Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-20101 © Nokia Siemens Networks

Easy Guide for Installation ofFlexi System External OVP (FSES)3G NodeB

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-20102 © Nokia Siemens Networks

� Flexi System External OVP (FSES) Product Overview

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-20103 © Nokia Siemens Networks

Flexi System External OVP (FSES) Description

Flexi System External OVP (FSES) protects Flexi BTS modules against surge pulses in power feeding lines between System Module and RF Module.

FSES gives Class II (C, T2) protection for both common and differential mode disturbance for DC power feed between System Module and RF Module.

Protection level UP (differential i.e. Line – Line) < 500 V (at In, 8 / 20 µs).Protection level UP (common i.e. Line – Ground) < 1000 V (at In, 8 / 20 µs).

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-20104 © Nokia Siemens Networks

FSES Installation on the side 3U casing Flexi Modules

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-20105 © Nokia Siemens Networks

FSES Delivery Contents

The Flexi System External OVP (FSES) delivery contains the following items:� Flexi System External OVP (FSES) with a pre-installed power output and grounding cable.

� Plastic bag containing M5x8 screws (6150279) for fixing the FSES to a 3U casing.

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-20106 © Nokia Siemens Networks

FSES Electrical Interfaces

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-20107 © Nokia Siemens Networks

� Flexi System External OVP (FSES) Installation Process onto a 3U casing

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-20108 © Nokia Siemens Networks

� STEP 1:Check the Delivery with Delivery Contents for FSES in Packing List/SDR .

�Do not open the FSES. If opened, the warranty is void.

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-20109 © Nokia Siemens Networks

�STEP 2:Make sure the 3U cable entries have been installed.

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-201010 © Nokia Siemens Networks

�STEP 3:Install the FSES onto the module casing as shown in the below figure and fix with two screws.Tighten the screws to 2.0 - 2.5 Nm.Alternatively, you can connect the cabling first and then install the FSES ready-cabled.

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-201011 © Nokia Siemens Networks

�STEP 4:Connect the pre-installed grounding cable (994815) t o the plinth.

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-201012 © Nokia Siemens Networks

�STEP 5:Remove the FSES IP boot.

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-201013 © Nokia Siemens Networks

�STEP 6:When thick DC feeder cable is present, strip it for a length of about 10 cm (4 in) and wrap tape around the exposed wires in order not to break the IP boot.A thin DC feeder cable can be first inserted into the IP boot and then stripped and connected to the screw terminal.

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-201014 © Nokia Siemens Networks

�STEP 7:Insert the taped end of the DC feeder cable to the IP boot.When using a thick cable, the narrow end of the IP boot can be removed. Hold the IP boot by the rigid part and twist the end so that it comes off.

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-201015 © Nokia Siemens Networks

�STEP 8:Remove the tape ....

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-201016 © Nokia Siemens Networks

�STEP 9:Connect the wires to the screw terminal ....

Pay attention to the markings (V48N (-), V48RTN (+) and GND) on the FSES lid toensure correct polarity.

If you have a shielded DC cable, connect the shielding to the terminal marked with GND.Note that the FSES grounding cable has to be connected to the plinth.

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-201017 © Nokia Siemens Networks

�STEP 10:Fix the IP boot in place and fix the screw ....

Bend the IP boot to the side to make it easier to fix the screw.

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-201018 © Nokia Siemens Networks

�STEP 11:Fix the DC feeder cable to the cable entry with a c able tie.

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-201019 © Nokia Siemens Networks

�STEP 12:Depending on cable routing, fix the DC power cable and grounding cable to the cable entry with a cable tie.It is recommended that the DC power cable is routed down.

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-201020 © Nokia Siemens Networks

�STEP 13:If applicable, connect the alarm cable following the steps in next slidesAlarm output is Normally Open type.

An alarm cable is not included in the FSES delivery. Use an alarm cable that meets the

following requirements:• Minimum wire size 0.5 mm2

• Maximum wire size 2.0 mm2

• Round cable outer jacket diameter must be 8.3 +/- 0.5 mm2• Maximum currect 1.0 mA

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-201021 © Nokia Siemens Networks

A. Remove the alarm port IP boot.

Alarm Cable Installation process

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-201022 © Nokia Siemens Networks

B. Remove the IP plug from the IP boot.

Alarm Cable Installation process (Cont…)

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-201023 © Nokia Siemens Networks

C. Insert the alarm cable to the IP boot.

Alarm Cable Installation process (Cont…)

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-201024 © Nokia Siemens Networks

D. Connect the wires to the N.O. and Common terminals .

Alarm Cable Installation process (Cont…)

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-201025 © Nokia Siemens Networks

E. Fix the IP boot in place.

Alarm Cable Installation process (Cont…)

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-201026 © Nokia Siemens Networks

F. Connect the other end of the alarm cable either to the EAC port on the System Module front panel or to Flexi System Ex ternal Alarm (FSEB).

Alarm Cable Installation process (Cont…)

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-201027 © Nokia Siemens Networks

�STEP 14:Connect the ready-installed DC cable as required by your configuration :• System Module front panel: RF1/2/3 output port.• RF Module front panel: DC in port.Make sure that the IP boot is installed properly on the System Module or RF Module front panel.

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-201028 © Nokia Siemens Networks

�STEP 15:If applicable, install another FSES on top of the f irst one.Repeat steps 3 to 13.The maximum number of FSES in a stack is two.

Soc Classification level Abhijit Roy\Ver 0.1 / 12-July-201029 © Nokia Siemens Networks

Thank You