Overview of U.S. Mattress Requirements - CPSC.gov
Transcript of Overview of U.S. Mattress Requirements - CPSC.gov
![Page 1: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/1.jpg)
U.S. Consumer Product Safety Commission
This presentation was prepared by CPSC staff, and has not been reviewed or approved by, and may not necessarily reflect the views of, the Commission.
Overview of U.S. Mattress RequirementsJacqueline Campbell
MARCH 2018
This presentation was prepared by CPSC staff, has not been reviewed or approved by, and may not reflect the views of the Commission.
![Page 2: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/2.jpg)
The slides in this presentation are intended to be used in a training event with verbal elaboration by a knowledgeable presenter. The slides highlight key U.S. product safety requirements for this discussion. The text is not a comprehensive statement of legal requirements or policy and should not be relied upon for that purpose. You should consult official versions of U.S. statutes and regulations, as well as published CPSC guidance when making decisions that could affect the safety and compliance of products entering U.S. commerce. Note that references are provided at the end of the presentation and a handout on phthalates prohibitions in children’s toys and child-care articles is also available.
2
![Page 3: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/3.jpg)
Topics
• What Is a Mattress?• U.S. Mattress Requirements
– Flammability, Labeling, and Recordkeeping– Certification– Chemical Content– Tracking Labels
• Designing for Safety• CPSC Mattress Resources
![Page 4: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/4.jpg)
What Is a Mattress?
• Regulatory Definitions and Scope:– A mattress is:
• A ticking filled with a resilient material used alone or in combination with other products intended or promoted for sleeping upon, including mattresses that have undergone renovation.
• Subject to both 16 C.F.R. parts 1632 and 1633.
– A mattress pad is:• A thin, flat mat or cushion, or ticking filled with resilient
material for use on top of a mattress.• Subject to 16 C.F.R. part 1632 only.
![Page 5: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/5.jpg)
What Is a Mattress?• The definition of mattress includes (but is not
limited to):– Traditional mattresses, in all sizes, with flat or pillow
top, single or double sided– Crib mattresses– Futons– Mattresses in sleeper sofas and campers– Water bed and air mattresses
• If they contain upholstery material between the ticking and mattress core
• Otherwise, exempt from requirements• See §§1632.1(a) or 1633.2(a)-(c) or contact CPSC
Compliance staff for more information
![Page 6: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/6.jpg)
U.S. Mattress Requirements• Flammable Fabrics Act (FFA)
– Mattresses and Mattress Pads– Mattress Sets
• Federal Hazardous Substances Act (FHSA)– Lead Content
• Consumer Product Safety Act (CPSA)– Limitation on levels of Lead in Paint and Surface
coatings– Limitation on limits of certain Phthalate Content – Certification Requirements– Tracking Labels
![Page 7: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/7.jpg)
Flammable Fabrics Act (FFA)
• Primary authority for CPSC-regulated textiles• Focused on flammability performance• Regulations
– General wearing apparel (16 CFR part 1610)– Vinyl plastic film (16 CFR part 1611)– Children’s sleepwear (16 CFR parts 1615/1616)– Carpets and rugs (16 CFR parts 1630/1631)– Mattresses and mattress pads (16 CFR part 1632)– Mattress sets (16 CFR part 1633)
![Page 8: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/8.jpg)
Flammable Fabrics Act (FFA)
• Standard for the Flammability of Mattresses and Mattress Pads (16 CFR part 1632)– Applies to both mattresses and mattress pads– Cigarette ignition test
• Standard for the Flammability (Open-Flame) of Mattress sets (16 CFR part 1633)– Applies to mattress sets (mattress alone or with
foundation)– Open-flame ignition test
For mattresses, both standards must be met before the product can be entered into commerce in the U.S.
![Page 9: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/9.jpg)
• Purpose of Regulation (1973)– To improve ignition resistance of mattresses and
mattress pads to smoldering cigarettes
• Uses prototype testing scheme– A design that is the same as production units with
respect to materials, components, design, and method of assembly.
– New prototypes and material changes require testing
• Substitution tests exist for some material changes
Mattresses and Mattress Pads
![Page 10: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/10.jpg)
• 6 surfaces (interim policy covering 2 surfaces)
• Test design features– Smooth surface, tape edge, quilting
or tufting• Bare and with sheeting (2 layers)• SRM cigarette ignition source
– Total of 36 observations for interim testing policy
• 18 locations on each test specimen• 9 locations on each of bare and
sheeting
Mattresses and Mattress Pads
![Page 11: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/11.jpg)
Mattresses and Mattress Pads
![Page 12: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/12.jpg)
Mattresses and Mattress Pads
• Test criteria: Charring may not extend greater than 2 inches in any direction from the ignition cigarette
![Page 13: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/13.jpg)
Mattresses and Mattress Pads
• Labeling Requirements– Date of manufacture (MM/YYYY)– Manufacturing location
• Include all company manufacturing locations by street address
– If a FR treatment is used:• Mark with “T”.• Include precautionary care instructions to maintain
FR efficacy.
*Note that there may be additional state requirements for labeling.
![Page 14: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/14.jpg)
• Recordkeeping Requirements– Manufacturing specifications and
descriptions– Test details and results– Photographs (before and after testing)– Other information in §1632.31(c), as
applicable– Must be maintained while prototype is in
use and for 3 years after
Mattresses and Mattress Pads
![Page 15: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/15.jpg)
Mattresses and Mattress Pads
![Page 16: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/16.jpg)
• Purpose– To limit fire intensity– To increase time for discovery and escape
by preventing or delaying flashover
• Effective in 2007• Uses prototype testing scheme
Mattress Sets
![Page 17: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/17.jpg)
• Number of tests depends on stage of prototype tested
• Prototype/test as intended to be used– Mattress alone– Mattress and foundation
• Open flame ignition source– Pair of gas burners
• Top surface ignited for 70 seconds• Side surface ignited for 50 seconds
– Ignition source intended to approximate burning bedclothes on a mattress
• Performed under an instrumented hood
Mattress Sets
![Page 18: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/18.jpg)
Mattress Sets
![Page 19: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/19.jpg)
0
200
400
600
800
1000
1200
1400
1600
1800
• Test Criteria:– Test lasts 30
minutes– Total heat release
may not exceed 15 MJ in first 10 minutes of test
– Peak heat release rate may not exceed 200 kW
Mattress Sets
![Page 20: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/20.jpg)
• Qualified Prototype– Initial design tested according to §1633.4(a) that
meets flammability requirements– Minimum of 3 consecutively tested specimens– Any failures disqualify prototype
• Confirmed Prototype– Same as qualified prototype– Minimum of 1 test per manufacturing location– Intended to check manufacturing and confirm same
as qualified • Subordinate Prototype
– Some limited differences allowed from qualified or confirmed prototypes
– No testing required
Mattress Sets
![Page 21: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/21.jpg)
• Purpose of prototype scheme– Lower testing burden by using a qualified prototype
on which confirmed or subordinate prototypes can be based, also called prototype pooling
• Qualified/confirmed vs. subordinate – Mattress size– Ticking– Other components that are not expected to change
flammability performance based on reasonably objective criteria
• Reasonably objective criteria– Evidence-based, demonstrable
Mattress Sets
![Page 22: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/22.jpg)
Mattress SetsFactory A
Factory BMattress Design
Qualified Prototype
Subordinate Prototype
Subordinate Prototype
Subordinate Prototype
Confirmed Prototype
Subordinate Prototype
Subordinate Prototype
![Page 23: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/23.jpg)
Mattress SetsFactory A
Factory BMattress Design
Qualified Prototype
Subordinate Prototype
Subordinate Prototype
Subordinate Prototype
Confirmed Prototype
Subordinate Prototype
Subordinate Prototype
3 Tests1 Test
![Page 24: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/24.jpg)
Mattress SetsLabeling: Mattresses
![Page 25: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/25.jpg)
Mattress SetsLabeling: Foundations
![Page 26: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/26.jpg)
• Recordkeeping Requirements– Test records
Test results, video, pictures– Prototype records
Unique IDs, detailed description of components and manufacture, models and production lots, subordinate prototypes
– Pooling (Confirmation) records– Quality Assurance records
Procedures, production test records, production lot– Must be maintained while prototype is in use and for 3
years after – All records must be maintained in English in the U.S.
See §1633.11 and https://www.cpsc.gov/Business--Manufacturing/Business-Education/Business-Guidance/Mattresses/Suggested-Recordkeeping-Forms-
for-16-CFR-1633/ for more information
Mattress Sets
![Page 27: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/27.jpg)
Mattress Sets
![Page 28: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/28.jpg)
• General Use Product– General Certificate of Conformity (GCC)– Does not require third party testing
• Children’s Product– Children’s Product Certificate (CPC)– Requires third party testing by a CPSC-accepted laboratory
for all regulations to which the product is subject– Applies to crib and children’s mattresses and mattress pads
Issued by manufacturer (if domestic) or importer of record. An importer can rely on testing performed by a manufacturer to issue
a certificate as long as due care is exercised and all CPSC requirements are met.
Certification Requirements
![Page 29: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/29.jpg)
Certification Requirements• Testing for general use products
– A test of each product or a reasonable testing program
• Testing for children’s products– Must be performed by a CPSC-accepted laboratory
https://www.cpsc.gov/cgi-bin/labsearch/– Stages of Testing
• Initial certification (Prototype)• Material change/Component part• Periodic (§1107.21)
– At least once a year with a periodic test plan– Every 2 years with a production testing plan– Every 3 years with ongoing testing by an ISO/IEC 17025:2005(E)
laboratory
![Page 30: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/30.jpg)
For crib and children’s mattresses and mattress pads:• Lead Content (FHSA)
– Products designed and intended primarily for children 12 years or younger
– Concentration may not exceed 100 ppm• Lead in Paint and Surface Coatings (CPSA)
– Products designed and intended primarily for children 12 years or younger and some general use furniture
– Concentration may not exceed 90 ppm• Phthalate Content (CPSA)
– Children’s toys and child care articles (products used to facilitate sleeping and feeding for children 3 years or younger)
– Only certain phthalates– Concentration may not exceed 0.1 %
Third party testing by a CPSC-accepted laboratory is required
Chemical Content Requirements
![Page 31: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/31.jpg)
For crib and children’s mattresses and mattress pads:• For products designed and intended primarily
for children 12 years or younger, a permanent, distinguishing mark (tracking label) must:– Be affixed to the product and its packaging, and – Provide certain identifying information.
• The existing required mattress labeling meets this requirement (mattress pads may not).
Tracking Label Requirements
![Page 32: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/32.jpg)
• Know and comply with all applicable safety requirements.
• Conduct required testing (or exercise due care in accepting test results from another party).
• Maintain consistent procedures and retain records.• Monitor components and suppliers.• Confirm materials and component specifications .• Maintain consistent methods of assembly.• Report problems early.
Include safety in your product design from the beginning of your manufacturing or sourcing process.
Designing for Safety
![Page 33: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/33.jpg)
• Mattress Information Pagehttps://www.cpsc.gov/Business--Manufacturing/Business-Education/Business-Guidance/Mattresses(English) https://www.cpsc.gov/s3fs-public/pdfs/blk_pdf_mattqa.pdf(Chinese) https://www.cpsc.gov/s3fs-public/pdfs/blk_pdf_openflame_ch.pdf
• Regulations1632 http://www.ecfr.gov/cgi-bin/text-idx?SID=59ceb81a60d382bcc84bf00de2828ad9&node=16:2.0.1.4.98&rgn=div51633 https://www.ecfr.gov/cgi-bin/text-idx?SID=80fb5cb965175b6f41f2637cf585bad1&mc=true&node=pt16.2.1633&rgn=div5
• Laboratory Manuals1632 https://www.cpsc.gov/s3fs-public/pdfs/blk_media_testmatt.pdf1633 https://www.cpsc.gov/s3fs-public/pdfs/blk_media_labmanual.pdf
• Recent Mattress Webinar (September 2017)https://www.cpsc.gov/Newsroom/Video/cpsc-small-business-office-webinar-series-mattresses
CPSC Mattress Resources
![Page 34: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/34.jpg)
CPSC Manufacturing Resources
https://www.cpsc.gov/s3fs-public/pdfs/blk_pdf_HandbookforManufacturing.pdf
http://www.cpsc.gov//Global/Business-and-Manufacturing/Business-Education/RegulatedProductsHandbook.pdf
![Page 35: Overview of U.S. Mattress Requirements - CPSC.gov](https://reader033.fdocuments.in/reader033/viewer/2022043013/626b69614d89a661905d33f4/html5/thumbnails/35.jpg)
Contact Information
Lisa ScottFire Protection Engineer
Directorate for Laboratory Sciences
Office of Hazard Identification and Reduction301-987-2064
Justin JirglCompliance Officer
Regulatory Enforcement DivisionOffice of Compliance and Field Operations
Jacqueline CampbellSenior Textile Technologist
Directorate for Engineering Sciences
Office of Hazard Identification and Reduction301-987-2024
www.CPSC.gov
U.S. Consumer Product Safety Commission