Organophosphorus Reagents

7/29/2019 Organophosphorus Reagents

1/274


2/274

Contents

List of contributors xi

1. Organophosphorus chemistry 1

Patrick J. Murphy

1. Introduction 1

2. Nomenclature 1

3. Practical methods 2

References 12

2. The synthesis and applicationsof phosphines 15

Matthew L. Clarke and Jonathan M. J. Williams

1. Introduction 15

2. Preparation of tertiary phosphines 18

3. Preparation and reactivity of primary and secondary phosphines 26

4. Polydentate phosphines and macrocycles 32

5. Chiral phosphines 35

6. Synthesis and applications of phosphines in environmentally

benign catalysis42

7. Applications of phosphines in catalysis 45

References 48

3. Applications of phosphorus (III) and (V)compounds as reagents in synthesis 51

R. Alan Aitken and Nazira Karodia

1. Introduction 51

2. Deoxygenation and desulfurization reactions 51

3. Halogenation reactions 63

4. Dehydrative coupling and cyclization reactions 74

5. Sulfurization reactions 81

6. Miscellaneous reactions 87

References 95


3/274

Contents

4. The Wittig and related reactions 99

Andrew D. Abell and Michael K. Edmonds

1. Introduction 99

2. Standard reagents and procedures 1043. Modifications to the standard reagents and procedures 111

4. Role in synthesis 116

References 126

5. Applications of the Wittig reaction inthe synthesis of heterocyclic andcarbocyclic compounds 129

Rainer Schobert

1. Introduction 129

2. Ring-closure variants utilizing highly reactive

-carbonyl-ylides 131

3. Ring-closure variants employing less reactive -carbonyl ylides or

non-classical Wittig olefinations of esters and amides 137References 148

6. Preparation and reactions ofiminophosphoranes and their syntheticapplications in the aza-Wittig reaction 151

J. Mike Southern and Ian A. ONeil1. Introduction 151

2. Preparation of iminophosphoranes 152

3. Removal of triphenylphosphine oxide 154

References 168

7. Phospho-transfer processes leading to[P

C] bond formation 171

Matthew D. Fletcher

1. Introduction 171

2. The MichaelisArbuzov reaction 172

3. The MichaelisBecker reaction 185

4. The Perkow reaction 191

viii


4/274

Contents

5. The Abramov reaction 194

6. The Pudovik reaction 198

7. The KabachnikFields reaction 204

8. Conjugate additions of phosphorus(III) reagents 208

References 210

8. Low-coordinated phosphorus compounds 215

Sven Asmus, Uwe Bergstrer, Heinrich Heydt,Marion Schmitz and Manfred Regitz

1. Introduction 215

2. Phosphorus compounds having coordination number 1 2173. Phosphorus compounds having coordination number 2 223

References 233

9. Phosphorus methods innucleotide chemistry 237

David M. Williams and Vicki H. Harris1. Introduction 237

2. Outline of chemistry 237

3. Synthesis 241

4. Analysis and purification 264

Acknowledgements 271

References 271

Index 273

ix


5/274

1

Organophosphorus chemistryPAT R I C K J . M U R P H Y

1. IntroductionThe impact of organophosphorus chemistry on modern synthetic chemistry isdifficult to quantify, but one can safely assume that the study of this elementhas influenced all areas of chemical endeavour.1 Organophosphorus chemistry,as a discrete area of study, is the study of compounds containing a CP bondand this book is largely focused on this topic. However, other areas of interestincluding azaphosphorus, oxyphosphorus and metallophosphorus chemistry arediscussed either explicitly as topics or in an implicit manner within the chemistrydetailed in each chapter. The purpose of this introductory chapter is to covermany of the general aspects of organophosphorus chemistry and the chemicaltechniques required for their preparation, including practical methods commonlyencountered and some aspects of spectroscopy.

Many texts on organophosphorus chemistry have been published ranging fromin-depth studies of the subject as a whole1,2 to more general texts,3 which wouldserve as a general introduction to the field. Of the more comprehensive texts, thefour-volume2ad series entitled The Chemistry of Organophosphorus Compoundsedited by Hartley provides core material published before 1990 and representsan excellent starting point for those new to the field. A considerable amountof organophosphorus chemistry is published in the core literature, which canbe difficult to access, however, the periodical Organophosphorus Chemistry4

published annually by the Royal Society of Chemistry offers a yearly review ofthehighlightsandkeydevelopmentsinthefield.4 Several other periodicals, whichare no longer published are worthy of note5 and the two journals Phosphorus,

Sulfur and Silicon, and the Related Elements and Heteroatom Chemistry providea considerable quantity of useful information for the serious researcher.6

2. NomenclatureThe nomenclature of phosphorus-containing compounds is complicated to someextent by the overlap of inorganic and organic nomenclature, particularly withrespect to compounds containing the POH functionality. From the point ofview of this volume, the basic nomenclature used for trisubstituted phosphorus


6/274

P. J. Murphy

compounds is given in Scheme 1, and that for tetrasubstituted compounds isshown in Scheme 2.1

R

P

R

R

Phosphines; R = H, alkyl, aryl

R = HalRO

P

OR

R

Phosphonites;

R = H, alkyl, aryl

R

P

OR

R

Phosphinites;

R = H, alkyl, aryl

RO

P

OR

OR

Phosphites;

R = H, alkyl, aryl

Scheme 1 Nomenclature for trisubstituted phosphorus compounds.

O

P

R

R

R

R

P

R

R

R Phosphonium salts;

R = alkyl, aryl

Phosphine oxides; R = alkyl, aryl

Phosphoryl halides; R = Hal

+

R2C

P

R

R

R Alkyene phosphoranes (ylides);

R = alkyl, aryl

RN

P

R

R

R Azaphosphenes;

R = alkyl, aryl

O

P

OR

R

R Phosphinates;

R = alkyl, aryl

O

P

OR

R

OR Phosphonates;

R = alkyl, aryl

O

P

OR

OR

OR Phosphates;

R = alkyl, aryl

Scheme 2 Nomenclature for tetrasubstituted phosphorus compounds.

3. Practical methodsThe reader is referred to more general texts for further information on generalexperimental techniques.7 However, it is hoped that for those not experienced

2


7/274

1: Organophosphorus chemistry

with organic chemistry, enough information has been provided here to perform theexperiments. This chapter is intended to familiarize the reader with the equipmentand techniques, which are used in the protocols throughout the book.

3.1 SolventsAs with most synthetic organic chemistry, the availability of pure, and in manycases, dry and oxygen-free solvents is essential for both effecting synthetic trans-formations and for purification purposes. A wide range of organic solvents areemployed in organophosphorus chemistry, and many are available from suppliersin an anhydrous form, packaged under nitrogen in SureSeal bottles, which areusually suitable for use in the reactions we will cover. However, an alternativemethod is to purchase technical-grade solvents, which are then treated with chem-

ical drying agents to remove the moisture present and then distilled, either directlybefore use or onto a drying agent for storage, such as molecular sieves. A range ofmethods are available for drying solvents810 andthetypicalsolventsemployedinorganophosphorus chemistry and their method of distillation are detailed below.

3.1.1 Diethyl ether and tetrahydrofuran (THF)

These solvents can be dried efficiently by first drying over sodium wire and thendistilling directly before use, from sodium metal under an inert atmosphere inthe presence of a small amount of benzophenone. This combination producesa deep-blue/purple solution of sodium benzophenone ketyl if the solvent is dry,and the ketyl colour acts as an indicator, which, when it fades, indicates thatadditional sodium is needed. This is also an advantageous method as the ketylis an extremely efficient oxygen scavenger.8 It is important that peroxide-freediethyl ether and tetrahydrofuran (THF) are employed in the still, and it is alsoimportant to ensure that peroxides do not accumulate in stored samples of thesesolvents. A simple test for this is to mix a sample of the solvent (approximately1 mL) with glacial acetic acid (1 mL) containing KI crystals (100 mg). A yellowcolouration indicates the presence of a small quantity of peroxides, whilst a deepbrown colouration indicates a higher concentration. Peroxides can be removedin a number of ways,8,9 the most convenient being to wash repeatedly with anacidified FeSO4 solution (FeSO4 (60 g), concentrated H2SO4 (6 mL), and water(110 mL)), until a negative peroxide test is obtained. The solvent should thenbe washed with KMnO4 solution (0.5%), NaOH solution (5%), water, and thendried over CaCl

2for 24 h.

3.1.2 Benzene and toluene

These solvents are most conveniently dried by treatment with calcium hydridefollowed by distillation onto 4 molecular sieves.

3.1.3 Petroleum ether (petrol)

Petroleum ether can be dried by distillation onto activated 4 molecular sieves.

3


8/274

P. J. Murphy

3.1.4 Dichloromethane

Dichloromethane can be dried by treatment with calcium hydride in a continuousstill or can be stored by distillation onto 4 molecular sieves. Caution! Nevertreat chlorinated solvents with sodium or strong basesan explosion may occur.

3.1.5 Dimethylformamide (DMF)

Stir over calcium hydride or phosphorus pentoxide for 24 h, filter under an inertatmosphere and distil (56C at 20 mmHg) onto 3 molecular sieves. An altern-ative method is to dry over three batches of 3 molecular sieves (5% w/v,3 12 h).

3.1.6 Molecular sieves

The immediate use of dried, deoxygenated solvents is recommended, althoughnon-ethereal solvents can be stored over activated molecular sieves in thoroughlydried containers under N2/Ar. It is recommended that new molecular sieves bedried before use by heating them in a well-ventilated oven at 320C for 3 hfollowed by cooling them in an evacuated desiccator, which is filled with dryN2/Ar. Sieves may be reused if they are free from residual solvents.

3.1.7 Distillation set-up

If regular amounts of solvent are required, it is convenient to set up a solventdistillation apparatus, commonly referred to as a solvent still. A solvent stillenables a continuous supply of dry solvent to be available, which can be conveni-ently collected under an inert atmosphere. Common stills are those for dryingdiethyl ether, THF, and dichloromethane. The still shown in Figure 1.1 has anadaptation for removing solvents from the still-head collection reservoir througha septum cap by syringe or, if larger quantities are required, a flask can be con-nected to the Quickfit adapter on the still-head. These two methods minimizethe exposure of the solvent to the atmosphere. When using a solvent still, thefollowing precautions should be observed:

1. The still should be situated in an efficient fume hood, and all tubing for inertgas and water supplies should be securely attached using copper wire or plasticcable ties.

2. The heating mantle should be of such a design that there is no risk of sparksigniting the solvent. This also applies to all electric cables and plugs. Themantle should also incorporate an electricity cut-out device to operate if thewater supply to the condenser fails.

3. It is imperative that the bottom flask containing the drying agent should notbe allowed to boil dry. This risk can be minimized if the flask is of greatercapacity than the collection reservoir and is regularly topped up with solvent.

4. During cooling, an adequate flow of inert gas should be maintained.

4


9/274


Inert gas supply

Water

Water

Septum

Two-way tap

To receiving flask

Round-bottomed flask

Three-way tap

Overflow device

Stoppered side-arm

with retaining clip

(to refill still)

Condenser

Two-way tap

Fig. 1.1 General set-up for a solvent still (reproduced with permission from Ref. 13).

5. Caution! The use of a semi-permanent still for ethereal solvents can leadto a build-up of peroxides. The solvent should be checked for peroxides at

frequent intervals, and if these are detected, the still should be dismantled andthe drying agent and peroxides carefully destroyed. Also, when renewing thestill, fresh batches of the solvent and drying agent should be used.

3.2 Working under an inert atmosphere

Many preparations require the use of an inert atmosphere and are thus carried out

under an atmosphere of anhydrous nitrogen or argon. Argon has the advantageof being heavier than air and, therefore, provides a more effective barrier againstthe outside atmosphere, but nitrogen is more commonly used owing to its lowercost. The best method for ensuring that reactions are purged free of oxygen is toemploy a purpose-built double manifold of the type shown in Figure 1.2. Thisapparatus provides the inert gas and a vacuum source via two-way stopcocksand allows several inert atmosphere experiments to be run simultaneously. It canalso be fitted with a Quickfit adapter fitted with a septum, which can be used for

5


10/274

P. J. Murphy

Connector

Two-way stopcock

To apparatus

Inert gas supply

To vacuum

Paraffin oil

Fig. 1.2 Double manifold apparatus (reproduced with permission from Ref. 13).

purging syringes with inert gas. The supply of inert gas to the manifold should becontrolled in two stages using a cylinder regulator and then a needle valve, andthe apparatus should also be equipped with a bubbler to control the release of gas.

Further examples of apparatus designed for specific applications appear inthe recommended experimental texts for organic synthesis.7

3.3 Reaction apparatus

A variety of experimental set-ups will be employed throughout this book. In caseswhere cooling of a process is required, an arrangement of glassware similar tothat shown in Figure 1.3 will be suitable. This consists of a three-necked flaskequipped with a magnetic stirring bar, a septum, a low temperature thermometer,

and an inlet for inert gas and vacuum. Liquid reagents and solvents can be addedvia syringe through the septum and, provided that an adequate flow of inert gasis maintained, the septum can be removed to allow the addition of solids.

If heating of the reaction is required, the flask should be equipped with a refluxcondenser and an efficient heating apparatus. Two options are generally availablefor heating a reaction, first, an isomantle which offers direct heating to the flaskand can be equipped with a stirring mechanism. Alternatively, an oil-bath is morefrequently used as illustrated (Figure 1.4) as this option offers more controlled

heating. It is recommended that only fresh paraffin or silicone oil is used in thebath and that a temperature regulating device is fitted to the bath in conjunctionwith a water cut-out mechanism.

3.4 Standardization of organolithium reagents

In many of the preparations detailed in this book, the use ofn-BuLi is required.It is recommended that for any purchased solution, this reagent is standardizedbefore use as there is generally a considerable difference between the expected

6


11/274


Balloon

Tubing

To vacuum

Fasten with anelastic bandThermometer

Stirring bar

Graduated syringe

Needle

Septum

Nitrogen/

argon entry

Three-way

stopcock

Dry-ice Dewar or

insulated cold bath

Fig. 1.3 Apparatus for performing a reaction at low temperature (reproduced with permis-

sion from Ref. 13).

Condenser

Water out

Clamp

Clamp

Magneticstirrer bars

Waterin

Thermometer

Heating bath(oil, etc.)

Magneticstirrer/ hotplate

Fig. 1.4 Apparatus for performing a reaction under reflux.

7


12/274

P. J. Murphy

concentration and the actual one, as the reagent may have deteriorated over time.Many methods are available for the standardization, but the most convenientare those which rely on the formation of coloured dianions.1113 A procedure(Protocol 1) using 1-pyreneacetic acid is one of the most convenient in view of

thedistinctiveredend-pointobtainedandthefactthatthereagentcanberecoveredeasily from titration mixtures and then reused.12,13 The procedure described canbe used for the standardization of butyl-lithium and allows an estimation of thereagent concentration within approximately 0.1 M; it is recommended that theprotocol be performed in duplicate.

Protocol 1.

Titration ofn

-butyl-lithium using 1-pyreneacetic acid

12,13

Caution! Carry out all procedures in a well-ventilated hood, and wear disposable

vinyl or latex gloves and chemical-resistant safety goggles.

Equipment (see Figure 1.5)

A pre-dried, two-necked, round-bottomed flask

(50 mL) incorporating side-arm tap adapter (for

inert gas inlet), with magnetic stirring bar,

septum and gas outlet

Dry, gas-tight syringes [1 mL, with 0.01 mL

graduations (preferably fitted with a screwdriver

plunger), and 10 mL]

Inert gas supply

Materials

Butyllithium solution to be standardized pyrophoric

1-Pyreneacetic acid (FW 260.3), pre-dried to constant weight in vacuo, (100200 mg)

Anhydrous THF 10 mL flammable, irritant

Graduated syringe

Two-way stopcock

Stirring bar

Septum

Vent needle to bubbler

To vacuum

inert atmosphere

Fig. 1.5 Apparatus for standardization of n-BuLi (reproduced with permission from

Ref. 13).

8


13/274


Method

1. Flush the round-bottomed flask and accessories with dry, oxygen-free N2/Ar.

Flame dry the flask and allow it to cool in a stream of inert gas. Maintain an

inert atmosphere during the remaining steps.

2. Weigh out the 1-pyreneacetic acid accurately, using an analytical balance,

and transfer to the round-bottomed flask. Add the THF and stir the mixture

until a homogeneous solution is obtained.

3. Charge the 1 mL syringe with the organolithium reagent, and then insert

the needle through the septum. Add the organometallic reagent slowly and

dropwise (over a period of 34 min; slow addition is essential to minimize

reaction between THF and BuLi). The end-point is when the red colour of the

dianion just persists.

4. The molarity of the butyl-lithium can now be calculated from a consideration

of the number of moles of 1-pyreneacetic acid utilized and the volume of BuLi

required to obtain a permanent end-point (molarity (M)= mols/vol).

3.5 Cooling baths

Manyreactionsarecarriedoutinthetemperaturerange0to 100Candarangeofcooling systems are available for achieving these temperatures. Table 1.1 is a listof common slush bath compositions, however, many others are available.9,14,15

The temperature of the reaction mixture should be monitored by means of aninternal thermometer (or a temperature probe), as shown in Figure 1.3, sincethe internal temperature may differ significantly from that of the cooling bath

Table 1.1 Common slush bath compositions

Solvent/additive Temperature (C)

Ice 0

Ice/salt (3 : 1) 8

Carbon tetrachloride/CO2 23Ice/CaCl2 6H2O (4 : 5) 40

Acetonitrile/CO2 42

Chloroform/CO2 61

Ethanol/CO2 72

Acetone/CO2 78

Hexane/liquid N2 94

Ethanol/liquid N2 116

Liquid N2 196

9


14/274

P. J. Murphy

Motor

Vacuum

Heating controlTemperature

gauge

OvenSample

Fig. 1.6 A Kugelrohr bulb-to-bulb distillation apparatus.

medium, particularlyduringtheaddition of reagents whichproduce an exothermicreaction.

3.6 Vacuum distillation

Starting materials, reaction products and solvents often need to be distilled inorder to enhance purity. For small-scale distillations, a Kugelrohr bulb-to-bulb

distillation apparatus is convenient (Figure 1.6). The sample is placed in the endbulb, the system placed under vacuum if required and the oven temperature israised. The sample distils into the next bulb (which is outside of the heatingcompartment) and collected. The distillate can then be redistilled into the nextbulb, if required. If the sample has a relatively low boiling point under the pressureemployed, it is common practice to cool the receptor bulb with ice, dry ice, oreven liquid nitrogen (absorbed onto cotton wool).

A short-path distillation procedure may be used in situations where a simple

distillation is required, as purification from non-volatile components/fractionaldistillation with a Kugelrohr apparatus is difficult. A water-jacketed, semi-microdistillation apparatus is illustrated in Figure 1.7. Heating can either be achievedwith the aid of an oil-bath, an isomantle, or a flame (Caution! ensure that there areno flammable solvents nearby). For larger scale distillations, a round-bottomedflask should be attached to a distillation column, a still-head, and condenser. Thecolumn used in the distillation is variable, and may be either a Vigreux columnor a column packed with glass helices.

3.7 Spectroscopic techniques

A variety of spectroscopic techniques are available to the practising organicchemist, and many sources of information are available with excellent cover-age of the essential methods and analysis of spectroscopic data.16 It is widelyaccepted that nuclear magnetic resonance (NMR) spectroscopy has become themost essential tool for the organic chemist and the reader is assumed to have

10


15/274


Quick fit thermometer

Short path destilation apparatus

To vaccum pump

Magnetic stirrer

bar

Fig. 1.7 A semi-micro distillation apparatus.

a basic understanding of the principals of the technique and the analysis of thespectra obtained from them.The stable isotope of phosphorus 31P has a spin of I= 1/2 and is, thus,

NMR active. A considerable amount has been written17 on 31P NMR and thereader is referred to these texts for more specialized information. In the spe-cific examples presented in this volume, 31P chemical shifts will be referredto as and when they are required. In general, the magnitudes of the chemicalshifts observed are dependent on both the electronegativity of the substituients

directly attached to the phosphorus and the amount of back donation of elec-trons by -bonding. Thus, increasing the electronegativity of the substituientgroups decreases the electron density at the phosphorus atom and leads to a shiftto higher frequency (deshielding). Phosphorus compounds resonate over a verywide range (circa+600 to450 ppm relative to an 85% orthophosphoric acidstandard), however, direct correlation between chemical shift and structure arenot as predictable as those in 1H and 13C NMR spectroscopy. A small selectionof chemical shifts for organophosphorus compounds is given in Table 1.2 for

comparison and reference purposes.Infrared spectroscopy can also be of diagnostic use for the identification of

organophosphorus compounds and comprehensive data is available from sev-eral sources.18 Diagnostic absorptions include the PH stretch, which typicallyoccurs in the region 24602450 cm1, the P==O stretch at 13201200 cm1 andthe P==N at 14401120 cm1. Other useful absorptions include the PO(C)stretch at 870730 cm1 and the POP stretch at 800650 cm1 found inphosphate esters.

11


16/274

P. J. Murphy

Table 1.2 Chemical shifts for some

organophosphorus compounds

Structure Chemical shift

PMe3 62PPh3 6

PCl3 +219

PCl5 80

PBr3 +227

MePCl2 +191

PhPCl2 +162

Ph2PCl +81

Ph2PH 41

P(OEt)3 +137

P(OPh)3 +127

(EtO)2PCl +165

Et3PO +48

Ph3PO +29

(MeO)3PO +2

(Me2N)3PO +24

(MeO)2POCl +8

(MeO)2POH +10

Ph3P=CH2 +20

Ph3PCH+

3 Br

+23H3PO4 0

H3PO2 +13

Me2PO2H +49

References1. For a major review of the general chemistry of phosphorus and its impact on the

20th century see: Corbridge, D. E. C., Phosphorus 2000; Elsevier: Amsterdam;2000.

2. (a) Hartley, F. R. ed. The Chemistry of Organophosphorus Compounds. Primary,Secondary and Tertiary Phosphines, Polyphosphines and Heterocyclic Organo-

phophorus(III) Compounds; John Wiley & Sons: Chichester; 1990, Vol. 1.(b) Hartley, F. R. ed. The Chemistry of Organophosphorus Compounds. PhosphineOxides, Sulphides, Selenides and Tellurides; John Wiley & Sons: Chichester; 1992,Vol. 2. (c) Hartley, F. R. ed. The Chemistry of Organophosphorus Compounds. Phos-

phonium Salts, Ylides and Phosphoranes; John Wiley & Sons: Chichester;1994

,Vol. 3. (d) Hartley, F. R. ed. The Chemistry of Organophosphorus Compounds. Ter-and Quinque-Valent Phosphorus Acids and Their Derivatives; John Wiley & Sons:Chichester; 1996, Vol. 4.

3. (a) Quin, L. D. Guide to Organophosphorus Chemistry; Wiley-Interscience:NewYork; 2000. (b) Engel, R. Synthesis of PhosphorusCarbon Bonds; CRCPress: Boca Raton, FL; 1988. (c) Goldwhite, H. Introduction to Phosphorus Chem-istry; Cambridge University Press: Cambridge, UK; 1981. (d) Cadogan, J. I. G.

12


17/274


Organophosphorus Reagents in Organic Synthesis; Academic Press: NewYork; 1979.(e) Emsley, J.; Hall, D. The Chemistry of Phosphorus: Environmental, Organic,Inorganic, Biochemical and Spectroscopic Aspect; Harper and Row Publishers: NewYork; 1976. (f) Walker, B. J. Organophosphorus Chemistry; Penguin Books: England;1972.

4. Organophosphorus Chemistry; specialist periodical reports. The Chemical Society(London); 19702003, Vols. 133.

5. (a) Topics in Phosphorus Chemistry; Interscience Publishers: New York; 19641983,Vols. 111. (b) Organe Phosphorus Compounds; Kosolapott, G. M.; Maier, L., Wiley-Interscience; New York, 19721976, Vols. 17. (c) Edmundson, R. S. ed. Dictionaryof Organophosphorus Compounds; Chapman & Hall: New York; 1988.

6. (a) Phosphorus, Sulfur and Silicon, and the Related Elements; Gordon and BreachPublishers: New York. (b) Heteroatom Chemistry; Wiley Publishers: New York.

7. (a) Harwood, L. M.; Moody, C. J.; Percy, J. M. Experimental Organic Chemistry:Preparative and Microscale; Blackwell Science (UK); 1998. (b) Leonard, J.; Lygo,B.; Procter, G. Advanced Practical Organic Chemistry; Chapman & Hall: New York;1995, 2nd edn. (c) Palleros, D. R. Experimental Organic Chemistry; John Wiley &Sons: Chichester; 2000. (d) Zubrik, J. W. The Organic Chem Lab Survival Manual. AStudents Guide to Techniques; John Wiley & Sons: Chichester; 1997. (e) Pavia, D. L.;Lampman, G. M.; Engel, R. G. Introduction to Organic Laboratory Techniques: ASmall-scale Approach; Sanders College Publishing Philadelphia; 1998. (f) Wilcox,C. F.; Wilcox, M. F. Experimental Organic Chemistry: A Small Scale Approach;

Prentice Hall: New York; 1994. (g) Furniss, B. S.; Hannaford, A. J.; Smith, P. W. G.;Tatchell, A. R., eds. Vogels Textbook of Practical Organic Chemistry; Longmans:London; 1989, 5th edn.

8. Armarego, W. L. F.; Chai, C. Purifaction of Laboratory Chemicals; Butterworth-Heinemann: Woburn, MA; 2003, 5th edn.

9. Gordon, A. J.; Ford, R. A. The Chemists Companion; John Wiley & Sons: New York;1972.

10. Gill, G. B.; Whiting, D. A. Aldrichimica Acta 1986, 19, 3141.11. Crompton, T. R. Chemical Analysis of Organometalic Compounds; Academic Press:

London; 1973.12. Kiljunen, H.; Haas, T. A. J. Org. Chem. 1991, 56, 69506952.13. Taylor, R. J. K.; Casy, G. Organocopper Reagents; Taylor, R. J. K., ed.; Oxford

University Press: New York; 1994, pp. 5256.14. Phillips, A. M.; Hulme, D. N. J. Chem. Ed. 1968, 54, 664.15. Rondeau, R. E. J. Chem. Eng. Data 1966, 11, 124.16. (a) Breitmaier, E. Structure Elucidation by NMR in Organic ChemistryA Practical

Guide; John Wiley & Sons: New York; 2002. (b) Field, L. D. Organic Structures

from Spectra; John Wiley & Sons: New York; 2002. (c) Silverstein, R. M.; Web-ster, F. X. Spectrometic Identification of Organic Compounds; John Wiley & Sons:New York; 2000. (d) Harwood, L. M.; Claridge, T. D. W. Introduction to OrganicSpectroscopy (Oxford Chemistry Primers); Oxford University Press: New York;1996. (e) Williams, D. H.; Fleming, I. Spectroscopic Methods in Organic Chemistry;McGraw-Hill Education, Europe; 1995, 5th edn.

17. (a)Tebby,J.C. CRC Handbook of Phosphorus-31 Nuclear Magnetic Resonance Data;CRC Press: Boca Raton, FL; 1991. (b) Quin, L. D.; Verkade, J. G. Phosphorus-31

13


18/274

P. J. Murphy

NMR Spectral Properties in Compound Characterisation and Structural Analysis;VCH: New York; 1994. (c) Verkade, J. G.; Quin, L. D. Phosphorus-31 NMRSpectroscopy in Stereochemical Analysis; VCH Publishers: Deerfield Beach, FL;1987. (d) Gorenstein, D. G. Phosphorus-31 NMR: Principles and Applications; Aca-demic Press: Orlando, FL; 1984. (e)NMR Spectra of Phosphorus Compounds, Topicsin Phosphorus Chemistry; Interscience Publishers: New York; 1967, Vol. 5.

18. (a) Thomas, L. C. Interpretation of the Infrared Spectra of Organophosphorus Com-pounds; Heyden: London; 1974. (b) Corbridge, D. E. C. In Topics in PhosphorusChemistry; Grayson, M.; Griffith, J. eds; Interscience: New York; 1969, Vol. 6,pp. 235365. (c) Corbridge, D. E. C. J. Appl. Chem. 1956, Vol. 6, 456465.

14


19/274


20/274


21/274


22/274


23/274


24/274


25/274


26/274


27/274


28/274


29/274


30/274


31/274


32/274


33/274


34/274


35/274


36/274


37/274


38/274


39/274


40/274


41/274


42/274


43/274


44/274


45/274


46/274


47/274


48/274


49/274


50/274


51/274


52/274


53/274


54/274


55/274


56/274


57/274


58/274


59/274


60/274


61/274


62/274


63/274


64/274


65/274


66/274


67/274


68/274


69/274


70/274


71/274


72/274


73/274


74/274


75/274


76/274


77/274


78/274


79/274


80/274


81/274


82/274


83/274


84/274


85/274


86/274


87/274


88/274


89/274


90/274


91/274


92/274


93/274


94/274


95/274


96/274


97/274


98/274


99/274


100/274


101/274


102/274


103/274


104/274


105/274


106/274


107/274


108/274


109/274


110/274


111/274


112/274


113/274


114/274


115/274


116/274


117/274


118/274


119/274


120/274


121/274


122/274


123/274


124/274


125/274


126/274


127/274


128/274


129/274


130/274


131/274


132/274


133/274


134/274


135/274


136/274


137/274


138/274


139/274


140/274


141/274


142/274


143/274


144/274


145/274


146/274


147/274


148/274


149/274


150/274


151/274


152/274


153/274


154/274


155/274


156/274


157/274


158/274


159/274


160/274


161/274


162/274


163/274


164/274


165/274


166/274


167/274


168/274


169/274


170/274


171/274


172/274


173/274


174/274


175/274


176/274


177/274


178/274


179/274


180/274


181/274


182/274


183/274


184/274


185/274


186/274


187/274


188/274


189/274


190/274


191/274


192/274


193/274


194/274


195/274


196/274


197/274


198/274


199/274


200/274


201/274


202/274


203/274


204/274


205/274


206/274


207/274


208/274


209/274


210/274


211/274


212/274


213/274


214/274


215/274


216/274


217/274


218/274


219/274


220/274


221/274


222/274


223/274


224/274


225/274


226/274


227/274


228/274


229/274


230/274


231/274


232/274


233/274


234/274


235/274


236/274


237/274


238/274


239/274


240/274


241/274


242/274


243/274


244/274


245/274


246/274


247/274


248/274


249/274


250/274


251/274


252/274


253/274


254/274


255/274


256/274


257/274


258/274


259/274


260/274


261/274


262/274


263/274


264/274


265/274


266/274


267/274


268/274


269/274


270/274


271/274


272/274


273/274


274/274

Organophosphorus Reagents

Documents

Transcript of Organophosphorus Reagents