pair
Drain Wire
2D4P6AIPV3R-BU
Category 6A UTP
Actassi 4-Pair Category 6A UTP cable delivers excellent network performance when used in conjunction with other Actassi Category 6A products.
The Category 6A UTP cable consists of 4-pairs of solid insulated copper 23 AWG (0.59mm) and is UL listed with a CM fire rating. It is designed for use in horizontal cabling situations and supplied in 305m (1,000ft) lengths. The Category 6A UTP cable provides a significant margin above the minimum Category 6A near end crosstalk (NEXT) requirement of TIA/EIA 568-B.3-1 and ISO/IEC 11801.
PHYSICaL SPECIFICaTIONSRated Temperature (˚C) 75
Product Standard Certification UL File E197794
Flammability Test CM
Application Horizontal wiring in LAN
Reference Standard ELA/TLA568 and ISO/IEC 11801, IEC61156-5
NVP % 65
CONSTRUCTIONConductor Solid bare copper
AWG 23
Conductor Diameter Nom. (mm) 0.59
Insulation PE
Average Thickness (mm) 0.27
Min. Point Thickness (mm) 0.18
Insulation Diameter (±0.10mm) 1.15
Filler PE
Jacket PVC
Ripcord yes
Outer Diameter (mm) 8.5
MECHaNICaL CHaRaCTERISTICSTest Object Jacket
Test Material PVC
Before Tensile Strength (kg/mm2) >_ 1.05
Bend Radius (mm)Installed 75
After Installed 40
Pulling Tension 110N (25lbf)
Storage Temp (degree Celsius) - 20 to 750
Operating Temp (degree Celsius) - 20 to 750
Installation Temp (degree Celsius) 0-580
Frequency(MHz)
Attenuation(DB/100m)
NEXT(DB)
PSNEXT(DB)
PSNEXT(DB/100m)
PSELFEXT(DB/100m) RL Delay PSANEXT PSAACRF
1 2.1 74.3 72.3 67.8 64.8 20 570 67 674 3.8 65.3 63.3 55.8 52.8 23 552 67 66.28 5.3 60.8 58.8 49.7 46.7 24.5 547 67 60.1
10 5.9 59.3 57.3 47.8 44.8 25 545 67 58.216 7.5 56.2 54.2 43.7 40.7 25 543 67 54.120 8.4 54.8 52.8 41.8 38.8 25 542 67 52.225 9.4 53.3 51.3 39.8 36.8 24.3 541 67 50.2
31.25 10.5 51.9 49.9 37.9 34.9 23.6 540 67 48.362.5 15 47.4 45.4 31.9 28.9 21.5 539 65.6 42.3100 19.1 44.3 42.3 27.8 24.8 20.1 538 62.5 38.2200 27.6 39.8 37.8 21.8 18.8 18 567 58 32.2250 31.1 38.8 36.6 19.8 16.8 17.3 536 56.5 30.2300 34.3 37.1 35.1 18.3 15.3 16.8 536 55.3 28.7400 40.1 35.3 35.1 15.8 12.8 15.9 536 53.5 26.2500 45.3 33.8 31.8 13.8 10.8 15.2 536 52 24.2
Actassi Product Overview Catalogue16
Category 6A UTP Patch Panels 24-Port
Patch panels feature individual Category 6A modular jacks that are colour coded for both 568A and 568B standards. This patch panel is loaded with 24-mechs.
This patch panel should be terminated using the 110 tool.
ELECTRICaL CHaRaCTERISTICSDielectric Strength 1,000v rms at 60Hz for 1 minute
Current Rating 1.5a maximum
Insulation Resistance 200mΩ minimum
Contact Resistance 1mΩ per contact
Temperature Range -40˚c to +70˚c
Transmission Performance ISO/IEC 11801 class Ea AS/NZS 3080:2003 class Ea
MECHaNICaL CHaRaCTERISTICSModular ConnectorRJ45 8-Pin Connector Fcc part 68, subpart F and IEc-60603-7
compliant
Durability 1000 mating cycles
Material phosphor bronze with 50 micro-inches of gold over 100 micro-inches nickel plating
IDC ConnectorIDC Connector suitable insulation of 22 to 24 aWG
(0.64 to 0.41mm)
Insulation Diameter (Wire) 0.70 – 1.40mm
Durability 10 insertions of any combination of wire gauge (2 wires per slot)
Connector Material phosphor bronze with nickel plating
IDC Body and Cover Material Fire-retardant, ul 94v-0, plastic
DIMENSIONS Product A B C
RJ6AU/24PP 44mm 482mm 124mm
PRODUCT FEaTURES• Fully compliant to AS/NZS 3080, ISO/IEC
11801, and ANSI/TIA/EIA-568-B Series Connecting Hardware Standards.
• Powder-coated metal framework.• Universal colour coding for 568A and 568B
Standards.• Removable rear cable management tray.• Compatible with standard 19" equipment
frames.• Individual removable modular jacks.• Staggered design to eliminate ANXT.• Additional label refill sheets can be
purchased separately, RJ6AU/24PPLS. Label printing software can be downloaded from clipsal.com/trade/downloads/software. This will enable you to print the labels onto the template.
CUSTOMER BENEFITS • Complete with all mounting and cable fixing
hardware.• Rear cable management tray is supplied
loose, allowing the installer to fit after termination.
• The front labelling system provides a clear and efficient means of identifying circuits.
• Powder coated metal frame is robust and protects the patch panel from corrosion and scratching.
• Compliance with international standards gives the customer peace of mind that their network will perform to link, channel and application requirements.
RJ6AU/24PP
17
VDIB1773XUWE
Actassi Cat 6A UTP Jacks
Actassi Cat 6A jacks are colour coded for both 568A and 568B standards. Clear wire retaining caps are supplied and should be used to provide additional cable strain relief. This modular connector is designed to be terminated using a 110 tool.
ELECTRICaL CHaRaCTERISTICSDielectric Strength 1,000v rms at 60Hz for 1 minute
Current Rating 1.5a maximum
Insulation Resistance 200mΩ minimum
Contact Resistance 1mΩ per contact
Temperature Range -40˚c to +70˚c
Transmission Performance ISO/IEC 11801 class EA AS/NZS 3080:2003 class Ea
MECHaNICaL CHaRaCTERITICSModular ConnectorRJ45 8-Pin Connector Fcc part 68, subpart F and IEc-60603-7
compliant
Durability 750 insertion cycles minimum
Material phosphor bronze with 50 micro-inches of gold over 100 micro-inches nickel plating
IDC ConnectorIDC Connector suitable insulation of 22 to 24 aWG
(0.64 to 0.41mm)
Insulation Diameter (Wire) 0.70 – 1.60mm
Connector Material phosphor bronze with nickel plating
IDC Body and Cover Material Fire-retardant ul 94v-0, plastic
PRODUCT FEaTURES • Fully compliant to AS/NZS 3080, ISO/IEC
11801, and ANSI/TIA/EIA-568-C Series.• Backward compatible with Category 5e and
Category 6 products.• Flexible locking tabs.• UL 940-0 rated.• Accepts solid 22 - 24 AWG diameter
conductors.• Copper shielded shutter cap to eliminate
alien crosstalk associated with Category 6A.
• Retaining cap supplied for added cable strain relief.
CUSTOMER BENEFITS• Can be used in Multi-User
Telecommunication Outlet applications (MUTO) and Consolidation Points (CP).
• Clear insulation displacement connector caps allow for termination verification and assist in cable retention.
CATALOGUE NUMBER DESCRIPTIONVDIB1775XUWE Connector RJ45 Category 6A. Suits Clipsal 30 Series wall plates.VDIB1773XUWE Connector RJ45 Category 6A. Suits Clipsal 30 Series wall plates – shutteredVDIB1774XUWE Connector RJ45 Category 6A. Keystone ShutteredVDIB1176XUWE Connector RJ45 Category 6A. Keystone
Actassi Product Overview Catalogue18
Category 6A FTP Cable
CATALOGUE NUMBER DESCRIPTIONCPL2D4P6ALSF3R-BU Category 6A FTP Cable LSZH
Actassi 4-Pair Category 6A F/UTP Cable delivers excellent network performance when used in conjunction with Actassi Category 6A FTP products. The cable consists of four pairs of solid insulated copper 23 AWG (0.59mm) with an overall aluminium foil. With the sheath being LSZH classified it provides extra precautions against harmful emissions coming from the sheath in the event of a fire. It is designed for use in horizontal cabling, provides best immunity against external noise interference, and is supplied on a reel in 305m (1,000ft) lengths.
The cable provides a significant margin above the minimum Category 6A near end crosstalk (NEXT) requirement of TIA/EIA 568-B.3-1 and ISO/IEC 11801.
ELECTRICaL PERFORMaNCE
Frequency (MHz)
Attenuation DB/100m
NEXT (DB)
PSNEXT (DB)
PSNEXT (DB/100m)
PSELFEXT (DB/100m)
RL Delay PSANEXT PSAACRF
1 2.1 74.3 72.3 67.8 64.8 20 570 67 674 3.8 65.3 63.3 55.8 52.8 23 552 67 66.28 5.3 60.8 58.8 49.7 46.7 24.5 547 67 60.1
10 5.9 59.3 57.3 47.8 44.8 25 545 67 58.216 7.5 56.2 54.2 43.7 40.7 25 543 67 54.120 8.4 54.8 52.8 41.8 38.8 25 542 67 52.225 9.4 53.3 51.3 39.8 36.8 24.3 541 67 50.2
31.25 10.5 51.9 49.9 37.9 34.9 23.6 540 67 48.362.5 15 47.4 45.4 31.9 28.9 21.5 539 65.6 42.3100 19.1 44.3 42.3 27.8 24.8 20.1 538 62.5 38.2200 27.6 39.8 37.8 21.8 18.8 18 567 58 32.2250 31.1 38.8 36.6 19.8 16.8 17.3 536 56.5 30.2300 34.3 37.1 35.1 18.3 15.3 16.8 536 55.3 28.7400 40.1 35.3 35.1 15.8 12.8 15.9 536 53.5 26.2
SPECIFICaTIONS
NVP 67%
Rated Temperature 75˚C
Product Standard Certification Delta File 2010-44
Application Horizontal wiring in LAN
Reference Standard IEC61156-5
Flammability Test LSZH DEL 60332-1
ELECTRICaL CHaRaCTERISTICS
Characteristic Impedance 100 ± 5Ω
Delay Skew ≤45ns/100m
Propogation delay – max @ 100mHz ≤536ns/100m
Max. Conductor d.c. – Resistance 20˚C 80Ohms/km
MECHaNICaL CHaRaCTERISTICS
Test Object Test Material LSZH Jacket
Sheath Tensile Strength ≥9MPa
Bend radius:During InstallationAfter Installed
80mm40mm
Pulling Tension 110N (25lbf)
Storage Temp -20˚C to 50˚C
Installation Temp 0˚C to 50˚C
CONSTRUCTION
Conductor Solid bare copper
AWG 23
Insulation PE
Insulated Wire Diameter 1.15 ± 0.10mm
Filler PE
Jacket LSZH
Drain Wire 0.4mm
Outer Diameter 7.3mm
Overall Screen Aluminium bonded poly tape
19
ACTPP6ATGS24NSS
The Actassi 10G Cat 6A FTP 24-Ports Patch Panel is fully loaded with Category 6A Fully Shielded Keystone Modular Jacks. Panel is of a metal frame construction with ABS fascia, bracket and bundle with a rear cable management bar. The panel is powder coated for protection against scratches and rust. The rear cable management bar will ensure a neat cable installation as well as strain relief.
TRaNSMISSION PERFORMaNCEMeet 10G Channel performance requirements specified in TIA/EIA-568-B-2.10 Category 6A and ISO/IEC Class Ea
ENVIRONMENTaL CONDITIONSTemperature RangeStorage -20 to +60˚C
Operational -10 to +50 ˚C
Relative Humidity (Operational) Maximum Non-condensing 93%
ELECTRICaL CHaRaCTERISTICSModular ConnectorElectrical Insulation Resistance 10 Mega ohms Minimum
Dielectric Withstanding Voltage 1,000V RMS at 60HZ for 1 Minute
Contact Resistance 20 Milliohms Maximum
Current Ratings 1.5 AMPS at 20˚C
MECHaNICaL CHaRaCTERISTICSModular ConnectorTotal Mating Force 800 Grams for a 8 Wire Leads Minimum
Retention 30 Lbs Min between the Jack and Plug
Insertion/Extraction Life 750 Cycles Minimum
Number of IDC Termination 200 Minimum
DIMENSIONSShipping Box 510mm(L) x 80mm(H) x 135mm(D)
Shipping Weight 1.5kg
PRODUCT FEaTURES• Category 6A Fully Shielded Keystone
Modular Jacks• Universal colour-coding for 568A and 568B
standards• Front labelling system• Removable rear cable management bar is
bundled with Velcro tapes• Compatible with standard 19" equipment
racks• Fully compliant ISO/IEC11801 Edition 2
2002 and ANSI/TIA/EIA-568-B Series Connecting Hardware Standards
CUSTOMER BENEFITS• Modular jacks are individually removable
and replaceable• Complete kit with all mounting and cable
fixing hardware• Label holders for easy labelling and
identification• Cable management bar provides neat
installation and strain relief• Compliance with international standards
gives the customer peace of mind that their network will perform to link, channel and application requirements
10G Cat 6A FTP 24-Port Patch Panel
CATALOGUE NUMBER DESCRIPTIONACTPP6ATGS24NSS 10G Cat 6A FTP 24-port Patch Panel, loadedACTPP6ATGS24NSU 10G Cat 6A FTP 24-port Patch Panel, unloaded
Actassi Product Overview Catalogue20
ACTRJSMTG6ANSS
The Actassi 10G Cat 6A Fully Shielded Modular Jack is a Keystone information outlet which is developed primarily for use of high speed 10G LAN applications. The newly designed toolless modular jack provides no punch down tool for termination. Fully shielded jack eliminates Alien Crosstalk (ANEXT) and delivers the best network performance when used in conjunction with other Actassi 10G products.
TRaNSMISSION PERFORMaNCEMeet 10G Channel performance requirements specified in TIA/EIA-568-B.2-10 Category 6A and ISO/IEC 11801 Class Ea
PHYSICaL SPECIFICaTIONSHousing Zinc-alloy fully shielded
Spring Wire Phosphor Bronze Alloy Plated with 50µ" of Gold over 70~100 µ" of Nickel
IDC Phosphor Bronze Alloy with 100 µ" Tin, Planted with 100% Tin Mistiness
ELECTRICaL CHaRaCTERISTICSInsulation Resistance 500MΩ Min. @ 100V DC
Dielectric Withstanding Voltage 1000V DC/AC @ 60Hz for 1 minute
Spring Wire Contact Resistance 20mΩ Max.
IDC Contact Resistance 2.5mΩ Max.
MECHaNICaL CHaRaCTERISTICSTotal Mating Force 800g for a 8 Wire Leads Min.
Retention 50N (11 Lbs) for 60s±5s
Insertion/Extraction Life 750 Cycles Minimum
IDC Wire Gauge 22~24 AWG
ENVIRONMENTaL CONDITIONSTemperature Range - 40 to 70°C
Operation -10 to 60°C
Relative Humidity (Operational) Max. Non-condensing 93%
PaCKaGINGShipping Pack Individual PE Bag
Shipping Weight 35g
PRODUCT FEaTURES• Complies with TIA/EIA-568-B.2-10
Category 6A and ISO/IEC 11801Class Ea Standards
• Newly designed toolless termination• Zinc-alloy fully shielded• Accepts solid or stranded 22-24AWG
conductors• Universal colour coding for 568A and 568B
CUSTOMER BENEFITS• Termination without punch-down tool• Fully shielded eliminating ANEXT• Compatible with Keystone wall plates
10G Cat 6A FTP Modular Jack
CATALOGUE NUMBER DESCRIPTIONACTRJSMTG6ANSS Non-Shutter Modular Jack, Cat 6A 10G FTP Keystone, MetalACTRJSMTG6ANSSP Non-Shutter Modular Jack, Cat 6A 10G FTP Keystone, Metal, for Panel Version (Pkt 24)30RJ45SMA6A-WE Non-Shutter 30M Jack, Cat 6A 10G UTP
21
Notes
Actassi Product Overview Catalogue22
Actassi Connectivity Category 6
Category 5e
23
ACTPP6U24NSS
The Patch Panels are a perfect combination of sleek looks and outstanding performance.
The 24 individual Category 6 Keystone modular jacks incorporate PCB Technology, improving consistency in performance, and exactly matching the work-area outlets. These modular jacks are colour coded for both T568A and T568B wiring scheme and can be terminated using an Actassi or other compatible tools. Clear wire retaining caps are supplied and can be used to provide additional cable strain relief.
The sleek silver fascia of the product comprises three designation-strip holders with a label kit supplied. Velcro cable ties, cage nuts and screws are also provided with the product.
Combined with other Actassi Products, they are the perfect solution to your voice and data communications needs.
ELECTRICaL CHaRaCTERISTICSDielectric Strength 1,000V RMS at 60Hz for 1 minute
Current Rating 1.5Amp maximum
Insulation Resistance 200MΩ minimum
Contact Resistance 1mΩ per contact
Temperature Range -40˚C to +70˚C
Transmission Performance Exceeds ISO/IEC 11801 Class EAS/NZS 3080:2003 Class E
MECHaNICaL CHaRaCTERISTICSModular Connector
RJ45 8-Pin Connector FCC part 68, Subpart F and IEC-60603-7 compliant
Durability 1,000 mating cycles
Material Phosphor bronze with 50 micro-inches of gold over 100 micro-inches nickel plating
IDC Connector
IDC Connector Insulation slicing of 22 to 24AWG (0.64mm to 0.41mm)
Insulation Diameter (Wire) 0.70mm – 1.40mm
Connector Material Phosphor bronze with nickel plating
IDC Body & Cover Material Fire-Retar-dant, UL 94V-0, Plastic
PRODUCT FEaTURES• Aesthetic, contemporary design.• Powder coated metal framework.• Universal colour-coding for T568A and T568B
wiring scheme.• Removable rear cable management tray.• Compatible with standard 19" equipment
frames.• IDC termination using a Actassi or other
compatible tools.• Fully compliant to AS/NZS 3080:2003, ISO/IEC
11801 Edition 2 2002 and ANSI/TIA/EIA-568-B Series Connecting Hardware Standards.
CUSTOMER BENEFITS• Contemporary design will improve the aesthetics
of all installations.• Better than Category 6 Performance.• Complete with all mounting and cable fixing
hardware.• Rear cable management tray is supplied loose,
allowing the installer to fit after termination.• The front labelling system provides a clear and
efficient means of identifying circuits.• Powder coated metal frame is robust and
protects the patch panel from corrosion and scratching.
• Compliance with international standards give customers peace of mind that their network will perform to link, channel and application requirements.
CATALOGUE NUMBER DESCRIPTIONACTPP6U24NSS Category 6 UTP 24-port Non-Shutter Patch Panel, loadedACTPP6U24SHS Category 6 UTP 24-port Shuttered Patch Panel, loaded
Category 6 Patch Panels
Actassi Product Overview Catalogue24
ACTPP5EU24NSS
The Category 5e Patch Panels are a perfect combination of sleek looks and outstanding performance.
They feature 24 individual Category 5e modular jacks that are colour coded for both T568A and T568B wiring scheme and can be terminated using an Actassi or other compatible tools. Clear wire retaining caps are supplied and can be used to provide additional cable strain relief.
The sleek silver face of the product comprises three designation-strip holders with a label kit supplied. Velcro cable ties, cage nuts and screws are also provided with the product.
Combined with other Actassi Products, they are the perfect solution to your voice and data communications needs.
ELECTRICaL CHaRaCTERISTICSDielectric Strength 1,000V RMS at 60Hz for 1 minute
Current Rating 1.5Amp maximum
Insulation Resistance 10MΩ minimum
Contact Resistance 2mΩ per contact
Temperature Range -10˚C to +60˚C
Transmission Performance Exceeds ISO/IEC 11801 Class E AS/NZS 3080:2003 Class E
MECHaNICaL CHaRaCTERISTICSModular Connector
RJ45 8-Pin Connector FCC part 68, Subpart F and IEC-60603-7 compliant
Durability 750 insertion cycles min.
Material Phosphor bronze with 50 micro-inches of gold over 100 micro-inches nickel plating
IDC Connector
IDC Connector Insulation slicing of 22 to 24AWG (0.64mm to 0.41mm)
Insulation Diameter (Wire) 0.70mm – 1.60mm
Connector Material Phosphor bronze with nickel plating
IDC Body & Cover Material Fire-Retardant, UL 94V-0, Plastic
PRODUCT FEaTURES• Aesthetic, contemporary design.• Powder coated metal framework.• Universal colour-coding for T568A and T568B
wiring scheme.• Removable rear cable management tray.• Compatible with standard 19” equipment frames.• IDC termination using an Actassi or other
compatible tools.• Fully compliant to AS/NZS 3080:2003, ISO/IEC
11801 Edition 2 2002 and ANSI/TIA/EIA-568-B Series Connecting Hardware Standards.
CUSTOMER BENEFITS• Contemporary design will improve the aesthetics
of all installations.• Complete with all mounting and cable fixing
hardware.• Rear cable management tray is supplied loose,
allowing the installer to fit after termination.• The front labelling system provides a clear and
efficient means of identifying circuits.• Powder coated metal frame is robust and
protects the patch panel from corrosion and scratching.
• Compliance with international standards give customers peace of mind that their network will perform to link, channel and application requirements.
Category 5e Patch Panels
CATALOGUE NUMBER DESCRIPTIONACTPP5EU24NSS Category 5e UTP 24-port Non-Shutter Patch Panel, loaded
25
VDIB17766UWE VDIB17746UWE VDIB17736UWE
The Actassi range of products are the next generation of data communications solutions.
The Category 6 shuttered modular jacks incorporate patented shutter mechanism. Combine this feature with PCB Technology, and you have the most technically advanced Category 6 connector on the market. These modular jacks are colour-coded for both T568A and T568B wiring scheme and can be terminated using an Actassi or other compatible tool.
Clear wire retaining caps are supplied and can be used to provide additional cable strain relief.
Combined with other Actassi Products, they are the perfect solution to your voice and data communications needs.
ELECTRICaL CHaRaCTERISTICSDielectric Strength 1,000V RMS at 60Hz for 1 minute
Current Rating 1.5Amp maximum
Insulation Resistance 200MΩ minimum
Contact Resistance 1mΩ per contact
Temperature Range -40˚C to +70˚C
Transmission Performance Exceeds ISO/IEC 11801 Class EAS/NZS 3080:2003 Class E
MECHaNICaL CHaRaCTERISTICSModular ConnectorRJ45 8-Pin Connector FCC part 68, Subpart F and IEC-60603-7
compliant
Durability 1,000 mating cycles min.
Material Phosphor bronze with 50 micro-inches of gold over 100 micro-inches nickel plating
IDC Connector
IDC Connector Insulation slicing of 22 to 24AWG (0.64mm to 0.41mm)
Insulation Diameter (Wire) 0.70mm – 1.40mm
Connector Material Phosphor bronze with nickel plating
IDC Body & Cover Material Fire-Retardant, UL 94V-0, Plastic
PRODUCT FEaTURES• Aesthetic, contemporary design.• Patented flush-faced, zero footprint shutter
mechanism.• Fully compliant to AS/NZS 3080:2003, ISO/IEC
11801 Edition 2002 and ANSI/TIA/EIA-568-B Series Connecting Hardware Standards.
• Backward compatible with Category 5 and 5e products.
• Flexible locking tabs (30-Mech connectors).• Compatible with Actassi or other compatible
tools.• UL 94V-0 rated.• Accepts solid 22-24AWG diameter conductors.
CUSTOMER BENEFITS• Performs beyond Category 6 Standards.• Shutter mechanism is easy to operate, simply
insert the plug lead into the jack.• Protection from dust ingress, insect infestation
and the insertion of foreign objects.• Various colours for easier circuit identification.• Backward compatible with Category 5 and 5e
products, allowing component mixing without degrading the network below the minimum component category.
• 30-Mech style fits all Schneider Electric Wall Plates (Australian, US and British), giving the customer access to the most popular plates on the market.
• For use in Multi-user Telecommunication Outlet Applications (MUTO) and Consolidation Points (CP).
• Flexible locking tabs allow for easy removal from Wall Plates (30-Mech).
• Clear IDC caps that allow for termination verification and assist in cable retention.
COLOURS• White Electric (WE), Black (BK)• Red (RD)*, Yellow (YL)* Soft Grey (GY)*, Green
(GR)*
*These colours are indent only and have a minimum order quantity of 280
CATALOGUE NUMBER DESCRIPTION
Category 6 Modular JacksVDIB17766UWE Non-Shutter Modular Jack,Category 6 UTP Keystone, WhiteVDIB17746UWE PlanuShut Modular Jack,Category 6, Keystone, WhiteVDIB17736UWE PlanuShut Modular Jack,Category 6, 30M, WhiteVDIB17756UWE Non-Shutter Modular Jack,Category 6 UTP 30M, White
Category 6 Modular Jacks
Actassi Product Overview Catalogue26
VDIB17745UWE
VDIB17735UWE
The Category 5e modular jacks incorporate patented shutter mechanism. These modular jacks are colour-coded for both T568A and T568B wiring scheme and can be terminated using an Actassi or other compatible tools.
Clear wire retaining caps are supplied and can be used to provide additional cable strain relief.
Combined with other Actassi Products, they are the perfect solution to your voice and data communications needs.
ELECTRICaL CHaRaCTERISTICSDielectric Strength 1,000V RMS at 60Hz for 1 minute
Current Rating 1.5Amp maximum
Insulation Resistance 500MΩ minimum
Contact Resistance 2mΩ per contact
Temperature Range -40˚C to +70˚C
Transmission Performance exceeds ISO/IEC 11801 Class EAS/NZS 3080:2003 Class E
MECHaNICaL CHaRaCTERISTICSModular Connector
RJ45 8-Pin Connector FCC part 68, Subpart F and IEC-60603-7 compliant
Durability 750 insertion cycles min.
Material Phosphor bronze with 50 micro-inches of
gold over 100 micro-inches nickel plating
IDC Connector
IDC Connector Insulation slicing of 22 to 24AWG (0.64mm to 0.41mm)
Insulation Diameter (Wire) 0.70mm – 1.60mm
Connector Material Phosphor bronze with nickel plating
IDC Body & Cover Material Fire-Retardant, UL 94V-0, Plastic
PRODUCT FEaTURES• Aesthetic, contemporary design.• Patented flush-faced, zero footprint shutter
mechanism.• Fully compliant to AS/NZS 3080:2003, ISO/IEC
11801 Edition 2 2002 and ANSI/TIA/EIA-568-B Series Connecting Hardware Standards.
• Flexible locking tabs (30-Mech connectors).• Compatible with Actassi or other compatible
tools.• UL 94V-0 rated.• Accepts solid 22-24AWG diameter conductors.
CUSTOMER BENEFITS• Shutter mechanism is easy to operate, simply
insert the plug lead into the jack.• Protection from dust ingress, insect infestation
and the insertion of foreign objects.• Available in various colours for easier circuit
identification.• 30-Mech style fits all Schneider Electric Wall
Plates (Australian, US and British), giving the customer access to the most popular plates on the market.
• For use in Multi-user Telecommunications Outlet Applications (MUTO) and Consolidation Points (CP).
• Flexible locking tabs allow for easy removal from Wall Plates (30-Mech).
• Clear IDC caps that allow for termination verification and assist in cable retention.
Category 5e Modular Jacks
CATALOGUE NUMBER DESCRIPTION
Category 5e Modular JacksVDIB17735UWE Shutter Modular Jack,Category 5e, 30M, WhiteVDIB17745UWE Shutter Modular Jack,Category 5e, Keystone, WhiteRJ45SMA5-WE Non-Shutter Modular Jack,Category 5e UTP Keystone, White
27
ACTTLQTB
Quick Termination Tool
CATALOGUE NUMBER DESCRIPTIONACTTLQTB Quick Termination Tool – Suits Actassi Cat 5e, Cat 6 & Cat 6AACTTLQTBCM Quick termination tool replacement cutting module
aCTaSSI KEYSTONE DaTa JaCKS PDL KEYSTONE CLIPSItem Code CATEGORY 619MKC 615MKC 815MKC1 815MKC2
VDIB17745U 5e ✗ ✓ ✓ ✓
VDIB17746U 6 ✗ ✓ ✓ ✓
VDIB17766U 6 ✗ ✓ ✓ ✓
VDIB1774XU 6A ✗ ✓ ✓ ✓
VDIB1776XU 6A ✗ ✓ ✓ ✓
RJ45SMA6A 6A ✗ ✓ ✓ ✓
Reference and Compatibility chart for PDL Keystone Clips and Actassi Keystone Data Jacks
PRODUCT FEaTURES• Fast and easy field installation tool.• Simple squeeze handle.• Special base is compatible with Keystone & 30-Mech Jacks.• Replaceable cutting module design.• Handle lock design.
CUSTOMER BENEFITS• Save up termination time over 80%.• Save up termination force needed to 70%.• Termination of all wires at one single squeeze.• Ensure stability and safety during termination.• Provide tools longer life and cost saving.• Easy & handy carrying and storage.
Actassi Product Overview Catalogue28
Actassi Cabling
29
2D4P5IPV3B-BU
Conductor
Insulation
Jacket
Rip Cord
Category 5e UTP PVC CablesThe Actassi Category 5e 4-Pair Cable consists of 24AWG (0.51mm) solid-copper conductors insulated with high-density polyethylene. The insulated conductors are tightly twisted into pairs and covered with PVC material.
The Actassi Category 5e 4-Pair Cable provides excellent high-speed transmission, is certified to 155MHz and supports applications such as 155Mb/s ATM, 622Mb/s ATM and IEEE 802.3 1000 Base-T (Gigabit Ethernet) standard, using parallel transmission technology. This product is UL listed with a CM fire rating.
PHYSICaL SPECIFICaTIONSRated Temperature 75˚C
Product Standard Certification UL
Flammability Test CM
Application Horizontal Wiring in LAN
Reference Standard UL Subject 444, ANSI/TIA/EIA-568B & ISO/IEC 11801
CONSTRUCTIONConductor Solid Bare Copper
AWG 24
Conductor Dia. Nom. (mm) 0.51
Insulation PE
Average Thickness (mm) 0.19
Min. Point Thickness (mm) 0.16
Insulation Diameter (±0.10mm) 0.88
Twisting Lay Length (mm) 30 underneath
Cabling Lay Length (mm) 200 underneath
Jacket PVC
Average Thickness (±0.05mm) 0.50
Min. Point Thickness (mm) 0.43
Outer Diameter (±0.2mm) 4.9
Rip Cord YES
PRODUCT FEaTURES• Complies with Category 5e ANSI/TIA/EIA-568B &
ISO/IEC 11801 Standard.• 24AWG conductors and the transmission is
certified to 100MHz.• UL Listed CM Fire rated.• Exceeds Category 5e ANSI/TIA/EIA-568B and
ISO/IEC 11801 Standards.• Supports transmission of digital and analogue
voice, data and video signal.• Supports Gigabit Ethernet (1000 Base-T).
Category 5e UTP Cables
ELECTRICaL CHaRaCTERISTICSFrequency
(MHz)Return Loss
(dB)Attenuation(dB/100m)
NEXT(dB)
ACR(dB)
PSNEXT(dB)
ELFEXT(dB)
PSELFEXT(dB)
Delay(ns/100m)
0.772 19.4 1.8 67.0 65 64.0 66.0 63.0 575.01 20.0 2.0 65.3 63 62.3 63.8 60.8 570.04 23.0 4.1 56.3 52 53.3 51.7 48.7 552.08 24.5 5.8 51.8 46 48.8 45.7 42.7 546.710 25.0 6.5 50.3 44 47.3 43.8 40.8 545.416 25.0 8.2 47.3 39 44.3 39.7 36.7 543.020 25.0 9.3 45.8 37 42.8 37.7 34.7 542.025 24.3 10.4 44.3 34 41.3 35.8 32.8 541.2
31.25 23.6 11.7 42.9 31 39.9 33.9 30.9 540.462.5 21.5 17.0 38.4 21 35.4 27.8 24.8 538.6100 20.1 22.0 35.3 13 32.3 23.8 20.8 537.6
CATALOGUE NUMBER DESCRIPTION
PVC Cables2D4P5IPV3B-BU Category 5e 4 pair UTP Cable 305m Blue, CM
1.0 –100.0MHz Input Impedance (Ohms) 100±61.0 – 250.0MHz Delay Skew (ns/100m) ≤45Pair-to-Ground Capacitance Unbalance (pF/100m)
≤330
Max. Conductor DC Resistance 20˚C (Ohms/km)
93.8
Resistance Unbalance (%) ≤5Recommended Bend Radius 50
Actassi Product Overview Catalogue30
2D4P6IPV3B-BU
Conductor
Insulation
Filler
Rip Cord
Jacket
Category 6 UTP PVC CablesThe Actassi 4-Pair Category 6 Cable is a superior product delivering excellent network performance when used in conjunction with other Actassi Category 6 products. The Category 6 cable consists of 4 pairs of solid insulated copper 23AWG (0.57mm) and is UL listed with a CM fire rating. It is designed for use in horizontal cabling situations and supplied in 305m (1,000ft) easy pull out boxes.
The Category 6 cable provides a significant margin (10dB) above the minimum Category 6 Near End Crosstalk NEXT requirement of ANSI/TIA/ EIA-568 and ISO/IEC 11801.
TECHNICaL INFORMaTIONPhysical Specifications
Rated Temperature 75˚C
Product Standard Certification UL File E197794
Flammability Test CM
Application Horizontal Wiring in LAN
Reference Standard UL Subject 444, EIA/TIA 568-B.2 & ISO/IEC 11801, IEC61156-5
CONSTRUCTIONConductor Solid Bare Copper
AWG 23
Conductor Dia. Nom. (mm) 0.54
Insulation PE
Average Thickness (mm) 0.22
Min. Point Thickness (mm) 0.18
Insulation Diameter (±0.10mm) 0.95
Twisting Lay Length (mm) 30 underneath
Cabling Lay Length (mm) 200 underneath
Filler PE
Jacket PVC
Average Thickness (±0.05mm) 0.50
Min. Point Thickness (mm) 0.43
Outer Diameter (±0.2mm) 6.00
Rip Cord YES
PRODUCT FEaTURES• Complies with Category 6 ANSI/TIA/EIA-568 &
ISO/IEC 11801 Standard.• 23AWG conductors and the transmission is
certified to 250MHz.• UL Listed CM Fire rated.• Exceeds Category 6 ANSI/TIA/EIA-568 and ISO/
IEC 11801 Standards.• Supports transmission of digital and analogue
voice, data and video signal.• Supports Gigabit Ethernet (1000 Base-T).
ELECTRICaL CHaRaCTERISTICSFrequency
(MHz)Return Loss
(dB)Attenuation(dB/100m)
NEXT(dB)
ACR(dB)
PSNEXT(dB)
ELFEXT(dB)
PSELFEXT(dB)
Delay(ns/100m)
1 20.0 2.0 74.3 72 72.3 67.8 64.8 570.04 23.0 3.8 65.3 61 63.3 55.8 52.8 552.0
8 24.5 5.3 60.8 55 58.8 49.7 46.7 546.710 25.0 6.0 59.3 53 57.3 47.8 44.8 545.416 25.0 7.6 56.2 49 54.2 43.7 40.7 543.020 25 8.5 54.8 46 52.8 41.8 38.8 542.025 24.3 9.5 53.3 44 51.3 39.8 36.8 541.2
31.25 23.6 10.7 51.9 41 49.9 37.9 34.9 540.462.5 21.5 15.4 47.4 32 45.4 31.9 28.9 538.6100 20.1 19.8 44.3 25 42.3 27.8 24.8 537.6
CATALOGUE NUMBER DESCRIPTION
PVC Cables2D4P6IPV3B-BU Category 6 4 pair UTP Cable 305m Blue
Category 6 UTP Cables
1.0-100.0MHz Input Impedance (Ohms) 100±6100-250MHz Input Impedance (Ohms) 100±61.0-250.0MHz Delay Skew (ns/100m) ≤45Pair-to-Ground Capacitance Unbalance (pF/100m)
≤330
Max. Conductor DC Resistance 20˚C (Ohms/km)
73.2
Resistance Unbalance (%) ≤5Recommended Bend Radius 60
31
Notes
Actassi Product Overview Catalogue32
Actassi Installation Trunking
33
1. Trunking base 2. Front cover3. Internal corner4. External corner5. Bend, 90°,
including wall fixing6. Stop end7. Wall/Ceiling frame8. Joint cover piece
with jointing pieces9. T-piece10. Cable retainer11. Cable shelf12. Joint cover piece
for front cover13. Sealing strip
1
8
4
37
6
5
11
10
15
13
12
2
1
1
14
16
9P915
68
110
8
111
97
3 1
512
2
6
4 13
PVC trunkingOne compartment
Two compartments
Aluminium trunkingOne compartment
Two compartments
P91
045
P91
046
P91
047
P91
048
P91
049
P91
137
P91
138
P91
139
P91
140
P91
141
Actassi 70
Actassi 70 is a universal installation trunking system for all types of wiring devices. Available in lead and cadmium-free PVC. The PVC trunking and its 9PC/ABS accessories are white, RAL 9010.
aPPLICaTIONActassi 70 trunking gives the user reliable access to power, telephone and data close to the workplace offices, conference rooms and commercial buildings. The trunking has excellent universal functions both as an installation trunking for wiring devices and as a mere feeder trunking.
BENEFITS• Pre-punched slots in the partition walls of the PVC
trunking – easy to make holes to feed cables between the compartments.
• Adaptors and boxes with several unique installation benefits.
• 55 mm deep – high capacity and safe wire connections.
• Easy handling – trunking base and cover packed together, but not assembled.
• Protective foil on both sides of the trunking base and on the front cover, with printed pictures and product references.
DESIGN aND DIMENSIONS
EXPLODED VIEW
TECHNICaL aND MaTERIaL DaTaPVC (self-extinguishing, lead and cadmium-free)
Density 1.5 g/cm3
Linear expansion 60x10 -6/°C
Water absorption Less than 0.2%
Volume resistivity >1013 Ω cm
Fire rating UL 94 V0 (0.8 mm)
Fire/smoke/toxicity M1 acc. to French standard classification NF P 92 501
Colour White RAL 9010
Density 1.14 g/cm3
Linear expansion 70x10 -6/°C
Water absorption 0.6%
Volume resistivity >1013 Ω cm
Dielectric strength 19 kV/mm
Fire rating UL 94 HB
Colours White (unspecified)
Degree of protection IP40
Temperature range Operating temperature from -25°C to +60°C
Resistance to impact PVC trunking 2J (IK07)PC/ABS accessories 2J (IK07)
STaNDaRDS aND CERTIFICaTES The products comply with the standards:
EN 50085-1: 2005pr EN 50085-2-1: 2002
The products satisfy the provisions for CE marking according to the Low Voltage Directive 73/23/EEC and 93/68/EEC.
*
*
*
Actassi Product Overview Catalogue34
Trunking Actassi 70Installation Trunking
Cable capacityInstallation trunking 80x55, 95x55 and 120x55 mm
80x55, 95x55 and 120x55 without outletsIf the trunking is used as a feeder trunking please use this guide to calculate the cable capacity.
Trunk-ingsize
Fill factor100% 50%Inner area Inner area
3758 mm2 1879 mm2
4528 mm2 2264 mm2
5782 mm2 2891 mm2
80x55, 95x55 and 120x55 with Altira outletsIf the trunking is used as an installation trunking, please use this guide to calculate the cable capacity.
Trunk-ingsize
Fill factor100% 50%Inner area Inner area
2340 mm2 1170 mm2
3109 mm2 1555 mm2
4363 mm2 2182 mm2
No. of power cables, 3x2.5 mm2 (Ø 12 mm)
No. of VDI cables, FTP (Ø 7 mm)Trunking size 80x55Trunking size 95x55Trunking size 120x55
No. of power cables, 3x2.5 mm2 (Ø 12 mm)
No. of VDI cables, FTP (Ø 7 mm)
A more detailed calculation can be made in the OptiLine system speci� cation tool.
Fill factor 50%
Fill factor 50%
Trunking size 80x55Trunking size 95x55Trunking size 120x55
No. of power cables, 3x2.5 mm2 (Ø 12 mm)
No. of VDI cables, FTP (Ø 7 mm)Trunking size 80x55Trunking size 95x55Trunking size 120x55
80x55, 95x55 and 120x55 with Unica outletsIf the trunking is used as an installation trunking, please use this guide to calculate the cable capacity.
Trunk-ingsize
Fill factor100% 50%Inner area Inner area
1992 mm2 996 mm2
2761 mm2 1381 mm2
4015 mm2 2008 mm2
Fill factor 50%
P91
610
P91
485
P91
609
P91
487
P93
068
P92
514
Trunking Actassi 70Installation Trunking
Cable capacityInstallation trunking 155x55 mm
No. of power cables, 3x2.5 mm2 (Ø 12 mm)
No. of VDI cables, FTP (Ø 7 mm)
155x55 without outletsIf the trunking is used as a feeder trunking, please use this guide to calculate the cable capacity.
Com-part-ment
Fill factor100% 50%Inner area Inner area
3671 mm2 1836 mm2
3671 mm2 1836 mm2
155x55 with Altira outletsIf the trunking is used as an installation trunking please use this guide to calculate the cable capacity.
Com-part-ment
Fill factor100% 50%Inner area Inner area
2253 mm2 1127 mm2
2253 mm2 1127 mm2
Compartment 1Compartment 2
Compartment 1Compartment 2
No. of power cables, 3x2.5 mm2 (Ø 12 mm)
No. of VDI cables, FTP (Ø 7 mm)
A more detailed calculation can be made in the OptiLine system speci� cation tool.
Fill factor 50%
Fill factor 50%
155x55 with Unica outletsIf the trunking is used as an installation trunking please use this guide to calculate the cable capacity.
Com-part-ment
Fill factor100% 50%Inner area Inner area
1905 mm2 953 mm2
1905 mm2 953 mm2
Compartment 1Compartment 2
No. of power cables, 3x2.5 mm2 (Ø 12 mm)
No. of VDI cables, FTP (Ø 7 mm)
Fill factor 50%
P91
605
P91
489
P91
604
P91
491
P93
053
P92
515
Trunking Actassi 70Installation Trunking
Cable capacityInstallation trunking 185x55 mm
No. of power cables, 3x2.5 mm2 (Ø 12 mm)
No. of VDI cables, FTP (Ø 7 mm)
No. of power cables, 3x2.5 mm2 (Ø 12 mm)
No. of VDI cables, FTP (Ø 7 mm)
A more detailed calculation can be made in the OptiLine system speci� cation tool.
Fill factor 50%
Fill factor 50%
185x55 without outletsIf the trunking is used as a feeder trunking please use this guide to calculate the cable capacity.
Com-part-ment
Fill factor100% 50%Inner area Inner area
4407 mm2 2204 mm2
4407 mm2 2204 mm2
185x55 with Altira outletsIf the trunking is used as an installation trunking please use this guide to calculate the cable capacity.
Com-part-ment
Fill factor100% 50%Inner area Inner area
2989 mm2 1495 mm2
2989 mm2 1495 mm2
Compartment 1Compartment 2
Compartment 1Compartment 2
No. of power cables, 3x2.5 mm2 (Ø 12 mm)
No. of VDI cables, FTP (Ø 7 mm)
Fill factor 50%
185x55 with Unica outletsIf the trunking is used as an installation trunking please use this guide to calculate the cable capacity.
Com-part-ment
Fill factor100% 50%Inner area Inner area
2641 mm2 1321 mm2
2641 mm2 1321 mm2
Compartment 1Compartment 2
P91
493
P91
607
P91
606
P91
495
P93
062
P92
516
35
* Indent only
Trunking Actassi 70Installation Trunking
Type Colour Dimensions A/B/C (mm)
Qty perpackage
EAN code Internal ID-No.
Ref. No.
Material: PVC.
P89
106 For 45x45 module wiring
devices and modular devicesWhiteRAL 9010
80/55/2000 12 m 3606480028564 20053631 ISM11100
P89
108
For 45x45 module wiringdevices, modular devices and c/c 60 wiring devices
WhiteRAL 9010
95/55/2000 12 m 3606480028724 20053655 ISM11200*
P89
110
For 45x45 module wiring devices, modular devices and c/c 60 wiring devices
White RAL 9010
120/55/2000 12 m 3606480028854 20053661 ISM11300*
Material: PVC.
P89
114
For 45x45 module wiring devices and modular devices
WhiteRAL 9010
155/55/2000 8 m 3606480028991 20053668 ISM11400
P89
112
For 45x45 module wiringdevices, modular devices and c/c 60 wiring devices
WhiteRAL 9010
185/55/2000 8 m 3606480029134 20053675 ISM11500*
Adjustable internal corner for an 80–100 degree angling of PVC trunking.Material: PC/ABS.
P89
128
P89
174 For trunking 80x55 White
RAL 901089/117/117 1 3606480028571 20053632 ISM11101
For trunking 95x55 WhiteRAL 9010
104/117/117 1 3606480028731 20053656 ISM11201*
For trunking 120x55 WhiteRAL 9010
129/117/117 1 3606480028861 20053662 ISM11301*
For trunking 155x55 WhiteRAL 9010
164/117/117 1 3606480029004 20053669 ISM11401
For trunking 185x55 WhiteRAL 9010
194/117/117 1 3606480029141 20053676 ISM11501*
Adjustable external corner for a 75–135 degree angling of PVC trunking.Material: PC/ABS.
P89
129
P89
175 For trunking 80x55 White
RAL 901089/105/105 1 3606480028588 20053633 ISM11102
For trunking 95x55 WhiteRAL 9010
104/105/105 1 3606480028748 20053657 ISM11202*
For trunking 120x55 WhiteRAL 9010
129/105/105 1 3606480028878 20053663 ISM11302*
For trunking 155x55 WhiteRAL 9010
164/105/105 1 3606480029011 20053670 ISM11402
For trunking 185x55 WhiteRAL 9010
194/105/105 1 3606480029158 20053677 ISM11502*
INSTALLATION TRUNKING WITH ONE COMPARTMENT
INSTALLATION TRUNKING WITH TWO COMPARTMENTS
INTERNAL CORNER
EXTERNAL CORNER
PVC TRUNKING
ACCESSORIES FOR PVC TRUNKING
Installation trunking including one-compartment trunking base and front cover. The trunking base has pre-punched mounting holes every 25th cm and can be provided with cable shelves. The 70 mm front opening allows wiring devices to be mounted by using adaptors. Trunking base and front cover are supplied unassembled under separate protective foil, in lengths of 2m.
Installation trunking including two-compartment trunking base and two front covers. The trunking base has pre-punched mounting holes every 25th cm and can be provided with cable shelves. The integrated partition wall has pre-punched slots every 25th cm to facilitate cable laying. The 70 mm front opening allows wiring devices to be mounted by using adaptors. Trunking base and front decover are supplied unassembled under separate protective foil, in lengths of 2m.
Actassi Product Overview Catalogue36
Trunking Actassi 70Installation Trunking
Type Colour DimensionsA/B/C (mm)
Qty perpackage
EAN code Internal ID-No.
Ref. No.
90 degree bend kit for angling upwards and downwards of PVC trunking. Including bend piece and fixing device to be screw-fitted to the wall.Material: PC/ABS.
P89
176
For trunking 80x55 WhiteRAL 9010
107/57/107 1 3606480028595 20053634 ISM11103
For trunking 95x55 WhiteRAL 9010
122/57/122 1 3606480028755 20053658 ISM11203*
For trunking 120x55 WhiteRAL 9010
147/57/147 1 3606480028885 20053664 ISM11303*
For trunking 155x55 WhiteRAL 9010
182/57/182 1 3606480029028 20053671 ISM11403
For trunking 185x55 WhiteRAL 9010
212/57/212 1 3606480029165 20053678 ISM11503*
Stop end for PVC trunking. Fast fitting with locking clips. Screw-fixing possible for extra security. Material: PC/ABS.
P89
177 For trunking 80x55 White
RAL 901064/56/21 2 3606480028601 20053635 ISM11104
For trunking 95x55 WhiteRAL 9010
99/56/21 2 3606480027901 20051948 ISM10204*
For trunking 120x55 WhiteRAL 9010
124/56/21 2 3606480028892 20053665 ISM11304*
For trunking 155x55 WhiteRAL 9010
159/56/21 2 3606480029035 20053672 ISM11404
For trunking 185x55 WhiteRAL 9010
189/56/21 2 3606480028298 20051945 ISM10504*
Wall/Ceiling frame to be fitted around a PVC trunking at wall or ceiling passage. Easily modified to C or L-profile depending on how the passage is made. Snap-fitted, with a screw-fixing option for high security.Material: PC/ABS.
P89
178
For trunking 80x55 WhiteRAL 9010
135/82/22 1 3606480028618 20053636 ISM11105
For trunking 95x55 WhiteRAL 9010
150/82/22 1 3606480028762 20053659 ISM11205*
For trunking 120x55 WhiteRAL 9010
175/82/22 1 3606480028908 20053666 ISM11305*
For trunking 155x55 WhiteRAL 9010
210/82/22 1 3606480029042 20053673 ISM11405
For trunking 185x55 WhiteRAL 9010
240/82/22 1 3606480029172 20054134 ISM11505*
Joint cover piece, supplied and mounted together with two jointing pieces. Intended to cover joints between two PVC trunking sections. Easy to remove in case of an upgrading of the installation.Material: PC/ABS.
P89
179 For trunking 80x55 White
RAL 901085/57/100 1 3606480028625 20053637 ISM11106
For trunking 95x55 WhiteRAL 9010
100/57/100 1 3606480028076 20053660 ISM11206*
For trunking 120x55 WhiteRAL 9010
125/57/100 1 3606480028915 20053667 ISM11306*
For trunking 155x55 WhiteRAL 9010
160/57/100 1 3606480029059 20053674 ISM11406
For trunking 185x55 WhiteRAL 9010
190/57/100 1 3606480029189 20053679 ISM11506*
BEND, 900, KIT
STOP END
WALL/CEILING FRAME
JOINT COVER PIECE, KIT
ACCESSORIES FOR PVC TRUNKING
* Indent only
37
Trunking Actassi 70Installation Trunking
Type Colour DimensionsA/B/C (mm)
Qty perpackage
EAN code Internal ID-No.
Ref. No.
P89
180 T-piece intended to connect a vertical to a horizontal PVC trunking.
Material: PC/ABS.For vertical trunking 80x55 and horizontal trunking 80x55
WhiteRAL 9010
52/57/102 1 3606480028632 20053638 ISM11107
P89
181
Front cover to be snap-fitted in trunking with a 70 mm front opening. Supplied with protective foil, in lengths of 2 m.Material: PVC
Front cover White RAL 9010
71/13/2000 24 m 3606480029257 20053639 ISM11900
P89
183
Cable retainer to be mounted at the back of the trunking base to keep cables in place during the installation phase. Also providing increased cable capacity when used in a one-compartment trunking. No need to remove the retainer when fitting the front cover. Material: PA.Cable retainer Blue 42/48/25 5 3606480029264 20053640 ISM11901
P85
788
Single cable shelf to be mounted in the trunking base, providing separation between power and low voltage cables. Supplied in lengths of 1 m.Material: PVC.Cable shelf White
RAL 901017/47/1000 24 m 3606480028410 20051964 ISM10902
P91
615 Joint cover piece intended to cover joints between two PVC front covers.
Material: PC/ABS.Joint cover piece for front cover White
RAL 901071/24/23 5 3606480029271 20053641 ISM11903
P89
184
Internal jointing piece intended to facilitate jointing of two PVC or aluminium trunking bases. May also be used to mount the joint cover piece. Material: PC/ABS.Jointing piece White
RAL 90104/39/100 10 3606480029288 20053642 ISM11904
P85
791
Sealing strip to be fitted between trunking and floor for a 10-15 mm coverage. Supplied in lengths of 2 m. Material: PVC.
Sealing strip WhiteRAL 9010
17/40/2000 24 m 3606480028441 20051952 ISM10905
Adaptor including front plate. Suitable for 45x45 module wiring devices, type Altira and similar. Terminal blocks and earth terminals can be snap-fitted in the two-module and three-module sizes. To be combined with installation box in applications requiring strain relief of cables or extra insulation. Altira front plate for wall applications can be snap-fitted in the adaptor. To avoid gaps between wiring devices the adaptors can be snapped into one another.Material: PC/ABS.
P91
590 For one 45x45 module wiring
deviceWhite RAL 9010
73/35/71 1 3606480029417 20053646 ISM15100
P91
591
For two 45x45 module wiring devices
WhiteRAL 9010
73/35/140 1 3606480029424 20053647 ISM15101
P91
592
For three 45x45 module wiring devices
White RAL 9010
73/35/185 1 3606480028431 20053648 ISM15102
T-PIECE
ACCESSORIES FOR PVC TRUNKING
FRONT COVER
CABLE RETAINER
CABLE SHELF
JOINT COVER PIECE FOR FRONT COVER
JOINTING PIECE
SEALING STRIP
ADAPTER FOR 45X45 MODULE WIRING DEVICE, ALTIRA
Actassi Product Overview Catalogue38
Environment-friendlyActassi 70 mini-trunking is available in halogen freeplastic (PC/ABS). Accessories,like corners and end pieces, are made of halogen-free plastic (PC/ABS).
The new Actassi 70 mini-trunking system is based on more than 40 years’ experience of developing trunking for electrical installations. The aim was to develop an attractive, functional trunking to meet many different needs, often for small installations.The trunking would also need to be easy to install and extend, to provide greater electrical safety and be more tamper-resistant than any previous trunking.In addition to all this it would have to be attractive to look at.
The result is a smoothly shaped trunking in many sizes and variants, and with accessories which gives fl exible and safe installations.
Smoothly shaped and fl exible
Both outdoors and indoorsThanks to its sealed, stable design, Actassi 70 mini-trunking achieves degree of protection IP40. This makes Actassi 70 mini-trunking suitable for installation both outdoors and indoors. The plastic offers many years of resistance to UV radiation, heat and cold. The plastic trunking is also approved for single-insulated wire outdoors.
Highly impact-resistantAll mini-trunking is highly impact-resistant, thanks to its design and generous material thickness. In many cases, this is a secure substitute for unattractive sheet steel protection.
2
Actassi 70 Mini Trunking
The Actassi 70 mini-trunking system is based on more than 40 years’ experience of developing trunking for electrical installations. The aim was to develop an attractive, functional trunking to meet many different needs, often for small installations. The trunking would also need to be easy to install and extend, to provide greater electrical safety and be more tamper-resistant than any previous trunking. In addition to all this it would have to be attractive to look at.
The result is a smoothly shaped trunking in many sizes and variants, and with accessories which gives flexible and safe installations.
39
Actassi 70 Mini Trunking Range
Single-insulated wireFor single-insulated wire to be installed in mini-trunking, the trunking must satisfy stringent electrical safety requirements. The plastic version of Actassi 70 mini-trunking meets these requirements.Among the advantages of single-insulated wire are that it is easy to install and that more wires can be fi tted into the trunking. It is also an advantage at transitions to or from a fl ush installation.
Partition wallsThe partitions in two- and three-compartment plastic trunking can be easily broken off with one’s fi ngers. First simply cross-cut the partition to the correct length with side cutters.The trunking can be cut by hand with simple tools – no need for precision. The accessories are very forgiving!
Screws or adhesive tapeAll Actassi 70 mini-trunking has pre-punched holes at frequent intervals to make installation easier.For installations without power wiring, there is also mini-trunking with adhesive tape fi xing. On suitablesurfaces, the speed of this method of installation is unsurpassed.
Tamper-proofThe trunking and all its accessories use snap fi tting for quick, simple installation. To remove the cover and accessories without the right tools is far more diffi cult.This is a design feature that protects the installation from tampering, especially recom-mended in public areas or for fi bre optic and broadband cables.
Cable separationMixed installations in which power and data wiring is run to the same point are becoming increasingly common. This is why Actassi 70 mini-trunking is available with several compartments, so that the entire installation can be accommodated in one trunking. Having more than one compartment also
feeds in the same trunking.
Branching pieceCreate a combined trunking installation by running the feed in two- or three-compartment PVC trunking and then connecting, for example, aluminium trunking where extra impact resist-ance or a more exclusive impression is needed. The practical branching piece makes changes of dimension simple.
Cable clampTo keep the cables in place during the installation phase, cable holders are available as accessories.They are easy to snap-fi t and can remain in place when the cover is fi tted.
Fly-overFor installations in two-and three-compartment trunking, it becomes necessary to separate power and data cables where they cross each other.For this, the fl y-over is used at branch points. The fl y-over can be adapted as neces-sary by easily breaking off unwanted partitions.
makes it possible to run long
3
Actassi Product Overview Catalogue40
Actassi 70 Mini Trunking Technical description
Actassi 70Mini-trunking
Technical description
PVC (base, cover) Characteristics: Rigid, self-extinguishing, cadmium- eerf-dael ,eerf
0109 LAR etihW :sruoloC mc/g 5.1 :ytisneD 3
Linear expansion: 60x10–6/°CPC/ABS (base, cover, acces- Characteristics: Halogen-free
0109 LAR etihW :sruoloC )seiros)detniap( cillatem muinimulA
mc/g 41.1 ytisneD 3
Linear expansion: 70x10–6/°CDegree of protection IP40Installation and application Plastic trunking: temperature –15/+60°C (1220 and 1820)
)0652 dna 5481 ,5381 ,0321( C°06+/52– Resistance to impact Plastic trunking:
)0281 dna 0221( J1 • )0652 dna 5481 ,5381 ,0321( J2 •
Delivery lengths 2.1 metresStandards and certifi cates The product complies with the standards:
5002:1-58005 NE • 6002:1-2-58005 NE •
gnidrocca gnikram EC rof snoisivorp eht yfsitas stcudorp ehT .CEE/86/89 dna CEE/32/37 evitceriD egatloV woL eht ot
CE/59/2002 evitcerid SHoR eht htiw ylpmoc stcudorp ehT secnatsbuS suodrazaH fo noitcirtseR(
1. Base profi le2. Cover3. Internal corner4. External corner5. 90° bend
6. T-piece7. Branching piece8. Joint cover piece9. Stop end10. Fly-over
12
34
6
5
7
9
8
10
P85
025
Design and dimensions, material
18x45 25x60
45
19
19
18
P64
115
60
16
17
16
25
P64
116
Technical and Material dataExploded view
6
41
INTERNAL CORNER
EXTERNAL CORNER
BEND,900
STOP END
Actassi 70 Mini-trunking
Range
MINI-TRUNKINGsnoisnemiDruoloCepyT
A/B/C (mm) Qty perpackage
Ref. No.
Mini-trunking including base profi le with one, two or three compartments, and snap-fi tted cover. Partition walls can be removed. With pre-punched mounting holes at 100 mm centres. Suitable for power and low voltage cables. Approved for single-insulated cable if non-metallic fastener is used. Supplied in 2.1 m lengths.Material: PVC.
P83
325 With two compartments White RAL 9010 45/18/2100 42 m ISM14500
P83
326 With three compartments White RAL 9010 60/25/2100 21 m ISM14600
Actassi 70 Mini-trunking
Range
ACCESSORIESsnoisnemiDruoloCepyT
A/B/C (mm) Qty perpackage
Ref. No.
Internal corner to be snap-fi tted onto the mini-trunking base.Material: PC/ABS.
P83
921
10541MSI0154/54/740109 LAR etihWgniknurt-inim 54x81 roF
10641MSI0135/35/260109 LAR etihWgniknurt-inim 06x52 roF
External corner to be snap-fi tted onto the mini-trunking base.Material: PC/ABS.
P83
922 20541MSI0124/24/740109 LAR etihWgniknurt-inim 54x81 roF
20641MSI0194/94/260109 LAR etihWgniknurt-inim 06x52 roF
90 degree bend to be used in junctions between horizontal and vertical applications. To be snap-fi tted onto the mini-trunking base. Material: PC/ABS.
P83
924
30541MSI0156/56/810109 LAR etihWgniknurt-inim 54x81 roF
30641MSI0108/08/420109 LAR etihWgniknurt-inim 06x52 roF
Stop end to be snap-fi tted at the end of the mini-trunking base.Material: PC/ABS.
P83
925
40541MSI0191/51/740109 LAR etihWgniknurt-inim 54x81 roF
40641MSI0162/71/260109 LAR etihWgniknurt-inim 06x52 roF
4
PVC MINI-TRUNKING
Actassi 70 Mini Trunking Range
Actassi Product Overview Catalogue42
Actassi 70 Mini-trunking
Range
ACCESSORIESsnoisnemiDruoloCepyT
A/B/C (mm) Qty perpackage
Ref. No.
Joint cover piece to cover joints between mini-trunking covers.Material: PC/ABS.
P83
926 50541MSI0191/22/740109 LAR etihWgniknurt-inim 54x81 roF
50641MSI0162/22/260109 LAR etihWgniknurt-inim 06x52 roF
T-piece to be used in T-junctions between mini-trunking of the same size. To be snap-fi tted onto the mini-trunking base.Material: PC/ABS.
P83
923
60541MSI0138/56/810109 LAR etihWgniknurt-inim 54x81 roF
60641MSI0189/08/420109 LAR etihWgniknurt-inim 06x52 roF
Branching piece to be used in T-junctions between mini-trunking of different sizes.Material: PC/ABS.
P83
927 70541MSI0171/05/460109 LAR etihWgniknurt-inim 54x81– 02x21 roF
70641MSI0142/56/970109 LAR etihWgniknurt-inim 06x52–53x81 roF
Fly-over to be used in combination with T-piece or branching piece. Intended to secure separation between compartments when single-insulated cable is used.Material: ABS
P77
777
80441MSI0103/03/31etihWgniknurt-inim 53x81 roF
P77
053
80641MSI0155/55/02etihWgniknurt-inim 06x52 roF
5
T-PIECE
BRANCHING PIECE
FLY-OVER
JOINT COVER PIECE
Actassi 70 Mini Trunking Range
43
Notes
44
Actassi Fibre
45
2F6CMIOR50
PHYSICaL SPECIFICaTIONSCore Diameter 50±2.5µmCladding Diameter 125.0±1µm Cladding Non-circularity ≤1.0% Coating Diameter 245±10µm Coating/Cladding Concentricity Error ≤12µm Coating Diameter Non-circularity ≤6.0% Core/Cladding Concentricity Error ≤1.5µm Delivery Length (km/reel) Sold only in 1000 Metre Drums
OPTICaL CHaRaCTERISTICS
Indoor/Outdoor LSZH Cables, Multi-ModeDuct Cables
CATALOGUE NUMBER DESCRIPTION ACTNUD06MM5TLS Indoor/Outdoor, LSZH, Multi-Mode, 6 Core, 50µmACTNUD12MM5TLS Indoor/Outdoor, LSZH, Multi-Mode, 12 Core, 50µm2F6CMIOR50 Indoor/Outdoor, 6 Core OM3 Riser
The Actassi Indoor Outdoor LSZH Cable is a low smoke zero halogen (LSZH) cable that provides excellent anti-flame performance. The need for splicing between indoor and outdoor cables can be eliminated. The buffered tubes are surrounded by aramid yarns and are covered by a low smoke, flame-retardant jacket for protection. A direct outdoor to indoor transition can be completed with this single cable.
The Indoor Outdoor LSZH Cable passed the following tests: • IEC 754 part 3, Acidity/Corrosively based on pH and Conductivity Measurements • IEC 332 part 3, Flammability and Fire Retardant • NES 713, Toxicity Index • IEC 1034, Smoke Emissions
PRODUCT FEaTURES• Complies with ANSI/TIA/EIA-568-B.3 Standards.• All dielectric self-supporting fibre.• Filled with water-resistant filling compound.• LSZH rated.
CUSTOMER BENEFITS• Supports Gigabit Ethernet application.• Suitable for indoor/outdoor or inter/intra building backbones installation.• Water-blocking.• Excellent anti-flame performance.
50/125µm
Attenuation (+20ºC) @850nm ≤3.0dB / km
@1300nm ≤1.0dB / km
@1310nm
@1550nm
Bandwidth @850nm ≥500MHz.km
@1300nm ≥1000MHz.km
Numerical Aperture 0.200±0.015 NA
Cable Cut-off Wavelength cc
Actassi Product Overview Catalogue46
Actassi Fibre Patch Panels & Splice Trays
The Actassi Fibre Management Enclosure is a superior and compact fibre termination solution. It provides a rack/cabinet mountable solution with a provision to splice up to 48 external optional fibres to 48 pigtails. Installed with a pair of cable radius guides, this enclosure can also facilitate a maximum of 24 fibre patching applications.
This powder coated steel enclosure comes with a transparent removable Plexiglass cover for ease of installation, inspection and testing. Innovated design such as slide in/out cable entry provides additional flexibility during installation, movement or changes in the future.
Designed with multiple applications in mind, the Actassi Fibre Management Enclosure can accommodate different types of modular adapter panels and splice trays (optional) to give outstanding performance and functionality.
TECHNICaL SPECIFICaTIONSMaterial Powder Coated Mild SteelAccommodation Up to 24 x ST Connectors Up to 24 x SC Connectors Up to 48 LC Connectors Up to 48 x MTRJ ConnectorsCable Termination Direct TerminationOptions Mechanical & Fusion Splicing
PRODUCT FEaTURES• 1U panel and 19” front rack mounting
enclosure provides patching and fibre slack storage capability conduit or standard tube interfacing.
• Accommodates up to 3 connector panels.• Access connector panel with front quick
release latch cover.• Nylon cable radius guide and centre strength
member clamp.• Cable fibre track cover provides additional
protection and a clean outlook.• Transparent, easy access slide-out and
removable Plexiglass cover.• Additional rear mount ears (a set of 2) for
cabinet mounting.• Rugged steel construction in graphite finish.• Optional splice tray can be mounted to the
unit.• Slide in cable entry panel with 2 x 25mm
diameter holes.
CUSTOMER BENEFITS• Provide patching and fibre slack storage ca-
pability with technicians and users in mind: - the technician’s side has facilities for securing the cable, storing fibre slack and arranging the terminated fibres. - the user’s side has similar features for the management of fibre optic patch cord.
• 66mm deep front cable panel for patch cord management and protection.
• Side-out Medium Density optical fibre man-agement enclosure for optimum access, to ease installation, inspection and testing.
• Slide-in cable entry panel with 2 x 25mm diameter holes allow flexible conduit or standard tube interfacing during installation.
• Nylon cable radius guide within the enclosure to accommodate excess fibres while main-taining fibre bend radius.
• Cable fibre track cover to give additional protection and clean outlook.
• Optional splice tray can be mounted to man-age and protect either fusion or mechanical splices.
CATALOGUE NUMBER DESCRIPTION ACTFM1UU 1U, 24-Port Fibre Sliding Enclosure, UnloadedACTFM1UB 1U, Fibre Blank Connector PanelACTFMSPT Fusion 24 Splice TrayACTFM1U2LC4P Adaptor Panel LC Duplex C/W 4 ConnectorsACTFM1U2LC8P Adaptor Panel LC Duplex C/W 8 Connectors
47
SC Fibre Patch Cords
ACTFP1C3S19S10
PRODUCT FEaTURES • Meets ANSI/TIA/EIA 568-B.3 and ISO/
IEC 11801 Standards.• Patch cords are available in Simplex,
Duplex, Single-Mode and Multi-Mode configurations with different length options.
• Cords are easy-to-install and environmentally stable.
CUSTOMER BENEFITS• Supports LAN, WAN and active device
termination.• All cords are factory terminated and
tested.• Provides a reliable and durable
connection solution.
PHYSICaL SPECIFICaTIONSCoated Fibre Diameter 250µmCable Outside Diameter Simplex: 3.0mm; Duplex: 6.6mm x 3.6mmMin. Bend Radius 3.8cm
OPTICaL SPECIFICaTIONSMulti-ModeMin. Bandwidth @850nm 200MHz-km@1300nm 500MHz-kmSingle-ModeAverage Loss 0.3dB/mated connectorReturn Loss -50dB max.
MECHaNICaL CHaRaCTERISTICSConnectorFerrule Materials Zirconia Ceramic Housing Body Engineered Resin CableBoot Thermoplastic Elastomer Flammability UL 94V-0 Glass Core/Cladding Diameter Single-Mode (SM) Multi-Mode (MM) 9/125µm 50/125µm or 62.5/125µm Polymer Coating Diameter 125µmJacket Specification OFNR/LSZH
PERFORMaNCE Connector SC Mean Insertion Loss 0.2dB Maximum Insertion Loss 0.4dB Maximum Reflection -50dB (SM)/-25dB (MM)Connector Durability) <0.2dB max. (500 matingsCable 50 (MM) Cable Attenuation 3.5dB/km (SM)/1.5dB/km (MM) @ 23˚C Typical ENVIRONMENTaL Operating Temperature Range 0˚C to 70˚C Storage Temperature Range -10˚C to 75˚C
The Simplex and Duplex SC Fibre Patch Cords are 3.0mm cordage with push-pull SC connectors terminated on each end. These patch cords are available in Simplex*, Duplex, Multi-Mode and Single-Mode* configurations.
Duplex OM3, Multi-Mode ACTFP2C3M35M10 SC-SC OM3 50µm duplex, multi-mode, patch cord 1mACTFP2C3M35M20 SC-SC OM3 50µm duplex, multi-mode, patch cord 2mACTFP2C3M35M30 SC-SC OM3 50µm duplex, multi-mode, patch cord 3mACTFP2C3M35M50 SC-SC OM3 50µm duplex, multi-mode, patch cord 5mACTFP2C3M35M100 SC-SC OM3 50µm duplex, multi-mode, patch cord 10m
* Simplex and Single-Mode are indent and available on request
Actassi Product Overview Catalogue48
ST Fibre Patch Cords
PHYSICaL SPECIFICaTIONSCoated Fibre Diameter 250µmCable Outside Diameter Simplex: 3.0mm; Duplex: 6.6mm x 3.6mmMin. Bend Radius 3.8cm
OPTICaL SPECIFICaTIONSMulti-ModeMin. Bandwidth @850nm 200MHz-km@1300nm 500MHz-kmSingle-ModeAverage Loss 0.3dB/mated connectorReturn Loss -50dB max.
MECHaNICaL CHaRaCTERISTICSConnector Ferrule Materials Zirconia Ceramic Housing Body Nickel Plated Zinc Cable Boot Thermoplastic ElastomerFlammability UL 94V-0 Glass Core/Cladding Diameter Single-Mode (SM) Multi-Mode (MM) 9/125µm 50/125µm or 62.5/125µm Polymer Coating Diameter 125µm Jacket Specification OFNR/LSZH
PERFORMaNCE Connector ST Mean Insertion Loss 0.2dB Maximum Insertion Loss 0.4dB Maximum Reflection -50dB (SM)/-25dB (MM)Connector Durability <0.2dB max. (500 matings)Cable 9 (SM)/50 (MM) Cable Attenuation 3.5dB/km (SM)/1.5dB/km (MM) @ 23˚C Typical ENVIRONMENTaL Operating Temperature Range 0˚C to 70˚C Storage Temperature Range -10˚C to 75˚C
PRODUCT FEaTURES • Meets ANSI/TIA/EIA 568-B.3 and
ISO/IEC 11801 Standards.• Patch cords are available in Single-
Mode and Multi-Mode configurations with different length options.
• Cords are easy-to-install and environmentally stable.
CUSTOMER BENEFITS• Supports LAN, WAN and active device
termination.• Provides a reliable and durable
connection solution.• All cords are factory terminated and
tested.
The Simplex and Duplex ST Fibre Patch Cords are 3.0mm cordage with push-pull ST connectors terminated on each end. These patch cords are available in Simplex*, Duplex, Multi-Mode and Single-Mode* configurations.
ACTFP1T3S19S10
* Simplex and Single-Mode are indent and available on request
Duplex OM3, Multi-ModeACTFP2T3M35M10 ST-ST OM3 50µm duplex, multi-mode, patch cord 1m ACTFP2T3M35M20 ST-ST OM3 50µm duplex, multi-mode, patch cord 2m ACTFP2T3M35M30 ST-ST OM3 50µm duplex, multi-mode, patch cord 3m ACTFP2T3M35M50 ST-ST OM3 50µm duplex, multi-mode, patch cord 5m ACTFP2T3M35M100 ST-ST OM3 50µm duplex, multi-mode, patch cord 10m
49
LC Fibre Patch Cords
ACTFP1L3S19S10
PHYSICaL SPECIFICaTIONSCoated Fibre Diameter 250µmCable Outside Diameter Simplex: 3.0mm; Duplex: 6.6mm x 3.6mmMin. Bend Radius 3.8cm
OPTICaL SPECIFICaTIONSMulti-ModeMin. Bandwidth @850nm 200MHz-km@1300nm 500MHz-kmSingle-ModeAverage Loss 0.3dB/mated connectorReturn Loss -50dB max.
MECHaNICaL CHaRaCTERISTICSConnectorFerrule Materials Zirconia Ceramic Housing Body Engineered Resin CableBoot Thermoplastic Elastomer Flammability UL 94V-0 Glass Core/Cladding Diameter Single-Mode (SM) Multi-Mode (MM) 50/125µm 9/125µm or 62.5/125µm Polymer Coating Diameter 125µm Jacket Specification OFNR/LSZH
PERFORMaNCE Connector LC Mean Insertion Loss 0.2dB Maximum Insertion Loss 0.4dB Maximum Reflection -50dB (SM)/-25dB (MM)Connector Durability <0.2dB max. (500 matings)Cable 9 (SM)/50 (MM) Cable Attenuation 3.5dB/km (SM)/1.5dB/km (MM) @ 23˚C Typical
ENVIRONMENTaL Operating Temperature Range 0˚C to 70˚C Storage Temperature Range -10˚C to 75˚C
The Simplex and Duplex LC Fibre Patch Cords are 3.0mm cordage with push-pull LC connectors terminated on each end. These patch cords are available in Simplex*, Duplex, Multi-Mode and Single-Mode* configurations.
* Simplex and Single-Mode are indent and available on request
Duplex OM3, Multi-ModeACTFP2L3M35M10 LC-LC OM3 50µm, duplex, multi-mode, patch cord, 1m ACTFP2L3M35M20 LC-LC OM3 50µm, duplex, multi-mode, patch cord, 2m ACTFP2L3M35M30 LC-LC OM3 50µm, duplex, multi-mode, patch cord, 3m ACTFP2L3M35M50 LC-LC OM3 50µm, duplex, multi-mode, patch cord, 5m ACTFP2L3M35M100 LC-LC OM3 50µm, duplex, multi-mode, patch cord, 10m
Actassi Product Overview Catalogue50
Duplex OM3, Multi-ModeACTFP2CL3M35M10 SC-LC OM3 50µm, duplex, multi-mode, patch cord, 1mACTFP2CL3M35M20 SC-LC OM3 50µm, duplex, multi-mode, patch cord, 2m ACTFP2CL3M35M30 SC-LC OM3 50µm, duplex, multi-mode, patch cord, 3mACTFP2CL3M35M50 SC-LC OM3 50µm, duplex, multi-mode, patch cord, 5m ACTFP2CL3M35M100 SC-LC OM3 50µm, duplex, multi-mode, patch cord, 10m
SC-LC Fibre Patch Cords
ACTFP1CL3S19S10
PRODUCT FEaTURES • Meets ANSI/TIA/EIA 568-B.3 and
ISO/IEC 11801 Standards.• Patch cords are available in Duplex,
Multi-Mode configurations with different length options.
• Cords are easy-to-install and environmentally stable.
CUSTOMER BENEFITS• Supports LAN, WAN and active
device termination.• Provides a reliable and durable
connection solution.• All cords are factory terminated and
tested.
PHYSICaL SPECIFICaTIONSCoated Fibre Diameter 250µmCable Outside Diameter Duplex: 6.6mm x 3.6mmMin. Bend Radius 3.8cm
OPTICaL SPECIFICaTIONSMulti-ModeMin. Bandwidth @850nm 200MHz-km@1300nm 500MHz-kmSingle-ModeAverage Loss 0.3dB/mated connectorReturn Loss -50dB max.
MECHaNICaL CHaRaCTERISTICSConnectorFerrule Materials Zirconia Ceramic Housing Body Engineered Resin Cable Boot Thermoplastic Elastomer Flammability UL 94V-0 Glass Core/Cladding Single-Mode (SM) Multi-Mode (MM) Diameter 9/125µm 50/125µm or 62.5/125µm Polymer Coating Diameter 125µm Jacket Specification OFNR/LSZH
PERFORMaNCE Connector SC LCMean Insertion Loss 0.2dB 0.2dBMaximum Insertion Loss 0.4dB 0.4dBMaximum Reflection -50dB (SM)/-25dB (MM) -50dB (SM)/-25dB (MM)Connector Durability (500 matings) <0.2dB max. <0.2dB max.Cable 9 (SM)/50 (MM) 9 (SM)/50 (MM)Cable Attenuation 3.5dB/km (SM)/ 3.5dB/km (SM)/ @ 23˚C Typical 1.5dB/km (MM) 1.5dB/km (MM)
ENVIRONMENTaL Operating Temperature Range 0˚C to 70˚C Storage Temperature Range -10˚C to 75˚C
The Duplex SC-LC Fibre Patch Cords are 3.0mm cordage with push-pull SC-LC connectors terminated on each end. These patch cords are available in Duplex Multi-Mode configurations.
51
CATALOGUE NUMBER DESCRIPTIONSC AdaptorsACTFA1CSMZP SC Adaptor, Simplex, Single-Mode, Zirconia Ceramic, PlasticACTFA1CMMZP SC Adaptor, Simplex, Multi-Mode, Zirconia Ceramic, PlasticACTFA2CMMZP SC Adaptor, Duplex, Multi-Mode, Zirconia Ceramic, Plastic
LC AdaptorsACTFA2LSMZP LC Adaptor, Duplex, Single-Mode, Zirconia Ceramic, PlasticACTFA2LMMZP LC duplex multi-mode adapter
Through Adaptors
The Actassi Fibre Optic Connectors and Adaptors are superior products delivering the best networking performance when used in conjunction with other Actassi Fibre Optic products.
ACTFA1CSMZP ACTFA2CSMZP ACTFA2LMMZP
ACTFA2LSMZP
Actassi Product Overview Catalogue52
Notes
Must retain these 2 pages in order for the document to be dividable by four
53
Notes
Must retain these 2 pages in order for the document to be dividable by four
54All rights reserved by Schneider Electric.
NV
MP
RTA
CTA
SS
I031
4
about Schneider ElectricAs a global specialist in energy management with operations in more than 100 countries, Schneider Electric offers integrated solutions across multiple market segments, including leadership positions in energy and infrastructure, industrial processes, building automation, and data centres/networks, as well as a broad presence in residential applications. Focused on making energy safe, reliable, and efficient, the company’s 130,000 plus employees achieved sales of 22.4 billion Euros in 2011, through an active commitment to help individuals and organisations “Make the most of their energy.”
www.schneider-electric.com
www.actassi.com
Customer Care: 0800 652 999Email: [email protected]/nz
38 Business Parade South, East Tamaki, Manukau 2013PO Box 259370, Botany, Manukau 2163Tel: +64 9 829 0490 Fax: +64 9 829 0491
Schneider Electric (NZ) Ltd.
© 2014 Schneider Electric. As standards, specifications and designs change from time to time, always ask for confirmation of the information given in this publication.