OPERATOR'S MANUAL CRRFr HRH - managemylife.com · OPERATOR'S MANUAL CRRFr HRH ° ... To remove the...

6
OPERATOR'S MANUAL CRRFr HRH ° 2-DRAWER BB - MIDDLE CHEST \\ \\\\\\ \ CALL 1-800-4MY=HOME OR (1=800-469=4663) FOR SERVICE PARTS. Refer to Service Parts Drawing for full listing of Service Parts. LOCATING MODEL # iNFORMATiON Model numbers and other information required for service parts is located on a label on the interior right side of the top most drawer. • The maximum weight for each drawer should be no more than 30 pounds. • Empty weight of the unit is 33 Ibs. • The maximum product weight, including contents, should be no more than 125 pounds. • Lubricate the slides with grease or equivalent, (twice yearly.) • Lubricate lock with graphite, (yearly). • Periodically the drawer fronts, drawer trim, and other surfaces should be cleaned with a mild detergent and water. • Auto wax will preserve the unit's luster finish. Apply the wax as to a car. The wax will also help protect the unit against scratch- es. • Grease and oil can be removed with most standard cleaning fluids. For safety, use a nonflammable cleaning fluid. • If drawer liners are supplied, it is recommended they are used to protect the finish inside the drawers and to make the drawers easier to clean. The drawer liners may be cleaned with soap and water. DANGER ,_ is used to indicate a hazardous situation which, if not avoided, wil__!l result in serious injury or death. WARNING /ix indicates a hazardous situation which, if not avoided, could result in serious injury or death. CAUTIONis used to indicate a hazardous situation which, if not avoided, _ result in minor injury, moderate injury, or property damage. CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. DANGER A, • DO NOT stand on this product. You may fall or cause product to tip. • DO NOT open more than one drawer. The product may become unstable and tip. • DO NOT step in the drawers. You may fall or cause product to tip. • DO NOT mount this product on a truck bed or any other moving object. • DO NOT move the product prior to closing and locking all the drawers. The drawers could come open and make the product unstable and tip. WARNING z_ • WEAR SAFETY GLASSES when removing or repositioning the slides. • DO NOT pull this product when moving it. Push the product to prevent personal injury. • USE THE BRAKES when not moving this product. This will prevent the product from rolling. • DO NOT alter this product in any manner. For example, do not weld external Iockbars or attach electrical equipment. • Keep the product on level surfaces. The product may become unstable and tip if stored or moved on an uneven surface. • BE CAREFUL when closing the cover. Remove hands before the cover closes completely. CAUTION This product is not designed to be directly lifted with a fork lift, or to be towed with any mechanical devices. • The maximum weight for each drawer should never be exceed- ed. • Only transport this product empty. Properly secure when trans- porting. • DO NOT exceed maximum product weight, including contents. See Operations Sections: Capacities for more information. Ball bearing slides Distributed by Sears Brands Management Corporation, Hoffman Estates, IL 60179 Rev C F1818

Transcript of OPERATOR'S MANUAL CRRFr HRH - managemylife.com · OPERATOR'S MANUAL CRRFr HRH ° ... To remove the...

Page 1: OPERATOR'S MANUAL CRRFr HRH - managemylife.com · OPERATOR'S MANUAL CRRFr HRH ° ... To remove the slide from the unit, first remove the drawer. After removing the drawers drill out

OPERATOR'S MANUAL

CRRFr HRH °

2-DRAWER BB - MIDDLE CHEST

\\

\\\\\\

\

CALL 1-800-4MY=HOME OR (1=800-469=4663) FOR SERVICEPARTS. Refer to Service Parts Drawing for full listing of ServiceParts.

LOCATING MODEL # iNFORMATiON

Model numbers and other information required for service parts islocated on a label on the interior right side of the top most drawer.

• The maximum weight for each drawer should be no more than30 pounds.

• Empty weight of the unit is 33 Ibs.• The maximum product weight, including contents, should be no

more than 125 pounds.

• Lubricate the slides with grease or equivalent, (twice yearly.)

• Lubricate lock with graphite, (yearly).• Periodically the drawer fronts, drawer trim, and other surfaces

should be cleaned with a mild detergent and water.

• Auto wax will preserve the unit's luster finish. Apply the wax asto a car. The wax will also help protect the unit against scratch-es.

• Grease and oil can be removed with most standard cleaningfluids. For safety, use a nonflammable cleaning fluid.

• If drawer liners are supplied, it is recommended they are usedto protect the finish inside the drawers and to make the drawerseasier to clean. The drawer liners may be cleaned with soap andwater.

DANGER ,_ is used to indicate a hazardous situation which,

if not avoided, wil__!lresult in serious injury or death.WARNING /ix indicates a hazardous situation which, if not

avoided, could result in serious injury or death.CAUTIONis used to indicate a hazardous situation which, if not

avoided, _ result in minor injury, moderate injury, or propertydamage.

CAUTION: Read and follow all Safety Rules and OperatingInstructions before first use of this product.

DANGER A,

• DO NOT stand on this product. You may fall or cause product totip.

• DO NOT open more than one drawer. The product may becomeunstable and tip.

• DO NOT step in the drawers. You may fall or cause product totip.

• DO NOT mount this product on a truck bed or any other movingobject.

• DO NOT move the product prior to closing and locking all thedrawers. The drawers could come open and make the productunstable and tip.

WARNING z_• WEAR SAFETY GLASSES when removing or repositioning the

slides.

• DO NOT pull this product when moving it. Push the product toprevent personal injury.

• USE THE BRAKES when not moving this product. This willprevent the product from rolling.

• DO NOT alter this product in any manner. For example, do notweld external Iockbars or attach electrical equipment.

• Keep the product on level surfaces. The product may becomeunstable and tip if stored or moved on an uneven surface.

• BE CAREFUL when closing the cover. Remove hands beforethe cover closes completely.

CAUTION

This product is not designed to be directly lifted with a fork lift, orto be towed with any mechanical devices.

• The maximum weight for each drawer should never be exceed-ed.

• Only transport this product empty. Properly secure when trans-porting.

• DO NOT exceed maximum product weight, including contents.See Operations Sections: Capacities for more information.

Ball bearing slides

Distributed by Sears Brands Management Corporation, Hoffman Estates, IL 60179 Rev C F1818

Page 2: OPERATOR'S MANUAL CRRFr HRH - managemylife.com · OPERATOR'S MANUAL CRRFr HRH ° ... To remove the slide from the unit, first remove the drawer. After removing the drawers drill out

Tools Required:3/8 inch wrench5!16=inch dritt bit

HARDWARE INCLUDED:

1/4 =20 x 5/8-in (Qty: 4)

0" _± O

NOTE: Not att operation instructions wilt relate to your model.

TO LOCK INTERMEDIATE CHEST

The Iockbar for the intermediate chest is stored in the

top drawer.

Process:[} Insert the lockbar into the slot in the base.[}Move the tockbar toward the unit until the bent end fits

into the slot near the lock.

[} Lock with the key.

1/4 =20 Nut (Qty: 4)

intermediate Chest:Literature

Hardware bag

_, V, t,

TO ATTACH CHEST

Process:

Remove enough drawers to access the top and bottommounting surfaces of the units. Refer to drawer removalinstructions.

Place the chest in the desired location on top of thecabinet and mark the mounting hole locations onto thecabinet top.Remove the chest and drill two 5/16" (8mm) holesthrough the top of the cabinet.Secure the units together using (2) 1/4 - 20 x 5/8" screwand (2) 1/4 - 20 nut at each joint. The hardware is pro-vided in the bag located with the unit.

TO UNLOCK INTERMEDIATE CHEST

[}Reverse above procedure.

REMOVING DRAWERS

- Empty the drawer.Fully extend the drawer.

Release

Lever Style = Lift or lower (depending on the slide) therelease lever on both sides, (this allows the slides to rideover the stops.) Putt out to remove.

Page 3: OPERATOR'S MANUAL CRRFr HRH - managemylife.com · OPERATOR'S MANUAL CRRFr HRH ° ... To remove the slide from the unit, first remove the drawer. After removing the drawers drill out

INSTALLINGDRAWERS

Ballbearingslide=Puttslidesandslidecarrierouttofullyextendedposition(seeillustration.)Holdtheslideonthecabinetwhilealigningitwiththeslideondrawer.Slightlyinsertonesideandrepeatfortheotherside.Slowlypushdrawertoitsfullyclosedpositiontoengageslide.Opendrawerandrectosetoensureproperoperation.

slidecarrier

/

slide

I/

REMOVING AND INSTALLING SLIDES

To remove the slide from the unit, first remove thedrawer.

After removing the drawers drill out the rivets, use a5/32=in drill bit. The rivets will need to be replaced.To reinstall the slide, place the slide in the appropriateposition in the unit and putt toward the front of the unit.Replace rivets to secure slide to the unit.For smooth operation, make sure the drawers arematched with their original slides.

\\

\\

\

Page 4: OPERATOR'S MANUAL CRRFr HRH - managemylife.com · OPERATOR'S MANUAL CRRFr HRH ° ... To remove the slide from the unit, first remove the drawer. After removing the drawers drill out

MANUAL DE USUARIO

®

MEDIC - 2-CAJONE BB BAOL

\\\\\\\\\

\

EN ESTADOS UNIDOS LLAME AL 1-800-659-7084 PARAPIEZAS DE REPUESTO. FUERA DE ESTADOS UNIDOSLLAME A SU DISTRIBUIDOR LOCAL. Suministre et n(_mero demodeto al comunicarse.

UBICACK)N DE INFORMACION DEL NO. DE MODELO

Et n_mero de modeto y demos informaci0n requerida para las pie-zas de servicio se encuentran en una etiqueta en et tado interiorderecho de ta gaveta superior.

Et peso m_ximo en cada gaveta no debe set mayor de 13,6 kgEt peso vacio de la unidad es15 kg.The maximum product weight, including contents, should be nomore than 56,8 kg.

Lubrique tas guias con grasa o equivalente (dos veces pot ado).Lubrique ta cerradura con grafito (anualmente).

Limpie con detergente suave y agua los frontates y los bordestaterales de los cajones y las demos superficies.La cera para autom0viles preservar_ et acabado bdltoso de taunidad. Aplique ta cera como Io hada at carro. La cera tambiOnayudar_ a proteger la unidad contra raspones.La grasa y et aceite pueden retirarse con ta mayoda de los tiqui-dos est_ndar para limpieza. Por razones de seguddad, utitice untiquido incombustible para timpieza.Si se suministran forros para las gavetas, se recomienda que seutilicen para proteger el acabado intemo de las mismas y parafacilitar ta timpieza. Los forros para gavetas pueden timpiarsecon agua y jab0n.

PELIGRO ,_ se utitiza para indicar una situaci0n petigrosa

que, de no evitarse, resuttar_ en tesiones graves o ta muerte.ADVERTENOIA z_ indica una situaci0n peligrosa que, deno evitarse, podda producir tesiones graves o la muerte.PREOAUOION se utiliza para indicar una situaci0n petigrosa que,de no evitarse, puede derivar en tesiones teves o moderadas, oen da_o a ta propiedad.

ATENCION: Lea y siga todas tas Normas de Seguridad y tasInstrucciones de Funcionamiento antes de utitizar pot primera vezeste producto.

PELIGRO ,_

- NO se ponga de pie sobre esta unidad. Puede caerse u oca=sionar que el producto se vuetque.NO abra m_s de una gaveta. Et producto podda quedar in=estabte y volcarse.NO utitice tas gavetas como petda_os. Puede caerse u oca=sionar que el producto se vuetque.NO monte este producto en una cama de carro o ninguin ottoobjeto m0vil.

• NO mueva ta unidad antes de cerrar y asegurar todas las gave=tas. Las gavetas poddan abrirse y hacer que ta unidad se vuetvainestabte y se vuetque.

ADVERTENCIA A

- USE GAFAS DE SEGURIDAD at quitar o volver a poner tascorrederas.

NO hate ta unidad, emp_jeta cuando la mueva.UTILICE LOS FRENOS cuando et producto no est6 en mov-imiento. Esto impedir_ que se deslice.NO attere la unidad en modo alguno. Pot ejempto, no suelde tasbarras de sujeci0n extemas nile incorpore equipos etOctricos.Mantenga ta unidad en superficies niveladas. La unidad puedetomarse inestable y votcarse si se almacena o se movitiza enuna superficie no nivelada.TENGA cuidado cuando cierre ta tapa. Quite tas manos antesde que ta tapa cierre comptetamente.

PRECAUCION

- Este producto no est_ diseSado para set tevantado directa=mente con un montacargas, ni para set remolcado con uni-dades mecanizadas.

Nunca debe exceder el peso m_ximo de cada gaveta.S0to transporte esta unidad cuando est6 vacia. Aseg(_reta adec-uadamente cuando la transporte.NO exceda el peso m_ximo det producto, incluyendo et conteni-do. RefiOrase a tas Capacidades para m_s informaci0n.

Distributed by Sears Brands Management Corporation, Hoffman Estates, IL 60179 Rev C F1818

Page 5: OPERATOR'S MANUAL CRRFr HRH - managemylife.com · OPERATOR'S MANUAL CRRFr HRH ° ... To remove the slide from the unit, first remove the drawer. After removing the drawers drill out

HERRAMIENTAS NECESARIAS:

Llave Ingtesa de 10ramBroca de 5/16 de puJgada

PIEZAS INCLUIDAS:

1/4 - 20 x 5!8qn TorniHo (Qty: 4)

1/4 - 20 Tuerca (Qty: 4)

NOTA: No todas tas instrucciones de uso se refieren atu modeto.

PARA ASEGURAR LA CAJA PORTAHERRAMIENTAS

[;Compruebe que tas gavetas est6n comptetamente cer-radas.

[; Introduzca Ja barra de bJoqueo (que se guarda en labande]a superior), con el extremo que tbne la tengQetahacia arriba, dentro de Jaabertura en ta bande]a superiory bajando hasta entrar en ta abertura en ta base.

[;Cierre ta tapa y asegQreta con ta Have.

COMO DESBLOQUEAR EL BAUL

[; Invierta et procedimiento de desbtoqueo.

BaOi:

Materiat impresoBoisa de accesorios

_ REMOCION DE GAVETAS- Vade Ja gaveta.

- Abra comptetamente ta gaveta.

Libere

FIJACION DEL BAUL:

PrOCeSO:

- Saca las gavetas necesanas para poder atcanzar ettope y el rondo de tas superficies de montaje de tasunidades. Consutta tas instrucciones para sacar tasgavetas.

- Coloca et ba0t en et sitio elegido encima del gabinete ymarca los orificios de montaje en et tope del gabinete.

- Quite et baul y tatadre dos 5/16" agujeros (de 8 mm)pot la cumbre del gabinete.

- Fija las unidades en cada union con (2) tornittos 1/4- 20 x 5/8" y (2) tuercas 1/4 - 20. Los herrajes seencuentran en una bolsa inctuida con ta unidad

Estilo pa_anca - Levante o baje (dependiendo de lacorredera) ta palanca de liberaciOn en ambos lados (estopermite que las correderas pasen sobre tos topes.) Jatehacia afuera para retirar.

Page 6: OPERATOR'S MANUAL CRRFr HRH - managemylife.com · OPERATOR'S MANUAL CRRFr HRH ° ... To remove the slide from the unit, first remove the drawer. After removing the drawers drill out

INSTALACtONDEGAVETASCorrederasderodamientosesfedcos° hate hacia

afuera Jas correderas y el soporte de las correderas hastaque queden en posiciOn totalmente extendida (vet iJus-traciOn). Sostenga ta corredera en et gabinete mientras toatinea con ta corredera de ta gaveta.

Soporte de las correderas

/........................... 0

Corredera

INSTALACtON Y DESINSTALCI6N DE CORREDERAS

Para quitar Jacorredera de ta unidad, primero quite tagaveta.Despues de retirar las gavetas tatadrar bs remaches,utilice una broca de 5/32-in. Los remaches necesitaran

ser reemplazadosPara volver a instalar ta corredera, ponga Jacorrederaen Ja posiciOn correcta en la unidad. Tire de etla hacia laparte deJantera de la unidad. Reemplace Jos remachespara asegurar Jacorredera en Ja unidad.Para JaoperaciOn tisa, cerciOrese de que los cajones es-t6n correspondidos con con sus diapositivas originates.

jJ

Saca el remachecon el taladro