Oracle Communications ASAP Alcatel A1000 DSLAM SW4.7 ...€¦ · ASDL commands ... The Alcatel...
Transcript of Oracle Communications ASAP Alcatel A1000 DSLAM SW4.7 ...€¦ · ASDL commands ... The Alcatel...
Alcatel A1000 DSLAMSW4.7 Cartridge Guide
Second EditionOctober 2008
Oracle Communications® ASAP™ Cartridge 1.0 for Alcatel A1000 DSLAM
Copyright and Trademark Information
Copyright © 1992, 2008, Oracle and/or its affiliates. All rights reserved.Oracle is a registered trademark of Oracle Corporation and/or its affiliates. Other names may be trademarks of their respective owners.
This software and related documentation are provided under a license agreement containing restrictions on use and disclosure and are protected by intellectual property laws. Except as expressly permitted in your license agreement or allowed by law, you may not use, copy, reproduce, translate, broadcast, modify, license, transmit, distribute, exhibit, perform, publish or display any part, in any form, or by any means. Reverse engineering, disassembly, or decompilation of this software, unless required by law for interoperability, is prohibited.The information contained herein is subject to change without notice and is not warranted to be error-free. If you find any errors, please report them to us in writing.
If this software or related documentation is delivered to the U.S. Government or anyone licensing it on behalf of the U.S. Government, the following notice is applicable:
U.S. GOVERNMENT RIGHTS Programs, software, databases, and related documentation and technical data delivered to U.S. Government customers are "commercial computer software" or "commercial technical data" pursuant to the applicable Federal Acquisition Regulation and agency-specific supplemental regulations. As such, the use, duplication, disclosure, modification, and adaptation shall be subject to the restrictions and license terms set forth in the applicable Government contract, and, to the extent applicable by the terms of the Government contract, the additional rights set forth in FAR 52.227-19, Commercial Computer Software License (December 2007). Oracle USA, Inc., 500 Oracle Parkway, Redwood City, CA 94065.This software is developed for general use in a variety of information management applications. It is not developed or intended for use in any inherently dangerous applications, including applications which may create a risk of personal injury. If you use this software in dangerous applications, then you shall be responsible to take all appropriate fail-safe, backup, redundancy and other measures to ensure the safe use of this software. Oracle Corporation and its affiliates disclaim any liability for any damages caused by use of this software in dangerous applications.
This software and documentation may provide access to or information on content, products and services from third parties. Oracle Corporation and its affiliates are not responsible for and expressly disclaim all warranties of any kind with respect to third party content, products and services. Oracle Corporation and its affiliates will not be responsible for any loss, costs, or damages incurred due to your access to or use of third party content, products or services.
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 3
Contents1. Cartridge Overview ...................................................................................... 1
Cartridge content ................................................................................................................... 2Prerequisites ......................................................................................................................... 2About this guide .................................................................................................................... 2Services, features, and options ............................................................................................. 3Hardware and software requirements ................................................................................... 6Network element (NE) interface ............................................................................................ 6ASAP version ........................................................................................................................ 6Connecting to the NE ............................................................................................................ 6
2. Installing and Testing the Cartridge ........................................................... 7Downloading the cartridge .................................................................................................... 7Starting ASAP ....................................................................................................................... 8Installing the cartridge using scripts ...................................................................................... 8Uninstalling the cartridge using scripts .................................................................................. 9Testing the cartridge installation ........................................................................................... 9
Configuring loopback and live mode parameters ......................................................... 10Modifying Alcatel_DSLAM_SW4_7_ne_config.xml ...................................................... 11Testing the installation .................................................................................................. 13
3. Atomic Service Description Layer (ASDL) Commands .......................... 15ASDL commands ................................................................................................................ 17
A_ALA-A1000_SW4-7_ACT_ADSL-PROFILE ............................................................. 18A_ALA-A1000_SW4-7_ACT_CRS-VC ......................................................................... 20A_ALA-A1000_SW4-7_ACT_CRS-VP ......................................................................... 21A_ALA-A1000_SW4-7_ADD_ADSL-COMMON-PROFILE .......................................... 23A_ALA-A1000_SW4-7_ADD_ADSL-DMT-PROFILE ................................................... 25A_ALA-A1000_SW4-7_ADD_ADSL-DOWNSTREAM-PROFILE ................................. 27A_ALA-A1000_SW4-7_ADD_ADSL-LINE-PROFILE ................................................... 30A_ALA-A1000_SW4-7_ADD_ADSL-PORT .................................................................. 32A_ALA-A1000_SW4-7_ADD_ADSL-PROFILE ............................................................ 34A_ALA-A1000_SW4-7_ADD_ADSL-UPSTREAM-PROFILE ....................................... 36A_ALA-A1000_SW4-7_ADD_ATM-PORT .................................................................... 38A_ALA-A1000_SW4-7_ADD_ATM-PVCL-LT ............................................................... 41A_ALA-A1000_SW4-7_ADD_ATM-PVCL-NT .............................................................. 43A_ALA-A1000_SW4-7_ADD_ATM-PVPL .................................................................... 45A_ALA-A1000_SW4-7_ADD_ATMACC-PROFILE ....................................................... 48A_ALA-A1000_SW4-7_ADD_CAC-PROFILE .............................................................. 50A_ALA-A1000_SW4-7_ADD_CDVT-PROFILE ............................................................ 53A_ALA-A1000_SW4-7_ADD_CRS-VC ......................................................................... 55A_ALA-A1000_SW4-7_ADD_CRS-VP ......................................................................... 57A_ALA-A1000_SW4-7_ADD_OC3-INTERFACE ......................................................... 59A_ALA-A1000_SW4-7_ADD_SHDSL-PARAMETERS ................................................ 61A_ALA-A1000_SW4-7_ADD_SIG-CHANNEL .............................................................. 64
4 Oracle Corporation
A_ALA-A1000_SW4-7_ADD_SIG-CHANNEL-PARAMS ............................................. 67A_ALA-A1000_SW4-7_ADD_SVC-USER .................................................................... 70A_ALA-A1000_SW4-7_ADD_T1DS1-INTERFACE ...................................................... 72A_ALA-A1000_SW4-7_ADD_T3DS3-INTERFACE ...................................................... 74A_ALA-A1000_SW4-7_ADD_TRAFFDESC-PROFILE ................................................ 76A_ALA-A1000_SW4-7_ADD_XDSL-PORT .................................................................. 79A_ALA-A1000_SW4-7_DEACT_CRS-VC .................................................................... 81A_ALA-A1000_SW4-7_DEACT_CRS-VP .................................................................... 83A_ALA-A1000_SW4-7_DEL_ADSL-PORT .................................................................. 85A_ALA-A1000_SW4-7_DEL_ATM-PVCL-LT ............................................................... 86A_ALA-A1000_SW4-7_DEL_ATM-PVCL-NT ............................................................... 88A_ALA-A1000_SW4-7_DEL_ATM-PVPL ..................................................................... 89A_ALA-A1000_SW4-7_DEL_ATMACC-PROFILE ....................................................... 91A_ALA-A1000_SW4-7_DEL_CAC-PROFILE ............................................................... 92A_ALA-A1000_SW4-7_DEL_CDVT-PROFILE ............................................................. 94A_ALA-A1000_SW4-7_DEL_CRS-VC ......................................................................... 95A_ALA-A1000_SW4-7_DEL_CRS-VP ......................................................................... 97A_ALA-A1000_SW4-7_DEL_DSL-PROFILE ............................................................... 99A_ALA-A1000_SW4-7_DEL_SIG-CHANNEL ............................................................ 100A_ALA-A1000_SW4-7_DEL_SVC-USER .................................................................. 102A_ALA-A1000_SW4-7_DEL_TRAFFDESC-PROFILE ............................................... 103A_ALA-A1000_SW4-7_DEL_XDSL-PORT ................................................................ 104A_ALA-A1000_SW4-7_MOD_SHDSL-PARAMETERS .............................................. 106
4. Service Definition ..................................................................................... 109CSDL commands .............................................................................................................. 111
C_ALA-A1000_SW4-7_ACT_ADSL-PROFILE ........................................................... 112C_ALA-A1000_SW4-7_ACT_CRS-VC ....................................................................... 113C_ALA-A1000_SW4-7_ACT_CRS-VP ....................................................................... 114C_ALA-A1000_SW4-7_ADD_ADSL-COMMON-PROFILE ........................................ 115C_ALA-A1000_SW4-7_ADD_ADSL-DMT-PROFILE ................................................. 116C_ALA-A1000_SW4-7_ADD_ADSL-DOWNSTREAM-PROFILE ............................... 118C_ALA-A1000_SW4-7_ADD_ADSL-LINE-PROFILE ................................................. 120C_ALA-A1000_SW4-7_ADD_ADSL-PORT ................................................................ 122C_ALA-A1000_SW4-7_ADD_ADSL-PROFILE .......................................................... 123C_ALA-A1000_SW4-7_ADD_ADSL-UPSTREAM-PROFILE ..................................... 129C_ALA-A1000_SW4-7_ADD_ATM-PORT ................................................................. 130C_ALA-A1000_SW4-7_ADD_ATM-PVCL-LT ............................................................. 132C_ALA-A1000_SW4-7_ADD_ATM-PVCL-NT ............................................................ 134C_ALA-A1000_SW4-7_ADD_ATM-PVPL .................................................................. 135C_ALA-A1000_SW4-7_ADD_ATMACC-PROFILE .................................................... 137C_ALA-A1000_SW4-7_ADD_CAC-PROFILE ............................................................ 139C_ALA-A1000_SW4-7_ADD_CDVT-PROFILE .......................................................... 141C_ALA-A1000_SW4-7_ADD_CRS-VC ...................................................................... 142C_ALA-A1000_SW4-7_ADD_CRS-VP ....................................................................... 143C_ALA-A1000_SW4-7_ADD_OC3-INTERFACE ....................................................... 144C_ALA-A1000_SW4-7_ADD_SHDSL-PARAMETERS .............................................. 146C_ALA-A1000_SW4-7_ADD_SIG-CHANNEL ............................................................ 147
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 5
C_ALA-A1000_SW4-7_ADD_SIG-CHANNEL-PARAMS ........................................... 149C_ALA-A1000_SW4-7_ADD_SVC-USER .................................................................. 151C_ALA-A1000_SW4-7_ADD_T1DS1-INTERFACE ................................................... 153C_ALA-A1000_SW4-7_ADD_T3DS3-INTERFACE ................................................... 154C_ALA-A1000_SW4-7_ADD_TRAFFDESC-PROFILE .............................................. 155C_ALA-A1000_SW4-7_ADD_XDSL-PORT ................................................................ 157C_ALA-A1000_SW4-7_DEACT_CRS-VC .................................................................. 159C_ALA-A1000_SW4-7_DEACT_CRS-VP .................................................................. 160C_ALA-A1000_SW4-7_DEL_ADSL-PORT ................................................................ 161C_ALA-A1000_SW4-7_DEL_ATM-PVCL-LT ............................................................. 162C_ALA-A1000_SW4-7_DEL_ATM-PVCL-NT ............................................................. 163C_ALA-A1000_SW4-7_DEL_ATM-PVPL ................................................................... 164C_ALA-A1000_SW4-7_DEL_ATMACC-PROFILE ..................................................... 165C_ALA-A1000_SW4-7_DEL_CAC-PROFILE ............................................................. 166C_ALA-A1000_SW4-7_DEL_CDVT-PROFILE .......................................................... 167C_ALA-A1000_SW4-7_DEL_CRS-VC ....................................................................... 168C_ALA-A1000_SW4-7_DEL_CRS-VP ....................................................................... 169C_ALA-A1000_SW4-7_DEL_DSL-PROFILE ............................................................. 170C_ALA-A1000_SW4-7_DEL_SIG-CHANNEL ............................................................ 171C_ALA-A1000_SW4-7_DEL_SVC-USER .................................................................. 172C_ALA-A1000_SW4-7_DEL_TRAFFDESC-PROFILE ............................................... 173C_ALA-A1000_SW4-7_DEL_XDSL-PORT ................................................................ 174C_ALA-A1000_SW4-7_MOD_SHDSL-PARAMETERS ............................................. 175
5. Configuring ASAP to Support Additional NE Instances ...................... 177Extracting source files ....................................................................................................... 181
Loading a new XML file .............................................................................................. 181
6 Oracle Corporation
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 1
1
Cartridge Overview
ASAP cartridges are discrete software components that are developed for the ASAP product. An ASAP cartridge offers specific domain behavior on top of the core ASAP software, and provides the configuration that supports a set of services on a network element (NE).
An ASAP cartridge is not a stand-alone component, but operates in conjunction with the ASAP core product. ASAP cartridges offer the following benefits:
Reduced Time to Market - time to market of new services is reduced through simplified development, implementation, and extension of cartridges on customer sites.Extendable - cartridges can be extended to include additional services and components that deliver business value, without requiring changes to the original cartridge.Simplified Effort - the effort and technical knowledge that is required to perform customizations is reduced.Ease of Installation - cartridges can be installed into an ASAP environment without interfering with the existing install base.
An ASAP cartridge can be used to configure ASAP to provision the following:
NEs from a specific vendor, such as Nortel or Lucent.Technologies, such as Asynchronous Transfer Mode (ATM) and Frame Relay switches, or Internet Protocol (IP) routers.Services that are supported on the NE, such as ATM, IP Virtual Private Networks (VPN), Wireless, or Optical.
An ASAP cartridge supports a particular set of services on an NE. These services are independent of customer-specific service definitions. Professional Services or systems integrators can perform extensions to the cartridge to support customer-specific requirements.
For more information on extending a cartridge, refer to the ASAP Cartridge Development Guide for Service Activation.
Cartridges are designed for a specific technology, software load, and service.
Chapter 1: Cartridge Overview
2 Oracle Corporation
Cartridge contentAn ASAP cartridge contains the following:
An interface to the NEA set of scripts, such as State Tables or Java methodsA set of atomic actions in the form of Atomic Service Description Layer (ASDL) commandsA set of Common Service Description Layer (CSDL) commands that form meaningful servicesSample work ordersInstallation scripts
PrerequisitesSystem integrators such as managers, designers, programmers, and testers who are responsible for the adaptation and integration of ASAP-based solutions should use this manual as a reference. It assumes that readers possess the following skills:
A knowledge of ASAP programming conceptsA good working knowledge of the UNIX operating systemA thorough understanding of service and network provisioningFamiliarity with telecommunications
About this guideThis guide provides a detailed description of the Alcatel A1000 DSLAM cartridge. It contains overview and technical information to assist with extending and integrating the cartridge into a customer environment.
The scope of this guide includes ASAP as it pertains to the use of this cartridge. It is not intended to be a complete ASAP reference guide.
For additional information when using this cartridge, refer to the following supporting documentation:
Activation documentation set—for detailed information on the ASAP component.ASAP Cartridge Development Guide for Service Activation—for information on how to extend a cartridge.
The Alcatel A1000 DSLAM cartridge provides the ASAP service configuration and network element (NE) interface to activate provisioning services on ALA_DSL_HOST NEs.
Services, features, and options
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 3
Services, features, and optionsThis cartridge supports the following services:
Configures ATM servicesConfigures DSL servicesConfigures InterfacesConfigures Switched Virtual Circuit
The following table lists the supported services and its features.
Table 1: Supported Services
Service Description
ATM Services
Configure ATM Port This service configures the data associated with ATM ports (NT or LT) on NE.
Create a VCL Link This service creates a Virtual Channel Link on an NT or LT interface.
Remove a VCL Link This service removes a Virtual Channel Link from an NT or LT interface.
Create a VPL Link This service creates a Virtual Path Link on an NT or LT interface.
Remove a VPL Link This service removes a Virtual Path Link from an NT or LT interface.
Create a VC cross-connect This service creates a VC level cross connection between NT and LT cards.
Activate VC cross-connect This service activates the VC cross connect previously created.
Deactivate VC cross-connect This service deactivates a VC cross connect.
Remove a VC cross-connect This service removes a VC cross connection between NT and LT cards.
Create a VP cross-connect This service creates a VP cross-connection between NT and LT cards.
Activate a VP cross-connect This service activates a VP cross connection.
Deactivate a VP cross-connect This service deactivates a VP cross connection.
Chapter 1: Cartridge Overview
4 Oracle Corporation
Remove a VP cross-connect This service removes a VP cross-connection between NT and LT card.
Create Access Profile This service creates an ATM access profile.
Remove Access Profile This service removes an ATM access profile.
Create CAC Profile This service creates an ATM connection admission control profile.
Remove CAC Profile This service removes an ATM connection admission control profile.
Create CDVT Profile This service creates an ATM cell delay variance tolerance profile for Switched Virtual Circuit (SVC) connections.
Remove CDVT Profile This service removes an ATM cell delay variation tolerance profile for Switched Virtual Circuit (SVC) connections.
Create Traffic Descriptor Profile This service creates an ATM traffic descriptor profile.
Remove Traffic Descriptor Profile This service removes an ATM traffic descriptor profile.
DSL Services
Configure ADSL (LT) Port This service configures provisioning data associtated with an ADSL facility on an LT card.
Remove ADSL (LT) Port This service unassigns (free) an ADSL port used by a user.
Create ADSL Line Profile This service configures ADSL line profile.
Create ADSL COM Profile This service configures ADSL modem provisioning parameters that are common to both upstream and downstream directions in a newly created (inactivated) ADSL profile.
Create ADSL DN Profile This service configures ADSL line provisioning parameters for the downstream direction (from ATU-C to ATU-R) in a newly created (inactivated) ADSL profile.
Create ADSL UP Profile This service configures ADSL line provisioning parameters for the upstream direction (from ATU-R to ATU-C) in a newly created (inactivated) ADSL profile.
Create ADSL DMT Profile This service configures the ADSL DMT (Discrete Multi-Tone) carrier-mask in a newly created ADSL profile.
Table 1: Supported Services
Service Description
Services, features, and options
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 5
Activate ADSL Profile This service activates the newly created ADSL profile.
Create ADSL Profile The ADSL profile is created by the following steps:
Allocate a new profile using the ENT-PROFILE-ADSL command Configure downstream transmissionparameters using ED-PROFILE-ADSLDN Configure upstream transmissionparameters using ED-PROFILE-ADSLUP Configure common transmissionparameters using ED-PROFILE-ADSLCOM Configure the DMT (Discrete Multi-Tone) Carrier Mask using ED-PROFILE-AD SLMSK
The profile is activated using ACT-PROFILE-ADSL
Delete DSL Profile This service removes an ADSL profile.
Configure SHDSL parameters This service configures provisioning parameters associated with an SHDSL facility.
Modify SHDSL parameters This service modifies the provisioning parameters associated with an SHDSL facility.
Configure XDSL (LT) port This service configures the provisioning data associtated with an XDSL facility on an LT card.
Remove XDSL (LT) port This service unassigns (free) an XDSL port used by an user.
Interface Services
Configure T1/DS1 interface parameters This service configures T1/DS1 interface parameters.
Configure T3/DS3 interface parameters This service configures T3/DS3 interface parameters.
Configure OC3 interface parameters This service configures OC3 interface parameters.
Switched Virtual Circuit Services
Create Signaling Channel This service adds a new signaling channel.
Configure Signaling Channel This service configures the parameters associated with signaling channel.
Table 1: Supported Services
Service Description
Chapter 1: Cartridge Overview
6 Oracle Corporation
Hardware and software requirementsThe following sections contain the high-level software and hardware environment requirements for provisioning services including:
Network element (NE) interfaceASAP versionOperating environment
Network element (NE) interfaceThis cartridge is designed to operate with the ALA_DSL_HOST NEs.
ASAP versionThis cartridge was developed and tested using ASAP 5.0.
For information on the operating environment, refer to the ASAP Release Record.
Connecting to the NEThe ASAP cartridge interfaces with the Alcatel A1000 & LiteSpan DSLAMs using the Alcatel 5526 Access Management System (AMS) system via TL1 over TCP/IP.
Delete Signaling Channel This service removes the parameters associated with signaling channel.
Configure SVC User This service adds a Switched Virtual Circuit (SVC) user.
Delete SVC User This service removes the parameters associated with Switched Virtual Circuit (SVC) user.
Table 1: Supported Services
Service Description
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 7
2
Installing and Testing the Cartridge
This chapter describes the following procedures related to installing and testing the cartridge:
Downloading the cartridgeInstalling the cartridge using scriptsUninstalling the cartridge using scriptsTesting the cartridge installation
Downloading the cartridgeBefore you install the cartridge, you must use the internet to download the cartridge’s TAR file from Oracle’s Customer Portal.
Use the following instructions to download, then unTAR the TAR file.
To download the TAR file
1. Login to Oracle MetaLink internet home page (http://www.metalink.oracle.com).
2. Download the cartridge patch to your workstation.
To unTAR the TAR file
1. On your workstation, create a repository directory—the naming of which is your choice.mkdir <repository dir>
2. Untar AlcatelA1000_SW4_7_R1_0_0.<buildID>.tar.tar xvf AlcatelA1000_SW4_7_R1_0_0.<buildID>.tar
3. Copy the resulting /Alcatel_DSLAM_SW4_7 directory and its contents to the repository directory.
cp -rf /Alcatel_DSLAM_SW4_7 <repository_dir>
The directory structure in the repository directory should look like the following illustration. (this illustration describes the minimum required structure; you can enhance this directory structure with additional directories based on your requirements and deliverables). <repository_directory>
/README.txt/installCartridge/uninstallCartridge
Chapter 2: Installing and Testing the Cartridge
8 Oracle Corporation
/Alcatel_DSLAM_SW4_7.sar
Starting ASAPBefore installing the cartridge, ensure that ASAP is running.
To start ASAP
1. To start ASAP, execute the following script:start_asap_sys -d
2. Ensure the ASAP Daemon (DAEM$ENV_ID) is running by checking the ASAP status using the ASAP script “status”.
3. Check whether the WebLogic instance for this ASAP environment is running. If not, start the WebLogic instance.
The ASAP Administration Guide contains more information on starting ASAP, the ASAP Daemon, and WebLogic.
Installing the cartridge using scriptsRun the installation script installCartridge to install the cartridge. The script executes the following tasks:
Configures a new Alcatel A1000 DSLAM-specific NEP using the Service Activation Configuration Tool or SACT.Configures the Alcatel A1000 DSLAM-specific NE using the SACT. Deploys the Alcatel A1000 DSLAM cartridge service model (only if the Alcatel A1000 DSLAM service model is not yet deployed) using the Service Activation Deployment Tool (SADT).Copies the Alcatel A1000 DSLAM-specific jar files and the cpp library file to the ASAP environment.Loads the sample work orders to the SRP database.
For information on the SACT and the SADT, refer to the ASAP Administration Guide.
To install the cartridge
1. Run the installCartridge script. At the prompt, type:installCartridge Alcatel_DSLAM_SW4_7.sar
2. The script prompts you for the values of the following WebLogic login parameters:
WebLogic HostnameWebLogic HTTP PortWebLogic Login User IDWebLogic Login Password
Uninstalling the cartridge using scripts
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 9
The script loads the NEP-NE configuration and the CSDL-ASDL configuration to the SARM database, and loads sample work orders to the SRP database. The script also copies the cartridge-specific jar files and cpp library file to the ASAP environment.
3. Restart ASAP to upload the cartridge configuration into ASAP.
Uninstalling the cartridge using scriptsRun the uninstallation script uninstallCartridge to uninstall the Alcatel A1000 DSLAM cartridge. The script executes the following tasks:
Unconfigures Alcatel A1000 DSLAM-specific NEs using the SACT. Undeploys the Alcatel A1000 DSLAM cartridge service model (only if the Alcatel A1000 DSLAM service model is already deployed) using the Service Activation Deployment Tool (SADT). Removes the Alcatel A1000 DSLAM-specific jar files and cpp library file from the ASAP environment.
For more information on the SACT and the SADT, refer to the ASAP Administration Guide.
To uninstall the cartridge
1. Run the uninstallCartridge script. At the prompt, type:uninstallCartridge Alcatel_DSLAM_SW4_7.<timestamp>.sar
2. The script prompts you for the values of the following parameters:
WebLogic HostnameWebLogic HTTP PortWebLogic Login User IDWebLogic Login Password
The script unloads the NEP-NE configuration and CSDL-ASDL configuration from SARM database. It also removes the cartridge specific jar files and cpp library file from the ASAP environment.
Testing the cartridge installationTo test this cartridge installation, you need to know about the network element (NE), services, and basic Activation configuration. You may need to perform adjustments to provision a service for a specific NE, network, or connectivity configuration.
You can test the cartridge installation using one of the following methods:
Loopback mode—does not actually connect to or send commands to the NE.Live mode—connects to and sends commands to a live NE.
Chapter 2: Installing and Testing the Cartridge
10 Oracle Corporation
Configuring loopback and live mode parametersSet the following variables to test the cartridge in loopback or live testing modes.
Loopback mode
Set the following parameter to test the cartridge in loopback mode.
Live mode
Set the following parameter to test the cartridge in live mode.
Communication parameters
The following are the list of parameters for the sample NE configuration XML used by SACT.
Table 2: Loopback Mode Parameter Settings
Configuration Variable Parameter Settings Location
LOOPBACK_ON 1 (default setting) ASAP.cfg
Table 3: Live Mode Parameter Settings
Configuration Variable Parameter Settings Location
LOOPBACK_ON 0 ASAP.cfg
Table 4: Communication parameters
paramlabel param_value param_desc
HOSTIPADDR 10.1.9.222 JNEP IP address.
HOSTNAME sloth JNEP hostname.
AMS_PORT 23 Port number to connect on remote NE host.
OPENTIMEOUT 20 Socket connection timeout (in seconds).
READTIMEOUT 30 Socket read timeout (in seconds).
AMSJJSER asap Username for the AMS user.
AMS_PASSWORD asap Password for the AMS user.
Testing the cartridge installation
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 11
Modifying Alcatel_DSLAM_SW4_7_ne_config.xmlUse the following procedure to modify Alcatel_DSLAM_SW4_7_ne_config.xml.
To modify Alcatel_DSLAM_SW4_7_ne_config.xml
1. Create a new source directory. You can give this directory any appropriate, meaningful name you want to.
mkdir <new_source_directory>
2. Copy Alcatel_DSLAM_SW4_7.sar to this new source directory.
cp Alcatel_DSLAM_SW4_7.sar ./<new_source_directory>
3. Change directory to <new_source_directory>.cd <new_source_directory>
4. Un-jar Alcatel_DSLAM_SW4_7.sar. This extracts the contents of the sar file.
jar xvf Alcatel_DSLAM_SW4_7.sar
5. Edit Alcatel_DSLAM_SW4_7_ne_config.xml with the appropriate changes, which is available under <new_source_directory>/NetworkElements.
6. Create a new sar file at the <new_source_directory> level. CreateSar $PWD
7. Uninstall the cartridge using Alcatel_DSLAM_SW4_7.sar. (That is, use the original sar file that you copied in Step 2 above—see “Uninstalling the cartridge using scripts” on page 9 for uninstallation instructions).
8. After you uninstall the cartridge, rename the sar file, so you have a backup copy of it.
9. Copy the new sar file from <new_source_directory>.
10. Reinstall the cartridge (see “Installing the cartridge using scripts” on page 8 for installation instructions).
AMS_PORT 14000 AMS listening port for the socket connection.
AMS_TID PSALIDI TID of target device.
AMSJJID SUPERUSER User name of target device.
AMS_PID ANS#150 Password of target device.
AMS_CTAG 1 CTAG of target device.
Table 4: Communication parameters
paramlabel param_value param_desc
Chapter 2: Installing and Testing the Cartridge
12 Oracle Corporation
File Structure of the Un-Jared .sar File
Testing the cartridge installation
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 13
Testing the installationThe following procedure describes the steps required to test the cartridge installation in loopback mode. We recommend that you perform the initial cartridge installation test in loopback mode.
To test in loopback mode
1. Stop ASAP by typing the following command at the UNIX prompt:stop_asap_sys -d
2. Ensure loop back mode is on. See “Loopback mode” on page 10 for a description of how to set the loop back parameter to “On”.
3. Start ASAP by typing:start_asap_sys -d
4. Send the sample work orders through the SRP Emulator by typing:run_suite $SRP <ctrl_password> <suite name>
You can locate the suite names by typing:grep SUITE * | grep -v END
A list of all available suites appears.
For more information on the SRP Emulator, refer to the ASAP Administration Guide.
5. Verify the status of the sample work orders by typing:asap_utils -d l
All successful work orders returns to the 104 state.
To view the sample work orders provided with this cartridge, refer to the Alcatel A1000 DSLAM cartridge source.
Viewing the sample work orders
You can find the sample work orders under the SampleWorkOrders directory in the sar file. The following procedure describes how to view the sample work orders.
To view the sample work orders
1. Create a repository directory, copy the sar file to the new directory and un-jar the sar file, as described by Step 1 through Step 4 in “Modifying Alcatel_DSLAM_SW4_7_ne_config.xml” on page 11.
2. Locate and view the sample work order files under /Alcatel_DSLAM_SW4_7/../sample_wo.
Chapter 2: Installing and Testing the Cartridge
14 Oracle Corporation
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 15
3
Atomic Service Description Layer (ASDL) Commands
ASDL commands represent a set of atomic actions that ASAP can perform on a network element (NE). ASAP can combine ASDLs to create meaningful services (CSDLs) within a cartridge.
This chapter presents detailed information on the ASDL parameters that we provide with this cartridge. The following table lists and describes the type of parameter information that is included.
Table 5: ASDL parameter information
Item Description
Parameter Name Identifies the parameter that is configured for the stated service.
Description Describes the parameter.
Range Describes or lists the range of values that can be used to satisfy this parameter.
Default Value Configures a default value for the parameter so that it is not mandatory for the upstream system to provide a value.
Chapter 3: Atomic Service Description Layer (ASDL) Commands
16 Oracle Corporation
For a detailed description of the Required and Optional parameter classifications, refer to the ASAP Administration Guide.
Type Indicates one of the following parameter types:
S—Scalar, specifies the parameter label transmitted on the ASDL command. Scalar parameters are conventional name-value pair parameters.C—Compound, specifies the base name of the compound parameter transmitted on the ASDL command. A compound parameter contains structures or arrays of information that are represented by a particular structure name or compound parameter name. Each compound parameter can contain a large number of elements. If you use compound parameters, you only require a single entry in the ASAP translation tables to call the compound parameter and all its associated parameter elements.I—Indexed, identifies a parameter that contains a sequential numerical index value to tell the SARM that it should execute the same operation (for example, an ASDL command) for all occurrences of that index. Consequently, if there are several options on a particular CSDL command (OPT1, OPT2, OPT3, etc.), you can specify the OPT parameter as an indexed parameter. When you specify the OPT parameter as an indexed parameter, the SARM generates several occurrences of that same ASDL command and each command has a different value for the option being transmitted to the NEP.
For more information on parameter types, refer to the ASAP Developer Reference.
Class Indicates one of the following parameter classifications:
R—Required scalar parameterO—Optional scalar parameterC—Required compound parameterN—Optional compound parameterM—Mandatory indexed parameterI—Optional indexed parameterS—Parameter count
Table 5: ASDL parameter information
Item Description
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 17
ASDL commandsThis cartridge provides the following ASDL commands:
A_ALA-A1000_SW4-7_ACTADSL-PROFILEA_ALA-A1000_SW4-7_ACT_CRS-VCA_ALA-A1000_SW4-7_ACT_CRS-VPA_ALA-A1000_SW4-7_ADD_ADSL-COMMON-PROFILEA_ALA-A1000_SW4-7_ADD_ADSL-DMT-PROFILEA_ALA-A1000_SW4-7_ADD_ADSL-DOWNSTREAM-PROFILEA_ALA-A1000_SW4-7_ADD_ADSL-LINE-PROFILEA_ALA-A1000_SW4-7_ADD_ADSL-PORTA_ALA-A1000_SW4-7_ADD_ADSL-PROFILEA_ALA-A1000_SW4-7_ADD_ADSL-UPSTREAM-PROFILEA_ALA-A1000_SW4-7_ADD_ATM-PORTA_ALA-A1000_SW4-7_ADD_ATM-PVCL-LTA_ALA-A1000_SW4-7_ADD_ATM-PVCL-NTA_ALA-A1000_SW4-7_ADD_ATM-PVPLA_ALA-A1000_SW4-7_ADD_ATMACC-PROFILEA_ALA-A1000_SW4-7_ADD_CAC-PROFILEA_ALA-A1000_SW4-7_ADD_CDVT-PROFILEA_ALA-A1000_SW4-7_ADD_CRS-VCA_ALA-A1000_SW4-7_ADD_CRS-VPA_ALA-A1000_SW4-7_ADD_OC3-INTERFACEA_ALA-A1000_SW4-7_ADD_SHDSL-PARAMETERSA_ALA-A1000_SW4-7_ADD_SIG-CHANNELA_ALA-A1000_SW4-7_ADD_SIG-CHANNEL-PARAMSA_ALA-A1000_SW4-7_ADD_SVC-USERA_ALA-A1000_SW4-7_ADD_T1DS1-INTERFACEA_ALA-A1000_SW4-7_ADD_T3DS3-INTERFACEA_ALA-A1000_SW4-7_ADD_TRAFFDESC-PROFILEA_ALA-A1000_SW4-7_ADD_XDSL-PORTA_ALA-A1000_SW4-7_DEACT_CRS-VCA_ALA-A1000_SW4-7_DEACT_CRS-VPA_ALA-A1000_SW4-7_DEL_ADSL-PORTA_ALA-A1000_SW4-7_DEL_ATM-PVCL-LTA_ALA-A1000_SW4-7_DEL_ATM-PVCL-NT
Chapter 3: Atomic Service Description Layer (ASDL) Commands
18 Oracle Corporation
A_ALA-A1000_SW4-7_DEL_ATM-PVPLA_ALA-A1000_SW4-7_DEL_ATMACC-PROFILEA_ALA-A1000_SW4-7_DEL_CAC-PROFILEA_ALA-A1000_SW4-7_DEL_CDVT-PROFILEA_ALA-A1000_SW4-7_DEL_CRS-VCA_ALA-A1000_SW4-7_DEL_CRS-VPA_ALA-A1000_SW4-7_DEL_DSL-PROFILEA_ALA-A1000_SW4-7_DEL_SIG-CHANNELA_ALA-A1000_SW4-7_DEL_SVC-USERA_ALA-A1000_SW4-7_DEL_TRAFFDESC-PROFILEA_ALA-A1000_SW4-7_DEL_XDSL-PORTA_ALA-A1000_SW4-7_MOD_SHDSL-PARAMETERS
A_ALA-A1000_SW4-7_ACT_ADSL-PROFILEActivates an Asymmetric Digital Subscriber Line (ADSL) profile. It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.DSLProv.actDSLProfile
Table 6: A_ALA-A1000_SW4-7_ACT_ADSL-PROFILE
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
ADSLACT_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.Default value: NULL
S O
ADSLACT_PROFILE_ID
The ADSL profile index. 1 to 40 S R
ADSLACT_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 19
MML CommandsACT-PROFILE-ADSL:<ADSLACT_TID>:< ADSLACT_PROFILE_ID>:< ADSLACT_CTAG>[:];
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>
Output Parameters
None.
Chapter 3: Atomic Service Description Layer (ASDL) Commands
20 Oracle Corporation
A_ALA-A1000_SW4-7_ACT_CRS-VCActivates a virtual circuit cross connect.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.actCrsVc
MML CommandsENT-CRS-VC:<VCCC_TID>: NTVCL-<NT_VCL.VPI>-<NT_VCL.VCI >, LTVCL-
<LT_VCL.LTVCL.RACK>-< LT_VCL.LTVCL.SHELF>-<LT_VCL.LTVCL.LTSLOT>-<
LT_VCL.LTVCL.CIRCUIT>-< LT_VCL.LTVCL.VPI>-<LT_VCL.LTVCL.VCI>:<
VCCC_CTAG>::::IS;
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
Table 7: A_ALA-A1000_SW4-7_ACT_CRS-VC
Parameter Name
Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
VCCC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.Default value: NULL
S O
VCCC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
NT_VCL Access identifier for the ATM virtual channel link in the NT/Server.
C R
LT_VCL Access identifier for the ATM virtual channel link in the LT/Server.
C R
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 21
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message header><crxlf>
M/s/s<ctag>/sCOMPLD<cr><lf>
AAA/* <command echo */ <crxlf>;
Output Parameters
None.
A_ALA-A1000_SW4-7_ACT_CRS-VPActivates a virtual path cross connect.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.actCrsVp
Table 8: A_ALA-A1000_SW4-7_ACT_CRS-VP
Parameter Name
Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
VPCC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NT_VPL Access identifier for the ATM virtual path link in the NT.
C R
LT_VPL Access identifier for the ATM virtual path link in the LT/Server.
C R
Chapter 3: Atomic Service Description Layer (ASDL) Commands
22 Oracle Corporation
MML CommandsENT-CRS-VP:<VPCC_TID>:<NT_VPL>,<LT_VPL>:<VPCC_CTAG>::::IS;
Where, NT_VPL will have the following format:
VPL in NT:NTVPL-<NT_VPL.NTVPL. VPI>
Where, LTVPL will have one of the following format:
VPL in the Server:SERWPL-<LT_VPL.SERWPL.RACK>-<LT_VPL.SERWPL.SHELF >-<LT_VPL.SERWPL.SERV_SLOT>-<LT_VPL.SERWPL.CIRCUITX <LT_VPL.SERWPL.VPI>
LT Circuits:LTVPL-<LT_VPL.LTVPL.RACK>-<LT_VPL.LTVPL.SHELF>-<LT_VPL.LTVPL.LT_SLOT>-<LT_VPL.LTVPL.CIRCUIT>-<LT_VPL.LTVPL.VPI>
LT IMA Groups:LTIMAVPLXLT VPL.LTIMAVPL.RACK>-<LT_VPL.LTIMAVPL.SHELF>-<LT_VPL.LTIMAVPL.LT_SLOT>-<LT_VPL.LTIMAVPL.IMAGRPX <LT_VPL.LTIMAVPL.VPI>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
MAA<ctag>ADENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
VPCC_CTAG
The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.Default value: 0
S O
Table 8: A_ALA-A1000_SW4-7_ACT_CRS-VP
Parameter Name
Description RangeDefault Value
Type Class
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 23
AAA<message header><crxlf>
M/s/s<ctag>/sCOMPLD<cr><lf>
^^^/* <command echo */ <crxlf>;
Output Parameters
None.
A_ALA-A1000_SW4-7_ADD_ADSL-COMMON-PROFILEAdds an Asymmetric Digital Subscriber Line (ADSL) common profile. It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.DSLProv.addDSLCommonProfile
Table 9: A_ALA-A1000_SW4-7_ADD_ADSL-COMMON-PROFILE
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
ADSLCOM_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
ADSLCOMP_ROFILE_ID The ADSL profile index.
1 to 40 S R
ADSLCOM_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
Chapter 3: Atomic Service Description Layer (ASDL) Commands
24 Oracle Corporation
MML CommandsED-PROFILE-ADSLCOM:<ADSLCOM_ID>:<ADSLCOM-PROFILE_ID>:<ADSLCOM_CTAG>::: <ADSLCOM_NBLK>;
Where, the ADSL line parameter block <ADSLCOM_NBLK> will contain one or more of the following named parameters separated by commas:
ALWPROPGLITE=<ADSLCOM_NBLK. ALWPROPGLITE>
ALWPROPGDMT=<ADSLCOM_NBLK. ALWPROPGDMT>
ALWPWRCTL=<ADSLCOM_NBLK. ALWPWRCTL>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>
ADSLCOM_NBLK The ADSL line parameter block containing one or more of the following named parameters with their values separated by commas:
ALWPROPGLITEALWPROPGDMTALWPWRCTL
C O
Table 9: A_ALA-A1000_SW4-7_ADD_ADSL-COMMON-PROFILE
Parameter Name Description RangeDefault Value
Type Class
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 25
Output Parameters
None.
A_ALA-A1000_SW4-7_ADD_ADSL-DMT-PROFILEAdds an Asymmetric Digital Subscriber Line (ADSL) discrete multi-tone profile. It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.DSLProv.addDSLDmtProfile
Table 10: A_ALA-A1000_SW4-7_ADD_ADSL-DMT-PROFILE
Parameter Name
Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
ADSLMSK_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
ADSLMSK_PROFILE_ID
The ADSL profile index. 1 to 40 S R
ADSLMSK_CTAG
The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
Chapter 3: Atomic Service Description Layer (ASDL) Commands
26 Oracle Corporation
MML CommandsED-PROFILE-ADSLMSK:<ADSLMSK_TID>:<ADSLMSK-PROFILE_ID>:<ADSLMSK_CTAG>::: <ADSLMSK_NBLK>;
Where, the parameter block <ADSLMSK_NBLK> will contain one or more of the following named parameters separated by commas for provisioning the ADSL DMT carrier--mask.
CMASK0=<ADSLMSK_NBLK.CMASK0>
CMASK1=<ADSLMSK_NBLK.CMASK1>
CMASK2=<ADSLMSK_NBLK.CMASK2>
CMASK3=<ADSLMSK_NBLK.CMASK3>
CMASK4=<ADSLMSK_NBLK.CMASK4>
CMASK5=<ADSLMSK_NBLK.CMASK5>
CMASK6=<ADSLMSK_NBLK.CMASK6>
CMASK7=<ADSLMSK_NBLK.CMASK7>
If the command fails, the following error response will occur on the DSLAM:
Error response<cr><lf><lf>
^^^<message header><cr><lf>
M^^<ctag>^DENY <cr><lf>
ADSLMSK_NBLK
The parameter block containing one or more of the following named parameters separated with their values by commas for provisioning the ADSL DMT carrier mask:
CMASK0CMASK1CMASK2CMASK3CMASK4CMASK5CMASK6CMASK7
C O
Table 10: A_ALA-A1000_SW4-7_ADD_ADSL-DMT-PROFILE
Parameter Name
Description RangeDefault Value
Type Class
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 27
AAA/* <command echo */ <crxlf> C^*"<AlD>:ERRCDE=<error code><cr><lf> (AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>
Output Parameters
None.
A_ALA-A1000_SW4-7_ADD_ADSL-DOWNSTREAM-PROFILEAdds an Asymmetric Digital Subscriber Line (ADSL) downstream profile. It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.DSLProv.addDSLDownstreamProfile
Table 11: A_ALA-A1000_SW4-7_ADD_ADSL-DOWNSTREAM-PROFILE
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
ADSLDN_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.Default value: NULL
S O
ADSLDN_PROFILE_ID The ADSL profile index.
1 to 40 S R
ADSLDN_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
Chapter 3: Atomic Service Description Layer (ASDL) Commands
28 Oracle Corporation
MML CommandsED-PROFILE-ADSLDN:<ADSLDN_TID>:<ADSLDN-PROFILE_ID>:<ADSLDN_CTAG>::: <ADSLPROF_NBLK>;
Where, the ADSL line parameter block <ADSLPROF_NBLK> will contain one or more of the following named parameters separated by commas:
MINNMR=<ADSLPROF_NBLK. MINNMR>
MAXNMR=<ADSLPROF_NBLK.MAXNMR>
TNMR=<ADSLPROF_NBLK.TNMR>
MAXPSD=<ADSLPROF_NBLK.MAXPSD>
MAXAPLVL=<ADSLPROF_NBLK. MAXAPLVL>
RAMODE=<ADSLPROF_NBLK.RAMODE>
PIBR=<ADSLPROF_NBLK.PIBR>
MAXIBR=<ADSLPROF_NBLK.MAXIBR>
ADSLPROF_NBLK The ADSL line parameter block containing one or more of the following named parameters with their values separated by commas:
MINNMRMAXNMRTNMRMAXPSDMAXAPLVLRAMODEPIBRMAXIBRMINIBRMAXIDELPFBRMAXFBRMINFBR
C O
Table 11: A_ALA-A1000_SW4-7_ADD_ADSL-DOWNSTREAM-PROFILE
Parameter Name Description RangeDefault Value
Type Class
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 29
MINIBR=<ADSLPROF_NBLK.MINIBR>
MAXIDEL=<ADSLPROF_NBLK.MAXIDEL> PFBR=<ADSLPROF_NBLK.PFBR> MAXFBR=<ADSLPROF_NBLK.MAXFBR> MINFBR=<ADSLPROF_NBLK. MINFBR>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>
Output Parameters
None.
Chapter 3: Atomic Service Description Layer (ASDL) Commands
30 Oracle Corporation
A_ALA-A1000_SW4-7_ADD_ADSL-LINE-PROFILEAdds an Asymmetric Digital Subscriber Line (ADSL) line profile.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.DSLProv.addDSLLineProfile
Table 12: A_ALA-A1000_SW4-7_ADD_ADSL-LINE-PROFILE
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
ADSLLP_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
ADSLLP_PROFILE_ID The ADSL profile index. 1 to 40 S R
ADSLLP_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 31
MML CommandsED-PROFILE-ADSLDN:<ADSLLP_TID>:<ADSLLP-PROFILE_ID>:<ADSLLP_CTAG>::: <ADSLPROF_NBLK>;
Where, the ADSL line parameter block <ADSLPROF_NBLK> will contain one or more of the following named parameters separated by commas:
MINNMR=<ADSLPROF_NBLK.MINNMR> MAXNMR=<ADSLPROF_NBLK. MAXNMR> TNMR=<ADSLPROF_NBLK.TNMR> MAXPSD=<ADSLPROF_NBLK.MAXPSD> MAXAPLVL=<ADSLPROF_NBLK.MAXAPLVL> PAMODE=<ADSLPROF_NBLK.RAMODE> PIBR=<ADSLPROF_NBLK.PIBR> MAXIBR=<ADSLPROF_NBLK.MAXIBR> MINIBR=<ADSLPROF_NBLK.MINIBR> MAXIDEL=<ADSLPROF_NBLK.MAXIDEL> PFBR=<ADSLPROF_NBLK.PFBR> MAXFBR=<ADSLPROF_NBLK.MAXFBR> MINFBR=<ADSLPROF_NBLK.MINFBR>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
ADSLPROF_NBLK The ADSL line parameter block containing one or more of the following named parameters with their values separated by commas:
MINNMRMAXNMRTNMRMAXPSDMAXAPLVLRAMODEPIBRMAXIBRMINIBRMAXIDELPFBRMAXFBRMINFBR
C O
Table 12: A_ALA-A1000_SW4-7_ADD_ADSL-LINE-PROFILE
Parameter Name Description RangeDefault Value
Type Class
Chapter 3: Atomic Service Description Layer (ASDL) Commands
32 Oracle Corporation
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>
Output Parameters
None.
A_ALA-A1000_SW4-7_ADD_ADSL-PORTAdds an Asymmetric Digital Subscriber Line (ADSL) port.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.DSLProv.addDSLPort
Table 13: A_ALA-A1000_SW4-7_ADD_ADSL-PORT
Table 13:
Parameter Name
Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
ADSLP_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
ADSLP_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 33
MML CommandsED-ADSL:<ADSLP_TID>: <AID_ADSL>-< ADSLP_CTAG>::: <ADSL_NBLK>:< ADSLP_PST>;
Where, access identifier for ADSL lines <AID_ADSL> is:ADSL - <AID_ADSL.RACK>-< AID_ADSL.SHELF>- < AID_ADSL.SLOT>-<AID_ADSL.CIRCUIT>
Where, the named parameter block for ADSL <ADSL_NBLK> will contain one or more of the following named parameters separated by commas:
PORTID=<ADSL_NBLK.PORTID>
ADSLPROFNM=< ADSL_NBLK. ADSLPROFNM >
ADSLPROF=< ADSL_NBLK. ADSLPROF >
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
ADSLP_PST The desired primary state to be set.
IN (In-Service)OOS (Out-Of-Service)
S O
AID_ADSL Access identifier for the ADSL line.
C R
ADSL_NBLK The ADSL line parameter block containing one or more of the following named parameters with their values separated by commas:
PORTIDADSLPROFADSLPROFNM
C O
Table 13:
Parameter Name
Description RangeDefault Value
Type Class
Chapter 3: Atomic Service Description Layer (ASDL) Commands
34 Oracle Corporation
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>
Output Parameters
None.
A_ALA-A1000_SW4-7_ADD_ADSL-PROFILEAdds an Asymmetric Digital Subscriber Line (ADSL) profile.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.DSLProv.addDSLProfile
Table 14: A_ALA-A1000_SW4-7_ADD_ADSL-PROFILE
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
ADSLPROF_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
ADSLPROF_PROFILE_ID The ADSL profile index.
1 to 40 S R
ADSLPROF_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
ADSLPROF_PROFILE_NAME
Uniquely identifies this profile within its scope.
A string, 1 to 32 characters long.
S R
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 35
MML CommandsENT—PROFILE—ADSL:<ADSLPROF_TID>:<ADSLPROF-PROFILE_ID>:<ADSLPROF_CTAG>: <ADSLPROF_PROFILE_NAME>,,<ADSLPROF_LATENCY>;
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message header><crxlf>
M/s/s<ctag>/sCOMPLD<cr><lf>
AAA/* <command echo */ <crxlf>
Output Parameters
None.
ADSLPROF_LATENCY The latency of the ADSL line.
FASTINTERLEAVED
S O
Table 14: A_ALA-A1000_SW4-7_ADD_ADSL-PROFILE
Parameter Name Description RangeDefault Value
Type Class
Chapter 3: Atomic Service Description Layer (ASDL) Commands
36 Oracle Corporation
A_ALA-A1000_SW4-7_ADD_ADSL-UPSTREAM-PROFILEAdds an Asymmetric Digital Subscriber Line (ADSL) upstream profile.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.DSLProv.addDSLUpstreamProfile
Table 15: A_ALA-A1000_SW4-7_ADD_ADSL-UPSTREAM-PROFILE
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
ADSLUP_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
ADSLUP_PROFILE_ID The ADSL profile index. 1 to 40 S R
ADSLUP_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 37
MML CommandsED-PROFILE-ADSLUP:<ADSLUP_TID>:<ADSLUP-PROFILE_ID>:<ADSLUP_CTAG>::: <ADSLPROF_NBLK>;
Where, the ADSL line parameter block <ADSLPROF_NBLK> will contain one or more of the following named parameters separated by commas:
MINNMR=<ADSLPROF_NBLK.MINNMR>
MAXNMR=<ADSLPROF_NBLK.MAXNMR>
TNMR=<ADSLPROF_NBLK.TNMR>
MAXAPLVL=<ADSLPROF_NBLK.MAXAPLVL>
PIBR=<ADSLPROF_NBLK.PIBR>
MAXIBR=<ADSLPROF_NBLK.MAXIBR>
MINIBR=<ADSLPROF_NBLK.MINIBR>
MAXIDEL=<ADSLPROF_NBLK.MAXIDEL>
PFBR=<ADSLPROF_NBLK.PFBR>
MAXFBR=<ADSLPROF_NBLK.MAXFBR>
ADSLPROF_NBLK The ADSL line parameter block containing one or more of the following named parameters with their values separated by commas:
MINNMRMAXNMRTNMRMAXAPLVLRAMODEPIBRMAXIBRMINIBRMAXIDELPFBRMAXFBRMINFBR
C O
Table 15: A_ALA-A1000_SW4-7_ADD_ADSL-UPSTREAM-PROFILE
Parameter Name Description RangeDefault Value
Type Class
Chapter 3: Atomic Service Description Layer (ASDL) Commands
38 Oracle Corporation
MINFBR=<ADSLPROF_NBLK.MINFBR>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>
Output Parameters
None.
A_ALA-A1000_SW4-7_ADD_ATM-PORTAdds an Asynchronous Transfer Mode (ATM) port.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.addATMPort
Table 16: A_ALA-A1000_SW4-7_ADD_ATM-PORT
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
ATMP_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 39
MML CommandsED-ATMPORT:<ATMP_TID>:<AID_ATMPORT>:<ATMP_CTAG>:::<ATMPORT_NBLK>:<ATMP_PST>;
Where, <AID_ATMPORT> can take one of the following values:
ATM port in NTNTATM
ATM port in a server:SERVATM - <AID_ATMPORT.SERVATM.RACK>-<AID_ATMPORT.SERVATM.SHELF>-<AID_ATMPORT.SERVATM.SERV_SLOT>- <AID_ATMPORT.SERVATM.CIRCUIT>
AID_ATMPORT Access identifier for the AT M Por t
C R
ATMPORT_NBLK The ATM Port parameter block containing one or more of the following named parameters with their values separated by commas:
IFTYPECACPROFDNCACPROFDNNMACPROFUPCACPROFUPNMATMACCPROFATMACCPROFNMCDVTPROFCDVTPROFNMNGCRWEIGHT
C O
ATMP_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
ATMP_PST The desired primary state to be set.
IS (In-Service)OOS (Out-Of-Service)
S O
Table 16: A_ALA-A1000_SW4-7_ADD_ATM-PORT
Parameter Name Description RangeDefault Value
Type Class
Chapter 3: Atomic Service Description Layer (ASDL) Commands
40 Oracle Corporation
ATM port for an LT circuit:LTATM-<AID_ATMPORT.LTATM.RACK>-<AID_ATMPORT.LTATM.SHELF>-<AID_ATMPORT.LTATM.LT_SLOT>-<AID_ATMPORT.LTATM.CIRCUIT>
ATM port for an IMA Group in the LT:LTIMAATM-<AID_ATMPORT. LTIMAATM.RACK>-<AID_ATMPORT. LTIMAATM.SHELF>-<AID_ATMPORT. LTIMAATM.LT_SLOT>-<AID_ATMPORT. LTIMAATM.IMAGRP>
Where, the ATM Port parameter block <ATMPORT_NBLK> will contain one or more of the following named parameters separated by commas:
IFTYPE=<ATMPORT_NBLK.IFTYPE>
CACPROFDN=<ATMPORT_NBLK.CACPROFDN>
CACPROFDNNM=<ATMPORT_NBLK. CACPROFDNNM>
CACPROFUP=<ATMPORT_NBLK. CACPROFUP>
CACPROFUPNM=<ATMPORT_NBLK. CACPROFUPNM>
ATMACCPROF=<ATMPORT_NBLK. ATMACCPROF>
ATMACCPROFNM=<ATMPORT_NBLK. ATMACCPROFNM>
CDVTPROF= <ATMPORT_NBLK. CDVTPROF>
CDVTPROFNM=<ATMPORT_NBLK. CDVTPROFNM>
NGCRWEIGHT=<ATMPORT_NBLK. NGCRWEIGHT>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>
Output Parameters
None.
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 41
A_ALA-A1000_SW4-7_ADD_ATM-PVCL-LTAdds an ATM Permanent Virtual Circuit (PVC) link on LT side.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.addATMPvclLt
Table 17: A_ALA-A1000_SW4-7_ADD_ATM-PVCL-LT
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
VCL_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
AID_VCL Access identifier for the ATM virtual channel link.
C R
VCL_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
VCL_RCV_TRAFDSC The traffic descriptor profile index for the receive direction.
1 to 310 S O
VCL_XMT_TRAFDSC
The transmit traffic descriptor profile index for the transmit direction.
1 to 310 S O
VCL_RCV_TRAFDSCNM
The traffic descriptor profile name for the receive direction.
S O
VCL_XMT_TRAFDSCNM
The traffic descriptor profile name for the transmit direction.
S O
Chapter 3: Atomic Service Description Layer (ASDL) Commands
42 Oracle Corporation
MML CommandsENT-VCL:<VCL_TID>:<AID_VCL>:<VCL_CTAG>::<VCL_RCV_TRAFDSC>,<VCL_XMT_TRAFDSC>, <VCL_RCV_TRAFDSCNM>,<VCL_XMT_TRAFDSCNM>:<VCL_NBLK>;
Where, AID_VCL will have the following format:
VPL in LT circuit:LTVCL-<AID_VCL.LTVCL.RACK>-<AID_VCL.LTVCL.SHELF>-
<AID_VCL.LTVCL.LT_SLOT>-<AID_VCL.LTVCL.CIRCUIT>-<AID_VCL.LTVCL.VPI>-
<AID_VCL.LTVCL.VCI>
Where, VCL_NBLK will contain one or more of the following named parameters separated by comma:
LINKTYPE=<VCL_NBLK.LINKTYPE> SEGENDPT=< VCL_NBLK.SEGENDPT>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message header><crxlf>
VCL_NBLK The ATM VCL parameter block containing one or more of the following named parameters with their values separated by commas:
LINKTYPESEGENDPT
C O
Table 17: A_ALA-A1000_SW4-7_ADD_ATM-PVCL-LT
Parameter Name Description RangeDefault Value
Type Class
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 43
M/s/s<ctag>/sCOMPLD<cr><lf>
^^^/* <command echo */ <crxlf>;
Output Parameters
None.
A_ALA-A1000_SW4-7_ADD_ATM-PVCL-NTAdds an ATM Permanent Virtual Circuit (PVC) link on NT side.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.addATMPvclNt
Table 18: A_ALA-A1000_SW4-7_ADD_ATM-PVCL-NT
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
VCL_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
AID_VCL Access identifier for the ATM virtual channel link.
C R
VCL_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
VCL_RCV_TRAFDSC The traffic descriptor profile index for the receive direction.
1 to 310 S O
VCL_XMT_TRAFDSC The transmit traffic descriptor profile index for the transmit direction.
1 to 310 S O
Chapter 3: Atomic Service Description Layer (ASDL) Commands
44 Oracle Corporation
MML CommandsENT-VCL:<VCL_TID>:<AID_VCL>:<VCL_CTAG>::<VCL_RCV_TRAFDSC>,<VCL_XMT_TRAFDSC>, <VCL_RCV_TRAFDSCNM>,<VCL_XMT_TRAFDSCNM>:<VCL_NBLK>;
Where, AID_VCL will have the following format: ? VCL in the NT:NTVCL-<AID_VCL.NTVCL.VPI>-< AID_VCL.NTVCL.VCI>
Where, VCL_NBLK will contain one or more of the following named parameters separated by comma:
LINKTYPE=<VCL_NBLK.LINKTYPE>
SEGENDPT=< VCL_NBLK.SEGENDPT>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
MAA<ctag>ADENY <crxlf> AAA/* <command echo */ <crxlf> (/s/s/w'<AID>:ERRCDE=<error code><cr><lf> (AAA/* error description */ <crxlf>)*)+;
If the command fails, the following error response will occur on the DSLAM:
Normal response<crxlfxlf>
VCL_RCV_TRAFDSCNM
The traffic descriptor profile name for the receive direction.
S O
VCL_XMT_TRAFDSCNM
The traffic descriptor profile name for the transmit direction.
S O
VCL_NBLK The ATM VCL parameter block containing one or more of the following named parameters with their values separated by commas:
LINKTYPESEGENDPT
C O
Table 18: A_ALA-A1000_SW4-7_ADD_ATM-PVCL-NT
Parameter Name Description RangeDefault Value
Type Class
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 45
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>;
Output Parameters
None.
A_ALA-A1000_SW4-7_ADD_ATM-PVPLAdds an ATM Private Virtual Path (PVP) link.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.addATMPvpl
Table 19: A_ALA-A1000_SW4-7_ADD_ATM-PVPL
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
VPL_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
AID_VPL Access identifier for the ATM virtual path link.
C R
VPL_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
VPL_RCV_TRAFDSC The traffic descriptor profile index for the receive direction.
1 to 310 S O
VPL_XMT_TRAFDSC The transmit traffic descriptor profile index for the transmit direction.
1 to 310 S O
Chapter 3: Atomic Service Description Layer (ASDL) Commands
46 Oracle Corporation
MML CommandsENT-VPL:<VPL_TID>:<AID_VPL>:<VPL_CTAG>::<VPL_RCV_TRAFDSC>,<VPL_XMT_TRAFDSC>, <VPL_RCV_TRAFDSCNM>,<VPL_XMT_TRAFDSCNM>:<VPL_NBLK>;
Where, AID_VPL can take one of the following values:
VPL in the NT:NTVPL-<AID_VPL.NTVPL.VPI>
VPL in a server:SERWPL-<AID_VPL.SERWPL.RACK>-<AID_VPL.SERWPL.SHELF>-<AID_VPL.SERWPL.SERV_SLOT>-<AID_VPL.SERWPL.CIRCUITX <AID_VPL.SERWPL.VPI>
VPL in an LT circuit:LTVPL-<AID_VPL.LTVPL. PACK>-<AID_VPL.LTVPL.SHELF>-
<AID_VPL.LTVPL.LT_SLOT>-<AID_VPL.LTVPL.CIRCUIT>-<AID_VPL.LTVPL.VPI>
VPL in an LT IMA group:LTIMAVPLXAID_VPL.LTIMAVPL. PACK>-<AID_VPL.LTIMAVPL.SHELF>-<AID_VPL.LTIMAVPL.LT_SLOT>-<AID_VPL.LTIMAVPL.IMAGRPX <AID_VPL.LTIMAVPL.VPI>
Where, VPLNBLK will contain one or more of the following named parameters separated by comma:
VPL_RCV_TRAFDSCNM The traffic descriptor profile name for the receive direction.
S O
VPL_XMT_TRAFDSCNM The traffic descriptor profile name for the transmit direction.
S O
VPL_NBLK The ATM VPL parameter block containing one or more of the following named parameters with their values separated by commas:
LINKTYPESEGENDPT
C O
Table 19: A_ALA-A1000_SW4-7_ADD_ATM-PVPL
Parameter Name Description RangeDefault Value
Type Class
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 47
LINKTYPE=<VPL_NBLK.LINKTYPE>
SEGENDPT=< VPL_NBLK.SEGENDPT>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
AAA/* <command echo */ <crxlf>;
Output Parameters
None.
Chapter 3: Atomic Service Description Layer (ASDL) Commands
48 Oracle Corporation
A_ALA-A1000_SW4-7_ADD_ATMACC-PROFILEAdds an ATM access profile.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.addATMAccProfile
Table 20: A_ALA-A1000_SW4-7_ADD_ATMACC-PROFILE
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
ATMACC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
ATMACC_PROFILE_I D The ATM access profile index.
1 to 50 S R
ATMACC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
ATMACC_PROFILE_ NAME
Uniquely identifies this profile within its scope.
A string, 1 to 32 characters long.
S R
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 49
MML CommandsENT-PROFILE-ATMACC:<ATMACC_TID>:<ATMACC_PROFILE_ID>:<ATMACC_CTAG>:: <ATMACC_PROFILE_NAME>:<ATMACC_NBLK>;
Where, the ATM Access Profile parameter block <ATMACC_NBLK > will contain one or more of the following named parameters separated by commas:
GFCMODE=<ATMACC_NBLK.GFCMODE>
MAXVPCS=<ATMACC_NBLK.MAXVPCS>
MAXVCCS=<ATMACC_NBLK.MAXVCCS>
VPIBITS=<ATMACC_NBLK.VPIBITS>
VCIBITS=<ATMACC_NBLK.VCIBITS >
POLICING=<ATMACC_NBLK.POLICING>
SVCMAXVPI=<ATMACC_NBLK.SVCMAXVPI>
SVCMINVCI=<ATMACC_NBLK.SVCMINVCI>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
ATMACC_NBLK The ATM Access Profile parameter block containing one or more of the following named parameters with their values separated by commas:
GFCMODEMAXVPCSMAXVCCSVPIBITSVCIBITSPOLICINGSVCMAXVPISVCMINVCI
C O
Table 20: A_ALA-A1000_SW4-7_ADD_ATMACC-PROFILE
Parameter Name Description RangeDefault Value
Type Class
Chapter 3: Atomic Service Description Layer (ASDL) Commands
50 Oracle Corporation
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>;
Output Parameters
None.
A_ALA-A1000_SW4-7_ADD_CAC-PROFILEAdds a Connection Admission Control (CAC) profile.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.addCacProfile
Table 21: A_ALA-A1000_SW4-7_ADD_CAC-PROFILE
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
CAC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
CAC_PROFILE_ID The numeric identifier of the profile.
1 to 50 S R
CAC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 51
CAC_PROFILE_NAM E Uniquely identifies this profile within its scope.
A string, 1 to 32 characters long.
S R
CACPROF_NBLK The ATM CAC Profile parameter block containing one or more of the following named parameters with their values separated by commas:
CBRMAXCONCBRBWSECFACCBRBUFSECFACUBRMAXCONUBRMCRSECFACRTVBRMAXCONRTVBRBWSECFARTVBRBUFSECFACRTVBRNGCRSECFACRTVBROVRBKFANRTVBRMAXCONNRTVBRBWSECFACNRTVBRBUFSE0CFACNRTVBRNGCRSECFACNRTVBRNGCRSECFACGFRMAXCONGFRBWSECFACGFRBUFSECFACFROVRBKFACAGRBWSECFACAGRGCRSECFAC
C O
Table 21: A_ALA-A1000_SW4-7_ADD_CAC-PROFILE
Parameter Name Description RangeDefault Value
Type Class
Chapter 3: Atomic Service Description Layer (ASDL) Commands
52 Oracle Corporation
MML CommandsENT-PROFILE-CAC:<CAC_TID>:<CAC_PROFILE_ID>:<CAC_CTAG>::<CAC_PROFILE_NAME>: <CACPROF_NBLK>;
Where, the ATM CAC Profile parameter block < CACPROF_NBLK > will contain one or more of the following named parameters separated by commas:
CBRMAXCON=<CACPROF_NBLK.CBRMAXCON> CBRBWSECFAC=<CACPROF_NBLK. CBRBWSECFAC> CBRBUFSECFAC= <CACPROF_NBLK. CBRBUFSECFAC> UBRMAXCON=<CACPROF_NBLK. UBRMAXCON> UBRMCRSECFAC=<CACPROF_NBLK. UBRMCRSECFAC> RTVBRMAXCON=<CACPROF_NBLK. RTVBRMAXCON> RTVBRBWSECFAC=<CACPROF_NBLK. RTVBRBWSECFAC> RTVBRBUFSECFAC=<CACPROF_NBLK. RTVBRBUFSECFAC> RTVBRNGCRSECFAC=<CACPROF_NBLK. RTVBRNGCRSECFAC> RTVBROVRBKFAC=<CACPROF_NBLK. RTVBROVRBKFAC> NRTVBRMAXCON=<CACPROF_NBLK. NRTVBRMAXCON> NRTVBRBWSECFAC=<CACPROF_NBLK. NRTVBRBWSECFAC> NRTVBRBUFSECFAC=<CACPROF_NBLK. NRTVBRBUFSECFAC> NRTVBRNGCRSECFAC=<CACPROF_NBLK. NRTVBRNGCRSECFAC> NRTVBROVRBKFAC=<CACPROF_NBLK. NRTVBROVRBKFAC> GFRMAXCON=<CACPROF_NBLK. GFRMAXCON > GFRBWSECFAC=<CACPROF_NBLK. GFRBWSECFAC> GFRBUFSECFAC=<CACPROF_NBLK. GFRBUFSECFAC> GFROVRBKFAC=<CACPROF_NBLK. GFROVRBKFAC> AGRBWSECFAC=<CACPROF_NBLK. AGRBWSECFAC> AGRGCRSECFAC=<CACPROF_NBLK. AGRGCRSECFAC>
If the command fails, the following error response will occur on the DSLAM:
Error response<cr><lf><lf>
^^^<message header><cr><lf>
M^^<ctag>^DENY <cr><lf>
^^^/* <command echo> */ <cr><lf>
(^^^"<AID>:ERRCDE=<error code><cr><lf>
(^^^/* error description */ <cr><lf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<cr><lf><lf>
AAA<message header><crxlf>
MAA<ctag>ACOMPLD<crXlf>
/-./¦.*./* <command echo */ <crxlf>;
Output Parameters
None.
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 53
A_ALA-A1000_SW4-7_ADD_CDVT-PROFILEAdds a Cell Delay Variation Tolerance (CDVT) profile.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.addCdvtProfile
Table 22: A_ALA-A1000_SW4-7_ADD_CDVT-PROFILE
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
CDVT_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
CDVT_PROFILE_ID The AT M cell delay variation tolerance profile index.
1 to 20 S R
CDVT_PROFILE_NA ME
Uniquely identifies this profile within its scope.
A string, 1 to 32 characters long.
S R
CDVT_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
Chapter 3: Atomic Service Description Layer (ASDL) Commands
54 Oracle Corporation
MML CommandsENT-PROFILE-CDVT:<CDVT_TID>:<CDVT_PROFILE_ID>:<CDVT_CTAG>::<CDVT_PROFILE_ NAME>:<CDVTPROF_NBLK>;
Where, the ATM CDVT Profile parameter block <CDVTPROF_NBLK> will contain one or more of the following named parameters separated by commas:
CDVTCBR=<CDVTPROF_NBLK. CDVTCBR>
CDVTRTVBR=<CDVTPROF_NBLK. CDVTRTVBR>
CDVTNRTVBR=<CDVTPROF_NBLK. CDVTNRTVBR>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
CDVTPROF_NBLK The ATM CDVT Profile parameter block containing one or more of the following named parameters with their values separated by commas:
CDVTCBRCDVTUBRCDVTRTVBRCDVTNRTVBRCDVTGFR
C O
Table 22: A_ALA-A1000_SW4-7_ADD_CDVT-PROFILE
Parameter Name Description RangeDefault Value
Type Class
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 55
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>;
Output Parameters
None.
A_ALA-A1000_SW4-7_ADD_CRS-VCAdds a virtual circuit cross connect.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.addCrsVc
Table 23: A_ALA-A1000_SW4-7_ADD_CRS-VC
Parameter Name
Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
VCCC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NT_VCL Access identifier for the ATM virtual channel link in the NT/Server.
C R
LT_VCL Access identifier for the ATM virtual channel link in the LT/Server.
C R
VCCC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
VCCC_PST The desired primary state to be set.
IS (In-Service)OOS (Out-Of-Service)
C O
Chapter 3: Atomic Service Description Layer (ASDL) Commands
56 Oracle Corporation
MML CommandsED-CRS-VC:<VCCC_TID>:<NT_VCL>,<LT_VCL>:<VCCC_CTAG>::::<VCCC_PST>;
Where, <NT_VCL> can take one of the following values:
VCL in the NT:NTVCL-<NT_VCL.NTVCL.VPI>-<NT_VCL.NTVCL.VCI>
VCL in the server:SERWCL-<NT_VCL.SERWCL.RACK>-<NT_VCL.SERWCL.SHELF>-<NT_VCL.SERWCL.SERV_SLOT>-<NT_VCL.SERWCL.CIRCUITX <NT_VCL.SERWCL.VPI>-<NT_VCL.SERWCL.VCI>
Where, <LT_VCL> can take one of the following values:
VCL in the server:SERWCL-<LT_VCL.SERWCL.RACK>-<LT_VCL.SERWCL.SHELF>-<LT_VCL.SERWCL.SERV_SLOT>-<LT_VCL.SERWCL.CIRCUITX <LT_VCL.SERWCL.VPI>-<LT_VCL.SERWCL.VCI>
For LT circuits:LTVCL-<LT_VCL.LTVCL.RACK>-<LT_VCL.LTVCL.SHELF>-<LT_VCL.LTVCL.LT_SLOT>-<LT_VCL.LTVCL.CIRCUIT>-<LT_VCL.LTVCL.VPI>-<LT_VCL.LTVCL.VCI>
For LT IMA groups:LTIMAVCL-<LT_VCL.LTIMAVCL.RACK>-<LT_VCL.LTIMAVCL.SHELF>-<LT_VCL.LTIMAVCL.LT_SLOT>-<LT_VCL.LTIMAVCL.IMAGRPX <LT_VCL.LTIMAVCL.VPI>-<LT_VCL.LTIMAVCL.VCI>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
MAA<ctag>ADENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>;
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 57
Output Parameters
None.
A_ALA-A1000_SW4-7_ADD_CRS-VPAdds a virtual path cross connect.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.addCrsVp
MML CommandsED-CRS-VP:<VPCC_TID>:<NT_VPL>, <LT_VPL>:<VPCC_CTAG>::::<VPCC_PST>;
Where, NT_VPL will have one of the following format:
VPL in NT:
Table 24: A_ALA-A1000_SW4-7_ADD_CRS-VP
Parameter Name
Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
VPCC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NT_VPL Access identifier for the ATM virtual path link in the NT.
C R
LT_VPL Access identifier for the ATM virtual path link in the LT/Server.
C R
VPCC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
VPCC_PST The desired primary state to be set.
IS (In-Service)OOS (Out-Of-Service)
S O
Chapter 3: Atomic Service Description Layer (ASDL) Commands
58 Oracle Corporation
NTVPL-<NT_VPL.NTVPL. VPI>
Where, LTVPL will have one of the following format:
VPL in the server:SERWPL-<LT_VPL.SERWPL.RACK>-<LT_VPL.SERWPL.SHELF>-<LT_VPL.SERWPL.SERV_SLOT>-<LT_VPL.SERWPL.CIRCUITX <LT_VPL.SERWPL.VPI>
LT circuits:LTVPL-<LT_VPL.LTVPL.RACK>-<LT_VPL.LTVPL.SHELF>-<LT_VPL.LTVPL.LT_SLOT>-<LT_VPL.LTVPL.CIRCUIT>-<LT_VPL.LTVPL.VPI>
LT IMA groups:LTIMAVPLXLT VPL.LTIMAVPL.RACK>-<LT_VPL.LTIMAVPL.SHELF>-<LT_VPL.LTIMAVPL.LT_SLOT>-<LT_VPL.LTIMAVPL.IMAGRPX <LT_VPL.LTIMAVPL.VPI>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>;
Output Parameters
None.
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 59
A_ALA-A1000_SW4-7_ADD_OC3-INTERFACEAdds an OC3 interface.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.IntProv.addOC3Interface
MML CommandsED-OC3:<OC3_TID>:<AID_OC3>:<OC3_CTAG>:::<OC3_NBLK>:<OC3_PST>;
Where, the access identifier <AID_OC3> for the OC3 facility can take one of the following values:
Table 25: A_ALA-A1000_SW4-7_ADD_OC3-INTERFACE
Parameter Name
Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
OC3_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
OC3_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
OC3_PST The desired primary state to be set.
IS (In-Service)OOS (Out-Of-Service)
S O
AID_OC3 Access identifier for the OC3 facility.
C R
OC3_NBLK OC3 facility parameter block containing the following named parameters with their values:
OPMODE
C O
Chapter 3: Atomic Service Description Layer (ASDL) Commands
60 Oracle Corporation
OC3 facility in the NT sides A & B:NTOC3
OC3 facility in the LT:LTOC3-<AID_OC3.LT0C3.RACK>-<AID_0C3.LT0C3.SHELF>-<AID_0C3.LT0C3.LT_SL0T>-<AID_0C3.LT0C3.CIRCUIT>
Where, the OC3 facility parameter block <OC3_NBLK> contains the following named parameter:
OPMODE=<OC3_NBLK.OPMODE>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
AAA/* <command echo */ <crxlf>
Output Parameters
None.
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 61
A_ALA-A1000_SW4-7_ADD_SHDSL-PARAMETERSAdds SHDSL parameters.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.DSLProv.addSHDSLParams
Table 26: A_ALA-A1000_SW4-7_ADD_SHDSL-PARAMETERS
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
SHDSL_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
SHDSL_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
SHDSL_NUM_REPEATERS
Number of repeaters provisioned for this SHDSL span.
S O
SHDSL_PST The desired primary state to be set.
IS (In-Service)OOS (Out-Of-Service)
S O
AID_SHDSL The access identifier for the SHDSL circuit.
C R
Chapter 3: Atomic Service Description Layer (ASDL) Commands
62 Oracle Corporation
MML CommandsENT-SHDSL:<SHDSL_TID>:<AID_SHDSL>:<SHDSL_CTAG>::<SHDSL_NUM_REPEATERS>: <SHDSL_NBLK>:<SHDSL_PST>;
Where, <AID_SHDSL> will have the following format:LTSHDSL--<AID_SHDSL.LTSHDSL.RACK>--<AID_SHDSL.LTSHDSL.SHELF>--<AID_SHDSL.LTSHDSL.LT_SLOT>--<AID_SHDSL.LTSHDSL.CIRCUIT>
Where, the SHDSL circuit parameter block <SHDSL_NBLK> will contain one or more of the following named parameters separated by commas :
PORTID=<SHDSL_NBLK.PORTID>
PSDTYPE=<SHDSL_NBLK.PSDTYPE>
WIREMODE=<SHDSL_NBLK.WIREMODE>
MINLINERATE=<SHDSL_NBLK.MINLINERATE>
MAXLINERATE=<SHDSL_NBLK.MAXLINERATE>
TARRMDNWC=<SHDSL_NBLK.TARRMDNWC>
TARRMDNCC=<SHDSL_NBLK.TARRMDNCC>
SHDSL_NBLK The SHDSL circuit parameter block containing one or more of the following named parameters with their values separated by commas:
PORTIDPSDTYPEWIREMODEMINLINERATEMAXLINERATETARRMDNWCTARRMDNCCTARRMUPWCTARRMUPCCREMOTEMGTREGIONCONFIMAGRP
C R
Table 26: A_ALA-A1000_SW4-7_ADD_SHDSL-PARAMETERS
Parameter Name Description RangeDefault Value
Type Class
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 63
TARRMUPWC=<SHDSL_NBLK.TARRMUPWO TARRMUPCC=<SHDSL_NBLK.TARRMUPCO REMOTEMGT=<SHDSL_NBLK.REMOTEMGT> REGIONCONF=<SHDSL_NBLK.REGIONCONF> IMAGRP=<SHDSL_NBLK.IMAGRP>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>
Output Parameters
None.
Chapter 3: Atomic Service Description Layer (ASDL) Commands
64 Oracle Corporation
A_ALA-A1000_SW4-7_ADD_SIG-CHANNELAdds a signalling channel.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.SVCProv.addSigChannel
Table 27: A_ALA-A1000_SW4-7_ADD_SIG-CHANNEL
Parameter Name
Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
SIGCHN_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
SIGCHN_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
SIGCHN_STATE The desired state to be set. S O
SIGCHN_VPI The VPI value associated with the signaling channel.
S O
SIGCHN_VCI The VCI value associated with the signaling channel.
S O
AID_SIGCHN Access identifier for the ATM signaling channel.
C R
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 65
MML CommandsENT-SIGCHN:<SIGCHN_TID>:<AID_SIGCHN>:<SIGCHN_CTAG>::<SIGCHN_VPI> <,SIGCHN_VCI>:<SIGCHN_NBLK>:<SIGCHN_STATE>;
Where, AID_SIGCHN can take one of the following values:
On NT side:NTSIGCHN
On the LT side:LTSIGCHN-<AID_SIGCHN.LTSIGCHN.RACK>-<AID_SIGCHN. LTSIGCHN.SHELF>-<AID_SIGCHN.LTSIGCHN.SLOT>-<AID_SIGCHN. LTSIGCHN.CIRCUIT>
IMA group:LTIMASIGCHN-<AID_SIGCHN.LTIMASIGCHN.RACK>-<AID_SIGCHN. LTIMASIGCHN.SHELF>-<AID_SIGCHN. LTIMASIGCHN.SLOT>-<AID_SIGCHN. LTIMASIGCHN.IMAGRP>
Where, the Signaling Channel parameter block SIGCHN_NBLK will contain one or more of the following named parameters separated by commas :
SIGCHN_NBLK The signaling channel parameter block containing one or more of the following named parameters with their values separated by commas:
XMITTRAFDSCRXMITTRAFDSCRNMRECVTRAFDSCRRECVTRAFDSCRNMMAXACTCALLSSAALPROFSAALPROFNMSAALMODEDSS2PROFDSS2PROFNMSIGPERFPROFSIGPERFPROFNMMULTIPOINTSEGENDPT
C R
Table 27: A_ALA-A1000_SW4-7_ADD_SIG-CHANNEL
Parameter Name
Description RangeDefault Value
Type Class
Chapter 3: Atomic Service Description Layer (ASDL) Commands
66 Oracle Corporation
XMITTRAFDSCR=<SIGCHN_NBLK. XMITTRAFDSCR>
XMITTRAFDSCRNM=<SIGCHN_NBLK. XMITTRAFDSCRNM> RECVTRAFDSCR=<SIGCHN_NBLK. RECVTRAFDSCR>
RECVTRAFDSCRNM=<SIGCHN_NBLK. RECVTRAFDSCRNM>
MAXACTCALLS=<SIGCHN_NBLK. MAXACTCALLS>
SAALPROF=<SIGCHN_NBLK. SAALPROF>
SAALPROFNM=<SIGCHN_NBLK. SAALPROFNM>
SAALMODE=<SIGCHN_NBLK. SAALMODE>
DSS2PROF=<SIGCHN_NBLK. DSS2PRO>
DSS2PROFNM=<SIGCHN_NBLK. DSS2PROFNM>
SIGPERFPROF=<SIGCHN_NBLK. SIGPERFPROF>
SIGPERFPROFNM=<SIGCHN_NBLK. SIGPERFPROFNM>
MULTIPOINT=<SIGCHN_NBLK. MULTIPOINT>
SEGENDPT=<SIGCHN_NBLK. SEGENDPT>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>
Output Parameters
None.
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 67
A_ALA-A1000_SW4-7_ADD_SIG-CHANNEL-PARAMSAdds signalling channel parameters.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.SVCProv.addSigChannelParams
Table 28: A_ALA-A1000_SW4-7_ADD_SIG-CHANNEL-PARAMS
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
SIGCHNP_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
SIGCHNP_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
SIGCHNP_STATE The desired state to be set. S O
AID_SIGCHN Access identifier for the ATM signaling channel.
C R
Chapter 3: Atomic Service Description Layer (ASDL) Commands
68 Oracle Corporation
MML CommandsED-SIGCHN:<SIGCHNP_TID>:<AID_SIGCHN>:<SIGCHNP_CTAG>:::<SIGCHN_NBLK>: <SIGCHNP_STATE>;
Where, AID_SIGCHN can take one of the following values:
On NT side:NTSIGCHN
On the LT side:LTSIGCHN-<AID_SIGCHN.LTSIGCHN.RACK>-<AID_SIGCHN. LTSIGCHN.SHELF>-<AID_SIGCHN.LTSIGCHN.SLOT>-<AID_SIGCHN.LTSIGCHN.CIRCUIT>
IMA group:LTIMASIGCHN-<AID_SIGCHN.LTIMASIGCHN.RACK>-<AID_SIGCHN. LTIMASIGCHN.SHELF>-<AID_SIGCHN. LTIMASIGCHN.SLOT>-<AID_SIGCHN. LTIMASIGCHN.IMAGRP>
Where, the Signaling Channel parameter block SIGCHN_NBLK will contain one or more of the following named parameters separated by commas:
MAXACTCALLS=<SIGCHN_NBLK. MAXACTCALLS>
SAALPROF=<SIGCHN_NBLK. SAALPROF>
SAALPROFNM=<SIGCHN_NBLK. SAALPROFNM>
SIGCHN_NBLK The signaling channel parameter block containing one or more of the following named parameters with their values separated by commas:
MAXACTCALLSSAALPROFSAALPROFNMSAALMODEDSS2PROFDSS2PROFNMSIGPERFPROFSIGPERFPROFNMMULTIPOINTSEGENDPT
C O
Table 28: A_ALA-A1000_SW4-7_ADD_SIG-CHANNEL-PARAMS
Parameter Name Description RangeDefault Value
Type Class
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 69
SAALMODE=<SIGCHN_NBLK. SAALMODE>
DSS2PR0F=<SIGCHN_NBLK. DSS2PR0F>
DSS2PR0FNM=<SIGCHN_NBLK. DSS2PR0FNM>
SIGPERFPROF=<SIGCHN_NBLK. SIGPERFPROF>
SIGPERFPROFNM=<SIGCHN_NBLK. SIGPERFPROFNM>
MULTIPOINT=<SIGCHN_NBLK. MULTIPOINT>
SEGENDPT=<SIGCHN_NBLK. SEGENDPT>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>
Output Parameters
None.
Chapter 3: Atomic Service Description Layer (ASDL) Commands
70 Oracle Corporation
A_ALA-A1000_SW4-7_ADD_SVC-USERAdds a Switched Virtual Circuit (SVC) user.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.SVCProv.addSVCUser
Table 29: A_ALA-A1000_SW4-7_ADD_SVC-USER
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
SVCUSERTID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
SVCUSERCTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
ATMADDRESS Access identifier for the SVC user.
S R
ATMPORT ATM port associated with the SVC user.
C R
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 71
MML CommandsENT-SVCUSR:<SVCUSER_TID>:<ATM_ADDRESS>:<SVCUSER_CTAG>::<ATM_PORT>: <SVCUSR NBLK>;
Where, ATM_PORT can take one of the following values:
On the LT side:LTATM-<ATM_PORT.LTATM.RACK>-<ATM_ PORT.LTATM.SHELF>-<ATM_ PORT.LTATM.SLOT>-<ATM_ PORT.LTATM.CIRCUIT>
IMA group:LTIMAATM-<ATM_ PORT.LTIMAATM.RACK>-< PORT.LTIMAATM.SHELF>-<ATM_ PORT.LTIMAATM.SLOT>-<ATM_ PORT.LTIMAATM.CIRCUIT>
Where, the SVC user parameter block SVCUSER_NBLK contains one or more of the following named parameters separated by commas:
CIC=<SVCUSER_NBLK.CIO
ALLOWCALLIN=<SVCUSER_NBLK. ALLOWCALLIN> ALLOWCALLOUT=<SVCUSER_NBLK. ALLOWCALLOUT> IDENTPROF=<SVCUSER_NBLK. IDENTPROF> IDENTPROFNM=<SVCUSER_NBLK. IDENTPROFNM>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
SVCUSERNBLK The SVC user parameter block containing one or more of the following named parameters with their values separated by commas:
CICALLOWCALLINALLOWCALLOUTIDENTPROFIDENTPROFNM
C R
Table 29: A_ALA-A1000_SW4-7_ADD_SVC-USER
Parameter Name Description RangeDefault Value
Type Class
Chapter 3: Atomic Service Description Layer (ASDL) Commands
72 Oracle Corporation
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>
Output Parameters
None.
A_ALA-A1000_SW4-7_ADD_T1DS1-INTERFACEAdds T1/DS1 interface.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.IntProv.addTlDSHnterface
Table 30: A_ALA-A1000_SW4-7_ADD_T1DS1-INTERFACE
Parameter Name
Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
DS1_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
DS1_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 73
MML CommandsENT-T1:<DS1_TID>:<AID_DS1>:<DS1_CTAG>:::<DS1_NBLK>:<DS1_PST>;
Where, the access identifier <AID_DS1> for the T1 (DS1) facility can take the following format:
LT circuit:LTT1-<AID_DS1.LTT1.RACK>-<AID_DS1.LTT1.SHELF>-<AID_DS1.LTT1.LT_SLOT>-<AID_DS1.LTT1.CIRCUIT>
Where, the DS1 facility parameter block <DS1_NBLK> will contain one or more of the following named parameters separated by commas:
PORTID=<DSl_NBLK.PORTID> LINETYPE=<DS1_NBLK.LINETYPE> LBO=<DSl_NBLK.LBO> EQLZ=<DS1_NBLK.EQLZ> IMAGRP=<DS1_NBLK.IMAGRP>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
DS1_PST The desired primary state to be set.
IN (In-Service)OOS (Out-Of-Service)
S O
AID_DS1 Access identifier for the T1 (DS1) facility.
C R
DS1_NBLK The DS1 facility parameter block containing one or more of the following named parameters with their values separated by commas:
PORTIDLINETYPELBOEQLZ
C R
Table 30: A_ALA-A1000_SW4-7_ADD_T1DS1-INTERFACE
Parameter Name
Description RangeDefault Value
Type Class
Chapter 3: Atomic Service Description Layer (ASDL) Commands
74 Oracle Corporation
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>
Output Parameters
None.
A_ALA-A1000_SW4-7_ADD_T3DS3-INTERFACEAdds T3/DS3 interface.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.IntProv.addT3DS3Interface
Table 31: A_ALA-A1000_SW4-7_ADD_T3DS3-INTERFACE
Parameter Name
Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
DS3_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
DS3_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.Default value: 0
S O
DS3_PST The desired primary state to be set.
IN (In-Service)OOS (Out-Of-Service)
S O
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 75
MML CommandsED-T3:<DS3_TID>:<AID_DS3>:<DS3_CTAG>:::<DS3_NBLK>:<DS3_PST>;
Where, the access identifier <AID_DS3> for the T3 (DS3) facility take the following format: ? DS3/T3 facility in the LT
LTT3-<AID_DS3.LTT3.RACK>-<AID_DS3.LTT3.SHELF>-<AID_DS3.LTT3.LT_SLOT>-<AID_DS3.LTT3.CIRCUIT>
Where, the DS1 facility parameter block <DS3_NBLK> will contain one or more of the following named parameters separated by commas :
CELLMAPNG=<DS3_NBLK.CELLMAPNG> CRDECPLNG=<DS3_NBLK.CRDECPLNG> OOFDETECT=<DS3_NBLK.OOFDETECT> LINEBLDOUT=<DS3_NBLK.LINEBLDOUT>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
AID_DS3 Access identifier for the T3 (DS3) facility.
C R
DS3_NBLK The DS3 facility parameter block containing one or more of the following named parameters with their values separated by commas:
CELLMAPNGCRDECPLNGOOFDETECTLINEBLDOUT
C O
Table 31: A_ALA-A1000_SW4-7_ADD_T3DS3-INTERFACE
Parameter Name
Description RangeDefault Value
Type Class
Chapter 3: Atomic Service Description Layer (ASDL) Commands
76 Oracle Corporation
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>
Output Parameters
None.
A_ALA-A1000_SW4-7_ADD_TRAFFDESC-PROFILEAdds traffic descriptor profile.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.addTraffDescProfile
Table 32: A_ALA-A1000_SW4-7_ADD_TRAFFDESC-PROFILE
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
TRAFDSC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
TRAFDSC_PROFILE_ ID The numeric identifier of the profile.
1 to 310 S R
TRAFDSC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 77
MML CommandsENT-PROFILE-TRAFDSC:<TRAFDSC_TID>:<TRAFDSC_PROFILE_ID>:<TRAFDSC_CTAG>:: <TRAFDSC_PROFILE_NAME>,,<TRAFDSC_TYPE>:<TRAFDSC_NBLK>;
Where, the ATM Traffic Descriptor profile parameter block <TRAFDSC_NBLK> will contain one or more of the following named parameters separated by commas:
FRAMEDSC=<TRAFDSC_NBLK.FRAMEDESC>
If (TRAFDSC_TYPE== CBR ) { CLP1PCR=<TRAFDSC_NBLK. CLP1PCR> CDVT=<TRAFDSC_NBLK.CDVT> }
IF(TRAFDESC_TYPE==UBR) {
TRAFDSC_PROFILE_ NAME
Uniquely identifies this profile within its scope.
A string, 1 to 32 characters long.
S R
TRAFDSC_TYPE Traffic descriptor service category type.
S O
TRAFDSC_NBLK The ATM traffic descriptor profile parameter block containing one or more of the following named parameters with their values separated by commas:
FRAMEDSCCLP1PCRCDVTCLP1MCRCLP1SCRMBSCLP0SCRMFS
These values are added to MML based on parameter TRAFDSC_TYPE value.
C R
Table 32: A_ALA-A1000_SW4-7_ADD_TRAFFDESC-PROFILE
Parameter Name Description RangeDefault Value
Type Class
Chapter 3: Atomic Service Description Layer (ASDL) Commands
78 Oracle Corporation
CLP1PCR=<TRAFDSC_NBLK. CLP1PCR> CLP1MCR=<TRAFDSC_NBLK. CLP1MCR> }
IF(TRAFDESC_TYPE== VBR1RT || TRAFDESC_TYPE== VBR1NRT) {
CLP1PCR=<TRAFDSC_NBLK. CLP1PCR>
CLP1SCR=<TRAFDSC_NBLK. CLP1SCR>
MBS = <TRAFDSC_NBLK.MBS>
CDVT=<TRAFDSC_NBLK.CDVT>
}
IF (TRAFDESC_TYPE== VBR2NRT || TRAFDESC_TYPE== VBR3NRT) {
CLP1PCR=<TRAFDSC_NBLK. CLP1PCR>
CLPOSCR=<TRAFDSC_NBLK. CLPOSCR>
MBS=<TRAFDSC_NBLK.MBS>
CDVT=<TRAFDSC_NBLK.CDVT>
}
IF (TRAFDESC_TYPE== GFR1 || TRAFDESC_TYPE== GFR2) {
CLP1PCR=<TRAFDSC_NBLK. CLP1PCR>
CLP1MCR=<TRAFDSC_NBLK. CLP1MCR>
MBS=<TRAFDSC_NBLK.MBS>
CDVT=<TRAFDSC_NBLK.CDVT>
MFS=<TRAFDSC_NBLK.MFS>
}
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(^^^/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
AAA/* <command echo */ <crxlf>;
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 79
Output Parameters
None.
A_ALA-A1000_SW4-7_ADD_XDSL-PORTAdds an XDSL port.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.DSLProv.addXDSLPort
Table 33: A_ALA-A1000_SW4-7_ADD_XDSL-PORT
Parameter Name
Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
XDSL_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.Default value: NULL
S O
XDSL_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
XDSL_PST The desired primary state to be set.
IN (In-Service)OOS (Out-Of-Service)
S O
AID_XDSL Access identifier for the ADSL line.
C R
Chapter 3: Atomic Service Description Layer (ASDL) Commands
80 Oracle Corporation
MML CommandsED-XDSL:[tid]:aid_xdsl:[ctag]:::[xdsl_nblk]:[pst];
Where, access identifier for ADSL lines <AID_XDSL> is:XDSL-rack-shelf-lt_slot-circuit
Where, the named parameter block for ADSL <ADSL_NBLK> will contain one or more of the following named parameters separated by commas:
PORTID=<XDSL_NBLK.PORTID> XSRVCPROFNM=< XDSL_NBLK. ASRVCPROFNM > XSRVCPROFID=< XDSL_NBLK. ASRVCPROFNM > XLNEPROFNM=< XDSL_NBLK. ALNEPROFNM > XLNEPROFID=< XDSL_NBLK. ALNEPROFNM > OPMASKA=< XDSL_NBLK. OPMASKA > OPMASKA2=< XDSL_NBLK. OPMASKA2 > OPMASKV=< XDSL_NBLK. OPMASKV > OPMASKA2M=< XDSL_NBLK. OPMASKA2M > BONDMODTYPE = <XDSL_NBLK.BONDMODTYPE>
If the command fails, the following error response will occur on the DSLAM:
Normal responsesid yy-mm-dd hh:mm:ss
M c COMPLD
/* ED-XDSL:[tid]:aid_xdsl:[ctag]:::[xdsl_nblk]:[pst] */
;
XDSL_NBLK The ADSL line parameter block containing one or more of the following named parameters with their values separated by commas:
PORTIDXSRVCROFNMXSRVCPROFIDXLNEROFNMXLNEPROFIDOPMASKAOPMASKA2OPMASKVOPMASKA2MBONDMODTYPE
C O
Table 33: A_ALA-A1000_SW4-7_ADD_XDSL-PORT
Parameter Name
Description RangeDefault Value
Type Class
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 81
Error responsesid yy-mm-dd hh:mm:ssM c DENY
/* ED-XDSL:[tid]:aid_xdsl:[ctag]:::[xdsl_nblk]:[pst] */
errcde
;
Output Parameters
None.
A_ALA-A1000_SW4-7_DEACT_CRS-VCDeactivates a virtual circuit cross connect.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.deactCrsVc
Table 34: A_ALA-A1000_SW4-7_DEACT_CRS-VC
Parameter Name
Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
VCCC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
VCCC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
NT_VCL Access identifier for the ATM virtual channel link in the NT/Server.
C R
LT_VCL Access identifier for the ATM virtual channel link in the LT/Server.
C R
Chapter 3: Atomic Service Description Layer (ASDL) Commands
82 Oracle Corporation
MML CommandsENT-CRS-VC:<VCCC_TID>: NTVCL-<NT_VCL.VPI>-<NT_VCL.VCI >, LTVCL-
<LT_VCL.LTVCL.RACK>-< LT_VCL.LTVCL.SHELF>-<LT_VCL.LTVCL.LTSLOT>-<
LT_VCL.LTVCL.CIRCUIT>-< LT_VCL.LTVCL.VPI>-<LT_VCL.LTVCL.VCI>:<
VCCC_CTAG>::::OOS;
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>;
Output Parameters
None.
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 83
A_ALA-A1000_SW4-7_DEACT_CRS-VPDeactivates a virtual path cross connect.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.deactCrsVp
MML CommandsENT-CRS-VP:<VPCC_TID>:<NT_VPL>,<LT_VPL>:<VPCC_CTAG>::::OOS;
Where, NT_VPL will have the following format:
VPL in NT:NTVPL-<NT_VPL.NTVPL.VPI>
Where, LTVPL will have one of the following format:
VPL in the server:
Table 35: A_ALA-A1000_SW4-7_DEACT_CRS-VP
Parameter Name
Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
VPCC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NT_VPL Access identifier for the ATM virtual path link in the NT.
C R
LT_VPL Access identifier for the ATM virtual path link in the LT/Server.
C R
VPCC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
Chapter 3: Atomic Service Description Layer (ASDL) Commands
84 Oracle Corporation
SERWPL-<LT_VPL.SERWPL.RACK>-<LT_VPL.SERWPL.SHELF >-<LT_VPL.SERWPL.SERV_SLOT>-<LT_VPL.SERWPL.CIRCUIT>-<LT VPL.SERWPL.VPI>
LT circuits:LTVPL-<LT_VPL.LTVPL.RACK>-<LT_VPL.LTVPL.SHELF>-<LT_VPL.LTVPL.LT_SLOT>-<LT_VPL.LTVPL.CIRCUIT>-<LT_VPL.LTVPL.VPI>
LT IMA groups:LTIMAVPLXLT_VPL.LTIMAVPL.RACK>-<LT_VPL.LTIMAVPL.SHELF>-<LT_VPL.LTIMAVPL.LT_SLOT>-<LT_VPL.LTIMAVPL.IMAGRPX <LT_VPL.LTIMAVPL.VPI>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
/-./¦.*./* <command echo */ <crxlf>;
Output Parameters
None.
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 85
A_ALA-A1000_SW4-7_DEL_ADSL-PORTDeletes a ADSL port.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.DSLProv.delDSLPort
MML CommandsFREE-PORT:<ADSLP_TID>: <PORT_AID>:< ADSLP_CTAG>[:];
Where, access identifier for port <PORT_AID> is:ADSL - <PORT_AID.RACK>-<PORT_AID.SHELF>- <PORT_AID.SLOT>-<PORT_AID.CIRCUIT>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
Table 36: A_ALA-A1000_SW4-7_DEL_ADSL-PORT
Parameter Name
Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
ADSLP_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
ADSLP_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
PORT_AID The AID for the user port. C R
Chapter 3: Atomic Service Description Layer (ASDL) Commands
86 Oracle Corporation
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
AAA/* <command echo */ <crxlf>
Output Parameters
None.
A_ALA-A1000_SW4-7_DEL_ATM-PVCL-LTDeletes an ATM Permanent Virtual Circuit (PVC) link from the line side.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.delATMPvclLt
MML CommandsDLT- VCL:<VCL_TID>:<AID_VCL>:<VCL_CTAG>[:];
Table 37: A_ALA-A1000_SW4-7_DEL_ATM-PVCL-LT
Parameter Name
Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
VCL_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
AID_VCL Access identifier for the ATM virtual channel link.
C R
VCL_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 87
Where, AID_VCL will have the following format: ? VPL in LT circuit:LTVCL-<AID_VCL.LTVCL.RACK>-<AID_VCL.LTVCL.SHELF>-
<AID_VCL.LTVCL.LT_SLOT>-<AID_VCL.LTVCL.CIRCUIT>-<AID_VCL.LTVCL.VPI>-<
AID_VCL.LTVCL.VCI>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>;
Output Parameters
None.
Chapter 3: Atomic Service Description Layer (ASDL) Commands
88 Oracle Corporation
A_ALA-A1000_SW4-7_DEL_ATM-PVCL-NTDeletes an ATM Permanent Virtual Circuit (PVC) link from the network side. It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.delATMPvclNt
MML CommandsDLT- VCL:<VCL_TID>:<AID_VCL>:<VCL_CTAG>[:];
Where, AID_VCL will have the following format: ? VCL in the NT:NTVCL-< AID_VCL.NTVCL.VPI>-< AID_VCL.NTVCL.VCI>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
Table 38: A_ALA-A1000_SW4-7_DEL_ATM-PVCL-NT
Parameter Name
Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
VCL_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
AID_VCL Access identifier for the ATM virtual channel link.
C R
VCL_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 89
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>;
Output Parameters
None.
A_ALA-A1000_SW4-7_DEL_ATM-PVPLDeletes an ATM Private Virtual Path (PVP) link.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.delATMPvpl
MML CommandsDLT-VPL:<VPL_TID>:<AID_VPL>:[VPL_CTAG][:];
Table 39: A_ALA-A1000_SW4-7_DEL_ATM-PVPL
Parameter Name
Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
VPL_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
AID_VPL Access identifier for the ATM virtual path link.
C R
VPL_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
Chapter 3: Atomic Service Description Layer (ASDL) Commands
90 Oracle Corporation
Where, AID_VPL can take one of the following values:
VPL in the NT:NTVPL-<AID_VPL.NTVPL.VPI>
VPL in a server:SERWPL-<AID_VPL.SERWPL.RACK>-<AID_VPL.SERWPL.SHELF>-<AID VPL.SERWPL.SERVJ3LOT>-<AID_VPL.SERWPL.CIRCUIT>-<AID_VPL.SERWPL.VPI>
VPL in an LT circuit:LTVPL-<AID_VPL.LTVPL.RACK>-<AID_VPL.LTVPL.SHELF>-
<AID_VPL.LTVPL.LT_SLOT>-<AID_VPL.LTVPL.CIRCUIT>-<AID_VPL.LTVPL.VPI>
VPL in an LT IMA group:LTIMAVPLXAID_VPL.LTIMAVPL.RACK>-<AID_VPL.LTIMAVPL.SHELF>-<AID_VPL.LTIMAVPL.LT_SLOT>-<AID_VPL.LTIMAVPL.IMAGRPX <AID_VPL.LTIMAVPL.VPI>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
/-./¦.*./* <command echo */ <crxlf>;
Output Parameters
None.
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 91
A_ALA-A1000_SW4-7_DEL_ATMACC-PROFILEDeletes an ATM access profile.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.delATMAccProfile
MML CommandsDLT-PROFILE-ATMACC:<ATMACC_TID>:<ATMACC_PROFILE_ID>:<ATMACC_CTAG>[:];
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
Table 40: A_ALA-A1000_SW4-7_DEL_ATMACC-PROFILE
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier.
S R
ATMACC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
ATMACC_PROFILE_ID The ATM access profile index.
1 to 50 S R
ATMACC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
Chapter 3: Atomic Service Description Layer (ASDL) Commands
92 Oracle Corporation
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
AAA/* <command echo */ <crxlf>;
Output Parameters
None.
A_ALA-A1000_SW4-7_DEL_CAC-PROFILEDeletes a Connection Admission Control (CAC) profile.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.delCacProfile
Table 41: A_ALA-A1000_SW4-7_DEL_CAC-PROFILE
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
CAC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
CAC_PROFILE_ID The numeric identifier of the profile.
1 to 50 S R
CAC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 93
MML CommandsDLT-PROFILE-CAC:<CAC_TID>:<CAC_PROFILE_ID>:<CAC_CTAG>[:];
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
MAA<ctag>ADENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message header><crxlf>
M/s/s<ctag>/sCOMPLD<cr><lf>
^^^/* <command echo */ <crxlf>;
Output Parameters
None.
Chapter 3: Atomic Service Description Layer (ASDL) Commands
94 Oracle Corporation
A_ALA-A1000_SW4-7_DEL_CDVT-PROFILEDeletes a Cell Delay Variance Tollerance (CDVT) profile. It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.delCdvtProfile
MML CommandsDLT-PROFILE-CDVT:<CDVT_TID>:<CDVT_PROFILE_IDXCDVT_CTAG>[:];
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
MAA<ctag>ADENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Table 42: A_ALA-A1000_SW4-7_DEL_CDVT-PROFILE
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
CDVT_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
CDVT_PROFILE_ID The AT M cell delay variation tolerance profile index.
1 to 20 S R
CDVT_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 95
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>;
Output Parameters
None.
A_ALA-A1000_SW4-7_DEL_CRS-VCDeletes a virtual circuit cross connect.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.delCrsVc
Table 43: A_ALA-A1000_SW4-7_DEL_CRS-VC
Parameter Name
Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
VCCC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NT_VCL Access identifier for the ATM virtual channel link in the NT/Server.
C R
LT_VCL Access identifier for the ATM virtual channel link in the LT/Server.
C R
VCCC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
Chapter 3: Atomic Service Description Layer (ASDL) Commands
96 Oracle Corporation
MML CommandsDLT-CRS-VC:<VCCC_TID>: NTVCL-< NT_VCL.VPI>-< NT_VCL.VCI >, LTVCL-<LT_VCL.LTVCL.RACK>-< LT_VCL.LTVCL.SHELF>-< LT_VCL.LTVCL.LTSLOTX <LT_VCL.LTVCL.CIRCUIT>-< LT_VCL.LTVCL.VPI>-<LT_VCL.LTVCL.VCI>: <VCCC_CTAG>[:];
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>;
Output Parameters
None.
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 97
A_ALA-A1000_SW4-7_DEL_CRS-VPDeletes a virtual path cross connect.
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.delCrsVp
MML CommandsDLT-CRS-VP:<VPCC_TID>:<NT_VPL>, <LT_VPL>:<VPCC_CTAG>[:];
Where, NT_VPL will have one of the following format:
VPL in NT:NTVPL-<NT_VPL.NTVPL.VPI>
Where, LTVPL will have one of the following format:
VPL in the server:SERWPL-<LT_VPL.SERWPL.RACK>-<LT_VPL.SERWPL.SHELF >-<LT_VPL.SERWPL.SERV_SLOT>-<LT_VPL.SERWPL.CIRCUITX <LT_VPL.SERWPL.VPI>
Table 44: A_ALA-A1000_SW4-7_DEL_CRS-VP
Parameter Name
Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
VPCC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NT_VPL Access identifier for the ATM virtual path link in the NT.
C R
LT_VPL Access identifier for the ATM virtual path link in the LT/Server.
C R
VPCC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
Chapter 3: Atomic Service Description Layer (ASDL) Commands
98 Oracle Corporation
LT circuits:LTVPL-<LT_VPL.LTVPL.RACK>-<LT_VPL.LTVPL.SHELF>-<LT_VPL.LTVPL.LT_SLOT>-<LT_VPL.LTVPL.CIRCUIT>-<LT_VPL.LTVPL.VPI>
LT IMA groups:LTIMAVPLXLT VPL.LTIMAVPL.RACK>-<LT_VPL.LTIMAVPL.SHELF>-<LT_VPL.LTIMAVPL.LT_SLOT>-<LT_VPL.LTIMAVPL.IMAGRPX <LT_VPL.LTIMAVPL.VPI>
Error response<crxlfxlf>
AAA<message header><crxlf>
MAA<ctag>ADENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command fails, the following error response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
/-./¦.*./* <command echo */ <crxlf>;
Output Parameters
None.
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 99
A_ALA-A1000_SW4-7_DEL_DSL-PROFILEDeletes a DSL profile.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.DSLProv.delDSLProfile
MML CommandsDLT-PROFILE-ADSL:<ADSLDLT_TID>:<ADSLDLT_PROFILE_ID>:<ADSLDLT_CTAG>[:];
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
MAA<ctag>ADENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Table 45: A_ALA-A1000_SW4-7_DEL_DSL-PROFILE
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
ADSLDLT_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
ADSLDLT_PROFILE_ ID
The ADSL profile index. 1 to 40 S R
ADSLDLT_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
Chapter 3: Atomic Service Description Layer (ASDL) Commands
100 Oracle Corporation
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>
Output Parameters
None.
A_ALA-A1000_SW4-7_DEL_SIG-CHANNELDeletes a signalling channel.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.SVCProv.delSigChannel
MML CommandsDLT-SIGCHN:<SIGCHN_TID>:<AID_SIGCHN>:<SIGCHN_CTAG>[:];
Table 46: A_ALA-A1000_SW4-7_DEL_SIG-CHANNEL
Parameter Name
Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
SIGCHN_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
SIGCHN_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
AID_SIGCHN Access identifier for the ATM signaling channel.
C R
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 101
Where, AID_SIGCHN can take one of the following values:
On NT side:NTSIGCHN
On the LT side:LTSIGCHN-<AID_SIGCHN.LTSIGCHN.RACK>-<AID_SIGCHN. LTSIGCHN.SHELF>-<AID_SIGCHN. LTSIGCHN.SLOT>-<AID_SIGCHN. LTSIGCHN.CIRCUIT>
IMA group:LTIMASIGCHN-<AID_SIGCHN.LTIMASIGCHN.RACK>-<AID_SIGCHN. LTIMASIGCHN.SHELF>-<AID_SIGCHN. LTIMASIGCHN.SLOT>-<AID_SIGCHN. LTIMASIGCHN.IMAGRP>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>
Output Parameters
None.
Chapter 3: Atomic Service Description Layer (ASDL) Commands
102 Oracle Corporation
A_ALA-A1000_SW4-7_DEL_SVC-USERDeletes a Switched Virtual Circuit (SVC) user. It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.SVCProv.delSVCUser
MML CommandsDLT-SVCUSR:<SVCUSER_TID>:<ATM_ADDRESS>:<SVCUSER_CTAG>[:];
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Table 47: A_ALA-A1000_SW4-7_DEL_SVC-USER
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
SVCUSER_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.Default value: NULL
S O
SVCUSER_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
ATM_ADDRESS Access identifier for the SVC User.
S R
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 103
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>
Output Parameters
None.
A_ALA-A1000_SW4-7_DEL_TRAFFDESC-PROFILEDeletes a traffic descriptor profile.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.ATMProv.delTraffDescProfile
MML CommandsDLT-PROFILE-TRAFDSC:<TRAFDSC_TID>:<TRAFDSC_PROFILE_ID>:<TRAFDSC_CTAG>[:];
If the command fails, the following error response will occur on the DSLAM:
Table 48: A_ALA-A1000_SW4-7_DEL_TRAFFDESC-PROFILE
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
TRAFDSC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.Default value: NULL
S O
TRAFDSC_PROFILE_ ID
The numeric identifier of the profile.
1 to 310 S R
TRAFDSC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.Default value: 0
S O
Chapter 3: Atomic Service Description Layer (ASDL) Commands
104 Oracle Corporation
Error response<crxlfxlf>
AAA<message header><crxlf>
MAA<ctag>ADENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>
Output Parameters
None.
A_ALA-A1000_SW4-7_DEL_XDSL-PORTDeletes an XDSL port.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.DSLProv.delXDSLPort
Table 49: A_ALA-A1000_SW4-7_DEL_XDSL-PORT
Parameter Name
Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
XDSL_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.Default value: NULL
S O
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 105
MML CommandsFREE-PORT:<XDSL_TID>: <PORT_AID>:< XDSL_CTAG>[:];
Where, access identifier for port <PORT_AID> is:XDSL - <PORT_AID.RACK>-<PORT_AID.SHELF>- <PORT_AID.SLOT>-<PORT_AID.CIRCUIT>
If the command fails, the following error response will occur on the DSLAM:
Error responsesid yy-mm-dd hh:mm:ss
M c DENY
/* FREE-PORT:[tid]:port_aid:[ctag][:] */
aid:ERRCDE=errcde
/* error description */
;
If the command succeeds, the following response will occur on the DSLAM:
Normal responsesid yy-mm-dd hh:mm:ss
M c COMPLD
/* FREE-PORT:[tid]:port_aid:[ctag][:] */
;
Output Parameters
None.
XDSL_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
PORT_AID The AID for the user port. C R
Table 49: A_ALA-A1000_SW4-7_DEL_XDSL-PORT
Parameter Name
Description RangeDefault Value
Type Class
Chapter 3: Atomic Service Description Layer (ASDL) Commands
106 Oracle Corporation
A_ALA-A1000_SW4-7_MOD_SHDSL-PARAMETERSModifies SHDSL parameters.
It is implemented by the following Java method:
com.metasolv.cartridge.oss.ala_dslam.prov.DSLProv.modSHDSLParams
Table 50: A_ALA-A1000_SW4-7_MOD_SHDSL-PARAMETERS
Parameter Name Description RangeDefault Value
Type Class
MCLI Host NE identifier. S R
SHDSL_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
SHDSL_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
SHDSL_NUM_REPEATERS
Number of repeaters provisioned for this SHDSL span.
S O
SHDSL_PST The desired primary state to be set.
IN (In-Service)OOS (Out-Of-Service)
S O
AID_SHDSL The access identifier for the SHDSL circuit.
C R
ASDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 107
MML CommandsED-SHDSL:<SHDSL_TID>:<AID_SHDSL>:<SHDSL_CTAG>::<SHDSL_NUM_REPEATERS>: <SHDSL_NBLK>:<SHDSL_PST>;
Where, the AID SHDSL will have the following format:LTSHDSL—<AID_SHDSL.RACK>—<AID_SHDSL.SHELF>—<AID_SHDSL.LT_SLOT>— AID_SHDSL.CIRCUIT>
Where, the SHDSL circuit parameter <SHDSL_NBLK> block will contain one or more of the following named parameters separated by commas:
PORTID=<SHDSL_NBLK.PORTID> PSDTYPE=<SHDSL_NBLK.PSDTYPE> WIREMODE=<SHDSL_NBLK.WIREMODE> MINLINERATE=<SHDSL_NBLK.MINLINERATE> MAXLINERATE=<SHDSL_NBLK.MAXLINERATE> TARRMDNWC=<SHDSL_NBLK.TARRMDNWO TARRMDNCC=<SHDSL_NBLK.TARRMDNCO TARRMUPWC=<SHDSL_NBLK.TARRMUPWO TARRMUPCC=<SHDSL_NBLK.TARRMUPCO REMOTEMGT=<SHDSL_NBLK.REMOTEMGT> REGIONCONF=<SHDSL_NBLK.REGIONCONF> IMAGRP=<SHDSL_NBLK.IMAGRP>
If the command fails, the following error response will occur on the DSLAM:
Error response<crxlfxlf>
SHDSL_NBLK The SHDSL circuit parameter block containing one or more of the following named parameters with their values separated by commas:
PORTIDPSDTYPEWIREMODEMINLINERATEMAXLINERATETARRMDNWCTARRMDNCCTARRMUPWCTARRMUPCCREMOTEMGTREGIONCONFIMAGRP
C O
Table 50: A_ALA-A1000_SW4-7_MOD_SHDSL-PARAMETERS
Parameter Name Description RangeDefault Value
Type Class
Chapter 3: Atomic Service Description Layer (ASDL) Commands
108 Oracle Corporation
AAA<message header><crxlf>
M/S/S<ctag>/SDENY <crxlf>
AAA/* <command echo */ <crxlf>
(/s/s/w'<AID>:ERRCDE=<error code><cr><lf>
(AAA/* error description */ <crxlf>)*)+;
If the command succeeds, the following response will occur on the DSLAM:
Normal response<crxlfxlf>
AAA<message headerxcrxlf>
M/s/s<ctag>/sCOMPLD<crXlf>
^^^/* <command echo */ <crxlf>
Output Parameters
None.
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 109
4
Service Definition
The Alcatel A1000 DSLAM cartridge contains a set of CSDLs that map to one or more ASDL commands. You can also create additional CSDLs that map to existing and newly-created ASDLs. An upstream system can assemble any of these CSDL commands onto a work order for provisioning.
This chapter presents detailed information on the CSDL parameters that we provide in this cartridge. The following table lists and describes the type of parameter information that is included.
Table 51: ASDL parameter information
Item Description
Parameter Name Identifies the parameter that is configured for the stated service.
Description Describes the parameter.
Range Describes or lists the range of values that can be used to satisfy this parameter.
Default Value Configures a default value for the parameter so that it is not mandatory for the upstream system to provide a value.
Chapter 4: Service Definition
110 Oracle Corporation
For a detailed description of the Required and Optional parameter classifications, refer to the ASAP Administration Guide.
Type Indicates one of the following parameter types:
S—Scalar, specifies the parameter label transmitted on the ASDL command. Scalar parameters are conventional name-value pair parameters.C—Compound, specifies the base name of the compound parameter transmitted on the ASDL command. A compound parameter contains structures or arrays of information that are represented by a particular structure name or compound parameter name. Each compound parameter can contain a large number of elements. If you use compound parameters, you only require a single entry in the ASAP translation tables to call the compound parameter and all its associated parameter elements.I—Indexed, identifies a parameter that contains a sequential numerical index value to tell the SARM that it should execute the same operation (for example, an ASDL command) for all occurrences of that index. Consequently, if there are several options on a particular CSDL command (OPT1, OPT2, OPT3, etc.), you can specify the OPT parameter as an indexed parameter. When you specify the OPT parameter as an indexed parameter, the SARM generates several occurrences of that same ASDL command and each command has a different value for the option being transmitted to the NEP.
For more information on parameter types, refer to the ASAP Developer Reference.
Class Indicates one of the following parameter classifications:
R—Required scalar parameterO—Optional scalar parameterC—Required compound parameterN—Optional compound parameterM—Mandatory indexed parameterI—Optional indexed parameterS—Parameter count
Table 51: ASDL parameter information
Item Description
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 111
CSDL commandsThis cartridge provides the following CSDL Commands:
C_ALA-A1000_SW4-7_ACT_ADSL-PROFILEC_ALA-A1000_SW4-7_ACT_CRS-VCC_ALA-A1000_SW4-7_ACT_CRS-VPC_ALA-A1000_SW4-7_ADD_ADSL-COMMON-PROFILEC_ALA-A1000_SW4-7_ADD_ADSL-DMT-PROFILEC_ALA-A1000_SW4-7_ADD_ADSL-DOWNSTREAM-PROFILEC_ALA-A1000_SW4-7_ADD_ADSL-LINE-PROFILEC_ALA-A1000_SW4-7_ADD_ADSL-PORTC_ALA-A1000_SW4-7_ADD_ADSL-PROFILEC_ALA-A1000_SW4-7_ADD_ADSL-UPSTREAM-PROFILEC_ALA-A1000_SW4-7_ADD_ATM-PORTC_ALA-A1000_SW4-7_ADD_ATM-PVCL-LTC_ALA-A1000_SW4-7_ADD_ATM-PVCL-NTC_ALA-A1000_SW4-7_ADD_ATM-PVPLC_ALA-A1000_SW4-7_ADD_ATMACC-PROFILEC_ALA-A1000_SW4-7_ADD_CAC-PROFILEC_ALA-A1000_SW4-7_ADD_CDVT-PROFILEC_ALA-A1000_SW4-7_ADD_CRS-VCC_ALA-A1000_SW4-7_ADD_CRS-VPC_ALA-A1000_SW4-7_ADD_OC3-INTERFACEC_ALA-A1000_SW4-7_ADD_SHDSL-PARAMETERSC_ALA-A1000_SW4-7_ADD_SIG-CHANNELC_ALA-A1000_SW4-7_ADD_SIG-CHANNEL-PARAMSC_ALA-A1000_SW4-7_ADD_SVC-USERC_ALA-A1000_SW4-7_ADD_T1DS1-INTERFACEC_ALA-A1000_SW4-7_ADD_T3DS3-INTERFACEC_ALA-A1000_SW4-7_ADD_TRAFFDESC-PROFILEC_ALA-A1000_SW4-7_ADD_XDSL-PORTC_ALA-A1000_SW4-7_DEACT_CRS-VCC_ALA-A1000_SW4-7_DEACT_CRS-VPC_ALA-A1000_SW4-7_DEL_ADSL-PORTC_ALA-A1000_SW4-7_DEL_ATM-PVCL-LTC_ALA-A1000_SW4-7_DEL_ATM-PVCL-NT
Chapter 4: Service Definition
112 Oracle Corporation
C_ALA-A1000_SW4-7_DEL_ATM-PVPLC_ALA-A1000_SW4-7_DEL_ATMACC-PROFILEC_ALA-A1000_SW4-7_DEL_CAC-PROFILEC_ALA-A1000_SW4-7_DEL_CDVT-PROFILEC_ALA-A1000_SW4-7_DEL_CRS-VCC_ALA-A1000_SW4-7_DEL_CRS-VPC_ALA-A1000_SW4-7_DEL_DSL-PROFILEC_ALA-A1000_SW4-7_DEL_SIG-CHANNELC_ALA-A1000_SW4-7_DEL_SVC-USERC_ALA-A1000_SW4-7_DEL_TRAFFDESC-PROFILEC_ALA-A1000_SW4-7_DEL_XDSL-PORTC_ALA-A1000_SW4-7_MOD_SHDSL-PARAMETERS
C_ALA-A1000_SW4-7_ACT_ADSL-PROFILEActivates an Asymmetric Digital Subscriber Line (ADSL) profile.
Table 52: C_ALA-A1000_SW4-7_ACT_ADSL-PROFILE
Parameter Name Description RangeDefault Value
Type Class
ADSLACT_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
ADSLACT_PROFILE_ID
The ADSL profile index.
1 to 40 S R
ADSLACT_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NE_ID_ALA_DSLAM Host NE identifier. S R
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 113
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
C_ALA-A1000_SW4-7_ACT_CRS-VCActivates a virtual circuit cross connect.
Table 53: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ACT_ADSL-PROFILE A_ALA-A1000_SW4-7_ACT_ADSL-PROFILE
Table 54: C_ALA-A1000_SW4-7_ACT_CRS-VC
Parameter Name Description RangeDefault Value
Type Class
LT_VCL Access identifier for the ATM virtual channel link in the LT/Server.
C R
NE_ID_ALA_DSLAM Host NE identifier. S R
NT_VCL Access identifier for the ATM virtual channel link in the NT/Server.
C R
VCCC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.Default value: 0
S O
VCCC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
Chapter 4: Service Definition
114 Oracle Corporation
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
C_ALA-A1000_SW4-7_ACT_CRS-VPActivates a virtual path cross connect.
Table 55: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ACT_CRS-VC A_ALA-A1000_SW4-7_ACT_CRS-VC
Table 56: C_ALA-A1000_SW4-7_ACT_CRS-VP
Parameter Name Description RangeDefault Value
Type Class
LT_VPL Access identifier for the ATM virtual path link in the LT/Server.
C R
NE_ID_ALA_DSLAM Host NE identifier. S R
NT_VPL Access identifier for the ATM virtual path link in the NT.
c R
VPCC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
VPCC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 115
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
C_ALA-A1000_SW4-7_ADD_ADSL-COMMON-PROFILEAdds an Asymmetric Digital Subscriber Line (ADSL) common profile.
Table 57: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ACT_CRS-VP A_ALA-A1000_SW4-7_ACT_CRS-VP
Table 58: C_ALA-A1000_SW4-7_ADD_ADSL-COMMON-PROFILE
Parameter Name Description RangeDefault Value
Type Class
ADSLCOM_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
ADSLCOM_NBLK The ADSL line parameter block containing one or more of the following named parameters with their values separated by commas:
ALWPROPGLITEALWPROPGDMTALWPWRCTL
C O
ADSLCOM_PROFILE_ID
The ADSL profile index.
1 to 40 S R
Chapter 4: Service Definition
116 Oracle Corporation
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
C_ALA-A1000_SW4-7_ADD_ADSL-DMT-PROFILEAdds an Asymmetric Digital Subscriber Line (ADSL) discrete multi-tone profile.
ADSLCOM_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NE_ID_ALA-DSLAM Host NE identifier. S R
Table 59: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_ADSL-COMMON-PROFILE
A_ALA-A1000_SW4-7_ADD_ADSL-COMMON-PROFILE
Table 60: C_ALA-A1000_SW4-7_ADD_ADSL-DMT-PROFILE
Parameter Name Description RangeDefault Value
Type Class
ADSLMSK_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
Table 58: C_ALA-A1000_SW4-7_ADD_ADSL-COMMON-PROFILE
Parameter Name Description RangeDefault Value
Type Class
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 117
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
ADSLMSK_NBLK The parameter block containing one or more of the following named parameters separated with their values by commas for provisioning the ADSL DMT carrier mask:
CMASK0CMASK1CMASK2CMASK3CMASK4CMASK5CMASK6CMASK7
C O
ADSLMSK_PROFILE_ID
The ADSL profile index.
1 to 40 S R
ADSLMSK_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NE_ID_ALA_DSLAM Host NE identifier. S R
Table 61: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_ADSL-DMT-PROFILE
A_ALA-A1000_SW4-7_ADD_ADSL-DMT-PROFILE
Table 60: C_ALA-A1000_SW4-7_ADD_ADSL-DMT-PROFILE
Parameter Name Description RangeDefault Value
Type Class
Chapter 4: Service Definition
118 Oracle Corporation
C_ALA-A1000_SW4-7_ADD_ADSL-DOWNSTREAM-PROFILEAdds an Asymmetric Digital Subscriber Line (ADSL) downstream profile.
Table 62: C_ALA-A1000_SW4-7_ADD_ADSL-DOWNSTREAM-PROFILE
Parameter Name Description RangeDefault Value
Type Class
ADSLDN_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
ADSLDN_PROFILE_ID
The ADSL profile index.
1 to 40 S R
ADSLDN_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 119
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
ADSLPROF_NBLK The ADSL line parameter block containing one or more of the following named parameters with their values separated by commas:
MINNMRMAXNMRTNMRMAXPSDMAXAPLVLRAMODEPIBRMAXIBRMINIBRMAXIDELPFBRMAXFBRMINFBR
C O
NE_ID_ALA-DSLAM Host NE identifier. S R
Table 63: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_ADSL-DOWNSTREAM-PROFILE
A_ALA-A1000_SW4-7_ADD_ADSL-DOWNSTREAM-PROFILE
Table 62: C_ALA-A1000_SW4-7_ADD_ADSL-DOWNSTREAM-PROFILE
Parameter Name Description RangeDefault Value
Type Class
Chapter 4: Service Definition
120 Oracle Corporation
C_ALA-A1000_SW4-7_ADD_ADSL-LINE-PROFILEAdds an Asymmetric Digital Subscriber Line (ADSL) line profile.
Table 64: C_ALA-A1000_SW4-7_ADD_ADSL-LINE-PROFILE
Parameter Name Description RangeDefault Value
Type Class
ADSLDN_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
ADSLDN_PROFILE_ID
The ADSL profile index.
1 to 40 S R
ADSLDN_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 121
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
ADSLPROF_NBLK The ADSL line parameter block containing one or more of the following named parameters with their values separated by commas:
MINNMRMAXNMRTNMRMAXPSDMAXAPLVLRAMODEPIBRMAXIBRMINIBRMAXIDELPFBRMAXFBRMINFBR
C O
NE_ID_ALA-DSLAM Host NE identifier. S R
Table 65: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_ADSL-LINE-PROFILE
A_ALA-A1000_SW4-7_ADD_ADSL-LINE-PROFILE
Table 64: C_ALA-A1000_SW4-7_ADD_ADSL-LINE-PROFILE
Parameter Name Description RangeDefault Value
Type Class
Chapter 4: Service Definition
122 Oracle Corporation
C_ALA-A1000_SW4-7_ADD_ADSL-PORTAdds an Asymmetric Digital Subscriber Line (ADSL) port.
Table 66: C_ALA-A1000_SW4-7_ADD_ADSL-PORT
Parameter Name Description RangeDefault Value
Type Class
ADSLP_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
ADSLP_PST The desired primary state to be set.
IN (In-Service)OOS (Out-Of-Service)
S O
ADSLP_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
ADSL_NBLK The ADSL line parameter block containing one or more of the following named parameters with their values separated by commas:
PORTIDADSLPROFADSLPROFNM
C O
AID_ADSL Access identifier for the ADSL line.
C R
NE_ID_ALA_DSLAM Host NE identifier. S R
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 123
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
C_ALA-A1000_SW4-7_ADD_ADSL-PROFILEAdds an Asymmetric Digital Subscriber Line (ADSL) profile.
Table 67: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_ADSL-PORT A_ALA-A1000_SW4-7_ADD_ADSL-PORT
Table 68: C_ALA-A1000_SW4-7_ADD_ADSL-PROFILE
Parameter Name Description RangeDefault Value
Type Class
ADSLACT_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
ADSLACT_PROFILE_ID
The ADSL profile index.
1 to 40 s R
ADSLACT_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
s O
ADSLCOM_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
s O
Chapter 4: Service Definition
124 Oracle Corporation
ADSLCOM_NBLK The ADSL line parameter block containing one or more of the following named parameters with their values separated by commas:
ALWPROPGLITEALWPROPGDMTALWPWRCTL
C O
ADSLCOM_PROFILE_ID
The ADSL profile index.
1 to 40 S R
ADSLCOM_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
ADSLDN_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
ADSLDN_PROFILE_ID
The ADSL profile index.
1 to 40 S R
ADSLDN_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
Table 68: C_ALA-A1000_SW4-7_ADD_ADSL-PROFILE
Parameter Name Description RangeDefault Value
Type Class
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 125
ADSLLP_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
ADSLLP_PROFILE_ID
The ADSL profile index.
1 to 40 S R
ADSLLP_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
ADSLMSK_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
Table 68: C_ALA-A1000_SW4-7_ADD_ADSL-PROFILE
Parameter Name Description RangeDefault Value
Type Class
Chapter 4: Service Definition
126 Oracle Corporation
ADSLMSK_NBLK The parameter block containing one or more of the following named parameters separated with their values seperated by commas for provisioning the ADSL DMT carrier mask:
CMASK0CMASK1CMASK2CMASK3CMASK4CMASK5CMASK6CMASK7
C O
ADSLMSK_PROFILE_ID
The ADSL profile index.
1 to 40 S R
ADSLMSK_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
ADSLPROF_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
ADSLPROF_LATENCY
The latency of the ADSL line.
FASTINTERLEAVED
S O
Table 68: C_ALA-A1000_SW4-7_ADD_ADSL-PROFILE
Parameter Name Description RangeDefault Value
Type Class
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 127
ADSLPROF_NBLK The ADSL line parameter block containing one or more of the following named parameters with their values separated by commas:MINNMRMAXNMRTNMRMAXPSDMAXAPLVLRAMODEPIBRMAXIBRMINIBRMAXIDELPFBRMAXFBRMINFBR
C O
ADSLPROF_PROFILE_ID
The ADSL profile index.
1 to 40 S R
ADSLPROF_ PROFILE_NAME
Uniquely identifies this profile within its scope.
A string, 1 to 32 characters long.
S R
ADSLPROF_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NE_ID_ALA-DSLAM Host NE identifier. S R
Table 68: C_ALA-A1000_SW4-7_ADD_ADSL-PROFILE
Parameter Name Description RangeDefault Value
Type Class
Chapter 4: Service Definition
128 Oracle Corporation
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
Table 69: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_ADSL-PROFILE A_ALA-A1000_SW4-7_ADD_ADSL-PROFILE
A_ALA-A1000_SW4-7_ADD_ADSL-LINEPROFILE
A_ALA-A1000_SW4-7_ADD_ADSL-COMMONPROFILE
A_ALA-A1000_SW4-7_ADD_ADSLDOWNSTREAM-PROFILE
A_ALA-A1000_SW4-7_ADD_ADSL-DMTPROFILE
A_ALA-A1000_SW4-7_ACT_ADSL-PROFILE
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 129
C_ALA-A1000_SW4-7_ADD_ADSL-UPSTREAM-PROFILEAdds an Asymmetric Digital Subscriber Line (ADSL) upstream profile.
Table 70: C_ALA-A1000_SW4-7_ADD_ADSL-UPSTREAM-PROFILE
Parameter Name Description RangeDefault Value
Type Class
ADSLPROF_NBLK The ADSL line parameter block containing one or more of the following named parameters with their values separated by commas:
MINNMRMAXNMRTNMRMAXAPLVLRAMODEPIBRMAXIBRMINIBRMAXIDELPFBRMAXFBRMINFBR
C O
ADSLUP_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
ADSLUP_PROFILE_ID
The ADSL profile index.
1 to 40 S R
Chapter 4: Service Definition
130 Oracle Corporation
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
C_ALA-A1000_SW4-7_ADD_ATM-PORTAdds an ATM port.
ADSLUP_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NE_ID_ALA-DSLAM Host NE identifier. S R
Table 71: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_ADSL-UPSTREAM-PROFILE
A_ALA-A1000_SW4-7_ADD_ADSL-UPSTREAM-PROFILE
Table 72: C_ALA-A1000_SW4-7_ADD_ATM-PORT
Parameter Name Description RangeDefault Value
Type Class
AID_ATMPORT Access identifier for the ATM port.
C R
Table 70: C_ALA-A1000_SW4-7_ADD_ADSL-UPSTREAM-PROFILE
Parameter Name Description RangeDefault Value
Type Class
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 131
ATMPORT_NBLK The ATM port parameter block containing one or more of the following named parameters with their values separated by commas:
IFTYPECACPROFDNCACPROFDNNMACPROFUPCACPROFUPNMATMACCPROFATMACCPROFNMCDVTPROFCDVTPROFNMNGCRWEIGHT
C O
ATMP_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
ATMP_PST The desired primary state to be set.
IS (In-Service)OOS (Out-Of-Service)
S O
ATMP_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NE_ID_ALA-DSLAM Host NE identifier. S R
Table 72: C_ALA-A1000_SW4-7_ADD_ATM-PORT
Parameter Name Description RangeDefault Value
Type Class
Chapter 4: Service Definition
132 Oracle Corporation
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
C_ALA-A1000_SW4-7_ADD_ATM-PVCL-LTAdds an ATM Permanent Virtual Circuit (PVC) link on the line side.
Table 73: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_ATM-PORT A_ALA-A1000_SW4-7_ADD_ATM-PORT
Table 74: C_ALA-A1000_SW4-7_ADD_ATM-PVCL-LT
Parameter Name Description RangeDefault Value
Type Class
AID_VCL Access identifier for the ATM virtual channel link.
C R
NE_ID_ALA-DSLAM Host NE identifier. S R
VCL_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
VCL_NBLK The ATM VCL parameter block containing one or more of the following named parameters with their values separated by commas:
LINKTYPESEGENDPT
C O
VCL_RCV_TRAFD SC
The traffic descriptor profile index for the receive direction.
1 to 310 S O
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 133
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
VCL_RCV_TRAFDSCNM
The traffic descriptor profile name for the receive direction.
S O
VCL_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
VCL_XMT_ TRAFDSC
The transmit traffic descriptor profile index for the transmit direction.
1 to 310 S O
VCL_XMT_ TRAFDSCNM
The traffic descriptor profile name for the transmit direction.
S O
Table 75: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_ATM-PVCL-LT A_ALA-A1000_SW4-7_ADD_ATM-PVCL-LT
Table 74: C_ALA-A1000_SW4-7_ADD_ATM-PVCL-LT
Parameter Name Description RangeDefault Value
Type Class
Chapter 4: Service Definition
134 Oracle Corporation
C_ALA-A1000_SW4-7_ADD_ATM-PVCL-NTAdds an ATM Permanent Virtual Circuit (PVC) link on network side.
Table 76: C_ALA-A1000_SW4-7_ADD_ATM-PVCL-NT
Parameter Name Description RangeDefault Value
Type Class
AID_VCL Access identifier for the ATM virtual channel link.
C R
NE_ID_ALA-DSLAM Host NE identifier. S R
VCL_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
VCL_NBLK The ATM VCL parameter block containing one or more of the following named parameters with their values separated by commas:
LINKTYPESEGENDPT
C O
VCL_RCV_TRAFDSC The traffic descriptor profile index for the receive direction.
1 to 310 S O
VCL_RCV_TRAFD SCNM
The traffic descriptor profile name for the receive direction.
S O
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 135
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
C_ALA-A1000_SW4-7_ADD_ATM-PVPLAdds an ATM Private Virtual Path (PVP) link.
VCL_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
VCL_XMT_ TRAFDSC
The transmit traffic descriptor profile index for the transmit direction.
1 to 310 S O
VCL_XMT_ TRAFDSCNM
The traffic descriptor profile name for the transmit direction.
S O
Table 77: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_ATM-PVCL-NT A_ALA-A1000_SW4-7_ADD_ATM-PVCL-NT
Table 78: C_ALA-A1000_SW4-7_ADD_ATM-PVPL
Parameter Name Description RangeDefault Value
Type Class
AID_VPL Access identifier for the ATM virtual path link.
C R
NE_ID_ALA-DSLAM Host NE identifier. S R
Table 76: C_ALA-A1000_SW4-7_ADD_ATM-PVCL-NT
Parameter Name Description RangeDefault Value
Type Class
Chapter 4: Service Definition
136 Oracle Corporation
VPL_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.Default value: 0
S O
VPL_NBLK The ATM VPL parameter block containing one or more of the following named parameters with their values separated by commas:
LINKTYPESEGENDPT
C O
VPL_RCV_TRAFDSC The traffic descriptor profile index for the receive direction.
1 to 310 S O
VPL_RCV_TRAFDSCNM
The traffic descriptor profile name for the receive direction.
S O
VPL_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
VPL_XMT_ TRAFDS C
The transmit traffic descriptor profile index for the transmit direction.
1 to 310 S O
VPL_XMT_ TRAFDSCNM
The traffic descriptor profile name for the transmit direction.
S O
Table 78: C_ALA-A1000_SW4-7_ADD_ATM-PVPL
Parameter Name Description RangeDefault Value
Type Class
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 137
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
C_ALA-A1000_SW4-7_ADD_ATMACC-PROFILEAdds an ATM access profile.
Table 79: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_ATM-PVPL A_ALA-A1000_SW4-7_ADD_ATM-PVPL
Table 80: C_ALA-A1000_SW4-7_ADD_ATMACC-PROFILE
Parameter Name Description RangeDefault Value
Type Class
ATMACC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
ATMACC_NBLK The ATM access profile parameter block containing one or more of the following named parameters with their values separated by commas:
GFCMODEMAXVPCSMAXVCCSVPIBITSVCIBITSPOLICINGSVCMAXVPISVCMINVCI
C O
ATMACC_PROFILE_ID
The ATM access profile index.
1 to 50 S R
Chapter 4: Service Definition
138 Oracle Corporation
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
ATMACC_PROFILE_ NAME
Uniquely identifies this profile within its scope.
A string, 1 to 32 characters long.
S R
ATMACC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NE_ID_ALA-DSLAM Host NE identifier. S R
Table 81: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_ATMACC-PROFILE A_ALA-A1000_SW4-7_ADD_ATMACC-PROFILE
Table 80: C_ALA-A1000_SW4-7_ADD_ATMACC-PROFILE
Parameter Name Description RangeDefault Value
Type Class
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 139
C_ALA-A1000_SW4-7_ADD_CAC-PROFILEAdds a Connection Admission Control (CAC) profile.
Table 82: C_ALA-A1000_SW4-7_ADD_CAC-PROFILE
Parameter Name Description RangeDefault Value
Type Class
CACPROF_NBLK The ATM CAC profile parameter block containing one or more of the following named parameters with their values separated by commas:
CBRMAXCONCBRBWSECFACCBRBUFSECFACUBRMAXCONUBRMCRSECFACRTVBRMAXCONRTVBRBWSECFACRTVBRBUFSECFACRTVBRNGCRSECFACRTVBROVRBKFACNRTVBRMAXCONNRTVBRBWSECFACNRTVBRBUFSECFACNRTVBRNGCRSECFACNRTVBRNGCRSECFACGFRMAXCONGFRBWSECFACGFRBUFSECFACFROVRBKFACAGRBWSECFACAGRGCRSECFAC
C O
Chapter 4: Service Definition
140 Oracle Corporation
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
CAC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
CAC_PROFILE_ID The numeric identifier of the profile.
1 to 50 S R
CAC_PROFILE_NAME
Uniquely identifies this profile within its scope.
A string, 1 to 32 characters long.
S R
CAC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NE_ID_ALA-DSLAM Host NE identifier. S R
Table 83: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_CAC-PROFILE A_ALA-A1000_SW4-7_ADD_CAC-PROFILE
Table 82: C_ALA-A1000_SW4-7_ADD_CAC-PROFILE
Parameter Name Description RangeDefault Value
Type Class
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 141
C_ALA-A1000_SW4-7_ADD_CDVT-PROFILEAdds a Cell Delay Variance Tollerance (CDVT) profile.
Table 84: C_ALA-A1000_SW4-7_ADD_CDVT-PROFILE
Parameter Name Description RangeDefault Value
Type Class
CDVTPROF_NBLK The ATM CDVT Profile parameter block containing one or more of the following named parameters with their values separated by commas:
CDVTCBRCDVTUBRCDVTRTVBRCDVTNRTVBRCDVTGFR
C O
CDVT_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
CDVTP_ROFILE_ID The AT M cell delay variation tolerance profile index.
1 to 20 S R
CDVT_PROFILE_NAME
Uniquely identifies this profile within its scope.
A string, 1 to 32 characters long.
S R
CDVT_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NE_ID_ALA-DSLAM Host NE identifier. S R
Chapter 4: Service Definition
142 Oracle Corporation
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
C_ALA-A1000_SW4-7_ADD_CRS-VCAdds a virtual circuit cross connect.
Table 85: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_CDVT-PROFILE A_ALA-A1000_SW4-7_ADD_CDVT-PROFILE
Table 86: C_ALA-A1000_SW4-7_ADD_CRS-VC
Parameter Name Description RangeDefault Value
Type Class
LT_VCL Access identifier for the ATM virtual channel link in the LT/Server.
C R
NE_ID_ALA-DSLAM Host NE identifier. S R
NT_VCL Access identifier for the ATM virtual channel link in the NT/Server.
C R
VCCC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
VCCC_PST The desired primary state to be set.
IS (In-Service)OOS (Out-Of-Service)
S O
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 143
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
C_ALA-A1000_SW4-7_ADD_CRS-VPAdds a virtual path cross connect.
VCCC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
Table 87: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_CRS-VC A_ALA-A1000_SW4-7_ADD_CRS-VC
Table 88: C_ALA-A1000_SW4-7_ADD_CRS-VP
Parameter Name Description RangeDefault Value
Type Class
LT_VPL Access identifier for the ATM virtual path link in the LT/Server.
C R
NE_ID_ALA-DSLAM Host NE identifier. S R
NT_VPL Access identifier for the ATM virtual path link in the NT.
C R
Table 86: C_ALA-A1000_SW4-7_ADD_CRS-VC
Parameter Name Description RangeDefault Value
Type Class
Chapter 4: Service Definition
144 Oracle Corporation
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
C_ALA-A1000_SW4-7_ADD_OC3-INTERFACEAdds an OC3 interface.
VPCC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.Default value: 0
S O
VPCC_PST The desired primary state to be set.
IS (In-Service)OOS (Out-Of-Service)
S O
VPCC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
Table 89: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_CRS-VP A_ALA-A1000_SW4-7_ADD_CRS-VP
Table 90: C_ALA-A1000_SW4-7_ADD_OC3-INTERFACE
Parameter Name Description RangeDefault Value
Type Class
AID_OC3 Access identifier for the OC3 facility.
C R
Table 88: C_ALA-A1000_SW4-7_ADD_CRS-VP
Parameter Name Description RangeDefault Value
Type Class
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 145
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
NE_ID_ALA-DSLAM Host NE identifier. S R
OC3_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
OC3_NBLK OC3 facility parameter block containing the following named parameters with their values: OPMODE.
C O
OC3_PST The desired primary state to be set.
IN (In-Service)OOS (Out-Of-Service)
S O
OC3_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
Table 91: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_OC3-INTERFACE A_ALA-A1000_SW4-7_ADD_OC3-INTERFACE
Table 90: C_ALA-A1000_SW4-7_ADD_OC3-INTERFACE
Parameter Name Description RangeDefault Value
Type Class
Chapter 4: Service Definition
146 Oracle Corporation
C_ALA-A1000_SW4-7_ADD_SHDSL-PARAMETERSAdds SHDSL parameters.
Table 92: C_ALA-A1000_SW4-7_ADD_SHDSL-PARAMETERS
Parameter Name Description RangeDefault Value
Type Class
AID_SHDSL The access identifier for the SHDSL circuit.
C R
NE_ID_ALA-DSLAM Host NE identifier. S R
SHDSLCTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
SHDSL_NBLK The SHDSL circuit parameter block containing one or more of the following named parameters with their values separated by commas:
PORTIDPSDTYPEWIREMODEMINLINERATEMAXLINERATETARRMDNWCTARRMDNCCTARRMUPWCTARRMUPCCREMOTEMGTREGIONCONFIMAGRP
C R
SHDSL_NUM_REPEATERS
Number of repeaters provisioned for this SHDSL span.
S O
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 147
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
C_ALA-A1000_SW4-7_ADD_SIG-CHANNELAdds a signalling channel.
SHDSLPST The desired primary state to be set.
IS (In-Service)OOS (Out-Of-Service)
S O
SHDSLTID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
Table 93: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_SHDSL-PARAMETERS
A_ALA-A1000_SW4-7_ADD_SHDSL-PARAMETERS
Table 94: C_ALA-A1000_SW4-7_ADD_SIG-CHANNEL
Parameter Name Description RangeDefault Value
Type Class
AID_SIGCHN Access identifier for the ATM signaling channel.
C R
NE_ID_ALA-DSLAM Host NE identifier. S R
Table 92: C_ALA-A1000_SW4-7_ADD_SHDSL-PARAMETERS
Parameter Name Description RangeDefault Value
Type Class
Chapter 4: Service Definition
148 Oracle Corporation
SIGCHN_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
SIGCHN_NBLK The signaling channel parameter block containing one or more of the following named parameters with their values separated by commas
:XMITTRAFDSCRXMITTRAFDSCRNMRECVTRAFDSCRRECVTRAFDSCRNMMAXACTCALLSSAALPROFSAALPROFNMSAALMODEDSS2PROFDSS2PROFNMSIGPERFPROFSIGPERFPROFNMMULTIPOINTSEGENDPT
C R
SIGCHN_STATE The desired state to be set.
S O
Table 94: C_ALA-A1000_SW4-7_ADD_SIG-CHANNEL
Parameter Name Description RangeDefault Value
Type Class
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 149
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
C_ALA-A1000_SW4-7_ADD_SIG-CHANNEL-PARAMSAdds signalling channel parameters.
SIGCHN_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.Default value: NULL
S O
SIGCHN_VCI The VCI value associated with the signaling channel.
S O
SIGCHN_VPI The VPI value associated with the signaling channel.
S O
Table 95: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_SIG-CHANNEL A_ALA-A1000_SW4-7_ADD_SIG-CHANNEL
Table 96: C_ALA-A1000_SW4-7_ADD_SIG-CHANNEL-PARAMS
Parameter Name Description RangeDefault Value
Type Class
AID_SIGCHN Access identifier for the ATM signaling channel.
C R
NE_ID_ALA-DSLAM Host NE identifier. S R
Table 94: C_ALA-A1000_SW4-7_ADD_SIG-CHANNEL
Parameter Name Description RangeDefault Value
Type Class
Chapter 4: Service Definition
150 Oracle Corporation
SIGCHNP_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
SIGCHNP_STATE The desired state to be set.
S O
SIGCHNP_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
SIGCHN_NBLK The signaling channel parameter block containing one or more of the following named parameters with their values separated by commas:
MAXACTCALLSSAALPROFSAALPROFNMSAALMODEDSS2PROFDSS2PROFNMSIGPERFPROFSIGPERFPROFNMMULTIPOINTSEGENDPT
C O
Table 96: C_ALA-A1000_SW4-7_ADD_SIG-CHANNEL-PARAMS
Parameter Name Description RangeDefault Value
Type Class
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 151
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
C_ALA-A1000_SW4-7_ADD_SVC-USERAdds a Switched Virtual Circuit (SVC) user.
Table 97: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_SIG-CHANNEL-PARAMS
A_ALA-A1000_SW4-7_ADD_SIG-CHANNEL-PARAMS
Table 98: C_ALA-A1000_SW4-7_ADD_SVC-USER
Parameter Name Description RangeDefault Value
Type Class
ATM_ADDRESS Access identifier for the SVC user.
S R
ATM_PORT ATM port associated with the SVC user.
C R
NE_ID_ALA-DSLAM Host NE identifier. S R
SVCUSER_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
Chapter 4: Service Definition
152 Oracle Corporation
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
SVCUSER_NBLK The SVC user parameter block containing one or more of the following named parameters with their values separated by commas:
CICALLOWCALLINALLOWCALLOUTIDENTPROFIDENTPROFNM
C R
SVCUSER_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
Table 99: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_SVC-USER A_ALA-A1000_SW4-7_ADD_SVC-USER
Table 98: C_ALA-A1000_SW4-7_ADD_SVC-USER
Parameter Name Description RangeDefault Value
Type Class
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 153
C_ALA-A1000_SW4-7_ADD_T1DS1-INTERFACEAdds T1/DS1 interface.
Table 100: C_ALA-A1000_SW4-7_ADD_T1DS1-INTERFACE
Parameter Name Description RangeDefault Value
Type Class
AID_DS1 Access identifier for the T1 (DS1) facility.
C R
DS1_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
DS1_NBLK The DS1 facility parameter block containing one or more of the following named parameters with their values separated by commas:
PORTIDLINETYPELBOEQLZ
C R
DS1_PST The desired primary state to be set.
IN (In-Service)OOS (Out-Of-Service)
S O
DS1_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NE_ID_ALA-DSLAM Host NE identifier. S R
Chapter 4: Service Definition
154 Oracle Corporation
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
C_ALA-A1000_SW4-7_ADD_T3DS3-INTERFACEAdds T3/DS3 interface.
Table 101: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_T1DS1-INTERFACE A_ALA-A1000_SW4-7_ADD_T1DS1-INTERFACE
Table 102: C_ALA-A1000_SW4-7_ADD_T3DS3-INTERFACE
Parameter Name Description RangeDefault Value
Type Class
AID_DS3 Access identifier for the T3 (DS3) facility.
C R
DS3_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
DS3_NBLK The DS3 facility parameter block containing one or more of the following named parameters with their values separated by commas:
CELLMAPNGCRDECPLNGOOFDETECTLINEBLDOUT
C O
DS3_PST The desired primary state to be set.
IN (In-Service)OOS (Out-Of-Service)
S O
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 155
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
C_ALA-A1000_SW4-7_ADD_TRAFFDESC-PROFILEAdds traffic descriptor profile.
DS3_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NE_ID_ALA-DSLAM Host NE identifier. S R
Table 103: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_T3DS3-INTERFACE A_ALA-A1000_SW4-7_ADD_T3DS3-INTERFACE
Table 104: C_ALA-A1000_SW4-7_ADD_TRAFFDESC-PROFILE
Parameter Name Description RangeDefault Value
Type Class
NE_ID_ALA-DSLAM Host NE identifier. S R
TRAFDSC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
Table 102: C_ALA-A1000_SW4-7_ADD_T3DS3-INTERFACE
Parameter Name Description RangeDefault Value
Type Class
Chapter 4: Service Definition
156 Oracle Corporation
TRAFDSC_NBLK The ATM Traffic Descriptor profile parameter block containing one or more of the following named parameters with their values separated by commas:
FRAMEDSCCLP1PCRCDVTCLP1MCRCLP1SCRMBSCLP0SCRMFS
These values are added to MML based on parameter TRAFDSC TYPE value.
C R
TRAFDSC_PROFILE_ ID
The numeric identifier of the profile.
1 to 310 S R
TRAFDSC_PROFILE_ NAME
Uniquely identifies this profile within its scope.
A string, 1 to 32 characters long.
S R
TRAFDSC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
TRAFDSC_TYPE Traffic descriptor service category type.
S O
Table 104: C_ALA-A1000_SW4-7_ADD_TRAFFDESC-PROFILE
Parameter Name Description RangeDefault Value
Type Class
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 157
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
C_ALA-A1000_SW4-7_ADD_XDSL-PORTAdds an XDSL port.
Table 105: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_TRAFFDESC-PROFILE
A_ALA-A1000_SW4-7_ADD_TRAFFDESC-PROFILE
Table 106: C_ALA-A1000_SW4-7_ADD_XDSL-PORT
Parameter Name Description RangeDefault Value
Type Class
AID_XDSL Access identifier for the ADSL line.
C R
NE_ID_ALA-DSLAM Host NE identifier. S R
XDSL_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
Chapter 4: Service Definition
158 Oracle Corporation
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
XDSL_NBLK The ADSL line parameter block containing one or more of the following named parameters with their values separated by commas:
PORTIDXSRVCROFNMXSRVCPROFIDXLNEROFNMXLNEPROFIDOPMASKAOPMASKA2OPMASKVOPMASKA2MBONDMODTYPE
C O
XDSL_PST The desired primary state to be set.
IN (In-Service)OOS (Out-Of-Service)
S O
XDSL_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
Table 107: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_ADD_XDSL-PORT A_ALA-A1000_SW4-7_ADD_XDSL-PORT
Table 106: C_ALA-A1000_SW4-7_ADD_XDSL-PORT
Parameter Name Description RangeDefault Value
Type Class
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 159
C_ALA-A1000_SW4-7_DEACT_CRS-VCDeactivates a virtual circuit cross connect.
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
Table 108: C_ALA-A1000_SW4-7_DEACT_CRS-VC
Parameter Name Description RangeDefault Value
Type Class
LT_VCL Access identifier for the ATM virtual channel link in the LT/Server.
C R
NE_ID_ALA-DSLAM Host NE identifier. S R
NT_VCL Access identifier for the ATM virtual channel link in the NT/Server.
C R
VCCC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
VCCC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
Table 109: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_DEACT_CRS-VC A_ALA-A1000_SW4-7_DEACT_CRS-VC
Chapter 4: Service Definition
160 Oracle Corporation
C_ALA-A1000_SW4-7_DEACT_CRS-VPDeactives a virtual path cross connect.
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
Table 110: C_ALA-A1000_SW4-7_DEACT_CRS-VP
Parameter Name Description RangeDefault Value
Type Class
LT_VPL Access identifier for the ATM virtual path link in the LT/Server.
C R
NE_ID_ALA-DSLAM Host NE identifier. S R
NT_VPL Access identifier for the ATM virtual path link in the NT.
C R
VPCC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
VPCC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
Table 111: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_DEACT_CRS-VP A_ALA-A1000_SW4-7_DEACT_CRS-VP
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 161
C_ALA-A1000_SW4-7_DEL_ADSL-PORTDeletes an Asymmetric Digital Subscriber Line (ADSL) port.
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
Table 112: C_ALA-A1000_SW4-7_DEL_ADSL-PORT
Parameter Name Description RangeDefault Value
Type Class
ADSLP_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
ADSLP_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NE_ID_ALA-DSLAM Host NE identifier. S R
PORT_AID The AID for the user port.
C R
Table 113: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_DEL_ADSL-PORT A_ALA-A1000_SW4-7_DEL_ADSL-PORT
Chapter 4: Service Definition
162 Oracle Corporation
C_ALA-A1000_SW4-7_DEL_ATM-PVCL-LTDeletes an ATM Permanent Virtual Circuit (PVC) link from the line side.
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
Table 114: C_ALA-A1000_SW4-7_DEL_ATM-PVCL-LT
Parameter Name Description RangeDefault Value
Type Class
AID_VCL Access identifier for the ATM virtual channel link.
C R
NE_ID_ALA-DSLAM Host NE identifier. S R
VCL_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
VCL_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
Table 115: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_DEL_ATM-PVCL-LT A_ALA-A1000_SW4-7_DEL_ATM-PVCL-LT
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 163
C_ALA-A1000_SW4-7_DEL_ATM-PVCL-NTDeletes an ATM Permanent Virtual Circuit (PVC) link from the network side.
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
Table 116: C_ALA-A1000_SW4-7_DEL_ATM-PVCL-NT
Parameter Name Description RangeDefault Value
Type Class
AID_VCL Access identifier for the ATM virtual channel link.
C R
NE_ID_ALA-DSLAM Host NE identifier. S R
VCL_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
VCL_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
Table 117: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_DEL_ATM-PVCL-NT A_ALA-A1000_SW4-7_DEL_ATM-PVCL-NT
Chapter 4: Service Definition
164 Oracle Corporation
C_ALA-A1000_SW4-7_DEL_ATM-PVPLDeletes an ATM Private Virtual Path (PVP) link.
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
Table 118: C_ALA-A1000_SW4-7_DEL_ATM-PVPL
Parameter Name Description RangeDefault Value
Type Class
AID_VPL Access identifier for the ATM virtual path link.
C R
NE_ID_ALA-DSLAM Host NE identifier. S R
VPL_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
VPL_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
Table 119: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_DEL_ATM-PVPL A_ALA-A1000_SW4-7_DEL_ATM-PVPL
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 165
C_ALA-A1000_SW4-7_DEL_ATMACC-PROFILEDeletes an ATM access profile.
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
Table 120: C_ALA-A1000_SW4-7_DEL_ATMACC-PROFILE
Parameter Name Description RangeDefault Value
Type Class
ATMACC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
ATMACC_PROFILE_ID
The ATM access profile index.
1 to 50 S R
ATMACC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NE_ID_ALA-DSLAM Host NE identifier. S R
Table 121: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_DEL_ATMACC-PROFILE A_ALA-A1000_SW4-7_DEL_ATMACC-PROFILE
Chapter 4: Service Definition
166 Oracle Corporation
C_ALA-A1000_SW4-7_DEL_CAC-PROFILEDeletes a Connection Admission Control (CAC) profile.
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
Table 122: C_ALA-A1000_SW4-7_DEL_CAC-PROFILE
Parameter Name Description RangeDefault Value
Type Class
CAC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
CAC_PROFILE_ID The numeric identifier of the profile.
1 to 50 S R
CAC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NE_ID_ALA-DSLAM Host NE identifier. S R
Table 123: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_DEL_CAC-PROFILE A_ALA-A1000_SW4-7_DEL_CAC-PROFILE
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 167
C_ALA-A1000_SW4-7_DEL_CDVT-PROFILEDeletes a Cell Delay Variance Tollerance (CDVT) profile.
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
Table 124:
Parameter Name Description RangeDefault Value
Type Class
CDVT_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
CDVT_PROFILE_ID The AT M cell delay variation tolerance profile index.
1 to 20 S R
CDVT_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NE_ID_ALA-DSLAM Host NE identifier. S R
Table 125: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_DEL_CDVT-PROFILE A_ALA-A1000_SW4-7_DEL_CDVT-PROFILE
Chapter 4: Service Definition
168 Oracle Corporation
C_ALA-A1000_SW4-7_DEL_CRS-VCDeletes a virtual circuit cross connect.
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
Table 126: C_ALA-A1000_SW4-7_DEL_CRS-VC
Parameter Name Description RangeDefault Value
Type Class
LT_VCL Access identifier for the ATM virtual channel link in the LT/Server.
C R
NE_ID_ALA-DSLAM Host NE identifier. S R
NT_VCL Access identifier for the ATM virtual channel link in the NT/Server.
C R
VCCC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
VCCC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
Table 127: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_DEL_CRS-VC A_ALA-A1000_SW4-7_DEL_CRS-VC
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 169
C_ALA-A1000_SW4-7_DEL_CRS-VPDeletes a virtual path cross connect.
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
Table 128: C_ALA-A1000_SW4-7_DEL_CRS-VP
Parameter Name Description RangeDefault Value
Type Class
LT_VPL Access identifier for the ATM virtual path link in the LT/Server.
C R
NE_ID_ALA-DSLAM Host NE identifier. S R
NT_VPL Access identifier for the ATM virtual path link in the NT.
C R
VPCC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
VPCC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
Table 129: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_DEL_CRS-VP A_ALA-A1000_SW4-7_DEL_CRS-VP
Chapter 4: Service Definition
170 Oracle Corporation
C_ALA-A1000_SW4-7_DEL_DSL-PROFILEDeletes an Asymmetric Digital Subscriber Line (ADSL) profile.
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
Table 130: C_ALA-A1000_SW4-7_DEL_DSL-PROFILE
Parameter Name Description RangeDefault Value
Type Class
ADSLDLT_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
ADSLDLT_PROFILE_ ID
The ADSL profile index.
1 to 40 S R
ADSLDLT_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
NE_ID_ALA-DSLAM Host NE identifier. S R
Table 131: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_DEL_DSL-PROFILE A_ALA-A1000_SW4-7_DEL_DSL-PROFILE
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 171
C_ALA-A1000_SW4-7_DEL_SIG-CHANNELDeletes signaling channel.
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
Table 132: C_ALA-A1000_SW4-7_DEL_SIG-CHANNEL
Parameter Name Description RangeDefault Value
Type Class
AID_SIGCHN Access identifier for the ATM signaling channel.
C R
NE_ID_ALA-DSLAM Host NE identifier. S R
SIGCHN_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
SIGCHN_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
Table 133: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_DEL_SIG-CHANNEL A_ALA-A1000_SW4-7_DEL_SIG-CHANNEL
Chapter 4: Service Definition
172 Oracle Corporation
C_ALA-A1000_SW4-7_DEL_SVC-USERDeletes a Switched Virtual Circuit (SVC) user.
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
Table 134: C_ALA-A1000_SW4-7_DEL_SVC-USER
Parameter Name Description RangeDefault Value
Type Class
ATM_ADDRESS Access identifier for the SVC user.
S R
NE_ID_ALA-DSLAM Host NE identifier. S R
SVCUSER_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
SVCUSER_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
Table 135: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_DEL_SVC-USER A_ALA-A1000_SW4-7_DEL_SVC-USER
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 173
C_ALA-A1000_SW4-7_DEL_TRAFFDESC-PROFILEDeletes traffic descriptor profile.
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
Table 136: C_ALA-A1000_SW4-7_DEL_TRAFFDESC-PROFILE
Parameter Name Description RangeDefault Value
Type Class
NE_ID_ALA-DSLAM Host NE identifier. S R
TRAFDSC_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long. It is optional to specify.
Default value: 0
S O
TRAFDSC_PROFILE_ID
The numeric identifier of the profile.
1 to 310 S R
TRAFDSC_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
Table 137: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_DEL_TRAFFDESC-PROFILE
A_ALA-A1000_SW4-7_DEL_TRAFFDESC-PROFILE
Chapter 4: Service Definition
174 Oracle Corporation
C_ALA-A1000_SW4-7_DEL_XDSL-PORTDeletes an XDSL port.
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
Table 138: C_ALA-A1000_SW4-7_DEL_XDSL-PORT
Parameter Name Description RangeDefault Value
Type Class
NE_ID_ALA-DSLAM Host NE identifier. S R
PORT_AID The AID for the user port.
C R
XDSL_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
XDSL_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
Table 139: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_DEL_XDSL-PORT A_ALA-A1000_SW4-7_DEL_XDSL-PORT
CSDL commands
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 175
C_ALA-A1000_SW4-7_MOD_SHDSL-PARAMETERSModifies SHDSL parameters.
Table 140: C_ALA-A1000_SW4-7_MOD_SHDSL-PARAMETERS
Parameter Name Description RangeDefault Value
Type Class
AID_SHDSL The access identifier for the SHDSL circuit.
C R
NE_ID_ALA-DSLAM Host NE identifier. S R
SHDSL_CTAG The command correlation tag is used to correlate the response of the command with the original command itself.
An identifier or a decimal number up to six characters long.
S O
SHDSL_NBLK The SHDSL circuit parameter block containing one or more of the following named parameters with their values separated by commas:
PORTIDPSDTYPEWIREMODEMINLINERATEMAXLINERATETARRMDNWCTARRMDNCCTARRMUPWCTARRMUPCCREMOTEMGTREGIONCONFIMAGRP
C O
SHDSL_NUM_REPEATERS
Number of repeaters provisioned for this SHDSL span.
S O
Chapter 4: Service Definition
176 Oracle Corporation
Mapping to ASDLs
The following table illustrates the CSDL to ASDL mapping for this service.
SHDSL_PST The desired primary state to be set.
IN (In-Service)OOS (Out-Of-Service)
S O
SHDSL_TID The target identifier (TID) for the NE.
It should match the SID assigned to the NE, or be NULL. A NULL value matches the NE processing this command.
Default value: NULL
S O
Table 141: CSDL to ASDL Mapping
CSDL ASDL
C_ALA-A1000_SW4-7_MOD_SHDSL-PARAMETERS
A_ALA-A1000_SW4-7_MOD_SHDSL-PARAMETERS
Table 140: C_ALA-A1000_SW4-7_MOD_SHDSL-PARAMETERS
Parameter Name Description RangeDefault Value
Type Class
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 177
5
Configuring ASAP to Support Additional NE Instances
You can configure ASAP to support the Alcatel A1000 DSLAM - NEP configuration using the Service Activation Configuration Tool (SACT). Refer to the ASAP Administration Guide for more information.
Below is an example of the Activation.Configuration.XML file for the Alcatel A1000 DSLAM cartridge.<?xml version="1.0" encoding="UTF-8"?>
<activationConfig xmlns="http://www.metasolv.com/ServiceActivation/
2003/ActivationConfig" xmlns:xsi="http://www.w3.org/2001/XMLSchemainstance"
xsi:schemaLocation="http://www.metasolv.com/ServiceActivation/
2003/ActivationConfig
C:\schema\ASAP5-0\ActivationConfig.xsd">
<connectionPool name="ALADSL1">
<device name="ala_dsl_dev1">
<environment>DEVELOPMENT</environment>
<lineType>TELNET_CONNECTION</lineType>
</device>
<device name="ala_dsl_dev2">
<environment>DEVELOPMENT</environment>
<lineType>TELNET_CONNECTION</lineType>
</device>
<device name="ala_dsl_dev3">
<environment>DEVELOPMENT</environment>
<lineType>TELNET_CONNECTION</lineType>
</device>
</connectionPool>
<element name="ALA_DSL_HOST">
<technology>ALA-DSLAM</technology>
<softwareLoad>4-7</softwareLoad>
Chapter 5: Configuring ASAP to Support Additional NE Instances
178 Oracle Corporation
<nepServerName>$NEP</nepServerName>
<primaryPool>ALADSL1</primaryPool>
<maximumConnections>1</maximumConnections>
<dropTimeout>5</dropTimeout>
<spawnThreshold>1</spawnThreshold>
<killThreshold>0</killThreshold>
<routingElement name="ALA_DSL_HOST">
<atomicService/>
</routingElement>
<communicationParameter>
<label>HOST_IPADDR</label>
<value>
<value>192.168.1.1</value>
</value>
<description>Remote Host IP Address</description>
<deviceName>COMMON_DEVICE_CFG</deviceName>
<lineType>TELNET_CONNECTION</lineType>
</communicationParameter>
<communicationParameter>
<label>HOST_NAME</label>
<value>
<value>192.168.1.1</value>
</value>
<description>JEDD Server Host</description>
<deviceName>COMMON_DEVICE_CFG</deviceName>
<lineType>TELNET_CONNECTION</lineType>
</communicationParameter>
<communicationParameter>
<label>PORT</label>
<value>
<value>14000</value>
</value>
<description>Remote Host Port</description>
<deviceName>COMMON_DEVICE_CFG</deviceName>
<lineType>TELNET_CONNECTION</lineType>
</communicationParameter>
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 179
<communicationParameter>
<label>AMS_PORT</label>
<value>
<value>14000</value>
</value>
<description>Remote Host Port</description>
<deviceName>COMMON_DEVICE_CFG</deviceName>
<lineType>TELNET_CONNECTION</lineType>
</communicationParameter>
<communicationParameter>
<label>LOGIN_TIMEOUT</label>
<value>
<value>20000</value>
</value>
<description>Connection timeout</description>
<deviceName>COMMON_DEVICE_CFG</deviceName>
<lineType>TELNET_CONNECTION</lineType>
</communicationParameter>
<communicationParameter>
<label>READ_TIMEOUT</label>
<value>
<value>20000</value>
</value>
<description>Read timeout</description>
<deviceName>COMMON_DEVICE_CFG</deviceName>
<lineType>TELNET_CONNECTION</lineType>
</communicationParameter>
<communicationParameter>
<label>AMS_USER</label>
<value>
<value>metasolv</value>
</value>
<description>AMS User Name</description>
<deviceName>COMMON_DEVICE_CFG</deviceName>
<lineType>TELNET_CONNECTION</lineType>
</communicationParameter>
Chapter 5: Configuring ASAP to Support Additional NE Instances
180 Oracle Corporation
<communicationParameter>
<label>AMS_PASSWORD</label>
<value>
<value>asap_1</value>
</value>
<description>AMS Password</description>
<deviceName>COMMON_DEVICE_CFG</deviceName>
<lineType>TELNET_CONNECTION</lineType>
</communicationParameter>
<communicationParameter>
<label>AMS_TID</label>
<value>
<value>PSALIDI-MINI</value>
</value>
<description>AMS Target ID</description>
<deviceName>COMMON_DEVICE_CFG</deviceName>
<lineType>TELNET_CONNECTION</lineType>
</communicationParameter>
<communicationParameter>
<label>AMS_UID</label>
<value>
<value>SUPERUSER</value>
</value>
<description>AMS user ID</description>
<deviceName>COMMON_DEVICE_CFG</deviceName>
<lineType>TELNET_CONNECTION</lineType>
</communicationParameter>
<communicationParameter>
<label>AMS_CTAG</label>
<value>
<value>1</value>
</value>
<description>AMS CTAG value</description>
<deviceName>COMMON_DEVICE_CFG</deviceName>
<lineType>TELNET_CONNECTION</lineType>
</communicationParameter>
Extracting source files
Alcatel A1000 DSLAM SW4.7 Cartridge Guide 181
<communicationParameter>
<label>AMS_PID</label>
<value>
<value>ANS#150</value>
</value>
<description>AMS PID value</description>
<deviceName>COMMON_DEVICE_CFG</deviceName>
<lineType>TELNET_CONNECTION</lineType>
</communicationParameter>
</element>
</activationConfig>
Extracting source filesBefore you can access an XML file to modify it, you must extract it from the .sar file. Use the following procedure to extract source files from the sar file. (Use Studio help for more information).
To extract source files
1. Create a repository directory. Copy the .sar file to the new directory and un-jar the sar file.
2. After you un-jar the sar file, you can access the XML files.
Loading a new XML fileWhen you finish modifying an XML file, you must create a new sar file, then restart the cartridge using the new file.
Follow the instructions in “Testing the installation” on page 13, for directions on how to load a new XML file. (Use Studio help for more information).
Chapter 5: Configuring ASAP to Support Additional NE Instances
182 Oracle Corporation