P R E S E N T

SAS PRODUCTSA NEW TECHNOLOGY

We appreciate the opportunity to introduce you to our water based, (not petroleum or acid based), chemicals that dissolve the paraffin in crude oil and natural gas

All SAS chemicals are non-flammable, non-toxic, non-corrosive and entirely environmentally friendly

PRODUCTS TYPES :

1- SAS-A

2- SAS-B

3- SAS-C

SAS-A dissolves the paraffin in BS&W, (tank bottoms), in crude oil storage tanks and when blended with added fresh crude emulsifies it into a high grade saleable crude

It also lowers the sulfur content and NORM in the crude

After treatment, the tank is allowed to set for several hours and the water and sand will settle to the bottom and can be drained or pumped out thru the water draw valve

The rest is good marketable crude oil free of BS&W

SAS-A

Treating a crude storage tank with SAS-A eliminates the need to gas free the tank, cut a door sheet or the need to have personnel or equipment enter the tank

The treatment process can be completed in 7-10 days and the tank returned to service

When SAS-A is injected into the tank receipt line the result will be BS&W free crude and eliminating costly tank cleaning

Please refer to the test report from Dallas Laboratories and the accompanying letters of reference

SAS-A, CONT.

SLUDGE

ADD 5% TO 10% SAS AADD 150% TO 200% CRUDE

LET TANK SET FOR 4-12 HOURS

AGITATE VERY BRISKLY

LET TANK SET FOR 24 HOURS

INSTRUCTIONS PROCESS FOR TREATING TANK BOTTOM SLUDGE USING SAS-A

MARKETABLE CRUDE OIL

SANDWATER

STEP 1

STEP 5

STEP 2

STEP 3

STEP 4

STEP 6

SELL CRUDE

PUMP OUT WATER & SANDNow Tank Bottom is

100% clean

SAS-B is designed for down-hole treatment When introduced down-hole SAS-B will dissolve

the paraffin build up in submersible pumps, the production tube and the feeder line to the storage tanks

When introduced into the formation under pressure, SAS-B will dissolve the paraffin and allow the crude to flow more freely into the well reservoir

The result is a significant increase in production For continuous treatment both applications can

be achieved by adding a SAS injection system

SAS-B

IF YOU HAVE LOW OIL WELL PRODUCTION

DUE TO SLUDGE CLOSING PIPE CASING

LIKE THIS PHOTO

SAS B

SIMPLY INJECT SAS ‘B’ INTO WELL CASING ,,, SAS WILL EMULSIFY SLUDGE WITHIN FEW HOURS AND ALLOW SMOOTH FLOW OF

CRUDE GOING UP AS YOU SEE IN THE RIGHT GRAPHIC ANIMATION

OR LIKE THIS …SAS ‘B’ CAN INCREASE WELL PRODUCTION WITH SIMPLE PROCEDURE AND

IT IS SAFE FOR ALL TYPES OF PIPES AND

EQUIPMENTS

THE CASING PIPE WILL BE LIKE THIS AFTER INJECTING SAS ‘B’

OIL FLOW WILL INCREASE MORE THAN 30%

INJECT SAS ‘B’

SAS TO BE INJECTED INTO PIPE LINE UPSTREAM OF PRIMARY

AND TRANSFER PUMPS TO MIX AND BLEND SAS WITH THE

FLOWING CRUDE OIL

SAS PIPE LINE INJECTION PROCEDURE

SASPUM

P

BALL VALVE

BALL VALVE

THR’D-O-LET

SAS B

SAS B

SAS B

INSTALL SMALL TANK WITH

INJECTION PUMPOIL FLOW WILL INCREASE AND HAVE SLUDGE FREE

PIPE LINE

sludgesludg

e

PIPE LINE

PUMPCRUDE OIL

FLOW

SAS-C is designed for crude oil spill clean-up Soil that is contaminated with crude oil can

be excavated and washed with SAS-C The liquid residue can then be run thru an

oil/water separator

SAS-C

The water can be drained and the clean soil returned to its original location eliminating costly hauling and disposal in a hazardous waste landfill

The equipment can be mounted on a trailer or skid for mobility

SAS-C

SUMMARY

CONCLUSION..

Measure the quantity of the BS&W Determine (visually) the viscosity (thickness)

and liquidity of the sludge The thicker and drier the material the more

SAS will be needed to dissolve the paraffin Cover the BS&W with SAS-A v/v 5%-10%

depending on the thickness and liquidity of the BS&W

Add crude oil on top of the SAS-A v/v 150%-200% of the BS&W. SAS-A must be covered and or contained to prevent evaporation

Instructions for Treating BS&W (Tank Bottom Sludge) Using SAS-A

Let tank or vessel set for 4-12 hours to allow SAS to percolate down into the BS&W and begin to dissolve the paraffin.

After the paraffin is dissolved, begin to agitate all of the contents very briskly. The dissolved paraffin must be completely blended and mixed with the added crude. After the agitation process, allow to settle for several hours. Agitate mixture again until all of the paraffin is completely broken down and dissolved. If necessary, add more SAS and crude oil until desired results are achieved.

Instructions for Treating BS&W (Tank Bottom Sludge) Using SAS-A

Let tank set for several hours (preferably overnight). The sand and water will settle to the bottom and the rest will be good marketable crude

These instructions are valid weather in a large crude storage tank or a jar on a table

Prior to beginning treatment on a large tank, it is advisable to conduct a small test in a jar to obtain the optimum quantities of SAS and added crude oil.

After paraffin is dissolved and the sample is well blended, a 5% solution of water can be added on top of the crude oil. Let settle until all of the water goes to the bottom. This will significantly reduce the sulfur content in the treated crude.

Instructions for Treating BS&W (Tank Bottom Sludge) Using SAS-A

All SAS chemicals are blended in the USA by Tomco-Harwel Industries in Tulsa, Oklahoma They can be purchased in 55 gallon drums, 250-350 gallon totes and containerized in 20’ or 40’ containers. A 20’ container holds (20) 55 gallon drums, a 40’ container holds (60) 55 gallon drums

For more information: Please visit our website: www.tripledint.com for a demonstration

EQUIPMENTS FOR AGITATION

NO.. NEED ANY MORE

TurboMixerThe

By

The TurboMixer Advantage Passive Rotational System (Patent Pending) Automatic Rotation Center and Side Mount Capabilities Permanent or Temporary Installation No Moving Parts Through Shell or Roof Slow Rotation Speed Redundant Seals Built to Last

◦ Stainless Steel Construction◦ All Rotating Parts Slide on Thrust Bearings

Passive Rotational System

• Torque Generated By Offset Nozzles• Internal Viscous Controls Prevent Over Speed• Flow Field Customized by Replaceable Nozzles• Up to 175’ Cleaning Radius

Thrust Bearings Reduce Wear

Redundant Seals

TURBO MIXERS …. LAYOUT

THE REALITY – HOW DO THEY COMPARE

CURRENT SYSTEM PASSIVE ROTATIONAL SYSTEM

200 Feet Tank

TRIPLE D INTERNATIONAL INC. ARE THE

AUTHORIZED DEALER FOR KNIGHTHAWK TURBO MIXER IN ALL MIDDLE EAST AND AFRICA FOR ANY

INFORMATION OR QUERIES VISIT : WWW.KNIGHTHAWK.COM.

END OF PRESENTATIONTriple D International Incorporated

USA

All Rights Reserved

Thank you….