OPERATING INSTRUCTIONS...OPERATING INSTRUCTIONS OXYGEN/ACETYLENE CUTTING AND WELDING KIT . WARNING:...

OPERATING INSTRUCTIONS

OXYGEN/ACETYLENECUTTING AND WELDING KIT

WARNING: There are a number of inherent hazards in the use of oxy-fuel welding and cutting apparatus. It is therefore necessary that proper safety and operating procedures be understood prior to the use of such apparatus. Please read this booklet thoroughly and carefully before attempting to operate oxy-fuel welding and cutting apparatus. A thorough understanding of the proper safety and operating procedures will serve to minimise the hazards.

This booklet is presented as a guide only to the safe and efficient operation of oxy-fuel welding, cutting and heating apparatus.

This Oxygen/Acetylene Cutting and Welding Kit should only be used by Operators who are properly trained and qualified in the safe use of this type of equipment.

!

TABLE OF CONTENTS

Safety Precautions 3-4Page

Oxygen/Acetylene Cutting and Welding Kit Contents 4

Setting up the Gas Cylinders 5

Setting up the Gas Regulators 6-8

Setting up and operation for welding application 8-11

Welding Technique 12

Welding Procedures 12-14

Heating 14

Pressure Chart for Multi-Flame Oxygen/Acetylene Nozzles 14

Setting up and operation for cutting application 14-16

Cutting Technique 17-18

Welding Tip Data Charts 18

Operational and Performance Data 19

The parts of a Cutting Attachment and Brass Handle 20

The parts of a Regulator 21

Spare parts of a Regulator 21

Warranty 22

SAFETY PRECAUTIONSFlashback occurs when the flame burns back into the torch, and sustains itself within the mixer tube. This is caused by overheating the tip and torch mixer tube by “backfiring”.

A shrill hissing or squealing noise will accompany a sustained flashback. Extinguish the flashback immediately by shutting off the preheat oxygen valve. Without oxygen the flame cannot burn inside the torch.

For safe operation:• NEVER use oil or grease around, or on any part of welding or cutting apparatus.

Even a trace of oil or grease can cause a serious fire or explosion• DO NOT use oxygen pneumatic tools to blow out lines or to dust off clothing• NEVER convert a fuel regulator for oxygen use or vice versa. The same applies for hoses• DO NOT try to use a gas cylinder without a suitable pressure reducing regulator• NEVER stand directly in front of an oxygen regulator when you are turning on the

cylinder valve• DO NOT open an oxygen cylinder valve quickly. Turn the cylinder valve on very slowly

until the maximum cylinder pressure registers on the regulator gauge. Then open the valve completely

• DO NOT open a cylinder valve until the regulator adjusting knob has been released.• NEVER attach new or used hose to the torch without first blowing out the dust which

otherwise may clog the torch• DO NOT use worn, patched or multi-spliced hose that may leak or cause excessive loss

of pressure. NEVER repair hose with friction tape, use proper hose splicers• DO NOT open the fuel gas valve more than one turn• NEVER test for gas leaks with a flame. Use soap and water• DO NOT use undue force in trying to open or close a cylinder valve. Notify your gas

supplier and have the cylinder replaced if valve is too tight or otherwise faulty• OBSERVE fire prevention precautions and have a fire extinguisher handy at all times• DO NOT try to fill a small cylinder from a large one. The operation is dangerous and

requires specialised equipment• NEVER heat a gas cylinder by placing a flame on the cylinder walls. It could cause the

cylinder to explode• DO NOT weld or cut without proper eye protection• DO NOT try to repair torches or regulators unless you have been properly instructed.

A wrong repair job can use a serious explosion

Page 3

KIT CONTENTSWeldcorp’s Oxygen/Acetylene Cutting and Welding Kit includes:• Torch handle• Cutting attachment• Oxygen regulator• Acetylene regulator• Welding nozzles (No. 8, 10, 12)• Flashback arrestors (x2 regulator & x2 torch) • Mixer• Cutting nozzle (No. 12)• Twin hose: 15FT x 1/4• Tip cleaner• Welding goggles• Single spark lighter• Plastic Toolbox

• KEEP sparks away from hoses and cylinders• DO NOT make a guess if you do not know. Get the correct answer from a qualified

person• DO NOT misuse your welding or cutting equipment, they are precision tools and will

serve you a long time if properly used• CLEAN tips regularly with the cleaner supplied• DO NOT attempt to cut or weld petrol tanks

Page 4

SETTING UP THE GAS CYLINDERSOxygen/Acetylene is the most commonly used combination of gases for welding and cutting. Oxygen is available in seamless steel cylinders, compressed to about 25,000 kPa. Standard size cylinders include 1.8m3, 3.7m3 and up to 7.5m3 capacities.

Acetylene is the most important fuel gas, because of its high flame temperature. Acetylene is generally available in clinders of approximately 1.5m3, 3.7m3 and up to 7.5m3 at a pressure of about 1,725 kPa. Acetylene cylinders are painted maroon and oxygen cylinders black.

1. Place the oxygen and fuel gas cylinders together where they are to be used and secure them from falling.

Page 5

2.

3.

After securely positioning the cylinders, remove the plastic dust cap inserted in the oxygen cylinder valve. The cylinder valve threads are examined and cleaned at the point of refilling and therefore are supplied in good condition. Use of any cloth to further clean the valve threads should not be necessary. In fact, if any cloth with oil or grease traces is used, it could prove very dangerous.

Slightly open (called “cracking”) the oxygen and fuel gas cylinder valves to make sure they do not stick and to blow out any dirt or dust lodged in the valve. Close the valve.

SETTING UP THE REGULATORS4.

5.

Be sure that the regulator inlet connection is absolutely clean and free of all traces of dirt, grease, etc. Mount the oxygen regulator to the oxygen cylinder valve using the open end spanner of the correct size. Do not use excessive force, but tighten the regulator connection nut firmly.

NOTE: Be sure the regulator adjusting knob is in the “out” position. The adjusting knob is turned anti-clockwise to release the tension on the regulating spring. Failure to do this could damage the regulator.

Open the oxygen cylinder valve SLOWLY so that the high pressure regulator gauge needle moves up slowly.

A pressure of approximately 25,000 kPa will be registered (if the cylinder is full). Never stand directly in front of, or behind, a regulator when an oxygen valve is being opened. Stand to one side. After full pressure has been reached the valve should be opened one full turn. Should the valve or connection leak immediately close the valve again and notify the supplier.

NOTE: Never use force on a cylinder value to either open or close it. If the valve will not open or close by hand notify the supplier and have the cylinder replaced.

Mount the fuel gas (acetylene) regulator in the same manner as you did the oxygen regulator, noting that the connecting nut has a left hand thread.

SETTING UP THE REGULATORS

NOTE: It is extremely important that before opening the gas cylinder valves with the regulators attached, you must always ensure the regulator control knobs are fully wound in the anti-clockwise position. Slowly open the cylinder valves so that the high pressure gauge needle moves up gradually. Never open the cylinder valves suddenly. Check for leaks. Failure to follow these measures will result in damage to both the diaphragm and gauges and void you warranty.

Connect the oxygen hose to the outlet of the oxygen regulator. The oxygen hose has “right” hand threaded connections. Turn the adjusting screw on the regulator clockwise until a reading of 35kPa shows on the low pressure gauge. Allow the oxygen to escape until you are sure the hose is clean on the inside. A new hose may have talcum powder in it to protect the hose lining whilst in storage. Dust, dirt and talcum power, if left in the hose, may enter the small gas passages in the torch and block them. This can lead to flashback.

NOTE: Oxygen assists in the burning process. Do not allow free oxygen to flow for longer than is necessary

6.

SETTING UP THE REGULATORS

SETTING UP & OPERATION FOR WELDING APPLICATION

Connect the fuel gas hose to the fuel gas regulator outlet*. The fuel gas hose has “left” handed thread connection. Blow out the hose in the same manner as with the oxygen hose. Remember, fuel gas will burn. Keep it away from flames whilst blowing out the hose.

*NOTE: It is important to note that Acetylene Hoses, Regulators, Gauges and Flashback Arrestors CANNOT be interchanged with Propane Hoses, Regulators, Gauges & Flashback Arrestors.

Connect the free ends of the oxygen and fuel gas hoses to the welding torch you are to use.

NOTE: Torch connections are clearly marked “oxy” or “gas”.

Use of Flashback Arrestors (a safety device for use with fuel gases and oxygen) is highly recommended at all times.

In Australian workplaces, it is mandatory that Flashback Arrestors are fitted at all times. These must conform to AS-4603-1999 and be tested at a minimum interval of every 12 months. Refer to the Australian standard for further information.

6.1

7.

SETTING UP & OPERATION FOR WELDING APPLICATIONNOTE: Install flashback arrestors which are clearly marked:• Oxygen regulator• Oxygen torch• Acetylene regulator• Acetylene torch

Flashback arrestors should be connected between the hose and each regulator and between the hose and the torch in the correct direction of flow which is clearly marked on the flashback arrestors.

DO NOT OVER TIGHTEN AND CHECK FOR LEAKS AFTER INSTALLATION

Assemble the appropriate mixer to the forward block of the torch handle. Note that the cone end of this mixer is provided with two sealing rings. A hand tight fit is all that is necessary for a gas tight joint.

Select the tip size that is suitable for the job you are to do. Refer to the Welding Tip Selection Chart on page 18 of this manual.

Open both oxygen and fuel gas cylinder valves in one complete turn. Partially open the torch oxygen valve and adjust the oxygen regulator until the pressure corresponds to the tip you have selected. Refer to the Welding Tip Size Pressures and Application Data on page 18 and 19 of this manual.

Close the torch oxygen valve. Partially open the torch fuel gas valve and adjust the regulator pressure, using the chart similar to how the oxygen pressure was adjusted. Close the fuel gas valve.

NOTE: Observe that the regulator pressure rises slightly when the torch valves are closed. This is the reason for setting the regulator at required pressure with the valve open. All pressure in welding and cutting charts are flowing pressures with torch valves open.

9.

10.

11.

8.


NOTE: THE FOLLOWING INSTRUCTIONS COVER THE TORCH ADJUSTMENT PROCEDURES FOR ACETYLENE ONLY.

Hold the torch in one hand and the flint lighter in the other.

Open the torch fuel gas valve approximately 1/2 turn and ignite the acetylene. Be sure to direct the flame away from persons, the cylinder or any flammable materials.

Keep opening the fuel gas valve until the flame stops smoking an leaves the end of the tip about 3mm, and then reduce slightly to bring the flame back to the tip.

Open the torch oxygen valve until a bright inner cone appears on the flame. The point at which the feathery edges of the flame disappear and a sharp inner cone is visible is called the “Neutral Flame”. Keep adjusting the torch oxygen valve back and forth until you see a Neutral Flame.

12.

13.

14.

15.



An “Oxidising Flame” is the flame that has an excess of oxygen. It is a pale blue colour without a clearly defined inner cone.

The “Carburising Flame” is the flame you get before reaching the “Neutral Flame”. It is distinguished by its black carburising feather.

WELDING TECHNIQUETwo techniques can be employed for oxygen acetylene fusion welding - forehand or backhand. The forehand technique is usually recommended for welding material up to 3mm thickness because of better control of the smaller weld puddle, while backhand welding is generally more suitable for material 3mm and thicker.

Increased speeds are possible with backhand welding and better control of the fusion at the root of the weld is normally achieved.

WELDING PROCEDURESSeveral factors are common to all metals. Probably the most important of these is the expansion of metals on heating and contraction on cooling. When welding steel plates of relatively small size, allowances must be made for closing of the joint gap as the welding progresses.

For steel, the gap of the weld joints should gradually increase by some 5mm in every 300mm. For copper and aluminium, the allowance should be larger than for steel, about in proportion to the coefficients of expansion for these metals as compared with steel. When welding assemblies, where alignment is important, the joints should be tack welded at frequent intervals.

Good workmanship demands full penetration to the bottom of the joint and complete fusion along the sides of the joint. A reinforced bead, where applied should be of good contour and there should be no undercut along the sides of the weld bead profile.

In the forehand technique, the welding rod precedes the tip in the direction in which the weld is being made. The flame is pointed in the direction of the welding, and is directed downward at an angle which preheats the edged of the joint. The torch tip and welding road are manipulated with oscillating motions to distribute the heat and molten metal uniformly.

In the backhand welding, the torch tip precedes the rod in the direction of the welding, and the flame is pointed towards the molten pool and completed weld. The end of the welding rod is placed in the flame between the tip and weld. Less manipulation is required in backhand welding than in forehand welding. The rod may be merely rolled from side to side or in semi-circles within the pool. The torch is usually held steady with little or no motion across the weld, while advancing slowly and evenly along the seam to be welded.

16.

17.

WELDING PROCEDURES cont.Practically all fusion welding of ductile materials, such as wrought iron and alloy steels is performed in the same manner as that of low and medium carbon steels. Thus, the procedures recommended for these materials may be used as a guide for welding other materials where no specific instructions can be obtained.

In the production of satisfactory joints, a slightly carburising flame can be used. The adjustment of the oxy-acetylene flame is simple and maybe maintained by observing the characteristics of the flame. The proper adjustment of the flame for other types of fuel gases is more difficult as no marked visible change in flame characteristics may occur.

The outer envelope of the flame, not the inner cone, should be applied to the work.

The Braze Welding technique is different from the one used in gas fusion welding. Torch preheating of adjacent material will depend upon size, shape and thermal conductivity of the metals and the joint configuration. Improper heating, primarily due to poor manipulation of the torch, may cause cracking, overheating and / or oxidation of the filler metal, as well as incomplete joint penetration. It is important that the joint be brought to a uniform temperature within the brazing temperature range that the filler metal flows freely and fills the joint. Overheating must be avoided and this is best accomplished by using an appropriate flux with a melting point not too far below the brazing temperature range of the filler metal.

The melting of the flux can then serve as an indicator of the proper brazing temperature range of the filler metal. If the brazing filler metal is to be face-fed, it is touched to the joint as the heating progresses, until it melts and flows freely through the joint.

Heating should then be stopped. This technique makes the joint area itself in effect a “soldering iron” and overheating is avoided. It is poor practice to apply the torch flame directly to the filler metal or flux for the purpose of force melting or flowing.

It is advisable to maintain a uniform temperature at the joint. To accomplish this, auxiliary or multiple tip and multi flame torches may be necessary. In mechanised operations the parts can be moved, oscillated or rotated as they pass through the heating zone. Alternatively, the flames are moved around the parts to be brazed. In some operations, torches or burners are used to heat the parts over the entire joint area. In any case, the purpose is to obtain and maintain uniformity of metal temperature.

WELDING PROCEDURES cont.The filler metal is most commonly face-fed in manual torch brazing operations. In mechanised operations, proper design will permit the use of the pre-placed filler metal in the form of rings, washers, shims, paste or powder. However the pre-places filler metal should be positioned with respect to the flame so as not to be prematurely melted.

SETTING UP & OPERATION FOR CUTTING APPLICATION

The preparation, flame adjustment and operation of the heating torch (nozzle) are the same as for welding. Brazing techniques utilising the multi-flame nozzle are described on the previous pages.

The techniques for heating parts vary greatly and will depend upon metal, dimension, shape etc. However, the basic objectives of heating metal to uniform temperature are the same.

Fit the cutting attachment to the torch handle. The cutting attachment cone end fits the welding torch head in the same manner as the welding tip mixer; hand tight with sealing rings. Connect hoses in the same manner as done with the welding torch. Select the type and size of cutting tip suitable to the work in hand and be sure the seating cone of the tip is not damaged and is free from all dirt before inserting into cutting attachment head. The cutting tip should be secured with a spanner using firm, but not excessive force. Fully open the oxygen valve on the welding torch handle.

18.

19.

RECOMMENDED PRESSURE CHART FOR MULTI-FLAME OXYGEN/ACETYLENE NOZZLES

HEATING

SETTING UP & OPERATION FOR CUTTING APPLICATIONThe lever actuated valve controls the cutting oxygen, which passes through the centre orifice of the tip.

NOTE: Refer to the chart on page 19 of this manual for cutting tip section


Before lighting the torch, set the regulator pressure for each gas (using the pressure chart found on page 19 of this manual

IMPORTANT: Always purge out the cutting oxygen passages by pressing the cutting oxygen lever before lighting the torch.

Open the fuel valve approximately 1/2 turn and ignite the gas with a flint lighter. Adjust the fuel valve until flame clears the end of the tip by about 3mm, and then reduce slightly to return the flame to the tip.

Slowly open the preheat oxygen valve of the cutting attachment until a neutral flame has been established, depress the cutting oxygen lever. Note that the preheat flames changes slightly from the neutral setting. With the cutting oxygen level pressed readjust the preheat oxygen valve until the preheat flames are neutral again.

IMPORTANT: Check where the molten metal and sparks land from cutting or welding. Serious fires and explosions have been caused by careless torch operations. TAKE ALL POSSIBLE PRECAUTIONS - have a fire extinguisher available - remove or protect flammable substances including: oxygen and acetylene hoses before starting work.

19.1

20.

21.

SETTING UP & OPERATION FOR CUTTING APPLICATION


Direct the inner cone of the preheat flames onto the spot where the cut is to be established, with the inner cones just clear of the surface. Take your time. Hold steady. Before the cutting action can start the steel must be preheated to a bright cherry read. When the red spot appears, slowly press the cutting oxygen lever.

NOTE: If the lever is pressed too soon the flow of oxygen will chill the preheated area and prevent cutting.

When the cut has started, move the torch in the direction you wish to cut. Move too fast and you will lose the cut. Move too slow and the metal will fuse together.

NOTE: The patch of the cut can be marked with chalk or centre punch marks. Hold the torch so that the cone ends of the preheat flames just clear of the metal. Hold the tip at right angles to work for straight cuts at the desired angle for bevel cuts. Take your time and do not move too fast or too slowly. Keep the tip out of the molten metal.

To pierce metal, hold the torch so that the preheat flame just clears the work. When the spot becomes a bright cherry red press down slowly on the oxygen cutting lever.

To prevent the sparks and the slag blowing toward you, tilt the torch tip slightly to one side so the sparks blow away from you and draw the torch head up slightly from work. When the metal is pierced, move the torch head steadily in the direction you wish to cut. If the metal does not pierce all the way through then not enough cutting oxygen is being used.

22.

23.

24.

25.

CUTTING TECHNIQUEProcess of flame cuttingFlame cutting of ferrous metals is primarily a chemical affinity of oxygen for ferrous metals above ignition temperatures. It is a process of preheating the material to be cut to its ignition temperature then rapidly oxidising it by means of a stream of oxygen issuing from a cutting tip. The jet forms a narrow slot or KERF in the metal. In addition to the chemical reaction, there is a very helpful mechanical eroding effect produced by the energy of the cutting oxygen stream which washes away approximately 30% of the metal in molten, unconsumed metallic form. After the cutting action starts, the torch unit is conveyed across the material to be cut at a speed sufficient to produce a continuous cutting action. This motion may be accomplished either manually or mechanically (with an automatic line or profile cutting machine).

In manual cutting operations, the cutting tip is directed so the preheat flames and cutting jet stream concentrate in the area to be pierced or severed. Where a better quality of cut is desired, the operator may employ a guide for the torch to maintain a given tip-to-work distance and to move the torch along a given path evenly. A roller or wheel guide may also be employed to support the head of the torch, thereby leaving the operator free to direct the torch, at a fairly regular speed, along the line of cut. For cutting circles, a radius rod circle cutting attachment may be employed.

When you finish your welding or cutting operation1. First shut off the torch fuel gas valve, then shut off the torch oxygen valve. If this procedure

is reversed a “pop” may occur. This “pop” throws carbon soot back into the torch and may, in time, partially block it.

2. Close both cylinder valves3. Open the torch oxygen valve and let the oxygen lines drain out4. Release the adjusting screw on the oxygen regulator5. Open the torch fuel valve and release the pressure in the line6. Release the adjusting screw on the fuel gas regulator

Remember to set welding torch pressures according to the chart using approximately equal pressures. Sufficient pressure should be used at all times to ensure a dependable flame and freedom from “popping”. Excessive pressures generally waste gas more than they speed up the work. Ensure you use the right size tip for each job.

CUTTING TECHNIQUEBackfire and FlashbackBackfire is a large “pop” or rattle caused by any of the following:• Touching the work with the tip• Operating the torch at a low fuel gas pressure• A loose tip• Dirt on the seating surface of the tip, mixer or head, causing a leak• Overheating the tip

WELDING TIP DATA CHARTS

Tip Sizes 6-32 Tip Sizes 8x12

OPERATIONAL & PERFORMANCE DATA

The

Part

s of

a C

utti

ng A

ttac

hmen

tTh

e Pa

rts

of a

Bra

ss H

andl

e

The

Part

s of

a R

egul

ator

OXY-ACETYLENE WELDING & CUTTING KITRegulator Spare Parts List

DiagramReferenceNumber

OxygenRegulator

AcetyleneRegulatorPart Description

1 YEAR WARRANTYSubject to the warranty conditions below, this Weldcorp product (“the Product”) is warranted by Cyclone Tools Pty Ltd (“the Company”) to be free from defects in material or workmanship for a period of 12 months from the date of original purchase (“the Warranty Period”).

Under this warranty, the Company will, subject to the conditions below and at the Company’s option, repair or replace the Product, or refund the purchase price of the Product, if such a defect becomes apparent during the Warranty Period.

In the event of such a defect, the Product must be returned to the place of purchase, together with proof of purchase. Any handling and transportation (and other expenses) incurred in claiming under this warranty are not covered by this warranty and will not be borne by the Company.

The Company’s dealers or agents are not permitted to offer any warranty or guarantee on the Company’s behalf in relation to the Product, except as expressly stated in this warranty.

The Company’s obligations under this warranty are subject to: (a) the Product having been used in accordance with the Company’s directions, instructions and recommendations; (b) the Product having been used under normal conditions and with reasonable care (including in relation to the maintenance of the Product); (c) the Product not having been altered, tampered with or otherwise dealt with by any person in a manner other than as intended in respect of the Product. For the avoidance of doubt, this warranty does not cover damage, malfunction or failure resulting from misuse, neglect, abuse, or where the Product has been used for a purpose for which it was not designed or is not suited, or if repairs, alterations or modifications have been attempted by a person who is not an Authorised Service Agent of the Company. This warranty also does not apply to accidental damage or normal wear and tear.

In addition to other rights and remedies that may be available under law, our goods come with guarantees that cannot be excluded under Australian Consumer Law (for consumers in Australia) and the Consumer Guarantees Act (for consumers in NZ). If you are a consumer in Australia, you are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. If you are consumer in New Zealand, we will comply with our obligations to you under the Consumer Guarantees Act.

Cyclone Tools Pty Ltd73C Elizabeth StreetWetherill Park, New South Wales, 2164AustraliaPh: 1800 011 812 Email: [email protected]

Manufactured in ChinaCyclone Tools Pty LtdABN 89 169 427 06173C Elizabeth Street

Wetherill Park NSW 2164www.weldcorp.com.au

AUS Helpline: 1800 011 812

OPERATING INSTRUCTIONS...OPERATING INSTRUCTIONS OXYGEN/ACETYLENE CUTTING AND WELDING KIT . WARNING:...

Documents

Transcript of OPERATING INSTRUCTIONS...OPERATING INSTRUCTIONS OXYGEN/ACETYLENE CUTTING AND WELDING KIT . WARNING:...