OPERATING INSTRUCTIONS OPERATOR’S MANUAL

8.914-405.0

OPERATING INSTRUCTIONS AND PARTS MANUAL

900/1400GAS-FIRED SERIES

OPERATOR’S MANUAL

FOR TECHNICAL ASSISTANCE OR THE HOTSY DEALER NEAREST YOU, CONSULT OUR WEB PAGE AT WWW.HOTSY.COM

®cLISTED ®

89144050-1

952SS-208 SPECIFICATIONS● Pump Volume At Pump Head: 3.8 GPM/228 GPH● Pump Pressure At Pump Head: 2300 PSI● Burner Type: Natural Gas Fired, 364,835 BTU/Hr.● Motor Hp: 6.2● Machine Voltage: 208Vac/60Hz/1Ph● Total Machine Amperage: 28 Amps● Machine Weight: 500 Lbs.● Shipping Weight: 560 Lbs.● Exhaust Stack Size: 8"● Machine Dimensions: Length=45", Width=18",

Height=50"

969SS SPECIFICATIONS● Pump Volume At Pump Head: 3.8 GPM/228 GPH● Pump Pressure At Pump Head: 2300 PSI● Burner Type: Natural Gas Fired, 364,835 BTU/Hr.● Motor Hp: 6.2● Machine Voltage: 575Vac/60Hz/3Ph● Total Machine Amperage: 7 Amps● Machine Weight: 495 Lbs.● Shipping Weight: 550 Lbs.● Exhaust Stack Size: 8"● Machine Dimensions: Length=45", Width=18",

Height=50"

981SS SPECIFICATIONS● Pump Volume At Pump Head: 3.9 GPM/234 GPH● Pump Pressure At Pump Head: 2000 PSI● Burner Type: LP Gas Fired, 360,997 BTU/Hr.● Motor Hp: 5.0● Machine Voltage: 230VAC/60Hz/1Ph● Total Machine Amperage: 25 Amps● Machine Weight: 490 Lbs.● Shipping Weight: 550 Lbs.● Exhaust Stack Size: 8"● Machine Dimensions: Length=45", Width=18",

Height=50"


Height=50"

991SS SPECIFICATIONS● Pump Volume At Pump Head: 3.9 GPM/234 GPH● Pump Pressure At Pump Head: 2000 PSI● Burner Type: LP Gas Fired, 364,835 BTU/Hr.● Motor Hp: 5.0● Machine Voltage: 230Vac/60Hz/3Ph● Total Machine Amperage: 16 Amps● Machine Weight: 485 Lbs.● Shipping Weight: 545 Lbs.● Exhaust Stack Size: 8"● Machine Dimensions: Length=45", Width=18",

Height=50"

991SS-208 SPECIFICATIONS● Pump Volume At Pump Head: 3.9 GPM/234 GPH● Pump Pressure At Pump Head: 2000 PSI● Burner Type: LP Gas Fired, 360,997 BTU/Hr.● Motor Hp: 5.0● Machine Voltage: 208Vac/60Hz/3Ph● Total Machine Amperage: 18 Amps● Machine Weight: 485 Lbs.● Shipping Weight: 545 Lbs.● Exhaust Stack Size: 8"● Machine Dimensions: Length=45", Width=18",

Height=50"


Height=50"

992SS-208 SPECIFICATIONS● Pump Volume At Pump Head: 3.9 GPM/234 GPH● Pump Pressure At Pump Head: 2000 PSI● Burner Type: Natural Gas Fired, 364,835 BTU/Hr.● Motor Hp: 5.0● Machine Voltage: 208Vac/60Hz/3Ph● Total Machine Amperage: 18 Amps● Machine Weight: 485 Lbs.● Shipping Weight: 545 Lbs.● Exhaust Stack Size: 8"● Machine Dimensions: Length=45", Width=18",

Height=50"


Height=50"


Height=50"


Height=50"

1412SS SPECIFICATIONS● Pump Volume At Pump Head: 3.9 GPM/234 GPH● Pump Pressure At Pump Head: 3000 PSI● Burner Type: Natural Gas Fired, 364,835 BTU/Hr.● Motor Hp: 7.5● Machine Voltage: 230VAC/60Hz/1Ph● Total Machine Amperage: 34 Amps● Machine Weight: 550 Lbs.● Shipping Weight: 610 Lbs.● Exhaust Stack Size: 8"● Machine Dimensions: Length=45", Width=18",

Height=50"


Height=50"

1421SS-208 SPECIFICATIONS● Pump Volume At Pump Head: 3.9 GPM/234 GPH● Pump Pressure At Pump Head: 3000 PSI● Burner Type: LP Gas Fired, 360,997 BTU/Hr.● Motor Hp: 7.5● Machine Voltage: 208VAC/60Hz/3Ph● Total Machine Amperage: 24 Amps● Machine Weight: 545 Lbs.● Shipping Weight: 605 Lbs.● Exhaust Stack Size: 8"● Machine Dimensions: Length=45", Width=18",

Height=50"


Height=50"

1422SS-208 SPECIFICATIONS● Pump Volume At Pump Head: 3.9 GPM/234 GPH● Pump Pressure At Pump Head: 3000 PSI● Burner Type: Natural Gas Fired, 364,835 BTU/Hr.● Motor Hp: 7.5● Machine Voltage: 208Vac/60Hz/3Ph● Total Machine Amperage: 24 Amps● Machine Weight: 545 Lbs.● Shipping Weight: 605 Lbs.● Exhaust Stack Size: 8"● Machine Dimensions: Length=45", Width=18", Height=50"

1424SS SPECIFICATIONS● Pump Volume At Pump Head: 3.9 GPM/234 GPH● Pump Pressure At Pump Head: 3000 PSI● Burner Type: LP Gas Fired, 360,997 BTU/Hr.● Motor Hp: 7.5● Machine Voltage: 460Vac/60Hz/3Ph● Total Machine Amperage: 12 Amps● Machine Weight: 545 Lbs.● Shipping Weight: 605 Lbs.● Exhaust Stack Size: 8"● Machine Dimensions: Length=45", Width=18",

Height=50"


Height=50"

1452SS-208 SPECIFICATIONS● Pump Volume At Pump Head: 3.9 GPM/234 GPH● Pump Pressure At Pump Head: 3000 PSI● Burner Type: Natural Gas Fired, 364,835 BTU/Hr.● Motor Hp: 8.2● Machine Voltage: 208Vac/60Hz/1Ph● Total Machine Amperage: 36.5 Amps● Machine Weight: 555 Lbs.● Shipping Weight: 615 Lbs.● Exhaust Stack Size: 8"● Machine Dimensions: Length=45", Width=18", Height=50"

1469SS SPECIFICATIONS● Pump Volume At Pump Head: 3.9 GPM/234 GPH● Pump Pressure At Pump Head: 3000 PSI● Burner Type: Natural Gas Fired, 364,835 BTU/Hr.● Motor Hp: 8.2● Machine Voltage: 575Vac/60Hz/3Ph● Total Machine Amperage: 10 Amps● Machine Weight: 555 Lbs.● Shipping Weight: 615 Lbs.● Exhaust Stack Size: 8"● Machine Dimensions: Length=45", Width=18", Height=50"

5

CONTENTS

HOTSY • 900-1400 • 8.914-405.0 GAS FIRED • Rev. 9/11

Model Number ______________________________

Serial Number ______________________________

Date of Purchase ____________________________The model and serial numbers will be found on a decal attached to the pressure washer. You should record both serial number and date of purchase and keep in a safe place for future reference.

Introduction & Important Safety Information 6-8

Component Identification 9

Assembly Instructions 10

Installation Instructions 11-12

Operation Instructions 13-14

Shutdown Instructions 15

Storage 15

Maintenance 16

Troubleshooting 17-19

Exploded Views 20-21

Exploded View Parts List 22-23

Burner Assembly & Parts List 24-25

Pump Assembly & Parts List 26-27

Float Tank Assembly & Parts List 28-29

Control Panel & Parts List 30-31

Coil Outlet & Exploded View Parts List 32

Hose & Trigger Gun Assembly & Parts List 33

Specifications 34-35

MT Series Pump Exploded View & Parts List 36-37

VB9 Unloader Exploded View and Parts List 38

Wiring Diagrams 39-40

Warranty


OP

ER

AT

OR

’S M

AN

UA

L P

RE

SS

UR

E W

AS

HE

R

6

INTRODUCTION & IMPORTANT SAFETY INFORMATIONThank you for purchasing this Pressure Washer.

We reserve the right to make changes at any time without incurring any obligation.

Owner/User Responsibility:The owner and/or user must have an understanding of the manufacturer’s operating instructions and warnings before using this pressure washer. Warning information should be emphasized and understood. If the operator is not fluent in English, the manufacturer’s instructions and warnings shall be read to and discussed with the operator in the operator’s native language by the purchaser/owner, making sure that the operator com-prehends its contents.

Owner and/or user must study and maintain for future reference the manufacturers’ instructions.

The operator must know how to stop the machine quickly and understand the operation of all controls. Never permit anyone to operate the engine without proper instructions.

This manual should be considered a permanent part of the machine and should remain with it if machine is resold.

When ordering parts, please specify model and serial number. Use only identical replacement parts.

This machine is to be used only by trained operators.

IMPORTANT SAFETY INFORMATION

READ OPERATOR’S MANUAL THOROUGHLY

PRIOR TO USE.

WARNING: To reduce the risk of injury, read operating instruc-tions carefully before using.

1. Read the owner's manual thoroughly. Failure to follow instructions could cause mal-function of the machine and result in death, serious bodily injury and/or property dam-age.

2. Know how to stop the machine and bleed pressure quickly. Be thoroughly familiar with the controls.

3. Stay alert — watch what you are doing.

4. Do not replace LP tank while machine is running.

5. All installations must comply with local codes. Con-tact your electrician, plumber, utility company or the selling distributor for specific details. If your machine is rated 250 volts or less, single phase will be pro-vided with a ground fault circuit interrupter (GFCI). If rated more than 250 volts, or more than single phase this product should only be connected to a power supply receptacle protected by a GFCI.

DANGER: Improper connection of the equip-ment-grounding conductor can result in a risk of electrocution. Check with a qualified electrician or service personnel if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the product - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Do not use any type of adaptor with this product.

WARNING

KEEP WATER SPRAY AWAY FROM

ELECTRICAL WIRING.

WARNING: Keep wand, hose, and water spray away from electric wiring or fatal electric shock may result.

6. To protect the operator from electrical shock, the machine must be electrically grounded. It is the responsibility of the owner to connect this machine

to a UL grounded receptacle of proper voltage and amperage ratings. Do not spray water on or near electrical components. Do not touch machine with wet hands or while standing in water. Always dis-connect power before servicing.

RISK OF EXPLOSION: IF GAS SMELL

PRESENT TURN OFF SUPPLY

WARNING WARNING: Flammable liquids can create fumes which can ig-nite, causing property damage or severe injury.

WARNING: Risk of explosion — Operate only where open flame or torch is permitted.

RISK OF FIRE. DO NOT ADD FUEL WHEN OPERATING

MACHINE.

WARNING WARNING: Risk of fire — Do not change tanks when the product is operating or still hot.

WARNING: Use vapor fuel only.

7. Oil burning appliances shall be installed only in locations where combustible dusts and flammable gases or vapors are not present. Do not store or use gasoline near this ma-chine.

8. Keep operating area clear of all persons.

WARNING

USE PROTECTIVE EYE WEAR

AND CLOTHING WHEN OPERATING THIS EQUIPMENT.

WARNING: High pressure spray can cause paint chips or other particles to become airborne and fly at high speeds. To avoid personal injury, eye, hand and foot safety devices must be worn.

9. Eye, hand, and foot protection must be worn when using this equipment.


7

PR

ES

SU

RE

WA

SH

ER

OP

ER

AT

OR

’S M

AN

UA

L

WARNING

PROTECT FROM FREEZING

WARNING: Protect machine from freezing.

13. To keep machine in best operating conditions, it is important you protect machine from freezing. Failure to protect mach ine f rom f reez ing could cause malfunction of the machine and result in death,

serious bodily injury, and/or property damage. Fol-low storage instructions specified in this manual.

14. Inlet water must be clean fresh water and no hotter then 90°F.

WARNING

RISK OF ASPHYXIATION. USE THIS PRODUCT ONLY

IN A WELL VENTILATED AREA.

WARNING: Risk of asphyxiation. Use this product only in a well ventilated area.

15. Avoid installing machines in small areas or near exhaust fans. Adequate oxygen is needed for combustion or dangerous carbon monoxide will result.

16. Manufacturer will not be liable for any changes made to our standard machines or any components not purchased from us.

17. The best insurance against an accident is precau-tion and knowledge of the machine.

WARNING

RISK OF INJURY FROM FALLS WHEN

USING LADDER.

WARNING: Be extremely careful when using a ladder, scaffolding or any other relatively unstable location. The cleaning area should have adequate slopes and drainage to reduce the pos-sibility of a fall due to slippery surfaces.

18. Do not overreach or stand on unstable support. Keep good footing and balance at all times.

19. Do not operate this machine when fatigued or under the influence of alcohol, prescription medications, or drugs.

20. Follow the maintenance instructions specified in the manual.

21. Do not replace LP tank while machine is running. Serious injury could result.

WARNING: Use vapor fuel only.

22. The LP models are designed to run on vapor pro-pane fuel. Do not use liquid fuel. Have a qualified serviceman install and service your equipment.


WARNING

EAR PROTECTION MUST BE WORN

WARNING: This machine exceeds 85 db appropriate ear protection must be worn.

HOT DISCHARGE FLUID: DO NOT TOUCH OR DIRECT DISCHARGE

STREAM AT PERSONS.

CAUTION: Hot discharge fluid. Do not touch or direct discharge stream at persons.

WARNING: This machine pro-duces hot water and must have insulated components attached to protect the operator.

WARNING

RISK OF INJURY. HOT SURFACES

CAN CAUSE BURNS

WARNING: Risk of injury. Hot surfaces can cause burns. Use only designated gripping areas of spray gun and wand. Do not place hands or feet on non-insu-lated areas of the pressure washer.

10. To reduce the risk of injury, close supervision is

necessary when a machine is used near children. Do not allow children to operate the pressure washer. This machine must be attended during operation.

TRIGGER GUN KICKS BACK - HOLD WITH

BOTH HANDS

WARNING WARNING: Grip cleaning wand securely with both hands before starting. Failure to do this could result in injury from a whipping wand.

11. Never make adjustments on machine while in operation.

12. Be certain all quick coupler fit-tings are secured before using pressure washer.

RISK OF INJECTION OR SEVERE INJURY TO PERSONS. KEEP CLEAR OF NOZZLE.

WARNING WARNING: High pressure devel-oped by these machines will cause personal injury or equip-ment damage. Keep clear of nozzle. Use caution when oper-ating. Do not direct discharge stream at people, or severe in-jury or death will result.


OP

ER

AT

OR

’S M

AN

UA

L P

RE

SS

UR

E W

AS

HE

R

8

23. Never expose a spark or flame where there may be unburned gas present.

24. Install the machine 18” above the floor and about 2 feet from wall providing adequate ventilation and space.

25. When making repairs disconnect from electrical source and shut off gas valve.

26. Install this machine on non combustible flooring.

27. Do not allow acids, caustic or abrasive fluids to pass through the pump.

28. Never run pump dry or leave spray gun closed longer than 1-2 minutes.

WARNING: If connection is made to portable water supply, a back flow device must be provided.

Follow the maintenance instructions specified in the manual.


Example Of Down Draft DiverterFor Gas Fired

Machines


9

PR

ES

SU

RE

WA

SH

ER

OP

ER

AT

OR

’S M

AN

UA

L

COMPONENT IDENTIFICATION

OFF

F°

10-02033

200

165

130

95

235270

30

0

CAUTION: READ OPERATOR'S MANUAL

BEFORE OPERATING THIS MACHINE.

IMPROPER OPERATION MAY RESULT IN

PERSONAL INJURY OR PROPERTY DAMAGE.

TEMPERATURE

TEMPERATURA

TEMPERATURE

HOUR METER

HOROMETRO

CHRONOMETRO

0°

RED

15°

YELLOW

40°

WHITE

FOR BEST RESULTS USE

DETERGENTS

DETERGENT VALVE

VALVULA DE DETERGENTE

SOUPAPE DE DETERGENT

BURNER

QUEMADOR

BRULEUR

PUMP

BOMBA

POMPE

0OFF

APAGAR

ETTENT

ION

PRENDER

Burner Exhaust Vent

Thermostat

Pump Switch

High Pressure Nozzle

Wand

High Pressure Hose

Detergent Bucket (not included)

Relief Valve

Burner Switch

Garden Hose (not included)

Trigger Gun

Detergent Control

Nozzles

Pump — Develops high pressure by pumping water volume through nozzle.

Spray Gun — Controls the application of water and detergent onto cleaning surface with trigger device. Includes safety latch.

Detergent Metering Valve — Controls detergent mixture.

Wand — Must be connected to the spray gun.

High Pressure Hose — Connect one end to water pump discharge nipple and the other end to spray gun.

Pressure Nozzle — Inserted into wand quick coupler to develop pressure

Adjustable Thermostat — Prevents water tempera-ture from exceeding high temperatures. Is not used to maintain constant temperature setting.


OP

ER

AT

OR

’S M

AN

UA

L P

RE

SS

UR

E W

AS

HE

R

10

ASSEMBLY INSTRUCTIONS

UnpackingUnpack carefully. Wear safety glasses or goggles while un-packing, assembling or operating pressure washer. If there are missing components or hidden damage immediately contact distributor or carrier concerning discrepancies.

1. Cut strapping band from pressure washer and pallet.

2. Remove pressure washer from pallet.

Parts Included• Pressure Washer

• Pressure Hose

• Hose Hanger

• Wand

• Wand Holder

• Parts Box Containing:

■ Pressure Nozzles (3 ea.)

■ Trigger Gun

• Operating Instructions and Parts Manual

Tools Required• 10" Adjustable Crescent Wrenches (2 ea.)

• Blade Screwdriver

Pressure Hose, Wand and Wand Holder1. Use teflon tape on plumbing connections to prevent

leakage.2. Install pressure hose on machine as shown.3. Assemble wand components as shown. Connect

pressure hose to trigger gun.

NOTE: The nozzle is not to be installed at this time.

4. Make sure that all plumbing connections are tight.

Hose Hanger1. Install the hose hanger on the machine coil tank as

shown.

Quick Disconnect Plug Wand

Quick Disconnect

Trigger Gun

Pressure Hose

Hose Hanger

Pocket On Coil Tank

Relief Valve

Pressure Hose


11

PR

ES

SU

RE

WA

SH

ER

OP

ER

AT

OR

’S M

AN

UA

L

INSTALLATION INSTRUCTIONS

Getting Started

IMPORTANT: Proper initial installation of equipment will assure more satisfactory performance, longer service life and lower maintenance cost.

The pressure washer should be run on a level surface and in a protected area where it is not readily influenced by out-side sources such as strong winds, freezing temperatures, rain, etc. The pressure washer should be located to assure easy access for filling of fluids, adjustments and mainte-nance. Normal precautions should be taken by the operator to prevent moisture from reaching the pressure washer. It is recommended that a partition be made between the wash area and the pressure washer to prevent direct spray from the wand coming in contact with the pressure washer. Moisture reaching the equipment will reduce the pressure washer’s service life. All installations should comply with the local codes covering such installations.

Venting

WARNING - RISK OF EXPLOSION: Do not spray flam-mable liquids or operate machine in areas where flammable vapors are present. Operate only where open flame or torch is permitted.

CAUTION - RISK OF ASPHYXIATION: Do not run machine indoors or in an enclosed area without the required venting, as exhaust fumes may be hazard-ous to your health.

CAUTION: Some gases are heavier than air and will spill out on the floor in the 2 to 3 minutes required for the safety pilot valve to close off gas supply. There-fore, always provide adequate space and ventilation around these units.

IMPORTANT: A draft diverter shall be installed. INSTALLER UNE HOTTE DE TIRAGE.

IMPORTANT: All venting must be in accordance with applicable federal and state laws, and local ordi-nances. Consult local heating contractors.

IMPORTANT: Not suitable for connection to Type B gas vent if the stack temperature exceeds 243°C (470°).

If the pressure washer is to be used in an enclosed area, a flue must be installed to vent burner exhaust to the outside atmosphere. Exhaust gases should not be vented into a wall, a ceiling, or into a concealed space in a building. Be sure the flue is the same size as the burner exhaust vent on the pressure washer. Poor draft will cause the pressure washer to soot and not operate properly. When selecting the location for installation, beware of poorly ventilated locations or areas where exhaust fans may cause an in-sufficient supply of oxygen. Proper combustion can only be obtained when there is a sufficient supply of oxygen available for the amount of fuel being burned. If it is nec-essary to install the machine in a poorly ventilated area, outside fresh air may have to be piped to the burner and a fan installed to bring sufficient air into the machine. Locate

the pressure washer so that the flue will be as straight as possible and protrude through the roof at a proper height and location to provide adequate draft. This gas fired pressure washer must have a draft diverter installed in the flue. A draft diverter will permit proper upward flow of exhaust flue gases.

Hotsy natural and LP gas series pressure washers that incorporate a natural draft burner assembly designed to heat water that comes from the pressure washer pump require a draft diverter and vent pipe for exhausting to the outside. This operator's manual indicates this machine is to be vented through the ceiling using straight pipe or 45° elbows. It also discourages the use of any 90° venting elbows which restrict air flow through the burner causing poor burner conditions. If this machine is going to be in-stalled to a 90° or extended exhaust vent run length which may restrict air flow it is recommended that a contractor install a power vent. When a contractor has found it impos-sible to vent through the ceiling then power venting can be calculated to help eliminate exhaust restriction on this natural draft machine. This draft inducer (power vent) must be installed by a licensed contractor who can calculate size, operation connections and associated dampeners. Hotsy is not a licensed contractor and as such we are unable to make recommendations for suitable make and model of power vents.

It is important that the licensed contractor consult local building codes. Hotsy can only make recommendations and the selection of the venting must take into account the type of roof or wall material it contacts which could change the vent requirement for compliance with local building codes

Water SupplyConnect water supply hose to water inlet. The water faucet and supply hose must be capable of providing a minimum of 6.0 gallons per minute (GPM).

Fuel Supply

CAUTION: Have a qualified gas serviceman install and service your equipment.

WARNING: Gas line supply pressure must not exceed 14 water column inches (.50 PSI).

IMPORTANT: Gas line must be provided with a shut off valve.

IMPORTANT: The gas supply must be able to supply a minimum of 525,000 BTU/HR at the machines rated manifold pressure.

Consult building codes for installation requirements. For proper and safe machine operation, we recommend that a licensed contractor be consulted for machine installation.


OP

ER

AT

OR

’S M

AN

UA

L P

RE

SS

UR

E W

AS

HE

R

12

Natural / Propane GasHave a qualified gas serviceman install the natural gas fuel supply line to the machine.

Gas ValveThe ideal incoming gas pressure is 11 w.c.i. (water column inches) minimum 6 w.c.i., maximum 14 w.c.i. or 1/2 psig. The correct operating manifold pressure for natural gas is 3.5 w.c.i. The operating manifold pressure for propane gas is 11 w.c.i. The gas valve pressure regulator can be adjusted between 3 and 4 w.c.i. natural gas or 6 and 11 w.c.i.for propane.

The gas pressure coming out of the regulator and going to the burner ring has been factory set for elevations of 0 to 2000 ft. Altitudes greater than 2000 ft will require adjust-ments to the gas manifold pressures. Consult your local service dealer/distributor for high altitude adjustments. In Canada, certification for installation at altitudes over 4500 feet above sea level is the jurisdiction of local authorities. You should not readjust the burner ring gas pressure. If you replace your gas valve, you will need to adjust the new valve. Refer to your machine’s specification plate for the correct pressure setting. Follow the installation and adjust-ment instructions provided with your replacement valve.

NOTE: Air for combustion and ventilation along with exhaust flue sizing must conform to methods outlined in current American Standard (ANSI-Z223.1) National Fuel Gas Code or National Standard of Canada CSA-149.1 and CSA-149.2 "Installation Code for Gas Burning Ap-pliances".

Electrical

WARNING: Make sure all switches and controls are in the OFF position prior to connecting electrical supply.

WARNING: DO NOT stand in water while connecting and disconnecting electrical supply.

WARNING: Always disconnect power before servicing your pressure washer.

INSTALLATION INSTRUCTIONS

IMPORTANT: Consult local building codes for exact electrical requirements. Licensed contractors may be required.

IMPORTANT: All wiring must be of proper voltage and amperage rating and conform to applicable codes.

IMPORTANT: This machine must be electrically grounded. LA MACHINE DOIT ÊTRE MISE À LA TERRE.

Grounding Instructions: Make sure all switches and controls are in the OFF position prior to connecting electrical supply. Do not stand in water while connecting and disconnecting electrical supply. If it should malfunc-tion or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. The product must be connected to an appropriate power source that is properly installed and grounded in accordance with all local codes and ordinances.

DANGER: Improper connection of the equipment grounding conductor can result in a risk of electro-cution. Check with a qualified electrician or service personnel if you are in doubt as to whether the outlet is properly grounded.

Extension Cords: Do not use extention cords with this equipment.

WARNING: To reduce the risk of electrocution, keep all connections dry and off the ground.

On/Off Switch

Outlet View

Line to Pilot Light

Manifold Pressure

Adjustment Screw Under

Cap

Inlet View


13

PR

ES

SU

RE

WA

SH

ER

OP

ER

AT

OR

’S M

AN

UA

L

OPERATION INSTRUCTIONS

Before Starting1. Read all manuals provided with this pressure washer.

Become familiar with location and function of all operating and safety controls.

WARNING: Check hoses, fittings, wand, trigger gun and fuel connections daily for signs of wear, cracks and looseness, and replace as required.

2. Connect water supply hose to the standard garden hose connector. The water faucet and supply hose must be capable of providing 6.0 GPM.

3. This machine was factory built for Natural Gas. See instructions under Fuel Supply.

4. Check pump oil level.5. If detergents are to be used, only use detergents

intended for pressure washers. Follow instructions on the detergent container.

IMPORTANT: Before installing pressure nozzle on initial start-up, turn on the water supply, start the pump by pressing the pump ON switch, and hold the wand trigger open until water appears at the end of the wand. Allow water to run from the end of the wand until clear to prevent the nozzle from clogging.

IMPORTANT: If the pressure washer has not been used for an extended period of time, remove the pressure nozzle from the end of the wand and turn on water supply, and start the pump by pressing the pump ON switch. Hold the wand trigger open and allow water to run from the end of the wand until clear.

6. Install the pressure nozzle on end of wand, refer to illustration below.

IMPORTANT: The trigger gun provided with this pres-sure washer is equipped with a manual trigger lock to prevent accidental operation of the trigger gun, refer to figure above. The trigger lock should be used whenever the trigger gun is not in use.

IMPORTANT: On initial start-up or if maintenance has been performed on the burner assembly, it will be necessary to bleed the air from the gas line before the pilot will light.

7. If you are running the machine for the first time, or have performed maintenance on the burner assembly, there will be air in the gas line. To bleed the air from the gas line run the pressure washer with pump and burner switches on and thermostat on highest setting. Squeeze the trigger of the trigger gun for 15 seconds.

If the burner has not ignited, release the trigger for 5 seconds, then squeeze for 15 seconds. If the burner has not ignited after 10 tries, see the Troubleshoot-ing Guide in this manual.

CAUTION: Have a qualified gas serviceman install and service your equipment.

DANGER: Never expose a spark or flame where there may be unburned gas present.

DANGER: Some gases are heavier than air and will spill out on the floor in the 2 to 3 minutes required for the safety pilot valve to close off gas supply. There-fore, always provide adequate space and ventilation around these units.

To Start

WARNING: Risk of injection or severe injury - Keep clear of nozzle - DO NOT direct discharge stream at persons - This machine is to be used only by quali-fied operators.

AVERTISSEMENT: RISQUE D’INJECTION ET DE BLESSURES GRAVES. SE TENIR À L’ÉCART DU JET. NE PAS DIRIGER LE JET DE SORTIE VERS D’AUTRES PERSONNES. CONFIER L’UTILISATION DE CE MATÉ-RIEL À UN OPÉRATEUR QUALIFIÉ.

WARNING: Wear eye, ear, hand, foot and skin protec-tion at all times while operating pressure washer.

WARNING: Before changing pressure nozzle, engage manual trigger gun lock.

IMPORTANT: The water must be turned on before starting. Running the pump dry will cause damage and void warranty.

IMPORTANT: Do not allow the machine to run with trigger of the trigger gun released for more than 10 minutes at any one time or damage to pump may occur.

1. Turn ON water supply.2. Turn ON gas supply.3. Hold wand firmly, release trigger of trigger gun and

turn pump switch ON. Squeeze trigger of trigger gun and allow air to purge from system.

4. If HOT water is desired, adjust the thermostat to the proper temperature and turn burner switch ON. Squeeze trigger of trigger gun. The pilot will automati-cally light, quickly followed by the firing of the burner ring. When the trigger of the trigger gun is released or when the thermostat temperature setting is reached, the burner will automatically turn off.

IMPORTANT: If ignition or flame failure is experienced, discontinue use of pressure washer at once. Turn off burner and shut off fuel supply. Have cause of failure corrected by an authorized service technician before use of pressure washer is continued.

Manual Trigger Lock

Pressure Nozzle


OP

ER

AT

OR

’S M

AN

UA

L P

RE

SS

UR

E W

AS

HE

R

14

OPERATION INSTRUCTIONS

To Clean

WARNING: Risk of injection or severe injury - Keep clear of nozzle - DO NOT direct discharge stream at persons - This machine is to be used only by quali-fied operators.

AVERTISSEMENT: RISQUE D’INJECTION ET DE BLESSURES GRAVES. SE TENIR À L’ÉCART DU JET. NE PAS DIRIGER LE JET DE SORTIE VERS D’AUTRES PERSONNES. CONFIER L’UTILISATION DE CE MATÉ-RIEL À UN OPÉRATEUR QUALIFIÉ.

1. Insert detergent inlet line into container of mixed detergent. Open detergent ON/OFF valve. The detergent will be pulled automatically into the sys-tem. Allow detergent to reach end of wand before proceeding to step 3.

2. Select pressure nozzle with spray pattern that match-es your cleaning needs. Engage manual trigger lock and install selected nozzle.

3. Wash from the bottom to the top, using side to side motions. This washes away heavy dirt and allows the detergent to soak as you work toward the top.

4. Do not wash at a 90° angle to the work (straight at it). This will allow water to splash back at you and reduces your cleaning power. Wash at a 30° to 60° angle to the work. This will allow the water to splash away from you and the water will wash the dirt away faster and easier.

5. Use the width of the spray pattern to wash in a wide path. Overlap spray paths for complete coverage. Wash from side to side, using slow, steady motions.

6. The nozzle should be 12" to 24" from work, closer for tough areas. Be careful on painted or delicate surfaces, the pressure may damage surface if nozzle is too close.

7. Small parts should be washed in a basket and larger, lightweight parts should be clamped down so the pressure does not push them away.

8. Close the detergent ON/OFF valve to permit rinse. Always rinse with cold water after using detergents. Rinse from the top to the bottom to prevent detergent from dripping onto a rinsed area. For the best results, contact your Hotsy dealer to help you select the best detergent for your application.


15

PR

ES

SU

RE

WA

SH

ER

OP

ER

AT

OR

’S M

AN

UA

L

SHUTDOWN INSTRUCTIONS

To Stop1. If detergents were used, draw clear water through

the detergent line to purge detergent. Failure to do so may clog detergent injector valve.

2. If burner was used, turn OFF burner switch and allow pump to run cold water through coil for several minutes.

3. Turn pump switch OFF.4. Turn water supply OFF.5. Squeeze trigger gun open to relieve system pres-

sure.6. Depress gas control knob slightly and turn to OFF

position.7. Turn off main shut-off valve on gas supply.

STORAGE INSTRUCTIONS

DANGER: Do not store flammable liquids (gasoline, diesel fuel, petroleum, solvents, etc.) near pressure washer, or in non-ventilated areas.

IMPORTANT: Machine must be stored indoors.

1. Protect from freezing by storing in a heated area, or by flushing the system with antifreeze (use an automotive engine antifreeze or windshield washer solvent to antifreeze). To flush the system fill the float tank with antifreeze and remove pressure nozzle from wand. Start the machine and allow it to run until antifreeze runs from the end of the wand. Place wand into float tank and circulate the solution

through system for several minutes. Open and close the trigger gun several times to circulate antifreeze through the unloader valve system. Also draw anti-freeze through the detergent inlet line to antifreeze the detergent system. For added protection after anti-freezing, disconnect the pressure hose from machine and remove the coil drain plug (refer to Component Identification illustration for location). After coil has drained, replace pressure hose and coil drain plug. If the pressure washer is not to be used for an extended length of time, it is recommended that the system be flushed with antifreeze for rust protection.


OP

ER

AT

OR

’S M

AN

UA

L P

RE

SS

UR

E W

AS

HE

R

16

WARNING: Unauthorized machine modification or use of non-approved replacement parts may cause personal injury and/or property damage and will void the manufacturer warranty.

PumpUse Hotsy Pump Oil P/N 315068 for pump crankcase. Crankcase must be filled to the full mark on the dipstick or to center of sight glass window found on the rear of the pump. During the break-in-period, make sure the oil is changed after the first 25 hours of operation. After that, replace oil every 3 months or 300 hours of operation, whichever comes first.

Proper Pump Care:• Do not pump acids.

• Do not allow pump to run dry.

• Winterize if storing in freezing temperatures; refer to Storage for details.

• Use a water softener on the water system if known to be high in mineral content.

• Use only high quality detergents and follow manu-facturer’s mix recommendations.

• Flush the system with clear water immediately after using detergent solutions.

• Clean filter screen on detergent inlet line periodi-cally.

• Flush the pressure washer system with antifreeze if storing for an extended period of time; refer to Storage for details.

MAINTENANCE

Pump MotorOn a yearly basis, oil pump motor per instructions on motor nameplate.

NOTE: Some motors may be equipped with perma-nently lubricated bearings and will not require ad-ditional lubrication.

Gas BurnerIt is recommended that the gas burner be serviced yearly or as needed. Contact your local service center.

Relief Valve

WARNING: The relief valve on this pressure washer has been factory set and sealed and is a field nonad-justable part. Tampering with the factory setting may cause personal injury and/or property damage, and will void the manufacturer warranty.

Unloader Valve

WARNING: The unloader valve on this pressure washer has been factory set and sealed and is a field nonadjustable part. Tampering with the factory setting may cause personal injury and/or property damage, and will void the manufacturer warranty.

Heating CoilCoil Descaling: In hard water areas, scale buildup within the heating coil will occur. Scale deposits will decrease the water temperature rise and may eventually clog the heating coil. Contact your local service center when des-caling is needed.

Coil Desooting: Poor grades of fuel oil or inadequate combustion air will cause heavy soot buildup on the outside surface of the heating coil. These deposits will insulate the coil. This will restrict the air flow through the coil, further aggravating the soot buildup. Contact your local service center when desooting is needed.

Dipstick

Sight Glass (on Rear of Pump)

Oil Fill


17

PR

ES

SU

RE

WA

SH

ER

Tro

ub

lesho

otin

g G

uid

eTROUBLESHOOTING

SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION

PRESSURE WASHERWILL NOT RUN

Pump switch in OFF position Place switch in ON position.

Power supply disconnected Connect power supply.

Fuse blown or circuit breaker tripped in electrical supply line

Replace fuse or reset circuit breaker. Use only circuits of adequate capacity.

Motor circuit overload tripped Allow sufficient time for motor to cool down. Place pump switch in ON position.

PRESSURE WASHERRUNS BUT WON'TSPRAY

Trigger of trigger gun released Squeeze trigger.

Water supply not turned on Open water supply valve.

Clogged pressure nozzle Clean pressure nozzle opening.

Inlet water screen clogged Check screen and clean if necessary.

Pump sucking air Fill the detergent container and check for loose hose clamps or fittings.

LOW SPRAY PRESSURE ATNOZZLE

Inadequate water supply Fully open faucet. Check for kinked or damaged hose. Use 5/8" minimum hose. Check for debris clogging inlet screen.

Partially clogged or damaged pressure nozzle

Clean or replace.

Air being drawn through detergent inlet line

Refill detergent container. Ensure that pick-up screen is fully immersed.

UNEVEN SPRAY PATTERN

Partially clogged or damaged pressure nozzle

Clean or replace.

PRESSURE WASHERWILL NOT PRODUCEHOT WATER

Burner switch in OFF position Place switch in ON position.

Gas valve switch in OFF position Place switch in ON position.

Inadequate fuel supply Check fuel supply.

Pump switch turned off Pump must be running before burner will light.


PR

ES

SU

RE

WA

SH

ER

T

rou

ble

sho

oti

ng

Gu

ide

18

TROUBLESHOOTING

SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION

PRESSURE WASHER WILL NOT PRODUCE HOT WATER(Continued)

Inadequate water supply Fully open faucet. Check for kinked or damaged hose. Use 5/8" minimum hose. Check for debris clogging inlet screen.

Trigger of trigger gun released Squeeze trigger. Water must be spraying for burner to light.

Thermostat set too low, or defective

Raise thermostat setting. Replace if defective.

Manual gas valve not open Turn ON gas valve.

Defective gas valve Replace gas valve.

POOR OR NO DETERGENTFLOW

Inadequate detergent supply Refill detergent container. Ensure that pick-up screen is fully immersed.

Detergent screen or hose clogged Clean. Always start with a clean detergent container.

Clogged detergent injector check valve

Clean check valve at detergent injector.

POOR CLEANING Improper detergent concentration or mixing

Mix detergent per manufacturer's instruc-tions. Ensure that powdered detergents are fully dissolved.

Wrong detergent for the application Select appropriate detergent.

Rinsing with hot water A final rinse with cold water will reduce water spotting.

Detergent valve not opening Check that handle or knob is not slipping on shaft.

UNLOADER CYCLES WHEN TRIGGER GUN IS OPENED OR CLOSED

Air in system Open and close trigger gun several times.

Unloader defective Replace if defective.

Water leak between unloader valve and trigger gun

Check fittings, hose and trigger gun for leaks. Repair or replace.

BURNER SMOKES OR HAS OBNOXIOUS ODOR

Stack restriction See Venting under Installation.

PRESSURE RELIEF VALVELEAKING

Excessive pressure due to defective unloader valve

Replace unloader valve.

Defective relief valve Replace relief valve.

Dirty relief valve Clean relief valve seat


19

PR

ES

SU

RE

WA

SH

ER

Tro

ub

lesho

otin

g G

uid

eTROUBLESHOOTING

GAS-FIRED SERIES OPTIONAL EQUIPMENT 835526 Draft Diverter, 8"

When ordering from your dealer, please provide the following:

Model Number: _____________________Release:___________

Machine Serial Number: ________________________________

Component Part Number: _______________________________

Description: __________________________________________

IMPORTANTIf the pressure washer demonstrates other symptoms or the corrective actions listed do not correct the problem, contact the local authorized Hotsy Service Center. The Hotsy Service Center can be identified by visiting www.hotsy.com.


OP

ER

AT

OR

’S M

AN

UA

L P

RE

SS

UR

E W

AS

HE

R

20

89144050-2

2

3

4

4

56

8

1

2126

25

24

27

754

12

1311

25

26

9 28

23

30

37

56

32

31

22

29

ForDetail See Float Tank

Illus.

37

39

62

27

27

34

33

ForDetail See

Burner Assy.

35

29

38

EXPLODED VIEW

59

60

20

66

61

60

65

57

26

Optional Hose Reel

See Float Tank Illus. For Detail

26

58

51

11

14

25 2671

15

17

18 70


21

PR

ES

SU

RE

WA

SH

ER

OP

ER

AT

OR

’S M

AN

UA

L

89144050-5

40

5726

26

58

41

49

52

7230

Thermal Switch Option

SeePump

Assy. for Detail

45

44

47

48

46

3637

42

55

To Float Tank

See Control

Panel Illus. for Detail

EXPLODED VIEW

43

72

30

2526

63

64

67 68

73

26

25

50

73

16

53

81

19

10

26

25

26

25


OP

ER

AT

OR

’S M

AN

UA

L P

RE

SS

UR

E W

AS

HE

R

22

EXPLODED VIEW PARTS LIST

ITEM PART NO. DESCRIPTION QTY 1 8.911-327.0 Top Hat, Weld Assy., 18" Hotsy Coil 1

2 8.717-442.0 Insulation, Top Head, 18 OD x 1.8 ID, Fiberglass 1

3 9.803-108.0 Ring, Insulation Retainer, 16" Top Hat 1

4 8.718-940.0 Screw, #10 x 34 HWH Tek SS 2

5 8.911-498.0 Coil, Service Gas 900/1000 1

6 8.717-518.0 Insulation, 30.75 x 59, Fiberglass 1

7 8.911-808.0 Coil, SS, Tank, Weldment 1

8 8.719-946.0 Hanger, Hose 1

9 8.901-215.0 Label, Lexan, Hotsy, 8.6" x 3.25" 2

10 8.915-063.0 Panel, Right Side 1

11 8.718-760.0 Screw, 10/32" x 5/8" Phil Pan SS 1

12 9.802-038.0 Nipple, 1/2" JIC, 1/2" Pipe 1

13 8.706-172.0 Elbow, 1/2", 90° Female Pipe 1

14 9.802-695.0 Nut, 10/32" KEPS 1

15 8.911-953.0 Bracket, Transformer

(969SS, 1469SS) 1

16 9.800-049.0 Label, Detergent Warning 1

17 9.802-710.0 Bolt, 5/16" x 1" NC, HH (969SS, 1469SS) 2

18 9.802-804.0 Washer, 5/16" Flat, SAE (969SS, 1469SS) 2

19 9.802-813.0 Washer, 5/16" Lock, Split Ring 4

20 8.711-785.0 Hose, 3/8" Push-On 45"

21 9.804-072.0 Conduit, Flexo, Black 42"

22 8.911-944.0 Frame, Welded Assembly, Gas 1

23 8.911-939.0 Panel, 900/1400 Side 1

24 9.803-545.0 Grommet, 2-1/8" x 2-7/8" x 7/16"Rubber 1

25 8.718-582.0 Bolt, 1/4" x 1/2", NC HH 17

26 9.802-803.0 Washer, 1/4" Flat, SAE 23

27 9.802-403.0 Bushing, 5/8" Snap 6

28 8.911-829.0 Slider, Pump, Weldment 1

29 9.802-776.0 Nut, 5/16" ESNA, NC 8

30 8.718-980.0 Washer, 5/16" Flat, SAE 8

31 9.803-845.0 Bolt, 1/2" x 5" NC HH Tap, All Thread 1

32 9.802-800.0 Washer, 1/2" Flat, SAE 1

33 8.706-728.0 Bushing, 1-3/8" Snap 1

34 8.911-938.0 Panel, Long Frame Cover 1

ITEM PART NO. DESCRIPTION QTY 35 8.911-937.0 Panel, Small Frame Cover 1

36 9.802-779.0 Nut, 3/8" ESNA, NC 4

37 9.802-807.0 Washer, 3/8" SAE, Flat 12

38 8.719-000.0 Washer, 5/16" x 1-1/4" Fender, SAE 4

39 9.802-720.0 Bolt, 3/8" x 1" NC HH 4

40 8.911-940.0 Panel, Back Welded Assy. 1

41 8.911-949.0 Bracket, Unloader 1

42 8.911-935.0 Panel, Front 1

43 Motor, Please See Specifications Page 1

44 8.715-701.0 Belt, BX40 2

45 Pump Pulley, Please See Specifications Page

46 Motor Pulley, Please See Specifications Page

47 9.802-402.0 Bushing, H x 24 mm 1

48 Motor Bushing, Please See Specifications Page

49 8.911-942.0 Cover, Back Panel 1

50 8.915-062.0 Cover, Cabinet 1

51 9.802-203.0 Clamp, 1/2" 1

52 9.802-042.0 Elbow, 1/2" JIC x 3/8" Female, 90° 1

53 8.718-936.0 Screw, #8 x 1/2", Phillips, Zinc 2

54 8.900-990.0 Label, Warning 1

55 8.900-923.0 Label, Hotsy 900/1400 Control Panel 1

56 9.802-744.0 Bolt, 10 mm x 20 mm, HH 4

57 9.802-700.0 Bolt, 1/4" x 3/4" NC HH 4

58 9.802-773.0 Nut, 1/4" ESNA, NC 4

59 8.918-236.0 Hose, 3/8" 2 Wire Pressure Loop 27"

60 9.802-704.0 Screw, 1/4-20 x 1/2" Tri-Round, Black, Zinc 12

61 8.900-858.0 Label, Natural Gas (NG Models) 1

8.940-281.0 Label, LP (LP Models) 1

62 9.803-544.0 Grommet, Rubber 1

63 9.802-518.0 Strain Relief, 3/4" (1410SS, 1411SS, 1412SS, 1420SS-208, 1421SS-208, 1422SS-208, 1450SS-208, 1452SS-208, 1467SS, 1469SS) 1

9.803-280.0 Locknut, 1", Conduit 1 9.803-279.0 Strain Relief, CG100-750, 1" (1420SS,1421SS, 1422SS, 1423SS, 1424SS, 1425SS) 1


23

PR

ES

SU

RE

WA

SH

ER

OP

ER

AT

OR

’S M

AN

UA

L

EXPLODED VIEW PARTS LIST

ITEM PART NO. DESCRIPTION QTY 64 9.802-429.0 Cord, Service, 12/4 (992S, 969SS, 991SS, 991SS-208, 992SS-208,994SS, 995SS, 1424SS, 1425SS,1469SS) 45"

9.802-436.0 Cord, Service, 10/3 (952SS-208, 982SS, 981SS) 45"

9.802-437.0 Cord, Service, 10/4 (1422SS-208, 1422SS, 1421SS-208, 1421SS) 45"

9.802-425.0 Cord, Service, 8/3 (1411SS, 1412SS, 1452SS-208) 45"

65 9.802-064.0 Grommet, Rubber 1

66 9.800-021.0 Label, Hot Water 1

67 8.911-948.0 Cover, Electrical Box 1

68 9.800-016.0 Label, Disconnect Power Supply 1

69 8.718-780.0 Screw, 4 mm x 4 mm, Panhead 1

70 9.802-776.0 Nut, 5/16" ESNA, NC (969SS, 1469SS) 2

71 9.800-020.0 Label, Cold Water Inlet 1

72 9.802-709.0 Bolt, 5/16" x 3/4" NC, Grade 5 4

73 8.932-965.0 Label, Exposed Label 2


OP

ER

AT

OR

’S M

AN

UA

L P

RE

SS

UR

E W

AS

HE

R

24

Honeywell

PV

MV MPV

V

ON

OFF

PSIIN

BURNER ASSEMBLY29

4520

13

1415

13

126

11

8

9

10

5

7 (union)

2

18

1918 16

19

1

19

26

21

2322

25

28

27

3

5


25

PR

ES

SU

RE

WA

SH

ER

OP

ER

AT

OR

’S M

AN

UA

L

BURNER PARTS LIST

ITEM PART NO. DESCRIPTION QTY 1 8.911-313.0 Angle, Gas Burner Bracket 1

2 Burner Ring, Please See Specifications Page 1

3 9.802-021.0 Nipple, 3/4" x 9" Black 1

4 9.802-027.0 Elbow, 3/4" Black, 90° 1

5 9.802-017.0 Nipple, 3/4" x Close, Black 3

6 9.802-019.0 Nipple, 3/4" x 2" Black 1

7 9.802-049.0 Union, 3/4" Black Pipe 1

8 8.706-222.0 Tee, 3/4" Black Pipe 1

9 9.803-561.0 Nipple, 3/4" x 5" Black Pipe 1

10 8.706-320.0 Cap, 3/4" Black Pipe 1

11 9.802-911.0 Tubing, Aluminum, 600" /RL, 1/4" 10"

12 8.707-029.0 Elbow, 1/4" Tube x 1/8" MPT, 90° 1

13 8.706-910.0 Bushing, 1/4" x 1/8" Pipe 2

14 9.803-563.0 Connector, 1/4" Tube x 1/8" MPT 1

15 9.802-178.0 Valve, Ball, 1/4" Female x 1/4" Female 1

16 9.802-714.0 Bolt, 5/16" x 1-3/4", NC HH 1

17 8.911-951.0 Bracket, Gas Train 1

18 8.718-980.0 Washer, 5/16" Flat, SAE 6

19 9.802-778.0 Nut, 5/16" Flange, Whiz Loc 3

20 9.803-616.0 Valve, 3/4", Natural Gas, 24V, 3.5 Honeywell 1

21 9.803-610.0 Pilot, Ignitor, P, NG 1

22 8.719-957.0 Bracket, Pilot Light 1

23 8.718-582.0 Bolt, 1/4" x 1/2" NC HH 2

24 9.802-802.0 ▲ Washer, 1/4" Flat 2

25 9.802-772.0 Screw, 10/32" x 1/4" HWH ROLOC, Z 2

26 9.802-718.0 U-Bolt, 5/16" x 1", Pipe 1

27 8.905-681.0 Cable, Ignition, 60" 1

28 9.803-618.0 LP, Conversion Kit (981SS, 991SS, 991SS-208, 994SS, 1411SS, 1421SS, 1421SS-208, 1424SS) 1

▲ Not Shown


OP

ER

AT

OR

’S M

AN

UA

L P

RE

SS

UR

E W

AS

HE

R

26

89144050-4

PUMP ASSEMBLY EXPLODED VIEW

11

2

4

21

15

23

12

25

22

1

3

18

17

16

9 27

10

242019

9

7

14

8

26

5

28

6

13

3032

299

9

31


27

PR

ES

SU

RE

WA

SH

ER

OP

ER

AT

OR

’S M

AN

UA

L

PUMP ASSEMBLY EXPLODED VIEW PARTS LIST

ITEM PART NO. DESCRIPTION QTY 1 9.802-039.0 Elbow, 1/2" JIC, 3/8", 90° 1

2 8.715-489.0 Unloader, YVB9KMSS, W/S.S., Check Valve 1

3 9.802-129.0 Elbow, 1/2" JIC x 3/8", 90° 1

4 8.706-234.0 Tee, 3/8" Street 1

5 8.707-232.0 Valve, 1/2" FNWTSC12, Brass, Swing Check 1

6 9.802-131.0 Elbow, 1/2" JIC x 1/2", 90° 1

7 9.802-128.0 Nipple, 1/2" JIC x 1/2" MPT Pipe 1

8 8.706-860.0 Tee, 1/2" Street 1

9 9.802-151.0 Swivel, 1/2" JIC Female, Push-On 4

10 9.802-259.0 Hose, 1/2" Push-On 20"

11 9.802-043.0 Elbow, 1/2" JIC x 3/8" Fem, 90° 1

12 8.706-965.0 Hose, Barb, 1/4" Barb x 3/8" ML Pipe, 90° 1

13 8.716-125.0 Switch, Pressure, Black 1

14 8.706-797.0 Nipple, 1/2" Hex 1

15 6.390-126.0 Clamp, Hose, UNI .46 - .54 ST 1

16 9.802-038.0 Nipple, 1/2" JIC, 1/2" Pipe 1

17 8.706-172.0 Elbow, 1/2", 90° Female Pipe 1

18 8.705-975.0 Nipple, 1/2" Hex Steel 1

19 9.802-744.0 Bolt, 10 mm x 20 mm, HH 4

20 9.802-807.0 Washer, 3/8" Flat, SAE 4

21 9.802-252.0 Hose, 1/4" x 1/2" Braided Vinyl 36"

22 9.802-048.0 Swivel, 1/2" JIC Female, 3/8" Male 1

23 9.802-041.0 Elbow, 3/8" STL, Street, 45° 1

24 8.911-829.0 Slider, Pump, Weldment 1

25 8.706-248.0 Plug, 3/8" Allen Counter Sunk 1

26 9.802-259.0 Hose, 1/2" Push-On, Fuel Line 30"

27 9.802-126.0 Plug, 1/2" JIC 1


29 9.802-129.0 Elbow, 1/2" JIC x 3/8", 90° 1

30 Pump, Please see Specifications Page

31 9.802-259.0 Hose, 1/2" Push-On, Fuel-Line 22.5"

32 8.706-917.0 Bushing, 1/2"x 3/8" Brass 1


OP

ER

AT

OR

’S M

AN

UA

L P

RE

SS

UR

E W

AS

HE

R

28

FLOAT TANK ASSEMBLY

82

13

14

16

15

19

14

1

5

4 3

2

20

18

12

7

10

6

11

13

9

17

6

To Pump Assy


29

PR

ES

SU

RE

WA

SH

ER

OP

ER

AT

OR

’S M

AN

UA

L

FLOAT TANK PARTS LIST

ITEM PART NO. DESCRIPTION QTY 1 9.804-042.0 Tank, Float, 2-1/2" Gallon, Blank 1

2 8.707-000.0 Connector, 1/2" Anchor 1

3 8.749-328.0 Valve, 1/2" Plastic Float 1

4 8.706-512.0 Ball, Float, Black Plastic 1

5 9.803-671.0 Stem, 5", Float 1

6 8.718-980.0 Washer, 5/16" Flat, SAE 4

7 8.911-952.0 Bracket, Hose Reel 1

8 9.802-146.0 Swivel, 1/2" MP x 3/4" GHF w/Strainer 1

9 8.709-091.0 Clip, 1.25 ID, RND 1

10 8.718-618.0 Bolt, 5/16" x 3/4" NC, Grade 5 2

11 9.802-794.0 Nut, Cage, 1/4" x 12 Gauge 2

12 9.802-775.0 Nut, 1/4" Flange, Zinc 1

13 9.802-700.0 Bolt, 1/4" x 3/4" NC HH 3

14 9.802-802.0 Washer, 1/4" Flat, SAE 3

15 9.802-776.0 Nut, 5/16" Esna 2

16 8.911-947.0 Bracket, Float Tank 1

17 8.706-947.0 Hose Barb, 1/2" Barb x 1/2" MNPT 1


19 8.707-061.0 Strainer, 1/2" Basket 1

20 9.802-259.0 Hose, 1/2" Push-On 27.5"


OP

ER

AT

OR

’S M

AN

UA

L P

RE

SS

UR

E W

AS

HE

R

30

For Nozzle Information, See Hose and Trigger

Gun Assembly Page

CONTROL PANEL ASSEMBLY

3916

15

7,8,9

43

5

29

10

18

17

13

12

11

12

42

25

19

14

24

ToPump

38

1

26

33

22

20

23

4

29 30

Reversed View

32

31

10

35

34

41

14

36

20

21

37

2123

6

40

2844

45

46

47

40

49

48

50


31

PR

ES

SU

RE

WA

SH

ER

OP

ER

AT

OR

’S M

AN

UA

L

CONTROL PANEL PARTS LIST

ITEM PART NO. DESCRIPTION QTY 1 9.803-613.0 Module, Ignition, Electronic Honeywell 1

2 9.802-283.0 Meter, Hour 1

3 8.750-097.0 Knob, Thermostat 1

4 8.716-037.0 Switch, Rocker, 10A/250V/125V, 24 Volt 1

5 8.716-086.0 Relay, 24 Volt, DPST NO 2

6 8.716-394.0 Block, Terminal, 14 Pole 1

7 8.716-460.0 Lug, Terminal Grounding, LAMA6-14-Q 1

8 9.803-660.0 Screw, 8-32 x 1-1/4", M PH PHD PL 1

9 9.802-785.0 Nut, 8/32" Keps 4

10 8.718-936.0 Screw, #8 x 1/2" Tek, Square Head, SS 6

11 9.802-188.0 Valve, Metering, 1/4" Hose 1

12 6.390-126.0 Clamp, Hose, .46 -, .54 ST 2

13 9.802-252.0 Hose, 1/4" x 1/2" Braided Vinyl 11 ft.

14 9.802-064.0 Grommet, Rubber, Nozzle Holder 3

15 8.911-936.0 Stand-Off, E-Box 1

16 Contactor, Please See Specifications Page

17 Overload, Please See Specifications Page

18 Transformer, Please See Specifications Page

19 8.900-923.0 Label, Hotsy, 900/1400 Control Panel 1

20 9.802-514.0 Strain Relief, Straight, LQ Tite Small 3

21 9.802-525.0 Locknut, 1/2" Conduit 3

22 9.802-518.0 Strain Relief, Straight, LQ Tite Large 2

23 9.802-526.0 Locknut, 3/4" 2

24 8.707-058.0 Strainer, 1/4" Brass w/Check Valve 1

25 8.718-762.0 Screw, 8-32 x 1/2", M PH RDH PL 4

ITEM PART NO. DESCRIPTION QTY 26 9.802-778.0 Nut, 5/16" Flange, Whiz Loc 4

27 9.802-776.0 Nut, 5/16" ESNA, NC 4


29 8.716-199.0 Fuse, FNM-6.25 1

30 Fuse, Please See Specifications Page

31 8.911-948.0 Cover, Electrical Box 1

32 9.800-016.0 Label, Disconnect Power Supply 1

33 8.750-095.0 Thermostat 120C/240F 2 Meter Capillary 1

34 8.712-190.0 Plate, Thermostat 2

35 8.718-779.0 Screw, 4mm x 6mm, Panhead 2

36 8.706-755.0 Bushing, Star 1

37 9.802-105.0 Plug, 7/8" Hole 1

38 9.802-785.0 Nut, 8/32" Keps 4


40 8.718-937.0 Screw, #8 x 3/4" Tek, Zinc 2

41 9.802-103.0 Bushing, 5/8" Snap 1

42 9.802-252.0 Hose, 1/4" x 1/2" Braided Vinyl 3 ft.

43 9.802-457.0 Rail, Din, 35mm (All Models Except 952SS, 952SS-208, 1411SS, 1412SS, 1452SS, 1452SS-208, 1426SS-208) 2"

44 8.713-698.0 Connector, Electrical 9 Pin Female 1

45 8.713-699.0 Connector, Electrical 9 Pin Male 1

46 8.713-697.0 Connector, Electrical 6 Pin Male 1

47 8.713-731.0 Connector, Electrical 6 Pin Female 1

48 8.713-768.0 Connector, Electrical Pin Male 13

49 8.713-604.0 Connector, Electrical Pin Female 4

50 9.802-457.0 Din Rail, 35mm 2.5"


OP

ER

AT

OR

’S M

AN

UA

L P

RE

SS

UR

E W

AS

HE

R

32

COIL OUTLET ASSEMBLY

COIL OUTLET ASSEMBLY PARTS LIST

89144120-4

1

2

4

3

5

ITEM PART NO. DESCRIPTION QTY 1 9.149-003.0 Manifold Coil Outlet Discharge 1

2 9.196-012.0 Screw, 10-24 x 1/4" Hex Set 1

3 8.902-433.0 Valve, Safety Relief, VSA 1

4 9.802-171.0 Nipple, 3/8" x 3/8" NPT ST Male 1

5 8.706-248.0 Plug, 3/8" Allen Counter Sunk 1

6 8.711-785.0 Hose, 3/8" Push-on 43"

6


33

PR

ES

SU

RE

WA

SH

ER

OP

ER

AT

OR

’S M

AN

UA

L

HOSE, GUN & WAND ASSEMBLY

HOSE, GUN & WAND ASSEMBLY PARTS LIST

5

42

1

3

3

6,7,8

ITEM PART NO. DESCRIPTION QTY 1 8.749-171.0 Gun, Shut-off, Hotsy 5000 PSI, 10.5 GPM 1

2 8.707-139.0 Nipple, 1/4" x 1/4" NPT ST Male 1

3 9.802-164.0 Coupler, 1/4" Female, Brass 2

4 8.725-389.0 Wand, Single, 36" Insulated, w/Side Grip 1

5 8.739-011.0 Hose, 3/8" x 50', 1 Wire, Tuff-Skin 1

6 8.712-349.0 Nozzle, 4.5 Red (1400 Series) 1

8.712-357.0 Nozzle, 5.5 Red (981SS, 982SS, 991SS, 991SS-208, 992SS, 992SS-208, 994SS, 995SS) 1

8.712-353.0 Nozzle, 5.0 Red (952SS, 952SS-208, 962SS, 962SS-208, 964SS, 969SS) 1

7 8.712-350.0 Nozzle, 4.5 Yellow (1400 Series) 1

8.712-358.0 Nozzle, 5.5 Yellow (981SS, 982SS, 991SS, 991SS-208, 992SS, 992SS-208, 994SS, 995SS) 1

8.712-354.0 Nozzle, 5.0 Yellow 952SS, 952SS-208, 962SS, 962SS-208, 964SS, 969SS) 1

ITEM PART NO. DESCRIPTION QTY8 8.712-352.0 Nozzle, 4.5 White (1400 Series) 1

8.712-360.0 Nozzle, 5.5 White (981SS, 982SS, 991SS, 991SS-208, 992SS, 992SS-208, 994SS, 995SS) 1

8.712-356.0 Nozzle, 5.0 White 952SS, 952SS-208, 962SS, 962SS-208, 964SS, 969SS) 1

REPLACEMENT PARTS 8.749-354.0 Kit, Gun Repair, Branded 1


OP

ER

AT

OR

’S M

AN

UA

L P

RE

SS

UR

E W

AS

HE

R

34

SPECIFICATIONS

Model Nozzle MotorMotor

HP Contractor OverloadTrans-Former Pump

PumpPulley Model

MotorPulley

MotorBushing Burner Pilot

GasValve

LPConv.

Fuse (2)

981SS 5.5 8.715-142.0 5 8.724-280.0 8.724-305.0 9.803-662.0 8.750-746.0 8.715-592.0 981SS 8.715-582.0 9.802-400.0 8.718-056.0 9.803-610.0 9.803-616.0 9.803-618.0 8.713-286.0

982SS 5.5 8.715-142.0 5 8.724-280.0 8.724-305.0 9.803-662.0 8.750-746.0 8.715-592.0 982SS 8.715-582.0 9.802-400.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-286.0

991SS 5.5 8.751-013.0 5 8.724-269.0 8.724-304.0 9.803-662.0 8.750-746.0 8.715-592.0 991SS 8.715-582.0 9.802-400.0 8.718-056.0 9.803-610.0 9.803-616.0 9.803-618.0 8.713-286.0

991SS-208 5.5 8.715-092.0 5 8.724-269.0 8.724-304.0 9.803-662.0 8.750-746.0 8.715-592.0 991SS-208 8.715-582.0 9.802-400.0 8.718-056.0 9.803-610.0 9.803-616.0 9.803-618.0 8.713-286.0

992SS 5.5 8.751-013.0 5 8.724-269.0 8.724-304.0 9.803-662.0 8.750-746.0 8.715-592.0 992SS 8.715-582.0 9.802-400.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-286.0

992SS-208 5.5 8.715-092.0 5 8.724-269.0 8.724-304.0 9.803-662.0 8.750-746.0 8.715-592.0 992SS-208 8.715-582.0 9.802-400.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-286.0

994SS 5.5 8.751-013.0 5 8.724-269.0 8.724-303.0 8.716-886.0 8.750-746.0 8.715-592.0 994SS 8.715-582.0 9.802-400.0 8.718-056.0 9.803-610.0 9.803-616.0 9.803-618.0 8.713-080.0

995SS 5.5 8.751-013.0 5 8.724-269.0 8.724-303.0 8.716-886.0 8.750-746.0 8.715-592.0 995SS 8.715-582.0 9.802-400.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-080.0

1411SS 4.5 8.715-102.0 7.5 8.724-283.0 8.724-306.0 9.803-662.0 8.750-746.0 8.715-592.0 1411SS 8.715-582.0 9.802-401.0 8.718-056.0 9.803-610.0 9.803-616.0 9.803-618.0 8.713-286.0

1412SS 4.5 8.715-102.0 7.5 8.724-283.0 8.724-306.0 9.803-662.0 8.750-746.0 8.715-592.0 1412SS 8.715-582.0 9.802-401.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-286.0

1421SS 4.5 8.751-014.0 7.5 8.724-275.0 8.724-304.0 9.803-662.0 8.750-746.0 8.715-592.0 1421SS 8.715-582.0 9.802-401.0 8.718-056.0 9.803-610.0 9.803-616.0 9.803-618.0 8.713-286.0

1421SS-208 4.5 8.715-101.0 7.5 8.724-275.0 8.724-305.0 9.803-662.0 8.750-746.0 8.715-592.0 1421SS-208 8.715-582.0 9.802-401.0 8.718-056.0 9.803-610.0 9.803-616.0 9.803-618.0 8.713-286.0

1422SS 4.5 8.751-014.0 7.5 8.724-275.0 8.724-305.0 9.803-662.0 8.750-746.0 8.715-592.0 1422SS 8.715-582.0 9.802-401.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-286.0

1422SS-208 4.5 8.715-101.0 7.5 8.724-275.0 8.724-305.0 9.803-662.0 8.750-746.0 8.715-592.0 1422SS-208 8.715-582.0 9.802-401.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-286.0

1424SS 4.5 8.751-014.0 7.5 8.724-269.0 8.724-312.0 8.716-886.0 8.750-746.0 8.715-592.0 1424SS 8.715-582.0 9.802-401.0 8.718-056.0 9.803-610.0 9.803-616.0 9.803-618.0 8.713-080.0

1425SS 4.5 8.751-014.0 7.5 8.724-269.0 8.724-312.0 8.716-886.0 8.750-746.0 8.715-592.0 1425SS 8.715-582.0 9.802-401.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-080.0

952SS-208 5.0 8.715-128.0 6.2 8.724-280.0 8.724-306.0 9.803-662.0 8.750-749.0 8.715-593.0 952SS-208 9.802-383.0 9.802-400.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-286.0

969SS 5.0 8.715-131.0 6.2 8.724-269.0 8.724-303.0 8.716-884.0 8.750-749.0 8.715-593.0 969SS 9.802-383.0 9.802-400.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-080.0

1452SS-208 4.5 8.715-162.0 8.2 8.724-283.0 8.724-306.0 9.803-662.0 8.750-749.0 8.715-593.0 1452SS-208 9.802-383.0 9.802-400.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-286.0

1469SS 4.5 8.751-005.0 8.2 8.724-269.0 8.724-303.0 8.716-884.0 8.750-749.0 8.715-593.0 1469SS 9.802-383.0 9.802-400.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-080.0


35

PR

ES

SU

RE

WA

SH

ER

Sp

ecificatio

ns

Model Nozzle MotorMotor

HP Contractor OverloadTrans-Former Pump

PumpPulley Model

MotorPulley

MotorBushing Burner Pilot

GasValve

LPConv.

Fuse (2)

981SS 5.5 8.715-142.0 5 8.724-280.0 8.724-305.0 9.803-662.0 8.750-746.0 8.715-592.0 981SS 8.715-582.0 9.802-400.0 8.718-056.0 9.803-610.0 9.803-616.0 9.803-618.0 8.713-286.0

982SS 5.5 8.715-142.0 5 8.724-280.0 8.724-305.0 9.803-662.0 8.750-746.0 8.715-592.0 982SS 8.715-582.0 9.802-400.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-286.0

991SS 5.5 8.751-013.0 5 8.724-269.0 8.724-304.0 9.803-662.0 8.750-746.0 8.715-592.0 991SS 8.715-582.0 9.802-400.0 8.718-056.0 9.803-610.0 9.803-616.0 9.803-618.0 8.713-286.0

991SS-208 5.5 8.715-092.0 5 8.724-269.0 8.724-304.0 9.803-662.0 8.750-746.0 8.715-592.0 991SS-208 8.715-582.0 9.802-400.0 8.718-056.0 9.803-610.0 9.803-616.0 9.803-618.0 8.713-286.0

992SS 5.5 8.751-013.0 5 8.724-269.0 8.724-304.0 9.803-662.0 8.750-746.0 8.715-592.0 992SS 8.715-582.0 9.802-400.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-286.0

992SS-208 5.5 8.715-092.0 5 8.724-269.0 8.724-304.0 9.803-662.0 8.750-746.0 8.715-592.0 992SS-208 8.715-582.0 9.802-400.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-286.0

994SS 5.5 8.751-013.0 5 8.724-269.0 8.724-303.0 8.716-886.0 8.750-746.0 8.715-592.0 994SS 8.715-582.0 9.802-400.0 8.718-056.0 9.803-610.0 9.803-616.0 9.803-618.0 8.713-080.0

995SS 5.5 8.751-013.0 5 8.724-269.0 8.724-303.0 8.716-886.0 8.750-746.0 8.715-592.0 995SS 8.715-582.0 9.802-400.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-080.0

1411SS 4.5 8.715-102.0 7.5 8.724-283.0 8.724-306.0 9.803-662.0 8.750-746.0 8.715-592.0 1411SS 8.715-582.0 9.802-401.0 8.718-056.0 9.803-610.0 9.803-616.0 9.803-618.0 8.713-286.0

1412SS 4.5 8.715-102.0 7.5 8.724-283.0 8.724-306.0 9.803-662.0 8.750-746.0 8.715-592.0 1412SS 8.715-582.0 9.802-401.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-286.0

1421SS 4.5 8.751-014.0 7.5 8.724-275.0 8.724-304.0 9.803-662.0 8.750-746.0 8.715-592.0 1421SS 8.715-582.0 9.802-401.0 8.718-056.0 9.803-610.0 9.803-616.0 9.803-618.0 8.713-286.0

1421SS-208 4.5 8.715-101.0 7.5 8.724-275.0 8.724-305.0 9.803-662.0 8.750-746.0 8.715-592.0 1421SS-208 8.715-582.0 9.802-401.0 8.718-056.0 9.803-610.0 9.803-616.0 9.803-618.0 8.713-286.0

1422SS 4.5 8.751-014.0 7.5 8.724-275.0 8.724-305.0 9.803-662.0 8.750-746.0 8.715-592.0 1422SS 8.715-582.0 9.802-401.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-286.0

1422SS-208 4.5 8.715-101.0 7.5 8.724-275.0 8.724-305.0 9.803-662.0 8.750-746.0 8.715-592.0 1422SS-208 8.715-582.0 9.802-401.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-286.0

1424SS 4.5 8.751-014.0 7.5 8.724-269.0 8.724-312.0 8.716-886.0 8.750-746.0 8.715-592.0 1424SS 8.715-582.0 9.802-401.0 8.718-056.0 9.803-610.0 9.803-616.0 9.803-618.0 8.713-080.0

1425SS 4.5 8.751-014.0 7.5 8.724-269.0 8.724-312.0 8.716-886.0 8.750-746.0 8.715-592.0 1425SS 8.715-582.0 9.802-401.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-080.0

952SS-208 5.0 8.715-128.0 6.2 8.724-280.0 8.724-306.0 9.803-662.0 8.750-749.0 8.715-593.0 952SS-208 9.802-383.0 9.802-400.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-286.0

969SS 5.0 8.715-131.0 6.2 8.724-269.0 8.724-303.0 8.716-884.0 8.750-749.0 8.715-593.0 969SS 9.802-383.0 9.802-400.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-080.0

1452SS-208 4.5 8.715-162.0 8.2 8.724-283.0 8.724-306.0 9.803-662.0 8.750-749.0 8.715-593.0 1452SS-208 9.802-383.0 9.802-400.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-286.0

1469SS 4.5 8.751-005.0 8.2 8.724-269.0 8.724-303.0 8.716-884.0 8.750-749.0 8.715-593.0 1469SS 9.802-383.0 9.802-400.0 8.718-055.0 9.803-610.0 9.803-616.0 N/A 8.713-080.0

SPECIFICATIONS


OP

ER

AT

OR

’S M

AN

UA

L P

RE

SS

UR

E W

AS

HE

R

36

MT-2 SERIES PUMP EXPLODED VIEW

TORQUE SPECS

Item # Ft.-lbs

14 75

15 18

23 7.6

33 9

43 13

48 7.6

8.750-745.0 HH306R.2 Shaft Right8.750-746.0 HH406R.2 Shaft Right8.750-747.0 HH456R.2 Shaft Right8.750-748.0 HH466R.2 Shaft Right8.750-749.0 HH506R.2 Shaft Right

ITEM PART # DESCRIPTION QTY 1 8.751-216.0 Crankcase 1

2* See Kits Below Seal, Oil, Plunger 3

3* See Kits Below O-Ring, 1.78 X 31.47 3

4* See Kits Below Ring, Pressure, 20mm 3

5* See Kits Below "U" Seal, 20mm 6

6* See Kits Below Ring, Intermediate 20mm 3

7* See Kits Below "U" Seal, 20mm 3

8 9.803-199.0 Washer, Copper 1

9 9.802-926.0 Plug, Brass 1/2 1

10 8.751-219.0 Manifold Housing 1


12* See Kits Below Valve Assembly 6


14 9.802-924.0 Valve Cap 6

15 8.717-526.0 Stud, Bolt Manifold 8

16 9.802-884.0 Washer 8

MT-2 SERIES PUMP EXPLODED VIEW PARTS LIST

I TEM PART # DESCRIPTION QTY 17 9.803-198.0 Washer, Copper 1

18 9.802-925.0 Plug, 3/8 2

23 9.802-939.0 Screw Hex 8mm X 18mm 8

24 8.717-210.0 Closed Bearing Housing 1

25 9.803-192.0 O-Ring, 2.62 X 60.05 2

26 8.933-011.0 Bearing, Roller 2

27 8.751-221.0 Crankshaft (HH506R.2) 1

8.751-220.0 Crankshaft, (HH456R.2) 1

8.751-223.0 Crankshaft, (HH406R.2) 1

8.751-222.0 Crankshaft, (HH306R.2) 1

8.717-063.0 Crankshaft (HH466R.2) 1

28 9.803-167.0 Key, Crankshaft 1

29 9.802-921.0 Dipstick 1

30 9.803-140.0 Crankshaft Seal 1

31 9.803-178.0 Shim 1

32 8.717-209.0 Bearing Housing 1


37

PR

ES

SU

RE

WA

SH

ER

OP

ER

AT

OR

’S M

AN

UA

L

MT-2 SERIES PUMP EXPLODED VIEW PARTS LIST

REPAIR KIT NUMBER 8.725-362.0 8.725-407.0 8.751-238.0 8.717-584.0 8.717-618.0

KIT DESCRIPTION Seal Packing20 mm, 3 Cyl

Packing Assy.20 mm

Kit, Plunger, 20 mm Check Valve Plunger Oil

Seal

ITEM NUMBERS INCLUDED 3, 5, 7 3, 4, 5, 6, 7 33, 34, 35, 36,

37, 38 11, 12, 13 2

NUMBER OF CYLINDERS KIT WILL SERVICE 3 1 1 1 3

ITEM PART # DESCRIPTION QTY 33* See Kits Below Plunger Nut, M8 3

34* See Kits Below Spacer, Copper 3

35* See Kits Below Plunger, 20mm 3

36* See Kits Below Spacer, Copper 3

37* See Kits Below O-Ring, 1.78 x 7.66 3

38* See Kits Below Ring, Teflon 3

39 8.751-225.0 Rod, Plunger 3

40 9.803-158.0 Connecting Rod 3

41 8.751-228.0 Pin, Connecting Rod 3

42 9.803-218.0 Washer, Spring 6

43 9.803-238.0 Screw, M6 x 25 6

44 8.933-016.0 O-Ring, 2.62 X 126.67 1

45 8.751-229.0 Crankcase Cover 1

46 9.803-906.0 O-Ring, 1.78 X 14 1

47 9.803-202.0 Sight Glass, G3/4 1

48 9.802-939.0 Screw, Cover 4

* Available In Kit (See Below)


OP

ER

AT

OR

’S M

AN

UA

L P

RE

SS

UR

E W

AS

HE

R

38

VB9 UNLOADER EXPLODED VIEW AND PARTS LIST

ITEM PART # DESCRIPTION QTY

1 29.0087.51 Sst Clip 1

2 29.0089.84 Plastic Housing 1

3 16.3020.00 2.5 x 12 mm Screw 2

4 29.0088.84 Cover 1

5 10.3206.01* O-Ring, 2.62 x 28.25mm 1

6 12.5006.00 El. Cable and Microswitch 1

7 29.0109.84 Red Nut (25 Bar) 1

8 10.3169.00* O-Ring, 2.62 x 6.02 mm 1

9 10.3038.00* O-Ring, 1.78 x 3.68 mm 1

10 14.3519.00 Washer, 4 x 8 mm 1

11 60.2303.51 Spring 1

12 29.0086.31 Washer, 4 x 16 mm 1

13 60.2351.31 Pin 1

14 60.2353.31 Seat Fitting 1

15 10.3165.00* O-Ring, 2.62 x 2.84 1

16 10.4018.00* Back Ring, 3.2 x 7.5 mm 1

17 30.4115.31 M 10 Plug 1

18 60.2352.51 Sst Pin 1

19 10.3073.00* O-Ring, 1.78 x 23.52 mm 1

20 10.3072.50* O-Ring, 1.78 x 21.95 mm 1

21 10.3070.02* O-Ring, 1.78 x 18.77 mm 2

22 60.0733.35 Manifold 1

23 11.4540.00 Sst M6 Nut 1

24 60.2221.20* VB8/9 Seat and Shutter 1

25 10.3001.01* O-Ring, 1 x 4 mm 1

26 10.3066.01 O-Ring, 1.78 x 15.6 mm 1

ITEM PART # DESCRIPTION QTY

27 60.2210.31 Spacer 1

28 60.2202.51 VB 9 Piston 1

29 10.3170.08 O-Ring, 2.62 x 7.6 mm 1

30 10.4021.00 Back Ring, 11.4 x 15.9 mm 2

31 10.3175.00 O-Ring, 2.62 x 10.77mm 1

32 28.0013.31 Brass, 1/4 Bsp Plug 1

33 14.3911.00 1/4" Copper Washer 1

34 60.2201.35 VB9 Brass Body 1

35 15.1021.00 Pin 3 x 14 mm 1

36 10.3213.00 O-Ring 3 x 6 mm 1

37 60.0052.31 Check Valve 1

38 60.0053.51 Spring 1

39 60.0058.31 3/8 Bsp F Outlet Fitting 1

40 60.2203.61 4.2 mm Spring 1

41 60.2207.31 M8 Nut 1

42 60.2208.84 Spring Washer 1

43 16.2105.00 M5 x 6 mm Dowel 1

44 60.2252.31 Spring Nut 1

45 60.2253.31 Adjustment Nipple 1

46 11.4589.10 M8 Nut 1

47 16.1838.00 M4 Tc Screw 1

48 60.2251.84 Plastic Knob 1

49 14.3582.00 Washer, D 30 mm 1

50 60.2254.31 M30 Nut 1

51 29.0096.24 PR 5 pl. Housing Kit 1*KIT 8.704-548.0 VB9.01+PR5 Spare Parts Kit, 14x1 pcs

9215808.715-489.0


PR

ES

SU

RE

WA

SH

ER

WA

RR

AN

TY

Wirin

g D

iagram

39

900/1400 3 PH W/ELEC IGNITION


PR

ES

SU

RE

WA

SH

ER

W

irin

g D

iag

ram

40

900/1400 1 PH W/ELEC IGNITION

PR

ES

SU

RE

WA

SH

ER

WA

RR

AN

TY


HOTSY LIMITED NEW PRODUCT WARRANTYPRESSURE WASHERS

WHAT THIS WARRANTY COVERSAll Hotsy pressure washers are warranted by Hotsy to the original purchaser to be free from defects in materials and work-manship under normal use, for the periods specified below. This Limited Warranty is subject to the exclusions shown below, is calculated from the date of the original purchase, and applies to the original components only. Any parts replaced under this warranty will assume the remainder of the part’s warranty period.

SEVEN YEAR PARTS AND ONE YEAR LABOR WARRANTY:Components manufactured by Hotsy, such as frames, handles, top and bottom wraps, float tanks, fuel tanks, belt guards, and internal components on the oil-end of HoTsy manufactured pumps. General, AR, Liberty, Comet and swash and wobble plate pumps have a one year warranty. Heating coils have a five year warranty from date of original machine purchase.

ONE YEAR PARTS AND ONE YEAR LABOR WARRANTY:All other components, excluding normal wear items as described below, will be warranted for one year on parts and labor. Parts and labor warranty on these parts will be for one year regardless of the duration of the original component manufacturer’s part warranty.

WARRANTY PROVIDED BY OTHER MANUFACTURERS:Motors, generators, and engines, which are warranted by their respective manufacturers, are serviced through these manu-facturers’ local authorized service centers. Hotsy is not authorized and has no responsibility to provide warranty service for such components.

WHAT THIS WARRANTY DOES NOT COVERThis warranty does not cover the following items:

1. Normal wear items, such as nozzles, spray guns, discharge hoses, wands, quick couplers, seals, filters, gaskets, o-rings, packings, pistons, pump valve assemblies, strainers, belts, brushes, rupture disks, fuses, pump protec-tors.

2. Damage or malfunctions resulting from accidents, abuse, modifications, alterations, incorrect installation, improper servicing, failure to follow manufacturer’s maintenance instructions, or use of the equipment beyond its stated us-age specifications as contained in the operator’s manual.

3. Damage due to freezing, chemical deterioration, scale build up, rust, corrosion, or thermal expansion.4. Damage to components from fluctuations in electrical or water supply.5. Normal maintenance service, including adjustments, fuel system cleaning, and clearing of obstructions.6. Transportation to service center, field labor charges, or freight damage.

WHAT YOU MUST DO TO OBTAIN WARRANTY SERVICEIn order to obtain warranty service on items warranted by Hotsy, you must return the product to your Authorized Hotsy Distributor, freight prepaid, with proof of purchase, within the applicable warranty period. If the product is permanently installed, you must notify your Authorized Hotsy Distributor of the defect. your Authorized Hotsy Distributor will file a claim with Hotsy, who must subsequently verify the defect. In most cases, the part must be returned to Hotsy freight prepaid with the claim. For warranty service on components warranted by other manufacturer’s, your Authorized Hotsy Distributor can help you obtain warranty service through these manufacturers’ local authorized service centers.

LIMITATION OF LIABILITYHotsy’s liability for special, incidental, or consequential damages is expressly disclaimed. In no event shall Hotsy’s liability exceed the purchase price of the product in question. Hotsy makes every effort to ensure that all illustrations and specifica-tions are correct, however, these do not imply a warranty that the product is merchantable or fit for a particular purpose, or that the product will actually conform to the illustrations and specifications. our obligation under this warranty is expressly limited at our option to the replacement or repair at a service facility or factory designated by us, of such part or parts as inspection shall disclose to have neen defective. THE WARRANTY CONTAINED HEREIN IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. Hotsy does not authorize any other party, including authorized Hotsy Distributors, to make any representation or promise on behalf of Hotsy, or to modify the terms, conditions, or limitations in any way. It is the buyer’s responsibility to ensure that the installation and use of Hotsy products conforms to local codes. While Hotsy attempts to assure that its products meet national codes, it cannot be responsible for how the customer chooses to use or install the product. some states do not al-low limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

HOTSYwww.hotsy.com

Form #8.914-405.0 • Revised 9/11 • Printed in U.S.A.

If you need service on your pressure washer, contact your local Hotsydealer or visit www.Hotsy.com. Smart phone users scan the code below to

link directly to the Service Request page.

OPERATING INSTRUCTIONS OPERATOR’S MANUAL

Documents

Transcript of OPERATING INSTRUCTIONS OPERATOR’S MANUAL