ARMY TM 5-822-7AIR FORCE AFM 88-6, Chap. 8

DEPARTMENTS OF THE ARMY AND THEAIR FORCE TECHNICAL MANUAL

STANDARD PRACTICE FOR CONCRETE PAVEMENTS

DEPARTMENTS OF THE ARMY AND THE AIR FORCEAUGUST 1987

REPRODUCTION AUTHORIZATION/RESTRICTIONS

TECHNICAL MANUALNo. 5-822-7AIR FORCE MANUALNo. 88-6, Chapter 8

HEADQUARTERSDEPARTMENTS OF THE ARMY

AND THE AIR FORCEWashington, DC 16 August 1987

STANDARD PRACTICE FOR CONCRETE PAVEMENTS

Paragraph Page

PURPOSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SCOPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RESPONSIBILITIES, STRENGTH, AND AIR CONTENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .CEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AGGREGATES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ADMIXTURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . POZZOLANS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MISCELLANEOUS MATERIALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .WATER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SAMPLING AND TESTING OF MATERIALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .DELIVERY AND STORAGE OF MATERIALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GRADE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PROPORTIONING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .SUBGRADE, BASE, FORMS, AND STRING LINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .BATCHING AND MIXING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PLACING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .FIELD TEST SPECIMENS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FINISHING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CURING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GRADE AND SURFACE -SMOOTHNESS REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TOLERANCES IN PAVEMENT THICKNESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .REPAIRS OF DEFECTIVE PAVEMENT SLABS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .JOINTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PAVEMENT PROTECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MEASUREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . APPENDIX A: REFERENCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .APPENDIX B: THIN BONDED RIGID OVERLAYS FOR RIGID PAVEMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . APPENDIX C: STEEL-FIBER- REINFORCED CONCRETE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .APPENDIX D: ROLLER-COMPACTED CONCRETE PAVEMENTS; DESIGN AND CONSTRUCTION............

123456789

10111213141516171819202122232425

11134

1111121212131313151517202123232424242727

A-1B-1C-1D-1

i

Figure 1.2.3.

D-1.D-2.D-3.D-4.D-5.

Table 1.2.3.4.5.6.7.8.

C-1.C-2.D-1.

LIST OF FIGURES

Prediction of concrete rate of evaporation.Air Force runway grooving requirements.Special joint between new and existing pavement.Typical layout for RCCP test section.Compaction of first paving lane.Compaction of interior paving lanes.Construction of a cold joint.Two-lift cold joint preparation.

LIST OF TABLES

Approximate relation between water-cement ratio and strengths of concreteCoarse aggregate size groupsGrading of coarse aggregateDeleterious materials in coarse aggregates for airfield and heliport pavementsDeleterious materials in coarse aggregates for other pavementsGrading of fine aggregateDeleterious substances in fine aggregateSurface smoothness - airfield and heliport pavementsSelected characteristics of fiber-reinforced airfield pavementsInterim suggested maximum joint spacing for steel-fiber-reinforced concreteVibratory rollers used in RCCP construction

STANDARD PRACTICE FOR CONCRETE PAVEMENTS

1. Purpose. This manual provides information on thematerials and construction procedures for concretepavements.

2. Scope. This manual describes the constituents tobe used in concrete, the procedures to be used inmanufacturing concrete, and the equipment andprocedures to place, texture, and cure concrete forpavements.

3. Responsibilities, strength, and air content.

a. Responsibility for mixture proportioning. Theresponsibility for mixture proportioning must beclearly assigned to either the contractor or thecontracting officer in the project specifications.When the contracting officer is responsible formixture proportioning, he will approve all concretematerials as well as determine and adjust propor-tions of all concrete mixtures as necessary to obtainthe strength and quality of concrete required for thepavements. Cement will be a separate pay item inthe contract. When the contractor is responsible formixture proportioning, he will control all proportionsof the concrete mixture necessary to obtain thestrength and quality of the concrete required for thepavements, and cement will not be a separate payitem in the contract. However, the contracting officeris responsible for approving the quality of allmaterials the contractor uses in the concrete.

b. Approval responsibility. The contracting officeris responsible for approval of all materials, mixtureproportions, plants, construction equipment, andconstruction procedures proposed for use by thecontractor. The contractor must submit proposedmixtures if he is responsible for mixture propor-tioning; samples of all materials; and detaileddescriptions of all plants, construction equipment,and proposed construction procedures prior to thestart of construction.

c. Flexural strength. Structural designs are basedon flexural strengths that the concrete is expectedto obtain at 28 days for road pavements and 90 days

for airfield pavements. These ages are not adequatefor quality control in the field since a large amountof low-strength concrete could be placed beforestrength tests on samples revealed the problem.Correlations can be established between a 14-daystrength and the 28- or 90day strength used indesign, and this correlated 14-day strength can beused as a strength check for a more timely concretemixture control in the field.

(l.) Materials and flexural strength. To selectsuitable flexural strengths for the design ofpavements and for inclusion in contract specifica-tions, the contracting officer should have reliableinformation regarding flexural strengths obtainablewith acceptable concrete materials which are availablein the vicinity of the project. Typical design valuesfor flexural strength of paving-quality concretevary from 500 to 750 pounds per square inch (psi).Numerous tests indicate considerable variation inthe flexural strength of concrete when differentaggregates or different cements are used. There aresome indications that aggregate shape and modulusof elasticity are relatively more important inconcrete flexural strength than in compressivestrength. Also, after optimum flexural strength isreached, there usually is little increase in strength,even with a large increase in cement content. Mixtureproportioning studies will be made in accordancewith ACI 211.1 (see app A for referenced publications)to determine the flexural strengths to be used forthe design of the project. The water-cement ratio-strength relations for mixture proportioning in ACI211.1 are given in terms of compressive strength.Table 1 gives some approximate guidance forrelating the concrete modulus of rupture to thecompressive strength-water cement ratio relation-ships given in ACI 211.1. All aggregates, cementitiousmaterials, and admixtures used in the mixtureproportioning studies will be representative ofmaterials available for use in pavement construction.In selecting a flexural strength for pavement design,suitable allowance will be made for variations instrength indicated by tests of different combina-tions of aggregate and cement. Pavement designwill be based on a realistic and economical strengthobtainable with available materials.

1

Table 1. Approximate relation between water-cement ratio and strengths of concrete (modified from ACI 211.1)

(eq 1)

TM 5-822-7/AFM 88-6, Chap. 8

characteristics of freshly mixed concrete and isrequired for the freezing and thawing resistance ofhardened concrete. The use of entrained air inconcrete will reduce strength, but because of theimproved workability in the freshly mixed concrete,adjustments in aggregate proportions and reductionof water are normally possible that will negate or atleast minimize the loss of strength. Proper propor-tioning and control of the air-entrained concretemixture are essential in order to derive maximumbenefits from improvement in the placability anddurability of concrete with a minimum effect onflexural strength.

(2.) Percentage of air content. The specified aircontent will be 6 1 percent for concretepavements located in regions where resistance tofreezing and thawing is a prime consideration, andwill be 5 1 percent for concrete pavementslocated in regions where frost action is not a factorand air entrainment is used primarily to improve theworkability and placability of freshly mixed concrete.Air content will be controlled in the field at the pointwithin the specified range most appropriate for localconditions depending upon the severity of exposureand the quality and maximum size of aggregate. Ifslag aggregate is used, the air content will be deter-mined by the volumetric method as described inASTM C 173. Where the aggregate is of compara-tively poor quality or when the maximum size is 1%inches or less, the air content will be controlled at 6 1 percent. In such instances, where resistance tofreezing and thawing is not a prime consideration,the air content will be 5 1 percent. If furtherreduction in the air content or the use of non-air-entrained concrete is necessary, prior approval willbe obtained from HQDA (DAEN-ECE-G), Wash-ington, DC 20314-1000 or the appropriate Air Forcemajor command.

e. Cement content. Either the contractor or thecontracting officer may be responsible for mixtureproportioning. When the contractor is responsiblefor mixture proportioning, no separate payment willbe made for cement. When the contracting officer isresponsible for mixture proportioning, no limits forthe quantity of cement content will be included inthe contract specifications; the quantity of cementused per cubic yard of concrete will be determinedby the contracting officer, and cement will be paidfor under a separate bid item. When the concreteproposed for use on a paving project has a cementcontent of less than 470 pounds per cubic yard, priorapproval will be obtained from HQDA (DAEN-

ECE-G) or the appropriate Air Force major command.When concrete proportioning is the responsibility ofthe contractor and the cement content is less than470 pounds per cubic yard, the results should beverified by two Corps of Engineers Divisionlaboratories or commercial laboratories prior tosubmittal. The results of mixture proportioningstudies for proposed aggregates and cements andthe results of qualitative tests on aggregates and onresulting concretes will be submitted with requestsfor approval.

4. Cement.a. Five portland cements designated as Types I

through V are marketed today. ASTM C 150 providesa detailed specification for these cements. Type Iportland cement is common or ordinary cement thatis supplied unless another type is specified. Type IIis modified portland cement that provides moderateresistance against sulfate attack and a lower heat ofhydration than Type I cement. It is common forcement to be manufactured to meet the physical andchemical requirements of both Type I and II cements.

b. Type III cement is high early-strength cement.Ultimate strength is about the same as Type Icement, but Type III cement has a 3-day compressivestrength approximately equal to the Type Icements 7-day strength. The cost of Type IIIcement in lieu of Types I or II cement can only bejustified when early strength gain is needed to openpavements to traffic or the high heat of hydration isneeded for cool construction periods. Type IVcement has a low heat of hydration that may beuseful in mass concrete but is not likely to beencountered in pavement construction. Type Vsulfate-resistant cement should be used when theconcrete will be exposed to severe sulfate attack.The potential for severe sulfate attack exists whenthe concrete is exposed to water-soluble sulfate insoil or water in excess of 0.20 percent or 1,500 partsper million. The potential for moderate sulfateattack exists for sulfate contents in excess of 0.10,or 150 parts per million.

c. High alumina cement, also known as aluminousor calcium aluminate cement, gains most of itsstrength in one day, has a high exotherm, is resistantto chemical attack, and is a refractory material.When exposed to warm, moist conditions, it willundergo a long-term strength loss. High aluminacement may find some specialized applications inpavement construction where its rapid strengthgain, high exotherm, or refractory properties

3

TM 5-822-7/AFM 88-6, Chap. 8

outweigh its cost and long-term strength loss.d. There are also some expansive cements,

designated as Types K, M, and S in ASTM C 845,that may find some application where concreteshrinkage needs to be minimized or avoided.However, there is little experience with thesecements, and they will require careful investigationbefore use in pavement construction.

e. At least one United States manufacturer isactively promoting a slag cement made by grindingiron blast furnace slag. This may be substituted forup to 50 percent of the portland cement in a pavementmixture if tests show the required final propertiesare achieved in the hardened concrete. Preblendedmixes of portland-pozzolan (Type IP), and portland-slag cements (Type IS) are described in ASTM C 595and are acceptable for use in pavements.

5. Aggregates.a. Approval of aggregates. The contractor will use

aggregates from approved sources. If the contractorproposes to use aggregates from an unapprovedsource, the Government will be responsible forconducting tests to determine whether the proposedaggregates will meet the requirements of the project.Sampling and aggregate delivery costs will be borneby the contractor. The contract specifications willstate aggregate sample size, delivery location, andrequired evaluation time for the proposed aggre-gates. For small jobs requiring 1,600 cubic yards orless of concrete, all tests for aggregates from anunapproved source will be done by the contractor.

b. Quality. Aggregates must generally meet therequirements of ASTM C 33, as modified in thefollowing paragraphs. These requirements can beadjusted as necessary to reflect local experiencewith specific aggregates to insure economical use ofaggregates to meet project requirements. Themagnesium or sulfate soundness test (ASTM C 88)required in ASTM C 33 has not been consistentlysuccessful in identifying frost-resistant aggregate.Consequently, if an otherwise suitable aggregatefails this test, it should be further investigatedusing freezing and thawing tests as described inASTM C 666 or ASTM C 682 before it is finallyrejected. Similarly, if an otherwise suitable aggre-gate fails the Los Angeles (LA) abrasion test(ASTM C 131 or C 535), it can be accepted if it has ahistory of local use showing that it can be processedwithout unacceptable degradation and that it isdurable under weathering and traffic conditions

comparable to the project under investigation.c. Recycled concrete as aggregate. Existing

concrete may be taken up, crushed to suitablegradation, and re-used as concrete aggregate. Itmust meet all the requirements for gradation andquality that conventional aggregates must meet.All reinforcing steel should be removed. Duringcrushing, hammermill secondary crushers tend toproduce excess fines and should not be used. Therecycled concrete aggregates will not normallyrequire washing unless they have been contaminatedwith base or subgrade material. If the original pave-ment that is being recycled is D-cracked, then theconcrete should be crushed to a maximum size of inch. When crushed concrete is being used as fineaggregate, the inclusion of some natural sand maybe required to improve the new concrete mixturesworkability.

d. Alkali-aggregate reactions. Minerals in someaggregates can chemically react with the cementalkalis, resulting in an increase in volume thatplaces the concrete under expansive stresses whichmay result in map cracking, popouts, strength loss,and concrete expansion. Once started, the reactionand the resulting progressive deterioration of theconcrete cannot be stopped. These reactions aregenerally associated with aggregates containingpoorly ordered forms of silica, such as opal,chalcedony, chert, or flint (alkali-silica reaction),complex layer-lattice, and silicate minerals such asgraywackes, phyllites, siltstones, or argillites (some-times differentiated as alkali-silicate reaction), orargillaceous, dolomitic limestone (alakali-carbonatereaction). A petrographic investigation in conjunctionwith results of tests in accordance with ASTM C 227for alkali-silica expansion and ASTM C 586 foralkali-carbonate expansion is the most promisingapproach for identifying these problems. If possible,reactive aggregates should be avoided. If they cannotbe avoided, low-alkali cement should be specified. Iflow-alkali cement is not available or is overly expen-sive, some pozzolans and slag cements have beensuccessful in countering alkali-silica reactions, orreactive aggregate may be blended with non-reactiveaggregate to lessen the effect of the reactions.

e. Coarse aggregate.(l.) Composition. Coarse aggregate may be

natural gravel, crushed gravel, crushed stone, crushedrecycled concrete, or iron blast furnace slag. Thecrushing of gravel tends to improve the quality andthe bond characteristics and generally results in ahigher flexural strength of concrete than if uncrushed

4

TM 5-822-7/AFM 88-6, Chap. 8

gravel is used. When mixture proportioning studiesor local experience indicates that a low flexuralstrength will be obtained with uncrushed gravel, thepossibility of obtaining higher strength by crushingthe gravel will be investigated. Elongated particleswith a widthto-thickness ratio in excess of 3 maynot exceed 20 percent by weight as determined byCRD-C 119. This requirement attempts to avoidintroducing structural planes of weakness in thefinished concrete, workability problems associatedwith an excess of particles of these shapes, anddurability problems that may develop if air andwater are trapped under flat and elongated particles.

(2.) Size and grading. The maximum size of thecoarse aggregate used in pavement concrete shouldnot exceed one-fourth of the pavement thickness. Inno case will the coarse aggregate exceed a 2-inchmaximum size. However, for pavement constructionin areas where aggregate popouts have been a problemor may occur, the coarse aggregate will not exceed1-inch nominal maximum size. In areas where

D line cracking in pavements has been a problem,limestone aggregates should not exceed -inchnominal maximum size and should be of low absorp-tion. When the nominal maximum size of coarseaggregate is greater than 1 inch, the aggregatesshall be furnished in two size groups as shown intable 2, with gradings within the separated sizegroups conforming to the requirements of table 3.Where local practice provides size-group separationsother than as shown in table 2, local size gradingsmay be specified if approximately the same sizeranges are obtained and the grading of coarse aggre-gate when combined and batched for concrete is asrequired by mixture proportioning. For projectsrequiring 1,600 cubic yards or less of concrete,special grading requirements for coarse aggregateaccording to local practice may be substituted forthe gradings shown. Local State Department ofTransportation specifications for gradings may beused for those jobs requiring 1,600 cubic yards orless of concrete.

Table 2. Coarse aggregate size groupsL

Nominal Maximum Size Size Groups

1 in. No. 4 to in. in. to 1 in.

2 in. No. 4 to 1 in.1 in. to 2 in.

5

TM 5-822-7/AFM 88-6, Chap. 8

Table 3. Grading of coarse aggregate

S i e v e S i z eU . S . S t a n d a r d

Square Mesh

P e r c e n t a g e b y W e i g h t P a s s i n g I n d i v i d u a l S i e v e sNo. 4 to3 / 4 i n .

No. 4 to1 in .

3 / 4 i n . t o 1 in. to2 in .1 - 1 / 2 i n .

2 - 1 / 2 i n .

2 in .

1 - 1 / 2 i n .

1 in .

3 / 4 i n .

1 / 2 i n .

3 / 8 i n .

No. 4

No . 8

100

9 7 3

50 20

7 7

- - - - - -

100- - - -

100

9 7 3100

9 5 5 - -

- - - -

3 3- - - -

- - - -

- - - -

(3.) Deleterious substances.(a) Pavements used by aircraft. Table 4 lists

the common deleterious substances and specifieslimits for these materials. The performance history

waive table 4 requirements for Air Force pavements.Upon request, the AFRCE and the using commandwill be furnished available engineering informationon local aggregates and behavior records on pave-ments made from them. A copy of the instructionsand the revised requirements will be furnished forinformation to the HQDA (DAEN-ECE-G) orAFESC as applicable. In the case of Air NationalGuard and Army pavements, the using commandwill be furnished information on the costs of aggre-gates complying with specification requirementsand on less costly local aggregates along withbehavior records on pavements made with localaggregates. However, requirements will be waivedonly if requested by the Air National Guard BaseDetachment Commander or the Army InstallationCommander with his assurance that operationalrequirements will be satisfied by a performance thatis equal to that of existing pavements constructedwith these less costly aggregates. Requests will besubmitted for approval to HQDA (DAEN-ECE -G)with proposed specification requirements, compara-tive cost estimates, and evidence that operationalrequirements will be satisfied.

of local aggregates contributing to pavementdefects will be the determining factor in setting thelimits for deleterious substances. The limits areintended to eliminate popouts and weatherouts inairfield pavements. Other deleterious substancesknown to contribute to popouts will be identified bythe contracting officer, and suitable limits will bespecified. Calcium oxide (CaO) and magnesium oxide(MgO) or a mixture thereof, in lumps, representingthe hard burned oxides from fluxing stone or refrac-tory brick should be added to the list of deleterioussubstances if air-cooled blast furnace slag is used asthe aggregate. Since the types of materials producingpopouts will vary for different areas, some adjust-ments of the limits may be desirable for individualprojects. Reductions in specified limits may bemade as necessary, but increases to permit the useof local aggregates that have an acceptable experiencerecord will be governed by the following procedures.Air Force Regional Civil Engineers (AFRCE) havebeen authorized to instruct division engineers to

6

TM 5-822-7/AFM 88-6, Chap. 8

Table 4. Deleterious materials in coarse aggregates for airfield and heliport pavements.

Areas with Areas withMajor Popouts Minor Popouts

Severe a Moderate a Severe a Moderate a

Materials Weather Weather Weather Weather

Clay lumps 0.2 0.2 2.0 2.0

Shaleb 0.1 0.2 1.0 1.0

Material finer 0.5 0.5 1.0 1.0than No. 200 sievec

Lightweight particles 0.2 0.2 0.5 0.5

Clay ironstone 0.1 0.5 1.0 1.0

(Continued)

aSevere, moderate, and mild weather are defined as follows:

Air Freez- Average Precipitation for a Singleing Index Month During Period--1 Month Before

Weather for Coldest Average Date of First Killing FrostSeverity Year in 30* to Average Date of Last Killing Frost

Moderate 500 or less Any amount

Moderate** 501 or more Less than 1 inch

Severe 501 or more 1 inch or more

* Calculated as described in TM 5-818-2/AFM 88-6, Chapter 4.** In poorly drained areas, the weather should be considered severe

even though the other criteria indicate a rating of moderate.

b Shale is defined as a fine-grained thinly laminated or fissile sedimentary rock.It is commonly composed of clay or silt or both. It has been indurated by compac-tion or by cementation, but not so much as to have become slate.

cLimit for material finer than No. 200 sieve will be increased to 1.5 percent forcrushed aggregates if the fine material consists of crusher dust that is essen-tially free from clay or shale.

d The separation medium shall have a specific gravity of 2.0. This limit does notapply to coarse aggregate manufactured from blast-furnace slag unless contaminationis evident.

e Clay ironstone is defined as an impure variety of iron carbonate, iron oxide,hydrous iron oxide, or combinations thereof, commonly mixed with clay, silt, orsand. It commonly occurs as dull, earthy particles, homogeneous concretionarymasses, or hard shell particles with soft interiors. Other names commonly used forclay ironstone are chocolate bars and limonite concretions.

7

TM 5-822-7/AFM 88-6, Chap. 8

Areas with Areas with

Materials

Chert and/or chertystone (less than

2.50 sp. gr. SSD) f

Claystone, mudstone,

and/or si ltstone g

Shaly and/or argilla-h

ceous limestone

Other soft particles

Total of al l deleteri -ous substancesexclusive of mate-rial finer thanNo. 200 sieve

Major Popouts Minor Popouts

Severe a Moderate a Severe a Moderate a

Weather Weather Weather Weather

0.1 0.5 1.0 5.0

0.1 0.1 1.0 1.0

0.2 0.2 1.0 2.0

1.0

1.0

l .0

2.0

1.0

3.0

2.0

5.0

f Chert is defined as rock composed of quartz, chalcedony, or opal, or any mixtureof these forms of silica. It is variable in color . The texture is so fine thatthe individual mineral grains are too small to be distinguished by the unaided eye.Its hardness is such that it scratches glass but is not scratched by a knife blade.It may contain impurities such as clay, carbonates, iron oxides, and other min-erals. Other names commonly applied to varieties of chert are flint, jasper,agate, onyx, hornstone, porcellanite, novaculite, sard, carnelian, plasma, blood-stone, touchstone, chrysoprase, heliotrope, and petrified wood. Cherty stone isdefined as any type of rock (generally limestone) which contains chert as lensesand/or nodules or irregular masses partially or completely replacing the originalstone. SSD = saturated surface dry.

gClaystone, mudstone, or siltstone is defined as a massive fine-grained sedimentaryrock which consists predominately of clay or silt without lamination or fissility.It may be indurated either by compaction or by cementation.

h Shaly limestone is defined as a limestone in which shale occurs as one or morethin beds of laminae. These laminae may be regular or very irregular and may bespaced from a few inches down to minute fractions of an inch. Argillaceous lime-stone is defined as a limestone in which clay minerals occur disseminated in thestone in the amount of 10 to 50 percent by weight of the rock; when these make upfrom 50 to 90 percent, the rock is known as calcareous (or dolomitic) shale (orclaystone, mudstone, or siltstone).

TM 5-822-7/AFM 88-6, Chap. 8

(b) Other pavements. For other pavements, be identified by the contracting officer, and suitablethe limiting amounts of deleterious substances in limits will be specified and materials defined wheneach size of coarse aggregate will be specified as necessary.shown in table 5. Other deleterious substances will

Table 5. Deleterious materials in coarse aggregates for other pavements

Material Percentage by Weight

Clay lumps and friable particles 2.0

Material finer than No. 200 sieve a 1.0

L i g h t w e i g h t p a r t i c l e s 1.0

Other soft particles 2.0

Note:

aLimit

The total of all deleterious substances shall not exceed5.0 percent of the weight of the aggregate. The percentageof material finer than No. 200 sieve shall not be includedin th i s t o ta l .

for material finer than No. 200 sieve will be increased to1.5 percent for crushed aggregates consisting of crusher dust thatis essentially free from clay or shale.

bThe separation medium shall have a specific gravity of 2.0. This

limit does not apply to coarse aggregate manufactured from blast-furnace slag unless contamination is evident.

(4.) Slag aggregate. Iron ore blast-furnace slagaggregates vary widely in properties depending onthe manufacturing and cooling processes used. Un-aged blast-furnace slag may contain free lime, butaging reduces this to acceptable levels. Properly agediron ore blast- furnace aggregate has a good historyof performance. Slag from steel mills, however, isnot acceptable as concrete aggregate because of thevarious oxides it contains.

f. Fine Aggregate.

(l.) Composition and shape. Requirements forcomposition and particle shape of fine aggregate arepurely descriptive, for example, natural and/ormanufactured sand, spherical or cubical, and nolimits are shown. A limit will be included for flat andelongated particles in fine aggregate, comparablewith the limit specified for coarse aggregate, whentests indicate that poor particle shape will affect the

workability and quality of the concrete. Shape willbe determined in accordance with CRD-C 120.

(2.) Grading, uniformity of grading, anddeleterious substances. The grading and uniformityof grading specified in table 6 for fine aggregate aredesirable for pavement concrete and can generallybe met at a reasonable cost within the continentalUnited States. However, if conformance with theserequirements will result in undue construction costsand if investigation of the available sources of fineaggregate in the locality indicates that limits otherthan specified are desirable, a request will be sub-mitted to HQDA (DAEN-ECE-G) giving completeresults of all tests conducted to substantiate thatconcrete of comparable workability, durability, andstrength can be produced without an increase incement content. The amount of deleterioussubstances in the fine aggregate shall not exceed thelimits shown in table 7.

9

TM 5-822-7/AFM 88-6, Chap. 8

Tabk 6. Gnading of fine aggregate

Sieve Size, Cumulative Percentage by WeightU. S. Standard Square Mesh Passing Individual Sieves

3 /8 in . 100

No. 4 9 7 2 3

No. 8 8 5 2 5

No. 50 20 10

No. 100 6 4

Note: In addition, the fine aggregate, as delivered to the mixer,shall have a fineness modulus of not less than 2.40 normore than 2.90. The grading of the fine aggregate alsoshall be controlled so that the fineness moduli of at leastnine of ten samples of the fine aggregate as delivered tothe mixer will not vary more than 0.15 from the averagefineness moduli of all samples previously taken. Thefineness modulus shall be determined by CRD-C 104(Appendix A).

Table 7 Deleterious substances in fine aggregate

Material Percentage by Weight

Clay lumps and friable particles 1 . 0

Material finer than No. 200 sieve 3 . 0

Lightweight particles 0 . 5

Note: The total of all deleterious materials shall not exceed 3.0 percent of the weight of the aggregate.

10

TM 5-822-7/AFM 88-6, Chap. 8

g. Aggregate for calibration hardstands. To avoidinclusion in the pavement concrete of iron oxides orother iron-rich materials having magnetic propertiesthat will interfere with the operation of the facility,the concrete aggregate proposed for paving calibrationhardstands will be subjected to detailed petrographicanalyses in accordance with ASTM C 295 prior toacceptance. Special attention will be given to theexistence of magnetite in granites, high-ironminerals in traprock, pyrite in limestone, and freeiron or iron oxide in slag aggregate. When a list ofaggregate sources is included in the contract specifi-cations, the sources not approved for concrete usedin calibration hardstands will be indicated.

h. Aggregate for power check pads. Concrete thatwill be exposed to extended jet engine blast duringmaintenance can use igneous rocks with a low silicacontent and a high content of ferromagnesianminerals or slag as aggregate to improve its perfor-mance under high temperature. Aggregates rich insilica such as quartzite or chert should be avoided.Aggregate with a high silica content such as sand-stone or granite, especially if coarse grained, cancause problems. Calcareous aggregates such as lime-stone or dolomite are acceptable.

6. Admixtures.a. Admixtures are used to modify properties of

fresh or hardened concrete. Admixtures may be usedto improve workability, control initial set, reduceheat generation, accelerate strength gain, increasestrength, and improve durability. Seven chemicaladmixtures are listed for use in portland cementconcrete in ASTM C 494, as follows: Type Awater-reducing admixture; Type B retarding admixture;Type Caccelerating admixture; Type Dwater-reducing and retarding admixture; Type Ewater-reducing and accelerating admixture; Type Fwater-reducing, high-range admixture; and TypeGwater-reducing, high-range and retardingadmixture.

b. Air-entraining admixtures provide resistanceto freezing and thawing and should meet therequirements of ASTM C 260, and will normally berequired in all concrete for pavements. For smalljobs under 1,600 cubic yards, air-entrainingcements may be considered. The use of any otheradmixture will depend on the economics of its useand site conditions. The effect of an admixture willvary, depending on conditions such as cement type,specific mixture proportions, ambient temperature,or water quality. Furthermore, an admixture may

affect several qualities of the concrete, and somedesirable properties may be adversely affected.Consequently, the decision to use an admixturemust be based on experience and tests with thecement, aggregates, and admixtures representativeof those to be used on the project. It must be demon-strated that the final concrete proposed pavementquality is not adversely affected by the use of anyproposed admixture. More extensive guidance onadmixtures is provided in ACI 212.lR and ACI212.2R.

7. Pozzolans.a. Pozzolans are defined in ASTM C 618 as

siliceous or siliceous and aluminous materialswhich in themselves possess little or no cementitiousvalue, but will, in finely divided form and in thepresence of moisture, chemically react with calciumhydroxide at ordinary temperatures to formcompounds possessing cementitious properties.This ASTM specification recognizes three classes ofpozzolan and provides detailed requirements foreach class. Class N pozzolans are raw or calcinednatural pozzolans such as some diatomaceous earths,opaline cherts, tuffs, volcanic ashes, clays, andshales. Fly ash is divided into two classes. Class F isfly ash produced by burning anthracite or bituminouscoal, and Class C fly ash is produced by burning ligniteor subbituminous coal. Environmental ProtectionAgency (EPA) guidelines published in 1983 (40CFR, Part 249) require that the use of fly ash mustbe allowed on all federal projects unless it can beproven technically unsuitable.

b. Pozzolans may be substituted for a maximumof 25 percent by volume of portland cement in concretefor pavements. If substitution of pozzolan abovethis limit is contemplated, a thorough test programmust show that the proposed substitution limit willnot adversely affect workability, admixture perfor-mance strength, and durability of the final concrete.Pozzolans typically have specific gravities appreciablylower than portland cement, and pozzolan limits areexpressed as a percent of the volume of cementitiousmaterials. In general, concrete containing pozzolanshas improved workability, lower heat of hydration,and a slower strength gain. When pozzolans are tobe used, the required time to gain the design strengthmay be increased beyond the standard 28 days forroads and streets and 90 days for airfield pavementsto the extent that the concrete is not to be exposedto traffic.

c. Class N pozzolans will not generally be

11

TM 5-822-7/AFM 88-6, Chap. 8

encountered in pavement construction. The use offly ash, however, is becoming increasingly common.Fly ash produced by industrial burning of coal tendsto be highly variable, depending on factors such asemission controls, load, and boiler design. Thisproduction variability is compounded further by thenatural variability of lignite and subbituminous coalthat produce Class C pozzolan. Also, Class Cpozzolans have poor resistance to sulfate attack,and some have high alkali contents that may contri-bute to alkali aggregate reaction. Specifications forpozzolans should require that the ASTM C 618specification be modified to require a maximum losson ignition of 6 and 8 percent, respectively, for ClassF and N pozzolans and a minimum pozzolanic activityindex with lime of 900 psi at 7 days. Mixture propor-tioning studies should use the same pozzolans andcements that will be used on the project and mustdetermine that the final concrete characteristics,strength gain, and durability are adequate.

8. Miscellaneous materials.a. Other materials used in concrete pavement

construction including curing materials, dowels, tiebars, reinforcement, and expansion-joint filler arecovered by applicable specifications. When concreteis required to be free of magnetic materials, specialinstructions will be obtained from HQDA (DAEN-ECE-G) for the selection of dowels, tie bars, andreinforcement. Aluminum will not be used in concretepavements.

b. Field welding of crossing bars (tack welding) isprohibited. All welded splices will conform to therequirements of the American Welding Society (AWS)D 1.4. Selection of the proper welding proceduredepends on the actual chemical composition of thesteel. A procedure suitable for one chemical compo-sition can be totally unsuited for another compositionof the same strength grade. It is essential that thecomposition of the steel to be welded be determinedbefore the welding procedure is established. Wherereinforcing bars are to be ordered for new work, thefabricator should be informed that welded splicesare contemplated. The fabricator can provide thechemical composition of the reinforcing bars and inmany cases can provide bars that are more suited towelding.

c. Epoxy-coated reinforcing steel and dowel barsare being used more frequently in areas such asbridge decks, coastal areas, and pavements subjectto heavy applications of de-icing salts to minimizepotential corrosion problems. If these materials are

used, they should conform to ASTM A 775. Epoxy-coated dowels and reinforcing steel will rest onepoxy-coated wire bar supports or on bar supportsmade of dielectric material. Wire bar supports willbe coated for a minimum of 2 inches from the pointof contact with the epoxy-coated reinforcing bars.Adequate ventilation to dissipate fumes must beprovided if epoxy-coated steel is welded.

d. Appendix C describes the materials andmethods used for the construction of steel fiberreinforced concrete.

9. Water. Water for mixing concrete will be free frommaterials that affect hydration of the cement.Potable water may be used without testing however,tests will be made in accordance with CRD-C 400 ifthe water source is a stream or another body ofwater of unknown quality. Seawater has been usedsuccessfully as mixing water, but this should onlybe done if there is no feasible alternative. There maybe up to a 15 percent loss in ultimate strength, settimes may be affected, and surface efflorescencemay occur. The risk of steel corrosion maybe increased,so the use of coated dowels and reinforcing steelshould be considered if seawater is to be used.

10. Sampling and testing of materials.a. Cement. Cement to be used in pavements for

aircraft traffic will be sampled and tested. Cementmeeting all other test requirements may be acceptedprior to the required 7-day age when the strength isequal to or greater than the 7-day strength require-ment. Cement for pavement projects requiring 1,600cubic yards or less of concrete may be accepted onthe basis of the manufacturers certified mill testreports showing compliance with cited cementspecifications.

b. Aggregates.(l.) Listed sources. Listing of aggregate sources

will be based on a thorough investigation to determinethat suitable aggregates are obtainable for theproposed use. Evaluation of the material will requirecomplete laboratory testing including petrographicexaminations, physical tests, durability tests, andalkali-reactivity tests. The service record of aggre-gates will be determined by inspecting structuresthat have had exposure equivalent to the proposedstructure. When an aggregate source has been listedpreviously for use on the basis of a complete investi-gation, additional similar use of the source within aperiod of 3 years may be permitted on the basis ofpetrographic examinations and limited physical

12

TM 5-822-7/AFM 88-6, Chap. 8

tests if the results show no change in the compositionand quality of aggregate. For proper design andpreparation of plans and specifications, it isnecessary to investigate and determine suitableaggregate sources and concrete strengths obtainablewith aggregates. It is essential that these investiga-tions be conducted as early as possible during projectplanning.

(2.) Sources for calibration hardstands. Whencontract specifications cover the paving of calibrationhardstands, the list of sources will indicate whichsources are approved for such work.

(3.) Aggregate sources not previously listed.When the contractor proposes aggregate from asource not previously listed, the evaluation ofsamples of that aggregate will include all testsnecessary to demonstrate that a concrete producedfrom the materials will have quality and strengthcomparable with that of concrete made with aggre-gate from the approved sources listed. When thecontracting officer is responsible for mixtureproportioning and cement is a separate pay item inthe contract, aggregates of good quality that requirean increase in the quantity of cement over thatrequired by aggregates from listed sources to produceconcrete of the specified flexural strength will beapproved for use only if the contractor agrees inwriting to pay for the additional cement required.

(4.) Unlisted source. When the contractspecifications do not include a list of approvedaggregate sources, the source(s) proposed by thecontractor will be investigated as soon as possibleafter the award of the contract.

(5.) Aggregates for a small project. Evaluationof aggregates from non-listed sources and concretemixture proportioning for projects requiring 1,600cubic yards or less of concrete, except for airfieldand heliport paving, will be performed by an approvedcommercial testing laboratory at no expense to theGovernment.

11. Delivery and storage of materials.a. Cement and pozzolan. Separate storage facilities

will be provided for each type of cementitiousmaterial. Storage facility will be thoroughly cleanedbefore changing the type of cementitious materialstored init. Storage facilities must be weather-tightand must be properly ventilated.

b. Aggregates.(l.) Control of grading. Aggregate-handling and

aggregate-storage facilities may vary greatly fordifferent projects, and only general requirements

can be specified. Grading and uniformity of gradingrequirements will be determined as the aggregatesare delivered to the mixer, and the contractor isresponsible for meeting these requirements. Carefulinspection of storage and handling operations,however, is desirable to assure satisfactory controlof the aggregate grading and to prevent contamin-ation by foreign material. Aggregate storage tech-niques that use coned piles or spread truck-dumpedaggregate with a bulldozer cause segregationproblems. Aggregates delivered by trucks are bestdumped and left in individual adjacent piles. A clamshell spreading aggregate in thin layers has alsobeen used to minimize segregation. Aggregateshould be handled as little as possible to minimizesegregation. Potential sources of contaminantsinclude windblown foundation and adjacentmaterials and contaminants from equipment used inhandling the aggregates.

(2.) Moisture control. Uniformity of freemoisture in aggregate is essential for proper controlof concrete consistency. A period of free-drainingstorage is required for fine aggregates and thesmaller size of coarse aggregate. Normally, 24 to 48hours will be sufficient. However, shorter or longertimes may be specified if the tests of time to reachan equilibrium so indicate.

12. Grade control. The lines and grades shown foreach airfield and heliport pavement category of thecontract shall be established and maintained bymeans of line and grade stakes placed at the jobsiteby the contractor. Elevations of all benchmarks usedby the contractor for controlling pavement operationsat the jobsite will be established and maintained bythe Government. The finished pavement grade linesand elevations shown shall be established andcontrolled at the jobsite in accordance with bench-mark elevations furnished by the contracting officer.The pavements shall be constructed to the thicknessesand elevations indicated. Provisions for line andgrade control for roads, streets, and open storageareas shall be included in the contract specifications.

13. Proportioning.a. Mixture proportioning. Before any concrete is

placed, trial mixtures will be prepared withmaterials from the sources to be used for productionof concrete on the project. When the contractor isresponsible for mixture proportioning, trial mixtureswill be prepared by a commercial testing laboratoryapproved by the contracting officer at no expense to

13

TM 5-822-7/AFM 88-6, Chap. 8

the Government, and the results will be submittedto the contracting officer for approval. When thecontracting officer is responsible for mixtureproportioning, trial mixtures will be prepared by theGovernment with materials supplied by the contractorfrom the sources to be used for production of concreteon the project. Mixtures will be made in sufficientnumber to establish optimum proportions of theaggregates and to represent a wide range in cementcontents and watercement ratios within specifiedrequirements for air content and workability. Thewater-cement ratio will not exceed 0.45 by weightfor pavement mixtures. After the final proportionsof the trial mixtures have been established, 6inchby 6-inch cross-section test/beam specimens fromeach mixture will be made in accordance withASTM C 192 and tested as described in ASTM C 78.A minimum of nine test specimens should be madeto establish the flexural strength of each mixture ateach test age. From these mixture proportioningstudies, the controlling maximum water-cementratio and hence the cement content required toproduce concrete of specified strength will be deter-mined. This same procedure will be used to establishnew mixture proportions when necessary because ofa change in the source or the character of the concreteingredients after concrete placement has started.

b. Mixture proportions.(l.) Contracting officer responsible for mixture

proportions. When the contracting officer is respon-sible for the mixture proportions, proportions of allmaterials used in the concrete mixture will be asdirected. The contracting officer will require suchchanges in the mixture proportions as necessary tomaintain the workability, strength, and qualityrequired by the contract specifications. The mixtureproportions determined by mixture proportioningstudies will be used in starting paving operations.Adjustments will be made by the contracting officeras necessary to establish the mixture proportionsbest suited for job conditions and materials used.Subsequent mixture adjustments will be made whennecessary, but usually these adjustments will be of aminor nature as required to compensate for variationsin gradings and the moisture content of the aggregate.

(2.) Contractor responsible for mixture propor-tions. When the contractor is responsible for themixture proportions, proportions of all materials usedin the concrete mixture will be as directed by thecontractor. The contractor will require such changesin the mixture proportions as necessary to maintainthe workability, strength, and quality required by

the contract specifications. The mixture proportions determined by mixture proportioning studies will beused in starting paving operations. Adjustmentswill be made by the contractor as necessary toestablish the mixture proportions best suited for thejob conditions and materials used. Project specifi-cations will require the contractor to notify thecontracting officer prior to making any change tothe approved mixture proportions and to indicatethe changes to be made. Changes to the mixtureproportions will be of a minor nature as required tocompensate for variations in gradings and themoisture content of the aggregate unless laboratorymixture studies for the new mixture are submittedfor approval.

c. Workability. The concrete slump shall not exceed2 inches. Within this maximum limit, the slump willbe maintained at the lowest practical value suitablefor prevailing weather conditions and for equipmentand methods used in placement of the concrete. Forsmall paved areas, slump in excess of 2 inches maybe permitted, but in no case will the slump exceed 3inches. The concrete slump will be determined in thefield by the method described in ASTM C 143. Slumpfor slipform paving of airfield and heliport pavementsshould be specified in a range of O to 1 inches.

d. Strength. Control of the strength of the concretemixture will be based on tests of concrete specimenstaken during the paving operations. Pavements tobe used by aircraft are designed on the basis of theflexural strength that the concrete is expected toattain at 90 days, and specimens will be tested atthis age for use in the evaluation pavements. Sincethe period necessary to obtain the 90-day fieldstrengths is too great to exercise proper control ofthe concrete during pavement construction, a 14-daystrength requirement will be included in the contractspecifications. Flexural-strength tests will be madeat 14 days to determine compliance with the 14-daystrength requirement. In addition, 7-day strengthtests will be made to provide an early indication ofthe concrete strength. The average strength at theage of 14 days of any five consecutive individual testvalues representing each concrete mixture will benot less than the specified strength at the age of 14days, and not more than 20 percent of the individualvalues will be less than the specified strength.Adjustments of the concrete mixture proportionswill be made as necessary to maintain this strengthcontrol. When sufficient 90-day strengths becomeavailable, further adjustment of the concrete mixturemay be made as necessary to assure that the 90-day

14

TM 5-822-7/AFM 88-6, Chap. 8

strength used for the design of the pavements will beobtained and that an economical mixture is being used.

14. Subgrade, base, forms, and string lines.a. General. The setting and protection of forms and

string lines and the final preparation of thesubgrade, base course, or filter course require closeattention to all details to assure that the pavementwill have the required thickness and the surface willbeat the required grade.

b. Subgrade. Subgrade is the natural soil or fillupon which the base and concrete pavement are placed.Special procedures may be necessary when dealingwith frost-susceptible soils, expansive soils, pumping-susceptible soils, lateritic soils, or organic soils.Removing soft or troublesome soils that occur inpockets may be desirable, where possible.

c. Base. A base may perform many functions, suchas drainage, construction platform, and structuralstrengthening of the pavement. A base may be agranular material or lime, cement, or an asphalt-stabilized material. Also a lean concrete, sometimesreferred to as Econocrete, is sometimes used as abase. There is no clearly accepted definition, butcement contents are typically lower, and sometimespoorer quality aggregates are used. The lean concretebase should meet the strength and durability require-ments of cement-stabilized materials and can betreated as a high-quality stabilized material indesign.

d. Form materials. Steel forms will be used for allformed pavement construction. Wood forms generallyare unsatisfactory for paving work, and their use willnot be permitted except for such miscellaneous areasas bulkheads and curved fillets. To avoid the excessivecost of pavement construction for small j ohs, woodforms may be allowed for pavements less than 8 inchesthick in noncritical areas, such as open storage areas,helicopter parking pads, and vehicle parking.

e. Construction of forms. Provisions relating tobuilt-up forms may be omitted from contract specifi-cations when the contract plans require constant slabdepth for each paved area. When this provision isretained in a contract specification, the contractor isrequired to furnish steel forms equal to the edgethickness of the majority of pavement slabs for eachpaved area. Built-up forms will be used only whereedge thicknesses exceed the basic form depth. Thebase width of built-up forms will be equal to thewidth required for a comparable full-depth form.Side forms on sl.ipform pavers will be the full depthof the pavement.

f. Placement of forms and string lines. Forms andstring lines should be installed well in advance ofconcrete paving operations so that the requiredchecks and necessary corrections can be madewithout stopping or hindering concrete placement.The same reasoning applies to the final preparationof the underlying material, which should not be lessthan one full days operation of the paving equip-ment ahead of paving.

g. String line. The string line will be of high-strength cord or wire. The choice will depend on thetype of automatically controlled slipform paver used.Certain manufacturers recommend that high-tensile-strength wire be stretched tautly between supports.Other manufacturers recommend a large-diametercord and do not require the tautness that is recom-mended for the wire. The use of wire requires firmlyanchored supports. As a result, the wire is less likelyto be disturbed than is the cord whose supports donot have to be so firmly anchored. The wire isdifficult to see, and flagging should be attachedbetween the supports to reduce the chance that itwill be disturbed during construction. The cord doesnot require supports to be as firmly anchored as forthe wire, and as a result, the cord is easier to installand maintain. However, the chance of sagging betweenthe supports is greater. The cord is easy to see, andas a result, the chances of its being knocked out ofalinement are less than for the wire. However, thecord is more easily disturbed than the wire andshould be checked frequently.

h. Removal of forms. Pavement forms generallymay be removed 12 hours after the concrete is placed.A longer period will be necessary when the strengthgain of the concrete is retarded because of delayed orinadequate protection during cold weather. In someinstances, earlier removal of forms maybe permittedso that the transverse joints may be sawed completelythrough to the edge of the slab without leaving asmall fillet of concrete adjacent to the form.

15. Batching and mixing.a. General. There are three types of plants: auto-

matic, semi-automatic, and manual. For pavingprojects, either automatic or semi-automatic plantswill be acceptable. Specifications will be prepared toallow either type of plant, and the contractor willhave the option as to the type of plant to be used.

b. Plant capacity. The capacity to be specified forthe batching plant and mixing equipment will bedetermined in accordance with the concrete-placementrequirements for the project. Since the pavement

15

TM 5-822-7/AFM 88-6, Chap. 8

slabs are comparatively small, the plant capacitygenerally will not be influenced by any requirementsfor maintaining the concrete in a plastic conditionduring placement. The main considerations will bethe required placing schedule to meet the completiondate for the construction or, when slipform paversare used, the required amount of concrete to maintaina uniform forward movement of the paver of not lessthan 2.5 feet per minute. However, the placementrate specified for pavements constructed during hotweather should also be considered in determiningplant capacity requirements.

c. Concrete mixers. Mixers having a capacity of at least 5 cubic yards of mixed concrete are required forairfield paving projects, but smaller mixers may bepermitted for small road projects and other smallmiscellaneous construction. Contract specificationsfor jobs of suitable size and location will include anoption for the contractor to reduce mixing time duringprogress of work from the mixing time required atthe start of the job on the basis of mixer performancetests in accordance with CRD-C 55, provided thefollowing requirements are met at all times:

Weight per cubic foot of mortar calculated to an air-free basis, lb/ft3

Air content, volume percent of concrete

Slump, inches

Coarse aggregate content, portion by weight of eachsample retained on No. 4 sieve, percent

Average compressive strength at 7 days for eachsample based on average strength of all test speci-mens, percent 10.0

Water content, portion by weight of each samplepassing No. 4 sieve, percent 1.0

Parameters Tested For: Requirement, expressed as maximum permissiblerange in results of tests of samples taken from threelocations in the concrete batch

1.0

1.0

1.0

6.0

In addition, no reduction in mixing time will beallowed if it results in a reduction in the 7-dayflexural strength from the average strength of fiveconsecutive sets of specimens made from batchesmixed the full time. The requirements for stationarymixers and truck mixers will be included unless it isdetermined that concrete complying with the specifi-cations cannot be manufactured by these types ofmixers. Truck mixers often have difficulty indischarging the comparatively low-slump concretemixtures required for airfield pavement construction,therefore, truck mixers should comply with ASTM C94. The tendency of the concrete to hang up indischarge chutes may cause delays, which frequentlylead to requests by the contractor that the concreteslump be increased. This difficulty also may occurwith vehicles used for hauling concrete to formswhen stationary mixers are used. The slump ofready-mix concrete will not be increased because of

16

the inadequacy of the mixing or transportationequipment to mix and discharge the concrete.

d. Approval of mixers. Before truck mixers orstationary mixers are approved for use, carefulconsideration will be given to the proposed plant andfacilities for storage and handling of materials, andfor batching, mixing, transporting, and handling ofconcrete at the jobsite to assure that adequate controlof the concrete can be exercised. When truck mixersare used with a long haul between the batching plantand the project, adequate control of the concretemay be difficult due to variations in slump and aircontent caused by differences in mixing time. Insuch cases, it will be necessary to require that mixingbe done after the mixer trucks arrive on the job.Truck mixers will not be permitted for mixing concreteon slipform construction. Truck mixers shall beequipped with accurate revolution counters. Ingeneral, truck mixers should only be used on jobs

TM 5-822-7/AFM 88-6, Chap. 8

requiring 2,500 cubic yards of concrete or less.e. Transporting plant-mixed concrete. Vehicles for

transporting concrete from stationary mixers to theforms will conform to the applicable requirements ofASTM C 94. Plant-mixed concrete may be trans-ported in a truck agitator, in a truck mixer operatingat agitating speed, or in approved non-agitatingequipment. Non-agitating equipment will havesmooth, watertight, metal bodies equipped withgates to permit control of the discharge of theconcrete; covers will be provided for protectingconcrete in transit, as required. Concrete transportedin non-agitating equipment will be discharged intothe pavement forms or to the slipform paver within45 minutes after introduction of the mixing waterand cement to the aggregates at the mixer. Themajor problem in using ready-mixed concrete inpavement construction is avoiding segregation indischarging and transferring the concrete from thetransporting unit to the final position in the form oron the subgrade in front of the slipform paver. Theuse of readymixed concrete requires suitabletransfer and spreading equipment capable ofdepositing and distributing the concrete in anunsegregated condition in the final position in theforms. When low-slump plant-mixed concrete istransported, trucks equipped with vibrators areoften required to discharge the concrete and shouldbe required unless it is satisfactorily demonstratedthat the concrete can be discharged without delay.

16. Placing.a. General. Concrete may be placed between fixed

forms or using approved slipform paving equipment.Both methods produce satisfactory results, andwhen possible, the option should be left with thecontractor as to the method to be used. Withslipform equipment, the rate of placement can besignificantly increased over the rate with fixedforms. In addition, the material for forms and thelabor for setting forms are eliminated. As a result,the cost for large jobs will be less for slipform place-ment than for placement with fixed forms. However,on small jobs or larger jobs with special requirements,the use of fixed forms may be necessary or may bemore economical than the use of slipform equipment.No guidelines can be given as to what size job willpermit the economic use of slipform pavers.

b. Placing time. Concrete will be placed beforeobtaining its initial set and within 45 minutes aftercement has been added to the batch. These provisions

apply to all paving projects regardless of the type ofmixing equipment used. The addition of water to themixture in excess of that required by the mixtureproportions to maintain slump during prolongedmixing will not be permitted.

c. Slipform paving. Approval of the slipform pavingequipment for airfield pavement will be based on satis-factory performance in the field. Trial sections ofsufficient length and located in low-volume aircrafttraffic areas will be used to approve the paving equip-ment, considering both slipform and another for thefill-in operation when scheduled by the contractor.Furthermore, approval shall be based on the abilityof the machine to consolidate the concrete and formthe pavement to the desired cross sections. Plangrade and surface smoothness tolerances must bemet. Particular attention should be paid to the abilityof the machine to form the required edge withoutexcessive slumping or tearing during slipform opera-tions and to form a suitable longitudinal constructionjoint during fill-in operations. The machine shall notdamage the surface or edge of the previously placedslab during fill-in operations. The suggested lengthof the trial section is 1,000 to 2,000 feet. Slipformpavers with a full-width auger are recommended.Traveling blades have been less satisfactory. If theslipformed pavement is 10 inches or greater inthickness, some of the lighter slipform pavers mayhave problems properly handling the low-slumpconcrete.

d. Spreading. Hand spreading of concrete will bepermitted only when necessitated by odd widths orshapes of slabs, or in emergencies such as equipmentbreakdown.

e. Vibration. Vibration requirements are influencedby many factors, such as the type and size of aggre-gate, mixture proportions, air entrainment, slump,workability of mixture, and pavement thickness.The specified maximum spacing for vibrator unitsand the specified vibrating procedures are based onfield experience with the vibration of pavements 12inches or more in thickness. There has been onlylimited use of internal vibration for thinner slabs. Ifnecessary for proper consolidation of the concrete, acloser spacing of vibrator units will be required.Particular attention should be paid to vibratorsalong the edge of the paving lane to ensure that theedge is properly consolidated. General experiencehas been that it is more satisfactory to use vibratorsat a closer spacing and for shorter periods of vibra-tion than to attempt to consolidate the concrete byprolonged vibration at a wider spacing. The duration

TM 5-822-7/AFM 88-6, Chap. 8

of the vibration will be limited by the time necessaryto produce a satisfactory consolidation of theconcrete, and over-vibration will not be permitted.Vibrators must not be permitted to touch forms,dowels, tie bars, or other embedded items.

f. Surface vibrators. Surface vibrators will not bepermitted because past experience with them hasbeen generally unsatisfactory. Surface vibrationtends to bring excess fine material and water to thesurface, which in many instances contributes tosurface deterioration and scaling. Surface-vibratorpans also tend to ride on high places in the concretesurface and thus cause non-uniform consolidation ofthe concrete.

g. Steel reinforcement. Project drawings will showtypical details of all slab reinforcement and willindicate the pavements requiring reinforcement andthe location and amount of steel required in theslabs. This information will supplement the specifi-cation requirements for reinforcement, and allrequirements will be carefully checked to insure nodiscrepancies between drawings and specificationrequirements.

h. Placing during cold weather. Pavement concreteshould not be placed when the air temperature isbelow 40 degrees F. If unusual job conditions requireconstruction at these low temperatures, specialprovisions for placement and protection of theconcrete will be needed. For additional informationon winter concreting, refer to ACI 306R. Thenecessary covers and other means of protecting theconcrete during cold weather should be available onthe job before starting concrete placement. Calciumchloride as an admixture may be either required orapproved to accelerate the setting time of concreteplaced during cold weather. No changes will be madein the requirements for temperature of the concretewhen placing or for protection of the concrete

against freezing when calcium chloride or any other accelerator is used.

i. Placing during hot weather. During hot weatherspecial precautions are necessary to prevent theformation of plastic-shrinkage cracks which resultfrom an excessive loss of moisture from the concretebefore curing is begun. The concrete needs to be placedat the coolest temperature practicable, and in no caseshould the temperature of the concrete as placedexceed 90 degrees F. Mixing and placing of concretewill be controlled to keep moisture loss at aminimum. Aggregates will be moist when added tothe mixer, and the subgrade dampened so it will notabsorb water from the concrete. The temperature ofthe concrete may be reduced by using cement with alower temperature by sprinkling the stockpiles ofaggregate to produce cooling by evaporation, by pre-cooking mixing water and by avoiding delays in mixingand placing concrete. The concrete needs to be placedand finished as rapidly as practicable, and the curingstarted without delay. If the application of the curingmedium should for any reason lag placement for atime sufficient to permit surface drying, the surfaceshould be kept damp with a fog spray, and placementshould be discontinued until corrective action can betaken. The fog spray equipment will be capable of applying a very fine mist to the concrete to replacemoisture lost by evaporation. In windy areas,screens may be needed to protect the concrete fromrapid evaporation caused by wind. Steps shall betaken to avoid an evaporation rate in excess of 0.2pound per square foot per hour as shown in figure 1.This is adequate for most conditions, but there arereports of plastic-shrinkage cracking occurringunder adverse conditions when the indicated evapor-ation rate was as low as 0.15 pound per square footper hour. Additional information is available in ACI305R.

18

TM 5-822-7/AFM 88-6, Chap. 8

Figure 1. Prediction of concrete rate of evaporation

(From Curing of Concrete, Concrete Information Sheet,

5.0

4.0

3.0aI

%3

2.0 y

1.0

0

1966, with permission of the Portland Cement Association,Skokie, IL. )

19

TM 5-822-7/AFM 88-6, Chap. 8

j. Placing of small areas. For vehicular parking andpaving projects of 1,600 cubic yards or less, machinespreading, finishing, and floating will not be requiredif the benefits derived from the use of the equipmentare not commensurate with the cost of using themachines. In this case, hand spreading, finishing,and floating will be specified.

k. Overlay pavement construction.(l.) General. Where overlay pavement construction

is required, contract specifications will containspecial provisions for preparation and treatment ofthe existing surface before placing concrete in theoverlay pavement. Criteria herein pertain toconstruction of rigid overlays on existing rigidpavement. Construction of rigid overlays on existingflexible pavement or on existing rigid pavement witha bond breaking course is treated as new construction.Construction of thin bonded overlays is discussed inappendix B.

(2.) Bond between layers of pavement. Overlaypavements generally are designed on the assumptionthat a partial bond will develop between the twoconcrete layers. Concrete surfaces to receive partiallybonded overlays will be thoroughly cleaned of dirtand other foreign material, loose or spalled concrete,extruding joint seal, bituminous patches, andmaterial that would break the bond between theconcrete layers. Different areas of pavement willrequire different treatment. The condition of theexisting pavement will determine the cleanupmeasures necessary. Normally, sandblasting orsurface-abrading equipment will be required toremove material adhering to the surface, and handscaling of loose or spalled material will be required.No special treatment such as an acid wash of theprepared surface or the use of a grout bonding coursewill be required for partially bonded overlays. Inareas where oil or grease is present on the surface,scrubbing with a detergent and a wire brush may berequired. Cleaning of surfaces to receive the overlaywith rotary grinding equipment will be permitted,but the surface must be swept clean prior to placingthe concrete overlay.

(3.) Control of cracking in overlay pavements.Considerable difficulty has been experienced withuncontrolled cracking of overlay pavements atcontraction joints. This cracking is likely to occurduring hot weather when the temperature of theexisting pavement is appreciably higher than that ofthe concrete being placed in the overlay. Contractiondue to cooling of the base pavement results in move-ment at the existing joint, which may start a crack in

20

the bottom of the overlay as the concrete hardens.This cracking may occur when the concrete is toogreen to saw. Often the crack is not visible at thesurface of the pavement when the sawing is done. Toprevent such cracking, it may be necessary to useinserts in the plastic concrete to form contractionjoints.

1. Control of cracking in pavements placed on leanconcrete and cement-stabilized bases. Occasionalproblems have developed when relatively thinconcrete pavement has been placed directly on leanconcrete bases or stabilized bases with high cementcontents. Uncontrolled contraction cracks in thebase material have on occasion reflected through thenew pavement. If a thin pavement less than 9 inchesthick is to be placed directly on a cement-stabilizedor lean concrete base, it may be desirable to eitherplace a bond-breaking material between the pave-ment and base or to saw cut contraction joints in thebase to match those in the pavement surface. If abond breaker is used between the pavement surfaceand the base, the design engineer must be aware ofthe lack of bond since this can affect the requireddesign thickness of pavement. If contraction jointsare to be sawed in the base to control cracking, itmust be done at an early age just as discussed inparagraph 22d for concrete pavements.

m. Appendix D describes the methods and pro-cedures for the construction of roller compactedconcrete pavements.

17. Field test specimens.a. General. Field tests other than those called for

by contractor quality control will be conducted bythe Government to determine the slump and aircontent of freshly mixed concrete, and specimenswill be molded to test for flexural strength of hardenedconcrete. All tests will be performed under the super-vision of the contracting officer. However, since thecontractor will be required to furnish concretesamples, labor, and facilities for molding and curingtest specimens, specifications must indicate theextent of testing required. Equipment for makingair-content and slump tests will be furnished by thecontracting officer when the Government is respon-sible for testing and by the contractor when thecontractor is responsible for testing. Beam moldswill be made of steel and will be rigid and watertight.Beam molds will be supplied by the contractingofficer except when the contractor is responsible fortesting. When molds are required to be furnished bythe contractor, details necessary to assure that the

TM 5-822-7/AFM 88-6, Chap. 8

molds furnished are satisfactory will bein the contract specifications.

b. Specimens for strength tests. Test

inc luded

specimensfor determining conformance with specified strengthrequirements will be moist-cured under fieldlaboratory conditions. The size and number of curingtanks will depend on the number of specimens takenand the ages at which the tests are made. For airfieldpaving projects, flexural-strength tests will beconducted at the ages of 7, 14, and 90 days. For otherpavements, designed on the basis of 28-day flexuralstrengths, the test ages will be 7, 14, and 28 days.Where 90-day flexural strength tests are required,provision will be made for curing and testing ofspecimens after the project is completed.

c. Specimens for determining time of openingpavement to construction traffic. Ordinarily, nofield-cured specimens will be required. However, forcold-weather construction when field-strength datamay be necessary to permit the opening of the pave-ment or portions thereof to construction traffic priorto 14 days, test groups of at least three beams shallbe taken, as required, from concrete placed indesignated areas. The beams of each test group shallbe made from a single batch of concrete and shall becured in accordance with ASTM C 31.

18. Finishing.a. Equipment and methods. Types of finishing

equipment other than conventional equipment maybe used on a trial basis when capable of finishingconcrete of the quality and consistency required.Equipment that fails under trial to perform in asatisfactory manner will be rejected and removedfrom the work area.

b. Surface finishing and testing. Finishing opera-tions are designed to obtain a dense, smooth surfacetrue to the required grade. Since the surface receivesthe greatest exposure to weathering and traffic,every precaution will be taken to obtain a high-qualityconcrete at the surface. The finishing operations willbe kept to the minimum necessary to obtain therequired surface finish. Excessive surface manipula-tion will not be permitted because it tends to bring asurplus of mortar, water, and undesirable softmaterials to the surface which contributes to scalingand surface deterioration. Finishing should leave thesurface at the proper grade. If the mechanicalfinishing operations are properly controlled, very littlehand finishing will be necessary. Short floats will beused only as necessary to correct local surfaceuneveness. Straightedges of the required length will

be used primarily to smooth and check the surface.To avoid later costly corrections of hardened pave-ment which fails to conform with specified surfacetolerances, the surface will be thoroughly checkedduring the mechanical floating, and necessarycorrections will be made.

c. Hand finishing and edging. Machine finishing isrequired, and hand finishing is only permitted forodd widths and shapes of slabs, areas adjacent toheaders, and areas around outlets in the pavements.Hand-finished areas will have the same quality andthe same surface characteristics as those areas finishedby machine. Hand finishing along the edges of slip-formed lanes to correct edge slumping or to repairareas damaged by tearing or sloughing shall be heldto a minimum. The only manipulation permittedalong the edges of slipformed lanes shall not disturbthe edge or use the edging tools to correct deficienciesin the edge.

d. Surface texture. The final surface texture of thepavement will be provided by means of a burlapdrag, broom, artificial turf, wire comb, or grooving.Dragging the surface of the concrete in the directionof concrete placement with moist burlap leaves a finesandy surface that is adequate for low-speed traffic.At least 2 feet of burlap must be in contact with theconcrete, and the burlap should be cleaned asnecessary. An improved skid-resistant surface canbe produced with a broom consisting of multiplerows of stiff bristles capable of producing serrations1/16 to1/8 of an inch deep. The brooms will have to becleaned frequently during texturing. Artificial turfhas been used successfully for texturing concrete.This is applied in the same manner as the burlap withat least 2 feet of the artificial turf in contact with theconcrete. One artificial turf that has provided asatisfactory texture consisted of 7,200 polyethyleneturf blades approximately 0.85 inch long per squarefoot. The wire comb provides the most skid-resistanttexture of the finishing techniques described so far.However, it is also the most difficult to use andadjustments to the concrete proportions may have tobe made to find a mixture that can be wire-combedwithout objectionable surface tearing. The wirecomb should consist of flexible spring steel linesspaced not less than 1/2 inch nor more than 1 inchapart. Closer spacing causes problems with raveling,and wider spacing results in objectionable roadnoise. The serrations left by the steel lines should beabout 1/8 to 1/4 inch deep and 1/16 to 1/8 inch wide. A singlepass of burlap or artificial turf can be made beforethe wire comb if desired. Because of problems with

21

TM 5-822-7/AFM 88-6, Chap. 8

skid resistance for aircraft traveling at high speed,the Air Force requires that new runways have aburlap drag finish with saw-cut grooves. Figure 2shows the grooving requirements for an Air Forcerunway. If the constructed pavement surface texture

Figure 2. Air Force runway

is inadequate due to poor texturing techniques, rain-fall on insufficiently hardened concrete, or othercauses, grooving or grinding will restore the skidresistance of the surface.

grooving requirements.

22

TM 5-822-7/AFM 88-6, Chap. 8

19. Curing.a. Control of cracking. Plastic shrinkage (craze)

cracking is caused by a combination of (1) highambient air temperature, (2) high concretetemperature, (3) low relative humidity, and (4) windvelocity. These conditions need to be controlledwhen placing and protecting young concrete. It isessential that concrete be protected against the 10SSof moisture and rapid temperature change for thespecified period of protection. All equipment,material, and supplies for adequate curing andprotection of the concrete must be on hand and readyto install before actual concrete placement begins. Ingeneral, curing will be accomplished by using apigmented membrane-curing compound. However,other methods may be specified if indicated by localconditions.

b. Membrane curing. The curing compound will beapplied by means of a power-driven machinestraddling the newly paved lane and operated so thatthe spray will cover the pavement surface completelyand uniformly. Spray nozzles must be surrounded bya hood to prevent wind from blowing the curingcompound spray. The rate of advance and spacing ofnozzles of the spraying machine will be controlled sothat a two-coat overlapping coverage will be provided.Hand-operated pressure sprayers will be permittedonly on indicated odd widths and shapes of slabs andon concrete surfaces exposed by removal of forms.The curing compound must form a continuous void-

free membrane and be maintained in this conditionthroughout the curing period. Unsatisfactory ordamaged areas will be resprayed. Any damage to themembrane during the sawing operation will becorrected by respraying. When forms are removed,the exposed faces of the concrete will be sprayedwith curing compound.

c. Substituting curing provisions. Where it hasbeen established from past experience in an area thatmembrane curing alone does not adequately protectpavement from shrinkage cracking, a combination ofmoist curing and membrane curing may be specified.

d. Selection of curing material for pavements to bepainted. In selecting curing material for pavementsurfaces to be painted, consideration will be given tothe necessity of sandblasting to remove coatings anddeposits that interfere with the bonding of paint.Curing compounds of the low-melting-point wax-base type tend to penetrate concrete and should notbe used in the areas to be painted.

20. Grade and surface-smoothness requirements.a. Heliport and airfield pavements. The specified

grade and smoothness requirements applicable toairfield and heliport pavements are shown in table 8.The finished surfaces of airfield and heliportpavements shall have no abrupt change of 1/8 inch ormore and shall not deviate from the testing edge ofan approved 12-foot straightedge more than thetolerances shown in table 8.

Table 8. Surface smoothness - airfield and heliport pavements

Direction TolerancesItem No. Pavement Category of Testing inches

1 Runways and taxiways

2

3

Calibration hardstands and compassswinging bases

Other airfield and heliport areas

b. Road, street, and open-storage concretepavements. Pavements shall be smooth and true tograde and cross section. When tested with a 10-footstraightedge on lines 5 feet apart parallel with thecenterline of the pavement, the surface shall not varymore than 1/8 inch from the testing edge of thestraightedge.

Longitudinal 1/8Transverse 1/4

Longitudinal 1/8Transverse 1/8

Longitudinal 1/4Transverse 1/4

c. Requirements for other vehicular pavements.Parking area, motor-pool and motor-storage area,repair- yard, and open-storage area pavements shallbe smooth and true to grade and cross section. Whentested with a 10-foot straightedge on lines 5 feetapart parallel with and at right angles to the center-line of the paved area, the surface shall vary not more

23

TM 5-822-7/AFM 88-6, Chap. 8

than 1/4 inch from the testing edge of the straightedge.d. Slipform paving edge slump. Edge slump is the

downward movement of the plastic concrete thatoccurs when the sliding form passes. Excessiveslump is indicative of improper concrete mixtureproportioning. If the concrete mixture cannot bere