Overview of Wire Compensation

for the LHC

Jean-Pierre Koutchouk

CARE-HHH Meeting on beam-beam effects and beam-beam compensation

CERN 08/28/2008

Outline

1.Motivation for wire compensation in the nominal LHC

2. Motivation for wire compensation for the LHC Upgrade(s)

3. Principle of wire compensation (LHC)

4. Compensation efficiency: simulations, experiments, operations

5.Conclusions

1- Motivations for nominal LHC

1. The nominal machine performance is limited by the long-range beam-beam effect, with constraints on the Xing planes.

2. The crossing angle had already once to be increased from 200 to 300 rad (footprint to dynamic aperture); its margin seems small (tight control necessary during operations).

3. chaotic particle trajectories at 4-6 due to long-range; beam-beam effect: lifetime? background? collimation?

(modest) recovery of some of the ~15% geometric luminosity loss from crossing angle

Investigations of the beam-beam effect severity well before the nominal beam current is reached.

2- Motivation for the LHC Upgrade

The crossing angle has to be significantly increased with a large loss of luminosity the reduction of β* the increased bunch current and number of bunches the possibly increased interaction length (longer

quadrupoles)

0.1 0.2 0.3 0.4 0.5m

1

1.5

2

2.5

3

3.5

4

ler.

ytisonimul

Effect of crossing angle versus at nominal current

Luminosity increase vs beta*:

1. no Xing angle,

2. nominal Xing and bunch length,

Motivation for the LHC Upgrade

Wire compensation has the potential to:

• minimize the required increase in crossing angle (and quad aperture) and corresponding rapid loss in luminosity.

• compensate all LRBB’s at large enough separation, leaving more freedom to keep a few at reduced separation (D0 scheme; cf Guido’s talk).

3- Principle of Wire Compensation

Proposed in 2000.Either side of IP1 and IP5.H crossing: wires BETWEEN the beamsV crossings: wires above or below the beams

Location of the Correctors

104.931m from the IP’s, in front of the TAN absorber.ECR: LHC-BBC-EC-0001, EDMS503722, Oct. 2004

for future wire beam-beam compensators - “BBLRs” -, 3-m long sections have been reserved in LHC at 104.93 m(center position)on either side of IP1 & IP5 in 2004

4 Compensation Efficiency4a Simulations

Several generation of mostly weak-strong, but as well strong-strong simulations since 2000:• JPK• Zimmermann• Shi, Jin & Herr (strong-strong)• Dorda

With consistent conclusions:• compensation very “efficient” (footprint, dynap)• compensation robust (need not be exact)• intensity noise shall be under control (FZ: <0.1%; J. Shi: <0.5%; TEV elens < 1% in practice, with less current but less distance)

1- Footprint compression (U. Dorda):

2- Dynap gain: 1.5 to 2 sigma (U. Dorda)

U. Dorda: dynap versus compensating current for nominal and extreme pacman.

Even though a pulsed wire compensation should be the final goal, a first generation of simple dc wire compensation is worth considering.

4b- Efficiency in beam tests

SPS experiment 2004:two wires model beam-beam compensation2.6 degree phase shift

1 wire

2 wires

no wire

vertical tune

beam lifetime

lifetime is recovered over a large tune range, except for Qy<0.285

Qx=0.31

MD 02.09.2004

178390 178400 178410 178420 178430 178440 178450cycle number

1000

2000

3000

4000

5000

6000

7000

emitefilnis

Lifetime versus cycle number

compensation

excitation

no beam beam

Nominal LHC tunes, 26 GeV

Other SPS and RHIC experiments & studies

Several other experiments have been carried out at the SPSand at RHIC, since wires were installed. Their goal has been toinvestigate the strength of the long-range beam-beam interaction rather than the compensation (so far in RHIC). A good understanding of the perturbation is indeed a key step towards its compensation. They have as well demonstrated the required reliability of the instrument.

Clearly, RHIC has a high potential to advance the understanding of (simulated) long-range beam-beam encounters , given its long beam lifetime, observation time and precision instrumentation… More MD time would be very useful.

A wire was installed “in” Dafne to compensate the long-range beam-beam interaction.C. Milardi et al, 2008.Long-range beam-beam interactions (parasiticcrossings) were one of the main luminosity performancelimitations for the lepton Φ-factory DAΦNE in itsoriginal configuration. In particular, the parasiticcrossings led to a substantial lifetime reduction of bothbeams in collision. The wires installed in the DAΦNE IRs proved to be effective in reducing the impact of BBLR interactions andimproving the lifetime of the positron beam especiallyduring the KLOE run.

4c- Efficiency in Operations

Conclusions

1. By beam-beam standards, the efficiency of the

compensation of the long-range beam-beam effect appears well established.

2. It has given concrete improvement in Dafne.

3. The compensation has a potential both for the nominal and upgraded LHC. In addition, it would allow early and efficient studies of one of the most difficult and limiting phenomenon in the LHC.

4. The implementation of a first dc solution should be relatively simple and of limited cost.

5. It appears timely to consider an implementation plan.