Original BMW Accessories. Installation Instructions....Installation information - All...

30
01 29 2 350 388 04/2016 © BMW AG, Munich (V/Z) 1 Original BMW Accessories. Installation Instructions. 04/2016 M Performance Aerodynamics Package Retrofit Kit. BMW 4 Series Coupé (F32) BMW 4 Series Convertible (F33) BMW 4 Series Gran Coupé (F36) Retrofit kit number Installation time Installation time see table. This may vary depending on the condition of the vehicle and the equipment in it. The installation time shown does not include any time spent on programming/coding. The calculation of the total costs for the programming time must be factored into the calculation of retrofitting costs (no invoicing via warranty). Important information These installation instructions are primarily designed for use within the BMW dealership organisation and by au- thorised BMW service companies. These installation instructions are intended for use by qualified specialist staff trained on BMW vehicles with the relevant expert knowledge. All work must be completed using the latest BMW repair manuals, wiring diagrams, servicing manuals and work instructions, in a rational order, using the prescribed tools (special tools) and observing current health and safety regulations. If you experience installation or function problems, restrict troubleshooting to approx. 0.5 hours for mechanical work and 1.0 hour for electrical work. To avoid unnecessary extra work and/or costs, send an inquiry straight away to the technical parts support team via the Aftersales Assistance Portal (ASAP). Single-sided Twin-pipe Twin-sided Single-pipe Component designation Type Installa- tion time (h) 51 19 2 334 543 51 19 2 339 218 Rear diffuser, matt black F32/F33/F36 0.25 51 19 2 334 548 Carbon front add-on section F32/F36 1.00 51 19 2 408 993 Carbon front add-on section F32/F36 1.00 51 19 2 348 911 Side skirt film F32/F33/F36 0.75 51 62 2 334 545 Carbon rear spoiler F32 0.75 51 62 2 407 543 Carbon rear spoiler F36 0.75 51 19 2 354 500 Matt black rear spoiler F32 0.75 51 19 2 361 679 Matt black left side skirt add-on section F32/F33/F36 0.50 51 19 2 361 680 Matt black right side skirt add-on section F32/F33/F36 0.50 © BMW AG, Munich 01 29 2 350 388 (V/Z)

Transcript of Original BMW Accessories. Installation Instructions....Installation information - All...

Page 1: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

Original BMW Accessories.Installation Instructions.

M Performance Aerodynamics Package Retrofit Kit.BMW 4 Series Coupé (F32)BMW 4 Series Convertible (F33)BMW 4 Series Gran Coupé (F36)

Retrofit kit number

Installation timeInstallation time see table. This may vary depending on the condition of the vehicle and the equipment in it. The installation time shown does not include any time spent on programming/coding.The calculation of the total costs for the programming time must be factored into the calculation of retrofitting costs (no invoicing via warranty).

Important informationThese installation instructions are primarily designed for use within the BMW dealership organisation and by au-thorised BMW service companies.These installation instructions are intended for use by qualified specialist staff trained on BMW vehicles with the relevant expert knowledge.All work must be completed using the latest BMW repair manuals, wiring diagrams, servicing manuals and work instructions, in a rational order, using the prescribed tools (special tools) and observing current health and safety regulations.If you experience installation or function problems, restrict troubleshooting to approx. 0.5 hours for mechanical work and 1.0 hour for electrical work. To avoid unnecessary extra work and/or costs, send an inquiry straight away to the technical parts support team via the Aftersales Assistance Portal (ASAP).

Single-sided Twin-pipe

Twin-sided Single-pipe

Component designation Type Installa-tion time (h)

51 19 2 334 543 51 19 2 339 218 Rear diffuser, matt black F32/F33/F36 0.25

51 19 2 334 548 Carbon front add-on section F32/F36 1.00

51 19 2 408 993 Carbon front add-on section F32/F36 1.00

51 19 2 348 911 Side skirt film F32/F33/F36 0.75

51 62 2 334 545 Carbon rear spoiler F32 0.75

51 62 2 407 543 Carbon rear spoiler F36 0.75

51 19 2 354 500 Matt black rear spoiler F32 0.75

51 19 2 361 679 Matt black left side skirt add-on section F32/F33/F36 0.50

51 19 2 361 680 Matt black right side skirt add-on section F32/F33/F36 0.50

01 29 2 350 388 04/2016© BMW AG, Munich (V/Z) 104/2016© BMW AG, Munich 01 29 2 350 388 (V/Z)

Page 2: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

Quote the following information:- Chassis number,- Retrofit kit part number,- A detailed description of the problem,- Any work already carried out.Do not archive the hard copy of these installation instructions since daily updates are provided via ASAP.

PictogramsDenotes instructions that draw your attention to dangers.

Denotes instructions that draw your attention to special features.

Denotes the end of the instruction or other text.

Installation information- All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and free of wax,

silicon and grease. These surfaces must be treated with suitable BMW cleaner of BMW primer (see EPC for details), as set out in the appropriate product application instructions

- If you use adhesive tape, it must be applied using a contact pressure of between 10 N/cm2 and 50 N/cm2

- Take care not to damage the parts when opening the packaging- Check that all the parts fit accurately on the car before fitting them- All affected components and their bonding surfaces must be at room temperature for installation. The ideal rel-

ative humidity is 50%. Different values will change the specified times- After completing the gluing And installation work, the car must remain stationary at room temperature for at least

12 hours- If adhesives are used the car may be driven after 24 hours, and may be taken through a car wash after 48 hours.

The car must not be driven above a speed of vmax < 100 km/h for 24-48 hours

- The installed parts may become loose and fly off the car if you fail to wait for the full reaction time of the primer/adhesive. Danger of accidents!

- Some of the installation steps are shown only on one side of the car. Proceed in the same way on the other side of the car.

- All pictures show LHD cars; proceed accordingly on RHD cars

If an M Performance rear spoiler is to be installed, any rear spoiler already in place must be removed / dismantled as per ISTA.

Painting instructionsCheck that all the parts fit accurately on the car before painting them. Primed parts must be pre-treated accordingly before painting. To ensure correct painting, the EBA must be provided to the painter.The BMW painting instructions must be observed (see ISTA No. 99 00 ...).

!

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 2

Page 3: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

Ordering instructionsThe material such as liquid adhesive, cleaner and activators are assigned to the relevant products in the EPC (see EPC for instructions and part numbers). If the EPC does not explicitly specify the materials, always use cleaner, adhesive and activator from the BMW product range.When the carbon front add-on section is installed on cars of a light colour, a black paint pen is also required.

Recommended special toolsNone

Information to be provided to the customerOnce the carbon front add-on section has been installed, the ramp angle and floor clearance are reduced.

The carbon front add-on section may only be installed in conjunction with the rear spoiler (for part number and instructions, see EPC).

The carbon front add-on section reduces the car's floor clearance and reduces the overhang angle at the front. The carbon front add-on section must be checked at regular intervals for damage caused by collisions

and, in the event of any such damage, replaced by trained specialist personnel.

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 3

Page 4: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

Table of contents

Section Page

© BMW AG, Munich 401 29 2 350 388 04/2016 (V/Z)

1 Carbon front add-on section parts list only for part number 51 19 2 334 548 (F32/F36) . . . . . . . . . . . . . . . 5

2 Carbon front add-on section parts list only for part number 51 19 2 408 993 (F32/F36) . . . . . . . . . . . . . . . 6

3 Matt black side skirt add-on section parts list (F32/F33/F36) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4 Carbon rear spoiler parts list (F32) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

5 Carbon rear spoiler parts list (F36) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

6 Matt black rear spoiler parts list (F32) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

7 Preparatory work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

8 Fitting the carbon front add-on section for part number 51 19 2 334 548 (F32/F36) . . . . . . . . . . . . . . . . . . 13

9 Fitting the carbon front add-on section for part number 51 19 2 408 993 (F32/F36) . . . . . . . . . . . . . . . . . . 17

10 Fitting the side skirt films (F32/F33/F36). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

11 Fitting the matt black side skirt add-on section (F32/F33/F36) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

12 Fitting the carbon rear spoiler (F32) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

13 Fitting the carbon rear spoiler (F36) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

14 Fitting the matt black rear spoiler (F32) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

15 Fitting the matt black rear diffuser (F32/F33/F36). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

16 Concluding work and coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Page 5: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

1. Carbon front add-on section parts list only for part number 51 19 2 334 548 (F32/F36)

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 5

Legend

AA Carbon front add-on sectionAB C-clip (2 x)AC Installation plate incl. C-clip (2 x)AD Hexagon screw incl. washer (6 x)AE Installation plateAF Oval-headed screw incl. washer (2 x)AG Cover cap (2 x)AH Liquid adhesive (not included in kit, see EPC for details)

ADACAB

AA

AE AF

AG AH

F32 0063 V

Page 6: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

2. Carbon front add-on section parts list only for part number 51 19 2 408 993 (F32/F36)

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 6

Legend

BA Carbon front add-on sectionBB C-clip (4 x)BC Installation plate incl. C-clip (4 x)BD Oval-headed screw incl. washer M5 (4 x)BE Installation plateBF Oval-headed screw incl. washer M6 (2 x)BG Liquid adhesive (not included in kit, see EPC for details)

BDBCBB

BA

BE

BGBF

F32 0064 V

Page 7: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

3. Matt black side skirt add-on section parts list (F32/F33/F36)

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 7

Legend

CA Matt black right side skirt add-on sectionCB Matt black left side skirt add-on sectionCC Liquid adhesive (not included in kit, see EPC for details)CD Expanding rivet (15 x per side)

CA

CB

CDCC

F82 0168 V

Page 8: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

4. Carbon rear spoiler parts list (F32)

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 8

Legend

DA Rear spoilerDB Liquid adhesive (not included in kit, see EPC for details)

DA

DB

F32 0065 V

Page 9: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

5. Carbon rear spoiler parts list (F36)

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 9

Legend

EA Rear spoilerEB Liquid adhesive (not included in kit, see EPC for details)

EA

EB

F36 0004 V

Page 10: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

6. Matt black rear spoiler parts list (F32)

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 10

Legend

FA Rear spoilerFB Liquid adhesive (not included in kit, see EPC for details)

FA

FB

F32 0066 V

Page 11: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

7. Matt black rear diffuser (F32/F33/F36)

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 11

Legend

GA Diffuser insert (illustration shows double-sided and single-pipe exhaust system version) GB Expanded grille (2 x)GC Clamp (8 x)GD Masking tape

GDGCGB

GA

F32 0067 V

Page 12: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

8. Preparatory work

The following components must be removed first of all ISTA No.Lower rear bumper trim (keep the screws and rivets, they will be required again for later installation)

51 12 ...

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 12

Page 13: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

9. Fitting the carbon front add-on section for part number 51 19 2 334 548 (F32/F36)

Remove the outer screws (1) and the expanding rivets (2). The screws (1) and expanding rivets (2) are no longer required.Loosen the inner screws (3), but do not remove them.

Only for cars of a light colourFor cars of a light colour, the gap (4) must be blackened.

Place carbon front add-on section AA on the front apron and align. Using a suitable tool, draw a mark (5) on the front apron to demarcate the area to be blackened.Remove carbon front add-on section AA.

Using a black paint pen, draw a line around 2-3 mm thick (8) on the front apron (6) along the air inlet cover (2) up to the mark (9).

For all carsThe car surface (10) must be completely dry, clean and free from wax and grease.

Clean car surface (10) with a suitable cleaner.

3

1

2

F32 0009 V

AA54

F32 0068 V

97

8

6 F32 0069 V

10

F32 0070 V

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 13

Page 14: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

9. Fitting the carbon front add-on section for part number 51 19 2 334 548 (F32/F36)

The surface (11) must be completely dry and free from wax or grease.

Clean the surface (11) of carbon front add-on section AA using a suitable cleaner.Bend back the ends of the adhesive backing film just enough to form small tabs (12).

Apply liquid adhesive AH approx. 30 mm from the edge (13) and along the edge (13) on the inside of carbon front add-on section AA as shown.

The bonding surfaces must be completely clean, dry and free from wax or grease. Ensure that all tabs (12)

on the adhesive backing film are visible.Place carbon front add-on section AA on the car's front apron and align.Gradually remove the adhesive backing films in sequence using the tabs (12) to assist you and firmly and repeat-edly press carbon front add-on section AA into position.Remove any excess liquid adhesive immediately.

Place C-clip AB on the plastic plate (14) above the front apron (6) and position it over the hole (15) in the front apron (6).Position installation plate incl. C-clip AC over the drill hole (16) for carbon front add-on section AA on the front apron (6).

AA

11

12

1212

F32 0071 V

AA AH13

F32 0072 V

AA

12

F32 0073 V

AA6

ACAB

14

15 16

F32 0074 V

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 14

Page 15: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

9. Fitting the carbon front add-on section for part number 51 19 2 334 548 (F32/F36)

Screw in screws (17) through the drill hole (18) of carbon front add-on section AA and tighten them.Screw in screw (19) into C-clip AB and tighten it.Screw in screw (20) into the installation plate incl. C-clip AC and tighten it.Place cover cap AG on the drill hole (18).

When drilling down to the drilling depth, take care not to damage any parts/the metal support under-

neath.Drill holes (21) from carbon front add-on section AA through the front apron using a 6 mm drill bit.

Pull the front apron (6) slightly downwards and slide in-stallation plate AE into the depression (22). Align the drill holes (23) on installation plate AE over the previously-drilled holes in the front apron.

Screw in oval-headed screws AF through the drill holes (21) on front splitter AA into the installation plate (con-cealed).Tighten the screws (3).

ABAC

AG17 19

AA

18

20

F32 0075 V

AA

Ø 6 mm

21

F32 0076 V

6AE

22 23

F32 0077 V

AA3

AF 22

F32 0078 V

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 15

Page 16: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

9. Fitting the carbon front add-on section for part number 51 19 2 334 548 (F32/F36)

Secure carbon front add-on section AA using a suitable adhesive strip (24) as shown.

Do not remove the adhesive strips (24) for around 24 hours and do not move the car.

Note the painting instructions on page 2.

AA

24

F32 0079 V

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 16

Page 17: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

10. Fitting the carbon front add-on section for part number 51 19 2 408 993 (F32/F36)

Remove the outer screws (1) and the expanding rivets (2). The screws (1) and expanding rivets (2) are no longer required.Unscrew the inner screws (3) and keep them safe.

Only for cars of a light colourFor cars of a light colour, the gap (4) must be black-ened.

Place carbon front add-on section BA on the front apron and align. Using a suitable tool, draw a mark (5) on the front apron to demarcate the area to be blackened.Remove carbon front add-on section BA.

Using a black paint pen, draw a line around 2-3 mm thick (8) on the front apron (6) along the air inlet cover (2) up to the mark (9).

For all carsThe car surface (10) must be completely dry, clean and free from wax and grease.

Clean car surface (10) with a suitable cleaner.

3

1

2

F32 0009 V

BA54

F32 0080 V

97

8

6 F32 0081 V

10

F32 0082 V

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 17

Page 18: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

The surfaces (11) must be completely dry and free from wax or grease.

Clean the surfaces (11) of carbon front add-on section BA using a suitable cleaner. Bend back the ends of the adhesive backing film just enough to form small tabs (12).

Apply liquid adhesive BG approx. 30 mm from the edge (13) and along the edge (13) on the inside of carbon front add-on section BA as shown.

The bonding surfaces must be completely clean, dry and free from wax or grease. Ensure that all tabs (12)

on the adhesive backing film are visible.Place carbon front add-on section BA on the car's front apron and align.Gradually remove the adhesive backing films in sequence using the tabs (12) to assist you and firmly and repeat-edly press carbon front add-on section BA into position.Remove any excess liquid adhesive immediately.

Position installation plate incl. C-clip BC over the drill holes (14) for carbon front add-on section BA on the front apron (6).

BA

11

1212

12

F32 0083 V

BA

BG13

F32 0084 V

BA

12

F32 0085 V

6

BA

BC

14

F32 0086 V

10. Fitting the carbon front add-on section for part number 51 19 2 408 993 (F32/F36)

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 18

Page 19: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

10. Fitting the carbon front add-on section for part number 51 19 2 408 993 (F32/F36)

Screw in screw (15) through the drill hole (16) of front splitter BA and tighten them.Screw in screws (17) into the installation plate incl. C-clip BC and tighten them.

When drilling down to the drilling depth, take care not to damage any parts / the metal support under-

neath.Drill holes (18) from carbon front add-on section BA through the front apron using a 6 mm drill bit.

Pull the front apron (6) slightly downwards and slide in-stallation plate BE in. Align the drill holes (19) on installa-tion plate BE over the holes in the front apron (6) you drilled previously.

Screw in oval-headed screws BF through the drill holes (18) on carbon front add-on section BA into the installa-tion plate (concealed).Insert and tighten the existing screws (3).

BC

BA

16

15

17

F32 0087 V

BA

Ø 6 mm

18

F32 0088 V

6

BA

BE 19

F32 0089 V

BA3

BF18

F32 0090 V

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 19

Page 20: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

10. Fitting the carbon front add-on section for part number 51 19 2 408 993 (F32/F36)

Secure carbon front add-on section BA using a suitable adhesive strip (20) as shown.

Do not remove the adhesive strips (20) for around 24 hours and do not move the car.

Note the painting instructions on page 2.

BA

20

F32 0091 V

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 20

Page 21: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

11. Fitting the side skirt films (F32/F33/F36)

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 21

Install the side sill films in accordance with the installation instructions bearing part number

01 29 2 298 023.EBA-Nr. 01 29 2 298 023

F32 0022 V

Page 22: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

12. Fitting the matt black side skirt add-on section (F32/F33/F36)

The bonding surfaces must be completely dry, clean and free from wax or grease.

Clean the surface (1) of the car with a suitable cleaner.

The bonding surfaces must be completely dry, clean and free from wax or grease.

Clean the surface (2) of matt black side skirt add-on sec-tion CA with a suitable cleaner.Apply liquid adhesive CC as shown to matt black side skirt add-on section CA.

Ensure that all tabs on the adhesive backing film are visible.

Position matt black side skirt add-on section CA so that the edge (3) of matt black side skirt add-on section CA lies behind the edge (4) of the car.

Remove any excess liquid adhesive immediately.

Carefully remove the adhesive strip (5) from front to back and firmly press on matt black side skirt add-on section CA.Carefully remove the adhesive strip (6) from the outside inwards and firmly press on matt black side skirt add-on section CA.

When drilling down to the drill depth, take care not to damage parts underneath.

Using a 6 mm drill bit, transfer the 15 holes (7) from matt black side skirt add-on section CA to the side skirt.

1

F82 0024 V

CA

CC

2

CC

CA

4

3

F82 0173 V

7

Ø 6 mm

5

6CA

F82 0174 V

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 22

Page 23: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

12. Fitting the matt black side skirt add-on section (F32/F33/F36)

Secure matt black side skirt add-on section CA using 15 blind rivets CD.

Secure the rear part of matt black side skirt add-on section CA as shown using a suitable adhesive strip (8).

Note the painting instructions on page 2.

CD

CA

F82 0175 V

8

CA

F82 0176 V

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 23

Page 24: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

13. Fitting the carbon rear spoiler (F32)

The car surface (1) must be completely dry, clean and free from wax and grease.

Clean car surface (1) with a suitable cleaner.

Place the rear spoiler DA on the boot lid, centre it and mark the position (2) at the left and right using a suitable tool.

For clarity, only one side of rear spoiler DA is shown.

Sand and clean the side surface (3) on the underside of the rear spoiler DA using suitable tools. Then apply liquid adhesive DB in a bead with a diameter of 3 mm to the edge surface (3).

Centre the rear spoiler DA using the two marks (2), place it on the edge (4) of the boot lid and press it into place.

Remove any excess liquid adhesive immediately.

1

F32 0001 V

2 2

xx

DA

F32 0061 V

3DA

DB

F32 0059 V

2

24

DA

DA

F32 0060 V

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 24

Page 25: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

13. Fitting the carbon rear spoiler (F32)

Secure rear spoiler A using suitable adhesive tape (5) at several points for at least 24 hours.

Note the painting instructions on page 2.

Positions (1), (2) and (3) are provided for the tail-gate's tension spring.

Move the tailgate's tension spring to position (3).

After repositioning the tension springs, check that the tailgate is able to open properly and adjust the

position of the tension springs accordingly if necessary.

5

DA

F32 0062 V

3

2

1

F32 0026 V

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 25

Page 26: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

14. Fitting the carbon rear spoiler (F36)

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 26

The car surface (1) must be completely dry, clean and free from wax and grease.

Clean car surface (1) with a suitable cleaner.

Sand and clean the areas (2) of the rear spoilerEA using suitable materials and then apply liquid adhesive EB to the areas (2).

Place rear spoiler EA on the edge of the boot lid and adjust it so that it is in the centre.

Remove any excess liquid adhesive immediately.

Secure rear spoiler EA using suitable adhesive tape (3) at several points for at least 24 hours.

Note the painting instructions on page 2.

1

F30 0183 V

2

2

EA

EB

F36 0005 V

x xEA

F36 0006 V

333

EA

F36 0007 V

Page 27: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

15. Fitting the matt black rear spoiler (F32)

The car surface (1) must be completely dry, clean and free from wax and grease.

Clean car surface (1) with a suitable cleaner.

The surfaces (2) must be completely dry and free from wax or grease.

Sand and clean the surfaces (2) of rear spoiler FA with suitable materials.Apply liquid adhesive FB liberally (length: approx. 8 cm) to the middle of the surfaces (2).Then pull back the ends of the adhesive backing films on rear spoiler FA far enough so that small tabs (2) form.

Make sure that all tabs on the adhesive backing film and the liner projections are visible after contact has

been made.Place rear spoiler FA on the boot lid and centre it between the edges (4).Remove any excess liquid adhesive immediately.

Align rear spoiler FA so the surfaces (5) and (6) transition into one another.

1

F32 0028 V

FA

FBFB

3

32 2

F32 0092 V

FA

4

F32 0093 V

FA

56

F32 0094 V

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 27

Page 28: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

15. Fitting the matt black rear spoiler (F32)

Pull off the upper adhesive backing films (7) of rear spoiler FA starting from the middle.

Pull off the side adhesive backing films (8) of rear spoiler FA.

Pull off the lower adhesive backing films (9) of rear spoiler FA starting from the middle.Then pull the lower adhesive backing films (10) of rear spoiler FA off outwards.Press rear spoiler FA firmly and repeatedly onto the boot lid.

Note the painting instructions on page 2.

Positions (1), (2) and (3) are provided for the tail-gate's tension spring.

Move the tailgate's tension spring to position (3).

After repositioning the tension springs, check that the tailgate is able to open properly and adjust the

position of the tension springs accordingly if necessary.

7

FA

F32 0095 V

8

FA

F32 0096 V

9

FA

1010

F32 0097 V

3

2

1

F32 0026 V

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 28

Page 29: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

16. Fitting the matt black rear diffuser (F32/F33/F36)

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 29

Remove the bar (1) of the diffuser insert GA using a suitable knife and deburr the cut edges of the diffuser insert GA.

Diffuser insert GA can be partially painted in the car colour if the customer so wishes. See painting

instructions.Before painting, mask the marked area (2) of diffuser insert GA using masking tape and masking tape GD using the painting spaces (3) provided.Do not paint the masked areas.

Only for cars of a light colourBlacken the area (4) of the car at the rear right using suitable means.

For all carsPlace extended grille GB on the four tabs (5) of diffuserinsert GA.

Start with the clamps at the bottom.Secure extended grille GB with clamps GC.

Extended grille GB must be curved outwards.Bend the edge (6) of extended grille GB inwards into

the diffuser.Then push extended grille GB slightly outwards along the line (7) so that extended grille GB curves outwards.Install the extended grille GB on the right-hand side in the same way.Fit diffuser insert GA as described in ISTA No. 51 12 ....

3

GA

GD

21 1

F32 0098 V

4

F32 0099 V

5

5

GA

GB

GC

F32 0100 V

6

GA

GB7

F32 0101 V

Page 30: Original BMW Accessories. Installation Instructions....Installation information - All contact/bonding surfaces on the components being installed must be absolutely dry, clean, and

17. Concluding work and coding

04/201601 29 2 350 388© BMW AG, Munich (V/Z) 30

The retrofit system does not require coding.- Conduct a brief test- Conduct a function testRe-assemble the car