ORING hand book handbook.pdf
-
Upload
bandarswcc -
Category
Documents
-
view
54 -
download
10
Transcript of ORING hand book handbook.pdf
-
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com
The Seal Mans O-Ring Handbook
Published by: EPM, Inc. - The Seal Man112-G West Burke StreetStockbridge, GA 30281www.epm.com
Phone: (800) 659-5050 or (770) 389-0501 Fax: (888) 353-7325 or (770) 389-0652
Copyright 2004 EPM, Inc. - The Seal Man. All rights reserved. This manual is copyrighted. No parts ofthis publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any meanselectronic, mechanical, photocopy, recording, or any otherexcept for brief quotations in printed reviews, with-out prior written approval of the publisher. Printed copies may be made for personal reference and use only.
Content by Jerry Whitlock and EPM, Inc.Edited by Eric JacksonCover design by Eric JacksonCover photo by Millie Batson and Jerry Whitlock
Distributed in the United States by EPM, Inc. - The Seal Man.
First Edition
For information on EPM, Inc. or to place an order, please contact our Sales department by phone at (800) 659-5050 or (770) 389-0501, fax at (888) 353-7325 or (770) 389-0652, or visit our web site at www.epm.com.
Trademarks: All brand names and product names used in this book are trade names, service marks, trademarks,or registered trademarks of their respective owners. EPM, Inc. is not associated with any product or vendor men-tioned in this book.
LIMIT OF LIABILITY/DISCLAIMER OFWARRANTY: PUBLISHER AND EDITORS HAVE USEDTHEIR BEST EFFORTS IN PREPARING THIS MANUAL. EPM, INC. AND EDITORS MAKE NOREPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY ORCOMPLETENESS OF THE CONTENTS OF THIS MANUALAND SPECIFICALLY DISCLAIMANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULARPURPOSE. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTIONSCONTAINED IN THIS PARAGRAPH. NO WARRANTYMAY BE CREATED OR EXTENDED BYSALES REPRESENTATIVES OR WRITTEN SALES MATERIALS. THE ACCURACYANDCOMPLETENESS OF THE INFORMATION PROVIDED HEREIN AND THE OPINIONS STATEDHEREIN ARE NOT GUARANTEED OR WARRANTED TO PRODUCE ANY PARTICULARRESULTS, AND THE ADVICE AND STRATEGIES CONTAINED HEREIN MAY NOT BESUITABLE FOR EVERY INDIVIDUAL. NEITHER EPM, INC., NOR THE EDITORS SHALL BELIABLE FOR ANY LOSS OF PROFIT OR ANY OTHER COMMERCIAL DAMAGES, INCLUDINGBUT NOT LIMITED TO SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR OTHER DAMAGES.
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com
47 Billion Seals In Stock.........................................................................................4Who Is The Seal Man..............................................................................................5What Is An O-Ring..................................................................................................6How To Achieve Optimum O-Ring Performance...................................................... 7O-Ring Characteristics............................................................................................8O-Ring Limitations..................................................................................................9Major Dynamic Sealing Problems.................................................................... 10-14Conformability...................................................................................................... 15Why O-Rings Fail.................................................................................................. 16O-Ring Failure Analysis................................................................................... 17-26The Top Four Causes of Hydraulic Cylinder Seal Failure.................................. 27-28Other Seal Types That Will Replace O-Rings.........................................................29O-Ring Materials
Material Selection Guide..........................................................................30-36Material Hardness Scale...............................................................................37Material Rankings by:
Temperature Range.............................................................................38Surface Speed Limitations...................................................................39Oil Resistance.....................................................................................40Abrasion Resistance............................................................................ 41Tear Resistance................................................................................... 42Relative Price...................................................................................... 43
Fluid Compatability Guide..............................................................................44-103Armor-O-Rings / PTFE Encapsulated O-Rings...........................................104-108Groove Dimensions......................................................................................109-111Maximum Recommended Gap Clearance..................................................... 112-113O-Ring Sizes
Inch Sizes...........................................................................................114-124Metric Sizes.........................................................................................125-158Shadow Graphs...................................................................................159-194
SUPERSmall O-Rings........................................................................................195Back-up Rings............................................................................................. 196-199Spliced, Endless Cord
O-Ring Cord........................................................................................ 200-201Square Cord............................................................................................... 202Q-Lobe Cord...............................................................................................203Rectangular Cord........................................................................................204How To Make Spliced, Endless O-Rings Using O-Ring Cord.........................205
Square-Cut Rings.........................................................................................206-208Q-Lobe Rings...............................................................................................209-211O-Ring Kits & Assortments..........................................................................212-225O-Ring Tools.......................................................................................................226How To Order The O-Ring You Need...................................................................227How To Select The Material You Need................................................................ 228O-Ring Storage, Handling, and Installation........................................................ 229
Table of Contents
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 4
-
Who is The Seal Man?
Introducing, Mr. Jerry Whitlock, The Seal ManThere is an old marketing strategy whichsays, become known by that which yourcustomers call you. Over 30 years ago, thecustomers of Jerry Whitlock began to callhim The Seal Man because they realizedthat he was one of the most knowledgeableseal and gasket specialists in the entireworld. Jerrys experience has carried himaround the world as a sought after businessman, consultant, advisor, lecturer, traininginstructor and on-sight trouble shooter. TheSeal Mans specialties include solutions forhigh pressure and high temperature sealingapplications; large diameter seals and pack-ings; rotating and reciprocating equipmentsealing applications specialist; oil seals and any joint gasketing problem solving. Toquote Jerry Whitlock - There is NO international standard or special seal that we can-not provide - NONE. I can guarantee you, if I cannot supply you the seal or gasket youneed, it probably does not exist.
Jerry Whitlock: acts as a consultant to international seal and gasket firms. is available to companies outside the U.S. who need assistance establishing seal and
gasket or industrial business in the U.S. has market studies available for the U.S. seal and gasket market. is a specialist in Internet marketing. has traveled extensively.
Mr. Whitlock is available for interviews for TV, radio, newspaper, andmagazine.
Subjects of specialty:
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 5
Cyber Executive Internet Marketing E-Commerce / Electronic Commerce Industrial Marketing Marketing Business Management Import / Export
Seals & Gasket Marketing International Business Industrial Distribution in the U.S. Largemouth Bass Fishing Lake Oconee, GA Hybrid Bass Fishing
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 6
What Is An O-Ring?
O-Ring DescriptionAn O-Ring is a torus, or doughnut-shaped object, generally made from an elastomer.O-Rings can also be made in PTFE and other plastic materials, and in metals, both hol-low and solid. They are used primarily for sealing. Another use is for light duty drivebelts.
Basic PrinciplesAn O-Ring seal is a means for closing off a passageway preventing an unwanted escapeor loss of fluid. The seal consists of an O-Ring installed in a gland and is exactly that -a circular run in which the elastomeric material has a section that is virtually circle.The gland is the cavity (usually within metal) into which the O-Ring is placed. Thecombination of these two elements comprises an O-Ring seal.
UseO-Rings are used in two general design applications: static (non-mov-ing) and dynamic (moving). Static applications may range from vacu-um to over 60,000 psi for sealing flanges and O-Ring grooves. O-Ringseals with lobed cross sections were designed for both static anddynamic applications. The four and six lobed configurations resist spiralfailure and also extrusion failure in applications with large clearancebetween parts. Of the some 20 different types of O-Ring seals available, the commonround cross section O-Ring type is the most versatile. The conventional type of O-Ringmay be used in almost any application if the gland to contain the seal is deisgned cor-rectly and the right size and material is chosen.
OperationAll fluid-tight seals are characterized by the absence of any passage by which fluidmight escape. Detail differences exist in the manner by which zero clearance isobtained - welding, brazing, soldering, ground or lapped fits or the yielding of a softermaterial wholly or partially confined between two harder and stiffer members of thestructure. The O-Ring seal falls in the latter class. The rubber seal should be consid-ered as an incompressible, viscous fluid having a very high surface tension. Now,whether by mechanical perssure from the surrounding structure or whether by pressuretransmitted through hydraulic fluid, this extremely viscous fluid (the elastomeric O-Ring) is forced to flow in the gland to produce zero clearance or a positive block to theflow of the less viscous fluid being sealed. The rubber absorbs the stack-up of toler-ances of the unit and its memory maintains a sealed condition.
Before Installation After Installation With System Pressure
-
How To Achieve Optimum Performance of An O-Ring
The successful use of O-Rings depends upon many factors:
A. Surface Finish - All metal surfaces over which the O-Ring moves shouldbe held to a maximum finish of 16 RMS, although the groove finish canhave a maximum of 32 RMS. There should be no nicks, burrs, orscratches.
B. Metals - All metals over which anO-Ring moves should have a hardsurface such as steel, nickel-plated,or chrome-plated. Special attentionshould be given if you select softmetals such as aluminum, brass, orbronze.
C. Excessive Metal Clearance -Clearances should be held to therecommended maximum diametricaltolerance. Consideration must be given to the breathing of cylinder in yourcalculations - which is the possibility of the cylinder bore to expand orballoon out at its center.
D. Concentricity - It is important to hold eccentricity within therecommened practice and to design for sufficient bearing area to takecare of side loads or off center loading.
E. Cleanliness - All systems should be kept clean and free from dirt, grit,chips, and any foreign materials. Any type of abrasive material will cut theO-Ring. When replacing a failed O-Ring, look for tiny metal chipsembedded into the O-Ring, which could mean a pump problem.
F. Squeeze (preload) - For good sealing, the minimum diametrical squeezeshould be observed. Where pressures are low and friction is critical, theamount of squeeze can be decreased but caution should be excercized.
G. Lubrication - When used in pneumatic systems, O-Rings should be lubri-cated. If permitted to run dry, then they will face abrasion and twisting.
H. Groove Design - Proper design is a most essential factor in the successfuloperation of O-Rings. The rectangular shaped groove is recommendedexcept for special applications.
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 7
-
O-Ring Characteristics
An early and prominent user of O-Rings cites characteristics of O-Ring seals of interestto designers. 1The more general characteristics are:
A. The seals can be made perfectly leak-proof for cases of static pistons andcylinders for fluid pressures up to 5,000 psi (limit of test pressure). Thepressure may be constant or variable.
B. The seals can be made to seal satisfactorily between reciprocating pistonsand cylinders at any fluid pressure up to 5,000 psi. There may be slightrunning leakage (a few drops per hundred strokes) depending on the filmforming ability of the hydraulic medium. O-Rings can be used betweenrotating members with similar results but in all cases the surface rubbingspeed must be kept low.
C. A single O-Ring will seal with pressureapplied alternately on one side and then onthe other side. However, in cases of severeloading or usage under necessarilyunfavorable conditions, seal life can beextended by designing the mechanismso that each seal is subjected to pressurein one direction only. Seals may be arrangedin series as a safety measure, but the firstseal exposed to pressure will take full load.
D. O-Ring seals must be radially compressed between the bottom of the sealgroove and the cylinder wall for proper sealing action. This compressionmay cause the seal to roll slightly in its groove under certain conditions ofpiston motion, but the rolling action is not necessary for normal operationof the seals.
E. In either static or moving applications, when the O-Ring seal is under highpressure the primary cause of seal failure is extrusion of the seal materialinto the piston-cylinder clearance. The major factors affecting extrusion arefluid pressure, seal hardness and strength, and piston-cylinder clearance.
F. Moving seals may fail by abrasion against the cylinder or piston walls. Therefore, the contacting surfaces should be suitably finished for long seallife. Moving seals that pass over ports or surface irregularities, while underhydraulic pressure, are very quickly cut or worn to failure.
1 Excerpt taken from: O-Ring Seals in the Design of Hydraulic Mechanisms A paper presented at the S.A.A. AnnualMeeting, January 1947 by Mr. D.R. Pearl of Ha,. Std. Prop. Div. of United Aircraft Corp.
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 8
-
O-Ring Limitations
Although it has been stated that O-Rings offer a reasonable approach to the idealhydraulic seal, they should not be considered the immediate solution to all sealingproblems. It has been brought out in the forgoing discussion that there are cetain defi-nite limitations on their use, for example, high temperature, high rubbing speeds, cylin-der ports over which seals must pass, and large clearances. Disregard for these limita-tions will result in poor seal performance. Piston rings, lip type seals, lapped fits, flatgaskets and pipe fitting all have their special places in hydraulic design, but where thedesign specifications permit the proper use of O-Rings, they will be found to give longand dependable service.2
While no claim is made that an O-Ring will serve best in all conditions, it merits consid-eration for most seal applications except:
A. Rotary speeds exceeding 1,500 feet per minuteB. An environment completely incompatible with any elastomeric material.C. Just plain insufficient structure (for anything but a flat gasket).
O-Ring Life Cycle
2O-Ring Seals in the Design of Hydraulic Mechanisms A paper presented at the S.A.A. Annual Meeting, January,1947 by Mr. D.R. Pearl of Ha,. Std. Prop, Div. of United Aricraft Corp.
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 9
1. Installation of O-Ring 2. Pressure Applied to O-Ring (Ideal)
3. Extrusion of O-Ring 4. Failure of O-Ring
-
Major Dynamic Sealing Problems
FRICTIONFriction is the rubbing force or resistance to motion between two surfaces that aretouching each other.
Example: Seal material touching metal.
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 10
Variable
A. Fluid pressure on seal
B. Surface Finish
C. Seal materialhardness
D. Seal materialtemperature
E. Contact area betweenmetal and seal
F. Lubricity of fluid
G. Coefficient of frictionof seal material
Reduce pressure(seldom practical).
Smooth to 2 - 4 (10microinches) RMSmaximum.
Select softer material forsqueeze seals; usuallyselect a harder materialfor lip seals.
Cool the fluid and seal;if this is not possible,use smaller seal cross-section or larger grooveto reduce hot squeeze.
Reduce width of contactline of lip-type seal;increase width of line ofsqueeze-type seals (lowpressure applications).
Select higher-lubricityfluid.
Use low-coefficientcompound if systemmust run dry; check drylubricant additivesand/or fiber reinforce-ment for retention oflimited lubricant (if welllubricated, coefficient ofdry seal compound haslittle relevance).
To Reduce Friction Variable
H. Shape of surfaceirregularities
I. Fluid entrapmentbetween seal andmetal
J. Orientation of surfaceirregularities
K. Time-at-rest betweenseal and metal
L. Speed of surfacemotion
M. Compression forceson seal
N. Direction of motion
O. Extrusion of seal intoclearance gap(jamming)
No sharp angles; shal-lower angle to surface(seldom practical).
Experiment with higher-viscosity fluid, lowercontact force, lip shape,fiber reinforcement forlube wicking.
Hone linearly for axialorientation of tool marks(seldom practical due toincreased leakage).
Reduce time betweenmovements.
Increase speed; this willincrease hydroplaningand related leakage.
Reduce squeeze on seal;avoid putting squeeze onheel of seals.
Select seal shape lessprone to wedging incritical direction.
Reduce clearance gap;use anti-extrusion deviceand/or extrusionresistant seal.
To Reduce Friction
-
Major Dynamic Sealing Problems
WEAR
Wear - to diminish gradually by friction and rubbing motion.
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 11
Like a pencil eraser, an O-Ring is being worn awayeven though you may not see it until failure.
-
Major Dynamic Sealing Problems
SEALABILITY
Sealability is the ability of a material to conform to a surface to block the flow ofa liquid.
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 12
-
Major Dynamic Sealing Problems
STABILITYStability is the ability of a seal to resist rolling, twisting and shifting in a groove.
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 13
-
Major Dynamic Sealing Problems
EXTRUSIONExtrusion is the flowing of the seals body into the clearance gap under pressure.
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 14
-
Conformability
Conformability is the ability of a seal compound to fill or dam the minute irregularitiesthat are in the metal surface.
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 15
O-Ring Without Pressure
O-Ring With Pressure
-
Why Do O-Rings Fail?
O-Rings, made of an elastomeric material, are unlike other materials. The reason forthis is because in order for an O-Ring to function properly it is has to deform. Once anO-Ring is installed into a gland it is then compressed resulting in zero clearance. Itsthat zero clearance that seals the flow of fluids and gases. As the actuating pressureincreases, so does the force acting on the surfaces, making a tighter seal and deform-ing the O-Ring. This sealing procedure works well for a lot of fluid-power systems.However, in order for it to work well it requires careful design, selection, and installa-tion procedures.
The combined effects of different environmental factors usually result in a typicalO-Ring failure. Some of the most common causes of an O-Ring failure are:
A. Incompatibility between the O-Ring material and the fluid it is to seal.(See our Fluid Compatibilty Guide on pages 44-103)
B. The wrong O-Ring size.C. O-Ring not installed correctly.D. Improper gland design. This allows for too much compression and too little
compression, not enough room for displacement under compression, ortolerance stack-up.
E. Not enough O-Ring lubrication.
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 16
-
O-Ring Failure Analysis
COMPRESSION SET
Description of failure appearance:This failure is common to both static and dynamic sealing applications. This type offailure produces flat surfaces on the sides of the O-Ring that were compressed, usuallythe top and bottom if sitting flat on a desk.
The sources of COMPRESSION SET failure: The O-Ring material used has poor compression set resistance The O-Ring material used has limited resistance to heat The O-Ring is swelling in the groove due to fluid incompatability The O-Ring has too much squeeze in the groove
How to eliminate COMPRESSION SET failure: Use a higher quality, low compression set material Check the compatability of the O-Ring material to the fluid Select a material good for heat produced in operation Double check the groove dimensions for proper squeeze Check existing O-Ring stock for physical properties
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 17
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 18
O-Ring Failure Analysis
ABRASION
Description of failure appearance:This failure is most common in dynamic sealing applications - like reciprocating androtating shafts. This type of failure produces a flattened surface on the side of theO-Ring body subjected to the movement.
The sources of ABRASION failure: The metal surfaces are too rough and are abrasive to the O-Ring The metal surfaces are too smooth, not allowing proper lubrication No lubrication in the design Operating temperatures are too high for the material The system fluid is contaminated with abrasive particles
How to eliminate ABRASION failure: Change surface finishes to recommended Arrange for better lubrication Use a material suitable for higher temperatures Eliminate any source of contamination Change to a more abrasion resistant O-Ring material
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 19
O-Ring Failure Analysis
INSTALLATION
Description of failure appearance:This failure can occur in both static and dynamic O-Rings. Short nicks or scratches orpeeling on the surface of the O-Ring can be noticed.
The sources of INSTALLATION failure: The use of sharp edged tools Sharp corners on the O-Ring groove Sharp threads that the O-Ring passes over No lead-in chamfer O-Ring was not lubricated O-Ring was twisted or trapped between metal surfaces Poor quality of the material
How to eliminate INSTALLATION failure: Cover all threads with masking tape Break all sharp edges Create a 15 to 20 degree lead-in chamfer Lubricate O-Ring during installation Use correct sized O-Ring
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 20
O-Ring Failure Analysis
EXPLOSIVE DECOMPRESSION
Description of failure appearance:You will find random ruptures, crater-like pores and small slits, which have originatedwithin the body of the O-Ring.
The sources of EXPLOSIVE DECOMPRESSION failure: Gases permeating the O-Ring material Rapid decompression of those gases Micro-explosions occuring as decompression takes place
How to eliminate EXPLOSIVE DECOMPRESSION failure: Slow system cycles down Increase time for decompression Replace with a harder material Select a smaller O-Ring cross section
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 21
O-Ring Failure Analysis
HEAT HARDENING AND OXIDATION
Description of failure appearance:You will see this failure in both static and dynamic O-Rings. A flattened area willappear on the dynamic surface. Sometimes cracked, hardened and pitted areas can beseen throughout the entire body of the O-Ring.
The sources of HEAT HARDENING AND OXIDATION: Temperatures higher than recommended for the material Elastomers becoming dry and portions of the material evaporating Oxidation
How to eliminate HEAT HARDENING AND OXIDATION: Lower the operating temperatures of the system Use O-Rings rated for higher temperatures
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 22
O-Ring Failure Analysis
SPIRAL DAMAGE
Description of failure appearance:The surface of the O-Ring appears to have been twisted, or to have rolled in its grooveor against a reciprocating rod. It stays in this position when freed.
The sources of SPIRAL DAMAGE: Side loads causing excessive clearance Mis-fit components No suitable lubrication Material too soft Moving speed too slow Surfaces are uneven
How to eliminate SPIRAL DAMAGE: Decrease the clearances between components Check for roundness of fitting parts Machine surfaces to suitable finishes Provide lubrication Select a harder material Add a back-up ring
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 23
O-Ring Failure Analysis
EXTRUSION
Description of failure appearance:You will see a ridge, nibbles and small missing pieces of the material along either theinner diameter or outer diameter due from the down-stream side of the O-Ring.
The sources of EXTRUSION: Excessive system pressures Too much clearance between mating parts Material too soft O-Ring body too large for the groove Improperly machined groove Attack by system fluid
How to eliminate EXTRUSION: Decrease or regulate system pressure Refit mating parts, machining back to proper, concentric fit Select a harder material Determine correct O-Ring cross section size Add back-up rings Re-machine groove to include clean, smooth groove edges Replace O-Ring with different type of seal
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 24
O-Ring Failure Analysis
EXCESSIVE SWELL
Description of failure appearance:Identified by obvious dimension of the body of the O-Ring. Reduced physical proper-ties, which causes improper fit. Heat and friction excelerates seal failure.
The source of EXCESSIVE SWELL: The material absorbs system fluids causing swelling An obvious chemical incompatability
How to eliminate EXCESSIVE SWELL: Test material for fluid compatability Consult a chemical compatability chart to determine suitable material
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 25
O-Ring Failure Analysis
WEATHERING OR OZONE CRACKING
Description of failure appearance:Exposure of either static or dynamic sealing O-Ring to weather, atmosphere, polutionsand ultra-violet light.
The source of WEATHERING OR OZONE CRACKING: Attack of the polymer chains, destruction of the material causing cracking
How to eliminate WEATHERING OR OZONE CRACKING: Select a material that resists ozone exposure
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 26
O-Ring Failure Analysis
NO APPARENT REASON FOR FAILURE
Description of failure appearance:Difficult to pin-point due to non-obvious, unseen reasons
The source of NO APPARENT REASON FOR FAILURE: Combined tolerances of all components not correct Not enough squeeze Parts not fitting properly Components not round Too much flash, remaining rubber on O-Ring Improper groove shape
How to eliminate NO APPARENT REASON FOR FAILURE: Re-machine all parts for proper sizing tolerances Make sure the amount of squeeze is correct Double check the design Replace components not fitted correctly Select a different material or O-Ring source for clean ground outer diameters Check published data for groove shapes and sizing
-
The Top Four Causes of Hydraulic Cylinder Seal Failureby Jerry Whitlock - The Seal Man
Hydraulic cylinder seals cost the manufacturer pennies. They are usually purchased ona low bid basis. But, that simple, inexpensive seal can cost you thousands in downtimeand loss of production if it fails. If you have a problem seal, focus on these four pointsto help determine the cause of failure.
1. Improper installation is a major cause of sealfailure. The important things to be watched duringseal installation are: (a) cleanliness, (b) protectingthe seal from nicks and cuts, and (c) proper lubri-cation. Other problem areas are over tightening ofthe seal gland where there is an adjustable glandfollower or folding over a seal lip during installa-tion. Installing the seal upside down is a commonoccurrence, too. The solution to these problems iscommon sense and taking reasonable care during assembly.
2. System contamination is another major fac-tor in hydraulic seal failure. It is usually caused byexternal elements such as dirt, grit, mud, dusteven ice and internal contamination from circulat-ing metal chips, break-down products of fluid,hoses or other degradable system components. Ascontamination can be prevented by a proper filter-ing of system fluid. Contamination is indicated byscored road and cylinder bore surfaces, excessiveseal wear and leakage - and sometimes tiny pieces of metal imbedded in the seal.
3. Chemical breakdown of the seal material is most often the result of incorrectmaterial selection in the first place or a change ofhydraulic system fluid. Misapplication or use ofnon-compatible materials can lead to chemicalattack on the seal by fluid additives, hydrolysisanoxidation reduction of seal elements. Chemicalbreakdown can result in loss of seal lip interface,softening of seal durometer, excessive swelling orshrinkage. Discoloration of the seal can also be anindicator of chemical attack.
continued on next page...
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 27
-
The Top Four Causes of Hydraulic Cylinder Seal Failureby Jerry Whitlock - The Seal Man
(continued)
4. Heat degradation is to be suspected when thefailed seal exhibits a hard, brittle appearanceand/or shows a breaking away of parts of the seallip or body. Heat degradation results in loss ofsealing lip effectiveness through, excessive com-pression set and/or loss of seal material. Causesof their condition may be use of incorrect sealmaterial, high dynamic friction, excessive lip load-ing, no heel clearance and proximity to outsideheat source. Correction of heat degradation problems may involve reducing seal lipinterference, increasing lubrication, or a change of the seal material. In borderline sit-uations consider all upper temperature limits to be increased by 50 degrees Fahrenheitin hydraulic cylinder seals at the seal interface due to running friction caused by thesliding action of the lips.
Heres a secret - it is not necessary tobuy replacement seals from the originalhydraulic cylinder manufacturer. Manyseal suppliers have the same exactseals that are used in most hydrauliccylinders and can easily cross referenceor match up a replacement. In manycases, if there is a recurring problemwith a seal, our seal specialist can rec-ommend a solution and increase the lifeof the seal.
Jerry Whitlock in known as The Seal Man. He has over 30 years experience in theseal industry. Jerry owns and operates EPM, Inc. located in Atlanta, GA. His web site -www.epm.com - is the largest and most visited web site for seals on the internet.
More O-Ring Failure InformationSee our complete O-Ring Failure Analysis section beginning on page 17 for moredetailed information about O-Ring failures. Also, you can contact your EPM CustomerHelper and ask about our Free Seal Failure Analysis.
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 28
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 29
Other Seal Types That Will Replace O-RingsAny of the seal types below can be used in the place of an O-Ring.
EPM can supply any of these seals.
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 30
Material Selection Guide
Here is a list of available O-Ring materials. Material usage will depend upon theenvironment the O-Ring is to be used in. Various fluids, gases, temperatures, andother environmental properties will affect the material. Please review this guide andour Fluid Compatibility Guide on pages 44-103 to help you in your material selection.
*Note: This is to serve as a reference guide only. Please contact your EPM CustomerHelper regarding any questions or for more information on any material.
SealMaterial
HPUPolyurethane
Also referred to as:Urethane, HPU, PUR
Red
(could alsobe NaturalMilky Whiteor honeyColored)
-22 to 230F
-30 to 110C
Color TemperatureLimits
95 N/A
Use in: Hydraulic cylinders asrod seals and piston seals. Thismaterial is most commonlyused as hydraulic u-cups, rodwipers and packings.
Description: This is a highperformance material withimproved resistance to hotwater (up to 200F) makes itideally suited for mining appli-cations where water basedhydraulic fluids are used. Canbe used for pressures to 6000psi. It is excellent in oil basedhydraulic fluids. Great abrasionresistance. Resistant to mostoils, fuels, and gases. Can beused successfully as a drivebelt of various shapes.
Characteristics: Plastic-like.Shiny surface finish. Difficult tostretch.
HardnessMachined
O-RingMoldedO-Ring
Information
See page 37 for ahardness scale.
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 31
SealMaterial
NBRNitrile Rubber
Also referred to as:NBR, Buna-N, Buna
Black
-22 to 210F
-30 to 100C
Color TemperatureLimits
85
7070FDA70NSF
90
Use in: Pneumatic seals, O-Rings, oil seal lips, gaskets,washers and low pressurehydraulic seals. Can be usedwith a back-up ring in higherpressure applications. This isthe most popular O-Ring mate-rial.
Description: General purposeelastomer for use as seal ener-gizer or low pressure applica-tions such as hydraulics andpneumatics. Resistant to oils,hydraulic fluids, water fuels,and gases. Not suited for usein brake fluids. Good abrasionresistance. Good resistance tocompression set. High tensilestrength.
Characteristics: Rubber-likeelastomer. Dulle, matte finish.Some NBR O-Rings have a veryshiny surface.
HardnessMachined
O-RingMoldedO-Ring
Information
SealMaterial
HNBRHighly Saturated
Nitrile Rubber
Also referred to as:HNBR, Hydrogenated
Nitrile,Hydrogenated NBR,
HydrogenatedBuna-N
Black
-13 to 302F
-25 to 150C
Color TemperatureLimits
8570
90
Use in: Seal and gasket applica-tion requiring additional resist-ance to chemicals and slightlyhigher temperatures than canbe handled with NBR. O-Rings,washers, rod and piston seals,back-up rings, and gaskets.
Description: HNBR is achievedby hydrogenated NBR. Greatlyimproved wear and extrusionresistance over standard NBR.Good chemical compatibility andcan be used with oils which haveaggressive additives. Has anextended high temperaturerange
Characteristics: Rubber-likeelastomer. Dull finish
HardnessMachined
O-RingMoldedO-Ring
Information
Material Selection Guide
See page 37 for ahardness scale.
See page 37 for ahardness scale.
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 32
SealMaterial
VITFluoroelastomer
- Viton -
Also referred to as:VIT, Viton, FKM,
Fluorocarbon
Brown
(could alsobe Black,Green -moldedO-Rings)
-4 to 392F
-20 to 200C
Color TemperatureLimits
8575
90
Use in: Tough sealing applica-tions requiring extreme chemicalresistance. O-Rings. Hydraulicseals. Pneumatic seals.
Description: An excellent elas-tomer for use in high tempera-ture applications. Also exhibitsexcellent chemical resistance foruse in harsh environments suchas phosphate esters. Widely usedin applications dealing withextreme temerpature and/orextreme chemicals. It is suitableto use with all chemicals (excep-tion - Skydrol, certain esters andethers) makes it a popular elas-tomer in chemical processing,paper/pulp mills, various chemi-cal, acid and solvent applications.
Characteristics: Rubber-likeelastomer. Noticeably heavierthan NBR. Dull, non-glossy finish.Smells like cinnamon.
HardnessMachined
O-RingMoldedO-Ring
Information
SealMaterial
EPDEPDM Rubber
Also referred to as:EPD, EPR, EP,
Ethylene Propylene
Black
-49 to 300F
-45 to 150C
Color TemperatureLimits
85 70
Use in: Sealing lips of specialoil seals, u-cups, wiper rings,O-Rings, gaskets, washers, androllers.
Description: For use in hightemperature water, steam andbrake fluids. This elastomermust not come in contact withmineral oils or grease. It isused in applications that dealwith acids, weak alkalis. EPD issometimes an accepatable FDAmaterial.
Characteristics: Rubber-likeelastomer. Strong rubbersmell.
HardnessMachined
O-RingMoldedO-Ring
Information
Material Selection Guide
See page 37 for ahardness scale.
See page 37 for ahardness scale.
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 33
SealMaterial
SILSilicone Rubber
Also referred to as:SIL, Silicone,
Silastic
Blue
Orange
sometimeswhite
-75 to 392F
-60 to 200C
Color TemperatureLimits
85 70
Use in: O-Rings, special lowpressure seals, gaskets.
Description: An excellentmaterial generally used forstatic seals with excellent lowand high temperature stabilityand good resistance to aging.Generally not suited for dynam-ic applications. due to poor ten-sile strength and abrasionresistance. Does exhibit excel-lent resistance to extreme tem-perature and is an acceptableFDA material. Typical use forsilicone is in dry heat applica-tions and food processing appli-cations.
Characteristics: Very springy-like rubber-type material.
HardnessMachined
O-RingMoldedO-Ring
Information
SealMaterial
TFVVirgin PTFE
Also referred to as:Teflon, VirginTeflon, PTFE,
TFE, TFV,Polytetra-
fluoroethlene
White
-328 to 500F
-200 to 260C
Color TemperatureLimits
Solid Solid
Use in: Packings, gaskets,seals, washers, spacers, insula-tors, wheels, rollers, bearings,guide rings.
Description: An extremely lowfriction material which remainsstable at both low and hightemperatures. The chemicalresistance of this material isoutstanding. Can be used inapplications with extreme tem-peratures, extreme pressuresand extreme chemicals. SinceTeflon TFV has a tendency tocold flow and has no memory.It can be filled or mixed withglass, bronze, and nickel toenhance its properties.
Characteristics: Semi-rigidplastic material. Most of thetime it is finished by machining.
HardnessMachined
O-RingMoldedO-Ring
Information
Material Selection Guide
See page 37 for ahardness scale.
See page 37 for ahardness scale.
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 34
SealMaterial
NEONeoprene
Also referred to as:Chloroprene
Black
-65 to 250F
-54 to 121C
Color TemperatureLimits
N/A 70
Use in: Common applicationsinclude, refrigeration seals,freon/air conditioning, motormounts, engine coolants.
Description: Good resistanceto petroleum oils. Low com-pression set and good tear andabrasion strength. Good resist-ance to weathering, sunlight,and ozone.
HardnessMachined
O-RingMoldedO-Ring
Information
Material Selection Guide
SealMaterial
PFRPerfluoro-lastomer
Also referred to as:Kalrez
Blackwith
BrownHue
White
-20 to 570F
-30 to 300C
Color TemperatureLimits
N/A
70
75
90
Use in: Most likely applicationenvironments are for aggres-sive acids, solvents, and steam.Could be suited for many non-oxidizing dry process chemicals.
Description: Broad resistanceto chemicals. Low compressionset, strong tear resistance.Virtually indestructible. Aboveaverage outgassing perform-ance in vacuums.
HardnessMachined
O-RingMoldedO-Ring
Information
See page 37 for ahardness scale.
See page 37 for ahardness scale.
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 35
SealMaterial
FSIFluorosilicone
Also referred to as:Silastic L.S.
Blue
-80 to 350F
-62 to 177C
Color TemperatureLimits
N/A 70
Use in: Common applicationsinclude, aircraft fuel systems,jet fuel/gasoline, petroleumoils, synthetic jet oil.
Description: Fluorosilicone is amix of Fluorocarbon (Viton)and Silicone. Wide range offluid and chemical resistance.Large temperature range.
HardnessMachined
O-RingMoldedO-Ring
Information
SealMaterial
AFLAflas
Also referred to as:Tetrafluoroethylene
Propylene
Black
-20 to 400F
-28 to 204C
Color TemperatureLimits
Checkwith
EPM foravail-ablity
75
Use in: Common applicationsinclude, O-Rings for variousfluid seals. Not readily avail-able in other seal forms.Petroleum fluids and steam,amines, brake fluids or phos-phate esters.
Description: Excellent resist-ance to petroleum products,steam, phosphate esters,amines and brake fluids. Broadrange media resistance similarto EPD and Viton.Elastomeric form makes it lowin gas permeability.
Characteristics: Superior heatand wear resistance.Non-abrasive.
Coef. Friction: .15
HardnessMachined
O-RingMoldedO-Ring
Information
Material Selection Guide
See page 37 for ahardness scale.
See page 37 for ahardness scale.
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 36
SealMaterial
EOSArmor-O-Rings
Silicone Core
Also referred to as:Teflon Encapsulated
Silicone O-Rings,PTFE EncapsulatedSilicone O-Rings,
PTFE-FEP EncapsulatedSilicone O-Rings
Orangewith
opaqueshell
-40 to 401F
-40 to 205C
Color TemperatureLimits
N/A 70(core)
Use in: To improve O-Ringperformance in difficultapplications where siliconeO-Rings alone fail.
Description: Armor-O-RingsEOS are produced using a thinPTFE shielded tubing fullyencasing a silicone rubber core.The outer jacket protects theresilient silicone core from thefluids the O-Ring contacts.
Characteristics: Semi-rigidPTFE-FEP tubing fullyencapsulating the silicone corematerial.
Material: PTFE-FEP jacket witha minimum thickness of .008over a silicone core.
HardnessMachined
O-RingMoldedO-Ring
Information
Material Selection Guide
SealMaterial
EOVArmor-O-Rings
Viton Core
Also referred to as:Teflon EncapsulatedViton O-Rings, PTFEEncapsulated VitonO-Rings, PTFE-FEP
Encapsulated VitonO-Rings
Blackwith
opaqueshell
-99 to 401F
-73 to 205C
Color TemperatureLimits
N/A 75(core)
Use in: To improve O-Ringperformance in difficultapplications where Vitonalone fails.
Description: Armor-O-RingsEOV are produced using a thinPTFE shielded tubing fullyencasing a Viton elastomericcore. The outer jacket protectsthe resilient Viton core fromthe fluids which the O-Ringcontacts.
Characteristics: Semi-rigidPTFE-FEP tubing fully encapsu-lating the Viton core material.Endless. No joints.
Material: PTFE-FEP jacket witha minimum thickness of .008over a Viton core.
HardnessMachined
O-RingMoldedO-Ring
Information
See page 37 for ahardness scale.
See page 37 for ahardness scale.
-
Material Hardness Scale
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 37
*The Shore A scale is used to measure the hardness of elastomers, rubber-likematerials, and plastomer materials like polyurethane.
This chart shows the overlapping scales for measuring the hardness of non-metallic materials.
The unit of measurefor all of these scalesis called durometer.
Example:A standard NBRO-Ring is 70durometer Shore A.
The higher the number the harder the material.
OD ID
W
-
O-Ring Material Rankings byTemperature Range
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 38
NEO
500F
450
400
350
300
250
200
150
100
50
0
-50
-100F
Highest
Lowest
NBR EPD FLI TFC VIT SIL PFL
Neo
pre
ne
Nit
rile
EP
DM
Ru
bb
er
Flu
oro
silico
ne
Tefl
on
E
nca
psu
late
d
Vit
on
(
Flu
oro
carb
on
)
Silic
on
e
Kalr
ez
(P
erf
luo
rin
ate
d)
Highest Recommended Temperature
Table Legend
Lowest Recommended Temperature
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 39
O-Ring Material Rankings bySurface Speed Limitation
FLI
Feet
Per
Min
ute
SIL VIT NEO EPD NBR TFC PTFE
Flu
oro
-si
lico
ne
Silic
on
e
Vit
on
(
Flu
oro
carb
on
)
Neo
pre
ne
EP
DM
Ru
bb
er
Nit
rile
Ru
bb
er
Tefl
on
E
nca
psu
late
d*
Cau
tio
n:
Ou
ter
layer
can
wear
pre
matu
rely
PTFE (
Tefl
on
)
Fastest Surface Speed
Table Legend
Slo
wFast
Fast
er
Fast
est
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 40
O-Ring Material Rankings byOil Resistance
EPD NEO SIL NBR FLI VIT
EP
DM
Ru
bb
er
Neo
pre
ne
Silic
on
e Nit
rile
Flu
oro
silico
ne
Vit
on
(
Flu
oro
carb
on
)
Go
od
No
t R
eco
mm
en
ded
Bett
er
Best
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 41
O-Ring Material Rankings byAbrasion Resistance
TFV
12
11
10
9
8
7
6
5
4
3
2
1
Best
Least
SIL EPD FLI NEO NBR
TFV
an
d O
ther
PTFE M
ate
rials
Silic
on
e
EP
DM
Ru
bb
er
Flu
oro
silico
ne
Neo
pre
ne
Nit
rile
VIT
Vit
on
-
Flu
oro
carb
on
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 42
O-Ring Material Rankings byTear Resistance
(lb/inch of thickness)
SIL
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Best
Least
FLI VIT NEO EPD NBR
Nit
rile
EP
DM
Ru
bb
er
Neo
pre
ne
Vit
on
(
Flu
oro
carb
on
)
Flu
oro
silico
ne
Silic
on
e
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 43
O-Ring Material Rankings byRelative Price
NBR
HighestPrice
LowestPrice
10
9
8
7
6
5
4
3
2
1
0NEO EPD SIL VIT FLI TFC PFL
Nit
rile
Neo
pre
ne
EP
DM
Ru
bb
er
Silic
on
e
Vit
on
(
Flu
oro
carb
on
)
Flu
oro
silico
ne
Tefl
on
E
nca
psu
late
d
Kalr
ez
(P
erf
luo
rin
ate
d)
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 44
Fluid Compatibility Guide
Fluid NameAbietic AcidAcetaldehydeAcetamideAcetanilideAcetate of LimeAcetic Acid, 30%Acetic Acid, GlacialAcetic Acid, HotAcetic AnhydrideAcetic EsterAcetic OxideAcetoacetic AcidAcetoneAcetone CyanohydrinAcetonitrileAcetophenoneAcetyl AcetoneAcetyl AcetonicAcetyl BromideAcetyl ChlorideAcetyl OxideAcetyl PropaneAcetylene TetrabromideAcetylene TetracholorideAcetylene, GaAcroleinAcrylic AcidAcryonitrileAdipic AcidAero LubriplateAero Shell 17 GreaseAuro Shell 1AC GreaseAero Shell 750 GreaseAero Shell 7A GreaseAerosafe 2300
X42X2122442242144444242423X41122424
X11X112X222X11111143221411342444441
2423434X4444444444X1441114442111114
X41552444X4545544XX1XX223XX41111413
X313XX224XX343X44X44XX4413241111114
X41X223X343444344444344413241111214
1211X11X1XX111111X11XX1X11111111111
X44XX444442X44X44444XX4X24X4X111414
X23X1114325X31X44XX3XX4X3XX4X222223
X11X1X1X111X1XX111X1111X11X11XXXXX2
54255533245545144521551115422111112
Compatibility Rating1 = Satisfactory 4 = Not Recommended2 = Fair X = Data Not Available3 = Poor = Contact EPM For Info
This is to be used as a guide only. These aregeneral guidelines. Users must conduct func-tional tests to determine the suitability of anycompound for a particular application.EPM, Inc. assumes no responsibility.
Neo
pre
ne
(N
EO
)
EP
DM
Ru
bb
er
(EP
D)
Flu
oro
carb
on
/V
ito
n
(V
IT)
Flu
oro
silico
ne (
FLI)
Hyd
rog
en
ate
d N
itri
le (
HN
BR
)
Nit
rile
/B
un
a-N
(N
BR
)
Perf
luo
roela
sto
mer
(PFR
)
Po
lyu
reth
an
e (
HP
U)
Silic
on
e (
SIL
)
Tefl
on
(
PTFE)
Tefl
on
E
nca
p.
Silic
on
e (
EO
S)
Tefl
on
E
nca
p.
Vit
on
(
EO
V)
Afl
as
(A
FL)
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 45
Fluid Compatibility Guide
Fluid NameAerosafe 2300WAerozene 50Air, Below 200FAir, 200F to 300FAir, 400F to 500FAldehydeAlkazeneAlkenes (Olefin Hyrdocarbons)Alkyl AcetoneAlkyl AlcoholAlkyl AmineAlkyl Aryl SulfonicsAlkyl BenzeneAlkyl ChlorideAlkyl Napthalene Sulfonic AcidAlkyl SulfideAllyl ChlorideAllylidene DiacetateAlpha PicoleneAluminum AcetateAluminum Ammonium SulphateAluminum BromideAluminum ChlorateAluminum ChlorideAluminum FluorideAluminum FormateAluminum HydroxideAluminum LinoleateAluminum NitrateAluminum OxalateAluminum PhosphateAluminum Potassium SulfateAluminum SaltsAluminum Sodium SulfateAluminum Sulfate
4412434414444444411222X22X1X2X12222
1112414414444444411111X11X1X1X11111
441XX42214412221233411X1141X1X11111
34114X2111111212411451X11X1XXXX11X1
42134X41311122121332113113211311131
4312444131114212233421X1142X1X11111
121XXX111111X1111111X1111X1X1111111
4433434141114313X444X3X23X2X3XXX312
3411X13222224X2X1224X1X22X1X2X11111
2X1XXX1XXXXX1XXXXXX111X11X1X1X111X1
2112XX2XXXXX2XXX1XX1X1X11X1X1X1X121
Compatibility Rating1 = Satisfactory 4 = Not Recommended2 = Fair X = Data Not Available3 = Poor = Contact EPM For Info
This is to be used as a guide only. These aregeneral guidelines. Users must conduct func-tional tests to determine the suitability of anycompound for a particular application.EPM, Inc. assumes no responsibility.
Neo
pre
ne
(N
EO
)
EP
DM
Ru
bb
er
(EP
D)
Flu
oro
carb
on
/V
ito
n
(V
IT)
Flu
oro
silico
ne (
FLI)
Hyd
rog
en
ate
d N
itri
le (
HN
BR
)
Nit
rile
/B
un
a-N
(N
BR
)
Perf
luo
roela
sto
mer
(PFR
)
Po
lyu
reth
an
e (
HP
U)
Silic
on
e (
SIL
)
Tefl
on
(
PTFE)
Tefl
on
E
nca
p.
Silic
on
e (
EO
S)
Tefl
on
E
nca
p.
Vit
on
(
EO
V)
Afl
as
(A
FL)
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 46
Fluid Compatibility Guide
Fluid NameAmbrex 33 Ambrex 830 Amines Aminoanthraquinone Aminoazobenzene Aminobenoic Acid Ammonia and Lithium in Metal Solution Ammonia Gas, Cold Ammonia Gas, Hot Ammonia Liquid Ammonia, Anhydrous Ammonium Acetate Ammonium Alum Ammonium Arsenate Ammonium Benzoate Ammonium Bicarbonate Ammonium Bifluoride Ammonium Bromide Ammonium CarbamateAmmonium Carbonate Ammonium Chloride Ammonium Chromic Sulfate Ammonium Dichromate Ammonium Diphosphate Ammonium Fluoride Ammonium Fluoride Acid Ammonium Fluorosilicate Ammonium Formate Ammonium Hydrate Ammonium Hydroxide Ammonium Hyposulphite Ammonium Iodide Ammonium Lactate Ammonium Metaphosphate Ammonium Molybdentate
224XXX4114111XX14XX2211122XX131X111
432XXX2112112XX21XX11X111XXXX11X111
114XXX4444442XX41XX11XX11XXXX31X313
314XXX44444XXXXXXXXX3XXXXXXXX1XX1X1
114XXX221423X333X1341X3314X3X4X1333
114XXX2212212XX11XX221112XXX141X313
11111X411111X11111111X1X1X11X1X1111
214XXX442443XXX3XXX12XXXXXXXX4XX4X4
422XXX42112XXXXXXXX33XX1XXXXX1XX2X2
21XXXXX111111XX11XX111XX11XX111XX1X
11232221123XX2X1X1X11XXX2X1XX1X2XXX
Compatibility Rating1 = Satisfactory 4 = Not Recommended2 = Fair X = Data Not Available3 = Poor = Contact EPM For Info
This is to be used as a guide only. These aregeneral guidelines. Users must conduct func-tional tests to determine the suitability of anycompound for a particular application.EPM, Inc. assumes no responsibility.
Neo
pre
ne
(N
EO
)
EP
DM
Ru
bb
er
(EP
D)
Flu
oro
carb
on
/V
ito
n
(V
IT)
Flu
oro
silico
ne (
FLI)
Hyd
rog
en
ate
d N
itri
le (
HN
BR
)
Nit
rile
/B
un
a-N
(N
BR
)
Perf
luo
roela
sto
mer
(PFR
)
Po
lyu
reth
an
e (
HP
U)
Silic
on
e (
SIL
)
Tefl
on
(
PTFE)
Tefl
on
E
nca
p.
Silic
on
e (
EO
S)
Tefl
on
E
nca
p.
Vit
on
(
EO
V)
Afl
as
(A
FL)
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 47
Fluid Compatibility Guide
Fluid NameAmmonium Nitrate Ammonium Nitrite Ammonium Oxalate Ammonium Perchlorate Ammonium Persulfate Ammonium Phosphate Ammonium Phosphate, Dibasic Ammonium Phosphate, Monobasic Ammonium Phosphate, Tribasic Ammonium Salts Ammonium Sulfamate Ammonium Sulfate Ammonium Sulfide Ammonium Sulfite Ammonium Thiocyanate Ammonium Thioglycolate Ammonium Thiosulfate Ammonium Tungstate Ammonium Valerate Amyl Acetate Amyl Acetic Ester Amyl Acetone Amyl Alcohol Amyl Borate Amyl Bromide Amyl Carbinol Amyl Chloride Amyl Chloronaphthalene Amyl Ether Amyl Hydrate Amyl Hydride Amyl Iodide Amyl Laurate Amyl Mercaptan Amyl Naphthalene
111X421131X1111X1XX44X214244X214X44
111X211111X1111X1XX12X1443444X44X44
11XX11111141211X11X444212211XX1X111
3XXX14X4X3X1XXXXXXX4XX1XXX22X11XX21
11334111113113333334XX21X114XXX4X24
11XX111111X111111111XX11XX11XXXXX11
1111111XX11111111111XX11XX11XXXXX11
X1XX42X2XXX12X2XXXX4XX4XX434XXXXX34
32XX411111X1XXXXXXX44X44X244X44XXX4
11XX1X1111X111XXXXX1111111111111XX1
1222121221X11XXXXXX4XX11XX12XXXXXX2
Compatibility Rating1 = Satisfactory 4 = Not Recommended2 = Fair X = Data Not Available3 = Poor = Contact EPM For Info
This is to be used as a guide only. These aregeneral guidelines. Users must conduct func-tional tests to determine the suitability of anycompound for a particular application.EPM, Inc. assumes no responsibility.
Neo
pre
ne
(N
EO
)
EP
DM
Ru
bb
er
(EP
D)
Flu
oro
carb
on
/V
ito
n
(V
IT)
Flu
oro
silico
ne (
FLI)
Hyd
rog
en
ate
d N
itri
le (
HN
BR
)
Nit
rile
/B
un
a-N
(N
BR
)
Perf
luo
roela
sto
mer
(PFR
)
Po
lyu
reth
an
e (
HP
U)
Silic
on
e (
SIL
)
Tefl
on
(
PTFE)
Tefl
on
E
nca
p.
Silic
on
e (
EO
S)
Tefl
on
E
nca
p.
Vit
on
(
EO
V)
Afl
as
(A
FL)
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 48
Fluid Compatibility Guide
Fluid Name
Compatibility Rating1 = Satisfactory 4 = Not Recommended2 = Fair X = Data Not Available3 = Poor = Contact EPM For Info
Neo
pre
ne
(N
EO
)
EP
DM
Ru
bb
er
(EP
D)
Flu
oro
carb
on
/V
ito
n
(V
IT)
Flu
oro
silico
ne (
FLI)
Hyd
rog
en
ate
d N
itri
le (
HN
BR
)
Nit
rile
/B
un
a-N
(N
BR
)
Perf
luo
roela
sto
mer
(PFR
)
Po
lyu
reth
an
e (
HP
U)
Silic
on
e (
SIL
)
Tefl
on
(
PTFE)
Tefl
on
E
nca
p.
Silic
on
e (
EO
S)
Tefl
on
E
nca
p.
Vit
on
(
EO
V)
Afl
as
(A
FL)
Amyl Nitrate Amyl Nitrite Amyl Oleate Amyl Phenol Amyl Phthalate Amyl Propionate Amylene AN-0-3 Grade M AN-0-366 AN-0-6AN-VV-0-366B HydraulicAnderol Diester ANG-25 (Diester Base) ANG-25 (Glyceral Ester) Aniline Aniline Dyes Aniline Hydrochloride Aniline Oils Aniline Sulfate Aniline Sulfite Animal Fats (Lards) Animal Fats (Oils) Ansul Ether 161 or 181 Anthracene Anthranilic Acid Anthraquinone Antifreeze Solutions Antimony Chloride Antimony Pentachloride Antimony Pentafluoride Antimony Salts Antimony Sulfate Antimony Tribromide Antimony Trichloride Antimony Trifluoride
XXXXXX12222442434111324XXX344X1X33X
2XXXXX44444441222211113XXX144X1X42X
XXXX3211111111222133114XXX211XXX1XX
XXXXXXX1111222322111113XXX412X1X2XX
33XXX1X11112224441331131XX312XXX211
1X244X21111222444133113XXX112X1X22X
11XXX1X111X1111111111X1111X112X1112
XXXXXXX1113444444144332XXX414X1X22X
XX4XXXX24444224XX1222X4XXX344X1X4XX
XX1X1X1XXXXXXX111XXX111XXX1111XXXXX
XXXXXXX11112221111XX111XXX111XXXXXX
This is to be used as a guide only. These aregeneral guidelines. Users must conduct func-tional tests to determine the suitability of anycompound for a particular application.EPM, Inc. assumes no responsibility.
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 49
Fluid Compatibility Guide
Fluid Name
Compatibility Rating1 = Satisfactory 4 = Not Recommended2 = Fair X = Data Not Available3 = Poor = Contact EPM For Info
Neo
pre
ne
(N
EO
)
EP
DM
Ru
bb
er
(EP
D)
Flu
oro
carb
on
/V
ito
n
(V
IT)
Flu
oro
silico
ne (
FLI)
Hyd
rog
en
ate
d N
itri
le (
HN
BR
)
Nit
rile
/B
un
a-N
(N
BR
)
Perf
luo
roela
sto
mer
(PFR
)
Po
lyu
reth
an
e (
HP
U)
Silic
on
e (
SIL
)
Tefl
on
(
PTFE)
Tefl
on
E
nca
p.
Silic
on
e (
EO
S)
Tefl
on
E
nca
p.
Vit
on
(
EO
V)
Afl
as
(A
FL)
Antimony TrioxideAntinmony TrifluorideApple AcidAqua RegiaArachidic AcidArgonArochlor 1248Arochlor 1254Arochlor 1260Aromatic AlcoholAromatic FuelsAromatic HydrocarbonsAromatic SpiritsAromatic TarAromatic VinegarArsenic AcidArsenic ButterArsenic ChlorideArsenic SaltsArsenic TrichlorideArsenic TrioxideArsenic TrisulfateArsineAscorbic AcidAskarel Transformer OilAspartic AcidAsphaltASTM Method D-471-1ASTM Method D-471-2ASTM Method D-471-3ASTM Reference Fuel AASTM Reference Fuel BASTM Reference Fuel CASTM Reference Fuel DASTM Reference Oil No. 1
3324X4441344XX2211X1XXXX4X3XXX24441
1142X1222344XX1144X4XXXX4X444444444
11112111111111114424XXX1131XXX11221
XX13X2211X21XXX1XXXXXXXX2X211122211
X114X1341X2XXXX1XXX111X323211111221
1114X1341324333133X1XXXX2X211111231
121111111X11XXX1XXX11X1111111111111
XXX4X1241X43XX23XX2XXXXX4X212222421
XX24X2331X43XX11XXXXXXXX4X433344441
XX11XXXXX1X111111111XXXX1XXXXX111X1
11X3X1111X22XXX1XXX4XXXX1X2XXX34441
This is to be used as a guide only. These aregeneral guidelines. Users must conduct func-tional tests to determine the suitability of anycompound for a particular application.EPM, Inc. assumes no responsibility.
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 50
Fluid Compatibility Guide
Fluid Name
Compatibility Rating1 = Satisfactory 4 = Not Recommended2 = Fair X = Data Not Available3 = Poor = Contact EPM For Info
Neo
pre
ne
(N
EO
)
EP
DM
Ru
bb
er
(EP
D)
Flu
oro
carb
on
/V
ito
n
(V
IT)
Flu
oro
silico
ne (
FLI)
Hyd
rog
en
ate
d N
itri
le (
HN
BR
)
Nit
rile
/B
un
a-N
(N
BR
)
Perf
luo
roela
sto
mer
(PFR
)
Po
lyu
reth
an
e (
HP
U)
Silic
on
e (
SIL
)
Tefl
on
(
PTFE)
Tefl
on
E
nca
p.
Silic
on
e (
EO
S)
Tefl
on
E
nca
p.
Vit
on
(
EO
V)
Afl
as
(A
FL)
ASTM Reference Oil No. 2ASTM Reference Oil No. 3ASTM Reference Oil No. 4ASTM Reference Oil No. 5Astra OilATL-857Atlantic Dominion FAtlantic Utro Gear-EP LubricantAurex 903RAutomatic Transmission FLuidAutomotive Brake FluidAviation GasolineAxarel 9100AzovenzeneBaking SodaBardol BBarium CarbonateBarium ChlorateBarium ChlorideBarium CyanideBarium FluorideBarium HydrateBarium HydroxideBarium IodideBarium MonohydrateBarium MonosulfideBarium NitrateBarium OxideBarium PeroxideBarium PolysulfideBarium SaltsBarium SulfateBarium SulfideBasic Iron SulfateBayol 35
234X24222224XX141X21212X111XXX12212
444444444414XX141X11411XX11XXX111X4
111111XX1144XX111111311XXX1XXX111X1
112XX21X4X41XX12XX1XXX1X1X1XXX111X1
1121X211113XXX143311XX11XX3133111X1
112112111131XX141X13111X111XXX11111
1111XXXX111111111111XX111X111X111X1
224X34211242XX142X1X114XX12XXX111X3
434X44444434XX14XX1X411X122XXX121X4
11XX1XXXX111XX11XX1XX11X111XXX1111X
2321X1221113XXX21X11XX11XXX1XX111X1
This is to be used as a guide only. These aregeneral guidelines. Users must conduct func-tional tests to determine the suitability of anycompound for a particular application.EPM, Inc. assumes no responsibility.
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 51
Fluid Compatibility Guide
Fluid Name
Compatibility Rating1 = Satisfactory 4 = Not Recommended2 = Fair X = Data Not Available3 = Poor = Contact EPM For Info
Neo
pre
ne
(N
EO
)
EP
DM
Ru
bb
er
(EP
D)
Flu
oro
carb
on
/V
ito
n
(V
IT)
Flu
oro
silico
ne (
FLI)
Hyd
rog
en
ate
d N
itri
le (
HN
BR
)
Nit
rile
/B
un
a-N
(N
BR
)
Perf
luo
roela
sto
mer
(PFR
)
Po
lyu
reth
an
e (
HP
U)
Silic
on
e (
SIL
)
Tefl
on
(
PTFE)
Tefl
on
E
nca
p.
Silic
on
e (
EO
S)
Tefl
on
E
nca
p.
Vit
on
(
EO
V)
Afl
as
(A
FL)
Bayol DBeerBeet Sugar LiquidsBeet Sugar LiquorsBenzal AlcoholBenzal ChlorideBenzaldehydeBenzanthroneBenzeneBenzene CarbinolBenzene HexachlorideBenzene Sulfonic AcidBenzidineBenzilBenzilic AcidBenzine (Ligroin)BenzochlorideBenzoic AcidBenzoinBenzolBenzonitrileBenzophenoneBenzoquinoneBenzotrichlorideBenzotrifluorideBenzoyl ChlorideBenzoyl PeroxideBenzoylsulfonic AcidBenzyl AcetateBenzyl AlcoholBenzyl AmineBenzyl BenzoateBenzyl BromideBenzyl Butyl PhthalateBenzyl Chloride
22223X4X44X2XXX442X4X44XX4X4X4X4X14
4111XX1X42X4XXX414X4X221X4X4X2X2X14
11X11X422421XXX1X1X2X211X2X1X1X1X32
1111XX4X2XX2XXX112X2X1XXX2X2X2X1X12
1111XX424XX42221442434X44XX234X4434
1111444X44X4XXX144X4X4X4X4X244X4X34
1111X1211X111X11X111111111111111111
4244XX4X44X4XXX3X4X4X444X4X3X4XXX44
4111XX4X43X4XXX4X4X4X4XXX4XXX2XXX24
X1XX111X11X1XXX1X1X1XXX1XXXXX1XXXX1
1111XX2X3XX1XXX211X3X12312XXX2X22X2
This is to be used as a guide only. These aregeneral guidelines. Users must conduct func-tional tests to determine the suitability of anycompound for a particular application.EPM, Inc. assumes no responsibility.
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 52
Fluid Compatibility Guide
Fluid Name
Compatibility Rating1 = Satisfactory 4 = Not Recommended2 = Fair X = Data Not Available3 = Poor = Contact EPM For Info
Neo
pre
ne
(N
EO
)
EP
DM
Ru
bb
er
(EP
D)
Flu
oro
carb
on
/V
ito
n
(V
IT)
Flu
oro
silico
ne (
FLI)
Hyd
rog
en
ate
d N
itri
le (
HN
BR
)
Nit
rile
/B
un
a-N
(N
BR
)
Perf
luo
roela
sto
mer
(PFR
)
Po
lyu
reth
an
e (
HP
U)
Silic
on
e (
SIL
)
Tefl
on
(
PTFE)
Tefl
on
E
nca
p.
Silic
on
e (
EO
S)
Tefl
on
E
nca
p.
Vit
on
(
EO
V)
Afl
as
(A
FL)
Benzyl PhenolBenzyl SalicylateBeryllium ChlorideBeryllium FluorideBeryllium OxideBeryllium SulfateBeta CaroteneBismuth CarbonateBismuth NitrateBismuth OxychlorideBitternBlack LiquorBlack Point 77Black Sulfate LiquorBlast-Furnace GasBleach LiquorBleach SolutionsBloodBoraxBorax SolutionBordeaux MixtureBoric AcidBoric OxideBorneolBornyl AcetateBornyl ChlorideBornyl FormateBoron FLuids (HEF)Boron PhosphateBoron TribromideBoron TrichlorideBoron TrifluorideBoron TrioxideBrayco 885 (MIL-L-6085A)Brayco 910
44XXXX41XXX1314441X222XXXXX4XXXXX22
44XXXXX1XXX11141111111XXXXX4XXXXX41
11XXXX11XXX11111X21111X2XXX1XXXXX14
22XXXXXXXXXX32222X2221XXXXX2XXXXX14
224113X333X21X42XX2121322222XXXXX22
22XXXX11XXX11144432211XXXXX2XXXXX22
111111XXX1131X111X1X11111X111111111
33XXXX1XXXX43X44421141XXXXX4XXXXX33
XXXXXXXXXXX13212222221XXXXX4XXXXX34
XXXXXXXXXXX1X111X1X211XXXXXXXXXXXXX
XX111XXXXXX21X11XX1X11XXXXX2XXXXX23
This is to be used as a guide only. These aregeneral guidelines. Users must conduct func-tional tests to determine the suitability of anycompound for a particular application.EPM, Inc. assumes no responsibility.
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 53
Fluid Compatibility Guide
Fluid Name
Compatibility Rating1 = Satisfactory 4 = Not Recommended2 = Fair X = Data Not Available3 = Poor = Contact EPM For Info
Neo
pre
ne
(N
EO
)
EP
DM
Ru
bb
er
(EP
D)
Flu
oro
carb
on
/V
ito
n
(V
IT)
Flu
oro
silico
ne (
FLI)
Hyd
rog
en
ate
d N
itri
le (
HN
BR
)
Nit
rile
/B
un
a-N
(N
BR
)
Perf
luo
roela
sto
mer
(PFR
)
Po
lyu
reth
an
e (
HP
U)
Silic
on
e (
SIL
)
Tefl
on
(
PTFE)
Tefl
on
E
nca
p.
Silic
on
e (
EO
S)
Tefl
on
E
nca
p.
Vit
on
(
EO
V)
Afl
as
(A
FL)
Bret 710BrineBrine SeawaterBrom - 113Brom - 114Bromic AcidBromineBromine AnhydrousBromine PentafluorideBromine TrifluorideBromine WaterBromobenezeneBromochloromethaneBromotrifluoromethane (F-13B1)Buffered Oxide EtchantsBunker OilBunkers C (Fuel Oil)ButadieneButaneButane, 2. 2-DimethylButanol (Butyl Alcohol)Butene 2-Ethyl (1-Butene, 2-Ethyl)Butter-Animal FatButyl Acetaten-Butyl AcetateButyl Acetyl RicinoleateButyl AcrylateButyl Alcoholn-butyl Alcoholtert-Butyl AlcoholButyl AldehydeButyl AmineButyl Benzoaten-Butyl BenzoateButyl Benzyl Phthalate (BBP)
22342X4444444XX4443224344241123444X
11244X44442421X4444424122142122411X
X1XXXX1144211XX1131XXXX441411144113
411XXX22442222X111211314424112X411X
2113234X4444XXX1X4111114424112X133X
21232X44444441X11411111442411243444
X1XXX11122111211X11XXX11111111X1111
3X2XXX4X4444XXX22414X43444X44434XXX
41144X44444444X2X44424244X122234XXX
XXXXXXX1X1X11XX1XX4XXXXX11XX1X11XX1
21133X11443233X2X222111X414111X2XXX
This is to be used as a guide only. These aregeneral guidelines. Users must conduct func-tional tests to determine the suitability of anycompound for a particular application.EPM, Inc. assumes no responsibility.
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 54
Fluid Compatibility Guide
Fluid Name
Compatibility Rating1 = Satisfactory 4 = Not Recommended2 = Fair X = Data Not Available3 = Poor = Contact EPM For Info
Neo
pre
ne
(N
EO
)
EP
DM
Ru
bb
er
(EP
D)
Flu
oro
carb
on
/V
ito
n
(V
IT)
Flu
oro
silico
ne (
FLI)
Hyd
rog
en
ate
d N
itri
le (
HN
BR
)
Nit
rile
/B
un
a-N
(N
BR
)
Perf
luo
roela
sto
mer
(PFR
)
Po
lyu
reth
an
e (
HP
U)
Silic
on
e (
SIL
)
Tefl
on
(
PTFE)
Tefl
on
E
nca
p.
Silic
on
e (
EO
S)
Tefl
on
E
nca
p.
Vit
on
(
EO
V)
Afl
as
(A
FL)
Butyl Butyraten-Butyl Butyrateter-Butyl CaltecholButyl CarbitolButyl CellosolveButyl Cellosolve AcetateButyl Cellosolve AdipateButyl ChlorideButyl Ethern-Butyl EtherButyl LactateButyl LaurateButyl Mercaptantert-Butyl MercaptanButyl OleateButyl OxalateButyl StearateButyleneButyraldenhydeButyric AcidButyric AnhydrideButryl ChlorideButyrolacetoneButyroyl ChlorideCadmium ChlorideCadmium CyanideCadmium NitrateCadmium OxideCadmium SulfateCadmium SulfideCalcine LiquorsCalcium AcetateCalcium AluminateCalcium ArsenateCalcium Benzoate
44234X4X44XXX4414344X41XX2XXXX22X14
1121222X33XX44214432X41XX1XXXX11X14
11X242XX44X24X131143X13XX12XXX14131
1114422X33XXXX212242X21XX1XXXX14X12
XX443343333344432442323231333312X32
4444344433XX44432144323XX2XXXX12132
111111X1111111111121111111111111X11
XX444X4X22XXX4442344X34XXXXXXX44X43
XXX4422X44XX4422X444XX2XXXXXXXX4X2X
11X11XXXXXXXXX1XXX11XXXXX1XXXX1X1XX
XXX2322XXXXX1X2X2X21XXXXX1XXXX12XXX
This is to be used as a guide only. These aregeneral guidelines. Users must conduct func-tional tests to determine the suitability of anycompound for a particular application.EPM, Inc. assumes no responsibility.
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 55
Fluid Compatibility Guide
Fluid Name
Compatibility Rating1 = Satisfactory 4 = Not Recommended2 = Fair X = Data Not Available3 = Poor = Contact EPM For Info
Neo
pre
ne
(N
EO
)
EP
DM
Ru
bb
er
(EP
D)
Flu
oro
carb
on
/V
ito
n
(V
IT)
Flu
oro
silico
ne (
FLI)
Hyd
rog
en
ate
d N
itri
le (
HN
BR
)
Nit
rile
/B
un
a-N
(N
BR
)
Perf
luo
roela
sto
mer
(PFR
)
Po
lyu
reth
an
e (
HP
U)
Silic
on
e (
SIL
)
Tefl
on
(
PTFE)
Tefl
on
E
nca
p.
Silic
on
e (
EO
S)
Tefl
on
E
nca
p.
Vit
on
(
EO
V)
Afl
as
(A
FL)
Calcium BicarbonateCalcium BichromateCalcium BisulfideCalcium BisulfiteCalcium BromideCalcium CarbideCalcium CarbonateCalcium ChlorateCalcium ChlorideCalcium ChromateCalcium CyanamideCalcium CyanideCalcium DisulfateCalcium FluorideCalcium HydrateCalcium HydrideCalcium HydrosulfideCalcium HydroxideCalcium HypochloriteCalcium HypophosphiteCalcium Hydrogen SulfiteCalcium LactateCalcium NitrateCalcium OxalateCalcium OxideCalcium PermanganteCalcium PeroxideCalcium PhenosulfateCalcium PhosphateCalcium PropionateCalcium SaltsCalcium SilicateCalcium StearateCalcium SufamateCalcium Sulfate
1X131X122XX13X1XX24XXX1X2XXX2X11XX4
1X141X111XX11X1XX11X4X1X1XXX1X11XX1
3X31111X1XX11X1XX11X1X1X1XXX1X11XX2
1X131X1X1XXX1XXXX12X1X1XXXXX1X1XXXX
3X31121311X1X3X3X123X3131XX31311223
3X311X111XX11X1XX12X4X1X1XXX1X11XX1
111111111111X1X111111X11111X1111111
4X411X421XXX1X1XX144XX1X2XXX1X1XXX2
2X231X4X1XX12XXXX12X1X2X3XXX1X2XXXX
X1X1XX1X1XX11XXXX11XXX1XXXXXXX11XX1
XXX11X1X1XX1X1X1X11X1X1X1XXX1X11XXX
This is to be used as a guide only. These aregeneral guidelines. Users must conduct func-tional tests to determine the suitability of anycompound for a particular application.EPM, Inc. assumes no responsibility.
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 56
Fluid Compatibility Guide
Fluid Name
Compatibility Rating1 = Satisfactory 4 = Not Recommended2 = Fair X = Data Not Available3 = Poor = Contact EPM For Info
Neo
pre
ne
(N
EO
)
EP
DM
Ru
bb
er
(EP
D)
Flu
oro
carb
on
/V
ito
n
(V
IT)
Flu
oro
silico
ne (
FLI)
Hyd
rog
en
ate
d N
itri
le (
HN
BR
)
Nit
rile
/B
un
a-N
(N
BR
)
Perf
luo
roela
sto
mer
(PFR
)
Po
lyu
reth
an
e (
HP
U)
Silic
on
e (
SIL
)
Tefl
on
(
PTFE)
Tefl
on
E
nca
p.
Silic
on
e (
EO
S)
Tefl
on
E
nca
p.
Vit
on
(
EO
V)
Afl
as
(A
FL)
Calcium SulfideCalcium SulfiteCalcium ThiocyanateCalcium ThiosulfateCalcium TungstateCalcuim GluconateCaliche LiquorsCampheneCamphorCane Sugar LiquorsCaproic AcidCaproic AldehydeCaprolactumCarbamateCarbitolCarbolic Acid (Phenol)Carbon BisulfideCarbon Dioxide, DryCarbon Dioxide, WetCarbon DisulfideCarbon FluoridesCarbon MonoxideCarbon SulfideCarbon TetrabromideCarbon TetrachlorideCarbon TetraflourideCarbonated BeveragesCarbonic AcidCarbonic AnhydrideCaseinCastor OilCatsupCaustic LimeCaustic PotashCaustic Soda
21X1XX2XX2XXX2244224X41X44141212241
11X1XX1X11X212244222X1XX4211112X111
11X1XX12212441211111X14X1X111111114
11X1XX1XX1X4X1222222X2XX3X21X11X132
11323112211X1324411221XX22X1X31X132
11X2XX1X11XX1324X11XX11X44121111122
1111111111111111111111X11XX1X11X111
11X1XX1XX4XXX444X1XXX1XX41211X14XX4
21X1XX2XX1X2X1244222X1XX4X31111X132
11X1XX1XX1XXX1X11111X11X1XX1111X111
11X1XX1X11X32111211121XX42X1XX1X111
This is to be used as a guide only. These aregeneral guidelines. Users must conduct func-tional tests to determine the suitability of anycompound for a particular application.EPM, Inc. assumes no responsibility.
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 57
Fluid Compatibility Guide
Fluid Name
Compatibility Rating1 = Satisfactory 4 = Not Recommended2 = Fair X = Data Not Available3 = Poor = Contact EPM For Info
Neo
pre
ne
(N
EO
)
EP
DM
Ru
bb
er
(EP
D)
Flu
oro
carb
on
/V
ito
n
(V
IT)
Flu
oro
silico
ne (
FLI)
Hyd
rog
en
ate
d N
itri
le (
HN
BR
)
Nit
rile
/B
un
a-N
(N
BR
)
Perf
luo
roela
sto
mer
(PFR
)
Po
lyu
reth
an
e (
HP
U)
Silic
on
e (
SIL
)
Tefl
on
(
PTFE)
Tefl
on
E
nca
p.
Silic
on
e (
EO
S)
Tefl
on
E
nca
p.
Vit
on
(
EO
V)
Afl
as
(A
FL)
CelloguardCellosolveCellosolve AcetateCellosolve ButylCellulose AcetateCellulube A60Cellutherm 2505ACement, PortlandCerium SulfateCerous ChlorideCerous FluorideCerous NitrateCetane (Hexadecane)Cetyl AlcoholChassis GreaseChaulmoogric AcidChina Wood OilChloralChloramineChloranthraquinoneChlordaneChlorextolChloric AcidChloride/Chlorate of LimeChlorinated NapthaleneChlorianted Salt BrineChlorine (Wet)Chlorine DioxideChlorine TrifluorideChlorine WaterChloroacetic AcidChloroacetoneChloroacetonitrileChloroacetyl Chloridem-Chloroaniline
X444444X1111243X2XX432X4X44444433XX
1222X2411111444X4XX444X144X44321XX2
144X431133X311XX1X4111X121114144XXX
1444X32X111131XX2XX222X121224X44XXX
1444342X333311XX13X22232X4344344XXX
144424213333111X1XX222X344X443443X4
111X1111111111X11111111111122111X11
X444444X444441XX3XX3X4X3X4444444XXX
1444X34X2222424X4XXX44X2444344X4XXX
XXXXXXXXXXXX1X1X1XXX1XX1X1X11X11XXX
1132X211XXXX1XXX2XXX11X141334124XX2
This is to be used as a guide only. These aregeneral guidelines. Users must conduct func-tional tests to determine the suitability of anycompound for a particular application.EPM, Inc. assumes no responsibility.
-
The Seal Mans O-Ring Handbook
112-G West Burke Street Stockbridge, GA 30281Phone: (800) 659-5050 Fax: (888) 353-7325 Web: www.epm.com 58
Fluid Compatibility Guide
Fluid Name
Compatibility Rating1 = Satisfactory 4 = Not Recommended2 = Fair X = Data Not Available3 = Poor = Contact EPM For Info
Neo
pre
ne
(N
EO
)
EP
DM
Ru
bb
er
(EP
D)
Flu
oro
carb
on
/V
ito
n
(V
IT)
Flu
oro
silico
ne (
FLI)
Hyd
rog
en
ate
d N
itri
le (
HN
BR
)
Nit
rile
/B
un
a-N
(N
BR
)
Perf
luo
roel