PA SOR for Electrical Works

0

SCHEDULE OF RATES

1

SECTION X - STANDARD SCHEDULE OF RATES

GENERAL PREAMBLES 1. The clauses in the General Preambles shall apply to all work items contained in the Standard

Schedule of Rates. 2. All rates include the allowance for complying with the General Preambles and Specifications. 3. All rates contained in the Standard Schedule of Rates are exclusive of any Goods and Service Tax.

Any such Goods and Service Tax shall be borne by the Employer as and when the same becomes due and payable.

4. All works, materials and goods described in this Schedule of Rates shall be of the respective kinds

described in the Contract and shall conform to the Specifications, Public Utilities Board, Energy Market Authority and other relevant Statutory Requirements and to be approved by the Superintending Officer.

5. The description given for each item shall unless otherwise stated, be held to include the use of

materials, labour, transport, equipment, tools, mobile lifting work platform, boom lift, hacking, supply of fuel and all idle time, conveyance, delivery, unloading, storing, hoisting, stools/ladders, all labour for setting, fitting, fixing in position, connection, all cutting and waste, return of packings, establishment charges, overheads, profit and all forms of claim for loss and expenses, labour for preparing surface to receive work, dismantling, protecting materials and work, making good all affected works and disposal of fittings including checking, tracing and clearing of fault (if any) before installation and testing after installation.

6. All rates in the Schedule shall include all necessary stagings and scaffoldings (only applicable up to

6 metres high, any height above 6 metres shall be paid separately, measuring from ground level, i.e. from the base for which scaffolding rests) unless specified otherwise.

7. All rates in the Schedule shall be applicable for new and replacement works unless otherwise

stated. The rate for each item for the installation/fixing of parts/fittings shall unless otherwise stated, deemed to include all staples, clips, screws bolts, rawl plug ramset brackets and other fixing accessories necessary for the satisfactory completion of the installation works.

8. Unless otherwise stated, all works shall be measured nett as fixed in its place. 9. If there is any disagreement between the Employer and the Term Contractor on any of the items,

the Employer’s assessment shall be taken as final. 10. The term “as specified” means as specified in all Specifications, Works Order and/or drawings.

2

STANDARD SCHEDULE OF RATES

GENERAL PREAMBLES 11. The following abbreviations are used for the units : -

m - Linear metre m2 - Square metre

m3 - Cubic metre no. - Number

pt - Point set - Complete set

job - Per job pole - Per pole

test - Per test tube - Per tube

hr - Per Hour box - Per box

12. Where brand, trade names or catalogue numbers are given in the description, they are solely intended for fixing the rates of the Items. The products and materials to be used in the Contract shall be governed by the specifications, drawings, other documents forming the contract and/or subject to the approval of the Superintending Officer.

13. Daywork’s Schedule of Rates for LABOUR and PLANTS (Items U001 to U010) is inclusive of 15%

Establishment Charges and Profit. The contract percentages adjustment shall also apply. 14. For computation of ‘STAR’ rate using Daywork’s Schedule of Rates, the contract percentages

adjustment shall NOT apply to the ‘STAR’ rates computation. 15. In the case of claim under dayworks, the Contractor shall keep proper records of the names,

occupations and working hours of all workmen employed for such work and the quantities and descriptions of all materials and plant employed. Such records, receipts or vouchers must be verified by the Superintending Officer’s Representative before payment can be effected. Provided always if the Superintending Officer’s Representative shall consider that for any reason the keeping of such records, receipts and vouchers by the Contractor as required was impracticable, he shall nevertheless be entitled to authorize payment for such work either as daywork (on being satisfied as to the time employed and plant and materials used on such work) or at such value thereof as he shall consider fair and reasonable.

3

A LIGHTING AND FAN POINT

Contents SOR Page 1. Surface wiring for lighting and fan point in pvc A1

trunking 2. Surface wiring for lighting and fan point in Al — A2

metal conduit 3. Surface wiring for lighting and fan point in pvc A2 - A3

conduit 4. Surface wiring for public lighting point in pvc A3

trunking

SOR Page A1

1

Item Description Unit Rate ($)

A00l A002 A003 A004 A005 A006 A007 A008

A. LIGHTING AND FAN POINT LIGHTING/FAN POINTS WIRING IN PVC TRUNKING * Surface wiring of 2.5 mm2 PVC sheathed cables and 2.5mm2 PVC earth cable in PVC trunking including surface mounted white plate switch with pvc mounting box but excluding ceiling rose, light fitting, fan regulator and fan: *(A001 A007) One lighting or fan point controlled by a 1-gang switch ( trunking run not exceeding 8m) One lighting or fan point controlled by a 1-gang switch (trunking run exceeding 8m but not exceeding 12m) Two lighting or fan points controlled by a 2-gang switch (trunkinq run not exceeding 12m) Three lighting or fan points controlled by a 3-gang switch (trunking run not exceeding 18m) Each additional lighting or fan point in one loop switch circuit to items A001 to A004 ( trunking run not exceeding 5m ) Each additional lighting or fail point in one looping circuit to items A00l to A004 (trunking run exceeding 5m but not exceeding 10m) One lighting point or fan point controlled by a two 2-way switch (trunking run not exceeding 12m) LIGHT/FAN POINTS WIRING IN METAL CONDUIT * Surface wiring of 2 x 2.5mm2 PVC sheathed cables and 2.5mm2 PVC earth cable in 20mm diameter galvanized steel conduit including surface mounted metal clad plate switch with mounting box but excluding ceiling rose, fitting, fan regulator and fan: *(A008 A0l4) One lighting or fan point controlled by a 1-gang switch (conduit run not exceeding 8m)

No. No. No. No. No. No. No. No.

18.35 25.35 36.50 58.65 11.20 22.30 31.80 43.90

SOR Page A2

2


A009

A010

A011

A012

A013

A014

A015

A016

A017

A018

A019

One lighting or fan point controlled by a 1-gang switch (conduit run exceeding 8m but not exceeding 12m)

Two lighting or fan points controlled by a 2-gang switch (conduit run not exceeding 12m)

Three lighting or fan points controlled by a 3-gang switch (conduit run not exceeding 18m)

Each additional lighting point or fan point in one looping circuit to items A008 to A011 (conduit run not exceeding 5m)

Each additional lighting or fan point in one looping circuit to items A008 to A01l (conduit run exceeding 5m but not exceeding l0m)

:One lighting or fan point controlled by two 2-way switch (conduit run not exceeding 12m)

LIGHTING/FAN POINTS WIRING IN PVC CONDUIT

* Surface wiring of 2 x 2.5mm2 PVC sheathed cables and 2.Smrn2 PVC earth cable in 20mm diameter PVC conduit including surface mounted metal clad plate switch with mounting box but excluding ceiling rose, fitting, fan regulator and fan: *(A01 A021)

One lighting or fan point controlled by a 1-gang switch (conduit run not exceeding 8m)

One lighting or fan point controlled by a 1-gang switch (conduit run exceeding 8m but not exceeding l2m)

Two lighting or fan points controlled by a 2-gang switch (conduit run not exceeding 12m)

Three lighting or fan points controlled by a 3-gang switch (conduit run not exceeding 18m)

Each additional lighting point in one looping circuit to items A0l5 to A0l8 (conduit run not exceeding 5m)

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

57.50

64.60

98.05

22.30

42.50

71.45

25.40

32.70

40.50

63.30

9.50

SOR Page A3

3


A020

A021

A022

A023

A024

A025

A026

A027

Each additional lighting or fan point in one looping circuit to items A0l5 to A018 (conduit run exceeding 5m but not exceeding 10m)

One lighting or fan point controlled by two 2-way switch (conduit run not exceeding 12m)

PUBLIC LIGHTING POINTS WIRING IN PVC TRUNKING

Items A022 to A027 are for the installation of new public lighting points. The application of any combination of items A022 to A027 in a single works order shall not exceed a total of 30 nos. per building block. Lighting point exceeding 30 nos. per building block shall be built-up from other sections of the Schedule of Rates

* Surface wiring for one public lighting point comprising 3 x 2.5mm2 PVC sheathed cables in PVC trunking of the following trunking run (ceiling rose, mounting block and wiring in pipe conduit to be measured separately):- *(A022 A027)

Not exceeding 10m per point (applicable for not more than 5 nos. of lighting point per block)

Not exceeding 10m per point (applicable for between 6 to 10 nos. of lighting point per block)

Not exceeding 10m per point (applicable for between 11 to 15 nos. of lighting point per block)

Exceeding 10m but not exceeding l6m per point (applicable for more than 5 nos. of lighting point per block)

Exceeding 10m but not exceeding 16m per point (applicable for between 6 to 10 nos. of lighting point per block)

Exceeding 10m but not exceeding 16m per point (applicable for between 11 to 15 nos. of lighting point per block)

No.

No.

No

No.

No.

No.

No.

No.

18.90

52.70

21.55

21.10

20.85

34.00

33.55

33.30

1

B NOT IN USE

1

C NOT IN USE

1

D CONDUIT, TRUNKING AND CABLE TRAY

Contents SOR Page

1. Conduit Dl

2. PVC Trunking Dl

3. Metal Trunking D2 – D3

4. Cable Tray D3

5. Conduit Pipe for Road Crossing D3

6. PVC Flexible Conduit D4

SOR Page D1

1


D001

D002

D003

D004

D005

D006

D007

D008

D009

D010

D011

D012

D013

D. CONDUIT, TRUNKING & CABLE TRAY CONDUIT (Barton, Maruchi, Walsall, Burns)

* Galvanized steel conduit of the following diameter fixed to wall, or ceiling complete with spacer bar, saddle, inspection box/junction/bend/tee, elbow and joint accessories *(D00l D003)

20mm

25mm

32mm

* Super high impact heavy gauge PVC conduit of the following diameter fixed to wall or ceiling complete with spacer bar, saddle, inspection box, junction/bend/tee, elbow and joint accessories :- *(D004 D007)

20mm

25mm

32mm

38mm

PVC TRUNKING (Waller, Litaflex, Chung Shan) * Approved PVC trunking of the following size including fixing to wall or ceiling *(0008 D013)

40mm x 20mm single compartment

80mm x 32mm two compartments

100mm x 40mm three compartments

60mm x 20mm two compartments

32mm x 16mm single compartment

25mm x 12.5mm single compartment

m

m

m

m

m

m

m

m

m

m

m

m

m

3.70

4.40

5.90

1.50

1.70

2.40

4.80

2.10

4. 80

8.00

3.00

1.90

1.80

SOR Page D2

2


D014

D015

D016

D017

D018

D019

D020

D021

D022

D023

D024

D025

D026

D027

D028

D029

D030

D031

D032

D033

D034

METAL TRUNKING (Ekko, Sakiya, Li-Soon, Ega, EM Industries) * Electro-galvanized metal trunking finished in epoxy. paint complete with coupling, detachable cover, screws and joint accessories including fixing to walls or ceilings of the following size :- *(0014 0034)

1.2mm thick 50mm x 50mm





















m

m

m

m

m

m

m

m

m

m

m

m

m

m

m

m

m

m

m

m

m

8.50

10.10

11.25

10.40

11.60

13.00

16.10

14.50

13.00

15.90

17.60

19.50

23.75

18.55

19.80

20.30

24.20

21.45

23.40

25.30

26.90

SOR Page D3

3


D035

D036

D037

D038

D039

D040

D04l

D042

D043

D044

D045

D046

D047

D048

D049

D050

D051

* Electro galvanized steel detachable trunking cover finished with epoxy coating and fixed to existing trunking of the following size : *(D035 D042)

1.2mm thick, 50 x 25mm or 50 x 50mm

1.2mm thick, 75 x 50mm or 75 x 75mm

1.2mm thick, 100 x 25mm to 100mm

1.2mm thick, 125 x 50mm

1.2mm thick, 150 x 25mm to 150mm




CABLE TRAY

* Hot dipped galvanized perforated mild steel cable tray of the following size including hanger, support and fixing :- *(D043 D047)

150mm width, 1.0mm thick


300mm width. 1.6mm thick

450mm width, 1.6mm thick V


CONDUIT PIPIE FOR ROAD CROSSING * UPVC class “C” pipe of the following diameter for road crossing laid in trench (trench measured separately) :- *(D048 D051)

50mm

80mm

100mm

150mm

m

m

m

m

m

m

m

m

m

m

m

m

m

m

m

m

m

3.50

3.90

4.55

5.35

6.10

7.00

8.90

8.90

9.00

12.60

16.50

24.25

29.10

1.70

2.90

4.50

7.20

SOR Page D4

4


D052

D053

D054

PVC FLEXIBLE CONDUIT

* PVC flexible conduit of diameter :- *(0052 D054)

20mm

25mm

32mm

m

m

m

2.20

2.80

3.70

1

E SWITCH, SOCKET OUTLET-AND CONSUMER UNIT Contents SOR Page 1. Switch El 2. Isolator El — E2 3. Socket Outlet E2 4. Plug E2 5. Consumer Control Unit E3

SOR Page E

1

1

Item Description Unit Rate ($) E001 E002 E003 E004 E005 E006 E007 E008 E009 E010 E011 E012

E. SWITCH, SOCKET OUTLET AND CONSUMER UNIT SWITCH PVC mounting box for switch or socket outlet Cl gang or 2 gang) Metal mounting box for switch or socket outlet (1 gang or 2 gang) * 5 to 10 Amp white rocker plate switch for the following (MK, Delta, Crabtree, Tenby, Clipsal) *(Eo03 E006) 1-way or 2-way switch 2 gang switch 3 gang switch 4 gang switch 5 to 10 Amp metal clad switch 1 gang (MK, Delta, Clipsal, PDL) 5 to 10 Amp metal clad switch 2 gang or 4 gang (MK, Delta, Clipsal, PDL) 20 Amp DP water heater switch with pilot lamp Amp DP switch ISOLATOR * Metal Clad or weatherproof Isolator Switch of the following (MEM, SMB, S-Team, ABB, Hager) *(E011 E014) 20 Amp DP to 40 Amp DP 63 Amp DP

No. No. No. No. No. No. No. No. No. No. No. No.

0.95 1.45 5.40 6.70 8.30 12.60 10.30 13.20 15.50 12.80 87.30 137.45

SOR Page E

2

2

Item Description Unit Rate ($) E013 E014 E015 E016 E017 E018 E019 E020 E021 E022 E023 E024 E025

20 Amp TPN to 40 Amp TPN 63 Amp TPN to 100 Amp TPN SOCKET OUTLET * Switch socket-outlet of the following type :- (MK, Tenby, Delta, Crabtree, Clipsal) *(E015 E022) 13 Amp 13 Amp, 2 gang 13 Amp metal clad 13 Amp metal clad, 2 gang 13 Amp weatherproof 15 Amp weatherproof 15 Amp 15 Amp, metal clad FUSED PLUG 13 Amp 3 pin plug 15 Amp 3 pin plug 15 Amp 3 pin weatherproof plug

No. No. No. No. No. No. No. No. No. No. No. No. No.

64.00 145.20 6.50 12.30 8.90 15.60 77.60 97.00 11.00 12.20 4.30 7.20 33.95

SOR Page E

3

3

Item Description Unit Rate ($) E026 E027 E028 E029 E030 E031 E032 E033 E034 E035 E036 E037

CONSUMER CONTROL UNIT * Insulated consumer control unit complete with 40 or 63 Amp RCCB (30 to 100 MA) 32 Amp OP or 63 Amp OP isolator including:(AEB, Mem, Sunlight, SMB, S-Team) *(E026 E030) 4 x 5 to 2OAmp 6KA MCB 6 x 5 to 2OAmp 6KA MCB 8 x 5 to 2OAmp 6KA MCB 10 x 5 to 2OAmp 6KA MCB 12 x 5 to 2OAmp EKA MCB * Metal clad consumer control unit complete with 40 or 63Amp RCCB (30 to 100 MA), 32 Amp OP or 63 Amp OP isolator including:(ABB, Mem, Sunlight, F & G, SMB, S-Team) *(E03l E035) 4 x 5 to 2OAmp 6KA MCB 6 x 5 to 2OAmp 6KA MCB 8 x 5 to 2OAmp EKA MCB 1OxSto2OAmp6KAMCB 12X5t02OAmp6KAMCB Metal clad split load consumer unit with 32 or 63A Amp OP isolator 2 x 20A SP MCB, with 40 or 63Amp OP RCCB (30 to 100 MA) 6 x 5/20 Amp 6KA SP MCB (ABB Mem, Sunlight, SMB, S-Team) Metal clad split-load consumer control unit with 32 or 60 Amp OP isolator 3 x 20A sp MCB, 40 or 63 Amp OP RCCB (30 to 100 MA) with 7 x 5/20A 6KA sp MCB (AEB, Mem, Sunlight, SMB, S-Team)


155.20 169.75 184.30 242.50 271.60 184.30 194.00 203.70 242.50 261.90 194.00 232.80

1

F NOT IN USE

1

G NOT IN USE

2

H INDOOR LUMINAIRE/LIGHT FITTING Contents SOR Page 1. Removal of Existing Luminaire H1 2. Mounting Channel Fluorescent Luminaire H1 - H2 3. Weatherproof Fluorescent Luminaire H2 — H3 4. Recessed Light H3 — H4 5. Emergency Light H5 6. Power Pack for Emergency Light H5 7. Aircraft Navigation / Obstruction Lights H5 — H6 8. High -end Low Bay Lights H6 - H7 9. Branded Luminaire H7 — H22

SOR Page H1

1

Item Description Unit Rate ($) H001 H002 H003 H004 H005 H006 H007 H008 H009 H010 H011 H012 H013

H. INDOOR LUMINAIRE/LIGHT FITTING REMOVAL OF EXISTING LUMINAIRE Remove existing ceiling, column wall mounted or recessed luminaire including reinstatement and disposal off site (New luminaire to be measured separately) MOUNTING CHANNEL FLUORESCENT LUMINAIRE (Removal of existing luminaire to be measured separately) * The following mounting channel fluorescent luminaire in powder coated finish complete with low-loss ballast (max 6.5W), capacitor and warmwhite or daylight tube (Davis, Woolite, Philips, Eurotec) :- *(H002 H0l6) 1 x 18W or 1 x 36W 1 x 18W or 1 x 36W with EMA approved electronic ballast (Osram, Vossloh Schwabe, Tridonic-Atco, Ultro, Helvar) in-lieu of low loss ballast and capacitor 2xl8W 2 x 36W 1 x 18W with clear acrylic prismatic diffuser 2 x 18W with clear acrylic prismatic diffuser 1 x 36W with clear acrylic prismatic diffuser 2 x 36W with clear acrylic prismatic diffuser 1 x 18W with metal reflector 1 x 36W with metal reflector 2 x 36W with metal reflector 1 x 18W or 1 x 36W with wire guard

No. No. No. No. No. No. No. No. No. No. No. No. No.

5.00 18.20 35.45 30.00 33.10 26.00 33.00 27.50 36.10 26.50 28.00 37.00 34.90

SOR Page H2

2

Item Description Unit Rate ($) H014 H015 H016 H017 H018 H019 H020 H021

1 x 18W or 1 x 36W with internal metal reflector, clear acrylic prismatic diffuser and ABS end cap 1 x 18W with internal metal reflector clear acrylic prismatic diffuser, ABS end cap and approved electronic ballast (Osram, Vossloh Schwabe, Triolonic Atco, Ultrom Helvar) in-lieu of the low lost ballast) 1 x 36W with internal metal reflector clear acrylic prismatic diffuser, ABS end cap and approved electronic ballast (Osram, Vossloh Schwabe, Triolonic Atco, Ultro, Helvar) in-lieu of the low lost ballast * The following surface mounted fluorescent luminaire with diffuser, low loss ballast warm white or day light tube (ITT-Reiss, Siemens 5LG225, Disalens 602, Thorlux Jubilee, Thorn Diffuserpack, Philips GBS314/TCS114) *(H017) H020) 1 x 18W 2 x 18W 1 x 36W 2 x 36W WEATHERPROOF FLUORESCENT LIGHT (Removal of existing luminaire to be measured separately) * The following weatherproof 1P65 fluorescent luminaire with low-loss ballast (max 6.5W) , capacitor, polycarbonate diffuser, warmwhite or daylight tube and plastic or stainless steel clip for the following :- (Thorlux, Siml4te, Philips, Woolite, Eurolite) *(H021 H023) 1 x 18W


29.70 42.00 46.00 40.00 58.00 45.00 70.00 51.40

SOR Page H3

3

Item Description Unit Rate ($) H022 H023 H024 H025 H026 H027 H028 H029 H030 H031 H032 H033 H034 H035 H036

1 x 36W 2 x 36W * The following weatherproof fluorescent fitting 1P65, with low loss ballast, warm white or daylight tube (Thorn LUES, ITT-Reiss, Disano Hydro 971) :- *(H024 H027) 1 x 18W 2 x 18W 1 x 36W 2 x 36W RECESSED LIGHT (Removal of existing luminaire to be measured separately) * Recessed T-bar mounted hinged frame fluorescent fitting with K12 / K15 prismatics diffuser or glossy mirror louvre matt ripped cross blade, double parabolic glossy mirror louvre, with low lost ballast, capacitor and warmwhite/daylight tube (Simlite, Trimex, Davis, Woolite) *(H028 H036) 1 x 36W (300mm x 1200mm) 2 x 36W (300mm x 1200mm) 2 x 18W (300mm x 600mm) 2 x 18W (600mm x 600mm) 3 x 4SW (600mm x 600mm) 4 x 18W (600mm x 600mm) 2 x 36W (600mm x 1200mm) 3 x 36W (600mm x 1200mm) 4 x 36W (600mm x 1200mm)

No. No. No. No. No. No. No. No. No. No. No. No. No. No. No.

60.30 89.30 105.00 120.00 115.00 135.00 83.20 94.20 79.50 82.50 99.50 115.20 118.50 137.20 158.80

SOR Page H4

4

Item Description Unit Rate ($) H037 H038 H039 H040 H041 H042 H043 H044 H045 H046 H047 H048

“THORLUX” RADIANCE 2 x 36W Cat 1 recessed mounted fluorescent luminaire “THORLUX” RADIANCE 4 x 18W Cat 1 recessed mounted fluorescent luminaire Extra over item H028 to”H038 for using each no. of electronic ballast in-lieu of low loss ballast (Osram, Vosslon-schwabe, Tridonic-Atco, Helvar, Ultro or other approved) MARCID (37226 & 00642) recessed downlight with die-cast aluminium ring, polished aluminium reflector, sand-blasted glass diffuser and 2 x 18W PLC lamps “INTERLUX” SS87213 recessed downlight silver reflector and protection glass with 2 x PLC 13W lamp & ballast “ILLTJMA” 080 recessed downlight with 0842 fresnel lens, SOW lamp and remote transformer “INNOLUX” RDVC 1013 recessed powder coated aluminium downlight with 13W PLC and aluminium reflector “INNOLUX” RDVC 1018 recessed downlight with aluminium rim, anodised aluminium reflector and 18W PLC lamp “EUROTEC” RAPID 2l4-83N0 2 x 18W PLC recessed downlight with metallized polycarbonate reflector, fresnel lens polycarbonate diffuser & integral electromagnetic ballast, 1P44 “DIL-CIKO” 17 recessed downlight ring diameter 185mm with 13W PLC lamp Recessed round or square flush mounted! eyeball halogen downlight in white, black or brass finish with remote transformer and lamp Square box light fitting 600mm x 600mm with 32W/40W circular tube (daylight or warm white)


380.00 390.00 16.00 238.00 75.00 140.00 61.10 77.60 65.00 105.75 45.00 37.85

SOR Page H5

5

Item Description Unit Rate ($) H049 H050 H051 H052 H053 H054 H055 H056 H057 H058 H059

EMERGENCY LIGHT (Removal of existing luminaire to be measured separately) * Emergency “Exit” light, recessed wall or ceiling mounted including Nickel Cadmium battery pack and PSB Batch Test Sticker (Maxspid, PNE, Denko, Simlite, Econlite) *(H049 H055) Single or Double-sided box type with 8W fluorescent tube Double-sided slim type using LED in lieu of fluorescent tube Single-sided slim type using LED in lieu of fluorescent tube Emergency bulk head lighting with 2 x 8W tube and Nickel Cadmium battery pack (Maxspid, Simlite, Econhite, PNE, Samcom) Emergency lighting Bulkhead with 10W tube Recessed self contained UFO emergency lighting with 1 x 10W halogen lamp and 2 hour battery pack (Maxspid, Simlite, Econlite, PNE) “PIILIPS” FGC Security lighting including PL 9W/llW lamp POWER PACK FOR EMERGENCY LIGHT Power pack for PL/PLC lamp Power pack for 18W to 36W fluorescent fitting AIRCRAFT NAVIGATION/OBSTRUCTION LIGHTS (Removal of existing luminaire to be measured separately) “FABRIKANT” 8003 twin obstruction light, lighting control box and change over relay with bracket and 42mm dia. hot dipped galvanised steel pipe mounted on roof deck and secured by 3 Nos. stainless steel cable support “HUBBELL” navigation obstruction light No. 700.35 cat no. BYMB-36002-AHQ with 2 x 7AP53-R, red frenel lens, transfer relay, 2 x 100W lamp and mounted on navigation obstruction lightmast

No. No. No. No. No. No. No. No. No. Set No.

83.30 130.00 115.00 116.40 140.00 116.40 129.60 87.30 92.15 1164.00 700.35

SOR Page H6

6

H060 H061 H062 H063 H064 H065 H066 H067 H068 H069 H070 H071 H072 H073

“THORN” F2l Single Obstruction Light with red lens cover and lamp “THORN” F22 Twin Obstruction Light with change over relay and lamps “THORN” OBSTA STI Omni-diectiona1 red low intensity obstruction light with neon discharge tube (Photometry : more than 32 cd) “THORN” OBSTA HI-STI Omni-directional red low intensity obstruction light with neon discharge tube (Photometry more than 32 cd) “BTI” L860 Series low Intensity red LEDs Obstruction Light “HONEYWELL” H&P 0B20 Single Obstruction Light with red lens cover and lamp “HONEYWELL” H&P 0B22 Twin Obstruction Lights with change over relay and lamps “WE-EF” 308-E2-100 Twin obstruction light with 8000hr Claude Krypton lamps, lighting control box, change over relay, brackets and 42mm dia. hot dipped galvanised steel pipe mounted on roof deck and secured by 3 nos. stainless steel cable support HIGH AND LOW BAY LIGHTS (Removal of existing luminaire to be measured seperately) * Highbay light fitting - recessed, suspended or ceiling mounted (Removal of existing luminaire to be measured seperately) (Thorn Hipak 2, Philips SDK/ HDK, Thorlux Combo, Siemens HS5O, Siteco Stylo) :- *(H068 H073) 250 - 400W Mercury, Open 250 - 400W Mercury, Enclosed 1P54 250 - 400W Mercury, Prismatic 250 - 400W SON/MBI, Open 250 - 400W SON/MBI, Enclosed 1P54 250 - 400W SON/MBI, Prismatic

No. No. No. No. No. No. No. Set No. No. No. No. No. No.

280.00 780.00 1050.00 1800.00 1800.00 320.00 880.00 1344.00 380.00 560.00 680.00 460.00 640.00 780.00

SOR Page H7

7

H074 H075 H076 H077 H078 H079 H080 H081 H082 H083 H084 H085

* Lowbay light fitting - recessed, suspended or ceiling mounted (Thorn Hipak 2, Thorlux Compact 3, Compact 65, Siteco or other approved) :- *(H074 H077) 250 - 400W Mercury, Open 250 - 400W Mercury, lens, louvre or wire guard 250 - 400W SON/MBI, Open 250 - 400W SON/MBI, lens, louvre or wire guard BRANDED LUMINAIRE (Removal of existing luminaire to be measured separately) * The following luminaire including control gear, low loss ballast, connecting wiring, mounting bracket and other accessories *(H078 H252) “AEROLITE” GAMMA 1 x 18W fluorescent luminaire with HF Electronic ballast and daylight/warm white tube “AEROLITE” GAMMA 1 x 3W fluorescent luminaire with HF Electronic ballast and daylight/warm white tube “ARCLUCE” MONOS ceiling mounted luminaire with 18W fluorescent tube, body in extruded aluminum and reeded clear high impact acrylic diffuser “ARCLUCE” MONOS ceiling mounted luminaire with 36W fluorescent tube, body in extruded aluminum and-reeded clear high impact acrylic diffuser “ARCLUCE” MONOS 1021 with 36W fluorescent tube (1P40) oval-shaped extruded aluminum tubular system and reeded prismatic diffuser “ARCLUCE” ORION 240, 2990-10, recessed downlight with 4mm frosted glass protector and 18W lamp “ARIES” CLASSIC MOD 683 wall mounted luminaire with 13W PLC/l8W PLC lamp, die cast aluminum body and acrylic diffuser “ARIES” CLASSIC MOD 684 wall mounted luminaire with die-cast aluminum structure and polyester powder coated paint and l3W/18W PLC/SC 18W lamp


280.00 380.00 420.00 480.00 68.70 80.20 100.90 134.00 135.80 228.70 93.85 85.85

SOR Page H8

8

H086 H087 H088 H089 H090 H091 H092 H093 H094 H095 H096 H097 H098 H099 H100

“ASTRIUM” TV21Q decorative semi-recessed wall luminaire in cast aluminum with frosted polycarbonate diffuser and 2 x 10W or 2 x 7W PLC lamps “BEGA” 2489 wall mounted luminaire with 13W PLC lamp and die-cast aluminium body “BEGA” 2926 recessed wall mounted luminaire with 183W PLC lamp, aluminium alloy and stainless steel body “BEGA” 2491 wall light (1P45) with 26W PLC lamp “BERGNER & WEISER” art no. 7151.1(W) wall/ ceiling mounted luminaire wtih die-cast aluminum body, polycarbonate diffuser and 13W TC-D lamp “BERGNER & WEISER” art no. 7l51.lM(W) wall/ceiling mounted luminaire with die-cast aluminum body, polycarbonate diffuser and 13W TC-D lamp “BOLUCE” ASTRA 9323, wall mounted luminaire with 2 x 9W PL lamps “BOLUCE” GAMMA 1093, recessed wall mounted luminaire with grille and 9W PL lamp “COSMO” C 0380/218 cast aluminum ceiling mounted luminaire with opal polycarbonate diffuser with 2 x PLC 18W lamps “DAIKO” DWP 18642 updown wall light in cast aluminum with diffuser with 18W PLC lamp “DAIKO” DWP-l865l wall light in cast aluminum with diffuser with 13W PLC lamp “DEFA” NEPTUNE OO3AS 121201 wall/ceiling mounted luminaire with 26W PLC lamp and polycarbonate diffuser “DIAKON” diffuser luminaire (WSLD Series) with prismatic diffuser, end caps and 36W tube “DIL MESADO” Square Art 000l/PL-ll ceiling mounted luminaires with 2 x 11W PL lamps, hammered aluminum reflector, sand-blasted polycarbonate diffuser, die-cast aluminum base and ring “DIL-MESADO” SQUARE MSL218 surface mounted luminaire with 2 x PLC—18W lamps, die cast aluminum housing enameled with epoxy powder, sand blasted polycarbonate diffuser and hammered aluminum reflector

No. No. No. No. No. No. No. No. No. No. No. No. No. No. m

280.00 221.40 221.40 368.00 141.10 168.15 146.45 134.85 160.05 260.00 295.00 162.90 35.80 113.50 99.00

SOR Page H9

9

H101 H102 H103 H104 H105 H106 H107 H108 H109 H110 H111 H112

“DIL” ROLLER 85 ceiling-mount separate tubular luminaire comprising extruded aluminum tubular body with 36W fluorescent lamp, polycarbonate diffuser, ceiling bracket, terminal flange and flat plug “DISANO” Model 2100 KENDO fluorescent luminaire with 36W fluorescent lamp and end cap “DISANO” Model 2100 KENDO fluorescent luminaire with 18W fluorescent lamp and cap “DUTCH-LITE” KL 7943 recessed downlight with 2 x 13W PL lamps ring diameter 225mm & reflector “DUTCH-LITE” 6301 decorative wall luminaire in cast aluminum with vandal resistant glass diffuser and 125W metal halide mercury lamp “EUROTEC” 220 561 1 x 150W metal halide down wall light body made of compact and sturdy corrosion resistant die-cast light alloy, safety tempered glass lens, with up-throw narrow beam and asymmetrical wide beam down-throw, IP 65 “EUROTEC” BLOCK 1 x 18W PLC recessed wall light with die-cast aluminum housing, stainless steel front panel, and UV stabilized opal polycarbonate1diffuser, IP55 “EUROTEC” CIN-ECO/FL26 1 x 26W PLC wall mounted up/down light with UV stabilize polycarbonate prismatic diffuser, super pure aluminum reflector & integral magnetic ballast “EUROTEC” CING/MINISOSIA Opal 1 x 150W metal halide suspended light die-cast alloy anodised extruded aluminum housing with extruded aluminum reflector, opal polycarbonate diffuser with colour filler attachment “EUROTEC” SAVA 1 x 18W or 1 x 36W surface mounted fluorescent filling with powder coated galvanised steel housing and wrap- round prismatic diffuser “EUROTEC’ TO5EOS 2 x 18W PLC surface mounted with white pressed steel housing, vacuum metallized silver anodized reflector & integral electromagnetic ballast “FABRIKANT” 1014 recessed wall mounted luminaire (IP54) with 18W PLC Lamp


220.00 152.30 135.80 137.75 630.00 550.00 150.00 185.00 485.00 52.00 165.00 177.00

SOR Page H10

10


“FISCHER” SAPPHIRE wall/ceiling mounted luminaire with 2 x 18W PLC lamps “GHIDINI” OVALLA Cat. No. BL 1101.1 wall mounted luminaire with 2 x 9W or 2 x 11W PL lamps “GHIDINI” OVALLA 1103 wall mounted luminaire with die-cast aluminum body and opal diffuser, side mounting and 2 x 9W or 2 x 11W PL lamps “GHIDINI” OVALLA 1104 wall mounted luminaire with die-cast aluminum body opal diffuser, end mounting and 2 x 9W or 2 x 11W PL lamps “GOCCIA 2898 wall light with 2 x 9W or 2 x 11W PL lamps “GOCCIA” ILLUMINAZIONE TRIANGOLO wall mounted luminaire with 70W SON or BOW metal halide lamp polycarbonate body and vandal proof diffuser “GOCCIA” TRIANGOLO 4322 wall/ceiling luminaire with 2 x 11W PL lamps and vandal-proof acrylic diffuser “GOCCIA” TRIANGOLO 4346 wall/ceiling luminaire with 2 x 18W PL lamps and vandal-proof acrylic diffuser “GOCCIA” TRIANGOLO 4380 wall/ceiling luminaire with 80W metal halide mercury lamp “IGUZZINI GRID” 7058 (1P66) surface mounted fitting in die cast aluminum frame and frosted polycarbonate diffuser with 2 x 11W or 2 x 18W PLC lamps “ILMAS” STUDIO LINE 1 x 18W fluorescent luminaire with HF Electronic ballast and daylight / warm white tube “ILMAS STUDIO LINE 1 x 36W fluorescent luminaire with HF Electronic ballast and daylight / warm white tube ‘INNOLUX° WMTL 9732118 wall mounted luminaire with die-cast aluminum body, polycarbonate diffuser and 18W PLC lamp “INNOLUX” S4509ll8 wall mounted lighting with die-cast aluminum body, tempered glass diffuser and 18W PLC lamp “INNOLUX” P1496126 wall mounted lighting with die-cast aluminum, reeded glass diffuser and 26W PLC lamp

No. No. No. No. No. No. No. No. No. No. No. No. No. No. No. No.

130.00 92.15 101.85 103.90 87.30 156.05 135.40 146.90 160.70 140.00 63.50 75.00 142.60 161.00 197.90

SOR Page H11

11


“INNOLUX WP 157027 die cast aluminum weatherproof 1P55 with pressed glass diffuser, anodised aluminium reflector and 2 x 7W PL lamps “INNOLUX’ WS 675918 wall mounted, aluminum luminaire with 18W PLC lamp, sand blasted glass and weatherproof 1P55 body “ITT REISS” Square light SQL 300/211 ceiling mounted luminaires with 2 x 11W PL lamps and polycarbonate diffuser “KL LICHT KEGEL-HALB 1121, PLC wall mounted fitting with 18W PLC lamp ‘KL LICHT RADIUS” 1341, PL wall mounted mounted fitting with 11W PL lamp “KL LICHT” ZYLINDER-QUADRO 1581 wall mounted luminaire with 70W SON/5OW or 80W metal halide lamp, body in cast aluminium and cylindrical opal UVstabilized polycarbonate diffuser “KL LICHT” ZYLINDER-QUADRO 1583 wall mounted luminaire with 70W SON/5OW or 80W metal halide lamp, body in cast aluminium with anti-glare louvres and built in cylindrical clear UV-stabilized polycarbonate diffuser “KL LICHT” TRAPEZ 5007 wall mounted luminaire with 70W SON/80W or 125W metal halide lamp, body in cast aluminium and frosted UV-stabilized polycarbonate diffuser “LIGHTCRAFT” AGT 146/P3-2 Telescopic with 2 lanterns and 26W PLC lamps “LIGHTCRAFT” AGT 146/P3-1 Telescopic with 1 lantern with 26W PLC lamp “LIGHTCRAFT” AGT 180/P3-l Telescopic lantern with 26W PLC lamp “LK” SKOT MAXI wall/ceiling mounted luminaire with 70W SON or 80W metal halide lamp, polycarbonate diffuser and die-cast aluminum body “LOCADI” ARTE STRIPES20l8 wall/ceiling mounted luminaire with 18W PLC or 26W PLC or 2 x 9W PL lamps, die cast aluminum housing and UV stabilised vandal proof diffuser “LOCADI” ARTE STRIPE S1010 wall/ceiling mounted luminaire with 10W PL or 13W PLC lamp, die cast aluminum housing and UV stabilised vandal proof diffuser “LOCADI” ARTE GRID Ll018 wall/ceiling mounted luminaire with 18W PLC or 26W PLC or 2 x 9W PL lamp, die cast aluminum housing and IN stabilised vandal proof diffuser

No. No. No. No. No. No. No. Set Set Set No. No. No. No.

215.35 215.35 106.70 276.00 253.00 980.00 1080.00 687.75 533.50 388.00 320.10 360.00 103.90 95.85 103.90

SOR Page H12

12

H143 H144 H145 H146 H147 H148 H149 H150 H151 H152 H153 H154

“LOCADI” ARTE STRIPE S2010 wall/ceiling mounted luminaire with 10W PL or 13W PLC lamp, die cast aluminum housing and UV stabilised vandal proof diffuser “LOTHUS” WAGNER 106 wall mounted luminaire with 18W PLC lamp and UV resistant polycarbonate glazing and cast aluminum body “LUCERNE” 502 wall mounted luminaire with 2 x 11W PL lamps, body in die-cast aluminum and frosted UV-stabilized polycarbonate diffuser “LUCERNE” 502 wall mounted luminaire with 2 x 13W or 2x 18W PLC lamps, body in die-cast aluminum and frosted UV- stabilized polycarbonate diffuser “LUCERNE” 270-G surface mounted wall light (1P54) with 2 x 9W PL lamps “LUXLITE” wall cylinder WC 150 with 2 x 13W PLC lamps “LUMENAX WAVE” 9001 1 x 18W surface mounted fluorescent luminaire with white powder coated steel or aluminium back refeictor, reeded ABS end-cap and end-cover, and daylight/warm white tube “LUMENAX WAVE” 9002 2 x 18W surface mounted fluorescent luminaire with white powder coated steel or aluminum back refelctor, reeded ABS end-cap and end-cover, and daylight/warm white tube “LUMENAX WAVE” 9003 1 x 36W surface mounted fluorescent luminaire with white powder coated steel or aluminum back refelctor, reeded ABS end-cap and end-cover, and daylight/warm white tube “MARCIO”-RAMA Code NX 4043 wall mounted No. 140.65 surface luminaire with 70W SON or 80W mercury vapour lamp, injection moulded impact resistant polycarbonate housing, clear injection moulded polycarbonate diffuser with internal prisms and high purity aluminum reflector (IP65) “MARCIO” (37226 & 00642) recessed downlight with die-cast aluminum ring, polished aluminum reflector, sand-blasted glass diffuser and 2 x 18W PLC lamps MARCIO (SA4) ceiling/column-mount surface luminaire with die-cast aluminum housing, opal polycarbonate diffuser and 2 x 9W PL lamp


97.80 174.15 100.95 108.95 87.30 236.40 44.00 88.00 62.00 140.65 238.00 180.00

SOR Page H13

13

H155 H156 H157 H158 H159 H160 H161 H162 H163 H164 H165 H166 H167 H168

“MARCIO” (6749) column-mounted surface luminaire with die-cast aluminum housing, up-down visor, sand-biased polycarbonate diffuser and 18W PLC lamp “MARCIO” 2081 wall-mount surface luminaire with pressured aluminum housing opel tempered glass diffuser and 36W PLC compact fluorescent lamp A “MATSUSHITA” HS 1002 Opal diffuser with 2 x PL 9W lamps “MAXRAY” MD2668-01 recessed wall washer downlight with aluminum reflector and 18W PLC lamp “MAXRAY” MX8282-01 recessed downlight with anti-glare white cone with 18W PLC lamp “MERZ” horizontal downlight with 18W PLC lamp “MEYER” 16222 wall/ceiling mounted luminaire with opalescent polycarbonate diffuser, reflector and 13W or 18W PLC lamp “MEYER” 16322 wall mounted luminaire in black/white finishing, opalescent polycarbonate diffuser, die-cast aluminum housing, ballast, capacitor, mounting bracket & 18W PLC energy saving lamp “MEYER” wall mounted luminaire 16322 with opalescent white/transparent polycarbonate diffuser, reflector and 13W or 18W PLC lamps “MODUS PET” 330 Code PN 112.9006 ceiling mounted luminaire with 2 x 11W compact fluorescent lamps, die-cast aluminium base and ring with epoxy powder coating, hammered aluminium reflector and sand-blasted polycarbonate diffuser. “NIBA” QUASAR ceiling mountd luminaire Cat No. 3688 with opal diffuser, frame in orange-Red, pc white base in self extinguishing thermoplastic & external stainless steel screws with 2D 28W warmwhite lamp “NORAL” EXPO IVA wall mounted luminaire with 26W PLC lamp or 50W/ 80W mercury super deluxe lamp, bracket and acrylic diffuser “NORAL” MARBELLA wall mounted luminaire with 11W PL or 13W PLC or 18W PLC or 2D 16W lamp and polycarbonate diffuser “NORAL” NORA lllF wall mounted luminaire with 13W or 18W PLC lamp or 50W mercury super deluxe lamp and polycarbonate diffuser

No. No. No. No. No. No. No. No. No. No. No. No. No. No.

176.00 388.00 129.00 130.00 95.00 68.85 104.75 86.00 97.85 126.10 114.45 494.70 98.95 577.15

SOR Page H14

14


H169

H170

H171

H172

H173

H174

H175

H176

H177

H178

H179

H181

“NORAL” PORTO wall mounted luminaire with 9W PL or 13W PLC or 18W PLC or 2D 16W lamp and polycarbonate diffuser “NORAL” ROULETTE II A/F wall mounted luminaire in standard black or white finish with smoke lens made of UV-stabilised polycarbonate and 13W SL lamp “NORAL” SAINT TROPEZ wall/ceiling mounted luminaire with 11W PL or 13W PLC or 18W PLC or 2D 16W lamp and polycarbonate diffuser “NORAL” SANTA CRUZ/MILANO wall/ceiling mounted luminaire with frosted polycarbonate diffuser, silver reflector and 38W warmwhite or daylight Lamp ‘NORALT’ SEVILLA A/F wall mounted luminaire with 13W or 18W or 26W PLC lamp and polycarbonate diffuser “NORAL” TORINO A/F wall mounted luminaire in standard black or white finish with smoke lens made of UV-stabilized polycarbonate and 9W SL lamp “NORAL” TRUMPET F wall mounted luminaire with 9W PL lamp, bracket and polycarbonate diffuser “NOVALUX” Type 5514 decorative wall mounted lurninaire of thermosetting body with frosted diffuser and 18W PLC lamp “NOVALUX” Type 5512 decorative wall mounted luminaire of thermosetting body with frosted diffuser and 2 x 11W PL lamps “NOVALUX” Type 5510 decorative wall mounted luminaire of thermosetting body with frosted diffuser and 2 x 18W PLC lamp “OSRAM” Softlite 18W luminaires lamp Hl80 “PHILIPS” TCS 058/118 fluorescent luminaire No. 69.85 with 18W TLD lamp, in HPF switch start circuitry and opal diffuser “PHILIPS” TCS 058/236 fluorescent luminaire with 2 x 36W TLD lamp HPF switch start circuitry and opal diffuser

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

98.95

254.15

98.95

119.30

342.40

254.15

244.45

103.90

103.90

107.90

180.00

120.30

SOR Page H15

15


H182

H183

H184

H185

H186

H187

H188

H189

H190

H191

H192

“PHILIPS” KOMBI PLB 211 wall mounted vandal - resistant luminaire with 2 x 11W PL lamps “PLANET COSMO” C0380/213 decorative ceiling /wall mounted luminaire in cast aluminium with opal diffuser and 2 x 13W PLC lamp “PLATEK” LEIPZIG 05 wall mounted light fitting, body made of phospho-chromate aluminium coated with polyester paint, UV-stabilized polycarbonate lens and 11W PL or 13W PLC or 18W PLC lamp “PLEAID” 175-76122 recessed downlight with matt aluminium reflector and decorative glass with 18W PLC lamp (without cone) “POLOMITI” Square ceiling luminaire with 2 x 9W PL or 2 x 11W PL lamps “PRISMA” PIUS OVALE 350 spilt wall mounted luminaire with die-cast aluminium housing and UV stabilized polycarbonate diffuser “PROLUX” 1080.20 wall mounted fitting with 15W ELN compact fluorescent lamp, 200mm clear globe and wall bracket “PROLUX” TX118 surface mounted tubular light fittings with 18W fluorescent lamp and prismatic diffuser PULSAR 62030 ceiling mounted luminaire with die cast body 2 x 11W PL lamps “RAAK” recessed downlight R14-0003 ring diameter 190mm with 18W or 21W PLC lamp “ROYCE THOMSON” RTE/PS/KT photocell Kit H193 “SELUX” SX 432-17-2 wall mounted luminaire No. 1010.00 with 50W/80W/125W mercury super deluxe lamp/26W PLC lamp and polycarbonate diffuser

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

148.40

90.00

577.15

165.00

110.60

204.30

104.75

160.05

98.00

276.45

73.70

SOR Page H16

16


H194

H195

H196

H197

H198

H199

H200

H201

H202

H203

H204

H205

H206

“SELUX” Sx 472-20-2 Wall Mounted Luminaire in Black FInishing with clear cylindrical polycarbonate diffuser clear mirror louvre, cast aluminium filter & 80W HME mercury super deluxe lamp “SIEMENS” CAMEO light fitting with 2 x 9W or 2 x 18W PL lamps “SIEMENS” CAMEO with seperate lamp and gear compartment and energy saving 2D 28W or 38W lamps “SIEMENS” MONSUN Damp-proof surface mounted luminaire with 36W lamp “SIEMENS” MONSUN Damp-proof surface mounted luminaire with 2 x 36W lamp “SIEMENS HQL” Super Delux wall mounted fitting custodian with GRP body injection moulded TJV-stabilized polycarbonate prismatic diffuser, white sheet steel reflector and 80W mercury lamp “SIMES” Model 56005 ceiling mounted luminaire with 2 x 11W PL lamps “SIMES” Model S6008 ceiling mounted luminaire with 2D38W lamp “SIMES” #245 decorative waterproof surface mounted luminaire of 1P54 class 1 protection with body in die cast aluminium and 13W PLC lamp “SIMES” VEDO OVAL Art 6709 wall/ceiling mounted luminaire with 18W PLC lamp and sand-blasted polycarbonate diffuser “SIMES” VEDO OVAL Art 6749 wall/ceiling mounted luminaire with 18W PLC lamp and sand-blasted polycarbonate diffuser “SIMES” VEDO OVAL Art 6759 wall/ceiling mounted luminaire with 18W PLC lamp and sand-blasted polycarbonate diffuser “SIMLITE” BS12O 1 x 18W surface mounted ceiling/wall fluorescent luminaire with powder coated white waveform reflector, removable gear tray, male & female connector, and daylight/warm white tube

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

1388.00

130.00

130.00

68.00

95.00

230.00

114.45

119.30

85.10

117.95

132.00

139.10

44.00

SOR Page H17

17


H207

H208

H209

H210

H211

H212

H213

H214

H2l5

H216

H217

H218

“SIMLITE” BS12OE 1 x 18W surface mounted ceiling/wall fluorescent luminaire with powder coated white waveform reflector removable gear tray, male & female connector, electronic ballast, and daylight/warm white tube

“SIMLITE” BS136 1 x 36W surface mounted ceiling/wall fluorescent luminaire with powder coated white waveform reflector, removable gear tray, male & female connector, and daylight/warm white tube

“SIMLITE” BS140E 1 x 36W surface mounted ceiling/wall fluorescent luminaire with powder coated white waveform reflector, removable gear tray, male & female connector, electronic ballast and daylight/ warm white tube

“SUPERCLUB” CLUB/DIAMOND light fitting with 2D 28 or 38W lamp & accessories

“SUPER DELTA” OVALE/G (Prisma 1702) light fitting which 2 x 9W PL lamps

“TERNO-LYRA” TL-M0445/11 decorative ceiling light with 11W PL Lamp

TERMO! 0250/219 ceiling luminaire with diffuser with 2 x PL 9W lamps

“THORLUX” Cat No. PS 7952S Prismalette bulkheed luminaire with 2D 38W or 28W lamp or 2 x PL 11W lamp

“THORLUX” MERCIAN with 70W high pressure sodium lamp (MER9953) or 70W metal halide lamp (MER9954) or Dulux T/E 42W compact fluorescent lamp

“THORLUX” PASSLIGHT with glass cover and 80 or 125W Mercury lamp or 70W high pressure sodium lamp/metal halide lamp

“THORLUX” PRISMATIC with glass cover and 50W mercury lamp (PR3049)

“THORLUX” PISMALUX with glass cover and 80 or 125W mercury 1amp or 50 or 70W High Pressure Sodium lamp or 70W metal halide lamp

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

60.00

62.00

80.50

77.60

70.80

110.60

110.60

165.85

420.00

415.00

250.00

380.00

SOR Page H18

18


H219

H220

H221

H222

H223

H224

H225

H226

H227

H228

H229

H230

H231

H232

“THORLUX” HU-STYLE COM indirect lighting system 2 x 55W with electronic control gear and lamps “THORN” FRAS 218 2 x 18W fluorescent luminaires with FRV 236 louvres “THORN” BERGAIVIE 100W Halogen wall mounted luminaire “THORN” CONCEPT A mounted luminaire with 26W PLC lamp “THORN” DIAMOND DM 28/38 with seperate lamp and gear compartment and 20 28W or 38W lamp “TX” 18W tubular fitting with 75mm diameter low loss ballast starter, capacitor and L18/3l tube “VINIC” 18405/18305 surface mounted wall/ ceiling luminaire die cast aluminium and opal diffuser with 26W PLC lamp and wall bracket “VINIC” 17907/17909 wall mounted luminaire die cast aluminium with 70W SON/metal halide lamp (IP55) “VINIC” 15602 surface mounted luminaire die cast body with white polycarbonate diffuser and 2 x PLC 18W lamps “VINIC” 18004/18007 wall mounted luminaire die cast aluminium with 70W SON/metal halide lamp (1P55) ‘VINIC’ 14101/14102/14103 surface mounted ceiling/wall luminaire similar to ‘WE-EF’ DB 259-DD-26(I) with 13/18/26W PL-C lamp ‘VINIC’ 14503 surface mounted ceiling/wall luminaire similar to ‘WE-EF’ DLG 259-00-26 with 26W PL-C lamp “WE—EF QLL-0259-DF-24 wall mounted luminaire with 24W Dulux lamp and UV stabilised polycarbonate lens H232 “WE-EF” QLL-309-DF-36 wall mounted luminaire with 36W Dulux lamp and UV stabilised polycarbonate lens

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

820.00

156.15

120.30

226.00

130.00

149.40

180.00

335.00

157.00

430.00

243.70

240.00

310.00

388.00

SOR Page H19

19


H233

H234

H235

H236

H237

H238

H239

H240

H241

‘TWE-EF” QLL-309-DF-2/36 wall mounted with 2 x 36W Dulux lamp and UV stabilized polycarbonate lens

“WE-EF” QRL-309--E-50/80 wall mounted with 50 or 80 mercury super deluxe lamp and UV stabilized polycarbonate lens

“WE-EF” QRL-309-E-50/70N1.wall mounted luminaire with 50 or 70 SON lamp and UV stabilized polycarbonate lens

11WE-EF” DRB2S9-DD--13(I) recessed wall luminaire, corrosion resistant die- cast aluminium alloy body and frame, finish in PAL polyester powder coat, polycarbonate UV-stabilized and vandal resistant diffuser, weatherproof 1P55 and durable silicone gasket and 13W PLC lamp

“WE-EF” DRB259-DD-18(I) recessed wall luminaire, corrosion resistant die- cast aluminium alloy body and frame, finish in PAL polyester powder coat, polycarbonate UV-stabilized and vandal resistant diffuser, weatherproof 1P55 and durable silicone gasket and 18W PLC lamp

“WE-EF” DR3259-DD-26(I) recessed wall luminaire, corrosion resistant die- cast aluminium alloy body and frame, finish in PAL polyester powder coat, polycarbonate UV-stabilized and vandal resistant diffuser, weatherproof 1P55 and durable silicone gasket and 26W PLC lamp

“WE-EF” DLB259-DD-13(I) surface wall luminaire, corrosion resistant die- cast aluminium alloy body and frame, finish in RAL polyester powder coat, polycarbonate UV-stabilized and vandal resistant diffuser, weatherproof 1P55 and durable silicone gasket and 13W PLC lamp

“WE-EF” DLB259-DD-18(I) surface wall luminaire, corrosion resistant die- cast aluminium alloy body and frame, finish in PAL polyester powder coat, polycarbonate UV-stabilized and vandal resistant diffuser, weatherproof 1P55 and durable silicone gasket and 18W PLC lamp

“WE-EF” DLB2S9-DD-26(I) surface wall luminaire, corrosion resistant die- cast aluminium alloy body and frame, finish in PAL polyester powder coat, polycarbonate UV-stabilized and vandal resistant diffuser, weatherproof 1P55 and durable silicone gasket similar to ‘Vinic’ 14101/14102/14103 and 13/18/26W PLC lamp

No.

No.

No.

No.

No.

No.

No.

No.

No

420.00

588.00

600.00

234.00

235.90

224.20

223.60

226.10

243.70

SOR Page H20

20


H242

H243

H244

H245

H246

H247

H248

H249

H250

H251

H252

“WE-EF” DLG 259-DD-26 surface mounted ceiling/wall luminaire similar to ‘VINIC’ 14503 with 26W PL-C Lamp

“WE-EF” LIGHTSPIKE LSA 050-E-50/80 wall mounted luminaire with 50 or SOW mercury super deluxe lamp, die cast aluminium body and UV stabilized polycarbonate lens

“WE-EF” LIGHTSPIKE LSA 050-E-70H wall mounted luminaire with 70W metal halide lamp, die cast aluminium body and UV stabilized polycarbonate lens

“WE-EF” LIGHTSPIKE LSA 050-E-50/70N1 wall mounted luminaire with 50 or 70W SON lamp, die cast aluminium body and UV stabilized polycarbonate lens

“ZUMTOBELL” Cat No. HS1002 with 2 x 11W PL lamps

“ZYMI” 3923 decorative wall light with opal diffuser and 18W PLC lamp

“3E AMANDINE” 1580 decorative wall luminaire in cast aluminium with frosted diffuser and 18W PLC lamp

“3E1” 025 decorative updown wall light in cast aluminium lens with •l3W PLC and 18W PLC lamps and ballasts

“LUMENAX WAVE” 900]. 1 x 18W surface mounted fluorescent luminaire with white powder coated steel or aluminium back reflector, reeded ABS end-cap and end-cover, HF electronic ballast and daylight/warm white tube

“LUMENAX WAVE” 9002 2 x 18W surface mounted fluorescent luminaire with white powder coated steel or aluminium back reflector, reeded ABS end-cap and end-cover, HF electronic ballast and daylight/warm white tube

“LUMENAX WAVE” 9003 1 x 36W surface mounted fluorescent luminaire with white powder coated steel or aluminium back reflector, reeded ABS end-cap and end-cover, HF electronic ballast and daylight/warm white tube

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

240.00

820.00

850.00

830.00

129.00

180.00

180.00

285.00

60.00

111.00

80.50

1

I - FAN

Contents SOR Page

1. Removal of Existing Fan I1

2. Exhaust Fan I1

3. Wall and Ceiling Fan I1 – I2

4. Fan Parts and Accessories I2

5. Fan repair / Installation I2

SOR Page I1

1


I001

I002

I003

I I004

I005

II006

I007

I008

I009

I I010

I. FAN

REMOVAL OF EXISTING FAN

Remove existing exhaust, ceiling or wall mounted fans including regulator if any including reinstatement and disposal off site (New fan to be measured separately)

EXHAUST FAN

* Supply and install new exhaust fan of the following size :- (Removal of existing fan to be measured separately) *(1002 1004)

Exhaust fan 300mm (KDK, National, Mitsubishi)

Exhaust fan 450mm High Pressure (Industrial Type) (1400 RPM) (KDK, National, Mitsubishi)

Exhaust fan 600mm High Pressure (Industrial Type) (920 RPM) (KDK, National, Mitsubishi)

WALL AND CEILING FAN

* Supply and install the following ceiling / wall fan (Removal of existing fan to be measured separately) *(I005 I011)

400mm diameter Auto rotating ceiling fan (KDK, National, Mitsubishi)

400mm diameter wall bracket fan with pull cord regulator and switch (KDK, National, Mitsubishi)

500mm diameter wall bracket fan with pull cord regulator and switch (1<01<, National, Mitsubishi)

508mm diameter wall fan 240V, 1400 rpm 50Hz (wing-Ton Model 303, Imasu/Tornado Model DF 500-TW)

635mm (25) diameter wall fan 240V, 1400 rpm 50 Hz (wing-Ton Model 303, Imasu/ Tornado Model DF 650-TW)

635mm diameter “KOUKYU” wall fan 240V, 1400 rpm 50 Hz Model 303 (MG)

No.

No.

No.

No

No

No.

No.

No.

No.

No.

9.70

97.00

368.60

776.00

158.10

135.80

280.80

240.55

271.60

203.70

SOR Page I2

2


I011

I012

I013

I014

I015

I I016

I017

l.5m diameter sweep ceiling fan regulator and teak board (KDK, National, Mitsubishi)

FAN PARTS AND ACCESSORIES

Hook for ceiling fan installed to existing concrete ceiling including cutting mortice in concrete

Regulator for ceiling fan

Fan condenser for 400mm or 500mm diameter wall bracket fan in replacement

Fan gear for industrial wall fan in replacement

FAN REPAIR/INSTALLATION

Repair/rewind of fan motor coil for 400mm or 500mm diameter wall bracket fan

Take delivery from any store, transport, cut stem as required and fix fan and regulator (hook not included)

No.

No.

No.

No.

No.

No.

No.

72.70

5.80

15.50

12.60

72.75

38.80

31.20

1

J LAMP, BULB, TUBE & BALLAST

Contents SOR Page

1. Bulb J1

2. Fluorescent Tube J1 – J2

3. Parts and Accessories for Fluorescent Fitting J2 – J3

4. Compact Fluorescent Lamp / Tube J3 – J4

5. Halogen Bulb / Lamp / Tube J4 – J5

6. Halogen lamp Accessories J5 7. Lamp for Garden / Street Lights J5-J6 8. Ballast and Lamp Accessories J6–J7 9. Other Lamp Accessories J7

1


J001

J002

J003

J004

J005

J006

J007

J008

J009

J010

J011

J012

J013

J014

J015

J. LAMP, BULB, TUBE & BALLAST

BULB

Tungsten incandescent lamp bulbs 15W to 100 W

Candle bulb 15 - 60W 230V BC or ES, clear or frosted (Philip, Splendour, Osram, , Tungram)

Colour bulb GLS, round or pygmy SW to 40W

60W to 150W Par 38 lamp (Philip, Thorn, Splendour, Sylvania, Osram)

100W bulb for roof top aviation light

100 watts GLS coiled tungsten incandescent bulb with ES caps for aircraft warning light

GLS pear shape 25-100W 230V clear or frosted

Ping-pong 15-SOW 230V BC or ES, clear or frosted

Par 38 60-150W E27 spot or flood

60-100W 16,000 hrs bulb for aircraft warning light

Par 56 300W 12V or 230V spot or flood

Par 64 300-100W GX1SD or screw terminal

FLUORESCENT TUBE

450/600mm 18W energy saving fluorescent tube (daylight) (Philips, Hitachi, GE, Osram)

900mm 30W energy saving fluorescent tube (daylight) (Philips, Hitachi, GE, Osram)

1200mm 36W energy saving fluorescent tube (daylight) (Philips, Hitachi, GE, Osram)

No

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

1.70

1.40

1.60

11.65

2.50

4.35

1.50

1.50

10.00

19.00

65.00

120.00

1.60

3.00

3.30

2


J016

J017

J018

J019

J020

J021

J022

J023

J024

J025

J026

J027

J028

J029

J030

J031

J032

J033

1500mm 58W energy saving fluorescent tube (daylight) of 230V (Philips, Hitachi, GE, Osram)

600MM 18W energy saving fluorescent tube (warm or cool white) (Philips colour 83/84, GE, Osram Lumilux 31, Sylvania)

900MM 30W energy saving fluorescent tube (warm or cool white) (Philips colour 83/84, GE, Osram Lumilux 31, Sylvania)

1200mm 36W energy saving fluorescent tube (warm or cool white) (Philips colour 83, Osram Lumilux 31/21 Sylvania, GE)

* Circular fluorescent tube of the following *(J020 J025)

20-32W daylight

40W daylight

20-32W warmwhite

40W warmwhite

20-32W Super80 (colour 80 series)

40W Super80 (colour 80 series)

* Slim fluorescent tube of the following :-*(J026 J027)

T5, 15mm 4-8W daylight tube (Osram, Hitachi, National)

T8, 26mm 18-36W daylight tube (Osram, Hitachi, Nationa)

Osram Circolux-EL 28-32W E27

10W mini fluorescent tube (daylight)

PARTS & ACCESSORIES FOR FLUORESCENT FITTING

Lampholder for fluorescent lamp (all tube diameter and Sizes)

Starter for fluorescent lamp (Philips, Osram, Megaman)

Fluorescent starter holder

Fluorescent dimmer controller (Osrarn MCU)

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

Pair

No.

No.

No.

3.80

4.65

5.05

4.50

5.20

6.30

17.00

19.00

24.00

24.00

6.00

5.60

40.00

3.22

1.95

1.05

1.25

100.00

3


J034

J035

J036

J037

J038

J039

J040

J041

J042

J043

J044

J045

J046

Capacitor 3.25/5/8 mfd for fluorescent lamp Fused terminal with 2A fuse (BG) Moulded prismatic/reeded/opal/frosted diffuser for 1 x 18W or 1 x36W mounted channel fluorescent luminaries (for Aerolite, Eurotec, Ilmas, Lumenax, Simlite, Thorlux, Philips, ITT-Reiss, Siemens, Thorn) Moulded prismatic/reeded/opal/frosted diffuser for 2 x 18W or 2 x 36W mounted channel fluorescent luminaries (for Aerolite, Eurotec, Ilmas, Lumenax, Simlite, Thorlux, Philips, ITT-Reiss, Siemens, Thorn) Flat prismatic/reeded/opal/frosted diffuser only for recessed light (Simlite, Davis, Trimex, Woolite) End cap or decorative cap of ABS materials for 1 x 18W / 36W fluorescent luminaires COMPACT FLUORESCENT LAMP/TUBE * Compact Fluorescent/Energy Saving bulb-daylight, warmwhite or coolwhite of the following :- (Osram, Philips, Sylanvia, GE) *(J040 J055) 5-11W 2 pin (GE Biax-S, Osram Dulux-S, Philips PLS, Sylvania Lynx-S) 5-11W 4 pin (GE Biax-S/E, Osrarn Dulux-SE, Philips PLS, Sylvania Lynx-SE) 10-26W 2 pin (GE Biax-D, Osram Dulux-D, Philips PLC, Sylvania Lynx-D) 10-26W 4 pin (GE Biax-D/E, Osram Dulux-DE, Philips PLC, Sylvania Lynx-DE) 13-26W 2 pin (GE Biax-T, Osram Dulux-T or T/IN, Philips PLT, Sylvania Lynx-T) 32W 2 pin (Osram Dulux-T or other approved) 13-26W 4 pin (GE Biax-T/E, Osram Dulux-T/E or TIE/IN, Philips PLT, Sylvania Lynx-TE)

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

2.80

6.00

12.00

15.00

32.00

4.00

8.50

12.00

13.50

15.00

16.00

22.00

26.00

4


J047

J048

J049

J050

J051

J052

J053

J054

J055

J056

J057

J058

J059

J060

J061

J062

32-42W 4 pin (GE Biax - T/E, Osram Dulux-T or T/E/IN, Philips PLT, Sylvania Lynx-TE)

18-36W 2 pin or 4 pin (GE Biax-L, Osram Dulux-L, Philips PLL, Sylvania Lynx-L-LE)

40-55W 2 pin or 4 pin (GE Biax-L, Osram Dulux-L, Philips PLL, Sylvania Lynex-L-LE)

18-36W 4 pin (Osram Dulux F or other approved)

7-11W (GE Electronic Biax D or M, Osram Dulux-EL, Philips PLEU, Sylvania Mini Lynx)

15-25W (GE Electronic Biax T, Osram Dulux- EL, Philips PLET)

18-25W (Osram Dulux-EL, Eco/Philips SL or other approved)

10W to 40W 2D warm white or daylight. fluorescent lamp 2 or 4 pin (GE, Thorn)

8W Fluorescent tube for emergency exit signs

COMPACT FLUORESCENT LA1IP/TUBE’S ACCESSORY

2 pin or 4 pin type compact fluorescent tube/2D fluorescent’s lamp holder

Screw mounting type compact fluorescent tube’s holder

HALOGEN BULB/LAMP/TUBE

35mm Halogen lamp l2V 20W-50W (Osram, Philip, Thorn)

51mm Halogen lamp 12V 20W-SOW (Osram, Philip, Thorlux)

* Halogen tube double-ended of the following :- (Philip, Osram, GE, Sylvania) *(J060 J062)

100-250W 77mm R7S tube

150-500W 117mm R7S tube

750-1000W 189mm R7S tube

No.

No.

No.

No.

No.

No.

No.

No

No.

No.

No.

No.

No.

No.

No.

No.

32.00

25.00

28.00

32.00

25.00

28.00

25.00

15.50

3.30

4.25

5.25

7.75

9.00

9.50

11.00

16.00

5


J063

J064

J065

J066

J067

J068

J069

J070

J071

J072

J073

J074

J075

J076

J077

J078

J079

* Halogen tube single-ended of the following :- (Osram, GE, Sylvania, Halolux, Philips) *(J063 J064) 60-250W B15D 230V clear or frosted

60-250W E27 230V clear or frosted * Halogen par E27 230V of the following :- (Philips, Osram, Sylvania, GE) *(J065 J066)

Par 20 50W Spot or flood

Par 30 75-100W Spot or flood* Halogen Capsule l2V of the following :- (Osram, Philips, GE, Sylvania) *(J067 J069)

6V 10W G4

12V 10-20W 0-4

12V 35-100W G6.35

Halogen Lamp Accessories Ceramic holder for 50W/20W halogen / bulb / lamp

l2V transformer 50VA to 75VA for halogen lamp (Vossloh-Schwabe, Optima, TCI)

LAMP FOR GARDEN/STREET LIGHTS * High Pressure Sodium Vapour SON lamp with E27/E40 base of the following :- (Osram, Philips, GE, Sylvania) *(J072 J076)

50-70W E27 (Elliptical or tubular, including built-in Igniter lamp)

70-150W Rx7S double-ended

100-150W E40 (Elliptical or tubular)

250W E40 (Elliptical or tubular)

400W E40 (Elliptical or tubular) * Mercury Lamp with E27/E40 base (Osram, Philips, GE) *(J078 J083)

160W BC or ES Blended/self-ballasted 230V

250W E40 Blended/self-ballasted 230V

50-125W

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

36.00

32.00

29.00

38.00

7.00

7.00

8.00

3.10

24.00

34.00

90.00

45.10

55.00

62.00

12.90

17.50

12.90

6


J080

J081

J082

J083

J084

J085

J086

J087

J088

J089

J090

J091

J092

J093

250W E40

400W E40

Super De-Luxe 50-125W

400W HPI Bus high pressure metal halide gas discharge lamp with E40 base, “PHILIPS” or other approved type * Metal Halide Lamp with E270 or E40 base (Osram, HQI, Philips HPI/MHN-TD) *(J084 J089)

70-150W double-ended Rx7s base (warmwhite, coolwhite, daylight)

250W double-ended FC2 base (warmwhite, coolwhite, daylight)

400W double-ended FC2 base (warmwhite, coolwhite, daylight)

70-150W E27 clear or frosted (warmwhite, coolwhite)



400W MBIF high pressure metal halide lamp G53455 igniter & E40, porcelain lampholder, “THORN” or other approved type.

250W MBIF metal halide lamp with metallic additives igniter & E40 base “THORH” or other approved type

200 watts E/27 Rough Device lamp bulb

BALLAST AND LAMP ACCESSORIES

Low loss ballast 18W to 36W for fluorescent and 2-D lamp or 9W to 26W for compact fluorescent lamp (ATCO, Helvar, Vossloh Schwabe)

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

26.00

32.00

35.00

96.80

78.00

130.00

160.00

95.00

75.00

85.00

165.85

145.50

14.55

9.40

7


J094

J095

J096

J097

J098

J099

J100

J101

J102

J103

J104

J105

J106

J107

J108

J109

J110

J111

* Non-Dimmable electronic ballast, PSB tested and PUB approved type for the following :— (Osram, Schwabe, Helvar Tritronic) *(J095 J098)

1 x 18W or 36W for TB 26mm diameter fluorescent lamp

2 x 18W or 36W for T8 26mm diameter fluorescent lamp

QT 9 - 13W for compact Fluorescent lamp

QT 18 - 26W for compact Fluorescent lamp

QT 36 - 40W for Dulux-L or PL-L lamp * Dimmable electronic ballast for fluorescent lamp PUB approved type (Osram, Helvar, Schwabe, Tritronic) *(J099 J100)

1 x 18W or 1 x 36W

2 x 18W or 2 x 36W * Ballast for H.I.D (Vossloh—Schwabe, Atco, Parmar, Helvar) *(J102 J105)

Mercury 50-125W

Mercury 250-400W

HPSV (SON) & Metal Halide 70W

HPSV (SON) & Metal Halide 100W to 150W

HPSV (SON) & Metal Halide 250W to 400W

OTHER LAMP ACCESSORIES Superimposed igniter for 70W to 400W high pressure sodium or metal halide lamp (Philips, Parmer, Bag Turgi, Thorn)

E27 Porcelain lampholder for discharge lamp

E40 Porcelain lampholder for discharge lamp

White moulded insulated bayonet-type batten lampholder, 5 Amp with skirt, 3 terminals and loop-in earth terminal similar to Delta Cat No. 1031 or other approved

White ceiling rose three terminals 5 Amp. similar to Delta Cat No. 1200 or other approved

Adaptors to lamp holders

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No.

No

No.

35.00

55.00

65.00

85.00

98.00

150.00

190.00

27.80

45.00

22.10

39.30

56.60

38.00

13.85

16.50

4.45

4.85

2.40

8

K NOT IN USE

5

L NOT IN USE

1

M NOT IN USE

1

N FLOODLIGHT/STEPLIGHT/BURIED LIGHT/SPOTLIGHT

Contents SOR Page

1. Removal of Existing Floodlight N1

2. Floodlight/Steplight/Buried Light/spotlight N1 - N9

3. Mounting Bracket N9

SOR Page N

1

1

Item Description Unit Rate ($) N001 N002 N003 N004 N005 N006 N007

N. FLOODLIGHT/STEPLIGHT/BURIED LIGHT/SPOTLIGHT REMOVAL OF EXISTING FLOODLIGHT Remove existing floodlight/steplight/buried light/spotlight fittings including reinstatement and disposal of site FLOODLIGHT/STEPLIGHT/BURIED LIGHT/SPOTLIGHT * Supply, delivery to site and install the following floodlight/steplight/buried light/spotlight complete with integral control gear including connecting wiring, mounting, brackets, screws, connections and other Accessories (Removal of existing floodlight/steplight/buried light/spotlight fittings to be measured separately) *(N002 N078) “ARCLUCE” ECO 8137 slimline floodiight (1P55), black die cast aluminium housing with cooling fins and 70W SON or 70W metal halide lamp “BERGER & WEISER” model no. 5203 outdoor corrosion resistant spotlight with Par 38 cool beam 100W lamp and ground spike “BLAUET” 1910 recessed steplight in die cast aluminium with lourve translucent polycarbonate diffuser with 11W PL lamp “CING” CASTALDI D16/ECO steplight with 9W PL/l8W PLC/26W PLC lamp and high stress resistant composite technopolymer body “DAIKO” DOD 75571 wall mounted spot luminaire with 150W HQI lamp and antiglare shield “EYELITE” WALLUX MAXI SMS-7277 heavy duty die cast aluminium luminaire with prismatic borosilicate glass diffuser and 70 to 150W SON or metal halide lamp

No. No. No. No. No. No. No.

9.80 322.00 46.10 140.00 151.10 920.00 425.00

SOR Page N

2

2

Item Description Unit Rate ($) N008 N009 N0l0 N011 N012 N013

“EUROTEC” LUMEC/BOXER 1 x 250W metal halide hi-emission wall mounted floodlight, die- cast aluminium body, safety tempered glass with up/down asymmetrical optical system, IP66 “EUROTEC” RUDD DFPAR2OS 1 x 35W PAR2O MH 300K floodlight with inground control gear, hexcell glare louver, die-cast aluminium in black zinc coated stainless steel external hardware and tempered glass lens, IP67 “EXTERIEUR VERT” M2 1P67 buried light, in 18 microns anodized aluminium housing with mechanical resistance glass of 8T or anti vandal polycarbonate 4T), FM 11W lamp, electronic control gear “FABRIKANT” 3026/3023/3028/3029/3024 floodlight of corrosion resistant die-cast aluminium alloy body with cooling fins, hinged and framed safety glass thermal shck resistant, stainless steel locking devices, weatherproof and non-aging silicon rubber gasket with RF 1-76/M/16 spigot cap and 150/250/400 watts tubular/metal halide lamp “HUBBELL” MAGNTJLITER floodlight Cat No. MVM-0250S-l16 with 250W SON lamp and 4024C mounting bracket “HUBBELL” MINILITER floodlight Cat No. MHS-0070S-166 for 240V operation with 70W SON lamp and 4024C mounting bracket

No. No. No. No. No. No.

485.00 385.00 386.10 760.00 520.30 382.30

SOR Page N

3

3

Item Description Unit Rate ($) N014 N015 N0l6 N017 N018 N019 N020 N021 N022 N023

“IGUZZINI” PLATEA 7377 outdoor floodlight in die-cast aluminium, super pure aluminium reflector with asymmetrical beam and 70W metal halide or high pressure sodium lamp “IGUZZINI” PLATEA 7378 outdoor floodlight in die-cast aluminium, super pure aluminium reflector with asymmetrical beam and 150W metal halide or high pressure sodium lamp “IGUZZINI” PLATEA 7395 outdoor floodlight in die-cast aluminium, super pure aluminium reflector with asymmetrical beam and 250W metal halide lamp “IGUZZINI” PLATEA 7379 outdoor floodlight in die-cast aluminium, super pure aluminium reflector with flood beam and 70W metal halide or 80W - 125W high pressure sodium lamp “IGUZZINI” PLATEA 7380 outdoor floodlight in die-cast aluminium, super pure aluminium reflector with flood beam and 150W metal halide or high pressure sodium lamp “IGUZZINI” PLATEA 7394 outdoor floodlight in die-cast aluminium, super pure aluminium reflector with flood beam and 250W metal halide lamp “IGUZZINI” 182° Uplighter Light Up Walk with 13W PLC lamp and die cast aluminium frame “IGUZZINI” 7188/7189° Uplighter Light Up Walk with 50/80W mercury super deluxe lamp respectively and die cast aluminium frame “IGUZZINI” 7180° Uplighter Light Up Walk with 50W white SON lamp and die cast aluminium frame “IGUZZINI” 7178/7179° Uplighter Light Up Walk with 35/70W metal halide lamp and die cast aluminium frame

No. No. No. No. No. No. No. No. No. No.

642.10 657.70 738.20 577.15 612.10 677.10 602.40 717.80 893.40 828.40

SOR Page N

4

4

Item Description Unit Rate ($) N024 N025 N026 N027 N028 N029 N030 N031 N032

“IGUZZINI” 7186/7187° Uplighter Light Up Walk with 50/70W SON lamp and die cast aluminium frame “IGUZZINI” PLATEA 7382 outdoor floodlight in die cast aluminium super pure aluminium reflector with flood beam and 70W metal halide E27 lamp “IGUZZINI” PLATEA 7384 outdoor floodlight in die cast aluminium super pure aluminium reflector with flood beam and 80W metal halide lamp “IGUZZINI” PLATEA 7390 outdoor floodlight in die cast aluminium super pure aluminium reflector with flood beam and SOW SON or metal halide lamp “IGUZZINI” PLATEA 7376 outdoor floodlight in die cast aluminium super pure aluminium reflector with flood beam and 2 x 26W TCT compact fluorescent lamp “IGUZZINI” PLATEA 7385 outdoor floodlight in die cast aluminium super pure aluminium reflector with spot beam and 70W metal halide lamp “IGUZZINI” PLATEA 7386 outdoor floodlight in die cast aluminium super pure aluminium reflector with spot beam and 150W metal halide lamp “IGUZZINI” PLATEA 7387 outdoor floodlight in die cast aluminium super pure aluminium reflector with blade-of-light beam and 70W metal halide lamp “IGUZZINI” PLATEA 7388 outdoor floodlight in die cast aluminium super pure aluminium reflector with blade-of-light beam and 150W metal halide lamp

No. No. No. No. No. No. No. No. No.

828.40 438.10 426.80 722.65 471.40 592.70 627.60 717.80 753.70

SOR Page N

5

5

Item Description Unit Rate ($) N033 N034 N035 N036 N037 N038 N039 N040 N04l N042

“INDALUX” 250-IQN security floodlight with die-cast aluminium housing, borosilicate glass diffuser and 70W SON or metal halide lamp “INDALUX 600-IZX-C/S/D/A floodlight with 150W/250W/400W SON lamp/or 150W/25W/400W metal halide lamp “INNOLUX” S4440MH70 ground buried, aluminium luminaire, toughened glass, weatherproof IP 67 with 70W metal halide lamp “INNOLUX” S4318 MH70 wall mounted aluminium floodlight tempered glass weatherproof IP 65 with SOW metal halide lamp “JETS 5” 84.09.01 outdoor flooding wit.h 250W high pressure sodium lamp “LIGMAN” 50031 spike mounted spotlight with 80W PAR 38 lamp “MARCIO” (1091) recessed step-light luminaire with 2 x 9W PL lamps, pressured aluminium housing & guard, tempered glass diffuser and recess box “MARCIO” (4440) buried uplighter luminaire with 70W metal halide lamp, die-cast aluminium housing, reflector, polypropylene recess-tube and toughened glass diffuser “MARCIO” (4316) floodlight luminaire with 70W metal halide lamp, die-cast aluminium housing, reflector and 70W metal halide lamp “MARCIO” (4819) ground-mounted recessed luminaire with die-cast aluminium housing, 12 windows protective guard, thoughened glass diffuser, polypropylene recess tube and 18W PLC lamp


463.00 811.00 777.90 1001.00 480.00 139.00 242.00 982.00 574.00 642.00

SOR Page N

6

6

Item Description Unit Rate ($) N043 N044 N045 N046 N047 N048 N049 N050 N051 N052 N053 N054

“MAZDA” CONDOR C3 MAIH 400 1P65 floodlight with 400W metal halide (MAIH 400W) lamp, weatherproof metal enclosure and stirrup mounting bracket “MAZDA” CORMORAN 400/1000 E40 floodlight with 250W/400W high pressure sodium vapour or metal halide lamp, weather-proof metal enclosure and stirrup mounting bracket “MEYER” WM 8872-041-000 Floodlight with thermal fatigue resistant safety glass, high gloss mirror reflector, die-cast aluminium body & 150W metal halide lamp “PHILIPS” floodlight Cat No. SWF 330 with 250W/400W SON/T lamp and mounting bracket ”PHILIPS” anti glare weatherproof floodlight Cat No. SNF 300 with 250W SON/T lamp “PHILIPS” anti glare weatherproof floodlight Cat No. SWF 330/SEF 330 with 250W SON/T or 400W HDL/T lamp “PHILIPS” bulk head luminaire Cat No. XGCOO1 with prismatic diffuser, 18W SOX lamp and mounting bracket “SIEMENS” EUROFLOOD 701150 SICOMPACT mini floodlight with 70/150W metal halide or high pressure sodium lamp “SIEMENS” EUROFLOOD 250/400 •SICOMPACT mini floodlight with 250/400W metal halide or high pressure sodium lamp “SIEMENS” SICOMPACT MINI floodlight cat. no. 5NA-747-l-2 of die-cast aluminium housing, hammered aluminium reflector and tempered glass lens with 70W metal halide lamp “SIEMENS” SICOMPACT MINI floodlight cat. no. 5NA-747-2-2 of die-cast aluminium housing, hammered aluminium reflector and tempered glass lens with 150W metal halide lamp “SELUX” MTR luminaire Cat No. SX 563 11-2 with 70W SOI’ lamp, MTR 200 reflector and V accessories


423.90 350.00 642.00 560.00 411.30 499.55 163.90 544.20 636.30 336.60 351.10 939.90

SOR Page N

7

7

Item Description Unit Rate ($) N055 N056 N057 N058 N059 N060 N061 N062 N063 N064

“SIMES” Ring Drive/walk over Art S.4928/4929/4930 with thoughened clear glass diffuser polypropylene tube for recess, 1P67 and 18W PLC-T lamp “SIMES’ MEGAFLAT round buried drive/walk over Art. S.4787 uplight with 70W SON or 125W mercury super deluxe lamp, polyester powder coated cast aluminium housing and toughened glass “SIMES” MEGAFLAT round buried drive/walk over Art. S.4790 uplight with clear thoughened glass diffuser, polypropylene tube for recess, 1P67 and MM 150W metal halide lamp “SIMES” MEGAFLAT round buried drive/walk over Art S.4787/4726/4728 uplight with 1 x MH—1SOW/125W/70W metal halide lamp, clear toughened clear glass diffuser, polypropylene tube for recess, 1P67 “SOLARIS” uplighter with energy saving bulb EL 20 “SPECTRA” SORRENTO STO Sl4560/S14575/Sl4590 recessed steplight with high impact opal acrylic lens and 18W PLC lamp ‘SPECTRA TRENTO S13110/S13112/S131l4/ Sl3104/S13l06/S13l20/Sl3200/S13705/S132l0 Uplighter with high strength borosilicate glass 70W/lOOW/l5OW metal halide lamp or 80W/125W mercury lamp or 70W sodium lamp “THORLUX” PASSLIGHT security floodlight Cat No. PL 6235 with die-cast aluminium housing, primatic glass cover diffuser and 70W SON lamp/SOW metal halide lamp “THORLUX” AZMET 70 Floodlight with 70W high pressure sodium lamp “THORLUX” COMBO Prismatic low glare refractor luminaire with 250W/400W sodium or 250W/400W metal halide lamp


524.00 754.00 962.00 1005.00 173.60 161.00 928.00 425.00 420.00 720.00

SOR Page N

8

8

Item Description Unit Rate ($) N065 N066 N067 N068 N069 N070 N071 N072 N073 N074 N075 N076

“THORLUX” AZMET 3 Floodlight (Spigot mounted or cradle mounted) with 250W/400W sodium or 250W/400W metal halide lamp “THORLUX” ENCLOSED COMBO with hinged glass cover (1P54) and 250W/400W sodium or 250W! 400W metal halide lamp “THORN” CT 70T SON-Pak 7 floodlight with 70W SON lamp “THORN” JALON G 18W PLC recessed horizontal steplight with grille and 18W PLC lamp “THORN” CAS000 CITYSCAPE floodlight with 250W metal halide lamp “THORN” ODW 500 halogen floodlight with K1 250W/500W linear tungsten halogen lamp “THORN” AFSS15OT/250T or AFSK25OT/ area floodlight 40 with l5OW/250W SON or metal halide lamp “THORN” AFSS 400T/AFSK 400T/AFSC 400T area floodlight 40 with 400W SON, mercury or I metal halide lamp ‘VINIC” 50403/50405/50406 surface/pole mounted floodlight with die cast aluminium body, tempered glass cover and 125 WMV/70W/ 50W high pressure sodium lamp “VINIC” 50601/50603/50602/50604 pole mounted floodlight with die cast aluminium body, tempered glass cover and 250 - 400W SON/metal halide lamp “WE-EF” FL31-T-250 M(IC)/FL31-E-250 N(K)/ FL31-T-400 N(K) Floodlight fitting of corrosion resistant die-cast aluminium alloy body with cooling fins, hinged and framed safety glass thermal shock resistant, stainless steel locking devices, weatherproof and non-aging silicon rubber gasket with RF l-76/M/l6 spigot cap and 250W/400W tubular sodium/eliptical sodium! mercury/metal halide tubular lamp “WE-EF” IPSS STG259-DD-13(I) or 18(I.)/STL 259-DD-13(I) or 18(I) corrosion resistant steplight with die-cast aluminium alloy body and frame, polycarbonate UV-stabilized and vandal resistant diffuser, two cable entires to facilitate through wiring and 13W or 18W PLC lamp


695.00 600.00 308.00 126.10 655.70 159.00 371.00 394.00 502.00 740.00 760.00 185.10

SOR Page N

9

9

N077 N078 N079 N080 N081 N082 N083 N084 N085

“WE-EF” STO 259 step light with high impact opal acrylic lens, 13W/18W PLC lamp 150/200W spot light fitting with base holder to wall or ceiling MOUNTING BRACKET Mounting bracket for ‘PHILIPS’ SWF 330/ SEF 330 floodlight “WE-EF” MF1-A-l08 steel mounting bracket for single floodlight on post top column “WE-EF” MF2-A-108 steel mounting bracket for two floodlight on post top column Steel mounting bracket for single flood light luminaire on post top column (other than WE-EF) Steel mounting bracket for two flood light luminaire on post top column (other than WE-EF) “SIMES” Art S4929 ring buried/walk over light fitting with acidated glass, die cast aluminium body and 18W PLC-T lamp “SIMES” PRADO buried drive-over with compact fluorescent lamp low G24d-1 die cast aluminium body 4 windows protective guard of 6mm thickness polypropylene tube and polypropylene vandal proof diffuser

No. No. No. No. No. No. No. No. No.

188.00 27.65 38.15 142.50 257.00 85.50 133.00 425.00 188.00

8

P WEATHERPROOF BOX ND METAL ENCLOSURE Contents SOR Page 1. Weatherproof box and Metal Enclosure P1

SOR Page P

1

1

Item Description Unit Rate ($) P001 P002 P003 P004 P005 P006 P007 P008 P009 P010 P011 P012

P. WEATHERPROOF BOX AND METAL ENCLOSURE “VYNCKIER” Superpolyrel SP 320 500 x 750 x 300 mm with cover, rainhood, air vents, handle, lock, keys and gasket for IPSS “VYNCKIER” Superpolyrel SP 330 750 x 750 x 300 mm with cover, rainhood, air vents, handle, lock, keys and gasket for 1P55 “TVYNCKIER” Superpolyrel SP 430 1000 x 750 x 300 mm with cover, rainhood, air vents, handle, lock, keys and gasket for 1P55 160 x 135 x 77 mm PVC rectangular box with cover “LEGRAND” Cat No. 92106 or other approved 310 x 240 x 154 mm PVC rectangular box with hinged cover, “LEGRAND” Cat. No. 35054 or other approved 85mm x 85mm x 30mm PVC box with hinged cover, “LEGRAND Cat No. 35054 or tolier approved 150mm x 100mm PVC rectangular terminal/ junction box Weatherproof pvc termination/connection box (“Legrand” or other approved) Electro-galvanised steel metal enclosure for moulded case circuit breaker (MCCB) with cover gasket and screw-in knobs or hidden hinges with cam lock and 2 keys Electro-galvanised steel metal enclosure! box for minature circuit breaker (MCB) with hidden hinges, cam lock and 2 keys Approved metal box for 13 Amp socket outlet with hidden hinges, cam lock and 2 keys Camlock to metal box enclosure with 2 nos. keys


622.00 807.00 982.00 16.10 123.50 16.60 8.50 8.70 68.00 28.00 16.60 13.00

1

Q NOT IN USE

1

R LABOUR ONLY ITEM Contents SOR Page 1. Labour Only Item R1 - R5

SOR Page R

1

1

Item Description Unit Rate ($) R001 R002 R003 R004 R005 R006 R007 R008 R009 R010 R011

LABOUR ONLY ITEM * Labour only for carrying out the following works including reinstatement transport, equipment and establishment charges *(Ro0l R040) Replacing wiring for lamp holder Checking defective wiring, fuse, time switch, etc in switchroom/distribution by skilled electrician including repair where necessary in switch room/distribution board (Parts measured separately) Checking defective lamp pole wiring, fuse, including tracing fault & repair where necessary Refixing loosen lamp cover/fitting for post top lantern Dismantling single/double lamp post arm and dispose off site Fixing single/double arm bracket to lamp post (Parts measured separately) Repositioning single/double lamp post’s arm Replumbing verticality of lamp post not Pole 38.00 exceeding 5m height including excavation, casting new concrete footing (where necessary) painting of approved bituminous coating to surface of ground section of column up to 150mm above ground level and reinstate ground on completion Replumbing verticality of lamp post exceeding 5m but not exceeding 8m height including excavation, casting of new concrete footing (where necessary) painting of approved bituminous coating to surface of ground section of column up to 300mm above ground level and reinstate ground on completion Replumbing verticality of lamp post exceeding 8m but not exceeding l2m height including excavation, casting new concrete footing (where necessary) painting of approved bituminous coating to surface of ground section of column up to 300mm above ground level and reinstate ground on completion Tracing underground cable fault between two lamp poles or lamp post and switchroom for series of lamp posts in circuit (repair and parts measured seperately)

No. Job Pole No. Pole Pole Pole Pole Pole Pole Job

3.90 17.80 11.30 5.70 26.10 26.10 26.10 38.00 62.00 70.00 33.90

SOR Page R

2

2

R012 R013 R014 R015 R016 R017 R018 R019 R020 R021 R022 R023 R024 R025

Checking fitness of carpark lighting including dismantling the fitting, replacing parts where necessary (parts measured separately) cleaning fitting! diffuser and refixing on completion Refixing loose and fallen teak battens including replacement of wall plugs where necessary Refixing loose and fallen wiring/PVC trunking including supply of additional clips Refixing loose or fallen ceiling rose including the replacement of wood plugs where necessary Refixing meter/distribution board including the replacement of wood plugs where necessary Refixing loose electrical fittings and accessories including the replacement of wood plugs where necessary Removing existing ceiling rose and connecting short length of cable from existing lighting point directly into the existing light fittings inclusive of short length of cable, trunking/conduit and connector Refixing loose 20mm/2Smm diameter galvanised steel/pvc conduit pipes including new clip, saddle clamps and screws Checking and tightening the loose cable connection for fuses, MCCB’s and busbars in the main switchboard Checking and repairing to defective light in community hail, market, hawker centre or other parts of building exceeding 6m height including use of metal scaffolding (parts and fittings measured separately) Extra over item R02l for checking and repairing additional defective light within the same building including shifting of scaffolding (parts and fittings measured separately) Tracing fault in public lighting in building block including repair where necessary Checking, cleaning and tightening the 1st 5 nos. of loose neutral connector or line tap/line connector including replacement of defective screws (within same block) Checking, cleaning and tightening the remaining nos. of loose neutral connector or line tap/line connector in itme R025 including replacement of defective screws (within same block)

No. M M No. No. No. No. Job Job No. No. No. No. No.

8.90 0.90 0.90 1.00 9.70 2.80 4.25 4.40 17.50 26.20 6.30 5.65 2.30 1.40

SOR Page R

3

3

R026 R027 R028 R029 R030 R031 R032 R033

Dismantling and re-fixing illuminated Block No./Carpark Signages of vinyl/acrylic sheet on non-proprietary galvanised steel frame for the purpose of carrying out repair/replacement of defective fluorescent tubes, starters, ballasts etc (inclusive of metal scaffoldings not exceeding 6m height and parts and fittings measured separately) Modifying existing fluorescent light fitting for installation of electronic ballast or low loss ballast including supply of necessary wiring (Ballast measured seperately) Taking down, removing and refixing ceiling fans and regulators in new position not exceeding 200m distance (new fan point to be measured separately) Taking down, removing and refixing ceiling fans and regulators in new position exceeding 200m distance including transport (new fan point to be measured separately) Taking down wall fan in hawker centre or other parts of any building clean, oil, service & refix fan to original position after work completion Checking firmness of ceiling fan bracket/hook, taking down ceiling fans in hawker centres or other buildings as directed, dismantle the mechanical connecting components to check for worn boft/rivets, corroded hanging rod and bolt assembly without split cotter pins and replacing these parts (parts measured separately) if necessary, including cleaning fans and ref ixing on completion Servicing of air-circuit breaker (ACB) including provision of labour for the work - during office hour i.e. 8.00 am to 5.30 pm Servicing of additional air-circuit breaker within the same switchroom as item R032


8.50 5.50 10.10 15.50 11.35 13.10 450.00 350.00

SOR Page R

4

4

R034 R035 R036 R037 R038 R039

Servicing of air-circuit breaker (ACB) for work carry out after office hour or on Saturday, Sunday and Public Holiday Servicing of air-circuit breaker (ACB) including provision of generator for work carry out after office hour or on Saturday, Sunday and Public Holiday Servicing additional air-circuit breaker (ACB) within same switchroom for work carry out after office hours or on Saturday, Sunday and Public Holiday Servicing additional air-circuit breaker (ACB) within the same switchroom including provision of generator for work carry out after office hour or on Saturday, Sunday and Public Holiday Repairing fallen or loose lightning conductor and reset it to its original position including the use of securing material, additional clips, etc. (1 job refers to whole block/linkway/ gateway/pavilion/link building etc) Repositioning of existing light fittings and lighting point with new 3 x 2.Smrn2 PVC sheathed cable in new PVC trunking including removal of exising wiring and reinstatement (trunking run not exceeding 10m)

No. No. No. No. Job Point

650.00 850.00 550.00 700.00 24.25 28.00

1

S MISCELLANEOUS Contents SOR Page 1. Miscellaneous S1 — S2

SOR Page S

1

1

Item Description Unit Rate ($) S001 S002 S003 S004 S005 S006 S007 S008 S009 S010

* S. MISCELLANEOUS Supply and fix approved powered drive masonry pin including the use of cartridges Erection of double layer timber scaffolding including taking down after use (irrespective of height of building, a minimum of 5m width shall be paid)1M Erection of metal scaffolding not) exceeding 15m height including takir j down after use Erection of metal scaffolding exceeding l5m height but not exceeding 35m height including taking down after use Monthly rental rate for “Wildcat” self propelled work platforms Model 2032 with working height of 7.9Dm, overall length 2.30m, platforms capacity 800 Lbs including fuel and operator Supply and fix stainless steel screw (cyclindrical head) with washer to electro galvanise steel tap-off box cover including labour for drilling holes, forming screw tread and opening defective camlock Provide 300-450mm high concrete pedestal base for weatherproof/outdoor control box complete with mounting screws and brackets Supply and fix 25 mm2 to 70 mm2 earth wire tap 3 core l.5mm2 pvc/pvc flexible cable for fluorescent luminaire including connection to ceiling roses Tinned copper busbar including fixing accessories and connection

No. M2 M2 No. No. No. No. No. No. Kg

0.50 4.60 11.50 12.70 1552.00 3.70 40.60 8.30 1.00 18.40

SOR Page S

2

2

S011 S012 S013 S014 S015 S016 S017

Patch up openings for pipes/conduits exceeding 100mm dia but not exceeding 225mm dia. with waterproof cement and sand (1:3) mortar to wall and floor not exceeding 225mm thick and make good to match existing Hack through existing rc slab not exceeding 225mm thick to form opening not exceeding 0.03m2 for trunking and reinstate to match existing GS bracket for metal trunking fixed to ceiling or wall including ramset nails and 2 coats of painting Polarised 10 Amp rated plug and socket connector SV A.C. relay (MY2 or MY4) for aircraft warning lights consol box “CRI” electric insect killer 80W (2 x 40W UVBL) Model : 308 40W ultra violet tube for CR1 electric insect killer, mode/308

No. Opening No. No. No. No. No.

4.60 7.50 3.50 4.60 40.75 390.00 30.00

1

T EXCAVATION AND TRENCHING Contents SOR Page 1. Excavation T1 2. Demolition T1 3. Cover Plate T1 4. Turfing T1

SOR Page T1

1

Item Description Unit Rate ($) T001 T002 T003 T004 T005 T006 T007 T008 T009 T010

T. EXCAVATION AND TRENCHING EXCAVATION (Reinstatement of turf to be paid separately unless otherwise stated) Manual excavation of 300mm wide x 750mm deep trench for underground cable including sand bed and backfilling Mechanical excavation of 300mm wide x 750mm deep trench for underground cable including sand bed and backfilling Mechanical excavation of 600mm wide trench for underground cable not exceeding 750mm deep including sand bed and backfilling Mechanical excavation of 600mm wide trench for underground cable exceeding 750mm deep but not exceeding l:0m deep including sand bed and backfilling Excavate pit 1 m x 1 m x 750 mm deep and backfilling and reinstatement of turf DEMOLITION Breaking up macadam road surface 600mm wide and not exceeding 450mm thick for laying underground cable including taking up pitch block base and reinstate same on completion Breaking up reinforced concrete slab 600mm wide and not exceeding 150mm thick for laying underground cable lapping with new reinforcement on completion and reinstate to match existing Breaking up reinforced concrete drain (exceeding 300mm deep) and reinstate on completion to match existing COVER PLATE 1000 or 2000 x 150 x 2 mm thick UPVC cable cover plates as warning or protective cover in trench TURFING Supply and turf good quality 25mm thick cow grass in close turfing including 125mm thick top soil and well watering and tendering to ensure growth of turf

M M M M No. M M2 M M M2

3.60 3.00 5.20 8.15 24.90 15.70 26.70 82.90 3.70 2.90

1

U – DAYWORK

Contents SOR Page 1. Daywork Items U1 – U2

SOR Page U1

1

Item Description Unit Rate ($) U001 U002 U003 U004 U005 U006 U007 U008 U009 U010

U. DAYWORK Labourer for miscellaneous work Electrician Services rendered by licensed cable detection worker for site excavation using mechanical means for laying of underground cables/erection of lighting column for a minimum of 1 1/2 hours Injection test for 1 No. ACB/MCCB (with earth fault/overcurrent protection) by ENA registered testing engineer including submission of shutdown form to Powergrid Ltd, arrangement for shutdown etc for testing and providing temporary electrical supply and skilled electrician, equipment and transportation cost - during office hours i.e. 8.00 am to 5.30 pm Injection test for each additional circuit breaker (with earth fault/ overcurrent protection) within the same switchroom as item U004 Injection test for 1 No: ACB/MCCB (with earth fault/overcurrent protection) by EMA registered testing engineer including submission of shutdown form to Powergrid Ltd. arrangement for shutdown etc for testing and providing temporary electrical supply and skilled electricians, equipment and transportation cost - after office hours or on Saturday, Sunday and Public Holiday Injection test for each additional circuit breaker (with earth fault/overcurrent protection) within the same switchroom as item U006 Application and endorsement of Form CS/5 as licensed electrical worker when requested by Superintending Officer for SP Services Ltd testing for electrical extension/minor rewiring work for the electrical installation Supply of EMA Licensed Cable Jointer to carry out “Livefl termination of CTS cables at OG box Supply of PUB authorised small installation tester (ASIT) to test electrical extensions and submission of report to EMA/HDB

Hr Hr Hr No. No. No. No. Job Job Job

4.00 5.65 109.00 750.00 500.00 1000.00 750.00 142.50 142.50 100.00

1

SUPPLEMENTARY SCHEDULE OF RATES

SECTION XI - SUPPLEMENTARY SCHEDULE OF RATES

(I) SUPPLY AND DELIVERY ONLY

Preamble

The Contractor shall supply and deliver

(i) 600mm and 1200mm energy saving fluorescent tubes

(ii) starters for tubular fluorescent lamps operating on 50 Hz supply

(iii) 20 - 40W low loss ballast for fluorescent tube

(iv) 50 - 120W halogen lamp

(v) 13 - 18W/41 PLC lamp

(vi) 13 - 18W PLC ballast

to the respective Employer’s properties as and when directed by the Superintending Officer. The Contractor shall provide all necessary labour, materials, plants, equipments, tools, transportation and everything necessary, whether of a temporary or permanent nature for the manufacture, testing and delivery of the goods to the respective Employers properties as and when directed by the Superintending Officer


V00l

Supply and Delivery Items (V00l to V027) The following rates are nett rates with no addition/deduction for adjustment tà the Schedule of Rates Supply and deliver 600mm, 18W daylight fluorescent tube (Philips, Hitachi, Osram, Toshiba)

No

2.00

V002 Supply and deliver 900mm, 30W daylight fluorescent tube (Philips, Hitachi, Osram, Toshiba)

No. 2.30

V003 Supply and deliver 1200mm, 36W daylight fluorescent tube (Philips, Hitachi, Osram, Toshiba)

No. 2.50

V004 Supply and deliver 600mm, 18W warmwhite or cool white fluorescent tube (Philips, Hitachi, Osram, Toshiba)

No. 3.50


V005 900mm, 30W warmwhite or cool white fluorescent tube (Philips, Hitachi, Osram, Toshiba)

No. 3.90

V006 1200mm, 36W warmwhite or cool white fluorescent tube (Philips, Hitachi, Osram, Toshiba)

No. 4.30

V007 Starters for fluorescent lamps (Philips, Osram) No. 0.40

V008 Low loss 20W or 40W fluorescent ballast (ATCO, Helvar, Vossloh Schwabe)

No. 3.50

V009 Halogen lamp 12V 50W/120W (Osram, Philip, Thorn) No. 4.50

V0l0 Daylight/warm white compact fluorescent lamp PLC 13W (Philips, Osram, Splendour, Sylvania)

No. 5.50

V0l1 Daylight/warm white compact fluorescent lamp PLC 18W (Philips, Osram, Splendour, Sylvania)

No. 6.00

V012 Ballast for PLC lamp 13 — 18W (Philips, Schwabe, Helvar) No. 3.50

V013 6V, 3W indicating bulb for switchboard No. 1.00 V014 2D 16w 6000k tube, 4 pin, GE No. 14.40

V015 18w/41, OS bulb, Dulux D, Osram No. 7.15 V016 PL11/82 bulb, LYNX-S, Sylvania No. 2.95

V017 2D 16w 2700k tube, 2 pin, GE No. 14.40 V018 2D 28w tube 2700k 4 pin, GE No. 22.45

V019 10w fluorescent tube, Chiyoda No. 1.75 V020 8w fluorescent tube, Toshiba No. 1.85

V021 18w/11, OS bulb, Dulux D, Osram No. 6.35 V022 Par 38/120w bulb, fluorescent 30, Osram No. 6.90

V023 TLE40 54 tube, 40w circular, Philips No. 6.35 V024 TLD36w 54 tube, fluorescents, Philips No. 5.40

V025 2D 28w 3500k tube, 4 pin, GE No. 20.70 V026 150wIWDL bulb, metal Halide D/Enable Osram No. 47.15

V027 70w/WDL bulb, metal halide D/Ended Osram No. 46.00

(II) OTHER SUPPLEMENTARY RATES (V028 TO V063)

The preambles on Pages GP1 and GP2 for the standard schedule of rates shall be applicable for the following items. The following items will be subjected to the percentage adjustment to the SOR as indicated in the Form of Tender.


V028

Light Fittings (V028 to V036) Supply and install the following light fittings “SIEMENS” VEDO Avt 6801 luminaire c/w corrosion resistant die-cast aluminium fitting control gear and 80W mercury lamp

No. 227.00

V029 “TOPAZIO” ceiling light with ballast c/w 1 x PLC 18W lamp No. 95.00 V030 “SMERALDO” ceiling light with ballast c/w 2 x PLC 18W lamp No. 115.00

V031 “RIS PEND” pendant lamp with bamboo frame, paper diffuser, suspension cord set and 60/75/100w incandescent bulb

No. 20.00

V032 “ILMAS” OVALO CG/HG/OG/HV (IPSS) with powder coated die cast aluminium body, UV stabiised polycarbonate diffuser and 1 x 18w daylight/warmwhite PLC lamp

No. 86.80

V033 3 lamps 12V 50w halogen track light complete with 12V transformer No. 171.00 V034 Supply and install 6” globe light fitting c/w lamp No. 48.00

V035 “TRUBLITE” Die-cast Aluminium Bollard c/w glare louvre and 70W son lamp No. 380.00


V036 Supply & fix DD2 diffuser for FDL Light Fitting No. 138.00

Electrical Accessories/Fan/Cable (V037 to V055) Supply and install the following electrical accessories

V037 “SIEMENS” TH8200 hand-dryer No. 380.00 V038 “DEHN” overvoltage arrestor model VM280 No. 89.00

V039 “Soule” Surge arrestor PM15 15KA SP No. 260.00 V040 “Soule” Surge arrestor PM15 15KA TP No. 480.00

V041 Exhaust fan FV25AU6 10” diameter No. 70.00

V042 Grosvenor gold-plated flush 13A switch socket- outlets (single gang) for installation in boxes having a minimum depth of 35mm (MK)

No. 90.00

V043 Grosvenor gold-plated flush 13A switch socket- outlets (double gang) for installation in boxes having a minimum depth of 35mm (MK)

No. 150.00

V044 Supply & install of PDL 56 SW110 250V, 10A switch 150Hz, 1P66, Single Phase No. 60.00

V045

Metal clad split-load consumer control unit complete with 60A DP isolator 1 x 20A SP MCB, 40A DP ELCB with 7 x 5/20A 6KA SP MCB (AEB, MEM, SUNLIGHT)

No. 275.50

V046 32 Amp 4 pin weatherproof switch socket outlet No. 120.00 V047 Supply & install of 32A 4 pin plug top No. 65.00

V048 Supply & install of 40A 3 phase KWH Meter No. 276.00

V049 Supply and install 600 x 600 x 250mm metal enclosure with built-in lock, gasket, metal plate

No. 380.00

V050 3C x 2.5mm2 FR cable m 6.80 V051 4C x 2.5mm2 FR cable m 10.00

V052 Supply & install of 50mm galvanised cable tray m 4.60

V053 Supply and install FM/TV CATV or broadband socket outlet point complete with mounted pvc/metal mounting box

No. 48.00

V054 Supply & install telephone socket outlet point complete with moulded pvc/metal mounting box

No. 40.00

V055 Supply and install switchgear type 32A DP isolator complete with labelling, connecting cables / bars, bolts and nuts, etc

No. 165.00

V056

Neon Lightings Supply and install the following neon light fittings: 8mm to 15mm diameter neon tube comprising two electrodes, inclusive of dismantling and refixing the existing channel lettering

No.

150.00

V057 15KV, 30mA transformer for neon lights No. 260.00 V058 High tension cable or glass insolate cable m 50.00 V059

Power Point and Wiring (V056 to V063) One 13A switch socket outlet (1-gang) with wiring in 3 x 2.5m2 PVC sheathed cables including 40 x 20 (mm) PVC trunking and surface mounted white plate switchsocket outlet (trunking run not exceeding 12m)

No.

37.90

V060 One 13A switchsocket out (2-gang) with wiring in 3 x 2.5mm2 PVC sheathed trunking and surface mounted white plate switchsocket outlet (trunking run not exceeding 12m)

No. 44.90

V061 One 13A metal clad switchsocket outlet (1- gang) with wiring in 3 x 2.5mm2 PVC sheathed cables including 20mm diameter galganised steel conduits and metal clad switchsocket outlet (conduit run not exceeding 12m)

No. 64.30


V062 One 13A metal clad switchsocket outlet (1- gang) with wiring in 3 x 2.5mm PVC sheathed cables including 20mm dia PVC conduits and metal clad switchsocket outlet (conduit run not exceeding 12m)

No. 45.00

V063 One 15A switchsocket outlet (1-gang) with wiring in 3 x 2.5mm2 PVC sheathed cables including 40 x 20 (mm) PVC trunking and surface mounted white plate switchsocket outlet (trunking run not exceeding 12m)

No. 46.10

V064 One 15A metal clad switchsocket outlet (1- gang) with wiring in 3 x 2.5mm2 PVC sheathed cables including. 20mm dia galvanised steel conduits and metal clad switchsocket outlet (conduit run not exceeding 12m)

No. 69.00

V065 One 15A metal clad switchsocket outlet (1- gang) with wiring in 3 x 2.5mm2 PVC sheathed cables including 20mm diameter PVC conduits and metal clad switchsocket outlet (conduit run not exceeding 12m)

No. 49.50

V066

One 20A water heater point with wiring in 2 x 6mm2 PVC sheathed cable with 6mm2 PVC earth (green) cable including 40 x 20 (mm PVC trunking, surfaced mounted water heater switch (MARKED WATER HEATER AND WITH PILOT LAMP) and 20A connection unit (trunking run not exceeding 12m)

No. . .

65.40

V067 Air-Conditioning Supply labour, equipment and cleaning chemical to service fan coil unit of air- conditioning system including chemical wash where necessary

No. 53.33

V068 Supply labour, equipment and cleaning chemical to service condenser unit of air conditioning system including chemical wash where necessary

No. 80.00

V069 Supply labour and R22 refrigerant to re-charge compressor unit of air conditioning system

No. 33.33

V070 Attendance charge for servicing and maintenance of air conditioning system including transport to and from site

Trip 20.00

V071 Supply labour and equipment to temporarily remove single split air conditioning system including all existing cables, pipings, trunking etc and reinstall the same as directed by the Superintending Officer including and commissioning

No. 466.67

V072 Supply labour and equipment to temporarily remove double split air conditioning system including all existing cables, pipings, trunking etc and reinstall the same as directed by the Superintending Officer including and. commissioning

No. 666.67

V073 Supply labour and equipment to temporarily remove triple split A/C unit including all existing cables, pipings, trunking etc and reinstall the same as directed by the Superintending Officer including and commissioning

No. 1000.00

V074 Supply & install stainless steel support bracket for condenser unit of multi-split air conditioning system including temporary removal of condenser unit and removal of existing bracket if any

No. 160.00

V075 Supply & install of Emergency Call Bell with push-button or pull chord inclusive of notice stating “Emergency Call” complying with the code on Barrier Free Accessibility in buildings 2007

No 180.00

V076 Supply & install of call bell or buzzer outside the compartment complying with the code on Barrier Free Accessibility in buildings 2007

No 100.00

PA SOR for Electrical Works

Documents

Transcript of PA SOR for Electrical Works