Parts and Accessories Installation Instructions · Installation Instructions No . 01 29 0 153 229...
Transcript of Parts and Accessories Installation Instructions · Installation Instructions No . 01 29 0 153 229...
Parts and AccessoriesInstallation Instructions
Universal BMW Bluetooth Hands-Free Kit RetrofitBMW 3 Series Coupé and Saloon (E 46/2/4) from 09/01
Important information
The retrofit kit is for use within the BMW dealership organisation only.
Subject to technical modifications.
Target group
The target group for these installation instructions is specialist personnel trained on BMW cars with the appropriate specialist knowledge.
All work must be completed using the latest BMW repair manuals, circuit diagrams, servicing manuals and work instructions in a rational order using the prescribed tools (special tools) and observing current health and safety regulations.
Installation information
Ensure that the cables/lines are not kinked or damaged as you install them in the car.
The installed cables are to be secured with cable ties.
If the specified PIN chambers are occupied, bridges, double crimps or twin-lead terminals must be used.
Ordering instructions
The black telephone console insert is supplied in the retrofit kit.
An insert for the centre console in other colours for cars with different interior colours can be ordered if required. See the EPC for all further ordering information.
The snap-in adapter is not part of the retrofit kit and must be ordered separately.
List of special equipment
The following special equipment must be taken into consideration when installing the retrofit kit. The various sections contain corresponding information.
SA 403 Glass roof
SA 602 On-board monitor
SA 606 Radio navigation system
SA 609 Navigation system
SA 660 BMW Reverse radio
SA 661 BMW Business radio
SA 663 BMW Professional radio
Installation time
Approx. 5 hours, but this may vary depending on the condition of the car and the equipment in it.
Pictograms
Retrofit kit No. 84 64 0 153 221Installation Instructions No. 01 29 0 153 229 Issue date: 08.2002
Pictograms
denotes instructions that draw your attention to special features.
� denotes the end of the instruction or caution text.
Retrofit kit No.
84 64 0 153 221
84 64 0 302 157
Special tools required
None
EN/2Retrofit kit No. 84 64 0 153 221Installation Instructions No. 01 29 0 153 229 Issue date: 08.2002
Contents
Section Page
1. Preparations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Retrofit wiring harness connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4. Installation and cabling diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5. To install and connect the retrofit wiring harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6. To install and connect the universal charger/hands-free electronic control unit (cars with SA 660/661/663 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7. To install and connect the universal charger/hands-free electronic control unit (cars with SA 602/606/609 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
8. To install and connect the eject box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
9. To install the hands-free microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
10. Concluding work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
11. Circuit diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
EN/3Retrofit kit No. 84 64 0 153 221Installation Instructions No. 01 29 0 153 229 Issue date: 08.2002
1. Preparations
0
TIS instruction No.
Conduct a brief test ---
Disconnect the negative pole of the battery 12 00 ...
The following components must be removed first of all:
Boot trim on the left 51 47 151
Rear seat bench 51 24 005
Rear seat backrest 51 24 010
Front left door sill trim 51 47 000
Rear left door sill strip 51 47 030
Front left seat 52 .. ...
B pillar trim at the bottom left 51 43 150
Glove box, left 51 16 350
Pedal trim 51 15 185
A pillar trim in the left footwell 51 43 070
A pillar trim on the left 51 43 201
Left sun visor 51 16 080
Ceiling light 63 31 000
Oddments box support 51 16 ...
Finishing strips, centre and right 51 10 221
Heating system control 64 11 748
Radio 65 11 030
Oddments box 51 16 200
EN/4Retrofit kit No. 84 64 0 153 221Installation Instructions No. 01 29 0 153 229 Issue date: 08.2002
2. Parts list
0
Legend0
A Multi wiring harness II
B Aerial cable
C Eject box
D Telephone console insert
E Holder for WDCT aerial
F WDCT aerial
G Hands-free microphone
H ULF (universal charger/hands-free electronic control unit)
I ULF holder (cars with SA 660/661/663 only)
J ULF holder (cars with SA 602/606/609 only)
K Speed nut St 4.2 (2x)
L Hexagonal nut M5 (5x)
M Hexagonal screw M5 x 14 (6x)
N Speed nut M5 (6x)
A CB D
FE
JK L M N
G H I
��� ���� �
EN/5Retrofit kit No. 84 64 0 153 221Installation Instructions No. 01 29 0 153 229 Issue date: 08.2002
3. Retrofit wiring harness connection diagram
0
0
Item Description SignalCable colour / Cross-section
Connection location in the car Abbreviation / Slot
A Multi wiring harness --- --- --- ---
A1 SW 54-pin plug--- ---
To universal charger/hands-free electronic
control unit
X4038
A2 SW Fakra plug contact --- --- To standard aerial cable X13323
A3 SW 18-pin plug --- --- To eject box X4545
A4 SW Fakra plug contact --- --- To the eject box X13322
A5 SW 10-pin plug LSP---
Cars with SA 660/661/663 onlyTo the radio plug
X13598
A6 Socket contact
Mute
Tel-On
WS/BR
0.35 mm2
WS/GN
0.35 mm2
Cars with SA 660/661/663 only
To the radio plug X18126PIN 4
X18126
PIN 10
A7 Twin-lead terminal
SW 8-pin plug--- ---
Between audio plugs X322
A8 SW 3-pin plug Mic --- To hands-free microphone X13293
A9 SW 3-pin plug --- --- To the aerial booster X1765
A10 Cable eyelet Terminal 31 --- To the earth post in the boot on the left X13016
A11 SW 12-pin plug LSP---
Cars with SA 602/606/609 only
To radio receiver plug X13321
A12 Socket contact
Mute
Tel-On
WS/BR
0.35 mm2
WS/GN
0.35 mm2
Cars with SA 602/606/609 only
To radio receiver plug X18126
PIN 10
X18126
PIN 11
B Aerial cable --- --- --- ---
B1 SW Fakra plug contact --- --- To WDCT aerial ---
B2 WS Fakra plug contact--- ---
To universal charger/hands-free electronic
control unit---
A1
B1 B2
A12
A11
A5
A6
A3
A4
A2
A7
A8
A10 A9
A
B
��� ���� �
EN/6Retrofit kit No. 84 64 0 153 221Installation Instructions No. 01 29 0 153 229 Issue date: 08.2002
4. Installation and cabling diagram
0
Legend
A Multi wiring harness II
B Aerial cable
C Eject box
F WDCT aerial
G Hands-free microphone
H ULF (universal charger/hands-free electronic control unit)
1 Audio plug X322
2 Radio plug X18126 (with SA 660/661/663 only)
3 Radio plug X18126 (with SA 602/606/609 only)
4 Earth post X13016
HB
CG1
A
3 42
F
��� ���� �
EN/7Retrofit kit No. 84 64 0 153 221Installation Instructions No. 01 29 0 153 229 Issue date: 08.2002
5. To install and connect the retrofit wiring harness
0
0
0
0
0
Screw branch A10 to earth post X13016.
0
Cars with SA 660/661/663 only
Insulate branches A11 and A12 and tie them back.
Cars with SA 602/606/609 only
Disconnect plug X18126 from the radio receiver (1).
0
Connect branch A12 as follows to plug X18126:
- WS/BR cable in PIN 10
- WS/GN cable in PIN 11
0
Connect branch A11 to plug X18126.
If the plug X13321 is already in the car, the two cables from branch A11 must be disconnected and connected to the same pins in the plug in the car X13321.
X13016
A10
��� ���� �
X18126
1
046 0723 Z
A12
X18126
046 0724 Z
A11
X18126
046 0725 Z
EN/8Retrofit kit No. 84 64 0 153 221Installation Instructions No. 01 29 0 153 229 Issue date: 08.2002
5. To install and connect the retrofit wiring harness
0
0
0
0
0
All cars
Install branches A3 – A8 as follows:
- Branches A3 and A4 to the centre console.
- Branches A5 – A7 to the radio.
- Branch A8 to the A pillar.
Cars with SA 602/606/609 only
- Insulate branches A5 and A6 and tie them back.
0
All cars
Lay branch A8 to the installation site of the hands-free microphone.
0
Disconnect plug X322.
Connect branch A7 in parallel between plug X322.
0
Cars with SA 660/661/663 only
Connect branch A6 as follows to plug X18126:
- WS/BR cable in PIN 4
- WS/GN cable in PIN 10
A8
A3-A4
A5-A7
��� ���� �
A8
��� ���� �
X322
A7
X322
046 0540 Z
X18126A6
��� ���� �
EN/9Retrofit kit No. 84 64 0 153 221Installation Instructions No. 01 29 0 153 229 Issue date: 08.2002
5. To install and connect the retrofit wiring harness
0
0
Connect branch A5 to plug X18126.
If the plug X13321 is already in the car, the two cables from branch A5 must be disconnected and connected to the same pins in the plug in the car X13321.
X18126
A5
��� ���� �
EN/10Retrofit kit No. 84 64 0 153 221Installation Instructions No. 01 29 0 153 229 Issue date: 08.2002
EN/11Retrofit kit No. 84 64 0 153 221
6. To install and connect the universal charger/hands-free electronic control unit (cars with SA 660/661/663 only)
0
0
0
0
0
Push the speed nuts N onto the holder I.
0
Use the hexagonal screws M to screw the universal charger/hands-free electronic control unit H onto the holder I.
0
Push the speed nuts N on in the boot at the rear left.
0
Use the hexagonal screws M to screw on the holder I in the boot at the rear left.
I
N
��� ���� �
IH
M��� ���� �
N
��� ���� �
I
M
��� ���� �
Installation Instructions No. 01 29 0 153 229 Issue date: 08.2002
6. To install and connect the universal charger/hands-free electronic control unit (cars with SA 660/661/663 only)
0
0
Connect branches A1 and B2 to the universal charger/hands-free electronic control unit H.
H
A1
B2��� ���� �
EN/12Retrofit kit No. 84 64 0 153 221Installation Instructions No. 01 29 0 153 229 Issue date: 08.2002
7. To install and connect the universal charger/hands-free electronic control unit (cars with SA 602/606/609 only)
0
0
0
0
Use the hexagonal nuts L to screw the universal charger/hands-free electronic control unit H onto the holder J.
0
Connect branches A1 and B2 to the universal charger/hands-free electronic control unit H.
0
Use the hexagonal screws M to screw the holder J onto the module holder.
L
H
J
��� ���� �
B2
H
A1
��� ���� �
M
J
��� ���� �
EN/13Retrofit kit No. 84 64 0 153 221Installation Instructions No. 01 29 0 153 229 Issue date: 08.2002
8. To install and connect the eject box
0
0
0
0
0
Put the WDCT aerial F onto the holder E and screw it on using hexagonal nuts L.
Connect the branch B1 to the WDCT aerial F.
0
Insert the WDCT aerial and holderE into the mounting in the centre console (1).
Push on the speed nuts I.
00
Clip the eject box C into the telephone console insert D.
0
Clip the telephone console insert and eject box C into the oddments box (1).
L
E
B1F
��� ���� �
IE
1
��� ���� �
C
D��� ���� ���� ���� �
C
1��� ���� �
EN/14Retrofit kit No. 84 64 0 153 221Installation Instructions No. 01 29 0 153 229 Issue date: 08.2002
8. To install and connect the eject box
0
0
Connect the branch A3 to the black 18-pin plug (1) of the eject box.
Connect the branch A4 to the FAKRA plug of the eject box (2).
A3
A42
1
��� ���� �
EN/15Retrofit kit No. 84 64 0 153 221Installation Instructions No. 01 29 0 153 229 Issue date: 08.2002
9. To install the hands-free microphone
0
0
0
0
0
Cars with SA 403 only
Connect branch A8 to the hands-free microphone G.
The arrow on the hands-free microphone G must point to the front of the car.
Clip the hands-free microphone G into the trim (1).
0
Cars without SA 403 only
Only use the template from the installation kit.
Cut out the template (1) and affix it to the headlining behind the opening for the interior light.
Cut the hatched area (3) out of the headlining.
0
Push the metal frame (1) through the opening (2) and clip it to the retaining frame (3).
0
Connect branch A8 to the hands-free microphone G.
The arrow on the hands-free microphone G must point to the front of the car.
Clip the hands-free microphone G into the trim (1).
G
1A8
��� ���� �
1
2
3
��� ���� �
2
1
3
��� ���� �
G
1A8
��� ���� �
EN/16Retrofit kit No. 84 64 0 153 221Installation Instructions No. 01 29 0 153 229 Issue date: 08.2002
10. Concluding work
0
This retrofit system requires coding and must be coded using the “Retrofit” path.
- Connect battery
- Conduct a brief test with DISPlus/MoDiC III/GT1.
- Synchronize the mobile phone and the universal charger/hands-free electronic control unit
- Activate the Bluetooth function of the mobile phone (see the mobile phone owner's manual)
- Press and hold the push-to-talk button for about 1 second whilst switching on terminal R
- Release the push-to-talk button. The radio display shows "BT PAIRING" and the MID or on-board monitor displays "BLUETOOTH PAIRING".
The checklamps on the MID or on-board monitor flash during the connection phase.
- Activate the "Locate Bluetooth Devices" menu on the mobile phone (see the mobile phone owner's manual). This process may take a few minutes.
- Work through additional menus in accordance with the instructions displayed on the mobile phone
- When prompted to do so, enter the 4 digit "BLUETOOTH PASSKEY" (see the sticker on the owner's manual) using the mobile phone keypad
- The radio, MID or on-board monitor displays "PAIRING SUCCEEDED" to confirm that synchronisation has been carried out correctly
- Switch off the ignition – the connection is terminated
- Conduct a function test
- Assemble the car again following the instructions to dismantle it in reverse order
EN/17Retrofit kit No. 84 64 0 153 221Installation Instructions No. 01 29 0 153 229 Issue date: 08.2002
11. Circuit diagram
If required, the circuit diagram for the multi wiring harness II can be referred to in the “Multi Wiring Harness II Circuit Diagrams” installation instructions, PN: 01 29 0 146 544, in TeTis or the EBA CD.
EN/18Retrofit kit No. 84 64 0 153 221Installation Instructions No. 01 29 0 153 229 Issue date: 08.2002