Parvalux Electro Magnetic (Fail Safe) Stop · PDF fileCharacteristics of Permanent Magnet...
Transcript of Parvalux Electro Magnetic (Fail Safe) Stop · PDF fileCharacteristics of Permanent Magnet...
Parvalux Electro Magnetic (Fail Safe) Stop Brakes
(P1 – P6) and PM50/60 Permanent Magnet Motors
Motor and Brake Wiring Diagram
Connection Diagrams for
Permanent Magnet Motors
For frequent stop/starts (more than 3 per minute) pleasecontact our sales engineers.
24 volts DC (fail safe) single disc brake for PM 7, 8, and 9.This Electro-Magnetic Disc Brake is a spring appliedelectrically released unit which provides Fail-to-Safeoperating characteristics, such that on interruption, orfailure of power supply, the brake will engage and arrestthe load. Size:
Diameter 50mmOverall Height 56.5mmLead Length 200mmWeight 0.160KgIncrease in LengthWhen fitted to motor +35mm
Motors fitted with 3 core Cable Motors fitted with 2 leads
Yellow and Green EARTH
MOTOR ROTATION ANTI-CLOCKWISE LOOKING ON DRIVE END
Brown
Blue
ARMATURE D.C. SUPPLY
W.D. 75 (cable)
D.C. SUPPLY
Reverse Rotation
MOTOR ROTATION ANTI-CLOCKWISE LOOKING ON DRIVE END
Black
Red
ARMATURE D.C. SUPPLY D.C. SUPPLY
Reverse Rotation
DIMENSIONSTYPE P1 P3 P5 DIMENSIONS APPROVALS TYPE P2 P4 P6
BrakeSize
P1-P3-P5
Weight
575g
BrakeSize
P2-P4-P6
Recommended Motor Frames
PM 1, PM 3, PM 10 and PM 11
Recommended Motor Frames
PM 2, PM 4, PM 5, PM 6,PM 50 and PM 60
InputPower
InputVolts
RatedTorque
110vA.C.
0.4Nm
230vA.C.
0.4Nm
24vD.C.
0.4Nm
ENCLOSURE
IP 55
InputVolts
RatedTorque
110vA.C.
1Nm
230vA.C.
1Nm
24vD.C.
1Nm
24VA
(14w)
24VA
(14w)
24VA
(14w)A B C
38 65 12All dimensions in (mm)
A: inc adaptor plate
CSA C-USC.E. Rec.“Class F”
InputPower
24VA
(14w)
24VA
(14w)
24VA
(14w)A B C
38 65 12All dimensions in (mm)
A: inc adaptor plate
Double PoleSwitch
BRAKE
BRAKE
Armature
Armature
D.C. SUPPLY SEPARATE A.C. SUPPLY
Dou
ble
Pol
e S
witc
h
D.C
. SU
PP
LY
69 71
These single-disc electro magnetic brakes are spring applied electrically released units which provide fail to safe operating characteristics, such that on interruption, or failure
of power supply, the brake will engage and arrest the load. These brakes operate from single phase a.c. supply (not P5 or P6) and incorporate a built in rectifier. This offers
the brake a vibration free characteristic through a lower operating voltage spectrum.
A
BC
2 core cable 40cm long minimum
W.D.77 (Leads)
72
EMC Filter
EMC FILTER41mm dia. x 75mm long with 8mm fixingstud and nut. 12mm long. Lead length30cm. For use with commutator andpermanent magnet motor, to reduce theemissions the motor might make whichcould affect adjacent sensitiveequipment. The filter is connectedbetween the supply and the motor.
(unless declined in writing bycustomer, will be supplied)
Characteristics of Permanent Magnet Motors
Typical Performance Curves= Maximum continuous rating
5000
4000
3000
2000
1000
0 10 20 30TORQUE (Ncm)
9
8
7
6
5
4
3
2
1
CU
RR
ENT
(am
ps)
TORQUE/CURRENTTORQUE/SPEED
SPE
ED (r
pm)
PM8 4000r.p.m. – 12v d.c. – 33 watts
5000
4000
3000
2000
1000
0 10 20 30 40 50 60TORQUE (Ncm)
2.0
1.5
1.0
0.5
CU
RR
ENT
(am
ps)
TORQUE/CURRENT
TORQUE/SPEED
SPE
ED (r
pm)
PM11 3000r.p.m. – 180v d.c. – 65 watts
5000
4000
3000
2000
1000
0 10 20 30 40 50 60TORQUE (Ncm)
5
4
3
2
1
CU
RR
ENT
(am
ps)
TORQUE/CURRENT
TORQUE/SPEED
SPE
ED (r
pm)
PM1 3000r.p.m. – 50v d.c. – 90 watts
5000
4000
3000
2000
1000
0 20 40 60 80 100 120TORQUE (Ncm)
5
4
3
2
1
CU
RR
ENT
(am
ps)
TORQUE/CURRENT
TORQUE/SPEED
SPE
ED (r
pm)
PM6 3000r.p.m. – 110v d.c. – 150 watts
5000
4000
3000
2000
1000
0 14 70 113 TORQUE (Ncm)
20
CURR
ENT
(am
ps)
TORQUE/CURRENT
TORQUE SPEED
SPEE
D (r
pm)
28 42 56 84 98
5
10
15
25
PM60 4000 r.p.m. – 24v d.c. – 280 watts
3500
3000
2500
2000
1500
0 14 70 113 TORQUE (Ncm)
16
14
10
6
2
CURR
ENT
(am
ps)
TORQUE/CURRENT
TORQUE SPEED
SPEE
D (r
pm)
28 42 56 84 98
4
8
12
PM50 3000 r.p.m. – 24v d.c. – 155 watts
5000
4000
3000
2000
1000
0 10 20 30 40 50 60TORQUE (Ncm)
10
8
6
4
2
CU
RR
ENT
(am
ps)
TORQUE/CURRENT TORQUE/SPEED
SPE
ED (r
pm)
PM10 4000r.p.m. – 24v d.c. – 60 watts
5000
4000
3000
2000
1000
0 10 20 30 40 50 60TORQUE (Ncm)
2.0
1.5
1.0
0.5
CU
RR
ENT
(am
ps)
TORQUE/CURRENT
TORQUE/SPEED
SPE
ED (r
pm)
PM11 4000r.p.m. – 180v d.c. – 90 watts
5000
4000
3000
2000
1000
0 10 20 30 40 50 60TORQUE (Ncm)
5
4
3
2
1
CU
RR
ENT
(am
ps)
TORQUE/CURRENT
TORQUE/SPEED
SPE
ED (r
pm)
PM1 4000r.p.m. – 50v d.c. – 120 watts
5000
4000
3000
2000
1000
0 20 40 60 80 100 120TORQUE (Ncm)
3
2
1
CU
RR
ENT
(am
ps)
TORQUE/CURRENT
TORQUE/SPEED
SPE
ED (r
pm)
PM6 4000r.p.m. – 110v d.c. – 200 watts
73
Per
man
ent
Mag
net
15 MIN 15 MIN
OUTPUT (watts)
Permanent Magnet Type MotorsVariable Speed – D.C.
Enclosures: – PM 1–PM 2–PM 6 – PM 60– Drip Proof Internal Fan Cooled (IP 21)PM 3–PM 4–PM 5 – PM 50 – PM 7 to PM 11 – Totally Enclosed (IP 54)
Motor Types:
PM 7 to PM11PM 1–2–6 PM 60PM 3–4–5 PM 50
PM 10 PM 2 + T/Box PM 60
� Voltage Range: 12v, 24v, 50v, 110v or 200v, D.C. Other voltages quotedfor on request.
� Starting Current: Approximately 3 times full load.
� Rotation: Reversible two leads as standard.
� Construction: Motors – Shielded ball bearings spring loaded for quietrunning.Single Reduction Gearboxes: Fitted with ball bearings, alloy gearboxwith composite gear, grease lubricated for life and suitable for mounting inany position.In-Line Double Reduction Gearboxes: Fitted with ball bearings, alloygearbox with composite gear, grease or oil bath lubricated for life andsuitable for mounting in any position.Spur Reduction Gearboxes: Fitted with ball bearings, alloy gearboxwith composite pinion gear and multi-spur type hardened steel gears, oilbath lubricated for life and suitable for mounting in any position.
� Connections: 30cm P.V.C. flexible (Terminal box on request). Notapplicable to PM7/8/9 PM10/PM11.
� Insulation: Class ‘F’ (maximum temperature rise 115°C at a maximumambient of 40°C).
� Specifications: B.S. 5000 part 11. (I.E.C. 72). (CSA c-us if specified).
� Optional Extras: Double ended motor spindles.Double ended gear shafts (not available on in-line gearboxes).Non standard shafts (stainless steel, keyways, flats, etc).Terminal box (one position only, on top). PM1 – 6 / PM50/60Holes tapped for spigot mounting.3 core cable on request (class ‘B’).
� Electro-Magnetic Brake: Page 72.
� Thyristor D.C. Controller: Contact Parvalux, for supplier details.
� Tachogenerator: Page 117.
� Additional Extras for Geared Units: (Non standard cataloguereductions available on request).
� Bronze Gears: (Single and double reduction final gears).
� Flange Mounting Gearbox Details: Page 114.
� Gearbox Shaft Positions: Page 113.
PM 8
15 MINCONT 15 MIN 1 HOUR 1 HOUR 1 HOUR1 HOUR CONT CONT CONT
FullLoadr.p.m.
PM 3 PM 4 PM 5 PM 50Totally Enclosed (IP 54)
1500
2000
3000
4000
5000
30
45
68
90
112
40
60
90
120
150
60
90
120
150
200
40
60
90
120
150
50
80
120
160
200
75
120
160
200
260
50
80
120
160
200
60
100
150
200
250
80
150
200
250
300
65
105
155
205
255
85
135
200
265
330
120
185
280
375
465
OUTPUT (watts)
CONT CONT CONT CONT CONT15 MIN 15 MIN 15 MIN 15 MIN 15 MIN1 HOUR 1 HOUR 1 HOUR 1 HOUR 1 HOUR
FullLoadr.p.m.
PM 7 PM 8 PM 9 PM 10 PM 11Totally Enclosed (IP 54)
1500
2000
3000
4000
5000
7.5
10
15
20
25
10
13
20
25
30
13
17
25
33
40
12.5
17
25
33
40
15
21
33
40
48
18
24
38
48
55
19
25
38
50
62
24
33
45
60
70
26
36
55
70
80
20
30
45
60
75
25
40
55
75
90
35
50
70
100
120
33
45
65
90
110
40
55
80
110
130
45
65
100
130
160
30 MIN 1 HOUR 15 MIN
OUTPUT (watts)
CONT CONT CONT CONT30 MIN 30 MIN
FullLoadr.p.m.
PM 1 PM 2 PM 6 PM 60*Ventilated (IP 21)
1500
2000
3000
4000
5000
40
60
90
120
150
60
90
120
150
200
50
80
120
160
200
75
120
160
200
260
60
100
150
200
250
80
150
200
250
300
85
140
210
280
350
110
170
255
340
425
155
230
345
460
575
NOTE: These outputs are based on a pure D.C. supply (i.e. form factor 1) with electronic control, outputs will be reduced, to what degree depends on the formfactor (FF) and the matching of motor and controller.We recommend a controller range to give the best performance and brush life.
74
*PM 60: For 160 V DC and above on the PM 60 the output power is reduced to the PM 50 figures (see below)
Ø 35
PM 10 = 111PM 11 = 130
Ø 51
7.92
0Ø
Ø 66
7.92
7
4.3
38
35.5
9.7
34
PM 10 = 66PM 11 = 85
10
45
35
251010.7
PM 10PM 11
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 10
Spigot ‘M’ can be machined to 34.54/34.49mm dia. concentric with shaft 0.05mm T.I.R.Optional shaft at lead end 7.93mm dia.�33mm long.
Approx. weight: PM 10 – 1.12 KgPM 11 – 1.58 Kg
PM 3 = 141PM 1/4 = 153PM 2/5 = 166PM 6 = 179 Ø 35
7.92
0Ø Ø
12
Ø 77
7.92
7
4.3
68
40.6
40.6
15°
71
28.4
PM 3 = 69.5PM 1/4 = 82PM 2/5 = 95PM 6 = 107.6
11
51
40
29
40
1111
PM 1 – PM 2 – PM 6PM 3 – PM 4 – PM 5
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 1/4
Spigot ‘M’ can be machined to 34.54/34.49mm dia. concentric with shaft 0.05mm T.I.R.Optional shaft at lead end 10mm dia.�33mm long.
Approx. weight: PM 1/3 – 2.11 KgPM 2/4 – 2.46 KgPM 5/6 – 2.65 Kg
Leads out here 30cm
.‘M’ spigot,see note.
‘M’ spigot,see note.
4 holes on 67.6mm P.C.D.Can be tapped M5�10mm deep.
4 holes on 67.6mm P.C.D.Can be tapped M5�8mm deep.
8 holes equally spacedon 41.3mm P.C.D. canbe tapped M5�6mmdeep.
Optional terminal box tapped 20mmconduit or PG 13.5 on request.Standard entry position R.H.S.
4 holes on 41.3mm P.C.D.Can be tapped M5�10mm deep.
3 mounting feet tappedM5�10mm deep.
75
42.5
PM 7 = 88
Ø 35
PM 8 = 101PM 9 = 114 Ø 51
7.92
0Ø
Ø 56
7.92
7
4.3
38
PM 7 = 47
9
8.8
30
PM 8 = 60PM 9 = 73
10
45
35
259
PM 7PM 8PM 9
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 8
Spigot ‘M’ can be machined to 34.54/34.49mm dia. concentric with shaft 0.05mm T.I.R.Optional shaft at lead end 7.93mm dia.�33mm long.
Approx. weight: PM 7 – 0.5 KgPM 8 – 0.7 KgPM 9 – 0.9 Kg
Leads out here 30cm(flexible grommet). ‘M’ spigot,
see note.
4 holes on 41.3mm P.C.D.Can be tapped M5�10mm deep.
3 mounting feet tappedM4�10mm deep.
Leads out here 30cm
PM 50 = 184PM 60 = 197
Ø 35
7.92
0Ø Ø
12
Ø 77
7.92
7
4.3
68
40.6
40.6
15˚
71
28.4PM 50 = 112.7PM 60 = 125.4
11
51
40
29
40
1111
PM 50PM 60
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 50
Spigot ‘M’ can be machined to 34.54/34.49mm dia. concentric with shaft 0.05mm T.I.R.Optional shaft at lead end, 10mm dia.�33mm long. Approx. weight:: PM 50/60 – 2.90 Kg
‘M’ spigot,see note.4 holes on 67.6mm P.C.D.
Can be tapped M5�8mm deep.
8 holes equally spaced on41.3mm P.C.D. can betapped M5�6mm deep.
Leads out here 30cm
Optional terminal box tapped 20mmconduit or PG 13.5 on request.Standard entry position R.H.S.
Per
man
ent
Mag
net
On request, 3 mounting feetcan be drilled and tapped M5.
On request, 3 mounting feetcan be drilled and tapped M5.
COMPOSITE
OUTPUT TORQUE (Nm)FINALR.P.M.
FINALR.P.M.
FINALR.P.M.
FINALR.P.M.
GEARBOXRATIO
OUTPUT TORQUE (Nm) OUTPUT TORQUE (Nm) OUTPUT TORQUE (Nm)
COMPOSITE COMPOSITE COMPOSITE
Single Reduction Worm Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosures: Totally Enclosed (IP 54)
Gearbox Type:
SSpeed Range: 22 – 970 r.p.m.
Cont 1 Hour Cont 1 Hour Cont 1 Hour
7.5 10 12.5 15 19 24watts watts watts watts watts watts
Motor Rating @ 1500 r.p.m.
Cont 1 Hour Cont 1 Hour Cont 1 Hour
10 13 17 21 25 33watts watts watts watts watts watts
Motor Rating @ 2000 r.p.m.
Cont 1 Hour Cont 1 Hour Cont 1 Hour
15 20 25 33 38 45watts watts watts watts watts watts
Motor Rating @ 3000 r.p.m.
Cont 1 Hour Cont 1 Hour Cont 1 Hour
20 25 33 40 50 60watts watts watts watts watts watts
Motor Rating @ 4000 r.p.m.
PM 7 S PM 7 S PM 7 S PM 7 SPM 8 S PM 8 S PM 8 S PM 8 SPM 9 S PM 9 S PM 9 S PM 9 S
76
PM 8 S
70:166:160:154:148:144:140:136:133:130:127:125:1
22 1/2:120 1/2:118 1/2:116 1/2:115 1/2:114 1/2:113 1/3:112 1/2:111 1/3:110 1/3:19 1/3:18 1/3:17 1/4:16 1/6:15 1/8:14 1/8:1
2223252831343842455056606773819197103113120132145161180207243293364
1.21.11.11
0.90.90.80.80.70.70.60.60.60.50.50.50.40.40.40.40.40.30.30.30.30.20.20.2
1.21.11.11
0.90.90.80.80.70.70.60.60.60.50.50.50.40.40.40.40.40.30.30.30.30.20.20.2
1.21.11.11
0.90.90.80.80.70.70.60.60.60.50.50.50.40.40.40.40.40.30.30.30.30.20.20.2
1.21.11.11
0.90.90.80.80.70.70.60.60.60.50.50.50.40.40.40.40.40.30.30.30.30.20.20.2
1.51.51.41.31.31.21.111
0.90.90.80.80.70.70.60.60.60.50.50.50.40.40.40.30.30.30.2
1.51.51.41.31.21.21.111
0.90.80.80.70.70.60.60.60.60.50.50.50.40.40.40.30.30.30.2
1.51.51.41.31.31.21.111
0.90.90.80.80.70.70.60.60.60.50.50.50.40.40.40.30.30.30.2
1.51.51.41.31.31.21.111
0.90.90.80.80.70.70.60.60.60.50.50.50.40.40.40.30.30.30.2
1.51.51.81.71.61.51.41.31.21.11.11
0.90.90.80.80.70.70.70.60.60.60.50.50.40.40.30.3
1.51.51.81.71.61.51.41.31.31.21.111
0.90.80.80.80.70.70.70.60.60.50.50.40.40.30.3
1.51.51.81.71.61.51.41.31.21.11.11
0.90.90.80.80.70.70.70.60.60.60.50.50.40.40.30.3
1.51.51.81.71.61.51.41.31.21.11.11
0.90.90.80.80.70.70.70.60.60.60.50.50.40.40.30.3
2830333742455056616774808998108121129138150160176194214240276324390485
434550566368758391100111120133146162182194207225240265290321360414487585727
576167748391100111121133148160178195216242258276300320353387429480552649780970
––
2.12
1.91.81.71.61.51.41.31.21.11.11
0.90.90.90.80.80.70.70.60.60.50.50.40.3
––
2.32.12
1.91.71.61.61.41.41.31.21.111
0.90.90.80.80.80.70.70.60.50.50.40.3
––
2.32.22.12
1.81.71.61.51.41.41.21.21.111
0.90.90.90.80.70.70.60.60.50.40.4
––
2.32.22.12
1.81.71.61.51.41.41.21.21.111
0.90.90.90.80.70.70.60.60.50.40.4
––
2.32.32.32.32.12
1.91.71.61.61.41.41.31.21.11.111
0.90.80.80.70.70.60.50.4
––
2.32.32.32.22.12
1.81.71.61.51.41.31.21.11.11.111
0.90.80.80.70.60.60.50.4
––
2.32.32.32.32.12
1.91.71.61.61.41.41.31.21.11.111
0.90.80.80.70.70.60.50.4
––
2.32.32.32.22.12
1.81.71.61.51.41.31.21.11.11.111
0.90.80.80.70.60.60.50.4
––––––
2.72.52.42.22.12
1.81.71.61.51.41.41.31.21.21.11
0.90.80.70.60.5
––––––
2.72.62.42.32.12
1.91.81.61.51.51.41.31.31.21.111
0.90.80.60.5
–––––
2.32.52.32.22.11.91.81.71.61.51.41.31.31.21.21.11
0.90.90.80.70.60.5
–––––
2.32.52.32.22.11.91.81.71.61.51.41.31.31.21.21.11
0.90.90.80.70.60.5
42.5
30
PM 9 S = 168PM 8 S = 156PM 7 S = 143
83.8
4429
55.4
Ø 56
27.5
1025
35
45
9
PM 7 = 47
9
PM 9 = 73PM 8 = 60
37
PM 7 SPM 8 SPM 9 S
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 8 S
Optional shaft at motor speed (lead end only) 7.93mm dia.�33mm.
Approx. weight: PM 7 S – 0.9 KgPM 8 S – 1.1 KgPM 9 S – 1.3 Kg
9mm dia. h6.Flat 6mm�19mm long.
3 mounting feet tappedM4�10mm deep.
Leads out here 30cm(flexible grommet).
� Voltage, Construction, Connections, Motor PerformanceSpecifications and Optional Extras see pages 72 and 74 for full details.
(1 Nm = 8.85 lbs. ins.) (1 Nm = 10.2 cmkp)
PM 10 S = 166
87.7
4429
34
59.4
Ø 66
35.5
27.5
PM 11 S = 185
PM 10 = 66PM 11 = 85
10
45
35
251010.7
37
––––––––––––
2.92.62.42.32.22.12
1.71.71.61.51.41.31
0.80.6
––––––––
2.92.82.52.52.42.12
1.91.81.71.61.41.41.31.21.11
0.80.60.5
COMPOSITE
OUTPUT TORQUE (Nm)FINALR.P.M.
FINALR.P.M.
FINALR.P.M.
FINALR.P.M.
GEARBOXRATIO
OUTPUT TORQUE (Nm) OUTPUT TORQUE (Nm) OUTPUT TORQUE (Nm)
COMPOSITE COMPOSITE COMPOSITE
Cont 1 Hour Cont 1 Hour
20 25 33 40watts watts watts wattsMotor Rating @ 1500 r.p.m.
Cont 1 Hour Cont 1 Hour
30 40 45 55watts watts watts wattsMotor Rating @ 2000 r.p.m.
Cont 1 Hour Cont 1 Hour
45 55 65 80watts watts watts wattsMotor Rating @ 3000 r.p.m.
Cont 1 Hour Cont 1 Hour
60 75 90 110watts watts watts wattsMotor Rating @ 4000 r.p.m.
PM 10 S PM 11 S PM 10 S PM 11 S PM 10 S PM 11 S PM 10 S PM 11 S
77
PM 10 S
70:166:160:154:148:144:140:136:133:130:127:125:1
22 1/2:120 1/2:118 1/2:116 1/2:115 1/2:114 1/2:113 1/2:112 1/2:111 1/3:110 1/3:19 1/3:18 1/3:17 1/4:16 1/4:15 1/6:14 1/8:1
2223252831343842455056606773819197103113120132145161180207243293364
1.51.52.32.32.32.32.11.91.81.71.51.51.51.31.21.21.11.10.90.90.90.80.70.70.70.50.40.3
––––––
2.72.42.32.11.91.91.91.61.51.41.41.31.21.11.11
0.90.80.80.60.50.4
1.51.52.32.32.32.32.92.92.92.82.52.52.42.22
1.91.81.71.61.41.41.31.21.11.10.90.60.5
2830333742455056616774808998108121129138150160176194214240276324390485
––––––
2.52.22.12
1.81.71.71.51.41.31.31.21.111
0.90.90.80.70.60.40.3
––––––
2.92.32.72.52.22.22.11.91.71.71.61.51.41.31.21.11.11
0.90.70.50.4
–––––––
2.92.92.72.52.32.42.12
1.91.81.71.61.41.41.31.21.11.10.80.60.5
–––––––––––
2.92.92.62.42.32.22.12
1.81.71.61.51.41.31
0.80.6
434550566368758391100111120133146162182194207225240265290321360414487585727
––––––
2.52.22.12
1.81.71.71.51.41.31.31.21.111
0.90.90.80.70.60.40.3
––––––
2.92.82.72.52.22.22.11.91.71.71.61.51.41.31.21.11.11
0.90.70.50.4
––––––––
2.92.82.52.52.42.12
1.91.81.71.61.41.41.31.21.11
0.80.60.5
––––––––––––
2.92.62.42.32.222
1.71.71.61.51.41.31
0.80.6
576167748391100111121133148160178195216242258276300320353387429480552649780970
––––––
2.52.22.12
1.81.71.71.51.41.31.31.21.111
0.90.90.80.70.60.40.3
––––––
2.92.82.72.52.22.22.11.91.71.71.61.51.41.31.21.11.11
0.90.70.50.4
–––––––––––
2.92.92.62.42.32.22.12
1.81.71.61.51.41.31
0.80.6
PM 10 SPM 11 S
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 10 S
Optional shaft at motor speed (lead end only) 7.93mm dia.�33mm long.Approx. weight: PM 10 S – 1.50 Kg
PM 11 S – 1.96 Kg
9mm dia. h6.Flat 6mm�19mm long.
3 mounting feet tappedM5�10mm deep.
Leads out here 30cm
Single Reduction Worm Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosures: Totally Enclosed (IP 54)
Gearbox Type:
SSpeed Range: 22 – 970 r.p.m.
� Voltage, Construction, Connections, Motor PerformanceSpecifications and Optional Extras see page 74 for full details.
(1 Nm = 8.85 lbs. ins.) (1 Nm = 10.2 cmkp)
Per
man
ent
Mag
net
Single Reduction Worm Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosures: Totally Enclosed (IP 54)
Gearbox Type:
M or MBSpeed Range: 25 – 970 r.p.m.
78
PM 11 MB PM 11 MFPM 11 M
� Voltage, Construction, Connections, Motor PerformanceSpecifications and Optional Extras see pages 72 and 74 for full details
. Hollow shaft. Available on request. Maximum internal diameter 8mm.
(1 Nm = 8.85 lbs. ins.) (1 Nm = 10.2 cmkp)
5.85
4.33.83.73.4333
2.62.42.32.22.12
1.71.71.61.51.41.31
0.80.6
4.74
3.53.13
2.82.52.52.42.12
1.91.81.71.61.41.41.31.21.11
0.80.60.5
3.73.53.12.82.72.52.22.22.11.91.71.71.61.51.41.31.21.11.11
0.90.70.50.4
5.85
4.33.83.73.4333
2.62.42.32.22.12
1.71.71.61.51.41.31
0.80.6
4.74
3.53.13
2.82.52.52.42.12
1.91.81.71.61.41.41.31.21.11
0.80.60.5
COMPOSITE
OUTPUT TORQUE (Nm)FINALR.P.M.
FINALR.P.M.
FINALR.P.M.
FINALR.P.M.
GEARBOXRATIO
OUTPUT TORQUE (Nm) OUTPUT TORQUE (Nm) OUTPUT TORQUE (Nm)
COMPOSITE COMPOSITE COMPOSITE
Cont 1 Hour Cont 1 Hour
20 25 33 40watts watts watts wattsMotor Rating @ 1500 r.p.m.
Cont 1 Hour Cont 1 Hour
30 40 45 55watts watts watts wattsMotor Rating @ 2000 r.p.m.
Cont 1 Hour Cont 1 Hour
45 55 65 80watts watts watts wattsMotor Rating @ 3000 r.p.m.
Cont 1 Hour Cont 1 Hour
60 75 90 110watts watts watts wattsMotor Rating @ 4000 r.p.m.
M/MBPM 10
M/MBPM 11
M/MBPM 10
M/MBPM 11
M/MBPM 10
M/MBPM 11
M/MBPM 10
M/MBPM 11
60:148:140:136:133:130:127:125:1
22 1/2:120 1/2:118 1/2:116 1/2:115 1/2:114 1/2:113 1/3:112 1/3:111 1/3:110 1/3:19 1/3:18 1/3:17 1/4:16 1/6:15 1/8:14 1/8:1
25313842455056606773819197103113120132145161180207243293364
2.92.52.11.91.81.71.51.51.51.31.21.11.111
0.90.80.80.70.70.60.50.40.3
3.63.12.72.42.32.11.91.91.91.61.51.41.41.31.21.111
0.90.80.80.60.40.3
4.84
3.53.23
2.82.52.52.42.22
1.91.81.71.61.41.41.31.21.11.10.80.60.5
33425056616774808998108121129138150160176194214240276324390485
32.82.52.22.12
1.81.71.71.51.41.31.31.21.111
0.90.90.80.70.60.40.3
3.73.53.12.82.72.52.22.22.11.91.71.71.61.51.41.31.21.11.11
0.90.70.50.4
4.74
3.53.13
2.82.52.52.42.12
1.91.81.71.61.41.41.31.21.11
0.80.60.5
5.85
4.33.83.73.4333
2.62.42.32.22.12
1.71.71.61.51.41.31
0.80.6
5063758391100111120133146162182194207225240265290321360414487585727
32.82.52.22.12
1.81.71.71.51.41.31.31.21.111
0.90.90.80.70.60.40.3
3.73.53.12.82.72.52.22.22.11.91.71.71.61.51.41.31.21.11.11
0.90.70.50.4
6683100111121133145160178195216242258276300320353387429480552648780970
32.82.52.22.12
1.81.71.71.51.41.31.31.21.111
0.90.90.80.70.60.40.3
5.84.54.33.93.73.43.13.13
2.62.42.32.22.12
1.81.71.61.51.41.31
0.80.6
34
Ø 66
35.5
58.7
103
69
34
52
PM 11 M = 204PM 10 M = 185
25 10
35
4549.8PM 10 = 66PM 11 = 85
1010.7
79
PM 10 MPM 11 M
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 10 M
Optional shaft at motor speed (lead end only) 7.93mm dia.�33mm long.Approx. weight: PM 10 M – 1.8 Kg
PM 11 M – 2.1 Kg
Leads out here 30cm
12mm dia. h6.Keyway 4mm�38mm long.Alternative, hollow shaft8mm inside diameter.
3 mounting feet tappedM5�10mm deep.
52
121
7
58.6
3550
.8
78
55.5
SLOT
81
15 x 7.2
55.4
40.5
PM 10 MB = 192 PM 11 MB = 211
Ø 66
PM 10 = 66
1010.7
PM 11 = 8549.8
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 10 MB
Optional shaft at motor speed (lead end only) 7.93mm dia.�33mm long.Approx. weight: PM 10 MB – 2.02 Kg
PM 11 MB – 2.48 Kg
Leads out here 30cm
12mm dia. h6.Keyway 4mm�38mm long.Alternative, hollow shaft8mm inside diameter.
PM 10 MBPM 11 MB
Per
man
ent
Mag
net
PM 60 M with terminal box PM 1 MB PM 1 MF
Single Reduction Worm Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosures: – PM 1–PM 2–PM 6 – Drip Proof Internal Fan Cooled (IP 21)PM 3–PM 4–PM 5 – Totally Enclosed (IP 54)
Gearbox Type:
M or MBSpeed Range: 25 – 970 r.p.m.
80
5.95.95
4.54.34
3.63.53.43.12.82.72.62.52.32.12
1.91.81.61.51.20.90.68
COMPOSITE
OUTPUT TORQUE (Nm)FINALR.P.M.
FINALR.P.M.
FINALR.P.M.
FINALR.P.M.
GEARBOXRATIO
OUTPUT TORQUE (Nm) OUTPUT TORQUE (Nm) OUTPUT TORQUE (Nm)
COMPOSITE COMPOSITE COMPOSITE
� Voltage, Construction, Connections, Motor PerformanceSpecifications and Optional Extras see pages 72 and 74 for full details.Hollow shaft available on request maximum internal diameter 8mm.
(1 Nm = 8.85 lbs. ins.) (1 Nm = 10.2 cmkp)
40 watts 50 watts 60 wattsMotor Rating @ 1500 r.p.m.
60 watts 80 watts 100 wattsMotor Rating @ 2000 r.p.m.
90 watts 120 watts 150 wattsMotor Rating @ 3000 r.p.m.
120 watts 160 watts 200 wattsMotor Rating @ 4000 r.p.m.
PM 1 M/MB PM 1 M/MB PM 1 M/MB PM 1 M/MBPM 3 M/MB PM 3 M/MB PM 3 M/MB PM 3 M/MBPM 4 M/MB PM 4 M/MB PM 4 M/MB PM 4 M/MBPM 5 M/MB PM 5 M/MB PM 5 M/MB PM 5 M/MB
PM 2 M/MB PM 2 M/MB PM 2 M/MB PM 2 M/MBPM 6 M/MB PM 6 M/MB PM 6 M/MB PM 6 M/MBCont
1 Hour
60:148:140:136:133:130:127:125:1
22 1/2:120 1/2:118 1/2:116 1/2:115 1/2:114 1/2:113 1/3:112 1/3:111 1/3:110 1/3:19 1/3:18 1/3:17 1/4:16 1/6:15 1/8:14 1/8:1
25313842455056606773819197103113120132145161180207243293364
5.45
4.54.13.83.63.33.13
2.82.52.42.32.22
1.91.81.71.61.51.41
0.80.6
5.95.65
4.54.34
3.63.53.43.12.82.72.62.52.32.12
1.91.81.61.51.20.90.68
5.95.65
4.54.34
3.63.53.43.12.82.72.62.52.32.12
1.91.81.61.51.20.90.68
5.95.95.34.74.54.23.83.73.63.32.92.82.72.62.42.22.12
1.81.71.61.30.90.7
5.95.96.35.65.45
4.54.44.33.93.53.43.33.12.92.62.52.42.22
1.91.51.10.85
––
6.35.65.45
4.54.44.33.93.53.43.33.12.92.62.52.42.22
1.91.51.10.85
––
6.35.65.45
4.54.44.33.93.53.43.33.12.92.62.52.42.22
1.91.51.10.85
5.95.96.45.65.45
4.64.44.33.93.53.43.23.12.92.62.52.42.22
1.91.61
0.84
––
7.87
6.76.25.65.55.44.84.44.24
3.83.63.23.13
2.72.52.41.91.41.1
––
7.87
6.76.25.65.55.44.84.44.24
3.83.63.23.13
2.72.52.41.91.41.1
––
7.87
6.76.25.65.55.44.84.44.24
3.83.63.23.13
2.72.52.41.91.41.1
33425056616774808998110121129138150160176194214240276324390485
5063758391100111120133146162182194207225240265290321360414487585727
6683100111121133148160178195216242258276300320353387429480552649780970
60:148:140:136:133:130:125:1
20 1/2:115 1/2:112 1/3:18 1/3:17 1/4:15 1/8:14 1/8:1
253138424550607397122180207292364
--
7.26.76.25.95.44.63.83.32.52.31.71.4
7.97.9---
GEARBOXRATIO
FINALRPM
GearboxSpecificationMotor Speed1500 r.p.m.
CONTMotor Rating
65 watts
1 HOURMotor Rating
85 watts
15 MINMotor Rating
120 watts
CONTMotor Rating
85 watts
1 HOURMotor Rating
110 watts
15 MINMotor Rating
155 watts
PM 50 M or MB PM 60 M or MB
COMPOSITE BRONZE
-----
7.77.16.15.04.33.22.92.21.8
7.97.99.58.88.1---
COMPOSITE BRONZE
--------
7.16.14.64.23.12.6
7.97.911.811.811.410.810.08.6---
COMPOSITE BRONZE
-----
7.77.16.15.04.33.22.92.21.8
7.97.99.58.88.1---
COMPOSITE BRONZE
--------
6.55.64.23.82.92.4
7.97.911.811.310.59.99.17.7---
COMPOSITE BRONZE
----------
5.95.44.13.3
7.97.911.811.811.811.811.811.19.17.9---
COMPOSITE BRONZE
OUTPUT TORQUE (Nm)
CONTMotor Rating
140 watts
15 MINMotor Rating
230 watts
PM 60 MB = 277PM 50 MB = 264
Ø 77
15°
PM 3 MB = 221PM 1/4 MB = 234PM 2/5 MB = 247PM 6 MB = 259
52
126
7
58.6
3550
.8
78
55.5SLOT
81
15 x 7.2
55.4
40.5
68.5
71
PM 50 = 112.7PM 60 = 125.4
PM 3 = 69.5PM 1/4 = 82PM 2/5 = 95PM 6 = 107.6
1111
PM 50 M = 258PM 60 M = 270
PM 3 M = 214PM 1/4 M = 227
40.5
40
15°
Ø 77
58.7
109
75
34
52
PM 6 M = 252PM 2/5 M = 240
71PM 50 = 112.7PM 60 = 125.4
PM 3 = 69.5PM 1/4 = 82PM 2/5 = 95PM 6 = 107.6
1111
11
51
40
29
68.5
PM 1 M – PM 2 MPM 3 M – PM 4 MPM 5 M – PM 6 M
PM 50 M – PM 60 M
PM 1 MB – PM 2 MBPM 3 MB – PM 4 MBPM 5 MB – PM 6 MB
PM 50 MB – PM 60 MB
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 1/4 M
Approx. weight: PM 1/3 M – 2.82 KgPM 2/4 M – 3.17 KgPM 5/6 M – 3.36 Kg
PM 50/60 M – 3.6 Kg
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 1/4 MB
Optional shaft at motor speed (lead end only) 10mm dia.�33mm.
Optional shaft at motor speed (lead end only) 10mm dia.�33mm long.
Approx. weight: PM 1/3 MB – 3.01 KgPM 2/4 MB – 3.36 KgPM 5/6 MB – 3.55 Kg
PM 50/60 MB – 3.8 Kg
81
5062758391100120146193243360414585727
-----
7.26.55.64.64.03.02.72.01.7
7.97.98.88.07.8---
CONTMotor Rating
155 watts
1 HourMotor Rating
200 watts
15 MINMotor Rating
280 watts
CONTMotor Rating
210 watts
1 HourMotor Rating
255 watts
15 MINMotor Rating
345 watts
PM 50 M/MB PM 60 M/MB
COMP. BRONZE
-------
7.25.95.13.93.52.62.2
7.97.911.310.310.09.38.4---
COMP. BRONZE
---------
7.05.34.83.53.0
7.97.911.811.811.811.811.59.98.1---
COMP. BRONZE
-------
7.56.15.34.03.62.72.3
7.97.911.710.710.49.68.7---
COMP. BRONZE
--------
7.46.54.94.43.22.8
7.97.911.811.811.811.710.59.1---
COMP. BRONZE
----------
6.65.94.43.7
7.97.911.811.811.811.811.811.810.18.8---
COMP. BRONZE
Single Reduction Worm Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosures: – PM 50 – Totally Enclosed (IP 54)PM 60 – Drip Proof Internal Fan Cooled (IP 21)
Gearbox Type:
M/MBSpeed Range: 25 – 970 r.p.m.
60:148:140:136:133:130:125:1
20 1/2:115 1/2:112 1/3:18 1/3:17 1/4:15 1/8:14 1/8:1
3342505661678097129162240275390485
-----
7.26.55.64.64.03.02.72.01.7
7.97.98.88.07.8---
GEABOXRATIO
FINALR.P.M.
CONTMotor Rating
105 watts
1 HourMotor Rating
135 watts
15 MINMotor Rating
185 watts
1 HourMotor Rating
170 watts
PM 50 M/MB PM 60 M/MB
COMP.
Note: with 4000 r.p.m. motor speeds up to 970 r.p.m. available.
BRONZE
-------
7.25.95.13.93.52.62.2
7.97.911.310.310.09.38.4---
COMP. BRONZE
---------
7.05.34.83.53.0
7.97.911.811.811.811.811.59.98.1---
COMP. BRONZE
-------
7.56.15.34.03.62.72.3
7.97.911.710.710.49.68.7---
COMP. BRONZE
--------
7.46.54.94.43.22.8
7.97.911.811.811.811.710.59.1---
COMP. BRONZE
----------
6.65.94.43.7
7.97.911.811.811.811.811.811.810.18.8---
COMP. BRONZE
Motor Speed 3000 r.p.m.
OUTPUT TORQUE (Nm)
Optional terminal box tapped 20mm conduit or PG 13.5on request. Standard position entry R.H.S.
On request, 3 mounting feetcan be drilled and tapped M5
12mm dia. h6.Keyway 4mm�38mm long.Alternative, hollow shaft 8mminside diameter.
12mm dia. h6.Keyway 4mm�38mm long.Alternative, hollow shaft8mm inside diameter.
Leads out here 30cm
Leads out here 30cm
Optional terminal box tapped 20mm conduit or PG 13.5on request. Standard position entry R.H.S.
Per
man
ent
Mag
net
OUTPUT TORQUE (Nm)
Motor Speed 2000 r.p.m.
FINALR.P.M.
Single Reduction Worm Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosures: – PM 2 – PM 6 – Drip Proof Internal Fan Cooled (IP 21)PM 4 – PM 5 – Totally Enclosed (IP 54)
Gearbox Type:
L/LB/LH/LHBSpeed Range: 25 – 780 r.p.m.
82
PM 5 LB PM 60 LH
8.57.66.75.15
4.33.53
2.52
1.5
8.57.66.75.15
4.33.53
2.52
1.5
10.79
8.46.46.25.44.43.83
2.51.9
10.79
8.46.46.25.44.43.83
2.51.9
OUTPUT TORQUE (Nm)FINALR.P.M.
FINALR.P.M.
FINALR.P.M.
GEARBOXRATIO
� Voltage, Construction, Connections, Motor PerformanceSpecifications and Optional Extras see pages 72 and 74 for full details.LH/LHB for hollow shaft details see page 114.
(1 Nm = 8.85 lbs. ins.) (1 Nm = 10.2 cmkp)
COMPOSITE
FINALR.P.M.
OUTPUT TORQUE (Nm) OUTPUT TORQUE (Nm) OUTPUT TORQUE (Nm)
COMPOSITE COMPOSITE COMPOSITE
PM 2 PM 2 PM 2 PM 2PM 6 PM 6 PM 6 PM 6PM 4 PM 4
L/LB/LH/LHBPM 4
L/LB/LH/LHBPM 4
L/LB/LH/LHBPM 5
L/LB/LH/LHBL/LB/LH/LHBPM 5
L/LB/LH/LHBPM 5
L/LB/LH/LHBPM 5
L/LB/LH/LHB
Cont
1 Hour
60:150:140:130:125:1
20 1/2:115 1/3:112 1/3:19 1/4:17 1/6:15 1/8:1
25303750607397120160210293
7.57
6.35
4.44
3.32.62.21.91.1
98.47.66
5.34.74
3.22.62.31.3
3340506580100130160200279390
8.57.66.75.15
4.33.53
2.52
1.5
10.79
8.46.46.25.44.43.83
2.51.9
506075100120150200240320419585
6780100130160200260320400558780
60:150:140:130:125:1
20 1/2:115 1/3:112 13:19 1/4:17 1/6:15 1/8:1
253038506073100125166210293
9.38.27.25.95.44.63.83.32.72.21.7
---
GEARBOXRATIO
FINALRPM
GearboxSpecificationMotor Speed1500 r.p.m.
CONTMotor Rating
65 watts
1 HOURMotor Rating
85 watts
15 MINMotor Rating
120 watts
CONTMotor Rating
85 watts
1 HOURMotor Rating
110 watts
15 MINMotor Rating
155 watts
PM 50 L/LB/LH/LHB PM 60 L/LB/LH/LHB
COMPOSITE BRONZE
-10.89.57.77.16.15
4.33.62.82.2
12.1---
COMPOSITE BRONZE
--
13.410.8108.67.16
5.143
1715.2
---
COMPOSITE BRONZE
-10.89.57.77.16.15
4.33.62.82.2
12.1---
COMPOSITE BRONZE
--
12.39.99.17.96.55.54.63.72.8
15.713.9
---
COMPOSITE BRONZE
---
1412.911.19.17.86.55.23.9
1717
14.6---
COMPOSITE BRONZE
OUTPUT TORQUE (Nm)
60:150:140:130:125:1
20 1/2:115 1/3:112 1/3:19: 1/4:17 1/6:15 1/8:1
334050678098133167222279390
11.2108.86.76.55.64.64
3.32.62
---
GEARBOXRATIO
FINALRPM
GearboxSpecificationMotor Speed2000 r.p.m.
CONTMotor Rating
105 watts
1 HOURMotor Rating
135 watts
15 MINMotor Rating
185 watts
CONTMotor Rating
140 watts
1 HOURMotor Rating
170 watts
15 MINMotor Rating
230 watts
PM 60 L/LB/LH/LHB
COMPOSITE BRONZE
--
11.38.78.47.26
5.14.33.42.6
14.412.8
---
COMPOSITE BRONZE
-----
9.98.27.05.84.63.5
1717
15.511.911.5
---
COMPOSITE BRONZE
--
11.79
8.77.56.25.34.43.52.7
1513.3
---
COMPOSITE BRONZE
--
14.210.910.69.17.56.45.44.23.2
1716.1
---
COMPOSITE BRONZE
----
14.312.310.28.77.35.74.4
1717
19.214.7
---
COMPOSITE BRONZE
OUTPUT TORQUE (Nm)
PM 50 L/LB/LH/LHB
50 watts 60 wattsMotor Rating @ 1500 r.p.m.
80 watts 100 wattsMotor Rating @ 2000 r.p.m.
120 watts 150 wattsMotor Rating @ 3000 r.p.m.
160 watts 200 wattsMotor Rating @ 4000 r.p.m.
PM 60 L = 308PM 50 L = 295
Ø 7
7
PM 4 L = 264
40.6
40
15°
51
84.4
137
51 75.5
Ø 88
PM 6 L = 290PM 2/5 L = 277
PM 50 = 112.7PM 60 = 125.4
PM 4 = 82PM 2/5 = 95PM 6 = 107.6
1111
11
51
40
29
88.9
71
PM 2 L – PM 4 LPM 5 L – PM 6 L
PM 50 L – PM 60 L
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 4 L
Optional shaft at motor speed (lead end only) 10mm dia.�33mm long.
Approx. weight: PM 2/4 L – 3.97 KgPM 5/6 L – 4.16 Kg
PM 50/60 L – 4.41 Kg
PM 50 LB = 295PM 60 LB = 308
Ø 88
75.5
51
40.6
15°
60.2
70
90
7.4
44.4
149
51
SLOT70
17 x 7.2
100
PM 2/5 LB = 277PM 6 LB = 290
PM 4 LB = 264
88.9
71
Ø 7
7
PM 50 = 112.7PM 60 = 125.4
PM 4 = 82PM 2/5 = 95PM 6 = 107.6
1111
PM 2 LB – PM 4 LB PM 5 LB – PM 6 LB
PM 50 LB – PM 60 LB
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 4 LB
Optional shaft at motor speed (lead end only) 10mm dia.�33mm long.
Approx. weight: PM 2/4 LB – 4.16 KgPM 5/6 LB – 4.35 Kg
PM 50/60 LB – 4.6 Kg
83
Single Reduction Worm Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosures: – PM50 – Totally Enclosed (IP 54)PM60 – Drip Proof Internal Fan Cooled (IP 21)
Gearbox Type:
L/LB/LH/LHBSpeed Range: 25-780* r.p.m.
*Note: with 4000 r.p.m. motor speeds up to 780 r.p.m. available.
For hollow shaft details see page 114.
Optional terminal box tapped 20mmconduit or PG 13.5 on request.Standard entry position R.H.S.
Optional terminal box tapped 20mm conduit or PG 13.5on request. Standard entry position R.H.S.
Leads out here 30cm
Leads out here 30cm
15mm dia. h6.Keyway 5mm�38mm long.Alternative, LH gearboxwith 15mm inside dia. hollowshaft (25mm external dia.).Also available with solidshaft up to 25mm dia.Length as required.
15mm dia. h6.Keyway 5mm�38mm long.Alternative, LHB gearbox with15mm inside dia. hollow shaft(25mm external dia.). Alsoavailable with solid shaft up to25mm dia. Length as required.
On request, 3 mounting feet can bedrilled and tapped M5.
60:150:140:130:125:1
20 1/2:115:112:19:1
7 1/6:15 1/8:1
506075100120146200250333419585
11.2108.86.76.55.64.64
3.32.62
---
GEARBOXRATIO
FINALRPM
GearboxSpecificationMotor Speed3000 r.p.m.
CONTMotor Rating
155 watts
1 HOURMotor Rating
200 watts
15 MINMotor Rating
280 watts
CONTMotor Rating
210 watts
1 HOURMotor Rating
255 watts
15 MINMotor Rating
345 watts
PM 50 L/LB/LH/LHB PM 60 L/LB/LH/LHB
COMPOSITE BRONZE
--
11.38.78.47.26
5.14.33.42.6
14.412.8
---
COMPOSITE BRONZE
-----
9.98.27.05.84.63.5
1717
15.511.911.5
---
COMPOSITE BRONZE
--
11.79
8.77.56.25.34.43.52.7
1513.3
---
COMPOSITE BRONZE
--
14.210.910.69.17.56.45.44.23.2
1716.1
---
COMPOSITE BRONZE
----
14.312.310.28.77.35.74.4
1717
19.214.7
---
COMPOSITE BRONZE
OUTPUT TORQUE (Nm)
Per
man
ent
Mag
net
FINALR.P.M. BRONZE BRONZE BRONZE BRONZE
OUTPUT TORQUE (Nm) OUTPUT TORQUE (Nm) OUTPUT TORQUE (Nm) OUTPUT TORQUE (Nm)
COMPOSITE COMPOSITE COMPOSITE COMPOSITECOMPOSITE COMPOSITE COMPOSITE COMPOSITEBRONZE BRONZE BRONZE BRONZE*RATIO
Double Reduction Worm Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosure: Totally Enclosed (IP 54)
Gearbox Type:
SSSpeed Range: 1 – 80 r.p.m.
� Voltage, Construction, Connections, Motor PerformanceSpecifications and Optional Extras see pages 72 and 74 for full details.
(1 Nm = 8.85 lbs. ins.) (1 Nm = 10.2 cmkp)
GearboxSpecification
Motor Speed1500 r.p.m.
Cont
Motor Rating7.5 watts
Cont
Motor Rating12.5 watts
Cont
Motor Rating19 watts
Cont
Motor Rating20 watts
PM 7 SS PM 8 SS PM 9 SS PM 10 SS1 Hour
Motor Rating10 watts
1 Hour
Motor Rating15 watts
1 Hour
Motor Rating24 watts
1 Hour
Motor Rating25 watts
1234510152025304050
1485:1750:1500:1375:1300:1150:1101:175:160:152:137:130:1
444443
2.21.81.61.41.10.9
5.95.95.95.64.7–––
444444
2.92.42.11.91.41.2
5.95.95.95.95.94–––
–––––4
3.73
2.62.31.81.5
––––
5.95–––
–––––44
3.63.12.82.11.8
–––––
5.94.4–––
––––––444
3.52.72.2
––––––
5.64.64–––
––––––4444
3.42.8
––––––
5.95.85
4.5––
–––––––––
3.62.82.3
––––––––––––
–––––––––44
3.6
––––––––
5.95.5––
PM 10 SSPM 8 SS
2847.3
2944
88
34
59.4
Ø 66
35.5
29
PM 10 SS = 192
PM 10 = 66
10
45
35
251010.7
62.4
PM 10 SSDimensions in mm. Scale 1:4
Optional shaft at motor speed (lead end only) 7.93mm dia.�33mm long. Approx. weight: PM 10 SS – 1.93 Kg
9mm dia. h6.Flat 6mm�19mm long.
3 mounting feet tappedM5�10mm deep.
Leads out here 30cm
42.5
30
4429
PM 7 SS = 169PM 8 SS = 182PM 9 SS = 195
Ø 56
2847.3
84
55.4
29
PM 7 = 47
9
PM 8 = 60PM 9 = 73
10
45
35
259
61.5
PM 7 SSPM 8 SSPM 9 SS
Dimensions in mm. Scale 1:4NB: unit drawn is PM 8 SS
Optional shaft at motor speed (lead end only) 7.93mm dia.�33mm long.
Approx. weight: PM 7 SS – 1.3 KgPM 8 SS – 1.5 KgPM 9 SS – 1.7 Kg
9mm dia. h6.Flat 6mm�19mm long.
3 mounting feet tappedM4�10mm deep.
Leads out here 30cm(flexible grommet).
FINALR.P.M. BRONZE BRONZE BRONZE BRONZE
OUTPUT TORQUE (Nm) OUTPUT TORQUE (Nm) OUTPUT TORQUE (Nm) OUTPUT TORQUE (Nm)
COMPOSITE COMPOSITE COMPOSITE COMPOSITECOMPOSITE COMPOSITE COMPOSITE COMPOSITEBRONZE BRONZE BRONZE BRONZE*RATIO
GearboxSpecification
Motor Speed2000 r.p.m.
Cont
Motor Rating10 watts
Cont
Motor Rating17 watts
Cont
Motor Rating25 watts
Cont
Motor Rating30 watts
PM 7 SS PM 8 SS PM 9 SS PM 10 SS1 Hour
Motor Rating13 watts
1 Hour
Motor Rating21 watts
1 Hour
Motor Rating33 watts
1 Hour
Motor Rating40 watts
10152025304050607580
196:1134:198:180:165:152:143:134:127:126:1
3.72.72.21.81.61.41.21
0.80.8
–––
43.52.92.42.11.81.51.31.11
4.8–––
44
3.93.22.82.42.11.71.41.4
5.94.7–––
–444
3.73.22.72.31.91.8
–5.95.14.2–––
––444
3.53
2.522
––
5.64.64.1–––
––4444
3.93.22.72.6
––
5.95.95.44.6–––
–––––44
2.72.32.2
–––
5.24.74–––
––––––4
3.63.13
––––
5.95.34.3–––
84
Double Reduction Worm Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosure: – Totally Enclosed (IP 54)
� Voltage, Construction, Connections, Motor PerformanceSpecifications and Optional Extras see pages 72 and 74 for full details.
BRONZE
OUTPUT TORQUE (Nm)FINALR.P.M. COMPOSITE COMPOSITEBRONZE
GEARBOXRATIO
(1 Nm = 8.85 lbs. ins.) (1 Nm = 10.2 cmkp)
GearboxSpecification
Motor Speed2000 r.p.m.
Cont
Motor Rating30 watts
PM 10 MBM1 Hour
Motor Rating40 watts
12345810152025
2480:11296:1675:1412:1400:1250:1198:1134:1102:180:1
9999999
7.46.55.2
11.811.811.811.811.811.8
–––
99999999
8.66.9
11.811.811.811.811.811.811.89.7––
PM 10 MBM
85
Gearbox Type:
MBMSpeed Range: 1 – 25 r.p.m.
78
55.5
81
55.4
Ø 66
5258
.7
3462.3
121
69
7
3550
.8
SLOT15 x 7.2
34
35.5
220PM 10 MBMDimensions in mm. Scale 1:4
Optional shaft at motor speed (lead end only) 7.93mm dia.�33mm long. Approx. weight: PM 10 MBM – 2.70 Kg
12mm dia. h6.Keyway 4mm�38mm long.Alternative, hollow shaft8mm inside diameter.
Leads out here 30cm
Per
man
ent
Mag
net
BRONZE BRONZE BRONZE BRONZE
OUTPUT TORQUE (Nm)FINALR.P.M.
In Line Double Reduction Worm Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosure: – Totally enclosed (IP 54)
Gearbox Type:
SIWSpeed Range: 1.5 – 176 r.p.m.
PM 10 SIWPM 8 SIW
� Voltage, Construction, Connections, Motor PerformanceSpecifications and Optional Extras see pages 72 and 74 for full details.Minimum speed of 0.3 r.p.m. obtainable with motor speed of 1500 r.p.m. on request.
(1 Nm = 8.85 lbs. ins.) (1 Nm = 10.2 cmkp)
COMPOSITE COMPOSITE COMPOSITE COMPOSITE COMPOSITE COMPOSITECOMPOSITE COMPOSITE COMPOSITE COMPOSITEBRONZE BRONZE BRONZE BRONZE BRONZE BRONZE
RATIO
INT FINAL
GearboxSpecification
Motor Speed2000 r.p.m.
Cont
Motor Rating10 watts
Cont
Motor Rating17 watts
Cont
Motor Rating25 watts
Cont
Motor Rating30 watts
Cont
Motor Rating45 watts
1 Hour
Motor Rating13 watts
1 Hour
Motor Rating21 watts
1 Hour
Motor Rating33 watts
1 Hour
Motor Rating40 watts
1 Hour
Motor Rating55 watts
PM 7 SIW PM 8 SIW PM 9 SIW PM 10 SIW PM 11 SIW
1.53
5.510151923262933384651627594118
54:127:1
14 1/2:18 1/3:116 1/2:112 1/2:110 1/3:19 1/3:18 1/3:17 1/4:16 1/4:15 1/6:16 1/4:15 1/6:15 1/6:14 1/8:14 1/8:1
25:125:125:125:1
8 1/3:18 1/3:18 1/3:18 1/3:18 1/3:18 1/3:18 1/3:18 1/3:16 1/4:16 1/4:15 1/6:15 1/6:14 1/8:1
77
5.53.72.82.32
1.91.71.61.41.21.11
0.80.70.6
118.3–––
––7
4.83.63
2.62.42.32
1.81.51.51.21.10.90.7
–10.87.2–––
––7
6.54.84.13.53.33
2.72.42.12
1.71.41.21
–119.7–––
––77
6.35.44.74.34
3.63.22.72.62.21.91.51.3
––
118.5–––
–––7
6.95.95.14.74.43.93.53
2.82.42
1.71.4
––
119.3–––
––––77
6.76.25.75.24.63.93.73.22.72.21.8
–––
119.17.7–––
––––7
6.56.15.65.24.74.23.63.42.92.42
1.7
–––
10.58.1–––
––––––777
6.35.64.84.53.83.32.72.2
––––
10.88.67.87.1–––
––––––––7
5.65
4.24
3.42.92.42
––––
119.68.88
7.1–––
––––––––7
6.86.15.24.94.23.52.92.4
–––––
1110.89.78.68.27.1–––
BRONZE BRONZE BRONZE BRONZE
OUTPUT TORQUE (Nm)FINALR.P.M. COMPOSITE COMPOSITE COMPOSITE COMPOSITE COMPOSITE COMPOSITECOMPOSITE COMPOSITE COMPOSITE COMPOSITEBRONZE BRONZE BRONZE BRONZE BRONZE BRONZE
RATIO
INT FINAL
GearboxSpecification
Motor Speed3000 r.p.m.
Cont
Motor Rating15 watts
Cont
Motor Rating25 watts
Cont
Motor Rating38 watts
Cont
Motor Rating45 watts
Cont
Motor Rating65 watts
1 Hour
Motor Rating20 watts
1 Hour
Motor Rating33 watts
1 Hour
Motor Rating45 watts
1 Hour
Motor Rating55 watts
1 Hour
Motor Rating80 watts
PM 7 SIW PM 8 SIW PM 9 SIW PM 10 SIW PM 11 SIW
2481422293539435870778793112141176
54:127:1
14 1/2:18 1/3:116 1/2:112 1/2:110 1/3:19 1/3:18 1/3:16 1/4:15 1/6:16 1/4:14 1/8:15 1/6:15 1/6:14 1/8:14 1/8:1
25:125:125:125:1
8 1/3:18 1/3:18 1/3:18 1/3:18 1/3:18 1/3:18 1/3:16 1/4:18 1/3:16 1/4:15 1/6:15 1/6:14 1/8:1
77
5.53.72.82.32
1.91.71.41.21.111
0.80.70.6
118.3–––
––7
4.93.73.12.72.52.31.91.61.51.31.31.10.90.7
–117.4–––
––7
6.24.63.93.43.12.92.32
1.91.61.61.41.10.9
––
9.2–––
–––7
6.15.24.54.13.83.12.62.52.22.11.81.51.2
––
118.2–––
–––7
6.95.95.14.74.43.53
2.82.52.42
1.71.4
–––––––––––––––––
––––7
6.55.95.34.74.53.93.43.12.62.31.81.5
––––
8.37–––
––––7
6.55.95.34.74.53.93.43.12.62.31.81.5
––––
8.37––
––––––7
6.56.24.84.13.83.43.12.72.21.8
––––
10.88.67.2–––
––––––777
5.64.84.54
3.73.22.62.1
––––
119.68.57.77.4–––
–––––––77
6.95.95.54.94.54
3.22.6
–––––
1110.49.49
6.95.95.55–––
PM 11 SIW
86
Ø 5
6
42.5
PM 7 SIW = 167
3232
77
95.6
41
6
3.68
85
Ø 2
0.4
Ø 3
5
66
5516.5
55
1111
PM 8 SIW = 180PM 9 SIW = 19229
51
PM 7 SIWPM 8 SIWPM 9 SIW
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 8 SIW
Optional shaft at motor speed (lead end only) 7.93mm dia.�33mm long.
PM 7 SIW – 1.5 KgApprox. weight: PM 8 SIW – 1.7 Kg
PM 9 SIW – 1.9 Kg
Leads out here 30cm(flexible grommet).
9mm dia. h6.Flat 6mm�19mm long.
4 holes on 41.3mm P.C.D.Can be tapped M5�5mm deep.
4 holes can be tappedM5�10mm deep.
87
Ø 6
6
35.5
3232
77
95.6
41
6
3.6885
Ø 2
0.4
Ø 3
5
66
5516.5
55
1111
PM 10 SIW = 182PM 11 SIW = 20129
51
PM 10 SIWPM 11 SIW
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 10 SIW
Optional shaft at motor speed (lead end only) 7.93mm dia.�33mm long.Approx. weight: PM 10 SIW – 2.13 Kg
PM 11 SIW – 2.59 Kg
Leads out here 30cm
9mm dia. h6.Flat 6mm�19mm long.
4 holes on 41.3mm P.C.D.Can be tapped M5�5mm deep.
4 holes can be tappedM5�10mm deep.
Per
man
ent
Mag
net
BRONZE
BRONZE
OUTPUT TORQUE (Nm)FINALR.P.M. COMPOSITE BRONZE COMPOSITE BRONZE COMPOSITE BRONZE COMPOSITE BRONZE COMPOSITE BRONZE COMPOSITE
RATIO
INT FINAL
In Line Double Reduction Worm Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosures: – PM 3 – PM 10 – PM 11 – Totally Enclosed (IP 54)PM 1 – Drip Proof Internal Fan Cooled (IP 21)
Gearbox Type:
MIWSpeed Range: 1.5 – 176 r.p.m.
� Voltage, Construction, Connections, Motor Performance Specifications and OptionalExtras see pages 72 and 74 for full details.Minimum speed of 0.3 r.p.m. obtainable with motor speed of 1500 r.p.m. on request.Maximum speed up to 235 r.p.m. obtainable with motor speed of 4000 r.p.m. on request.
(1 Nm = 8.85 lbs. ins.) (1 Nm = 10.2 cmkp)
GearboxSpecification
Motor Speed2000 r.p.m.
PM 10 MIW PM 11 MIW PM 3 MIW PM 1 MIWCont
Motor Rating30 watts
1 Hour
Motor Rating40 watts
Cont
Motor Rating45 watts
Cont
Motor Rating45 watts
Cont
Motor Rating60 watts
1 Hour
Motor Rating55 watts
1.53
5.510151923262933384652637595118
54:127:1
14 1/2:18 1/3:116 1/2:112 1/2:110 1/3:19 1/3:18 1/3:17 1/4:16 1/4:15 1/6:16 1/4:15 1/6:15 1/6:14 1/8:14 1/8:1
25:125:125:125:1
8 1/3:18 1/3:18 1/3:18 1/3:18 1/3:18 1/3:18 1/3:18 1/3:16 1/6:16 1/6:15 1/8:15 1/8:14 1/8:1
1717
15.910.58.16.55.95.34.74.53.93.43.12.62.31.81.5
2823.7
–––––
17171714
10.88.67.87.16.36
5.24.54.13.43
2.42
2828
21.2–––––
171717
15.812.29.68.88
7.16.75.85
4.63.83.42.72.2
2828
23.7––––
17171717
14.911.810.89.78.68.27.16.25.74.74.13.32.7
282828
19.2––––
171717
15.812.29.68.88
7.16.75.85
4.63.83.42.72.2
2828
23.7––––
1717171717
12.811.710.69.59
7.86.76.25.14.53.63
28282821–––
BRONZE
OUTPUT TORQUE (Nm)FINALR.P.M. COMPOSITE BRONZE COMPOSITE BRONZE COMPOSITE BRONZE COMPOSITE BRONZE COMPOSITE COMPOSITE
RATIO
INT FINAL
GearboxSpecification
Motor Speed3000 r.p.m.
PM 10 MIW PM 11 MIW PM 3 MIW PM 1 MIWCont
Motor Rating45 watts
1 Hour
Motor Rating55 watts
Cont
Motor Rating65 watts
Cont
Motor Rating68 watts
Cont
Motor Rating90 watts
1 Hour
Motor Rating80 watts
2.24.58.31522293539435770788794113142176
54:127:1
14 1/2:18 1/3:116 1/2:112 1/2:110 1/3:19 1/3:18 1/3:16 1/4:15 1/6:16 1/4:14 1/8:15 1/6:15 1/6:14 1/8:14 1/8:1
25:125:125:125:1
8 1/3:18 1/3:18 1/3:18 1/3:18 1/3:18 1/3:18 1/3:16 1/6:18 1/3:16 1/6:15 1/8:15 1/8:14 1/8:1
1717
15.910.58.16.55.95.35.13.93.43.12.72.62.31.81.5
2823.7
–––––
17171714
10.88.67.26.56.24.84.13.83.63.12.72.21.8
2828
21.2–––––
171717
15.211.69.68.57.77.35.64.84.54.13.73.22.62.1
2828
22.5––––
17171717
14.211.810.49.49
6.95.95.55
4.54
3.22.6
2828
27.718.7
––––
171717
15.311.79.68.98
7.75.95
4.74.33.83.42.72.2
2828
22.6––––
17171717
15.412.811.710.610.28.47.86.75.45.14.53.62.9
282828
20.3––
PM 3 MIW
88
Ø 66
35.5
124
94
38.1
56
113
Ø 2
6.3
Ø 3
8.1
5
11.5
47.5
15
70
30.7
15
46.6
53.5
35
PM 10 MIW = 189PM 11 MIW = 20852
PM 10 MIWPM 11 MIW
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 10 MIW
Optional shaft at motor speed (lead end only) 7.93mm dia.�33mm long.Approx. weight: PM 10 MIW – 2.87 Kg
PM 11 MIW – 3.35 Kg
89
4 holes on 47.6mm P.C.D.Can be tapped M5�6mm deep.
12mm dia. h6.Keyway 4mm�38mm long. 4 holes tapped M6�12mm deep.
Leads out here 30cm
Ø 77
40.6
15°
126
94
38.1
56
113
Ø 2
6.3
Ø 3
8.1
5
11.5
47.5
15
70
30.7
15
46.6
53.5
35
PM 1 MIW = 232PM 3 MIW = 21952
71
PM 1 MIWPM 3 MIW
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 1 MIW
Optional shaft at motor speed (lead end only) 10mm dia.�33mm long. Approx. weight: PM 1/3 MIW – 3.86 Kg
4 holes on 47.6mm P.C.D.Can be tapped M5�6mm deep.
Optional terminal box tapped 20mmconduit or PG 13.5 on request.Standard entry position R.H.S.
12mm dia. h6.Keyway 4mm�38mm long.
4 holes tapped M6�12mm deep.
Leads outhere 30cm
Per
man
ent
Mag
net
Mot
or C L
Mot
or C L
BRONZE
OUTPUT TORQUE (Nm)FINALR.P.M.
BRONZE
OUTPUT TORQUE (Nm)FINALR.P.M. COMPOSITE COMPOSITE COMPOSITE COMPOSITE COMPOSITE COMPOSITEBRONZE BRONZE BRONZE BRONZE BRONZE
RATIO
INT FINAL
In Line Double Reduction Worm Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosures: – PM 2 – PM 6 – Drip Proof Internal Fan Cooled (IP 21)PM 4 – PM 5 – Totally Enclosed (IP 54)
Gearbox Type:
LIWSpeed Range: 1.6 – 81 r.p.m.
� Voltage, Construction, Connections, Motor PerformanceSpecifications and Optional Extras see pages 72 and 74 for full details.
(1 Nm = 8.85 lbs. ins.) (1 Nm = 10.2 cmkp)
GearboxSpecification
Motor Speed2000 r.p.m.
PM 4 LIW PM 2 LIW PM 6 LIW PM 5 LIWCont
Motor Rating60 watts
1 Hour
Motor Rating80 watts
Cont
Motor Rating80 watts
30 Min
Motor Rating120 watts
Cont
Motor Rating100 watts
1 Hour
Motor Rating100 watts
1.62.22.73.65681213192025294152
60:144:136:127:1
20 1/2:116 1/2:112 1/3:18 1/3:17 1/4:15 1/8:110 1/3:18 1/3:17 1/4:15 1/8:14 1/8:1
20 1/2:120 1/2:120 1/2:120 1/2:120 1/2:120 1/2:120 1/2:120 1/2:120 1/2:120 1/2:1
9:19:19:19:19:1
282828282828261917131311975
454545453631–––
2828282828282826221717141297
45454545454032–––
2828282828282826221717141297
45454545454032–––
282828282828282828262622181411
454545454545453834–––
28282828282828282721211715119
4545454545454030–––
28282828282828282721211715119
4545454545454030–––
COMPOSITE COMPOSITE COMPOSITE COMPOSITEBRONZE BRONZE BRONZE
RATIO
INT FINAL
GearboxSpecification
Motor Speed3000 r.p.m.
PM 2 LIW PM 4 LIW PM 6 LIW PM 5 LIWCont
Motor Rating120 watts
1 Hour
Motor Rating120 watts
Cont
Motor Rating150 watts
1 Hour
Motor Rating150 watts
2.43.34
5.479121820293240466581
60:144:136:127:1
20 1/2:116 1/2:112 1/3:18 1/3:17 1/4:15 1/8:110 1/3:18 1/3:17 1/4:15 1/8:14 1/8:1
20 1/2:120 1/2:120 1/2:120 1/2:120 1/2:120 1/2:120 1/2:120 1/2:120 1/2:120 1/2:1
9:19:19:19:19:1
28282828282828252317161413108
45454545454134–––
28282828282828252317161413108
45454545454134–––
282828282828282828222017161210
454545454545423129–––
282828282828282828222017161210
454545454545423129–––
PM 4 LIW + T/BoxPM 2 LIW with brake
90
91
Ø 77
40.6
15°
129
135
149
52.5
146
Ø 4
5.8
Ø 3
3.3
69.5
18.918.9
40.5
100
58
13.1
7.3
78
60
51
60PM 2/5 LIW = 264PM 6 LIW = 276
PM 4 LIW = 251
71
PM 2 LIW – PM 4 LIWPM 5 LIW – PM 6 LIW
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 4 LIW
Optional shaft at motor speed (lead end only) 10mm dia.�33mm long.Approx. weight: PM 2/4 LIW – 5.89 Kg
PM 5/6 LIW – 6.08 Kg
4 holes on 57.1mm P.C.D.Can be tapped M5�6mm deep.
4 holes tapped M8�12mm deep.
15mm dia. h6.Keyway 5mm�38mmlong.
Optional terminal box tapped 20mmconduit or PG 13.5 on request.Standard entry position R.H.S. Leads out here
30cm
Per
man
ent
Mag
net
Mot
or C L
PM 10 SIS
OUTPUT TORQUE (Nm)FINALR.P.M. RATIO
In Line Reduction Multi-Spur Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosure: – Totally Enclosed (IP 54)
Gearbox Type:
SISSpeed Range: 5 – 136 r.p.m.
PM 7 SIS
� Voltage, Construction, Connections, Motor PerformanceSpecifications and Optional Extras see pages 72 and 74 for full details.
(1 Nm = 8.85 lbs. ins.) (1 Nm = 10.2 cmkp)
GearboxSpecification
Motor Speed1500 r.p.m.
PM 7 SIS PM 8 SIS PM 9 SIS PM 10 SIS PM 11 SISCont
Motor Rating7.5 watts
Cont
Motor Rating12.5 watts
Cont
Motor Rating19 watts
Cont
Motor Rating20 watts
Cont
Motor Rating33 watts
1 Hour
Motor Rating10 watts
1 Hour
Motor Rating15 watts
1 Hour
Motor Rating24 watts
1 Hour
Motor Rating25 watts
1 Hour
Motor Rating40 watts
56.68.711.61621285268
3032281721299471532922
6.65.754
3.12.31.81.10.8
7.97.66.65.44.23.12.41.41.1
7.97.97.96.75.23.93.11.81.4
–––
7.96.24.63.72.21.7
–––
7.97.95.94.62.82.1
–--–
7.97.45.93.52.7
–––––
6.24.92.92.3
–––––
7.76.13.62.8
––––––
7.94.73.7
––––––
7.95.84.5
OUTPUT TORQUE (Nm)FINALR.P.M. RATIO
GearboxSpecification
Motor Speed2000 r.p.m.
PM 7 SIS PM 8 SIS PM 9 SIS PM 10 SIS PM 11 SISCont
Motor Rating10 watts
Cont
Motor Rating17 watts
Cont
Motor Rating25 watts
Cont
Motor Rating30 watts
Cont
Motor Rating45 watts
1 Hour
Motor Rating13 watts
1 Hour
Motor Rating21 watts
1 Hour
Motor Rating33 watts
1 Hour
Motor Rating40 watts
1 Hour
Motor Rating55 watts
6.69
11.615.52128386991
3032281721299471532922
6.65.754
3.12.31.81.10.8
7.97.46.55.343
2.41.41.1
7.97.97.97.15.44.13.21.91.5
–––
7.97.25.34.22.51.9
–––
7.97.85.84.62.72.1
––––
7.97.76.13.62.8
––––
7.97.45.43.22.5
–––––
7.97.34.33.4
–––––
7.97.95
3.9
––––––
7.96
4.7
OUTPUT TORQUE (Nm)FINALR.P.M. RATIO
GearboxSpecification
Motor Speed3000 r.p.m.
PM 7 SIS PM 8 SIS PM 9 SIS PM 10 SIS PM 11 SISCont
Motor Rating15 watts
Cont
Motor Rating25 watts
Cont
Motor Rating38 watts
Cont
Motor Rating45 watts
Cont
Motor Rating65 watts
1 Hour
Motor Rating20 watts
1 Hour
Motor Rating33 watts
1 Hour
Motor Rating45 watts
1 Hour
Motor Rating55 watts
1 Hour
Motor Rating80 watts
1013
17.423324257103136
3032281721299471532922
6.65.754
3.12.31.81.10.8
7.97.66.65.44.23.12.41.41.1
7.97.97.96.75.23.93.11.81.4
–––
7.96.95.14
2.41.9
–––
7.97.85.84.62.72.1
––––
7.97
5.53.32.5
––––
7.97
5.53.32.5
–––––
7.97.34.33.4
–––––
7.97.95
3.9
––––––
7.96
4.7
92
42.5
78
45
60
74
50
Ø 51
Ø 35
36
25.5 35.5 23
6.35
PM 7 SIS = 156PM 8 SIS = 169PM 9 SIS = 182
Ø 5
6
PM 7 SISPM 8 SISPM 9 SIS
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 8 SIS
Optional shaft at motor speed (lead end only) 7.93mm dia.�33mm long.
Approx. weight: PM 7 SIS – 1.40 KgPM 8 SIS – 1.60 KgPM 9 SIS – 1.80 Kg
93
Ø 6
6
35.5
78
45
60
74
50
Ø 51
Ø 35
36
25.5 35.5 23
6.35
PM 10 SIS = 179PM 11 SIS = 198
PM 10 SISPM 11 SIS
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 10 SIS
Optional shaft at motor speed (lead end only) 7.93mm dia.�33mm long.Approx. weight: PM 10 SIS – 2.04 Kg
PM 11 SIS – 2.50 Kg
Leads out here 30cm(flexible grommet).
10mm dia. h6.Flat 6mm wide�19mm long.
10mm dia. h6.Flat 6mm�19mm long.
Optional mounting flange(see below).
Optional mounting flange(see below).
4 holes tapped M4�9mm deep.
4 holes tapped M4�9mm deep.
4 holes on 41.27mm P.C.D.Can be tapped M5�8mm deep.
Leads out here 30cm
4 holes on 41.27mm P.C.D.Can be tapped M5�8mm deep.
4
18
1.8
9.5
Ø 35
Ø 88
Ø 75
S67 Optional Plastic Mounting Flange
4 equally spaced holes on 77.2mmP.C.D. cored 4.1mm dia.
SIS standardshaft extension
Dimensions in mm. Scale 1:4
Per
man
ent
Mag
net
In Line Reduction Multi Spur Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosure: – PM1, PM2 & PM6 – Drip Proof Internal Fan Cooled (IP 21)PM3, PM4 & PM5 – Totally Enclosed (IP 54)
Gearbox Type:
MISSpeed Range: 15 – 467 r.p.m
OUTPUT TORQUE (Nm)FINALR.P.M.
PM 3 MIS
� Voltage, Construction, Connections, Motor PerformanceSpecifications and Optional Extras see pages 72 and 74 for full details.
(1 Nm = 8.85 lbs. ins.) (1 Nm = 10.2 cmkp)
RATIO
PINION SPUR
GearboxSpecification
Motor Speed3000 r.p.m.
Cont
Motor Rating68 watts
Cont
Motor Rating90 watts
Cont
Motor Rating120 watts
Cont
Motor Rating150 watts
1 Hour
Motor Rating90 watts
1 Hour
Motor Rating120 watts
1 Hour
Motor Rating150 watts
30 MINS
Motor Rating200 watts
PM 3 MIS PM 4 MIS PM 5 MIS PM 6 MIS
30456986105162199246467
3.232.133.231.122.133.231.122.131.12
31.331.313.4531.313.455.7313.455.735.73
171176533
2.11.2
2215108644
2.81.6
2215108644
2.81.6
291913119654
2.1
291913119654
2.1
3624161311765
2.6
3624161311765
2.6
4532221814986
3.5
OUTPUT TORQUE (Nm)FINALR.P.M.
RATIO
PINION SPUR
GearboxSpecification
Motor Speed2000 r.p.m.
Cont
Motor Rating45 watts
Cont
Motor Rating60 watts
Cont
Motor Rating80 watts
Cont
Motor Rating100 watts
1 Hour
Motor Rating60 watts
1 Hour
Motor Rating80 watts
1 Hour
Motor Rating100 watts
30 MINS
Motor Rating150 watts
PM 3 MIS PM 4 MIS PM 5 MIS PM 6 MIS
2030465770108133164312
3.232.133.231.122.133.231.122.131.12
31.331.313.4531.313.455.7313.455.735.73
161176533
2.11.2
2215108644
3.01.6
2215108644
3.01.6
291913119654
2.1
291913119654
2.1
3624161311765
2.6
3624161311765
2.6
45362420161197
3.9
OUTPUT TORQUE (Nm)FINALR.P.M.
RATIO
PINION SPUR
GearboxSpecification
Motor Speed1500 r.p.m.
Cont
Motor Rating30 watts
Cont
Motor Rating40 watts
Cont
Motor Rating50 watts
Cont
Motor Rating60 watts
1 Hour
Motor Rating40 watts
1 Hour
Motor Rating50 watts
1 Hour
Motor Rating60 watts
30 MINS
Motor Rating80 watts
PM 3 MIS PM 4 MIS PM 5 MIS PM 6 MIS
152235435281100123234
3.232.133.231.122.133.231.122.131.12
31.331.313.4531.313.455.7313.455.735.73
151065432
1.81.0
191397643
2.51.4
191397643
2.51.4
24161197543
1.6
24161197543
1.6
291913119654
2.1
291913119654
2.1
3926171412865
2.8
94
95
PM 3 MIS = 231PM 1/4 MIS = 243.5PM 2/5 MIS = 256PM 6 MIS = 269
Ø 77
40.6
15°
96.8
28.5
27.6
7
7.5
51
Ø 3
4
40
Ø 60
= 95 =
= 112 =60
45
123
71
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 1/4 MIS
Optional shaft at motor speed (lead end only) 10mm dia.�33mm long.
Approx. weight: PM 1/3 MIS – 4.13 KgPM 2/4 MIS – 4.48 KgPM 5/6 MIS – 4.67 Kg
Leads out here 30cm
4 holes tapped M8�15mm deep.
4 holes on 48mm P.C.D.Can be tapped M5�11mm deep.
Optional terminal box tapped 20mmconduit or PG 13.5 on request.Standard entry position R.H.S.
14mm dia. h6.Keyway 5mm�38mm long.
PM 1 MIS – PM 2 MISPM 3 MIS – PM 4 MISPM 5 MIS – PM 6 MIS
Per
man
ent
Mag
net
Mot
or C L
OUTPUT TORQUE (Nm)FINALR.P.M.
RATIO
PINION SPUR
In Line Reduction Multi-Spur Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosures: – PM 1 – PM 2 – PM 6 – Drip Proof Internal Fan Cooled (IP 21)PM 10 – PM 11 – PM 3 – PM 4 – PM 5 – Totally Enclosed (IP 54)
Gearbox Type:
LISSpeed Range: 4 – 500 r.p.m.
� Voltage, Construction, Connections, Motor PerformanceSpecifications and Optional Extras see pages 72 and 74 for full details.On request gearbox available without feet, can be mounted off of gearbox spigot tapping.
(1 Nm = 8.85 lbs. ins.) (1 Nm = 10.2 cmkp)
GearboxSpecification
Motor Speed1500 r.p.m.
Cont 1 Hour
Motor MotorRating Rating20 watts 25 watts
Cont 1 Hour
Motor MotorRating Rating33 watts 40 watts
Cont
Motor Rating40 watts
1 Hour
Motor Rating40 watts
Cont
Motor Rating50 watts
1 Hour
Motor Rating50 watts
Cont
Motor Rating60 watts
1 Hour
Motor Rating60 watts
PM 10 LIS PM 11 LIS PM 1 LIS PM 3 LIS PM 2 LIS PM 4 LIS PM 6 LIS PM 5 LIS
479132027306083125250
3:12:13:11:13:11:12:11:13:12:11:1
115:1115:156:1115:125:156:125:125:16:16:16:1
332216117
5.552211
5436261812984321
654432221511105431
654432221511105431
654432221511105431
745540271813126532
745540271813126532
7465483322
16.5157642
7465483322
16.5157642
412720149763221
FINALR.P.M. OUTPUT TORQUE (Nm)
RATIO
PINION SPUR
GearboxSpecification
Motor Speed2000 r.p.m.
Cont 1 Hour
Motor MotorRating Rating30 watts 40 watts
Cont 1 Hour
Motor MotorRating Rating45 watts 55 watts
Cont
Motor Rating60 watts
1 Hour
Motor Rating60 watts
Cont
Motor Rating80 watts
1 Hour
Motor Rating80 watts
Cont
Motor Rating100 watts
1 Hour
Motor Rating100 watts
PM 10 LIS PM 11 LIS PM 1 LIS PM 3 LIS PM 2 LIS PM 4 LIS PM 6 LIS PM 5 LIS
69121727354080111167333
3:12:13:11:13:11:12:11:13:12:11:1
115:1115:156:1115:125:156:125:125:16:16:16:1
372517128653211
5537251812984321
674531221511105431
744934251612115431
744934251612115431
746545332216157642
746545332216157642
747456412720189752
747456412720189752
4933221611874321
FINALR.P.M. OUTPUT TORQUE (Nm)
RATIO
PINION SPUR
GearboxSpecification
Motor Speed3000 r.p.m.
Cont 1 Hour
Motor MotorRating Rating45 watts 55 watts
Cont 1 Hour
Motor MotorRating Rating65 watts 80 watts
Cont
Motor Rating90 watts
1 Hour
Motor Rating90 watts
Cont
Motor Rating120 watts
1 Hour
Motor Rating120 watts
Cont
Motor Rating150 watts
1 Hour
Motor Rating150 watts
PM 10 LIS PM 11 LIS PM 1 LIS PM 3 LIS PM 2 LIS PM 4 LIS PM 6 LIS PM 5 LIS
9131826405360120167250500
3:12:13:11:13:11:12:11:13:12:11:1
115:1115:156:1115:125:156:125:125:16:16:16:1
372517128653211
53352418128.584321
6544302215
10.5105431
744934251612115431
744934251612115431
746545332216157642
746545332216157642
747456412720189752
747456412720189752
45302015107.573321
PM 3 LISPM 10 LIS
96
Ø 66
35.5
PM 10 LIS = 215PM 11 LIS = 234
6 44.75
5651
Ø 4
7.6
Ø 125
48.7
88.1
103.2
123
134
68.2
5
9.5
SLOT19 x 7.1
120
85.7
PM 10 LISPM 11 LIS
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 10 LIS
Optional shaft at motor speed (lead end only) 7.93mm dia.�33mm long.Approx. weight: PM 10 LIS – 4.77 Kg
PM 11 LIS – 5.23 Kg
4 holes on 70mm P.C.D.Can be tapped M5�11mm deep.
Motor CL
97
PM 3 LIS = 245PM 1/4 LIS = 257PM 2/5 LIS = 270PM 6 LIS = 283
Ø 77
40.6
15°6 44.75
5651
Ø 4
7.6
Ø 125
48.7
88.1
103.2
123
134
68.2
5
9.5
SLOT19 x 7.1
120
85.7
71
PM 1 LIS – PM 2 LIS – PM 3 LISPM 4 LIS – PM 5 LIS – PM 6 LIS
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 1/4 LIS
Optional shaft at motor speed (lead end only) 10mm dia.�33mm long.
Approx. weight: PM 1/3 LIS – 5.76 KgPM 2/4 LIS – 6.11 KgPM 5/6 LIS – 6.30 Kg
Leads out here 30cm
15mm dia. h6.Keyway 5mm�38mm long.
15mm dia. h6.Keyway 5mm�38mm long.
Alternative shaftposition on request.
Alternative shaftposition on request.
Leads out here 30cm
Optional terminal box tapped 20mmconduit or PG 13.5 on request.Shown standard entry position R.H.S.
4 holes on 70mm P.C.D.Can be tapped M5�11mm deep.
Motor CL
Per
man
ent
Mag
net
(1 Nm = 8.85 lbs. ins.) (1 Nm = 10.2 cmkp)
OUTPUT TORQUE (Nm)FINALR.P.M.
RATIO
PINION SPUR
GearboxSpecification
Motor Speed1500 r.p.m.
ContMotor Rating
65 watts
15 MinMotor Rating
120 watts
1 Hour Motor Rating
110 watts
1 Hour Motor Rating
85 watts
ContMotor Rating
85 watts
15 MinMotor Rating
155 watts
PM 50 LIS PM 60 LIS
479132027306083125250
3:12:13:11:13:11:12:11:13:12:11:1
115:1115:156:1115:125:156:125:125:16:16:16:1
747156352419168642
-74744631252110853
--
10065443529151184
7474744631252110853
--
9560403227131073
--
100745645371915105
PM 50 LIS
� Voltage, Construction, Connections, Motor Performance Specifications andOptional Extras see pages 72 and 74 for full details.On request gearbox available without feet, can be mounted off of gearbox spigot tapping.
In Line Reduction Multi-Spur Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosures: – PM50 LIS – Totally Enclosed (IP 54)PM60 LIS – Drip Proof Internal Fan Cooled (IP 21)
Gearbox Type:
LISSpeed Range: 4-500 r.p.m.
OUTPUT TORQUE (Nm)FINALR.P.M.
RATIO
PINION SPUR
GearboxSpecification
Motor Speed2000 r.p.m.
ContMotor Rating
105 watts
15 MinMotor Rating
185 watts
1 Hour Motor Rating
170 watts
1 Hour Motor Rating
135 watts
ContMotor Rating
140 watts
15 MinMotor Rating
230 watts
PM 50 LIS PM 60 LIS
6912172735 4080111167333
3:12:13:11:13:11:12:11:13:12:11:1
115:1115:156:1115:125:156:125:125:16:16:16:1
7474684329231910752
--
885537292412963
--
10074504034171394
74749157383025131073
--
10069463731151284
---
746350422116115
98
PM 50 LIS = 288PM 60 LIS = 300
Ø 77
40.6
15°6 44.75
5651
Ø 4
7.6
Ø 125
48.7
88.1
103.2
12313
4
68.2
5
9.5
SLOT19 x 7.1
120
85.7
71
PM 50 LISPM 60 LIS
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 50 LIS
Optional shaft at motor speed (lead end only) 10mm dia.�33mm long. Approx. weight: PM 50/60 LIS 6.55 Kg
99
15mm dia. h6.Keyway 5mm�38mm long.
Alternative shaftposition on request.
Leads out here 30cm
Optional terminal box tapped20mm conduit PG 13.5 on request.Standard entry position R.H.S.
4 holes on 70mm P.C.D. Can betapped M5�11mm deep.
OUTPUT TORQUE (Nm)FINALR.P.M.
RATIO
PINION SPUR
GearboxSpecification
Motor Speed3000 r.p.m.
ContMotor Rating
155 watts
15 MinMotor Rating
280 watts
1 Hour Motor Rating
255 watts
1 Hour Motor Rating
200 watts
ContMotor Rating
210 watts
15 MinMotor Rating
345 watts
PM 50 LIS PM 60 LIS
9131826405360120167250500
3:12:13:11:13:11:12:11:13:12:11:1
115:1115:156:1115:125:156:125:125:16:16:16:1
747467422822199752
--
875536292412963
--
10074514034171394
74749157383025131073
--
10069463731151284
---
746350422116115
In Line Reduction Multi-Spur Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosures: – PM50 LIS – Totally Enclosed (IP 54)PM60 LIS – Drip Proof Internal Fan Cooled (IP 21)
Geabox Type:
LISSpeed Range: 4-500 r.p.m.
Motor CL
Per
man
ent
Mag
net
OUTPUT TORQUE (Nm)FINALR.P.M.
Worm and Multi-Spur Reduction Gear UnitVariable Speed – D.C. Permanent Magnet
Enclosure: – Totally Enclosed (IP 54)
Gearbox Type:
SWSSpeed Range: 1.1 – 76 r.p.m.
PM 8 SWS
� Voltage, Construction, Connections, Motor PerformanceSpecifications and Optional Extras see pages 72 and 74 for full details.
GEARBOX RATIO
WORM SPUR
(1 Nm = 8.85 lbs. ins.) (1 Nm = 10.2 cmkp)
GearboxSpecification
Motor Speed1500 r.p.m.
PM 7 SWS PM 8 SWS PM 9 SWS PM 10 SWSCont
Motor Rating7.5 watts
1 Hour
Motor Rating10 watts
Cont
Motor Rating12.5 watts
Cont
Motor Rating19 watts
Cont
Motor Rating20 watts
1 Hour
Motor Rating15 watts
1 Hour
Motor Rating24 watts
1 Hour
Motor Rating25 watts
1.12.13.85.2710
12.517253038
44:122 1/2:112 1/2:19 1/3:19 1/3:16 1/4:112 1/2:19 1/3:16 1/4:151/6:14 1/8:1
31.3:131.3:131.3:131.3:123.5:123.5:19.6:19.6:19.6:19.6:19.6:1
1111117.564
3.53222
1111119
7.564
3.53
2.52
---
119
7.554
3.533
---
119
8.5654
3.43
-----
1198654
-----
1111107
5.85
------
108654
------
11107
5.85
OUTPUT TORQUE (Nm)FINALR.P.M.
GEARBOX RATIO
WORM SPUR
GearboxSpecification
Motor Speed2000 r.p.m.
PM 7 SWS PM 8 SWS PM 9 SWS PM 10 SWSCont
Motor Rating10 watts
1 Hour
Motor Rating13 watts
Cont
Motor Rating17 watts
Cont
Motor Rating25 watts
Cont
Motor Rating30 watts
1 Hour
Motor Rating21 watts
1 Hour
Motor Rating33 watts
1 Hour
Motor Rating40 watts
1.52.85.27
9.313.61722334050
44:122 1/2:112 1/2:19 1/3:19 1/3:16 1/4:112 1/2:19 1/3:16 1/4:15 1/6:14 1/8:1
31.3:131.3:131.3:131.3:123.5:123.5:19.6:19.6:19.6:19.6:19.6:1
1111117.564
3.53222
1111119
7.564
3.53
2.52
---
119
7.554
3.533
---
119
8.57.565
4.24
-----
1197654
-----
111110765
------
119765
-------
119
7.56
OUTPUT TORQUE (Nm)FINALR.P.M.
GEARBOX RATIO
WORM SPUR
GearboxSpecification
Motor Speed3000 r.p.m.
PM 7 SWS PM 8 SWS PM 9 SWS PM 10 SWSCont
Motor Rating15 watts
1 Hour
Motor Rating20 watts
Cont
Motor Rating25 watts
Cont
Motor Rating38 watts
Cont
Motor Rating45 watts
1 Hour
Motor Rating33 watts
1 Hour
Motor Rating45 watts
1 Hour
Motor Rating55 watts
2.24.37.710.314
20.525
33.5506076
44:122 1/2:112 1/2:19 1/3:19 1/3:16 1/4:112 1/2:19 1/3:16 1/4:15 1/6:14 1/8:1
31.3:131.3:131.3:131.3:123.5:123.5:19.6:19.6:19.6:19.6:19.6:1
1111117.564
3.53222
1111119
7.564
3.53
2.52
---
119
7.554
3.533
---
119
8.57.565
4.24
-----
1197654
-----
111110765
------
119765
-------
119
7.56
PM 10 SWS
100
101
65PM 7 SWS = 184
Ø 5
6
42.5
25.4
Ø 2
9
Ø 2
6
32
33.5
6.6
1342
11 47
11 30
68
99.5
43.236.8
80
80
92
PM 9 SWS = 210PM 8 SWS = 197
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 8 SWS
Optional shaft at motor speed (lead end only) 7.93mm dia.�33mm long.
Approx. weight: PM 7 SWS – 1.35 KgPM 8 SWS – 1.55 KgPM 9 SWS – 1.75 Kg
Ø 6
6
35.5
25.4
Ø 2
9
Ø 2
6
32
33.5
6.6
1342
11 47
11 30
68
43.236.8
80
80
92
199
103.
5
PM 10 SWSDimensions in mm. Scale 1:4
Optional shaft at motor speed (lead end only) 7.93mm dia.�33mm long. Approx. weight: PM 10 SWS – 1.97 Kg
Leads out here 30cm(flexible grommet).
Leads out here 30cm
4 holes tappedM5�10mm deep.
4 holes tappedM5�10mm deep.
10mm dia. h6. with6mm flat�25.4mm long.Available both sides.
10mm dia. h6.with 6mmflat�25.4mm long.Available both sides.
PM 7 SWSPM 8 SWSPM 9 SWS
Per
man
ent
Mag
net
Mot
or C L
Mot
or C L
Worm and Multi-Spur Reduction Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosure: – Totally enclosed (IP 54)
Gearbox Type:
MWSSpeed Range: 1.1 – 150 r.p.m.
OUTPUT TORQUE (Nm)FINALR.P.M.
PM 8 MWS
� Voltage, Construction, Connections,Motor Performance Specifications andOptional Extras see pages 72 and 74 forfull details.
(1 Nm = 8.85 lbs. ins.) (1 Nm = 10.2 cmkp)
GEARBOX RATIO
WORM SPUR
GearboxSpecification
Motor Speed1500 r.p.m.
Cont
Motor Rating7.5 watts
Cont
Motor Rating12.5 watts
Cont
Motor Rating19 watts
Cont
Motor Rating20 watts
Cont
Motor Rating33 watts
1 Hour
Motor Rating10 watts
1 Hour
Motor Rating15 watts
1 Hour
Motor Rating24 watts
1 Hour
Motor Rating25 watts
1 Hour
Motor Rating40 watts
PM 7 MWS PM 8 MWS PM 9 MWS PM 10 MWS PM 11 MWS
1.11.62356810121416242832374556
40:127:1
18 1/2:112 1/2:19 1/3:17 1/4:15 1/6:14 1/8:18 1/3:17 1/4:16 1/4:14 1/8:18 1/2:17 1/4:16 1/4:15 1/6:14 1/8:1
35.39:135.39:135.39:135.39:135.39:135.39:135.39:135.39:115.1:115.1:115.1:115.1:16.5:16.5:16.5:16.5:16.5:1
19.815
11.79
7.26
4.63.82.82.62.31.61.31.21.00.90.7
26.420
15.6129.68
6.15
3.83.43
2.11.71.61.41.21.0
33.125
19.514.912107.66.34.74.33.82.72.21.91.71.51.2
4545252017131087654
3.22.92.62.21.8
39.729.823.417.914.4129.17.55.75.14.63.22.62.32.11.81.5
--
37.528.723
19.214.6129.18.27.35.14.13.73.32.82.3
--
21.323.919.216
12.110.07.66.86.14.33.53.12.82.41.9
---
29.82420
15.212.59.58.57.65.34.33.93.53.02.4
---
39.431.726.420
16.512.511.310.17.15.75.14.63.93.2
----
38.432
24.320
15.213.712.29.66.96.25.54.73.9
OUTPUT TORQUE (Nm)FINALR.P.M.
GEARBOX RATIO
WORM SPUR
GearboxSpecification
Motor Speed2000 r.p.m.
Cont
Motor Rating10 watts
Cont
Motor Rating17 watts
Cont
Motor Rating25 watts
Cont
Motor Rating30 watts
Cont
Motor Rating45 watts
1 Hour
Motor Rating13 watts
1 Hour
Motor Rating21 watts
1 Hour
Motor Rating33 watts
1 Hour
Motor Rating40 watts
1 Hour
Motor Rating55 watts
PM 7 MWS PM 8 MWS PM 9 MWS PM 10 MWS PM 11 MWS
1.42.135681114161821323743496075
40:127:1
18 1/2:112 1/2:19 1/3:17 1/4:15 1/6:14 1/8:18 1/3:17 1/4:16 1/4:14 1/8:18 1/3:17 1/4:16 1/4:15 1/6:14 1/8:1
35.39:135.39:135.39:135.39:135.39:135.39:135.39:135.39:115.1:115.1:115.1:115.1:16.5:16.5:16.5:16.5:16.5:1
19.814.911.7
97.26
4.63.82.82.62.31.61.31.21.00.90.7
25.819.315.211.69.47.85.94.93.73.33
2.11.71.51.31.20.9
33.725.319.915.212.210.27.76.44.84.43.92.72.22.01.81.51.2
41.731.224.618.815.112.69.67.96
5.44.83.42.72.42.21.91.5
4537.229.323.41815
11.49.47.16.45.74.03.22.92.62.21.8
--
38.729.523.819.815
12.49.48.57.55.24.22.82.42.92.4
--
35.226.421.618
13.711.38.57.76.94.83.93.53.12.72.2
---
35.828.824
18.215.011.410.39.16.45.24.74.22.52.9
---
40.332.427
20.516.912.811.510.37.25.85.24.74.03.2
----
39.633.025.120.615.714.112.68.87.16.45.74.94.0
PM 10 MWS
102
OUTPUT TORQUE (Nm)FINALR.P.M.
GEARBOX RATIO
WORM SPUR
GearboxSpecification
Motor Speed3000 r.p.m.
Cont
Motor Rating15 watts
Cont
Motor Rating25 watts
Cont
Motor Rating38 watts
Cont
Motor Rating45 watts
Cont
Motor Rating65 watts
1 Hour
Motor Rating20 watts
1 Hour
Motor Rating33 watts
1 Hour
Motor Rating45 watts
1 Hour
Motor Rating55 watts
1 Hour
Motor Rating80 watts
PM 7 MWS PM 8 MWS PM 9 MWS PM 10 MWS PM 11 MWS
2.13.24.66.891217212428324856647490112
40:127:1
18 1/2:112 1/2:19 1/3:17 1/4:15 1/6:14 1/8:18 1/3:17 1/4:16 1/4:14 1/8:18 1/3:17 1/4:16 1/4:15 1/6:14 1/8:1
35.39:135.39:135.39:135.39:135.39:135.39:135.39:135.39:115.1:115.1:115.1:115.1:16.5:16.5:16.5:16.5:16.5:1
19.814.911.7
97.26
4.63.82.82.62.31.61.31.21.00.90.7
26.419.815.611.99.68
6.15
3.83.43
2.11.71.61.41.21.0
33.124.819.514.912107.66.34.74.33.82.72.21.91.71.51.2
43.632.725.819.715.813.2108.26.35.65
3.52.82.62
1.91.6
4537.729.722.718.215.211.59.57.26.55.84.13.33.02.62.21.8
--
35.226.921.618
13.711.38.57.76.94.83.93.53.12.72.2
--
35.226.921.618
13.711.38.57.76.94.83.93.53.12.72.2
---
32.526.422
16.713.810.49.48.65.94.74.33.83.22.7
---
38.831.226
19.716.312.311.19.97.05.65.14.33.83.2
----
38.432.024.320.015.213.712.28.66.96.25.54.73.9
Worm and Multi-Spur Reduction Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosure: – Totally enclosed (IP 54)
Gearbox Type:
MWSSpeed Range: 1.1 – 150 r.p.m.
OUTPUT TORQUE (Nm)FINALR.P.M.
GEARBOX RATIO
WORM SPUR
GearboxSpecification
Motor Speed4000 r.p.m.
Cont
Motor Rating20 watts
Cont
Motor Rating33 watts
Cont
Motor Rating50 watts
Cont
Motor Rating60 watts
Cont
Motor Rating90 watts
1 Hour
Motor Rating25 watts
1 Hour
Motor Rating40 watts
1 Hour
Motor Rating60 watts
1 Hour
Motor Rating75 watts
1 Hour
Motor Rating110 watts
PM 7 MWS PM 8 MWS PM 9 MWS PM 10 MWS PM 11 MWS
2.94.2691216222832374264748599120150
40:127:1
18 1/2:112 1/2:19 1/3:17 1/4:15 1/6:14 1/8:18 1/3:17 1/4:16 1/4:14 1/8:18 1/3:17 1/4:16 1/4:15 1/6:14 1/8:1
35.39:135.39:135.39:135.39:135.39:135.39:135.39:135.39:115.1:115.1:115.1:115.1:16.5:16.5:16.5:16.5:16.5:1
19.814.911.7
97.26
4.63.82.82.62.31.61.31.21.00.90.7
24.818.614.711.2
97.55.74.73.63.22.92.01.61.51.31.10.9
29.622.217.513.410.78.96.85.64.33.83.42.41.91.71.51.21.1
39.729.823.417.914.412.09.17.55.75.14.63.22.62.22.11.81.5
4537.229.322.418.015
11.49.47.16.45.74.03.22.92.62.21.8
--
35.226.921.618
13.711.38.57.76.94.83.93.53.12.72.2
--
35.226.921.618
13.711.38.57.66.94.83.93.53.12.72.0
---
33.627
22.517.114.110.79.68.65.04.94.43.93.32.7
---
40.332.427
20.516.922.811.510.37.25.85.24.74
3.3
----
39.533
25.120.615.714.112.68.87.76.45.74.94.0
103
Ø 6
6
PM 10 MWS = 217PM 11 MWS = 236
35.5
751
Ø 3
4
40
95.3
20.262.3
Ø 60
= 95 =
112
3.4
60
45
107
131
PM 10 MWSPM 11 MWS
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 10 MWS
Ø 5
6
PM 7 MWS = 202PM 8 MWS = 215PM 9 MWS = 228
42.5
751
Ø 3
4
40
95.3
20.262.3
Ø 60
= 95 =
112
3.4
60
45
107 12
8
PM 7 MWSPM 8 MWSPM 9 MWS
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 8 MWS
Optional shaft at motor speed (lead end only) 7.93mm dia.�33mm long.
Optional shaft at motor speed (lead end only) 7.93mm dia.�33mm long.
Approx. weight: PM 7 MWS – 3.25 KgPM 8 MWS – 3.45 KgPM 9 MWS – 3.65 Kg
Approx. weight: PM 10 MWS – 3.87 KgPM 11 MWS – 4.33 Kg
Leads out here 30cm
Leads out here 30cm(flexible grommet).
Optional (either side): 4 holeson 48mm P.C.D. Can betapped M5�11mm deep.
Optional (either side): 4 holeson 48mm P.C.D. Can betapped M5�11mm deep.
14mm dia. h6. Keyway 5mm�38mm long.Available both sides.
14mm dia. h6. Keyway 5mm�38mm long.Available both sides.
4 holes tappedM8�15mm deep.
4 holes tappedM8�15mm deep.
Per
man
ent
Mag
net
Motor CL
Motor CL
Mot
or C L
Mot
or C L
OUTPUT TORQUE (Nm)FINALR.P.M.
OUTPUT TORQUE (Nm)FINALR.P.M.
RATIO
WORM SPUR
Worm and Multi-Spur Reduction Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosures: – PM 1 – PM 2 – PM 6 – Drip Proof Internal Fan Cooled (IP 21)PM 10 – PM 11 – PM 3 – PM 4 – PM 5 – Totally Enclosed (IP 54)
Gearbox Type:
LWSSpeed Range: 0.45 – 80 r.p.m.
(1 Nm = 8.85 lbs. ins.) (1 Nm = 10.2 cmkp)
GearboxSpecification
Motor Speed1500 r.p.m.
ContMotor Rating
33 watts
ContMotor Rating
40 watts
1 HourMotor Rating
40 watts
ContMotor Rating
50 watts
1 HourMotor Rating
50 watts
ContMotor Rating
60 watts
1 HourMotor Rating
60 watts
PM 11 LWS PM 1 LWS PM 3 LWS PM 2 LWS PM 4 LWS PM 6 LWS PM 5 LWS
0.450.81.51.82.22.62.93.23.74.34.56.5
30:116 1/2:18 1/3:17 1/4:112 1/2:110 1/3:19 1/3:18 1/3:17 1/4:16 1/4:113 1/2:19 1/3:1
115:1115:1115:1115:156:156:156:156:156:156:125:125:1
1001001001008270635953483928
10010010010010084767264584734
10010010010010084767264584734
100100100100100100959080735942
100100100100100100959080735942
10010010010010010010010096876251
10010010010010010010010096876251
OUTPUT TORQUE (Nm)FINALR.P.M.
RATIO
WORM SPUR
GearboxSpecification
Motor Speed2000 r.p.m.
Cont 1 HourMotor Motor Rating Rating30 watts 40 watts
Cont 1 HourMotor Motor Rating Rating45 watts 55 watts
Cont 1 HourMotor Motor Rating Rating45 watts 60 watts
Cont 1 HourMotor Motor Rating Rating60 watts 90 watts
Cont 1 HourMotor Motor Rating Rating60 watts 80 watts
Cont 1 HourMotor Motor Rating Rating80 watts 120 watts
Cont 1 HourMotor Motor Rating Rating80 watts 100 watts
Cont 1 HourMotor Motor Rating Rating
100 watts 150 watts
PM 10 LWS PM 11 LWS PM 3 LWS PM 1 LWS PM 4 LWS PM 2 LWS PM 5 LWS PM 6 LWS
0.612
2.42.83.53.84.34.95.76
6.57.78.59.5132025303540
30:116 1/2:18 1/3:17 1/4:112 1/2:110 1/3:19 1/3:18 1/3:17 1/4:16 1/4:113 1/2:112 1/2:110 1/3:19 1/3:18 1/3:16 1/4:116 1/2:113 1/2:111 1/3:19 1/3:18 1/3:1
115:1115:1115:1115:156:156:156:156:156:156:125:125:125:125:125:125:16:16:16:16:16:1
100100786956474340363326252119181476544
1001001009275635753484435332825241998766
100100100100847164605449403732282722119876
100100100100100877874665949464035332713121088
100100100100847164605449403732282722119876
100100100100100958680726553504238362915131198
100100100100100958680726553504238362915131198
100100100100100100100100100988074645654442218161412
100100100100100958680726553504238362915131198
10010010010010010010010096876262
56.55148392017151211
10010010010010010010010096876262
56.55148392017151211
100100100100100100100100100100100100847672583026221816
10010010010010010010010096876262
56.55148392017151211
1001001001001001001001001001006262626260482421181514
1001001001001001001001001001006262626260482421181514
10010010010010010010010010010093939393907236
31.527
22.521
RATIO
WORM SPUR
GearboxSpecification
Motor Speed3000 r.p.m.
Cont 1 HourMotor Motor Rating Rating45 watts 55 watts
Cont 1 HourMotor Motor Rating Rating65 watts 80 watts
1 HourMotor Rating
90 watts
ContMotor Rating
90 watts
1 HourMotor Rating
120 watts
ContMotor Rating
120 watts
1 HourMotor Rating
150 watts
ContMotor Rating
150 watts
PM 10 LWS PM 11 LWS PM 3 LWS PM 1 LWS PM 4 LWS PM 2 LWS PM 5 LWS PM 6 LWS
0.91.73
3.64.35.25.86.57.48.58.99.611.613
14.419303744
53.560
30:115 1/2:18 1/3:17 1/4:112 1/2:110 1/3:19 1/3:18 1/3:17 1/4:16 1/4:113 1/2:112 1/2:110 1/3:19 1/3:18 1/3:16 1/4:116 1/2:113 1/2:111 1/3:19 1/3:18 1/3:1
115:1115:1115:1115:156:156:156:156:156:156:125:125:125:125:125:125:16:16:16:16:16:1
100100786956474340363326252119181476544
100100978670595350454133312624221898765
100100100100847164605649403732282722119876
100100100100100847672645847443834322613121088
100100100100100958680726553504238362915131198
100100100100100958680726553504238362915131198
10010010010010010010010096876262
56.55148392017151211
10010010010010010010010096876262
56.55148392017151211
1001001001001001001001001001006262626260482421181514
1001001001001001001001001001006262626260482421181514
PM 5 LWSPM 10 LWS
� Voltage, Construction, Connections, Motor PerformanceSpecifications and Optional Extras see pages 72 and 74 forfull details.On request gearbox available without feet, unit can be mountedoff of gearbox spigot tapping.
Note: 17mm diameter shaft available with gear ratio’s 115:1, 56:1.
104
Worm and Multi-Spur Reduction Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosures: – PM 1 – PM 2 – PM 6 – Drip Proof Internal Fan Cooled (IP 21)PM 10 – PM 11 – PM 3 – PM 4 – PM 5 – Totally Enclosed (IP 54)
Gearbox Type:
LWSSpeed Range: 0.45 – 80 r.p.m.
105
OUTPUT TORQUE (Nm)FINALR.P.M.
RATIO
WORM SPUR
GearboxSpecification
Motor Speed4000 r.p.m.
Cont 1 HourMotor MotorRating Rating
60 w 75 w
Cont 1 HourMotor MotorRating Rating
90 w 110 w
ContMotor Rating120 w
1 HourMotor Rating120 w
ContMotor Rating160 w
1 HourMotor Rating160 w
ContMotor Rating200 w
1 HourMotor Rating200 w
PM 10 LWS PM 11 LWS PM 1 LWS PM 3 LWS PM 2 LWS PM 4 LWS PM 6 LWS PM 5 LWS
1.224
4.85.77
7.68.69.811.41213
15.51719
25.54049607080
30:116 1/2:18 1/3:17 1/4:112 1/2:110 1/3:19 1/3:18 1/3:17 1/4:16 1/4:113 1/2:112 1/2:110 1/3:19 1/3:18 1/3:16 1/4:116 1/2:113 1/2:111 1/3:19 1/3:18 1/3:1
115:1115:1115:1115:156:156:156:156:156:156:125:125:125:125:125:125:16:16:16:16:16:1
100100786956474340363326252119181476544
100100978670595350454133312624221898765
100100100100847164605449403732282722119876
100100100100100877874665949464035332713121088
100100100100100958580726553504238362915131198
100100100100100958580726553504238362915131199
10010010010010010010010096876262565148392017141211
10010010010010010010010096876262565148392017141211
1001001001001001001001001001006262626260482421181514
1001001001001001001001001001006262626260482421181514
Ø 6
6
35.5
PM 10 LWS = 236
565651
226 44.75
Ø 4
7.6Ø 125
PM 11 LWS = 255
123
103.2
19 x 7.1SLOT
85.7
120
9.5
68.2
5
134
88.1
48.4
PM 10 LWSPM 11 LWS
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 10 LWS
Optional shaft at motor speed (lead end only) 7.93mm dia.�33mm long.Approx. weight: PM 10 LWS – 5.03 Kg
PM 11 LWS – 5.49 Kg
15mm dia. h6.Keyway 5mm�38mm long. Motor CL
4 holes on 70mm P.C.D.Can be tapped M5�11mm deep.
Alternative shaft positionon request.
Ø 7
7
PM 3 LWS = 266PM 1/4 LWS = 278PM 2/5 LWS = 291PM 6 LWS = 304
40.6
15°
565651
226 44.75
Ø 4
7.6Ø 125
123
103.219 x 7.1SLOT
85.7
120
9.5
68.2
5
134
88.1
48.4
71
PM 1 LWS – PM 2 LWS – PM 3 LWSPM 4 LWS – PM 5 LWS – PM 6 LWS
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 1/4 LWS
Optional shaft at motor speed (lead end only) 10mm dia.�33mm long.
Approx. weight: PM 1/3 LWS – 6.02 KgPM 2/4 LWS – 6.37 KgPM 5/6 LWS – 6.56 Kg
15mm dia. h6.Keyway 5mm�38mm long.
4 holes on 70mm P.C.D.Can be tapped M5�11mm deep.
Alternative shaft positionon request.
Leads out here 30cm
Leads out here 30cm
Optional terminal box tapped 20mmconduit PG 13.5 on request.Standard position entry R.H.S.
Motor CL
Per
man
ent
Mag
net
Worm and Multi-Spur Reduction Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosures: – PM50 – Totally Enclosed (IP 54)PM60 – Drip Proof Internal Fan Cooled (IP 21)
Gearbox Type:
LWSSpeed Range: 0.45 – 80 r.p.m.
PM 50 LWS
� Voltage, Construction, Connections, Motor PerformanceSpecifications and Optional Extrassee pages 72 and 74 for full details.On request gearbox available without feet, unit can be mountedoff of gearbox spigot tapping.Note: 17mm diameter shaft available with gear ratio’s115:1, 56:1.
(1 Nm = 8.85 lbs. ins.) (1 Nm = 10.2 cmkp)
FINALR.P.M. OUTPUT TORQUE (Nm)
WORM
RATIO
SPUR
GearboxSpecification
Motor Speed1500 r.p.m.
ContMotorRating
65 watts
1 HourMotorRating
85 watts
ContMotorRating
85 watts
1 HourMotorRating
110 watts
PM 50 LWS PM 60 LWS
0.450.81.51.82.22.62.93.23.74.34.54.85.86.57.29.515.118.522
26.830
30:116 1/2:18 1/3:17 1/4:112 1/2:110 1/3:19 1/3:18 1/3:17 1/4:16 1/4:113 1/2:112 1/2:110 1/3:19 1/3:18 1/3:16 1/4:116 1/2:113 1/2:111 1/3:19 1/3:18 1/3:1
115:1115:1115:1115:156:156:156:156:156:156:125:125:125:125:125:125:16:16:16:16:16:1
100100100100100100100100100936262605451412118161312
1001001001001001001001001001006262626262542724201716
1001001001001001001001001001006262626262542724201716
1001001001001001001001001001006262626262623531262120
FINALR.P.M. OUTPUT TORQUE (Nm)
WORM
RATIO
SPUR
GearboxSpecification
Motor Speed2000 r.p.m.
ContMotorRating
105 watts
1 HourMotorRating
135 watts
ContMotorRating
140 watts
1 HourMotorRating
170 watts
PM 50 LWS PM 60 LWS
0.612
2.42.83.53.84.34.95.76
6.57.88.59.51320
24.7303540
30:116 1/2:18 1/3:17 1/4:112 1/2:110 1/3:19 1/3:18 1/3:17 1/4:16 1/4:113 1/2:112 1/2:110 1/3:19 1/3:18 1/3:16 1/4:116 1/2:113 1/2:111 1/3:19 1/3:18 1/3:1
115:1115:1115:1115:156:156:156:156:156:156:125:125:125:125:125:125:16:16:16:16:16:1
1001001001001001001001001001006262626262502522191614
1001001001001001001001001001006262626262623328242019
1001001001001001001001001001006262626262623429252220
1001001001001001001001001001006262626262624135312623
FINALR.P.M. OUTPUT TORQUE (Nm)
WORM
RATIO
SPUR
GearboxSpecification
Motor Speed3000 r.p.m.
ContMotorRating
155 watts
1 HourMotorRating
200 watts
ContMotorRating
210 watts
1 HourMotorRating
255 watts
PM 50 LWS PM 60 LWS
0.91.73
3.64.35.25.86.57.48.58.99.611.613
14.419303744
53.560
30:115 1/2:18 1/3:17 1/4:112 1/2:110 1/3:19 1/3:18 1/3:17 1/4:16 1/4:113 1/2:112 1/2:110 1/3:19 1/3:18 1/3:16 1/4:116 1/2:113 1/2:111 1/3:19 1/3:18 1/3:1
115:1115:1115:1115:156:156:156:156:156:156:125:125:125:125:125:125:16:16:16:16:16:1
1001001001001001001001001001006262626261502522191514
1001001001001001001001001001006262626262623328242019
1001001001001001001001001001006262626262623429252220
1001001001001001001001001001006262626262624135312623
FINALR.P.M. OUTPUT TORQUE (Nm)
WORM
RATIO
SPUR
GearboxSpecification
Motor Speed4000 r.p.m.
ContMotorRating
205 watts
1 HourMotorRating
265 watts
ContMotorRating
280 watts
1 HourMotorRating
340 watts
PM 50 LWS PM 60 LWS
1.224
4.85.77
7.68.69.811.41213
15.51719
25.54049607080
30:116 1/2:18 1/3:17 1/4:112 1/2:110 1/3:19 1/3:18 1/3:17 1/4:16 1/4:113 1/2:112 1/2:110 1/3:19 1/3:18 1/3:16 1/4:116 1/2:113 1/2:111 1/3:19 1/3:18 1/3:1
115:1115:1115:1115:156:156:156:156:156:156:125:125:125:125:125:125:16:16:16:16:16:1
1001001001001001001001001001006262626261492522181514
1001001001001001001001001001006262626262623229242019
1001001001001001001001001001006262626262623429252220
1001001001001001001001001001006262626262624135312623
106
Ø 7
7
PM 50 LWS = 309PM 60 LWS = 322
40.6
15°
565651
226 44.75
Ø 4
7.6Ø 125
123
103.219 x 7.1
SLOT85.7
120
9.5
68.2
5
134
88.1
48.4
71
PM 50 LWSPM 60 LWS
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 50 LWS
Optional shaft at motor speed (lead end only) 10mm dia.�33mm long. Approx. weight: PM 50/60 LWS 6.80 Kg
107
15mm dia. h6.Keyway 5mm�38mm long.
Motor CL
4 holes on 70mm P.C.D.Can be tapped M5�11mm deep.
Alternative shaft positionon request.
Leads out here 30cm
Optional terminal box tapped 20mmconduit PG 13.5 on request.Standard entry position R.H.S.
Per
man
ent
Mag
net
Worm and Multi-Spur Reduction Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosures: – PM 50 – Totally Enclosed (IP 54)PM 60 – Drip Proof Internal Fan Cooled (IP 21)
Gearbox Type:
LWSSpeed Range: 0.5 – 80 r.p.m.
OUTPUT TORQUE (Nm)FINALR.P.M.
RATIO
WORM SPUR
GearboxSpecification
Motor Speed4000 r.p.m.
ContMotor Rating
160 watts
15 MIN Motor Rating
250 watts
30 MIN Motor Rating
250 watts
1 Hour Motor Rating
265 watts
1 Hour Motor Rating
200 watts
ContMotor Rating
200 watts
ContMotor Rating
205 watts
15 MIN Motor Rating
375 watts
ContMotor Rating
280 watts
1 Hour Motor Rating
340 watts
15 MIN Motor Rating
460 watts
PM 5 GWS PM 6 GWS PM 50 GWS PM 60 GWS
1.22.23.957101116192630445971
30:116 1/2:19 1/3:17 1/4:15 1/8:17 1/4:16 1/6:110 1/3:18 1/3:16 1/6:112 1/3:18 1/3:16 1/6:15 1/8:1
110:1110:1110:1110:1110:157:157.125.125:125:111:111:111:111:1
250250180152110786845393124181412
250250225190137978557493930231815
25025025023717112110771614837282219
250250225190137978557493930231815
25025025023717112110771614837282219
2502502301941401008758504031231816
25025025025018212911375655140302420
250250250250250182159105917356423328
25025025025023316514590836651383026
2502502502502502241951291128969524135
108
25025025025019213612079695442322521
Ø 7
7
40.6
151.
5
55
137
Ø 5
4
PM 5 GWS = 296 PM 6 GWS = 309
3
PM 50 GWS = 314 PM 60 GWS = 327
Ø 87.4
15°
28.4114
4.676
104
85
142
= 120 =
71
Dimensions in mm. Scale 1:4NB: Unit drawn is PM 50 GWS
Optional terminal box tapped 20mmconduit or PG 13.5 on request.Shown standard position entry R.H.S.
Leads out here 30cm
Motor CL
25mm dia. h6.Keyway 6mm�63mm long. Availableboth sides.Also available with hollow shaft 15mminternal diameter with 5mm keyway.
Optional (either side): 4 holeson 75mm P.C.D. Can betapped M6�19mm deep.
4 holes tappedM10�20mm deep.
Approx. weight: PM 5/6 GWS – 9.65 KgPM 50/60 GWS – 9.90 KgOptional shaft at motor speed (lead end only) 10mm dia.�33mm long.
PM 5 GWS – PM 50 GWSPM 6 GWS – PM 60 GWS
PM 50 GWS
(1 Nm = 10,2 cmkp)
Worm and Multi-Spur Reduction Gear UnitsVariable Speed – D.C. Permanent Magnet
Enclosures: – PM5 – PM50 – Totally Enclosed (IP 54)PM6 – PM60 – Drip Proof Internal Fan Cooled (IP 21)
Gearbox Type:
GWSSpeed Range: 1.2 – 71 r.p.m.
� Voltage, Construction, Connections, Motor PerformanceSpecifications and Optional Extrassee pages 72 and 74 for full details.GWS gearbox with hollow shaft available on request(15mm internal diameter with 5mm keyway).
Mot
or C L