www.lanzar.com

u s e r ’ s m a n u a l

OptiX-2BOptiX-2B 2-Way Electronic Crossover Networkw/Remote Bass Boost and Level Control

Congratulations on your purchase of a new Lanzar Opti signal processor. Opti mobile electronics are some of the most advanced

car audio products available. These quality audio products are designed and engineered to afford you years of uncompromising

musical service. Lanzar has utilized the latest electronic technologies in order to deliver a superb listening experience.

The X-2B Active Crossover offers the listener the ability to enjoy the finest in mobile audio. The X-2B unleashes the effortless,

natural and open quality of the real performance. Car audio systems which utilize passive crossovers feed the music through

chokes and capacitors, which creates a “bottleneck” through which the music must pass. Portions of the program material may

pass through at different speeds, creating distortion – some of the music doesn’t make it through at all!

With the Lanzar Opti X-2B you’ll hear all the dynamics in the bass, and still hear delicacies like fingers sliding across guitar

strings.The X-2B also allows the user to group amplifiers and separate speakers in discrete assemblages so they play as one

cohesive unit, in harmony with each other. The X-2B becomes the music conductor in the system, balancing volume, assigning

the proper part of the music to a specific instrument, delaying some sounds so they reach your ear just as the rest of the music

does, with the sole purpose of creating the illusion that there is only the music.

I N T R O D U C T I O N . . .

general features

precautions

features and specifications

system wiring

mounting and installation

noise check and system adjustment

troubleshooting

2

3

4-5

6

7

8

9

t a b l e o f c o n t e n t s

2

g e n e r a l f e a t u r e s

Blue light illuminated control panelRotary control knobs12dB per octave crossover slopesPWM power supplyRemote bass boost (0-+18dB) and level controlsSubwoofer mode switchFrequency multiplier (x1, x10 high-pass crossover)Variable high-pass frequency control 40-8 kHzLeft and right high pass phase shift control (0-180)High-pass level controlFrequency multiplier (x1, x10 subwoofer crossover)Parametric "Q" control (2-20)Variable subwoofer frequency control 40-8 kHzVariable subwoofer bass boost frequency control 25-250 HzSubwoofer level controlSubwoofer stereo/mono mode controlSub & High RCA inputsLine out portSub & high pass outputsMax Variable output level controls, 7 volts

3

P r e c a u t i o n s

To prevent short circuits, be sure to disconnect the negative battery ground lead before wiring the system up.

When you finish the installation, be sure to make one more check to be sure everything is done correctly.

Reinstate all car parts that were removed.

Reconnect the negative battery ground lead.

4

f e a t u r e s a n d s p e c i f i c a t i o n s

5

f e a t u r e s a n d s p e c i f i c a t i o n sAdjustable Bass Boost

Frequency Adjustable Bass Boost

Adjustable Q Control Selectable Crossover

Frequency -High Pass

-Subwoofer (Low Pass) Power Supply

Input Impedance S/N ratio

Slope RateMax Output Signal Level

Channel Separation Distortion

Dimensions,WxDxH,inches(millimeters)

25Hz-250Hz

0-18dB

2-20

40Hz-8KHz

40Hz-8KHz

10-16V DC, negative ground

10K Ohm

more than 85dB

12dB/Octave

7.0V RMS

60dB

less than 0.05%

6x11-11/16x1-3/4

(150 x 297 x 45)

1. BASS BOOST CONTROL

2. BASS BOOST LEVEL CONTROL

3. SUBWOOFER MODE SWITCH

4. FREQUENCY MULTIPLIER (x1/x10 HIGH-PASS CROSSOVER)

5. VARIABLE HIGH-PASS FREQUENCYCONTROL 40-8KHz

6. LEFT AND RIGHT HIGH PASS PHASE SHIFTCONTROL 0-180

7. HIGH-PASS OUTPUT LEVEL CONTROL

8. FREQUENCY MULTIPLIER (x1/x10SUBWOOFER CROSSOVER)

9. PARAMETER "Q" CONTROL 2-20

10. VARIABLE SUBWOOFER FREQUENCYCONTROL 40Hz-8KHz

11. VARIABLE SUBWOOFER BASS BOOSTFREQUENCY CONTROL 25Hz-250Hz

12. SUBWOOFER OUTPUT LEVEL CONTROL

13. SUBWOOFER STEREO/MONO MODECONTROL

14. SUBWOOFER INPUT PORT

15. HIGH-PASS INPUT PORT

16. LINE OUT PORT

17. SUBWOOFER OUTPUT PORT

18. HIGH-PASS OUTPUT PORT

19. REMOTE CONTROL JACK

20. POWER TERMINALS

This control adjusts the bass boost gain (0 to +18dB).

This control sets the subwoofer gain control.

Allows subwoofer mode channel to receive signal from either the mix of from low-pass inputsdirectly (when head unit has appropriate 5ch/6ch outputs).

This switch changes crossover points from 40Hz-800Hz to 400Hz-8KHz for high frequency highchannel drivers.

By turning the selector you can choose the high-pass crossover points from 40Hz-8KHz.

Allows you to change the phase of your high-pass crossover from 0 to 180 degrees to helpcompensate for timing difference between drivers.

For adjusting the high pass channel output level.

This switch changes crossover points from 40Hz-800Hz to 400Hz-8KHz for high frequencysubwoofer channel drivers.

Allows independent continuous change of the boost frequency bandwidth (Q-factor) for each bandfrom Q=20 (Narrow bandwidth, steep slope) to Q=2 (Wide bandwidth, gentle slope).

By turning the selector you can choose the subwoofer crossover points from 40Hz-8KHz.

By turning the selector you can choose the subwoofer crossover bass boost points from 25Hz-250Hz.

For adjusting the subwoofer channel output level.

For selection of stereo or mono mode subwoofer output.

To be connected to the subwoofer outputs of the source unit.

To be connected to the outputs of the source unit.

To input additional amplifiers, crossover or Audio system.

To be connected to the subwoofer channel amplifier left/right inputs.

To be connected to the front channel amplifier left/right inputs.

Plug the modular telephone style cord connected to the remote control unit into this jack.

Use these connectors to deliver power, ground, and remote turn-on control to the unit.

REMOTE CONTROL UNIT1.BASS BOOST

This control sets the Bass Boost Gain from 0 to +18dB.

2.BASS LEVELThis control sets the subwoofer level control.

6

S y s t e m w i r i n g

Subwoofer mode switch: allows sub-woofer mode channel to receive signalfrom either, the mix of from front inputs, the direct from rear inputs.

SUB MODE SELECTORSWITCHPOSITIONDIRECT

MIX

VIA INPUTSOURCEFRONTREARFRONTREAR

OUTPUTSUBWOOFEROFFONONOFF

7

M o u n t i n g a n d i n s t a l l a t i o nYour new Opti Series Crossover comes complete with all required mounting hardware.

Mark the location for the mounting screw holes by positioning the Crossover where you wish to installit and use a scribe (or one of the mounting screws) inserted in each of the mounting holes to mark themounting surface. If the mounting surface is carpeted, measure the hole centers and mark with a felttip pen.

Before attempting to drill the mounting holes, take note of any wires, lines or other devices in yourvehicle which may be located behind the mounting surface! Then drill pilot in the mounting surfacefor the mounting screws and insert then. Tighten the screws securely.

• A red 18 gauge stranded or heavier and insulated wire should be connected to the terminal marked +12V. Wire an in-line fuse holder on this lead as it is the 12 Volts DC wire for the system. This wire shouldbe connected to your vehicle’s battery. If a wire is run directly to the battery make sure to install an in-line fuse on this wire within 12” from the battery.

• A black stranded wire of at least 18 gauge should be connected to the terminal marked Ground. This isthe ground wire for the X-2B and should be attached to the same ground point with the amplifiers in thesystem. Keeping this ground wire as short as possible improves the electrical circuit and keeps groundrelated noise problems to a minimum.

• An orange stranded wire of a least 20 gauge should be connected to the terminal marked Remote. Thiswire connects to your head unit’s remote out or power antenna lead out. This wire should supply 12 VoltsDC any time the radio, cd or cassette are playing. This lead must also be connected to any other componentsin your system that utilize a remote turn-on lead for powering up.

• Connect all line inputs and outputs using high-quality RCA-RCA cables.

• Recheck all connections before powering up.

• Set all level controls to their least sensitive positions and set all crossover controls, switches, etc. to thedesired frequency or position.

• Once the system is powered up, set the volume control on the head unit to about the 2 o'clock position,and then set all the amplifiers' level controls for half output level.

Installation

8

N o i s e c h e c k a n d s y s t e m a d j u s t m e n tNOISE CHECKCheck the entire audio system for noise before permanently securing the CROSSOVER mounting

1. Start the engine.2. Turn the audio system on.3. Rev the engine and vary the VOLUME of the audio system to determine if there is any unwanted noise.

If so, turn both the audio system and the engine off. Do not secure the CROSSOVER mounting screws. Refer to the "Trouble Shooting Guide" at thismanual.

4. If the audio system does not have any noise, securely tighten the CROSSOVER mounting screw and double check the wiring cables for safe placement.

SYSTEM ADJUSTMENTPreliminary AdjustmentsPre-setting the system provides a necessary starting point for fine-tuning the entire audio system to maximum performance.NOTE: DO NOT MOUNT CROSSOVER UNTIL THE FOLLOWING PROCEDURES HAVE BEEN COMPLETED.

1. Preset each amplifier input gain adjustment at the amplifier to half of maximum.2. Before turning the audio system on, preset-adjust the high and sub-woofer output level controls.3. Slowly turn the volume up and listen carefully for: obvious trouble in sound (distortion, no sound, no hiss, total silence). Turn the system off refer to

"Trouble Shooting Guide" at this manual.

CautionDO NOT ROUTE AUDIO CABLES AND POWER CABLES TOGETHER! THIS CAN CAUSE ENGINE NOISE IN YOUR AUDIO SYSTEM.ALWAYS DISCONNECT THE SYSTEM FROM THE BATTERY BEFORE ATTEMPTING TO MAKE OR ALTER ANY CONNECTIONS. THISPRODUCT IS DESIRED FOR USE IN ANY 12 VOLTS NEGATIVE GROUND ELECTRICAL SYSTEM ONLY. INSTALLING THIS PRODUCTIN ANY POSITIVE GROUND ELECTRICAL SYSTEM COULD SERIOUSLY DAMAGE THE AUDIO SYSTEM.

1. There is an audible distortion at a lowvolume level.

PROBLEM POSSIBLE CAUSE

• Output levels NOT set correctly.• Crossover frequencies NOT set correctly.• Check for shorts on the speaker leads.

2. A whining sound can be heard through thespeakers when the audio system is at lowvolume with the engine running. The whiningnoise remains unchanged or seems todisappear when the volume level isincreased.

3. There is a "motor boating" type of soundwhen the engine is running and the audiosystem volume is set at a reasonably highlevel.

• Check the red power wire. It muse beconnected directly to the battery.

• Check the system's ground point It musemake good contact with chassis ground(bare metal).

• The radio and the CROSSOVER must begrounded at the same reference point.

• Check the red power wire. It must beconnected directly to the battery.

• Check the system's ground point. It mustmake good contact with chassis ground(bare metal).

9

T B O U B L E S H O O T I N G G U I D E

4. High squeal noise from speakers • This is almost always caused by a poorly -grounded RCA patch cord.

All Lanzar Signal Processors are carefully constructed and thoroughly testedbefore shipment. Units purchased in the USA are warranted to be free of defectsin material and workmanship for three (3) years from the date of purchase. Thiswarranty is limited to the original retail purchaser of the Signal Processor.

Should the unit fail due to a factory defect in material or workmanship, your unitwill be repaired or replaced at the sole discretion of Lanzar.

To obtain warranty service, you must first call our Consumer Return Hotlinenumber at (718) 236-6948 to obtain a Return Authorization (RA) number. ThisRA Number must appear on the outside of your package and on all paperworkrelating to your return.

When returning the unit to us for warranty service, it must be carefully packedand shipped prepaid to:

You must also include the following items with your return:• A copy of your sales receipt or other proof of purchase• A brief letter indicating the problem you are experiencing with the

product• Include in your letter your return address, daytime phone number

and RA Number• Also include a check or money order for $20.00 for return shipping,

handling and insurance, or provide your VISA/MasterCard numberwith expiration date.

Our obligation under this warranty is limited to the repair or replacementof the defective unit when it is returned to us prepaid. This warranty willbe considered void if the unit was tampered with, improperly serviced,or subject to misuse, neglect or accidental damage.

All implied warranties of merchantability and fitness for a particularpurpose are limited in duration to the length of the warranty. Lanzarexpressly disclaims any liability for incidental or consequential damagescaused by product defects. This warranty does not cover any expenseincurred in the removal and/or reinstallation of the Signal Processor.Lanzar’s total liability will not exceed the purchase price of the SignalProcessor.

Some states do not allow the exclusion or limitation of incidental orconsequential damages, or limitations on how long an implied warrantylasts, so the above limitations and exclusions may not apply to you.This warranty gives you specific legal rights, and you may also haveother rights which vary from state to state.

R.A. # ______________Lanzar Service Center1600 63rd StreetBrooklyn, NY 11204

l i m i t e d w a r r a n t y p o l i c y

w w w . l a n z a r . c o m

C r o s s o v e r