Installation should be performed by a qualified electrician in accordance with the National Electrical Code

and relevant local codes.INSTALLATION INSTRUCTIONS

PARADOX SERIESPDX7

©2014 Acuity Brands Lighting, Inc.7/14/14INS-PDX7

NOTE: Hydrel Reserves The Right To Modify Specification Without Notice. Any dimension on this sheet is to be assumed as a reference dimension: “Used for information purposes only. It does not govern manufacturing or inspection requirements.” (ANSI Y14.5-1973)

20660 Nordhoff St., Suite B | Chatsworth, CA 91311Phone: 866.533.9901 | Fax: 866.533.5291

www.hydrel.com

TO INSTALL: 1. Dig a hole to appropriate depth allowing for rough-in-section to

be secured to conduit.

2. To install with door flush to finish grade: 2a. Mount Rough-in-Section (RIS) with flush pour shield placed at finish grade.

Leave temporary cover plate in place while installing housing.

Flush Pour Shield

Temporary Cover Plate

Rough-in-Section (RIS)

Rough-in-Section (RIS)

Rough-in-Section (RIS)

Flush Pour Shield

TemporaryCover Plate

Pour Screw

Finish Grade

DoorFinish Grade

Finish Grade

Enlarged detail with door installed.

Enlarged detail with temporary cover plate and flush pour shield.

Rough-in-Section (RIS) before pouring finish grade

Rough-in-Section (RIS) after pouring finish grade

Temporary Screws

1

Installation should be performed by a qualified electrician in accordance with the National Electrical Code

and relevant local codes.INSTALLATION INSTRUCTIONS

PARADOX SERIESPDX7

©2014 Acuity Brands Lighting, Inc.7/14/14INS-PDX7

NOTE: Hydrel Reserves The Right To Modify Specification Without Notice. Any dimension on this sheet is to be assumed as a reference dimension: “Used for information purposes only. It does not govern manufacturing or inspection requirements.” (ANSI Y14.5-1973)

20660 Nordhoff St., Suite B | Chatsworth, CA 91311Phone: 866.533.9901 | Fax: 866.533.5291

www.hydrel.com

3. To install with Rough-in-Section (RIS) flush to finish grade: 3a. Remove flush pour shield from Rough-in-Section (RIS). 3b. Re-attach temporary cover plate onto Rough-in-Section (RIS). 3c. Mount Rough-in-Section with temporary cover plate placed at finish grade.

Temporary Screws

Flush Pour Shield

Temporary Cover Plate

Rough-in-Section(RIS)

Door Screw

Finish Grade

Temporary Cover Plate

Rough-in-Section (RIS)

Rough-in-Section (RIS)

Finish Grade

DoorFinish Grade

1/8”Enlarged detail with temporary cover plate.

Enlarged detail with door installed.

Rough-in-Section (RIS) before pouring finish grade.

Rough-in-Section (RIS) after pouring finish grade.

2

Installation should be performed by a qualified electrician in accordance with the National Electrical Code

and relevant local codes.INSTALLATION INSTRUCTIONS

PARADOX SERIESPDX7

©2014 Acuity Brands Lighting, Inc.7/14/14INS-PDX7

NOTE: Hydrel Reserves The Right To Modify Specification Without Notice. Any dimension on this sheet is to be assumed as a reference dimension: “Used for information purposes only. It does not govern manufacturing or inspection requirements.” (ANSI Y14.5-1973)

20660 Nordhoff St., Suite B | Chatsworth, CA 91311Phone: 866.533.9901 | Fax: 866.533.5291

www.hydrel.com

REBAR

CONDUIT

CONDUIT

CAUTION: When installing in organic mulch, surround rough-in section with approximately six inches (15cm) of sand or other non-organic substance.

Install fixture flush per step 2 / 3.

Secure rough-in section to rebar to prevent “floating.”

Install suitable thread sealing compound

when connecting conduit (side or bottom

entry).

4. For optional rebar anchoring: Secure rebar as shown (rebar by others). **Do not penetrate the housing when securing re-bar.**

FINISH GRADE

3

Installation should be performed by a qualified electrician in accordance with the National Electrical Code

and relevant local codes.INSTALLATION INSTRUCTIONS

PARADOX SERIESPDX7

©2014 Acuity Brands Lighting, Inc.7/14/14INS-PDX7

NOTE: Hydrel Reserves The Right To Modify Specification Without Notice. Any dimension on this sheet is to be assumed as a reference dimension: “Used for information purposes only. It does not govern manufacturing or inspection requirements.” (ANSI Y14.5-1973)

20660 Nordhoff St., Suite B | Chatsworth, CA 91311Phone: 866.533.9901 | Fax: 866.533.5291

www.hydrel.com

8. Loosen junction box screw and remove lid. IMPORTANT NOTE: DO NOT lose screw assembly. Screw assembly contains sealing gaskets. It MUST be used to reinstall junction box lid in Step 10.

9. Pull electrical supply conductors and make wire splice in accordance with NEC.

10. Reinstall junction box lid with gas-keted screw provided. Ensure screw is straight, mis-threading can cause leaking. CAUTION: TIGHTEN MINIMUM (35 IN-LBS OR 3.95 n-M).

Temporary Screws

Flush Pour Shield

Temporary Cover Plate

Rough-in-Section (RIS)

Junction Box

Junction Box

Rough-in-Section (RIS)

3/4” NPT

5. Connect 3/4” NPT conduit to junction box (side or bottom entry). Seal con duit entry using suitable thread sealing compound to ensure conduit is watertight and to prevent moisture penetration from conduit system.

6. Pour concrete to finish grade or backfill with dirt.

7. Remove temporary cover and flush pour shield. Remove 3 set screws 120° apart.

4

Installation should be performed by a qualified electrician in accordance with the National Electrical Code

and relevant local codes.INSTALLATION INSTRUCTIONS

PARADOX SERIESPDX7

©2014 Acuity Brands Lighting, Inc.7/14/14INS-PDX7

NOTE: Hydrel Reserves The Right To Modify Specification Without Notice. Any dimension on this sheet is to be assumed as a reference dimension: “Used for information purposes only. It does not govern manufacturing or inspection requirements.” (ANSI Y14.5-1973)

20660 Nordhoff St., Suite B | Chatsworth, CA 91311Phone: 866.533.9901 | Fax: 866.533.5291

www.hydrel.com

11. Ensure power module and incoming power are compatible voltages. Insert power supply module (HID Ballast, Fluorescent Ballast, LED Power Supply, Low Voltage Transformer) into hous-ing. Connect using Hydrel pro-vided silicone filled wire nuts to pre-installed housing wiring.

Power Supply Module

SUPPLY POWER - LINE VOLTAGE

0-10 LOW VOLTAGE DIMMING LINE-+

LED DIMMING

PDX7 WIRING

DRIVER

SPLICE SPLICE SPLICE

WICKING BARRIER

SUPPLY POWER

LINE VOLTAGE

DRIVER

-+

SPLICE

JUNCTION BOX

WICKING BARRIER

JUNCTION BOX

5

Tie all 3 black wires from LED array together

Tie all 3 black wires from LED array together

Installation should be performed by a qualified electrician in accordance with the National Electrical Code

and relevant local codes.INSTALLATION INSTRUCTIONS

PARADOX SERIESPDX7

©2014 Acuity Brands Lighting, Inc.7/14/14INS-PDX7

NOTE: Hydrel Reserves The Right To Modify Specification Without Notice. Any dimension on this sheet is to be assumed as a reference dimension: “Used for information purposes only. It does not govern manufacturing or inspection requirements.” (ANSI Y14.5-1973)

20660 Nordhoff St., Suite B | Chatsworth, CA 91311Phone: 866.533.9901 | Fax: 866.533.5291

www.hydrel.com

14. Ensure the sealing surface and all screw holes are free from debris and thouroughly cleaned before installing the door. Remove three of the eight temporary set screws located at the upper ring of the fixture body and discard.

15. Install door lens assembly ensuring screws are tight.NOTE:Torque the three door screws of the PDX7 between 22in-lbs and 25in-lbs.

Tighten screws until the bottom of the door touches the top of the housing. Tighten screw extra 1/16 to 1/8 turn beyond contact point.

Screw is made with a premium heat treated stainless steel with Teflon coating. This heat treatment gives this screw a greater ultimate strength than standard 18-8.

Door Lens Assembly

12. Install lamp module. Connect to modular power supply using Hydrel provided silicone filled wire nuts.

13. Adjust lamp/reflector as-sembly to aim. Secure with locking/aiming screws.

Lamp Module

6

Installation should be performed by a qualified electrician in accordance with the National Electrical Code

and relevant local codes.INSTALLATION INSTRUCTIONS

PARADOX SERIESPDX7

©2014 Acuity Brands Lighting, Inc.7/14/14INS-PDX7

NOTE: Hydrel Reserves The Right To Modify Specification Without Notice. Any dimension on this sheet is to be assumed as a reference dimension: “Used for information purposes only. It does not govern manufacturing or inspection requirements.” (ANSI Y14.5-1973)

20660 Nordhoff St., Suite B | Chatsworth, CA 91311Phone: 866.533.9901 | Fax: 866.533.5291

www.hydrel.com

LAMP ADJUSTMENT DETAIL

1. Loosen two tilt screws. 2. Tilt lamp.

3. Tighten two tilt screws.

4. Lock rotational ring screw.

7