PanelView Plus Terminals

Selection Guide

Visualization Solutions

PanelView Plus Terminals

PanelView Component Terminals

Industrial Computers and Monitors

www.klinkmann.com6 / 2011

http://literature.rockwellautomation.com/idc/groups/literature/documents/td/ic-td001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/td/2711c-td001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/td/2711p-td005_-en-p.pdf

2 Rockwell Automation Publication VIEW-SG001F-EN-P - October 2010

Whats Inside

This selection guide is meant to help make initial decisions for the visualization products best suited for your system requirements. For detailed technical specifications, certifications, and environmental specifications, see the documentation links on the front cover of this selection guide.

For assistance and validation in making final product selections, consider using the Configuration and Selection tools available at http://www.rockwellautomation.com/en/e-tools/index.html

Topic Page

Visualization Platforms 4

HMI Terminal Comparison 6

PanelView Plus Terminals 7

Typical Configurations 8

PanelView Plus 6 Terminals 10

PanelView Plus 400 and 600 Terminals 16

PanelView Plus Compact Terminals 19

PanelView Component Terminals 26

Industrial Computers and Monitors 30

Typical Configurations 31

Integrated Display Computers 32

Integrated Display Computers with Keypad 37

Hazardous Location Computers 39

Non-display Computers 40

Compact Non-display Computers 43

Industrial Monitors 45

HMI Software 48


http://www.rockwellautomation.com/en/e-tools/index.html

Rockwell Automation Publication VIEW-SG001F-EN-P - November 2010 3

Introduction

Adding Visualization to Your Control System

As a machine builder or end user, you design control solutions with an eye toward improving safety, higher levels of performance and efficiency, and better integration with the rest of the manufacturing operation. To achieve these goals, you need a scalable, modular control system that offers safety, throughput and information management capabilities to match each applications requirements.

The Rockwell Automation Integrated Architecture system is unique in that it offers scalable, integrated safety, motion control, and visualization capabilities that are ideal for machine builders and end users who want a single control and development environment, regardless of the application size or complexity.

The visualization products comprise a suite of scalable HMI software and operator interface hardware that provide plant floor machine operators, supervisors, engineers, and business managers a window to critical data, and production and process information. And all this can be done from the plant floor or remotely from a web browser.

Whether its a machine-level or site-level HMI, a Windows CE platform, a smaller component HMI, or an industrial computer, Rockwell Automation has a portfolio of visualization solutions to match your system requirements.

PanelView Plus terminals, FactoryTalk View Machine Edition, and FactoryTalk View Site Edition provide premier integration in a number of ways.

Reduce programming time with Logix native addressing and the ability to browse directly to Logix tags without creating a separate database.

Simplifies interaction of all networks with support for all Core Integrated Architecture CIP networks including EtherNet/IP, ControlNet, and numerous other drivers.

Simplifies development time with pre-engineered, pre-tested faceplates for specific motion, drives, and process applications.


Visualization Platforms www.klinkmann.com6 / 2011

Visualization Platforms

PanelView Plus Family PanelView Component Family

page 26page 7

Select an Operator Interface

Do you need: Machine-level HMI with

FactoryTalk View ME? Dedicated platform? Component level HMI?

Yes

No

Machine-level HMI

Do you need a machine-level HMI? Small to large applications FactoryTalk View ME software ControlLogix or CompactLogix controllers

Do you need a component-level HMI?: Small applications Web-based software MicroLogix, SLC controller, or device

Select a PanelView ComponentConsider: Display size Monochrome or color display Operator input Communication With or without battery backup

Select a PanelView PlusConsider: Windows CE desktop access Remote access and file viewers Display size Operator input Power requirements Communication Environmental requirements

Select Accessories Cables

Select FactoryTalk View ME software Optional communication module Accessories Cables

For technical specifications, certifications, and environmental specifications on the PanelView Plus terminals, refer to the PanelView Plus Specifications Technical Data, publication 2711P-TD005

For technical specifications, certifications, and environmental specifications on the PanelView Component terminals, refer to the PanelView Component Specifications Technical Data, publication 2711C-TD001

4 Rockwell Automation Publication VIEW-SG001F-EN-P - November 2010

http://literature.rockwellautomation.com/idc/groups/literature/documents/td/2711p-td005_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/td/2711c-td001_-en-p.pdf

Visualization Platformswww.klinkmann.com6 / 2011

Industrial MonitorsIntegrated Display Computers Non-display Computers

Select Accessories

Performance page 45

Standard page 45

Non-displaypage 40

Compact Non-displaypage 43

Integrated Displaypage 32

Display with Keypadpage 37

Select an Industrial Computer

Do you need: Site-level HMI with

FactoryTalk View SE? Open platform? Processing power of an

industrial computer?

Yes

Hazardous Location Computers

Select FactoryTalk View software if needed Accessories

Hazardous Locationpage 39

Select FactoryTalk View software if needed Accessories

Site-level HMI

HMI Servers

FactoryTalkData Server

Data Servers

Do you need: Integrated display? Integrated display with keypad? Rockwell Software and

third-party software?

Do you need: Extended temperature range? Class 1 Div 2 certification? Rockwell Software and


Do you need: Computer without a display? Compact form factor option? Rockwell Software and


Do you need: Monitor only? Class 1 Div 2 certification? Standard industrial environment?

Select a Display ComputerConsider: Display size and input method Resistive touch screen Solid-state or hard-disk drive Standard or performance options Operating system Power requirements Bezel type

Select Hazardous Location Computer

Consider: Computer with display Computer without display

Select a Non-display ComputerConsider: Environmental requirements Compact form factor Solid-state or hard-disk drive Power requirements Operating system Mounting method Standard or performance options

Select a MonitorConsider: Environment Display size Touch screen option Bezel type Mounting method

Select FactoryTalk View Software if needed Accessories

For technical specifications, certifications, and environmental specifications on the industrial computers and monitors, refer to the Industrial Computers and Monitors Specifications Technical Data, publication IC-TD001.


http://literature.rockwellautomation.com/idc/groups/literature/documents/td/ic-td001_-en-p.pdf


HMI Terminal Comparison

HMI Terminal Comparison This table provides a quick glance at comparisons between the different HMI terminal platforms.

Table 1 - HMI Terminal Comparison

Characteristic 2711P PanelView Plus 6700, 1000, 1250, 15002711P PanelView Plus

400, 6002711P PanelView Plus Compact 400, 600, 1000

2711C PanelView ComponentC200, C300, C600, C1000

Display 700: 6.5 in. color TFT1000: 10.4 inch color TFT1250: 12.1 in. color TFT1500: 15 in. color TFT

400: 3.5 in. color, 400: 3.8 in. grayscale600: 5.5 in. color TFT600: 5.5 in. grayscale TFT

400: 3.5 in. color400: 3.8 in. grayscale600: 5.5 in. color TFT100: 10.4 in. color TFT

C200: 2 in. monoC300: 3 in. monoC600: 5.7 in. color or monoC1000: 10.4 in. color

Input type All models: keypadAll models: touch screenAll models: key/touch

400: key/touch (3.5 in.)400: keypad (3.8 in.)600: touch screen

400: key/touch (3.5 in.)400: keypad (3.8 in.)600/1000: touch screen

C200: 4-keys C200: 10-keys+numeric C300: 10-keys/+numeric C600/C1000: touch screen

Built-in communication ports

RS-232EtherNet2 USB host and 1 USB device

RS-232EtherNet1 USB

RS-232EtherNet1 USB: 400/6002 USB: 1000

RS-232RS-422/RS-4851 USB host and 1 USB deviceEtherNet: C600/C1000C only

Add-on communication module

DH+DH-485ControlNet

DH+DH-485ControlNet

None None

Serial communication RS-232: DF1 or DH-485 RS-232: DF1 or DH-485 RS-232: DF1 or DH-485 RS-232: DF1 full-duplex, DH-485, multivendor optionsRS-485

Programming software FactoryTalk View ME 6.0 or laterViewPoint web server 1.2 or later

FactoryTalk View ME 5.1 or earlier FactoryTalk View ME 5.1 or later Web-enabled softwareresident in terminalPC-based emulator available

Operating system Windows CE 6.0 operating systemsupports this features: FTP Server VNC client/server PDF reader Active X controls Third-party device support

Additional functionality is available by ordering terminals with optional extended features(1) Internet Explorer web browser Remote desktop connection Media player File viewers for Microsoft Office

Word, PowerPoint, and Excel WordPad text editor

None None None

Open or closed system Open or closed desktop Closed Closed Closed

Memory 512 MB nonvolatile flash/512 MB RAM 64 MB nonvolatile flash/64 MB RAM 64 MB nonvolatile flash/64 MB RAM 20 MB nonvolatile flash/20 MB RAM

External storage Secure Digital (SD) cardUSB flash drives

CompactFlash CompactFlash USB flash: C200/C300USB flash/SD card: C600/C1000

Power AC or DC AC or DC DC DC

Preferred controller ControlLogix CompactLogix CompactLogix MicroLogix, SLC, PowerFlex 4 drive, Micro800

Capabilities High memory capacity desktop access enabled or disabled Multi-network/multivendor

connectivity Alarm messages (email alarms) Recipes Trending Data logging

Multi-network/multivendor connectivity

Alarm messages Recipes Trending Data logging

Single controller 25 displays 200 alarm messages Recipes Trending Data logging

Single device

PanelView Plus Terminalswww.klinkmann.com6 / 2011

PanelView Plus Terminals PanelView Plus devices give operators a clear view into monitoring and controlling applications. With FactoryTalk View Machine Edition already installed and activated, development time is reduced. The PanelView Plus family of products provides a broad range of rugged terminals that offer the following:

Premier integration with the Integrated Architecture platform Real-time monitoring of a terminals displays from a web browser Common development software Scalable 4 to 15-inch displays with a touch screen, keypad, or both

Figure 1 - Selecting a PanelView Plus Platform

Internet ExplorerRemote desktop connectionMicrosoft Office file viewersWordPad text editorMedia player (MPEG)

PanelView Plus 6 Terminals with extended features

See page 10

PanelView Plus 400 and 600 Terminals

See page 16

PanelView Plus Compact Terminals

See page 19

> 6-inch displayAccess to CE desktopWeb browser/file viewersRemote accessPDF readerMultiple apps

Do you need any of these?

Yes

No

Yes

Multiple controllers?> 25 displays> 200 alarms< 6-inch display?

Yes

No

For complete technical specifications, certifications, and environmental specifications on the PanelView Plus terminals, refer to the PanelView Plus Specifications Technical Data, publication 2711P-TD005


No


Cat. No. 2711P-xxxx9 or 2711P-RP9x

Cat. No. 2711P-xxxx8 or 2711P-RP8x

PanelView Plus 6 Terminals without extended features

See page 10


http://literature.rockwellautomation.com/idc/groups/literature/documents/td/2711p-td005_-en-p.pdf

PanelView Plus Terminals www.klinkmann.com6 / 2011

Typical Configurations Figure 2 shows a configuration where a PanelView Plus terminal is used with a Logix controller in standalone or machine-level mode using serial connectivity.

Figure 2 - Standalone Machine

In Figure 3, a PanelView Plus Compact terminal and the 1769-L3x CompactLogix system provide an integrated solution for midsize applications. Typically, these applications are machine-level control applications that require smaller I/O quantities and more communication capabilities than serial connectivity.

Figure 3 - Midsize Application

To Business Systems



In Figure 4, a PanelView Plus 6 terminal communicates with all devices by using EtherNet/IP communication. A Logix controller along with a Kinetix 300 servo drive offer a scalable power platform cost-sensitive applications, such as simple packaging machinery, indexing tables, automatic assembly equipment, tool changing machinery, and feed and withdrawal equipment.

Figure 4 - Indexing Motion

To Business Systems



PanelView Plus 6 Terminals This platform use modular components with value-added options for flexible system configuration. These components are usable across the entire PanelView Plus 6 platform and install with minimal effort:

Color display modules ranging from 6.5 to 15-inches in size with either key, touch screen, or combination key/touch-screen input

Windows CE logic modules providing desktop access Optional communication modules for network communication

Configured terminals with a display module and logic module can be ordered as a single catalog number or as separate components for field installation.

A high-bright display for outdoor use, plus conformal-coated and marine-certified components, extend this platforms ability to operate in environments with even more stringent and varying requirements.

The core component of this platform is the high-performance logic module that runs a closed or open Windows CE desktop environment with optional, extended features and file viewers. System integrators and OEMs can configure and deploy systems that allow or restrict desktop access.

Table 2 - Logic Module Features

Features Description

High memory capacity 512 MB nonvolatile flash and 512 MB RAM

Power input AC or DC

Network interface For optional DH+, DH-485, or ControlNet communication module

Communication ports Ethernet, RS-232 serial

USB ports 2 USB host ports for connecting a USB mouse, keyboard, printer, and USB flash drives that are hot swappable1 USB device port for connecting a host personal computer

Secure Digital (SD) card slot Hot-swappable card slot supports 1784-CDx SD cards for transferring files, upgrading firmware, or logging data

Operating system All terminals run the Windows CE 6.0 operating system (OS) providing OS functionality needed for most users needs: FTP server VNC client/server PDF reader Active X controls Third-party device support

Additional functionality is available by ordering terminals with optional, extended features: Internet Explorer web browser Remote desktop connection Media player Microsoft file viewers for PowerPoint, Excel, and Word WordPad text editor PDF reader

FactoryTalk View software FactoryTalk View Machine Edition software, version 6.0 or later, is preloaded and activated on each terminal

Single license support for FactoryTalk ViewPoint software, version 1.2 or later, gives remote users access to a terminals displays via standard web browser

HMI applications are developed with FactoryTalk View Studio for Machine Edition software, which is purchased separately

OptionalExtended Features



Product SelectionsBulletinNumber

InputType

Display Size

Display Type Communication Power Operating System Special Option

| | | | | | |

2711P- K = Keypad 7 = 6.5 in. C = Color 4 = Ethernet, RS-232 & (2) USB A = AC 8 = Windows CE 6.0 operating system K = Conformal-coated

T = Touch 10 = 10.4 in. D = DC 9 = Windows CE 6.0 operating systemwith extended features

B = Keypad/Touch 12 = 12.1 in.

15 = 15 in.

Table 3 - PanelView Plus 6 Terminals without Extended Features

Cat. No. Display Communication Input Power

Nonvolatile Flash/RAM MemoryKeypad Touch Keypad/Touch Size Type RS-232 Ethernet

700 Model

2711P-K7C4D8 2711P-T7C4D8 2711P-B7C4D8 6.5-in. Color DC 512 MB/512 MB

2711P-T7C4D8K(1) DC 512 MB/512 MB

2711P-K7C4A8 2711P-T7C4A8 2711P-B7C4A8 AC 512 MB/512 MB

1000 Model

2711P-K10C4D8 2711P-T10C4D8 2711P-B10C4D8 10.4-in Color DC 512 MB/512 MB


1250 Model


2711P-T12C4D8K(1) DC 512 MB/512 MB


1500 Model

2711P-K15C4D8 2711P-T15C4D8 2711P-B15C4D8 15-in. Color DC 512 MB/512 MB


(1) Conformal-coated terminal.

Table 4 - PanelView Plus 6 Terminals with Extended Features

Cat. No. Display Communication Input Power

Nonvolatile Flash/RAM MemoryKeypad Touch Keypad/Touch Size Type RS-232 Ethernet

700 Model

2711P-K7C4D9 2711P-T7C4D9 2711P-B7C4D9 6.5-in. Color DC 512 MB/512 MB


1000 Model



1250 Model



1500 Model

2711P-K15C4D9 2711P-T15C4D9 2711P-B15C4D9 15-in. Color DC 512 MB/512 MB




Accessories

Tables 517 list accessories for the PanelView Plus 6 terminals. Display modules, logic modules, and communication modules can be ordered as separate components for field installation.

Table 5 - Display Modules

Cat. No. Input Type Display Marine CertifiedConformal

CoatedBuilt-in

Antiglare Overlay

700 Model

2711P-RDK7C Keypad 7-in. color

2711P-RDK7CK Keypad

2711P-RDT7C Touch

2711P-RDT7CK Touch

2711P-RDT7CM Touch

2711P-RDB7C Keypad/Touch

2711P-RDB7CK Keypad/Touch

2711P-RDB7CM Keypad/Touch

1000 Model

2711P-RDK10C Keypad 10-4 in. color

2711P-RDT10C Touch

2711P-RDT10CM Touch


2711P-RDB10CM Keypad/Touch

1250 Model

2711P-RDK12C Keypad 12.1-in. color

2711P-RDK12CK Keypad

2711P-RDT12C Touch

2711P-RDT12CK Touch

2711P-RDT12AG Touch

2711P-RDT12H(1)

(1) This catalog number is a high-bright display module, indicated by the H at end of cat. no., that is designed for outdoor applications. The high-bright display module can be used only with DC-powered logic modules.

Touch


2711P-RDB12CK Keypad/Touch

1500 Model

2711P-RDK15C Keypad 15-in. color

2711P-RDT15C Touch

2711P-RDT15AG Touch




Table 6 - Logic Modules

Cat. No. Power InputNonvolatile Flash/

RAM Memory CommunicationConformal

Coated Included Software

Logic Modules without Extended Features

2711P-RP8A AC 512 MB/512 MB Ethernet RS-232 Network interface for

communication module

Windows CE 6.0 operating system without extended features/file viewers

FactoryTalk View Machine Edition runtime, version 6.0 or later

FactoryTalk ViewPoint software, version 1.2 or later

2711P-RP8D DC 512 MB/512 MB

2711P-RP8DK DC 512 MB/512 MB

Logic Modules with Extended Features

2711P-RP9A AC 512 MB/512 MB Ethernet RS-232 Network interface

communication module

Windows CE 6.0 operating system with extended features/file viewers

FactoryTalk View Machine Edition runtime, version 6.0 or later

FactoryTalk ViewPoint software, version 1.2 or later

2711P-RP9D DC 512 MB/512 MB

2711P-RP9DK DC 512 MB/512 MB

Table 7 - Communication Modules

Cat. No.Communication Conformal

CoatedMarine CertifiedDH+ DH-485 ControlNet (1)

(1) Scheduled and unscheduled communication.

2711P-RN6

2711P-RN6K

2711P-RN15S

2711P-RN15SK

Table 8 - Secure Digital (SD) Cards

Cat. No. Description

1784-SD1 1 GB Secure Digital (SD) card

1784-SD2 2 GB Secure Digital (SD) card

2711C-RCSD USB to SD adapter for secure digital card (SD)

Table 9 - Programming Cable

Cat. No. Description Length

2711C-CBL-UU02 USB host to USB device programming cable 2 m (6.5 ft)

Table 10 - Function Key Legend Inserts

Cat. No.PanelView Plus 6 Terminal Model(1)

(1) Applies to keypad and keypad/touch-screen terminals.

Includes

2711P-RFK7 700 keypad

Blank legend inserts and software






Table 11 - Antiglare Overlays

Cat. No.(1)

(1) Three overlays are shipped with each catalog number.

PanelView Plus 6 Terminal Model

Operator Input

Keypad Touch Key/Touch

2711P-RGK7700

2711P-RGT7

2711P-RGK101000

2711P-RGT10

2711P-RGK121250

2711P-RGT12

2711P-RGK151500

2711P-RGT15

Table 12 - Solar Visor


2711P-RVT12 Solar visor for 1250 high-bright display module, cat. no. 2711P-RDT12H

Table 13 - Mounting Hardware

Cat. No. Description Quantity

2711P-RTMC Mounting clips 8

Table 14 - Battery Replacement


2711P-RY2032 Replacement battery 1

Table 15 - Power Supply and Power Terminal Blocks


2711P-RSACDIN DIN-rail power supply, AC-to-DC, 85265V AC, 4763 Hz 1

2711P-RTBAC3 AC power terminal block 10

2711P-RTBDC2 2-pin DC power terminal block 10



Table 16 - Backlight Replacements

Cat. No. PanelView Plus 6 Display Module Size SeriesNumber of Backlights

2711P-RL7C 700 A and B 1

2711P-RL7C2 C and D 1

2711P-RL10C 1000 A 1

2711P-RL10C2 B and C 1

2711P-RL12C 1250 A and B 2

2711P-RL12C2 C 1

2711P-RL15C 1500 B 2

Table 17 - Bezel Replacements

Cat. No. PanelView Plus 6 Terminal ModelOperator Input


2711P-RBK7

700

2711P-RBT7

2711P-RBB7

2711P-RBK10

1000

2711P-RBT10

2711P-RBB10

2711P-RBK12

1250

2711P-RBT12

2711P-RBT12H(1)

(1) Applies to the cat. no. 2711P-RDT12H 1250 high-bright display module.

2711P-RBB12

2711P-RBK15

1500

2711P-RBT15

2711P-RBB15



PanelView Plus 400 and 600 Terminals

The smaller PanelView Plus 400 and 600 terminals combine a 4 or 6-inch display in the same base unit with the logic, memory, power, and operator input. Color or grayscale displays render images as 18-bit color or 32 levels of gray. Flexible input options include keypad, touch screen, or combination keypad/touch screen. Other key features include the following:

Unique mounting mechanism requiring no tools and a single die-cut Replaceable labels for terminal or system identification Function key legend kit and software for customizing the function keys

legends on the 600 keypad terminals Two base-configured units provide support for either RS-232 or RS-232

and Ethernet communication.

Product Selections

Table 18 - PanelView Plus 400 and 600 Terminal Configurations

RS-232 Unit Ethernet and RS-232 Unit

RS-232 serial port USB port for keyboard, mouse, or other

USB device CompactFlash slot for file transfers, data

logging, or system upgrades

RS-232 serial port 10/100BaseT Ethernet port USB port for keyboard, mouse or other USB device CompactFlash slot for file transfers, data logging,

or system upgrades Network interface for optional communication

DH+, DH-485, or ControlNet module

BulletinNumber Input Type Display Size Display Type Communication Power

| | | | | |

2711P- K = Keypad 4 = 3.5 or 3.8 in. C = Color 5 = RS-232 & USB A = AC

B = Keypad/Touch 6 = 5.5 in. M=Grayscale 20 = Ethernet, RS-232, & USB pluscommunication module interface

D = DC

Table 19 - PanelView Plus 400 Terminals

Cat. No. Display Communication Input Power Flash/RAMKeypad Keypad/Touch Size Type RS-232 Ethernet Module

2711P-K4M5D 3.8-in. Grayscale DC 64 MB/64 MB

2711P-K4M5A AC 64 MB/64 MB

2711P-K4M20D (1) DC 64 MB/64 MB

2711P-K4M20A (1) AC 64 MB/64 MB

2711P-K4C5D 2711P-B4C5D 3.5-in. Color DC 64 MB/64 MB

2711P-K4C5A 2711P-B4C5A AC 64 MB/64 MB

2711P-K4C20D 2711P-B4C20D (1) DC 64 MB/64 MB

2711P-K4C20A 2711P-B4C20A (1) AC 64 MB/64 MB

(1) Catalog numbers have a network interface for an optional communication module.



Accessories

Tables 2126 lists accessories for the PanelView Plus 400 and 600 terminals.

Table 20 - PanelView Plus 600 Terminals

Cat. No. Display Communication Input Power Flash/RAMKeypad Touch Keypad/Touch Size Type RS-232 Ethernet Module

2711P-K6M5D 2711P-T6M5D 2711P-B6M5D 5.5-in. Grayscale DC 64 MB/64 MB

2711P-K6M5A 2711P-T6M5A 2711P-B6M5A AC 64 MB/64 MB

2711P-K6M20D 2711P-T6M20D 2711P-B6M20D (1) DC 64 MB/64 MB

2711P-K6M20A 2711P-T6M20A 2711P-B6M20A (1) AC 64 MB/64 MB

2711P-K6C5D 2711P-T6C5D 2711P-B6C5D 5.5-in. Color TFT DC 64 MB/64 MB

2711P-K6C5A 2711P-T6C5A 2711P-B6C5A AC 64 MB/64 MB

2711P-K6C20D 2711P-T6C20D 2711P-B6C20D (1) DC 64 MB/64 MB

2711P-K6C20A 2711P-T6C20A 2711P-B6C20A (1) AC 64 MB/64 MB

(1) Catalog numbers have a network interface for an optional communication module.

Table 21 - Communication Modules

Cat. No.Communication

DH+ DH-485 ControlNet(1)

(1) Scheduled and unscheduled communication.

RS-232 Isolated

2711P-RN3

2711P-RN8

2711P-RN15C

2711P-RN22C


Cat. No.(1)


Terminal ModelInput Type


2711P-RGK4 400 Grayscale

2711P-RGB4 400 Color

2711P-RGK6600 Grayscale or Color

2711P-RGT6

Table 23 - CompactFlash Cards


2711P-RC3 256 MB blank CompactFlash card


2711P-RCH CompactFlash to PCMCIA adapter



Table 24 - Power Terminal Blocks


2711P-RVAC AC power terminal block 10

2711P-TBDC DC power terminal block 10



2711P-RTFC Mounting levers 8

Table 26 - Function Key Legend Inserts

Cat. No. Terminal Model Includes

2711P-RFK6 600 keypad and keypad/touch Blank legend inserts and software



PanelView Plus Compact Terminals

The PanelView Plus Compact 400, 600, and 1000 terminals offer just the right hardware and software functionality to meet the needs of midsize applications. Any application created for a compact terminal is also compatible with the PanelView Plus terminals. Key features include the following:

Preferred HMI integration with CompactLogix controllers RS-232 serial port, Ethernet port, USB port (two on 1000 model), DC

power, and CompactFlash Type 1 slot Serial and Ethernet communication Connection to single controller by using either RSLinx Enterprise

software, version 5.20 or later, or KEPServer software 25 displays and 200 alarm messages supported in the FactoryTalk View

Compact Machine Edition application Fixed hardware configurations without the addition or replacement of

modular components

Product Selections

This table lists the fixed hardware configurations available for the PanelView Plus Compact terminals.

Table 27 - PanelView Plus Compact

Cat. No. Input TypeDisplay Communication Input

Power Flash/RAMSize Type RS-232 Ethernet

2711PC-K4M20D Keypad 3.8-in. Grayscale DC 64 MB/64 MB

2711PC-B4C20D Keypad/Touch 3.5-in. Color DC 64 MB/64 MB

2711PC-T6M20D Touch 5.5-in Grayscale DC 64 MB/64 MB

2711PC-T6C20D Touch 5.5-in Color DC 64 MB/64 MB

2711PC-T10C4D1 Touch 10.4-in Color DC 64 MB/64 MB



AccessoriesTables 28 33 lists accessories for the PanelView Plus Compact terminals.

Table 28 - CompactFlash Cards




2711P-RCH CompactFlash to PCMCIA adapter


Cat. No.(1)


Terminal ModelInput Type


2711P-RGK4 400 Grayscale

2711P-RGB4 400 Color

2711P-RGT6 600 Grayscale or Color

2711P-RGT10 1000 Color

Table 30 - Backlight Replacement

Cat. No. Description Number of Backlights

2711P-RL10C2 Replacement color backlight for the 1000 series B/C displays 1

Table 31 - Bezel Replacement


2711P-RBT10 Replacement bezel for the 1000 touch terminal


Cat. No. Terminal Model Description Quantity

2711P-RTFC 400 and 600 Mounting levers 8

2711P-RTMC 1000 Mounting clips 8


Cat. No. Terminal Model Description Quantity

2711P-TBDC 400 and 600 DC power terminal block 10

2711P-RTBDC2 700 to 1500 2-pin DC power terminal block 10



Communication Cables The table provides a general list of cables used by the PanelView Plus terminals. All PanelView Plus terminals use a standard Ethernet cable for application transfers between a computer and the terminal.

PanelView Plus Runtime CablesTables 3538 list required runtime cables for PanelView Plus 400/600 and PanelView Plus 6 (700, 1000, 1250, 1500) terminals.

Table 34 - Cables

Cat. No. Description Length

2711C-CBL-UU02(1)

(1) This cable is used only by PanelView Plus 6 terminals.

USB host to USB device programming cable 2 m (6.5 ft)

2711-NC13 RS-232 operating/program cable, 9-pin D-shell to 9-pin D-shell 5 m (16.4 ft)

2711-NC14 RS-232 operating/program cable, 9-pin D-shell to 9-pin D-shell 10 m (32.7 ft)

2711-NC17 Remote RS-232 cable assembly, 9-pin D-shell to 9-pin D-shell 3 m (10 ft)

2711-NC21 RS-232 operating cable, 9-pin D-shell to 8-pin mini DIN 5 m (16.4 ft)

2711-NC22 RS-232 operating cable, 9-pin D-shell to 8-pin mini DIN 15 m (49 ft)

1761-CBL-AS03DH-485 network cable, 6-pin Phoenix to RJ45

3 m (10 ft)

1761-CBL-AS09 9 m (30 ft)

2711P-CBL-EX04 Ethernet CAT5 crossover cable 4.3 m (14 ft)

Table 35 - Runtime Communication Cables: PanelView Plus Terminals to SLC Controllers

Protocol PanelView Plus Comm Port400, 600, 700, 1000, 1250, 1500SLC 500, 5/01, 5/02

CH1 RJ45 (DH-485)

SLC 5/03, 5/04, 5/05CH0 (9-pin RS-232)

(DF1 or DH-485)

SLC 5/03CH1 (RJ45)

(DH-485)SLC 5/04

CH1 (DH+)SLC 5/05

CH1 (ENET)

DF1 RS-232 (DF1) port (9-pin)PanelView Plus 400 to 15002711P-RN22C (for 400 and 600 only)

2711-NC13 (5 m/16 ft)2711-NC14 (10 m/32 ft)

DH-485

RS-232 (DH-485) port (9-pin)PanelView Plus 400 to 15002711P-RN22C (for 400 and 600 only)

Use AIC+ module(1761-NET-AIC) to

connect to port 1 or 2

2711-NC13 (5 m/16 ft)2711-NC14 (10 m/32 ft)

Use AIC+ Module(1761-NET-AIC) to


DH-485 portPanelView Plus 400 and 600Requires 2711P-RN3(1)

1747-C10 (2 m/6 ft) 1747-C11 (0.3 m/1 ft)1747-C20 (6 m/20 ft)

Use AIC+ module(1761-NET-AIC)

to connect to port 3

1747-C10 (2 m/6 ft) 1747-C11 (0.3 m/1 ft)1747-C20 (6 m/20 ft)

DH-485 portPanelView Plus 700 to 1500Requires 2711P-RN6, 2711P-RN6K

1761-CBL-AS03 (3 m/10 ft)

1761-CBL-AS09 (9 m/30 ft)



1761-CBL-AS03 (3 m/10 ft)

1761-CBL-AS09 (9 m/30 ft)

ControlNet

ControlNet portPanelView Plus 400 and 600Requires 2711P-RN15CPanelView Plus 700 to 1500Requires 2711P-RN15S, 2711P-RN15SK

EtherNet/IP EtherNet/IP portPanelView Plus 400 to 1500

Use 1761-NET-ENI modulewith Ethernet cable

1585J-M type cable or

2711P-CBL-EX04 (4 m/14 ft) (2)

DH+ DH+ portPanelView Plus 400 and 600Requires 2711P-RN8PanelView Plus 700 to 1500Requires 2711P-RN6, 2711P-RN6K

Shielded

twinaxialcable (1770-CD)

(1) For CE compliance, use the 1761-NET-AIC or 1747-AIC module for cable lengths longer than 30 m (98 ft).(2) EtherNet/IP direct connection from the terminal to an SLC 5/05 controller requires an Ethernet switch or the 2711P-CBL-EX04 crossover cable.



Table 36 - Runtime Communication Cables: PanelView Plus Terminals to PLC-5 and MicroLogix Controllers

Protocol PanelView Plus Comm Port400, 600, 700, 1000, 1250, 1500PLC-5, PLC-5C, PLC-5E

CH0 (25-pin RS-232)(DF1)

MicroLogix 1400, 1500LRPCH1/CH2 (9-pin RS-232)

(DF1 or DH-485)

MicroLogix 1000, 1100, 1200, 1400, 1500LSP

CH0 (8-pin Mini DIN)(DF1 or DH-485)

MicroLogix 1100, 1400 Ethernet


2711-NC13 (5 m/16 ft)2711-NC14 (10 m/32 ft)

(9-to-25 pin adapter required)

2711-NC13 (5 m/16 ft)2711-NC14 (10 m/32 ft)

2711-NC21 (5 m/16 ft)2711-NC22 (15 m/49 ft) (3)

DH-485


2711-NC13 (5 m/16 ft)2711-NC14 (10 m/32 ft)

2711-NC21 (5 m/16 ft)2711-NC22 (15 m/49 ft)

DH-485 portPanelView Plus 400 and 600Requires 2711P-RN3(1)PanelView Plus 700 to 1500Requires 2711P-RN6, 2711P-RN6K



ControlNet

ControlNet portPanelView Plus 400 and 600Requires 2711P-RN15CPanelView Plus 400 to 1500Requires 2711P-RN15S or 2711P-RN15SK

To PLC-5C with ControlNet cable

EtherNet/IPEtherNet/IP portPanelView Plus 400 to 1500

To PLC-5E with1585J-M type cable or

2711P- CBL-EX04 (4 m/14 ft) (2)Use 1761-NET-ENI module

with Ethernet cable1585J-M type cable or

2711P- CBL-EX04 (4 m/14 ft) (2)


Shielded twinaxial cable(1770-CD)

(1) For CE compliance, use the 1761-NET-AIC or 1747-AIC module for cable lengths longer than 30 m (98 ft).(2) For a direct connection between the terminal and the controller use the 2711P-CBL-EX04 crossover cable.(3) The AIC+ module is recommended for isolation purposes when the terminal and controller are not on same power supply.

Table 37 - Runtime Communication Cables: PanelView Plus Terminals to Logix Controllers

Protocol PanelView Plus Comm Port400, 600, 700, 1000, 1250, 1500ControlLogix

CH0 (9-pin RS-232)(DF1)

CompactLogixCH0 (9-pin RS-232)

(DF1 or DH-485)


2711-NC13 (5 m/16 ft)2711-NC14 (10 m/32 ft)2706-NC13 (3 m/10 ft)

DH-485


2711-NC13 (5 m/16 ft)2711-NC14 (10 m/32 ft)2706-NC13 (3 m/10 ft)

DH-485 portPanelView Plus 400 and 600Requires 2711P-RN3(1)PanelView Plus 700 to 1500Requires 2711P-RN6, 2711P-RN6K



ControlNet

ControlNet portPanelView Plus 400 and 600Requires 2711P-RN15CPanelView Plus 700 to 1500Requires 2711P-RN15S, 2711P-RN15SK

Use 1756-CNB module with ControlNet cable1769-L35CR, 1769-L32C, 1768-CNB, or 1768-CNBR

with ControlNet cable

EtherNet/IPEtherNet/IP portPanelView Plus 400 to 1500

Use 1756-EN2T or 1756-ENBT module with1585J-M type cable or

2711P- CBL-EX04 (4 m/14 ft)(2)

To 1769-L35E, 1769-L23E, 1769-L32E, or 1768-ENBT module with 1585J-M type cable

or 2711P- CBL-EX04 (4 m/14 ft)(2)


Use 1756-DHRIO module with

shielded twinaxial cable (1770-CD)

(1) For CE compliance, use the 1761-NET-AIC or 1747-AIC module for cable lengths longer than 30 m (98 ft).(2) For a direct connection between the terminal and controller, use the 2711P-CBL-EX04 crossover cable.



Table 38 - Runtime Communication Cables: PanelView Plus Terminals to Interface Modules

ProtocolPanelView Plus Comm Port

400, 600700, 1000, 1250, 1500

1747-AIC1761-NET-AIC 1771-NET-ENI

Port 1 (9-pin) Port 2(8-pin Mini DIN)Port 3

(DH-485)Port 2

(8-pin Mini DIN)

DF1 RS-232 port (9-pin)PanelView Plus 400 to 15002711P-RN22C (for 400 and 600)

2711-NC13 (5 m/16 ft)2711-NC14 (10 m/32 ft)

2711-NC21 (5 m/16 ft)2711-NC22 (15 m/49 ft)Null modem required

1761-CBL-AP00 (5 m)1761-CBL-PM02 (2 m)2711-CBL-PM05 (5 m)2711-CBL-PM10 (10 m)

DH-485

RS-232 port (9-pin)PanelView Plus 400 to 15002711P-RN22C (for 400 and 600)

2711-NC13 (5 m/16 ft)2711-NC14 (10 m/32 ft)2711-NC21 (5 m/16 ft)2711-NC22 (15 m/49 ft) Null modem required

DH-485 portPanelView Plus 400 and 600Requires 2711P-RN3(1)

1747-C10 (2 m/6ft) 1747-C11 (0.3 m/1 ft)1747-C20 (6 m/20 ft)

1761-CBL-AS03 (3 m/10 ft)1761-CBL-AS09 (9 m/30 ft)

to single AIC+

DH-485 portPanelView Plus 700 to 1500Requires 2711P-RN6 or 2711P-RN6K

Direct connection to single AIC with

Belden 9842 cable(2)

Direct connection to single AIC+ with

Belden 9842 cable(2)

(1) For CE compliance, use the 1761-NET-AIC or 1747-AIC module for cable lengths longer than 30 m (98 ft).(2) Use serial port on the PanelView Plus terminal with an AIC+ module for a DH-485 network solution.



PanelView Plus Compact Runtime Cables

Tables 3942 lists required cables for runtime communication between PanelView Plus Compact controllers and controllers.

Table 39 - Runtime Communication Cables: PanelView Plus Compact Terminals to SLC Controllers

Protocol PanelView Plus Compact400, 600, 1000 Comm PortSLC 500, 5/01, 5/02

CH1 RJ45 (DH-485)

SLC 5/03, 5/04, 5/05CH0 (9-pin RS-232)

(DF1 or DH-485)

SLC 5/03CH1 (RJ45)

(DH-485)SLC 5/04

CH1 (DH+)SLC 5/05

CH1 (ENET)

DF1 RS-232 (DF1) Comm port (9-pin) 2711-NC13 (5 m/16 ft)2711-NC14 (10 m/32 ft)

DH-485 RS-232 (DH-485) Comm port (9-pin)Use AIC+ module(1761-NET-AIC) to


2711-NC13 (5 m/16 ft)2711-NC14 (10 m/32 ft)

Use AIC+ module(1761-NET-AIC) to


EtherNet/IP EtherNet/IP Comm port Use 1761-NET-ENI modulewith Ethernet cable

2711P- CBL-EX04 Ethernet crossover cable (1)

(1) An EtherNet/IP direction connection between a PanelView Plus Compact terminal and an SLC 5/05 requires hub or crossover cable listed.

Table 40 - Runtime Communication Cables: PanelView Plus Compact Terminals to MicroLogix Controllers

Protocol PanelView Plus Compact400, 600, 1000 Comm PortMicroLogix 1500LRPCH1 (9-pin RS-232)

(DF1 or DH-485)

MicroLogix 1000, 1200, 1500LSPCH0 (8-pin Mini DIN)

(DF1 or DH-485)MicroLogix 1100, 1400

Ethernet Port

DF1 RS-232 (DF1) Comm port (9-pin)2711-NC13 (5 m/16 ft)

2711-NC14 (10 m/32 ft)2711-NC21 (5 m/16 ft)

2711-NC22 (15 m/49 ft) (1)

DH-485 RS-232 (DH-485) Comm port (9-pin)2711-NC13 (5 m/16 ft)

2711-NC14 (10 m/32 ft)2711-NC21 (5 m/16 ft)

2711-NC22 (15 m/49 ft) (1)

EtherNet/IP EtherNet/IP Comm portUse 1761-NET-ENI module


2711P-CBL-EX04 cable (4 m/14 ft)(2)

(1) AIC+ Module recommended for isolation when PanelView and controller are not using same power supply.(2) For a direct connection between the terminal and controller, use the 2711P-CBL-EX04 crossover cable

Table 41 - Runtime Communication Cables: PanelView Plus Compact Terminals to Logix Controllers

Protocol PanelView Plus Compact400, 600, 1000 Comm PortControlLogix

CH0 (9-pin RS-232)(DF1)

CompactLogixCH0 (9-pin RS-232)

(DF1 or DH-485)

DF1 RS-232 (DF1) Comm port (9-pin)2711-NC13 (5 m/16 ft)

2711-NC14 (10 m/32 ft)

DH-485 RS-232 (DH-485) Comm port (9-pin) 2711-NC13 (5 m/16 ft)2711-NC14 (10 m/32 ft)

EtherNet/IP EtherNet/IP Comm portUse 1756-EN2T or 1756-ENBT module

with 1585J-M type cable or 2711P-CBL-EX04 cable (4 m/14 ft)(1)

To 1769-L35E, 1769-L23E, 1769-L32E with1585J-M type cable or

2711P-CBL-EX04 cable (4 m/14 ft)(1)

(1) For a direct connection between the terminal and controller, use the 2711P-CBL-EX04 crossover cable.

Table 42 - Runtime Communication Cables: PanelView Plus Compact Terminals to Network Modules

Protocol PanelView Plus Compact400, 600, 1000 Comm Port

1761-NET-AIC

Port 1 (9-pin) Port 28-pin Mini DINPort 3

(DH-485)

DF1 RS-232 Comm port (9-pin)2711-NC13 (5 m/16 ft)

2711-NC14 (10 m/32 ft)2711-NC21 (5 m/16 ft)

2711-NC22 (15 m/49 ft)

DH-485 RS-232 Comm port (9-pin)2711-NC13 (5 m/16 ft)

2711-NC14 (10 m/32 ft)

2711-NC21 (5 m/16 ft)2711-NC22 (15 m/49 ft)



PanelView Plus Migration Path

The PanelView Plus platforms provide a clear migration path for replacing older terminals. When migrating to a new platform, consider both the display size and the unit size. PanelView Plus terminals uses the same panel cutouts as existing PanelView products, yet offer a larger display. For instance, a PanelView Plus 6, 1250 terminal with a 12.1-inch display fits into the same cutout as a PanelView 1000 or 1000e with a 10.4-inch display. When choosing a terminal with the same display size, adapter plates are used to adapt the cutout of the new terminal.

Table 43 - PanelView Plus Replacement Terminals

PanelView Standard Terminal PanelView Plus Replacement Terminal Adapter Plate RequiredAdapter Plate Cat.

No.

PanelView Standard 300 or 300 Micro None available(1)

PanelView 550 or 600 touch PanelView Plus or PanelView Plus Compact 400 keypad or keypad/touchPanelView Plus or PanelView Plus Compact 600 touch No

PanelView 550 keypadPanelView 550 keypad/touch

PanelView Plus 600 keypad or keypad/touch No

PanelView Plus PanelView Plus Compact 400 keypad or keypad/touchPanelView Plus PanelView Plus Compact 600 touch Yes 2711P-RAK4

PanelView 600 keypadPanelView 600 keypad/touch

PanelView Plus 600 keypad or keypad/touch Yes 2711P-RAK6

PanelView Plus 6, 700 keypad or keypad/touch No

PanelView 900 keypadPanelView Plus 6, 700 keypad or keypad/touch Yes 2711P-RAK7


PanelView 900 touchPanelView Plus 6, 700 touch Yes 2711P-RAT7

PanelView Plus 6 or PanelView Plus Compact 1000 touch No

PanelView 1000 keypadPanelView Plus 6, 1000 keypad or keypad/touch Yes 2711P-RAK10


PanelView 1000 touchPanelView Plus 6 or PanelView Plus Compact 1000 touch Yes 2711P-RAT10

PanelView Plus 6, 1250 touch No

PanelView 1400 keypadPanelView Plus 6, 1250 keypad or keypad/touch Yes 2711P-RAK12S


PanelView1400e keypadPanelView Plus 6, 1500 keypad or keypad/touch(2) Yes 2711P-RAK15

None available

PanelView 1400 touch PanelView Plus 6, 1250 touch Yes 2711P-RAT12S

PanelView Plus 6, 1500 touch No

PanelView 1400e touchPanelView Plus 6,1500 touch(2) Yes 2711P-RAT15

None available

PanelView 1200, 1200e/1400e Keypad PanelView Plus 6,1250 keypad(2) Yes RAK12E

None available

PanelView 1200, 1200e Touch PanelView Plus 6,1250 touch(3) Yes RAT12E

None available

PanelView 1200/1200E touch PanelView Plus 6,1250 touch(3) Yes 2711P-RAT12E2

None available

(1) Replace the PanelView Standard 300 or 300 Micro with a PanelView Plus 400 keypad terminal by increasing the size of the current panel cutout.(2) Adapter plate required for stud-mounted terminals.(3) Requires modification of panel cutout.


PanelView Component Terminals www.klinkmann.com6 / 2011

PanelView Component Terminals

This component level operator interface provides a control and visualization solution for low-level applications by using serial or Ethernet communication. Preferred controllers are the Micrologix, SLC, and Micro800 controllers plus you can connect directly to component devices such as the PowerFlex 4 drives.

This platform offers a full line of 2- to 10-inch displays with touch or function key input. Plus, the integrated mounting clips on the terminal simplifies panel installation and maintenance. Other key features include the following:

Design software resident in the terminal means no additional software to install on your computer.

Secured programming access protects applications from unauthorized modifications.

Unicode language switching in languages such as Russian, Greek, Chinese, Japanese, and Korean.

Alarm messages with embedded variables and history. Recipe capability lets you upload and download groups of data or

parameter settings.

For complete technical specifications, certifications, and environmental specifications on the PanelView Component terminals, refer to the PanelView Component Specifications Technical Data, publication 2711C-TD001.

Software

The built-in programming software is accessed from a web browser over a USB or Ethernet connection. This means you can design your application and adjust terminal settings while viewing the results directly on the connected terminal. For those times when a PanelView Component terminal is not available, you can still create an application by using the free emulator.

Typical Configuration

A PanelView Component terminal is typically connected to a MicroLogix controller or another component, such as a PowerFlex 4 drive, over an Ethernet or serial connection.

Ethernet or Serial Connection


http://literature.rockwellautomation.com/idc/groups/literature/documents/td/2711c-td001_-en-p.pdf

PanelView Component Terminalswww.klinkmann.com6 / 2011

Product Selections

Product Accessories

Tables 4548 list accessories for the PanelView Component terminals.

BulletinNumber Input Type Display Size Display Type

| | |

2711C- F = Function keys 2 = 2 in. C = Color

K= Keypad and function keys 3 = 3 in. M = Grayscale

T = Touch screen 6 = 6 in. T = TFT Color

10 = 10 in.

Table 44 - PanelView Component Terminals

Cat. NoDisplay

Input TypeCommunication

Power Size Type Serial(1) Ethernet

C200 Model

2711C-F2M2-in. Monochrome STN display

4 function keys 24V DC

2711C-K2M 10 function keys and numeric keypad 24V DC

C300 Model

2711C-T3M3-in. Monochrome FSTN display

Touch screen 24V DC

2711C-K3M 10 function keys and numeric keypad 24V DC

C600 Model

2711C-T6M

6 in.

Monochrome FSTN display Touch screen 24V DC

2711C-T6C Color CSTN display Touch screen 24V DC

2711C-T6T Color TFT display Touch screen 24V DC

C1000 Model

2711C-T10C 10 in. Color TFT display Touch screen 24V DC

(1) Serial refers to RS-232 (DF1), RS-232 (DH-485), RS-485 communication.


Cat. No.(1)


PanelView Component Model

Input Type

Function Key Numeric Keypad Touch

2711C-RG2F C200

C300

2711C-RG2K C200

C300

2711C-RG6T C600

2711C-RG10T C1000


PanelView Component Terminals www.klinkmann.com6 / 2011

Communication Cables

This table summarizes cables used by the PanelView Component terminals.

Table 46 - Memory Cards


2711C-RCSD USB to Secure Digital (SD) adapter for SD card



2711C-RJ422 RS-422/RS-485 connector with resistor 10

2711-TBDC DC power terminal block 10

Table 48 - Power Supply


2711P-RSACDIN DIN-rail mount AC-to-DC power supply, 85265V AC, 4763 Hz 1

Table 49 - Cables and Adapters

Cat. No. Description Connectors Length

2711C-CBL-UU02 USB host to USB device programming cable. 2 m (6.5 ft)

2711C-CBL-AB03 RS-485 (5-pin) to RJ45 operating/programming cable for connecting PanelView Component terminals to SLC 5/01, 5/02, 5/03 controllers.

RS-485 (5-pin) to RJ45

1747-CP3 Operating/programming cable for connecting PanelView Component terminals to SLC and MicroLogix controllers.

9-pin D-shell to 9-pin D-shell null modem cable

3 m (10 ft)

1761-CBL-PM02 RS-232 operating/programming cable for connecting PanelView Component terminals to MicroLogix controllers.

9-pin D-shell to 8-pin mini DIN 2 m (6.5 ft)

2711-CBL-PM05 RS-232 operating/programming cable for connecting PanelView Component terminals to MicroLogix controllers. 9-pin D-shell to 8-pin mini DIN

5 m (16.4 ft)

2711-CBL-PM10 RS-232 operating/programming cable for connecting PanelView Component terminals to MicroLogix controllers. 9-pin D-shell to 8-pin mini DIN

10 m (32.7 ft)

2711P-CBL-EX04 Ethernet CAT5 crossover cable for use with PanelView Component C600 and C1000 terminals. RJ45 to RJ45

4.3 m (14 ft)

1761-NET-AIC AIC+ advanced interface converter, RS-232/RS-485.


PanelView Component Terminalswww.klinkmann.com6 / 2011

Tables 5053 lists required cables for runtime communication between the PanelView Component terminals and controllers.

Table 50 - Runtime Communication Cables: PanelView Component Terminals to SLC Controllers

Protocol PanelView Component Comm PortSLC-500, 5/01, 5/02

CH1 RJ45 (DH-485)

SLC-5/03, 5/04, 5/05CH0 (9-pin RS-232)

(DF1 or DH-485)

SLC 5/03CH1 (RJ45)

(DH-485)SLC 5/04

CH1 (DH+)SLC 5/05

CH1 (ENET)

DF1 RS-232 (DF1) port (9-pin) 1747-CP3 (3 m/10 ft)

DH-485RS-232 (DH-485) port (9-pin)


connect to port 1 or 21747-CP3 (3 m/10 ft)



RS-485 (DH-485) port (5-pin) 2711C-CBL-AB03(1) 2711C-CBL-AB03(1)

EtherNet/IP EtherNet/IP port Use 1761-NET-ENI module

with Ethernet cable

1585J-M type cable or 2711P- CBL-EX04

(4 m/14 ft) (2)

(1) The AIC+ module is recommended for isolation purposes when the terminal and controller are not on the same power supply.(2) For a direct connection between the terminal and controller, use the 2711P-CBL-EX04 crossover cable.

Table 51 - Runtime Cables: PanelView Component Terminals to MicroLogix Controllers

Protocol PanelView Component Comm PortMicroLogix 1400, 1500LRP

CH1/CH2 (9-pin RS-232)(DF1 or DH-485)

MicroLogix 1000, 1100, 1200, 1400, 1500LSPCH0 (8-pin Mini DIN)

(DF1 or DH-485)MicroLogix 1100, 1400

Ethernet

DF1 RS-232 (DF1) port (9-pin) 1747-CP3 (3 m/10 ft)1761-CBL-PM02 (2 m/6.5 ft)2711-CBL-PM05 (5 m/16 ft)

2711-CBL-PM10 (10 m/12 ft) (1)

DH-485 RS-232 (DH-485) port (9-pin) 1747-CP3 (3 m/10 ft)1761-CBL-PM02 (2 m/6.5 ft)2711-CBL-PM05 (5 m/16 ft)

2711-CBL-PM10 (10 m/12 ft) (1)

EtherNet/IP EtherNet/IP PortUse 1761-NET-ENI module


2711P- CBL-EX04 (4 m/14 ft) (2)

(1) The AIC+ module is recommended for isolation purposes when the terminal and controller are not on same power supply.(2) For a direct connection between the terminal and controller, use the 2711P-CBL-EX04 crossover cable.

Table 52 - Runtime Cables: PanelView Component Terminals to CompactLogix Controllers

Protocol PanelView Component Comm PortCompactLogix

CH0 (9-pin RS-232)(DF1 or DH-485)

DF1 RS-232 (DF1) port (9-pin)2711-NC13 (5 m/16 ft)

2711-NC14 (10 m/32 ft)

DH-485 RS-232 (DH-485) port (9-pin)2711-NC13 (5 m/16 ft)

2711-NC14 (10 m/32 ft)

EtherNet/IP EtherNet/IP port 1585J-M type cable or 2711P- CBL-EX04 (4 m/14 ft) (1)

(1) For a direct connection between the terminal and controller, use the 2711P-CBL-EX04 crossover cable.

Table 53 - Runtime Cables: PanelView Component Terminals to Interface Modules

ProtocolPanelView Plus

Comm Port1761-NET-AICPort 1 (9-pin)

1761-NET-AICPort 2 (8-pin Mini DIN()

1761-NET-AICPort 3 (DH-485)

DF1 RS-232 port (9-pin) 1747-CP3 (3 m/10 ft)1761-CBL-PM02 (2 m/6.5 ft)2711-CBL-PM05 (5 m/16 ft)

2711-CBL-PM10 (10 m/12 ft)

DH-485 RS-232 port (9-pin) 1747-CP3 (3 m/10 ft)1761-CBL-PM02 (2 m/6.5 ft)2711-CBL-PM05 (5 m/16 ft)

2711-CBL-PM10 (10 m/12 ft)


Industrial Computers and Monitors www.klinkmann.com6 / 2011

Industrial Computers and Monitors

The industrial computers and monitors are built with high-grade components that are critical to the safety and success of applications in demanding industrial environments:

Seamless integration with the full suite of Rockwell Software solutions, including the Integrated Architecture platform and FactoryTalk View software

Utilities for system backup and restore, hardware analysis, and troubleshooting

Unit-level immediate exchange program to reduce downtime

Figure 5 - Selecting an Industrial Computer

Hazardous Location Computer

See page 39

Integrated Display Computers with Keypad

See page 37

Compact Non-display Computers

See page 43

See page 45

c-UL-us certified computer for hazardous locations?

-2070 C (-4158 F) temperature rating?

Do you need:

Computer with an integrated display?

Panel mount device?

Do you need:

Yes

No

Yes

No

Computer without a display or keypad?

Optional external monitor?

Do you need:

Yes

No

Integrated display and a keypad?

Do you need:

Yes

No

Integrated Display Computers

Small form factor?SSD or HHD?Temperature rating to

55 C (131 F)?AC or DC power?

Do you need:

Yes

Non-display Computers

No

See page 40

See page 32

Industrial Monitors For complete technical specifications, certifications, and environmental specifications on the industrial computers and monitors, refer to the Industrial Computers and Monitors Specifications Technical Data, publication IC-TD001.


http://literature.rockwellautomation.com/idc/groups/literature/documents/td/IC-td001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/td/ic-td001_-en-p.pdf

Industrial Computers and Monitorswww.klinkmann.com6 / 2011

Typical Configurations This configuration illustrates a typical station-level HMI showing a FactoryTalk View ME or FactoryTalk View SE local network with either PanelView Plus terminals, industrial computers and monitors, and a logix controller.

Figure 6 - FactoryTalk View Station Level HMI

This configuration provides a typical site-level HMI showing a FactoryTalk View SE network with industrial computers and monitors and a logix controller.

Figure 7 - FactoryTalk View Site Level HMI

Clients(Industrial computers and monitors)

HMI Servers

Primary Data Server

Secondary Data Server

FactoryTalk Directory Server

Logix Controller



Integrated Display Computers

When you require a window into your operations, the integrated display computers serve as the foundation for visualization control of processes and machinery by using information displays to repair, maintain, or start a process.

This platform is available with a continuous-duty, hard-disk drive or a mission-critical, solid-state drive that is free of moving parts. A fanless design with increased temperature ratings and low-voltage processors add to the ruggedness of this computer. Plus, you can choose a standard or performance package to get just the computing power you need.

The integrated display computers provide seamless integration with the full suite of Rockwell Software solutions, including the Integrated Architecture platform and FactoryTalk View software.

Performance Models

Performance models are equipped with features designed to meet the most demanding integrated display computer needs:

Hard-disk drive or solid-state drive with DC power input option 12-, 15-, or 17-inch display options Lockable front-accessible USB 2.0 port Core Duo processor and expandable memory up to 4 GB Expansion options through a PCI slot and an accessory kit for adding PCI

express or additional PCI Two CompactFlash slots Rated to 55 C (131 F) for 12- and 15-inch displays and 50 C (122 F)

for 17-inch displays Flush panel design minimizes debris buildup

Standard Models

Standard models provide the essential features you need at the right value for most visual interface and basic information applications.

Hard-disk drive or solid-state drive with DC power input option 12-, 15-, or 17-inch display options Celeron M processor with expandable memory to 4 GB One CompactFlash slot Rated to 50 C f(122 F) for all displays



Product Selections

0

BulletinNumber

Display Size

InputType Package Operating System Power Bezel Type

| | | | | | |

6181P- 2 = no display N = No touch S = Standard XP= Windows XP Professional forEmbedded Systems

Default = AC Default = Aluminum

HDD drive 12 = 12.1 in. T = Touch screen P = Performance D = DC SS = Stainless steel

15 = 15 in.

17 = 17 in.

Table 54 - 6181P Integrated Display Computers with Hard Disk Drives (HDD)

Cat. No. Display Size ResistiveTouch Screen Package Operating System Power Bezel

1200P Model

6181P-12NSXP

12.1-in. TFT display

Standard

Windows XP Professional for Embedded Systems

AC Aluminum

6181P-12NPXP Performance AC

6181P-12TSXP Standard AC

6181P-12TPXP Performance AC

6181P-12TPXPDC Performance DC

6181P-2PXP No display Performance Windows XP Professional for Embedded Systems

AC

6181P-2PXPDC Performance DC

1500P Model

6181P-15NSXP 15-in. TFT display Standard


AC Aluminum





6181P-15TPXPSS Performance AC Stainless steel

1700P Model

6181P-17NSXP 17-in. TFT display Standard Windows XP Professional for Embedded Systems

AC Aluminum





6181P-17TPXPSS Performance AC Stainless steel

Table 55 - Package Features: 6181P Integrated Display Computers with HDD

Package Features Standard Performance

Processor Intel Celeron 1.06 Hz Core Duo 1.2 GHz

RAM 2 GB DDR2 (4 GB max) 4 GB DDR2 (4 GB max)

Hard disk drive 40 GB, 2.5-in. SATA HDD 40 GB, 2.5-in. SATA HDD

Optical storage DVD-RW/CD-RW

Expansion slots 1 half-length PCI (upgradable to 2 PCI or 1 PCI + 1 PCI Express)

2 half-length PCI (upgradable to1 PCI + 1 PCI Express)



BulletinNumber

Display Size

InputType Package Operating System Power Bezel Type

| | | | | | |

6181F-

SSD drive

12 = 12.1 in. N = No touch S = Standard XP= Windows XP Professional forEmbedded Systems

Default = AC Default = Aluminum

15 = 15 in. T = Touch screen P = Performance D = DC SS = Stainless steel

17 = 17 in.

Table 56 - 6181F Integrated Display Computers with Solid-state Drives (SDD)

Cat. No. Display Size ResistiveTouch Screen Package Operating System Power Bezel

1200P Model

6181F-12TSXP 12.1-in. TFT display Standard Windows XP Professional for Embedded Systems

AC Aluminum


6181F-12TPXPDC Performance DC

6181F-12TSWE Standard Windows Embedded Standard 2009

AC Aluminum

6181F-12TPWE Performance AC

6181F-12TPWEDC Performance DC

1500 Model

6181F-15TSXP 15-in. TFT display Standard


AC Aluminum

6181F-15TPXP Performance AC

6181F-15TPXPDC Performance DC

6181F-15TPXPSS Performance AC Stainless steel


AC Aluminum



6181F-15TPWESS Performance AC Stainless steel

1700P Model

6181F-17TSXP 17-in. TFT display Standard Windows XP Professional for Embedded Systems

AC Aluminum

6181F-17TPXP Performance AC

6181F-17TPXPDC Performance AC

6181F-17TPXPSS Performance AC Stainless steel


AC Aluminum



6181F-17TPWESS Performance AC Stainless steel

Table 57 - Package Features: 6181P Integrated Display Computers with SSD


Processor Intel Celeron 1.06 Hz Core Duo 1.2 GHz

RAM 2 GB DDR2 (4 GB max) 4 GB DDR2 (4 GB max)

Storage drive 16 GB CompactFlash solid-state drive

16 GB CompactFlash solid-state drive

Optical storage DVD-RW/CD-RW

Expansion slots 2 half-length PCI (upgradable to 2 PCI or 1 PCI + 1 PCI Express)

1half-length PCI (upgradable to1 PCI + 1 PCI Express)



Accessories

Tables 5866 list accessories for the 6181P/6181F integrated display computers.6

Table 58 - Storage Drives

Cat. No. Description For Use With

6189V-25HDD 2.5-in. hard-disk drive standard 6181P series B, C, D

6189V-25HDDST40 2.5-in. 40 GB SATA hard disk drive 6181P series E

6189V-25SSD8GB 2.5-in. IDE 8 GB solid-state drive 6181F series B, C, D

6189V-CFSSD8GB CompactFlash IDE 8 GB solid-state drive 6181P/6181F series E

6189V-CFSSD16GB CompactFlash IDE 16 GB solid-state drive 6181P/6181F series E

Table 59 - Memory Modules


6189V-1GDDR2 1 GB DDR2 memory 6181P/F series E

6189V-2GDDR2 2 GB DDR2 memory 6181P/F series E

Table 60 - Add-in Cards and Modules


6189V-2PCI15 PCI expansion slot kit provides 2 PCI slots 6181F-156181P-15 series B and C

6189V-2PCI15R PCI expansion slot kit provides 2 PCI slots 6181F-15 series D6181P-15 series D

6189V-COMMCARD RS-232 serial PCI communication card 6181P/F

6189V-PCIENET Ethernet PCI card, 10/100/1000 Mbps 6181P/F

6189V-PCIDVI PCI AGP/DVI video card, dual outputs 6181P/F

6189V-EXTPCIS PCI expansion slot kit 6181P/F series E (performance)

Table 61 - Power Supply


6189V-ACPS External power supply, 100240V AC, 65 W ATX

6181P/F series E (standard)

Table 62 - Protective Screen Covers

Cat. No. Description Quantity For Use With

6189V-SCRNCOVER12 Protective screen cover 10 6181F-12, 6181P-12



6189V-15PCOVER 15-in. vinyl bezel cover 1 6181F-15, 6181P-15





6189V-MCLPS3 Mounting clips 14 6181P/6181F series E

Table 64 - Cables


6189V-DVICBL2 Digital video cable, 2 m (6.5 ft) 6181P/F series E (performance)

6189V-DVICBL5 Digital video cable, 5 m (16.4 ft) 6181P/F series E (performance)

2711-NC13 Touch screen cable, 5 m (16.4 ft) 6181P

Table 65 - Replacement Key


6189V-USBKEY Key for USB/power switch 6181P/F series E (performance)

Table 66 - Industrial Keyboards and Pointing Devices

Cat. No. Description Material Buttons/Keys

6189V-HPMOUSE PS/2 desktop mouse

Stainless Steel

3-button

6189V-HPMOUSEP PS/2 panel-mount mouse 3-button

6189V-KBDEPS1 PS/2 desktop keyboard/mouse 116

6189V-KBPEPS1 PS/2 panel-mount keyboard/mouse 116

6189V-KBDEPU1 PS/2 desktop keyboard/mouse Polycarbonate 84

6189V-KBDEPU1U USB desktop keyboard/mouse 84

6189V-KBDEPC1U USB desktop keyboard/mouse 116



Integrated Display Computers with Keypad

With an integral display and keypad in the same unit, this platform can function as an operator input station or an industrial computer. The absence of external monitor cables and separate component mounting requirements makes for easy system integration. These panel-mount computers can control machinery or a process, display information necessary to repair, maintain, or start up a process; and gather basic production information for making informed business decisions:

12- or 15-inch flat panel displays with a resistive touch-screen option 36 or 44 configurable keys and alphanumeric keypad Lockable front-accessible USB port and power switch Two hot-swappable hard-disk drive bays, RAID capable Two full-length PCI, half-length PCI, and full-length ISA expansion slots Standard package or performance package equipped with higher

processing power, and RAM and a DVD-RW drive

Product Selections

Bulletin Number Display Size Input Type Package Operating System Power

| | | | | |

6180P- 12 = 12.1 in. K = Keypad S = Standard XP= Windows XP Professional Default = AC

15 = 15 in. B = Key & Touch P = Performance D = DC

Table 67 - Integrated Display Computer with Keypad

Cat. No. Display Size ResistiveTouch Screen Function

Keys Package Operating System Power

1200P Model

6180P-12KSXP 12.1-in. TFT Display 36 Standard

Windows XP Professional

AC

6180P-12KPXP 36 Performance AC

6180P-12BSXP 36 Standard AC

6180P-12BPXP 36 Performance AC

6180P-12BPXPDC 36 Performance DC

1500P Model

6180P-15KSXP 15.1-in. TFT Display 44 Standard


AC

6180P-15KPXP 44 Performance AC

6180P-15BSXP 44 Standard AC

6180P-15BPXP 44 Performance AC

6180P-15BPXPDC 44 Performance DC

Table 68 - Package Features: Integrated Display Computer with Keypad


Processor Celeron M 1.86GHz Core Duo 1.66GHz

RAM 1 GB DDR2 2 GB DDR2

Floppy disk drive 3.5 in. 3.5 in.

Hard disk drive 160 GB 160 GB

Optical storage DVD-ROM/CD-RW DVD-RW



Accessories

Tables 6975 list accessories for the 6180P display computers with a keypad.



6189V-35HDDST160 3.5-in. 160 GB SATA hard disk drive standard

6180P

6189V-SLDUAL CD-RW/DVD-RW combo drive (slim) 6180P



6189V-1GDDR2 1 GB DDR2 memory 6180P

6189V-2GDDR2 2 GB DDR2 memory 6180P



6189V-COMMCARD RS-232 serial PCI communication card 6180P, 6180W

6189V-PCIENET Ethernet PCI card, 10/100/1000 Mbps 6180P, 6180W

6189V-PCIDVI PCI AGP/DVI video card, dual outputs 6180P, 6180W

6189V-RAIDSATA SATA RAID 0 and RAID 1 PCI card 6180P

Table 72 - Protective Screen Covers


6189V-SCRNCOVER12 Protective screen cover 10 6180W-12, 6180P-12

6189V-SCRNCOVER15 Protective screen cover 10 6180P-15, 6180W-15

Table 73 - Cables


2711-NC13 Touch screen cable, 5 m (16.4 ft) 6180P

Table 74 - Replacement Key


6189V-USBKEY Key for USB/power switch 6180P




Stainless steel

3-button









Hazardous Location Computers

This extreme environment computer combines intrinsic safety with market leading, extreme operating, temperature ratings. Industries from oil and gas to chemicals and mining must regularly work with potentially explosive materials, in locations where hardware often takes a beating. These computers are designed to endure the harsh extremes of heat and cold.

With Class 1 Division 2 hazardous location certification, the extreme environment computer can be safely used globally in areas where explosive materials may be present. The display version of this computer is panel mounted while the non-display version mounts on a wall. Both can withstand temperatures between -2070 C (-4158 F) inside a cabinet or enclosure. The surface temperature of the front of the display computer can withstand temperatures in the range -2055 C (-4131 F).

Product Selections

AccessoriesTables 7779 list accessories for the hazardous location computer.

Non-display VersionDisplay Version

Bulletin Number Display Size Package Operating System Input Power

| | | | |

6181X 12 = 12.1 in. P = Performance XP = Windows XP Professional for Embedded Systems DC = Standard

N = No display

Table 76 - Hazardous Location Computer

Cat. No. Display Size Processor RAM Storage DriveExpansion

Slots Operating System Power Mounting

1200XT Model

6181X-12PXPDC12.1-in. TFT display Resistive touch Sunlight readable

Core Duo U2500, 1.2GHz

2 GB (4 GB max)

8 GB CompactFlash(1)

1 half-length PCI


DC Panel

6181X-NPXPDC No display Core Duo U2500, 1.2GHz

2 GB (4 GB max)

8 GB CompactFlash(1)

1 half-length PCI


DC Wall

(1) Another CompactFlash Type 2 slot available.



6189X-4GDDR2 4 GB DDR2 memory



6189X-MCLPS Mounting clips 10



6189V-CFSSD16GB CompactFlash IDE 16 GB solid-state drive



Non-display Computers Whether applied in a control room environment or on the factory floor, the 6177R non-display computers provide the appropriate level of technology for a range of industrial applications. These non-display computers are available in various form factors, feature sets, and operating systems making it easier for you to choose the computer that best matches your industrial computing needs.

Product Selections

650R Model750R Model

1450R Model

Table 80 - Non-display Computers

Cat. No. Mounting Package Features Processor RAMHard Drive

Optical Storage

Expansion Slots Operating System Power

650R Model

6177R-M3PXP M3 Machine PerformanceCore 2 Duo

1.66GHz

1 GB 160 GBCD-RW/DVD-RW

2 half-length PCI1 full-length PCI or1 full-length ISA

Windows XP Professional AC

6177R-M3PXPDC M3 Machine Performance 1 GB 160 GB DC

6177R-M3AS3 M3 Machine Advanced 4 GB (2) 160 GB Windows Server 2003 R2 AC

750R Model

6177R-M4SXP M4 Machine Standard Celeron2.66 Ghz

1 GB 160 GBDVD-ROM/

CD-RW3 half-length PCI1 PCI Express x1


AC

6177R-M4PXP M4 Machine PerformancePentium 4 3.0 GHz

2 GB 160 GB AC

6177R-M4AXP M4 Machine Advanced 4 GB 160 GBDVD-RW

AC

6177R-M4AS3RD M4 Machine Server 4 GB (2) 160 GB Windows Server 2003 R2(1) AC

1450R Model

6177R-R4SXP 4U Rack Standard Celeron2.66 Ghz

1 GB 160 GB

DVD-ROM/CD-RW

6 half-length PCI1 PCI Express x1


AC

6177R-R4PXP 4U Rack Performance

Pentium 4 3.0 GHz

2 GB 160 GB 3 half-length PCI3 full-length PCI1 PCI Express x1

AC

6177R-R4LXP 4U Rack Legacy 2 GB 160 GB 3 half-length PCI2 full-length PCI2 full-length ISA1 PCI Express x1

AC

6177R-R4AS3RD 4U Rack Server 4 GB (2) 160 GB DVD-RW 6 half-length PCI1 PCI Express x1

Windows Server 2003 R2(1) AC

(1) Enabled for RAID 1 operation.



Process and Visualization Bundles

Specific models of the 6177R computer are configured as visualization servers or workstations for the PlantPAx Process Automation System. Each computer is prepackaged with specific hardware and software components.

For more information on the PlantPAx Process Automation System, go to http://rockwellautomation.com/solutions/process.

Accessories

Tables 8287 list accessories for the 6177R non-display computers.

Table 81 - Process and Visualization Bundles

Cat. No. Description Hardware Software

7477-IS2VS100 Visualization server on industrial hardened computer. Includes a FactoryTalk View SE server license for 100 displays

Cat. no. 6177R-M3AS3650R model

FactoryTalk Administration Console FactoryTalk Directory server FactoryTalk View SE server FactoryTalk View SE client FactoryTalk View Studio FactoryTalk Alarms and Events RSLinx Enterprise RSLinx Classic RSLinx Gateway Logix5000 clock tool FactoryTalk Activation server Rockwell Automation support tool

7477-IS2VS250 Visualization server on industrial hardened computer. Includes a FactoryTalk View SE server license for 250 displays

7477-IC2VC Visualization client workstation on industrially hardened computer. Includes a FactoryTalk View SE client license.

Cat. no. 6177R-M3PXP650R model

FactoryTalk View SE client FactoryTalk Alarms and Events FactoryTalk Batch client FactoryTalk eProcedure FactoryTalk Activation client Rockwell Automation support tool



6189V-35HDDST160 2.5-in. 160 GB SATA hard disk drive standard

6189V-SLDUAL CD-RW/DVD-RW combo drive (slim)



6189V-1GDDR2 1 GB DDR2 memory

6189V-2GDDR2 2 GB DDR2 memory


http://www.rockwellautomation.com/solutions/process/http://www.rockwellautomation.com/solutions/process/




6189V-COMMCARD RS-232 serial PCI communication card

6189V-PCIENET Ethernet PCI card, 10/100/1000 Mbps

6189V-PCIDVI PCI AGP/DVI video card, dual outputs

6189V-RAIDSATA SATA RAID 0 and RAID 1 PCI card



6189V-MCLPS2 Mounting clips 12

Table 86 - Cables


2711-NC13 Touch screen cable, 5 m (16.4 ft)




Stainless Steel

3-button









Compact Non-display Computer

These fanless computers provide an extremely durable computer option for harsh environments and require less space than most computers. Designed without cooling fans, the 6155F/6155R non-display computers come with either a mission critical solid-state drive or a continuous-duty hard-disk drive. Combine these features with the Windows Embedded Standard 2009 or Windows XP Professional operating system and you have the ideal platform for running visualization, control, or maintenance applications.

Product SelectionsBulletin Number Display Package Operating System Input Power

| | | | |

6155R HDD (hard-disk drive)

or6155F

SDD (solid-state drive)

N = No display S = Standard XP = Windows XP Professional Default = AC power

P = Performance WE = Windows Embedded Server 2009 DC = DC power

Table 88 - Compact Non-Display Computers

Cat. No. DisplayStorage Drive Expansion

Slots Package Processor RAM Operating System Power SSD HDD

200R Model - Solid State Drive (SDD)

6155F-NPXP None 16 GB None Performance

Celeron M 1 GHz

2 GBWindows XP Professional

AC

6155F-NPXPDC 16 GB None Performance 2 GB DC

6155F-NPWE 16 GB None Performance 2 GB Windows Embedded Standard 2009

AC

6155F-NPWEDC 16 GB None Performance 2 GB DC

200R Model - Hard Disk Drive (HDD)

6155R-NSXP None 40 GB None StandardCeleron M

1 GHz

1 GB


AC

6155R-NPXP 40 GB None Performance 2 GB AC

6155R-NPXPDC 40 GB None Performance 2 GB DC

Table 89 - Package Features: Compact Non-display Computers

Package Features 6155R Standard 6155R/6155F Performance

I/O 1 serial port 1 Ethernet 10/100/1000 MBPS port 4 USB ports 1 VGA port 1 PS/2 mouse 1 PS/2 keyboard port

2 serial ports 2 Ethernet LAN port 4 USB ports 1 VGA 1 PS/2 mouse 1 PS/2 keyboard port



Accessories

Tables 9095 list accessories for the 6155R compact non-display computers.



6189V-25HDD 2.5-in. hard-disk drive standard 6155R-N

6189V-25HDDST40 2.5-in. 40 GB SATA hard-disk drive 6155R

6189V-25SSD8GB 2.5-in. IDE 8 GB solid-state drive 6155F


6155R/6155F series E


6155F series E



6189V-1GSODDR2 1 GB DDR2 SODIMM memory 6155R/6155F series E

6189V-2GSODDR2 2 GB DDR2 SODIMM memory 6155R/6155F series E

Table 92 - Add-in Cards and Modules for Legacy Non-Display Computers


6189V-COMMCARD RS-232 serial PCI communication card 6155R-7, 6155R-14

6189V-PCIENET Ethernet PCI card, 10/100/1000 Mbps 6155R-7, 6155R-14

6189V-PCIDVI PCI AGP/DVI video card, dual outputs 6155R-7, 6155R-14

Table 93 - Cables


2711-NC13 Touch screen cable, 5 m (16.4 ft) 6155R




Stainless steel

3-button







Table 95 - Replacement Battery


6189V-BATTERY Replacement battery 6155R series E



Industrial Monitors Whether your visualization application is on the factory floor or in a control room, the monitor portfolio provides versatile mounting configurations and interface options to choose from.

The industrial monitors deliver the latest in LCD technology for rugged industrial environments. Combine these monitors with any of the Rockwell Automation non-display computers to create a powerful visualization, maintenance, control, or information computing solution:

The performance monitors are ideal for special purpose environments such as Class 1 Division 2, and food & beverage areas, providing superior protection against heat, shock, and vibration. Combine with the 6181X hazardous location computer for a complete system solution.

The standard monitors are suited for less demanding environments but still able to maintain endurance to temperature, shock, and vibration.

Standard Monitor Selections

Bulletin Number Display Size Mounting Type(1)

(1) Panel-mount monitors have aluminum bezels. VESA mount monitors have plastic bezels.

Touch screen

| | | |

6176MStandard Monitors

15 = 15 in. P = Panel N = No touch screen

17 = 17 in. V = VESA T = Touch screen

19 = 19 in.

Table 96 - Standard Monitors

Cat. No. Display Size Mounting ResistiveTouchscreen Bezel Includes

1550M Model

6176M-15PN

15-in. TFT LCD display

Panel Aluminum

Cables and power supply

6176M-15PT Panel Aluminum

6176M-15VN VESA Plastic

6176M-15VT VESA Plastic

1750M Model

6176M-17PN


Panel Aluminum





1950M Model

6176M-19PN


Panel Aluminum





Performance Monitors

Standard Monitors



Performance Monitor SelectionsBulletin Number Display Size Mounting Type Touch Screen Bezel Type

| | | | |

6186MPerformance Monitors

12 = 12.1 in. P = Panel N = No touch screen Default = Aluminum

15 = 15 in. V = VESA T = Touch screen SS = Stainless steel

17 = 17 in.

19 = 19 in.

Table 97 - Performance Monitors

Cat. No.(1)

(1) All 6186M models are suitable for hazardous location environments.

Display Size ResistiveTouchscreen Bezel Includes

1200M Model

6186M-12PN 12.1-in. TFT

PanelView Plus Terminals

Documents

Transcript of PanelView Plus Terminals