OVERALL DISPLAY SIZE DETAIL C SECTION 101 GP4-AAAxBBB …
1
28' 1-3/16" [8565 ] OVERALL WIDTH 9' 10-3/16" [3002 ] OVERALL BTM SECTION 8' 7-13/16" [2637 ] OVERALL TOP SECTION 18' 6" [5639 ] OVERALL HEIGHT 18' [5486 ] ACTIVE HEIGHT 27' 7-3/16" [8412 ] ACTIVE WIDTH 14' 4-13/16" [4389 ] DISTANCE BETWEEN LIFTLUGS. SEE INSTALL NOTES #1, #2, AND #3. 11-1/16" [282 ] 2-3/16" [56] CLEARANCE NEEDED FOR HOODS AND QUICK CONNECTS 1' 4-5/16" [415 ] 2-1/2" [64] 1-13/16" [45] TYPICAL HOOD DEPTH 2-1/2" [64] 8" [203 ] SEE INSTALL NOTE #11 1" [25] TYPICAL FOR ALL T-CLIPS 2" [51] MTG HOLE SPACING @2 2" [51] MTG HOLE SPACING @3 4-1/16" 104 [ ] TOP OF STEEL DIMENSIONS 0" 0 [] 9' 10-1/16" 2998 [ ] 18' 1-9/16" 5527 [ ] 2' 8-7/8" [835 ] TYP. PER LARGE HOOD 5-1/4" [133 ] DISTANCE BETWEEN TOP OF HOOD AND BTM OF T-CLIP 4" [102 ] DISTANCE BETWEEN TOP OF HOOD AND BTM OF T-CLIP 9-13/16" 250 [ ] 0" 0 [] 2' 11/16" 627 [ ] 8' 8-15/16" 2665 [ ] 10' 5-1/16" 3176 [ ] 11' 7-7/8" 3553 [ ] 17' 1-3/4" 5226 [ ] 18' 6-3/16" 5643 [ ] 10-5/16" 261 [ ] 0" 0 [] 6" MAX 14' 13/16" 4287 [ ] 22' 5/16" 6714 [ ] 6" MAX 24' 6-13/16" 7488 [ ] 27' 3-1/16" 8308 [ ] 28' 1-3/8" 8569 [ ] 1' 7-1/16" 485 [ ] 2' 2-3/4" 679 [ ] 2' 11/16" 627 [ ] 11' 7-7/8" 3553 [ ] SEE INSTALL NOTE #11 4" [ 102 ] 6" MAX 3' 6-13/16" 1087 [ ] 1' 6-11/16" [475 ] TYP. PER SMALL HOOD # DETAIL DESCRIPTION 1 DISPLAY GP4-AAAxBBB-CC (SEE CHART IN TOP LEFT CORNER) 2 LED COLOR RGB 3 ACTIVE AREA 18' [5486 ] X 27' 7-3/16" [8412 ] 4 OVERALL SIZE 18' 6" [5639 ] X 28' 1-3/16" [8565 ] 5 CABINET ALUMINUM 6 VENTILATION REAR INTAKE & EXHAUST 7 ACCESS SERVICE FROM FRONT OF DISPLAY 8 WEIGHT SECTION 101: 2695 LBS [ 1222 KG] (APPROX) SECTION 201: 3075 LBS [ 1395 KG] (APPROX) TOTAL: 5780 LBS [ 2622 KG] (APPROX) 9 SHIPPING SHIPPED IN TWO SECTIONS. ASSEMBLY OF SECTIONS IS REQUIRED ON-SITE 10 DIMENSIONS FEET AND INCHES [MILLIMETERS] STRUCTURAL RATING 1 DESIGN WIND PRESSURE "P" (CASE A) P<= 97 PSF 2 STANDARD/CODE IBC 2009/ASCE7-05 3 MINIMUM STRINGER DIMENSION HSS 4" X 4" X 3/16" 4 MAXIMUM CLIP ANGLE SPACING 10' 6" [3200 ] 1' MAX POWER RATING PER SINGLE FACE: FOR SIZING ELEC.SERVICE MAX REQ'D SHOWN MOD GRID SECTION MAX WATTS 120/240VAC 1PH 60Hz (3 WIRES + GND) DOMESTIC 240VAC 1PH 50Hz (2 WIRES + GND) INTERNATIONAL SPECIAL ORDER LINE 1 AMPS LINE 2 AMPS LINE 1 (AMPS) 7 X 23 SECTION 101 10408 46.36 40.38 43.37 8 X 23 SECTION 201 11799 46.36 51.97 49.16 15 X 23 TOTAL 22207 92.72 92.35 92.53 VENTILATION REQUIREMENTS 1 DISPLAY RELIES ON VENTILATION TO FUNCTION PROPERLY. VENTILATION HOODS, LOCATED AT THE BACK OF THE DISPLAY, MUST BE ABLE TO DRAW IN AIR AT A TEMPERATURE NO GREATER THAN 120°F 2 AIRFLOW AT AMBIENT TEMPERATURE CAN BE MAINTAINED BY PROVIDING OPENINGS FOR INTAKE (AT THE BOTTOM) AND EXHAUST (AT THE TOP) BEHIND THE DISPLAY. A MINIMUM OF 16.0 SQFT FOR INTAKE AND 16.0 SQFT FOR EXHAUST IS REQUIRED. IF THE OPENINGS CANNOT BE PROVIDED AS STATED, USE WALL MOUNT PROPELLER FANS TO GENERATE A MINIMUM OF 4800 CFM OF AIRFLOW ACROSS THE BACK OF THE DISPLAY. 3 VENTILATION INTAKES ARE FILTERED. FILTERS ARE ACCESSIBLE FROM FRONT AND WILL NEED TO BE PERIODICALLY CLEANED IN ORDER TO PROVIDE PROPER VENTILATION. REFER TO MAINTENANCE SCHEDULE FOR THE RECOMMENDED CLEANING SCHEDULE INSTALL NOTES 1 WHEN LIFTING USE ALL LIFTLUGS AND MAINTAIN AN ANGLE LARGER THAN 55° BETWEEN THE CABINET AND LIFTING DEVICE. 2 1-1/16" LIFTLUG DIAMETER TO ASSIST WITH DISPLAY INSTALLATION. MAX WIND SPEED DURING INSTALLATION MUST BE LESS THAN 20 MPH. 3 LIFTLUGS MAY NOT BE USED FOR PERMANENT INSTALLATION. 4 DISPLAY WILL BE SHIPPED WITH SOME TOP BORDER COVERS REMOVED. COVERS WILL NEED TO BE ATTACHED WITH INCLUDED HARDWARE AFTER DISPLAY IS MOUNTED TO STRUCTURE. 5 GROUND LUG FOR GROUND CONNECTION. ALL SECTIONS NEED TO BE GROUNDED. 6 2" MEYERS HUB FOR POWER TERMINATION TO INTERNAL LOAD CENTER. SEE POWER RATINGS ABOVE. 7 SIGNAL INPUT AT QUICK CONNECT. PRIMARY/SINGLE FACE DISPLAY SHOWN. SEE CLEARANCE DIMENSION ON LEFT SIDE VIEW. 8 TWO 1/2" CONDUIT KNOCKOUTS FOR OPTIONAL SIGNAL ENTRANCE. 9 DISPLAY WILL BE PAINTED SEMI-GLOSS BLACK ON FRONT AND SIDE PERIMETER WITH MILL FINISH ALUMINUM ON REAR OF DISPLAY. 10 MECHANICAL AND SIGNAL CONNECTIONS OCCUR EXTERNAL TO DISPLAY. 11 T-CLIPS FOR MOUNTING.T-CLIPS CAN BE ADJUSTED VERTICALLY 1/2" AS NEEDED DURING INSTALLATION. T-CLIPS CAN BE WELDED OR BOLTED TO STRINGER AT A MAX DISTANCE 2-1/2". SEE DETAILS C & D. 12 DAKTRONICS IS NOT RESPONSIBLE FOR THE MOUNTING HARDWARE OR THE INTEGRITY OF THE MOUNTING STRUCTURE. 13 DAKTRONICS IS NOT RESPONSIBLE FOR THE MAIN ELECTRICAL DISCONNECT. SEE POWER RATINGS ABOVE. 14 FOR MORE INSTALLATION DETAILS AND GUIDELINES REQUEST DD-1954173 FROM YOUR DAKTRONICS REPRESENTATIVE PIXELS HIGH (AAA) PIXELS WIDE (BBB) PIXEL SPACING (CC) MAX WATTS 330 506 16MM 22207 270 414 20MM 20201 210 322 26MM 19399 PIXELS HIGH (AAA) PIXELS WIDE (BBB) PIXEL SPACING (CC) 176 506 16MM 144 414 20MM 112 322 26MM PIXELS HIGH (AAA) PIXELS WIDE (BBB) PIXEL SPACING (CC) 154 506 16MM 126 414 20MM 98 322 26MM REV DATE: BY: DAKTRONICS, INC. THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THIS DRAWING ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY ANY MEANS WITHOUT THE EXPRESSED WRITTEN CONSENT OF DAKTRONICS, INC. COPYRIGHT 2011 DAKTRONICS, INC. BROOKINGS, SD 57006 DO NOT SCALE DRAWING PROJ: GALAXYPRO GP4 SERIES TITLE: SHOP DWG, GP4, 18' 6''x28' 2'' (15x23 MODS) DESIGN: TWHITEH DRAWN: RBASSET DATE: 28-NOV-12 SCALE: 1=100 SHEET: REV JOB NO: FUNC-TYPE-SIZE 1120368 1 OF 1 00 P 1630 E - 10 - B OVERALL DISPLAY SIZE GP4-AAAxBBB-CC DAKTRONICS LIGHT SENSOR (DO NOT BLOCK) SECTION 101 GP4-AAAxBBB-CC SECTION 201 GP4-AAAxBBB-CC FRONT VIEW SIGNAL INTERCONNECT SEE INSTALL NOTE #10 SIGNAL INTERCONNECT SEE INSTALL NOTE #10 PORTIONS OF TOP BORDER COVERS ARE REMOVED. FOR CLARIFICATION SEE INSTALL NOTE #4. SIGNAL INTERCONNECT SEE INSTALL NOTE #10 PRIMARY SIGNAL INPUT QUICK CONNECT. SEE INSTALL NOTE #7 OPTIONAL SIGNAL ENTRANCE SEE INSTALL NOTE #8 INTAKE HOOD, SEE VENTILATION NOTES #1, #2, AND #3. EXHAUST HOOD SEE VENTILATION NOTES #1 AND #2 POWER ENTRANCE SEE INSTALL NOTE #6 GROUND LUG. SEE INSTALL NOTE #5. REAR VIEW MILL FINISH ALUMINUM REAR OF DISPLAY SEE INSTALL NOTE #9 SEE DETAIL A SEE DETAIL B LEFT SIDE T-CLIPS. SEE DETAILED VIEWS C & D. SEE INSTALL NOTE #11 USE A GALVANIZED OR WEATHER PROTECTED 5/8" BOLT (MIN ASTM A325), WASHERS (MIN ASTM F436), AND NUT (MIN ASTM A563) OR WELD. SEE WELD SPECIFICATIONS ON DETAIL D. DETAIL C TOP AND BOTTOM T-CLIPS SEE INSTALL NOTE #11 (TUBE SHOWN FOR CONCEPT ONLY) SCALE 1/20 SEE HARDWARE SPECIFICATIONS ON DETAIL C DETAIL D SPLICE T-CLIPS SEE INSTALL NOTE #11 (TUBE SHOWN FOR CONCEPT ONLY) SCALE 1/20 ALL WELDING SHALL BE PERFORMED BY A WELDER CERTIFIED FOR THE SPECIFIED TYPE AND POSITION OF THE REQUIRED WELD. ALL WELDING SHALL BE IN ACCORDANCE WITH AWS 01.1. SHIELDED METAL ARC WELDING PROCESSES SHALL BE USED TO PERFORM WELDS WITH A LOW HYDROGEN E70 SERIES ELECTRODE. DETAIL A SCALE 1/20 DETAIL B SCALE 1/20 3 SIDES 1/4" 3 SIDES 1/4"
Transcript of OVERALL DISPLAY SIZE DETAIL C SECTION 101 GP4-AAAxBBB …
28' 1-3/16" [8565 ]OVERALL WIDTH
9' 10-3/16" [3002 ]OVERALL BTM SECTION
8' 7-13/16" [2637 ]OVERALL TOP SECTION
18' 6" [5639 ]OVERALL HEIGHT
18' [5486 ]ACTIVE HEIGHT
27' 7-3/16" [8412 ]ACTIVE WIDTH
14' 4-13/16" [4389 ]DISTANCE BETWEEN
LIFTLUGS. SEE INSTALLNOTES #1, #2, AND #3.
11-1/16"[282 ]
2-3/16" [ 56 ]CLEARANCE NEEDEDFOR HOODS ANDQUICK CONNECTS
1' 4-5/16"[415 ]
2-1/2" [ 64 ]
1-13/16" [45 ]TYPICAL HOOD DEPTH
2-1/2" [64 ]
8" [203 ]
SEE INSTALLNOTE #11
1" [ 25 ]TYPICAL FORALL T-CLIPS
2" [ 51 ]MTG HOLE
SPACING @2
2" [ 51 ]MTG HOLE
SPACING @3
4-1/16" 104[ ]
TOP OF STEEL DIMENSIONS0" 0[ ]
9' 10-1/16" 2998[ ]
18' 1-9/16" 5527[ ]
2' 8-7/8" [835 ]TYP. PER LARGE HOOD
5-1/4" [133 ]DISTANCE BETWEEN
TOP OF HOODAND BTM OF T-CLIP
4" [102 ]DISTANCE BETWEENTOP OF HOODAND BTM OF T-CLIP
9-13/16" 250[ ]0" 0[ ]
2' 11/16" 627[ ]
8' 8-15/16" 2665[ ]
10' 5-1/16" 3176[ ]
11' 7-7/8" 3553[ ]
17' 1-3/4" 5226[ ]
18' 6-3/16" 5643[ ]
10-5/16"
261
[]
0"
0[
]
6" MAX
14' 13/16"
4287
[]
22' 5/16"
6714
[]
6" MAX
24' 6-13/16"
7488
[]
27' 3-1/16"
8308
[]
28' 1-3/8"
8569
[]
1' 7-1/16" 485[ ]
2' 2-3/4" 679[ ]2' 11/16" 627[ ]
11' 7-7/8" 3553[ ]
SEE INSTALLNOTE #11
4" [ 102 ]
6" MAX
3' 6-13/16"
1087
[]
1' 6-11/16" [475 ]TYP. PER SMALL HOOD
# DETAIL DESCRIPTION
1 DISPLAY GP4-AAAxBBB-CC (SEE CHART IN TOP LEFT CORNER)
2 LED COLOR RGB
3 ACTIVE AREA 18' [5486 ] X 27' 7-3/16" [8412 ]
4 OVERALL SIZE 18' 6" [5639 ] X 28' 1-3/16" [8565 ]
5 CABINET ALUMINUM
6 VENTILATION REAR INTAKE & EXHAUST
7 ACCESS SERVICE FROM FRONT OF DISPLAY
8 WEIGHTSECTION 101: 2695 LBS [ 1222 KG] (APPROX)SECTION 201: 3075 LBS [ 1395 KG] (APPROX)TOTAL: 5780 LBS [ 2622 KG] (APPROX)
9 SHIPPINGSHIPPED IN TWO SECTIONS. ASSEMBLY OFSECTIONS IS REQUIRED ON-SITE
10 DIMENSIONS FEET AND INCHES [MILLIMETERS]
STRUCTURAL RATING
1 DESIGN WIND PRESSURE "P" (CASE A) P<= 97 PSF
2 STANDARD/CODE IBC 2009/ASCE7-05
3 MINIMUM STRINGER DIMENSION HSS 4" X 4" X 3/16"
4 MAXIMUM CLIP ANGLE SPACING 10' 6" [3200 ] 1' MAX
POWER RATING PER SINGLE FACE: FOR SIZING ELEC.SERVICE MAX REQ'D SHOWN
MODGRID
SECTIONMAX
WATTS
120/240VAC 1PH 60Hz(3 WIRES + GND)
DOMESTIC
240VAC 1PH 50Hz(2 WIRES + GND)INTERNATIONALSPECIAL ORDER
LINE 1AMPS
LINE 2AMPS
LINE 1(AMPS)
7 X 23 SECTION 101 10408 46.36 40.38 43.37
8 X 23 SECTION 201 11799 46.36 51.97 49.16
15 X 23 TOTAL 22207 92.72 92.35 92.53
VENTILATION REQUIREMENTS
1
DISPLAY RELIES ON VENTILATION TO FUNCTION PROPERLY.VENTILATION HOODS, LOCATED AT THE BACK OF THE DISPLAY,MUST BE ABLE TO DRAW IN AIR AT A TEMPERATURE NOGREATER THAN 120°F
2
AIRFLOW AT AMBIENT TEMPERATURE CAN BE MAINTAINED BY PROVIDINGOPENINGS FOR INTAKE (AT THE BOTTOM) AND EXHAUST (AT THE TOP)BEHIND THE DISPLAY. A MINIMUM OF 16.0 SQFT FOR INTAKE AND16.0 SQFT FOR EXHAUST IS REQUIRED. IF THE OPENINGS CANNOTBE PROVIDED AS STATED, USE WALL MOUNT PROPELLER FANS TOGENERATE A MINIMUM OF 4800 CFM OF AIRFLOW ACROSS THE BACKOF THE DISPLAY.
3
VENTILATION INTAKES ARE FILTERED. FILTERS ARE ACCESSIBLEFROM FRONT AND WILL NEED TO BE PERIODICALLY CLEANED INORDER TO PROVIDE PROPER VENTILATION. REFER TO MAINTENANCESCHEDULE FOR THE RECOMMENDED CLEANING SCHEDULE
INSTALL NOTES
1 WHEN LIFTING USE ALL LIFTLUGS AND MAINTAIN AN ANGLELARGER THAN 55° BETWEEN THE CABINET AND LIFTING DEVICE.
2 1-1/16" LIFTLUG DIAMETER TO ASSIST WITH DISPLAY
INSTALLATION. MAX WIND SPEED DURING INSTALLATIONMUST BE LESS THAN 20 MPH.
3 LIFTLUGS MAY NOT BE USED FOR PERMANENT INSTALLATION.
4DISPLAY WILL BE SHIPPED WITH SOME TOP BORDER COVERSREMOVED. COVERS WILL NEED TO BE ATTACHED WITH INCLUDEDHARDWARE AFTER DISPLAY IS MOUNTED TO STRUCTURE.
5GROUND LUG FOR GROUND CONNECTION. ALL SECTIONS NEED TO BE GROUNDED.
62" MEYERS HUB FOR POWER TERMINATION TO INTERNAL
LOAD CENTER. SEE POWER RATINGS ABOVE.
7SIGNAL INPUT AT QUICK CONNECT. PRIMARY/SINGLE FACEDISPLAY SHOWN. SEE CLEARANCE DIMENSION ON LEFT SIDE VIEW.
8 TWO 1/2" CONDUIT KNOCKOUTS FOR OPTIONAL SIGNAL ENTRANCE.
9DISPLAY WILL BE PAINTED SEMI-GLOSS BLACK ON FRONT AND SIDEPERIMETER WITH MILL FINISH ALUMINUM ON REAR OF DISPLAY.
10 MECHANICAL AND SIGNAL CONNECTIONS OCCUR EXTERNAL TO DISPLAY.
11
T-CLIPS FOR MOUNTING.T-CLIPS CAN BE ADJUSTED VERTICALLY 1/2" AS NEEDED DURING INSTALLATION. T-CLIPS CAN BE
WELDED OR BOLTED TO STRINGER AT A MAX DISTANCE 2-1/2".SEE DETAILS C & D.
12DAKTRONICS IS NOT RESPONSIBLE FOR THE MOUNTING HARDWAREOR THE INTEGRITY OF THE MOUNTING STRUCTURE.
13DAKTRONICS IS NOT RESPONSIBLE FOR THE MAIN ELECTRICALDISCONNECT. SEE POWER RATINGS ABOVE.
14FOR MORE INSTALLATION DETAILS AND GUIDELINESREQUEST DD-1954173 FROM YOUR DAKTRONICS REPRESENTATIVE
PIXELS HIGH (AAA)
PIXELS WIDE (BBB)
PIXEL SPACING (CC)
MAXWATTS
330 506 16MM 22207
270 414 20MM 20201
210 322 26MM 19399
PIXELS HIGH (AAA)
PIXELS WIDE (BBB)
PIXEL SPACING (CC)
176 506 16MM
144 414 20MM
112 322 26MM
PIXELS HIGH (AAA)
PIXELS WIDE (BBB)
PIXEL SPACING (CC)
154 506 16MM
126 414 20MM
98 322 26MM
REV DATE: BY:
DAKTRONICS, INC. THE CONCEPTS EXPRESSED AND DETAILS SHOWN ONTHIS DRAWING ARE CONFIDENTIAL AND PROPRIETARY.DO NOT REPRODUCE BY ANY MEANS WITHOUT THEEXPRESSED WRITTEN CONSENT OF DAKTRONICS, INC. COPYRIGHT 2011 DAKTRONICS, INC.
BROOKINGS, SD 57006
DO NOT SCALE DRAWING
PROJ: GALAXYPRO GP4 SERIESTITLE: SHOP DWG, GP4, 18' 6''x28' 2'' (15x23 MODS)DESIGN: TWHITEH DRAWN: RBASSET DATE: 28-NOV-12SCALE: 1=100
SHEET: REV JOB NO: FUNC-TYPE-SIZE
11203681 OF 1 00 P 1630 E - 10- B
OVERALL DISPLAY SIZEGP4-AAAxBBB-CC
DAKTRONICS
LIGHT SENSOR(DO NOT BLOCK)
SECTION 101GP4-AAAxBBB-CC
SECTION 201GP4-AAAxBBB-CC
FRONT VIEW
SIGNAL INTERCONNECTSEE INSTALL NOTE #10
SIGNAL INTERCONNECTSEE INSTALL NOTE #10
PORTIONS OF TOP BORDER COVERS ARE REMOVED. FOR CLARIFICATIONSEE INSTALL NOTE #4.
SIGNAL INTERCONNECTSEE INSTALL NOTE #10
PRIMARY SIGNAL INPUT QUICKCONNECT. SEE INSTALL NOTE #7
OPTIONAL SIGNAL ENTRANCESEE INSTALL NOTE #8INTAKE HOOD, SEE
VENTILATION NOTES #1, #2, AND #3.
EXHAUST HOODSEE VENTILATIONNOTES #1 AND #2
POWER ENTRANCESEE INSTALL NOTE #6
GROUND LUG. SEEINSTALL NOTE #5.
REAR VIEW
MILL FINISH ALUMINUMREAR OF DISPLAYSEE INSTALL NOTE #9
SEE DETAIL A
SEE DETAIL B
LEFT SIDE
T-CLIPS. SEE DETAILED VIEWS C& D. SEE INSTALL
NOTE #11
USE A GALVANIZED OR WEATHER PROTECTED 5/8" BOLT (MIN ASTM A325), WASHERS (MIN ASTM F436), AND NUT (MIN ASTM A563) OR WELD.
SEE WELD SPECIFICATIONS ON DETAIL D.
DETAIL CTOP AND BOTTOM T-CLIPSSEE INSTALL NOTE #11
(TUBE SHOWN FOR CONCEPT ONLY)SCALE 1/20
SEE HARDWARESPECIFICATIONS ON DETAIL C
DETAIL DSPLICE T-CLIPS
SEE INSTALL NOTE #11(TUBE SHOWN FOR CONCEPT ONLY)
SCALE 1/20
ALL WELDING SHALL BE PERFORMED BY A WELDERCERTIFIED FOR THE SPECIFIED TYPE AND POSITIONOF THE REQUIRED WELD. ALL WELDING SHALL BEIN ACCORDANCE WITH AWS 01.1. SHIELDED METAL
ARC WELDING PROCESSES SHALL BE USED TOPERFORM WELDS WITH A LOW HYDROGEN E70 SERIES
ELECTRODE.
DETAIL ASCALE 1/20
DETAIL BSCALE 1/20
®
3 SIDES1/4"
3 SIDES1/4"
