OSHA’s’focus’ Walking’Working’Surfaces’ Silica YourQuesons Bothast - … ·...
Transcript of OSHA’s’focus’ Walking’Working’Surfaces’ Silica YourQuesons Bothast - … ·...
• OSHA’s focus • Walking Working Surfaces • Silica • Your Ques7ons
OSHA Accident Inves/ga/ons
Walking-‐Working Surfaces
• 1910.21 Scope and defini/ons • 1910.22 General requirements • 1910.23 Ladders • 1910.24 Step bolts and manhole steps. • 1910.25 Stairways • 1910.26 Dockboards • 1910.27 Scaffolds and rope descent systems • 1910.28 Duty to have fall protec/on & falling object protec/on • 1910.29 Fall protec/on systems and falling object protec/on
Criteria and prac/ces • 1910.30 Training requirements. • 1910.66 Powered plaWorms for building maintenance • 1910.67 Vehicle-‐mounted eleva/ng and rota/ng work plaWorms • 1910.140 Personal fall protec/on systems.
Inspec7on, maintenance, and repair • 1910.22(d) -‐ The employer must ensure:
• (1) Walking-‐working surfaces are inspected, regularly and as necessary, and maintained in a safe condi7on;
• (2) Hazardous condi7ons corrected or repaired before an employee uses the walking-‐working surface again. If the correc7on or repair cannot be made immediately, the hazard must be guarded to prevent employees from using the walking-‐working surface un7l the hazard is corrected or repaired; and
Ladders 1910.23 • (b)(8) Ladders are used only for the purposes for which they were designed;
• (b)(9) Ladders are inspected before ini7al use in each work shiR, and more frequently as necessary, to iden7fy any visible defects;
• (b)(10) Any ladder with defects is tagged “Dangerous: Do Not Use” and removed from service un7l repaired
Fixed ladders 1910.29(b)(9)
• For fixed ladders that extend more than 24 feet (7.3 m) above a lower level, the employer must ensure:
• (A) Exis7ng fixed ladders. Each fixed ladder installed before November 19, 2018 is equipped with a personal fall arrest system, ladder safety system, cage, or well;
• (B) New fixed ladders. Each fixed ladder installed on and aRer November 19, 2018, is equipped with a personal fall arrest system or a ladder safety system;
Fixed ladders • (C) Replacement. When a fixed ladder, cage, or well, or any por7on of a sec7on thereof, is replaced, a personal fall arrest system or ladder safety system is installed in at least that sec7on of the fixed ladder, cage, or well where the replacement is located; and
• (D) Final deadline. On and aRer November 18, 2036, all fixed ladders are equipped with a personal fall arrest system or a ladder safety system.
Dockboards 1910.26 • Dockboard means a portable or fixed device that spans a gap
or compensates for a difference in eleva7on between a loading pladorm and a transport vehicle. Dockboards include, but are not limited to, bridge plates, dock plates, and dock levelers.
• (b)(1) Dockboards put into ini/al service on or a\er January 17, 2017 are designed, constructed, and maintained to prevent transfer vehicles from running off the dockboard edge;
• (d) The employer must ensure measures, such as wheel chocks or sand shoes, are used to prevent the transport vehicle (truck, semi-‐trailer, trailer, or rail car) on which a dockboard is placed, from moving while employees are on the dockboard;
Scaffolds 1910.27 • (a) Scaffolds used in general industry must meet the requirements in 29 CFR part 1926, subpart L
Scaffold Requirements
• Daily Inspection
• Fall protection at 10 feet
• Safe access provided to scaffold platform
• Footing capable of preventing displacement
• All work platform levels fully planked
• Ensure that scaffolding is kept at least 10 feet from power lines.
Fall hazards within 6 feet of edge • (b)(1) employer must ensure that each employee on an unprotected side or edge that is 4 feet (1.2 m) or more above a lower level is protected by one of the following: – (A) Guardrail systems; – (B) Safety net systems; or – (C) Personal fall protec7on systems, such as personal fall arrest, travel restraint, or posi7oning systems.
Work on low-‐slope roofs 1910.29(b)(13)
• (ii) When work is performed at least 6 feet (1.6 m) but less than 15 feet (4.6 m) from the roof edge, the employer may use a designated area when performing work that is both infrequent and temporary.
– Employees remain within the designated area
– The perimeter is delineated with a warning line consis7ng of a rope, wire, tape, or chain
Designated areas • (2) The employer must ensure each warning line:
– (i) Has a minimum breaking strength of 200 pounds; – (ii) Is installed so its lowest point, including sag, is not less than 34 inches and not more than 39 inches;
– (iii) Is supported in a manner that pulling on the line will not result in slack being taken up in adjacent sec7ons causing the line to fall below the limits
– (iv) Is clearly visible from a distance of 25 feet – (v) Is erected as close to the work area as the task permits; and
– (vi) Is erected not less than 6 feet (1.8 m) from the roof edge
If the work is more than 15 feet away and both infrequent and temporary
– The employer must implement and enforce a work rule prohibi7ng employees from going within 15 feet (4.6 m) of the roof edge
personal fall protec/on systems 1910.140
• This sec7on establishes performance, care, and use criteria for all personal fall protec7on systems.
Vehicle-‐mounted eleva/ng and rota/ng work plaWorms 1910.67
• (v) A personal fall arrest or travel restraint system that meets the requirements in subpart I of this part shall be worn and aiached to the boom or basket when working from an aerial liR.
Training requirements 1910.30 • Each employee is trained by a qualified person on or before May 17, 2017 on… – (i) Nature of the fall hazards and how to recognize them; – (ii) Procedures to be followed to minimize the hazards; – (iii) The correct procedures for installing, inspec7ng, opera7ng, maintaining, and disassembling the personal fall protec7on systems that the employee uses;
– (iv) The correct use of personal fall protec7on systems and equipment including, but not limited to, proper hook-‐up, anchoring, and 7e-‐off techniques, and methods of equipment inspec7on and storage, as specified by the manufacturer.
– the proper care, inspec7on, storage, and use of equipment before an employee uses it
Retraining requirements 1910.30 • The employer must retrain an employee when the employer has reason to believe the employee does not have the understanding and skill required including:
– (1) When changes in the workplace render previous training obsolete or inadequate;
– (2) When changes in the types of fall protec7on systems or equipment to be used render previous training obsolete or inadequate; or
– (3) When inadequacies in an affected employee's knowledge or use of fall protec7on systems or equipment indicate that the employee no longer has the requisite understanding or skill necessary to use equipment or perform the job safely.
Effec7ve January 17, 2017 • Inspec7on and cer7fica7on of permanent building anchorages -‐ 1 year;
• Installa7on of fall protec7on (personal fall arrest systems, ladder safety systems, cages, wells) on exis7ng fixed ladders (over 24 feet) that do not have fall protec7on -‐ 2 years;
• Installa7on of ladder safety systems or personal fall arrest systems on all fixed ladders (over 24 feet) – 20 years.
OSHA’s Respirable Crystalline Silica Rule Exposures from chipping, cuong, sawing, drilling, grinding, sanding, and crushing concrete, brick, block, rock and stone
22
Final Rule Published on March 25, 2016
Construc7on employers must comply by June 23, 2017 General Industry employers must comply by June 23, 2018, except :
Employers must comply with the ac7on level trigger for medical surveillance by June 23, 2020. (The PEL is the trigger from June 23, 2018 through June 23, 2020.)
23
Scope of Coverage • Three forms of silica:
– quartz, – cristobalite – tridymite
• All occupa7onal exposures to respirable crystalline silica are covered
Permissible Exposure Limit (PEL)
• PEL = 50 µg/m3 as an 8-‐Hour TWA
• Ac7on Level = 25 µg/m3 as an 8-‐Hour TWA
24
Scheduled Monitoring Op7on • Prescribed schedule for ini7al and periodic personal monitoring
• If monitoring indicates: • Ini7al below the AL: no addi7onal monitoring • Above the AL: repeat within 6 months • Above the PEL: repeat within 3 months • When two consecu7ve non-‐ini7al results, taken 7 or more days apart, are below the AL, monitoring can be discon7nued
• Reassess if circumstances change
25
List of Table 1 Entries § Sta7onary masonry saws § Handheld power saws § Handheld power saws for fiber
cement board § Walk-‐behind saws § Drivable saws § Rig-‐mounted core saws or drills § Handheld and stand-‐mounted drills § Dowel drilling rigs for concrete § Vehicle-‐mounted drilling rigs for
rock and concrete § Jackhammers and handheld
powered chipping tools
§ Handheld grinders for mortar removal (tuckpoin7ng)
§ Handheld grinders for other than mortar removal
§ Walk-‐behind milling machines and floor grinders
§ Small drivable milling machines § Large drivable milling machines § Crushing machines § Heavy equipment and u7lity vehicles
to abrade or fracture silica materials § Heavy equipment and u7lity vehicles
for grading and excava7ng
26
Example of Table 1 Entry
Equipment / Task
Engineering and Work Prac/ce Control Methods
Required Respiratory Protec/on and Minimum APF
≤ 4 hr/shiR > 4 hr/shiR
Handheld power saws (any blade diameter)
Use saw equipped with integrated water delivery system that con7nuously feeds water to the blade. Operate and maintain tool in accordance with manufacturers’ instruc7on to minimize dust -‐ When used outdoors -‐ When used indoors or in an
enclosed area
None APF 10
APF 10 APF 10
27
Example of Table 1 Entry
Equipment / Task
Engineering and Work Prac/ce Control Methods
Required Respiratory Protec/on and Minimum APF
≤ 4 hr/shiR > 4 hr/shiR
Sta/onary masonry saws
Use saw equipped with integrated water delivery system that con7nuously feeds water to the blade. Operate and maintain tool in accordance with manufacturer’s instruc7ons to minimize dust emissions.
None None
28
Construc/on – Competent Person
• Competent person is an individual capable of iden7fying exis7ng and foreseeable respirable crystalline silica hazards, who has authoriza7on to take prompt correc7ve measures
• Makes frequent and regular inspec7on of job sites, materials, and equipment
• Construc/on employers must designate a competent person to implement the wrifen exposure control plan
29
30
Construc7on – Wriien Exposure Control Plan
• The plan must describe: • Tasks involving exposure to respirable crystalline silica
• Engineering controls, work prac7ces, and respiratory protec7on for each task
• Housekeeping measures used to limit exposure • Procedures used to restrict access, when necessary to limit exposures
Housekeeping • When it contributes to exposure, employers must prohibit: • Dry sweeping or brushing • Use of compressed air for cleaning surfaces or clothing
Employer should use ven/la/on, HEPA vacuums, and wet sweeping.
31
GI Medical Surveillance • The employer shall make medical surveillance available at no cost to the employee, and at a reasonable 7me and place, for each employee who will be occupa7onally exposed to respirable crystalline silica at or above the ac7on level for 30 or more days per year
• within 30 days of ini7al assignment
• Employers must offer examina7ons every three years to workers who con7nue to be exposed above the trigger
32
Medical Exam
• Medical and work history, • Physical exam, • Chest X-‐ray, • Pulmonary func7on test
• (TB test on ini7al exam only)
33
Training • Employers required to comply with hazard communica7on standard (1910.1200)
• Address at least the following hazards: Cancer, lung effects, immune system effects, and kidney effects as part of HCS
• Train workers on health hazards, tasks resul7ng in exposure, workplace protec7ons, medical surveillance, and elements of the standard.
34
Ques7ons?
35
Brian Bothast Lead Safety and Occupa7onal Health Specialist
Peoria Area OSHA Office T 309.589.7033