Operating instructions G · 11 11.14 DE A Correct Use and Application 1 General The industrial...

10.07 -

11.14

51054863

ERE 225

Operating instructions G

11.1

4 D

E

4

11.1

4 D

E

4

5

11.1

4 D

E

Foreword

Notes on the operating instructions

The present ORIGINAL OPERATING INSTRUCTIONS are designed to providesufficient instruction for the safe operation of the industrial truck. The information isprovided clearly and concisely. The chapters are arranged by letter and the pages arenumbered continuously.

The operator manual details different industrial truck models. When operating andservicing the industrial truck, make sure that the particular section applies to yourtruck model.

Our trucks are subject to ongoing development. Jungheinrich reserves the right toalter the design, equipment and technical features of the system. No guarantee ofparticular features of the truck should therefore be assumed from the presentoperating instructions.

Safety notices and text mark-ups

Safety instructions and important explanations are indicated by the followinggraphics:

DANGER!

Indicates an extremely hazardous situation. Failure to comply with this instruction willresult in severe irreparable injury and even death.

WARNING!

Indicates an extremely hazardous situation. Failure to comply with this instructionmay result in severe irreparable injury and even death.

CAUTION!

Indicates a hazardous situation. Failure to comply with this instruction may result inslight to medium injury.

NOTE

Indicates a material hazard. Failure to comply with this instruction may result inmaterial damage.

Z Used before notices and explanations.

t Indicates standard equipmento Indicates optional equipment

5

11.1

4 D

E

Foreword

Notes on the operating instructions

The present ORIGINAL OPERATING INSTRUCTIONS are designed to providesufficient instruction for the safe operation of the industrial truck. The information isprovided clearly and concisely. The chapters are arranged by letter and the pages arenumbered continuously.

The operator manual details different industrial truck models. When operating andservicing the industrial truck, make sure that the particular section applies to yourtruck model.

Our trucks are subject to ongoing development. Jungheinrich reserves the right toalter the design, equipment and technical features of the system. No guarantee ofparticular features of the truck should therefore be assumed from the presentoperating instructions.

Safety notices and text mark-ups

Safety instructions and important explanations are indicated by the followinggraphics:

DANGER!

Indicates an extremely hazardous situation. Failure to comply with this instruction willresult in severe irreparable injury and even death.

WARNING!

Indicates an extremely hazardous situation. Failure to comply with this instructionmay result in severe irreparable injury and even death.

CAUTION!

Indicates a hazardous situation. Failure to comply with this instruction may result inslight to medium injury.

NOTE

Indicates a material hazard. Failure to comply with this instruction may result inmaterial damage.

Z Used before notices and explanations.

t Indicates standard equipmento Indicates optional equipment

11.1

4 D

E

6

Copyright

Copyright of these operating instructions remains with JUNGHEINRICH AG.

Jungheinrich Aktiengesellschaft

Am Stadtrand 3522047 Hamburg - Germany

Tel: +49 (0) 40/6948-0

www.jungheinrich.com

11.1

4 D

E

6

Copyright

Copyright of these operating instructions remains with JUNGHEINRICH AG.

Jungheinrich Aktiengesellschaft

Am Stadtrand 3522047 Hamburg - Germany

Tel: +49 (0) 40/6948-0

www.jungheinrich.com

7

11.1

4 D

E

Contents

A Correct Use and Application ................................................... 11

1 General.................................................................................................... 112 Correct application................................................................................... 113 Approved application conditions.............................................................. 114 Proprietor responsibilities ........................................................................ 125 Adding attachments and/or accessories.................................................. 12

B Truck Description .................................................................... 13

1 Application ............................................................................................... 132 Assemblies and Functional Description................................................... 142.1 Assembly Overview ................................................................................. 142.2 Functional Description ............................................................................. 153 Technical Specifications .......................................................................... 173.1 Performance data .................................................................................... 173.2 Dimensions.............................................................................................. 183.3 Weights.................................................................................................... 233.4 Tyre type.................................................................................................. 233.5 EN norms................................................................................................. 243.6 Conditions of use..................................................................................... 243.7 Electrical requirements ............................................................................ 243.8 Identification points and data plates ........................................................ 25

C Transport and Commissioning ................................................ 29

1 Lifting by crane ........................................................................................ 292 Transport ................................................................................................. 303 Using the Truck for the First Time ........................................................... 31

D Battery - Servicing, Recharging, Replacement ....................... 33

1 Safety Regulations Governing the Handling of Lead-Acid Batteries ....... 332 Battery types............................................................................................ 353 Exposing the battery................................................................................ 364 Charging the battery ................................................................................ 375 Battery removal and installation .............................................................. 385.1 Removing the battery from the top .......................................................... 395.2 Removing the battery from the side......................................................... 40

7

11.1

4 D

E

Contents

A Correct Use and Application ................................................... 11

1 General.................................................................................................... 112 Correct application................................................................................... 113 Approved application conditions.............................................................. 114 Proprietor responsibilities ........................................................................ 125 Adding attachments and/or accessories.................................................. 12

B Truck Description .................................................................... 13

1 Application ............................................................................................... 132 Assemblies and Functional Description................................................... 142.1 Assembly Overview ................................................................................. 142.2 Functional Description ............................................................................. 153 Technical Specifications .......................................................................... 173.1 Performance data .................................................................................... 173.2 Dimensions.............................................................................................. 183.3 Weights.................................................................................................... 233.4 Tyre type.................................................................................................. 233.5 EN norms................................................................................................. 243.6 Conditions of use..................................................................................... 243.7 Electrical requirements ............................................................................ 243.8 Identification points and data plates ........................................................ 25

C Transport and Commissioning ................................................ 29

1 Lifting by crane ........................................................................................ 292 Transport ................................................................................................. 303 Using the Truck for the First Time ........................................................... 31

D Battery - Servicing, Recharging, Replacement ....................... 33

1 Safety Regulations Governing the Handling of Lead-Acid Batteries ....... 332 Battery types............................................................................................ 353 Exposing the battery................................................................................ 364 Charging the battery ................................................................................ 375 Battery removal and installation .............................................................. 385.1 Removing the battery from the top .......................................................... 395.2 Removing the battery from the side......................................................... 40

11.1

4 D

E

8

E Operation ................................................................................ 41

1 Safety Regulations for the Operation of the Forklift Truck....................... 412 Displays and Controls.............................................................................. 432.1 Battery discharge indicator ...................................................................... 463 Starting up the truck ................................................................................ 473.1 Checks and operations to be performed before starting daily operation . 473.2 Preparing the truck for operation ............................................................. 483.3 Parking the truck securely ....................................................................... 493.4 Battery discharge monitor........................................................................ 494 Industrial Truck Operation ....................................................................... 504.1 Safety regulations for truck operation...................................................... 504.2 Emergency Disconnect, Travel, Steering, Braking .................................. 524.3 Lifting, transporting and depositing loads ................................................ 585 Troubleshooting....................................................................................... 615.1 Truck does not start ................................................................................. 615.2 Load cannot be lifted ............................................................................... 616 Operating the truck without its own drive system .................................... 637 Optional equipment ................................................................................. 657.1 CanCode keypad..................................................................................... 657.2 Setting the truck parameters with CanCode............................................ 707.3 Traction controller AS2412i parameters .................................................. 727.4 AS2412iS combi controller parameters ................................................... 777.5 CanDis display instrument....................................................................... 847.6 ISM access module (o)........................................................................... 857.7 Curve Control .......................................................................................... 85

F Industrial Truck Maintenance .................................................. 87

1 Operational Safety and Environmental Protection................................... 872 Maintenance Safety Regulations............................................................. 873 Servicing and Inspection ......................................................................... 924 Maintenance checklist ERE 225 fixed platform ....................................... 934.1 Proprietor................................................................................................. 934.2 Customer Service .................................................................................... 945 Maintenance checklist ERE 225 folding platform .................................... 985.1 Proprietor................................................................................................. 985.2 Customer Service .................................................................................... 996 Lubricants and Lubrication Schedule ...................................................... 1036.1 Handling consumables safely.................................................................. 1036.2 Lubrication Schedule ............................................................................... 1056.3 Consumables........................................................................................... 1067 Maintenance and repairs ......................................................................... 1077.1 Preparing the truck for maintenance and repairs .................................... 1077.2 Replacing the drive wheel ....................................................................... 1087.3 Checking the hydraulic oil level ............................................................... 1087.4 Removing the front panel ........................................................................ 1087.5 Checking electrical fuses......................................................................... 1107.6 Restoring the truck to service after maintenance and repairs ................. 1128 Safety tests to be performed at intervals and after unusual incidents ..... 1139 Decommissioning the industrial truck ...................................................... 114

11.1

4 D

E

8

E Operation ................................................................................ 41

1 Safety Regulations for the Operation of the Forklift Truck....................... 412 Displays and Controls.............................................................................. 432.1 Battery discharge indicator ...................................................................... 463 Starting up the truck ................................................................................ 473.1 Checks and operations to be performed before starting daily operation . 473.2 Preparing the truck for operation ............................................................. 483.3 Parking the truck securely ....................................................................... 493.4 Battery discharge monitor........................................................................ 494 Industrial Truck Operation ....................................................................... 504.1 Safety regulations for truck operation...................................................... 504.2 Emergency Disconnect, Travel, Steering, Braking .................................. 524.3 Lifting, transporting and depositing loads ................................................ 585 Troubleshooting....................................................................................... 615.1 Truck does not start ................................................................................. 615.2 Load cannot be lifted ............................................................................... 616 Operating the truck without its own drive system .................................... 637 Optional equipment ................................................................................. 657.1 CanCode keypad..................................................................................... 657.2 Setting the truck parameters with CanCode............................................ 707.3 Traction controller AS2412i parameters .................................................. 727.4 AS2412iS combi controller parameters ................................................... 777.5 CanDis display instrument....................................................................... 847.6 ISM access module (o)........................................................................... 857.7 Curve Control .......................................................................................... 85

F Industrial Truck Maintenance .................................................. 87

1 Operational Safety and Environmental Protection................................... 872 Maintenance Safety Regulations............................................................. 873 Servicing and Inspection ......................................................................... 924 Maintenance checklist ERE 225 fixed platform ....................................... 934.1 Proprietor................................................................................................. 934.2 Customer Service .................................................................................... 945 Maintenance checklist ERE 225 folding platform .................................... 985.1 Proprietor................................................................................................. 985.2 Customer Service .................................................................................... 996 Lubricants and Lubrication Schedule ...................................................... 1036.1 Handling consumables safely.................................................................. 1036.2 Lubrication Schedule ............................................................................... 1056.3 Consumables........................................................................................... 1067 Maintenance and repairs ......................................................................... 1077.1 Preparing the truck for maintenance and repairs .................................... 1077.2 Replacing the drive wheel ....................................................................... 1087.3 Checking the hydraulic oil level ............................................................... 1087.4 Removing the front panel ........................................................................ 1087.5 Checking electrical fuses......................................................................... 1107.6 Restoring the truck to service after maintenance and repairs ................. 1128 Safety tests to be performed at intervals and after unusual incidents ..... 1139 Decommissioning the industrial truck ...................................................... 114

9

11.1

4 D

E9.1 Before taking the truck out of service ...................................................... 1149.2 Action to be taken during decommissioning ............................................ 1159.3 Restoring the truck to service after decommissioning ............................. 11610 Final de-commissioning, disposal............................................................ 11611 Human vibration measurement ............................................................... 117

9

11.1

4 D

E

9.1 Before taking the truck out of service ...................................................... 1149.2 Action to be taken during decommissioning ............................................ 1159.3 Restoring the truck to service after decommissioning ............................. 11610 Final de-commissioning, disposal............................................................ 11611 Human vibration measurement ............................................................... 117

11.1

4 D

E

10

11.1

4 D

E

10

1

0506

.GB

Appendix

JH Traction Battery Operating Instructions

Z These operating instructions apply only to Jungheinrich battery models. If usinganother brand, refer to the manufacturer's operating instructions.

1

0506

.GB

Appendix

JH Traction Battery Operating Instructions

Z These operating instructions apply only to Jungheinrich battery models. If usinganother brand, refer to the manufacturer's operating instructions.

0506

.GB

2

0506

.GB

2

11

11.1

4 D

E

A Correct Use and Application

1 General

The industrial truck described in the present operating instructions is designed forlifting, lowering and transporting load units.It must be used, operated and serviced in accordance with the present instructions.Any other type of use is beyond the scope of application and can result in damage topersonnel, the industrial truck or property.

2 Correct application

NOTE

The maximum load and load distance are indicated on the load chart and must not beexceeded.The load must rest on the load handler or be lifted by an attachment approved by themanufacturer.The load must rest on the back of the fork carriage and centrally between the forks.

– Lifting and lowering of loads.– Transporting lowered loads.– Do not carry or lift passengers.– Do push or pull load units.

3 Approved application conditions

– Operation in industrial and commercial environments.– Permissible temperature range -10°C to 40°C.– Operation only on secure, level surfaces with sufficient capacity.– Operation only on routes that are visible and approved by the proprietor.– Inclines of max. 8 % may be negotiated with load, and 16 % without load.– Do not travel across or at an angle on inclines. Travel with the load facing uphill.– Operation in partially public traffic.

Z Special equipment and authorisation are required if the truck is to be used inextreme conditions.The truck is not authorised for use in areas at risk of explosion.

11

11.1

4 D

E

A Correct Use and Application

1 General

The industrial truck described in the present operating instructions is designed forlifting, lowering and transporting load units.It must be used, operated and serviced in accordance with the present instructions.Any other type of use is beyond the scope of application and can result in damage topersonnel, the industrial truck or property.

2 Correct application

NOTE

The maximum load and load distance are indicated on the load chart and must not beexceeded.The load must rest on the load handler or be lifted by an attachment approved by themanufacturer.The load must rest on the back of the fork carriage and centrally between the forks.

– Lifting and lowering of loads.– Transporting lowered loads.– Do not carry or lift passengers.– Do push or pull load units.

3 Approved application conditions

– Operation in industrial and commercial environments.– Permissible temperature range -10°C to 40°C.– Operation only on secure, level surfaces with sufficient capacity.– Operation only on routes that are visible and approved by the proprietor.– Inclines of max. 8 % may be negotiated with load, and 16 % without load.– Do not travel across or at an angle on inclines. Travel with the load facing uphill.– Operation in partially public traffic.

Z Special equipment and authorisation are required if the truck is to be used inextreme conditions.The truck is not authorised for use in areas at risk of explosion.

11.1

4 D

E

12

4 Proprietor responsibilities

For the purposes of the present operating instructions the “proprietor” is defined asany natural or legal person who either uses the industrial truck himself, or on whosebehalf it is used. In special cases (e.g. leasing or renting) the proprietor is consideredthe person who, in accordance with existing contractual agreements between theowner and user of the industrial truck, is charged with operational duties.The proprietor must ensure that the industrial truck is used only for the purpose forwhich it is intended and that there is no danger to life and limb of the user and thirdparties. Furthermore, accident prevention regulations, safety regulations andoperating, servicing and repair guidelines must be followed. The proprietor mustensure that all users have read and understood these operating instructions.

NOTE

Failure to comply with the operating instructions shall invalidate the warranty. Thesame applies if improper work is carried out on the truck by the customer or thirdparties without the permission of the manufacturer.

5 Adding attachments and/or accessories

Adding accessories

The mounting or installation of additional equipment which affects or enhances theperformance of the forklift truck requires the written permission of the manufacturer.Local authority approval may also need to be obtained.Local authority approval does not however constitute the manufacturer’s approval.

11.1

4 D

E

12

4 Proprietor responsibilities

For the purposes of the present operating instructions the “proprietor” is defined asany natural or legal person who either uses the industrial truck himself, or on whosebehalf it is used. In special cases (e.g. leasing or renting) the proprietor is consideredthe person who, in accordance with existing contractual agreements between theowner and user of the industrial truck, is charged with operational duties.The proprietor must ensure that the industrial truck is used only for the purpose forwhich it is intended and that there is no danger to life and limb of the user and thirdparties. Furthermore, accident prevention regulations, safety regulations andoperating, servicing and repair guidelines must be followed. The proprietor mustensure that all users have read and understood these operating instructions.

NOTE

Failure to comply with the operating instructions shall invalidate the warranty. Thesame applies if improper work is carried out on the truck by the customer or thirdparties without the permission of the manufacturer.

5 Adding attachments and/or accessories

Adding accessories

The mounting or installation of additional equipment which affects or enhances theperformance of the forklift truck requires the written permission of the manufacturer.Local authority approval may also need to be obtained.Local authority approval does not however constitute the manufacturer’s approval.

13

11.1

4 D

E

B Truck Description

1 Application

The forklift truck is a tiller-operated electric pallet truck with either a fixed or a foldingoperator platform. It is designed for transporting goods on level surfaces. Openbottom pallets or pallets with transverse boards (provided that the boards are outsidethe perimeter of the load wheels) can be lifted.The rated capacity of the truck is shown on the data plate or capacity plate Qmax.

13

11.1

4 D

E

B Truck Description

1 Application

The forklift truck is a tiller-operated electric pallet truck with either a fixed or a foldingoperator platform. It is designed for transporting goods on level surfaces. Openbottom pallets or pallets with transverse boards (provided that the boards are outsidethe perimeter of the load wheels) can be lifted.The rated capacity of the truck is shown on the data plate or capacity plate Qmax.

11.1

4 D

E

14

2 Assemblies and Functional Description

2.1 Assembly Overview

Item Component Item Component

1 t Travel switch 7 t Folding side restraint

2 t Tiller 8 o Folding operator platform

3 t Charge indicator 9 o Tiller height adjuster

4 o CanCode 10 t Fixed operator platform

o CanDis 11 t Caster wheel

o ISM 12 o Skirt

5 t Key switch 13 t Drive wheel

6 t Emergency Disconnect (main switch)

t = Standard version o = Option

7

9

10

13

8

1 2

11

6

3,4,5

12

11.1

4 D

E

14

2 Assemblies and Functional Description

2.1 Assembly Overview

Item Component Item Component

1 t Travel switch 7 t Folding side restraint

2 t Tiller 8 o Folding operator platform

3 t Charge indicator 9 o Tiller height adjuster

4 o CanCode 10 t Fixed operator platform

o CanDis 11 t Caster wheel

o ISM 12 o Skirt

5 t Key switch 13 t Drive wheel

6 t Emergency Disconnect (main switch)

t = Standard version o = Option

7

9

10

13

8

1 2

11

6

3,4,5

12

15

11.1

4 D

E2.2 Functional Description

Safety Mechanisms

– An enclosed, smooth truck geometry with rounded edges ensures safe handling ofthe truck.

– The wheels are surrounded by a solid skirt. – Pressing the Emergency Disconnect switch rapidly cuts out all electrical functions

in hazardous situations.

Hydraulic system

– Lifting and lowering are activated via the lift and lower buttons.– When lifting is activated, the pump unit starts to operate, supplying hydraulic oil

from the oil reservoir to the lift cylinder.

Emergency Stop safety feature

– The emergency stop is activated by the traction controller. – The steering controller sends a system status signal which is monitored by the

traction controller. If the signal fails to appear or a fault is identified the truckautomatically brakes to a halt. Control displays on the driver’s display indicate theemergency stop.

– Each time the truck is switched on the system performed an automatic diagnosis.

Operator position

– All travel and lift operations can be performed sensitively without having to reach.– Tiller for secure control of the industrial truck.– The truck can either be equipped with a fixed or folding operator platform and

moving side arms.

Operator platform

– Travel functions are only released when the driver stands on the operator platform.

Drive system

– A fixed AC threephase motor actuates the drive wheel via a bevel spur gearbox.– The electronic traction controller ensures smooth drive motor speed control and

hence smooth travel, powerful acceleration and electrically controlled braking withenergy regeneration.

– The driver can choose from 3 travel programs, depending on the load and theenvironment. from maximum performance to energy saving.

Steering

– The driver steers with a tiller.– The steering motion is transmitted directly from the steering controller via a steer

motor directly to the ring gear of the pivoted drive system. – The progressive electric steering allows for a 90° turn of the drive wheel when the

tiller is turned only 70°.

15

11.1

4 D

E

2.2 Functional Description

Safety Mechanisms

– An enclosed, smooth truck geometry with rounded edges ensures safe handling ofthe truck.

– The wheels are surrounded by a solid skirt. – Pressing the Emergency Disconnect switch rapidly cuts out all electrical functions

in hazardous situations.

Hydraulic system

– Lifting and lowering are activated via the lift and lower buttons.– When lifting is activated, the pump unit starts to operate, supplying hydraulic oil

from the oil reservoir to the lift cylinder.

Emergency Stop safety feature

– The emergency stop is activated by the traction controller. – The steering controller sends a system status signal which is monitored by the

traction controller. If the signal fails to appear or a fault is identified the truckautomatically brakes to a halt. Control displays on the driver’s display indicate theemergency stop.

– Each time the truck is switched on the system performed an automatic diagnosis.

Operator position

– All travel and lift operations can be performed sensitively without having to reach.– Tiller for secure control of the industrial truck.– The truck can either be equipped with a fixed or folding operator platform and

moving side arms.

Operator platform

– Travel functions are only released when the driver stands on the operator platform.

Drive system

– A fixed AC threephase motor actuates the drive wheel via a bevel spur gearbox.– The electronic traction controller ensures smooth drive motor speed control and

hence smooth travel, powerful acceleration and electrically controlled braking withenergy regeneration.

– The driver can choose from 3 travel programs, depending on the load and theenvironment. from maximum performance to energy saving.

Steering

– The driver steers with a tiller.– The steering motion is transmitted directly from the steering controller via a steer

motor directly to the ring gear of the pivoted drive system. – The progressive electric steering allows for a 90° turn of the drive wheel when the

tiller is turned only 70°.

11.1

4 D

E

16

Electric Steering

– The electric steering system is self-monitoring.The steering controller permanently monitors the entire steering system. If an erroris detected the traction controller interrupts travel, brakes regeneratively and themagnetic brake is applied.

Electrical System

– 24 volt system. – Standard electronic traction, lift and steering control are standard.

Controls and Displays

– Ergonomic controls ensure fatigue-free operation for sensitive application of thetravel operations.

– The battery discharge indicator shows the available battery capacity.– The optional CanDis displays show the key driver information and travel program,

service hours, battery capacity and event messages.

11.1

4 D

E

16

Electric Steering

– The electric steering system is self-monitoring.The steering controller permanently monitors the entire steering system. If an erroris detected the traction controller interrupts travel, brakes regeneratively and themagnetic brake is applied.

Electrical System

– 24 volt system. – Standard electronic traction, lift and steering control are standard.

Controls and Displays

– Ergonomic controls ensure fatigue-free operation for sensitive application of thetravel operations.

– The battery discharge indicator shows the available battery capacity.– The optional CanDis displays show the key driver information and travel program,

service hours, battery capacity and event messages.

17

11.1

4 D

E3 Technical Specifications

Z Technical specification details in accordance with VDI 2198. Technicalmodifications and additions reserved.

3.1 Performance data

ERE 225

Q Rated capacity 2500 kg

c Load centre distance with standard fork length 600 mm

Travel speed w / w.o. rated load 9.5 / 12.5 km/h

Lift speed with / without rated load 0.05 / 0.06 m/s

Lowering speed with / without load 0.055 / 0.04 m/s

Max. gradeability (5 min) w / w.o. load 8.0 / 16.0 %

17

11.1

4 D

E

3 Technical Specifications

Z Technical specification details in accordance with VDI 2198. Technicalmodifications and additions reserved.

3.1 Performance data

ERE 225

Q Rated capacity 2500 kg

c Load centre distance with standard fork length 600 mm

Travel speed w / w.o. rated load 9.5 / 12.5 km/h

Lift speed with / without rated load 0.05 / 0.06 m/s

Lowering speed with / without load 0.055 / 0.04 m/s

Max. gradeability (5 min) w / w.o. load 8.0 / 16.0 %

11.1

4 D

E

18

3.2 Dimensions

1) Depending on the truck design and the load frame, see table for respective specifications

2) Dimensions with top battery removal Dimensions with side battery removal: +72.5 mm

ERE 225

h13 Lowered fork height 85 mm

h14 Truck with fixed operator platform min / max

1254 / 1314mm

Truck with folding operator platform min / max

1158 / 1414mm

h3 Rated lift 122 mm

l2 For truck with fixed operator platform1) 1243 mm

For truck with fixed operator platform1) 834 mm

b1 Truck width 770 mm

y Wheelbase 2) 1482 mm

m2 Ground clearance centre wheelbase 30 mm

b5 Outside straddle 510/540/670 mm

e Fork width 172 mm

s Fork thickness 55 mm

a Safety distance 200 mm

Net weight: See truck data plate

11.1

4 D

E

18

3.2 Dimensions

1) Depending on the truck design and the load frame, see table for respective specifications


ERE 225

h13 Lowered fork height 85 mm

h14 Truck with fixed operator platform min / max

1254 / 1314mm

Truck with folding operator platform min / max

1158 / 1414mm

h3 Rated lift 122 mm

l2 For truck with fixed operator platform1) 1243 mm

For truck with fixed operator platform1) 834 mm

b1 Truck width 770 mm

y Wheelbase 2) 1482 mm

m2 Ground clearance centre wheelbase 30 mm

b5 Outside straddle 510/540/670 mm

e Fork width 172 mm

s Fork thickness 55 mm

a Safety distance 200 mm

Net weight: See truck data plate

19

11.1

4 D

E

3.2.1 Specification sheet for industrial truck with fixed standing platform

19

11.1

4 D

E

3.2.1 Specification sheet for industrial truck with fixed standing platform

11.1

4 D

E

20

ERE 225 working aisle widths

Headlength I2 = 1,243 mm (fixed operator platform)

(all dimensions in mm)

l1 = l2 + lAst = Wa + l6 - x + a (pallet length, a = 200 mm)

1) Load section raised; if load section lowered: +53 mm


l l12) y 1)2) x 1) l6 Wa

1) 2) Ast2)

1000 2243 1331 761 1000 2004 2443

1150 2393 1481 911 1200 2154 2643

1200 2443 1531 961 1200 2204 2643

1400 2643 1731 1161 1400 2404 2843

1600 2843 1931 1361 1600 2604 3043

1750 2993 1707 1137 1800 2380 3243

1800 3043 1757 1187 1800 2430 3243

1950 3193 1907 1337 2000 2580 3443

2150 3393 2107 1537 2150 2780 3593

2150 3393 1867 1297 2150 2540 3593

2400 3643 2731 2161 2400 3404 3843

2400 3643 2357 1787 2400 3030 3843

2400 3643 2117 1547 2400 2790 3843

11.1

4 D

E

20


Headlength I2 = 1,243 mm (fixed operator platform)





l l12) y 1)2) x 1) l6 Wa

1) 2) Ast2)

1000 2243 1331 761 1000 2004 2443

1150 2393 1481 911 1200 2154 2643

1200 2443 1531 961 1200 2204 2643

1400 2643 1731 1161 1400 2404 2843

1600 2843 1931 1361 1600 2604 3043

1750 2993 1707 1137 1800 2380 3243

1800 3043 1757 1187 1800 2430 3243

1950 3193 1907 1337 2000 2580 3443

2150 3393 2107 1537 2150 2780 3593

2150 3393 1867 1297 2150 2540 3593

2400 3643 2731 2161 2400 3404 3843

2400 3643 2357 1787 2400 3030 3843

2400 3643 2117 1547 2400 2790 3843

21

11.1

4 D

E

3.2.2 Dimensions sheet for industrial truck with folding standing platform

21

11.1

4 D

E

3.2.2 Dimensions sheet for industrial truck with folding standing platform

11.1

4 D

E

22


Headlength I2 = 834 mm 2) (folding operator platform)





3) Dimensions for rider mode: +384 mm

l l12) y 1)2) x 1) l6 Wa

1)2)3) Ast2)3)

1000 1834 1331 761 1000 1595 2034

1150 1984 1481 911 1200 1745 2234

1200 2034 1531 961 1200 1795 2234

1400 2234 1731 1161 1400 1995 2434

1600 2434 1931 1361 1600 2195 2634

1750 2584 1707 1137 1800 1971 2834

1800 2634 1757 1187 1800 2021 2834

1950 2784 1907 1337 2000 2171 2034

2150 2984 2107 1537 2150 2371 3184

2150 2984 1867 1297 2150 2131 3184

2400 2334 2731 2161 2400 2995 3434

2400 3234 2357 1787 2400 2621 3434

2400 3234 2117 1547 2400 2381 3434

11.1

4 D

E

22


Headlength I2 = 834 mm 2) (folding operator platform)





3) Dimensions for rider mode: +384 mm

l l12) y 1)2) x 1) l6 Wa

1)2)3) Ast2)3)

1000 1834 1331 761 1000 1595 2034

1150 1984 1481 911 1200 1745 2234

1200 2034 1531 961 1200 1795 2234

1400 2234 1731 1161 1400 1995 2434

1600 2434 1931 1361 1600 2195 2634

1750 2584 1707 1137 1800 1971 2834

1800 2634 1757 1187 1800 2021 2834

1950 2784 1907 1337 2000 2171 2034

2150 2984 2107 1537 2150 2371 3184

2150 2984 1867 1297 2150 2131 3184

2400 2334 2731 2161 2400 2995 3434

2400 3234 2357 1787 2400 2621 3434

2400 3234 2117 1547 2400 2381 3434

23

11.1

4 D

E

3.3 Weights

3.4 Tyre type

ERE 225 (fixed operator

platform)

ERE 225 (folding operator

platform)

Net weight excl. battery 562 503 kg

Axle load, w. loadfront/rear + battery

2150 / 1200 2104 / 1187 kg

Axle load, w.o. loadfront/rear + battery

160 / 690 159 / 632 kg

Battery weight (see "Battery types" on page 35) kg

ERE 220 (fixed standing platform)

ERE 225 (folding standing platform)

Tyre size, drive 230 / 77 230 / 77

Tyre size, load section 85 / 110 85 / 110

Castor wheel (twin wheel) 140 X 57 140 X 57

Wheels, number front/rear(x = driven)

1x +2 /2 1x +2 /2

23

11.1

4 D

E

3.3 Weights

3.4 Tyre type

ERE 225 (fixed operator

platform)

ERE 225 (folding operator

platform)

Net weight excl. battery 562 503 kg

Axle load, w. loadfront/rear + battery

2150 / 1200 2104 / 1187 kg

Axle load, w.o. loadfront/rear + battery

160 / 690 159 / 632 kg

Battery weight (see "Battery types" on page 35) kg

ERE 220 (fixed standing platform)

ERE 225 (folding standing platform)

Tyre size, drive 230 / 77 230 / 77

Tyre size, load section 85 / 110 85 / 110

Castor wheel (twin wheel) 140 X 57 140 X 57

Wheels, number front/rear(x = driven)

1x +2 /2 1x +2 /2

11.1

4 D

E

24

3.5 EN norms

Noise emission level

– ERE 225: 66 dB(A)

in accordance with EN 12053 as harmonised with ISO 4871.

Z The noise emission level is calculated in accordance with standard procedures andtakes into account the noise level when travelling, lifting and when idle. The noiselevel is measured at the level of the driver's ear.

Vibration

– ERE 225: 0,81 m/s²

in accordance with EN 13059

Z The vibration acceleration acting on the body in the operating position is, inaccordance with standard procedures, the linearly integrated, weightedacceleration in the vertical direction. It is calculated when travelling over bumps atconstant speed. These recordings were taken on a single occasion and must notbe confused with the human vibrations of the "2002/44/EC/Vibrations" operatordirective. The manufacturer offers a special service to measure these humanvibrations, (see "Human vibration measurement" on page 117).

Electromagnetic compatibility (EMC)

The manufacturer confirms that the truck adheres to the limits for electromagneticemissions and resistance as well as the static electricity discharge test in accordancewith EN 12895 as well as the standardised instructions contained therein.

Z No changes to electric or electronic components or their arrangement may bemade without the written agreement of the manufacturer.

3.6 Conditions of use

Ambient temperature

– operating at -10°C to 40°C

Z Special equipment and authorisation are required if the truck is to be constantlyused in conditions of extreme temperature or air humidity fluctuations.

Z Special equipment and authorisation are required if the truck is to be used inextreme conditions (e.g. cold stores).The truck is not authorised for use in areas at risk of explosion.

3.7 Electrical requirements

The manufacturer certifies compliance with the requirements for the design andmanufacture of electrical equipment, according to EN 1175 "Industrial Truck Safety -Electrical Requirements", provided the truck is used according to its purpose.

11.1

4 D

E

24

3.5 EN norms

Noise emission level

– ERE 225: 66 dB(A)

in accordance with EN 12053 as harmonised with ISO 4871.

Z The noise emission level is calculated in accordance with standard procedures andtakes into account the noise level when travelling, lifting and when idle. The noiselevel is measured at the level of the driver's ear.

Vibration

– ERE 225: 0,81 m/s²

in accordance with EN 13059

Z The vibration acceleration acting on the body in the operating position is, inaccordance with standard procedures, the linearly integrated, weightedacceleration in the vertical direction. It is calculated when travelling over bumps atconstant speed. These recordings were taken on a single occasion and must notbe confused with the human vibrations of the "2002/44/EC/Vibrations" operatordirective. The manufacturer offers a special service to measure these humanvibrations, (see "Human vibration measurement" on page 117).

Electromagnetic compatibility (EMC)

The manufacturer confirms that the truck adheres to the limits for electromagneticemissions and resistance as well as the static electricity discharge test in accordancewith EN 12895 as well as the standardised instructions contained therein.

Z No changes to electric or electronic components or their arrangement may bemade without the written agreement of the manufacturer.

3.6 Conditions of use

Ambient temperature

– operating at -10°C to 40°C

Z Special equipment and authorisation are required if the truck is to be constantlyused in conditions of extreme temperature or air humidity fluctuations.

Z Special equipment and authorisation are required if the truck is to be used inextreme conditions (e.g. cold stores).The truck is not authorised for use in areas at risk of explosion.

3.7 Electrical requirements

The manufacturer certifies compliance with the requirements for the design andmanufacture of electrical equipment, according to EN 1175 "Industrial Truck Safety -Electrical Requirements", provided the truck is used according to its purpose.

25

11.1

4 D

E3.8 Identification points and data plates

Item Component14 Serial number15 Strap points for crane lifting16 Capacity Qmax17 Battery data plate18 Model name19 Test plaque20 Data plate

Qmax XXX kg

20

15

18

19

16

17

14

25

11.1

4 D

E

3.8 Identification points and data plates

Item Component14 Serial number15 Strap points for crane lifting16 Capacity Qmax17 Battery data plate18 Model name19 Test plaque20 Data plate

Qmax XXX kg

20

15

18

19

16

17

14

11.1

4 D

E

26

Item Component14 Serial number15 Strap points for crane lifting16 Capacity Qmax17 Battery data plate19 Test plaque20 Data plate

Qmax XXX kg

20

15

14

19

16

17

11.1

4 D

E

26

Item Component14 Serial number15 Strap points for crane lifting16 Capacity Qmax17 Battery data plate19 Test plaque20 Data plate

Qmax XXX kg

20

15

14

19

16

17

27

11.1

4 D

E3.8.1 Data plate

Z For queries regarding the truck or ordering spare parts always quote the truck serialnumber (22).

3.8.2 Truck load chart

The load chart (16) gives the capacity (Q) of the truck in kg assuming the load on theload handler is evenly distributed.

21 22 2423 25

32

28

31

30

29

2726

Item Description Item Description21 Type 27 Year of manufacture22 Serial number 28 Load centre (mm)23 Rated capacity (kg) 29 Output24 Battery voltage (V) 30 Min./max. battery weight (kg)25 Net weight w.o. battery (kg) 31 Manufacturer26 Option 32 Manufacturer’s logo

Qmax XXX kg 16

27

11.1

4 D

E

3.8.1 Data plate

Z For queries regarding the truck or ordering spare parts always quote the truck serialnumber (22).

3.8.2 Truck load chart

The load chart (16) gives the capacity (Q) of the truck in kg assuming the load on theload handler is evenly distributed.

21 22 2423 25

32

28

31

30

29

2726

Item Description Item Description21 Type 27 Year of manufacture22 Serial number 28 Load centre (mm)23 Rated capacity (kg) 29 Output24 Battery voltage (V) 30 Min./max. battery weight (kg)25 Net weight w.o. battery (kg) 31 Manufacturer26 Option 32 Manufacturer’s logo

Qmax XXX kg 16

11.1

4 D

E

28

11.1

4 D

E

28

29

11.1

4 D

E

C Transport and Commissioning

1 Lifting by crane

WARNING!

Improper lifting by crane can result in accidentsThe use of unsuitable lifting gear can cause the truck to crash when being lifted bycrane.Prevent the truck from striking other objects when it is being raised, and avoid anyinvoluntary movements. If necessary secure the truck with guide ropes.The truck should only be handled by people who are trained in using lifting slings

and tools.Wear safety shoes when lifting the truck by crane.Do not stand under a swaying load.Do not walk into or stand in a hazardous area.Always use lifting gear with sufficient capacity (for truck weight see truck data

plate).Always attach the crane slings to the prescribed strap points and prevent them from

slipping.Use the lifting gear only in the prescribed load direction.Crane slings should be fastened in such a way that they do not come into contact

with any attachments when lifting.

Lifting the truck by crane

Requirements– Park the truck securely, (see

"Parking the truck securely" onpage 49).

Tools and Material Required– Lifting gear– Crane lifting gear

Procedure• Secure the lifting slings to the strap

points (15).

The truck can now be lifted by crane.

1515 15

29

11.1

4 D

E

C Transport and Commissioning

1 Lifting by crane

WARNING!

Improper lifting by crane can result in accidentsThe use of unsuitable lifting gear can cause the truck to crash when being lifted bycrane.Prevent the truck from striking other objects when it is being raised, and avoid anyinvoluntary movements. If necessary secure the truck with guide ropes.The truck should only be handled by people who are trained in using lifting slings

and tools.Wear safety shoes when lifting the truck by crane.Do not stand under a swaying load.Do not walk into or stand in a hazardous area.Always use lifting gear with sufficient capacity (for truck weight see truck data

plate).Always attach the crane slings to the prescribed strap points and prevent them from

slipping.Use the lifting gear only in the prescribed load direction.Crane slings should be fastened in such a way that they do not come into contact

with any attachments when lifting.

Lifting the truck by crane

Requirements– Park the truck securely, (see


Tools and Material Required– Lifting gear– Crane lifting gear

Procedure• Secure the lifting slings to the strap

points (15).

The truck can now be lifted by crane.

1515 15

11.1

4 D

E

30

2 Transport

WARNING!

Accidental movement during transportImproper fastening of the truck and mast during transport can result in seriousaccidents.Loading must be carried out by specially trained staff in accordance with

recommendations contained in Guidelines VDI 2700 and VDI 2703. In each casecorrect measurements must be made and appropriate safety measures adopted.

The truck must be securely fastened when transported on a lorry or a trailer.The lorry / trailer must have fastening rings.Use wedges to prevent the truck from moving.Use only tensioning belts or tie-down straps or with sufficient strength.

Securing the truck for transport

Tools and Material Required– Tension belts/tie down straps

Procedure• Move the truck onto the transporting

truck.• Park the truck securely, (see


• Strap the belts (34) around the truckand tension them sufficiently.

The truck can now be transported.

34

11.1

4 D

E

30

2 Transport

WARNING!

Accidental movement during transportImproper fastening of the truck and mast during transport can result in seriousaccidents.Loading must be carried out by specially trained staff in accordance with

recommendations contained in Guidelines VDI 2700 and VDI 2703. In each casecorrect measurements must be made and appropriate safety measures adopted.

The truck must be securely fastened when transported on a lorry or a trailer.The lorry / trailer must have fastening rings.Use wedges to prevent the truck from moving.Use only tensioning belts or tie-down straps or with sufficient strength.

Securing the truck for transport

Tools and Material Required– Tension belts/tie down straps

Procedure• Move the truck onto the transporting

truck.• Park the truck securely, (see


• Strap the belts (34) around the truckand tension them sufficiently.

The truck can now be transported.

34

31

11.1

4 D

E3 Using the Truck for the First Time

CAUTION!

Only operate the truck with battery current. Rectified AC current will damage theelectronic components. Cable connections to the battery (tow leads) must be lessthan 6 m long and have a minimum cross-section of 50 mm².

Procedure• Check the equipment is complete.• If necessary install the battery, (see "Battery removal and installation" on page 38)• Charge the battery, (see "Charging the battery" on page 37).

The truck can now be started, (see "Starting up the truck" on page 47)

NOTE

Cold store trucksTrucks designed for use in cold stores have a cold store hydraulic oil and a

protective frame instead of a mast guard on the mast.If a truck with cold store oil is used outside the cold store, the lowering speeds may

increase.

31

11.1

4 D

E

3 Using the Truck for the First Time

CAUTION!

Only operate the truck with battery current. Rectified AC current will damage theelectronic components. Cable connections to the battery (tow leads) must be lessthan 6 m long and have a minimum cross-section of 50 mm².

Procedure• Check the equipment is complete.• If necessary install the battery, (see "Battery removal and installation" on page 38)• Charge the battery, (see "Charging the battery" on page 37).

The truck can now be started, (see "Starting up the truck" on page 47)

NOTE

Cold store trucksTrucks designed for use in cold stores have a cold store hydraulic oil and a

protective frame instead of a mast guard on the mast.If a truck with cold store oil is used outside the cold store, the lowering speeds may

increase.

11.1

4 D

E

32

11.1

4 D

E

32

33

11.1

4 D

E

D Battery - Servicing, Recharging, Replacement

1 Safety Regulations Governing the Handling of Lead-Acid Batteries

Maintenance personnel

Batteries may only be charged, serviced or replaced by trained personnel. Thisoperator manual and the manufacturer’s instructions concerning batteries andcharging stations must be observed when carrying out the work.

Fire protection

Do not smoke and avoid naked flames when handling batteries. Wherever anindustrial truck is parked for charging there shall be no inflammable material orlubricants capable of creating sparks within 2 m around the truck. The room must beventilated. Fire protection equipment must be on hand.

Battery maintenance

The battery cell covers must be kept dry and clean. The terminals and cable shoesmust be clean, secure and have a light coating of dielectric grease.

CAUTION!

Before closing the battery panel make sure that the battery cable cannot bedamaged. There is a risk of short circuits with damaged cables.

Battery disposal

Batteries may only be disposed of in accordance with national environmentalprotection regulations or disposal laws. The manufacturer’s disposal instructionsmust be followed.

33

11.1

4 D

E

D Battery - Servicing, Recharging, Replacement

1 Safety Regulations Governing the Handling of Lead-Acid Batteries


Batteries may only be charged, serviced or replaced by trained personnel. Thisoperator manual and the manufacturer’s instructions concerning batteries andcharging stations must be observed when carrying out the work.

Fire protection

Do not smoke and avoid naked flames when handling batteries. Wherever anindustrial truck is parked for charging there shall be no inflammable material orlubricants capable of creating sparks within 2 m around the truck. The room must beventilated. Fire protection equipment must be on hand.

Battery maintenance

The battery cell covers must be kept dry and clean. The terminals and cable shoesmust be clean, secure and have a light coating of dielectric grease.

CAUTION!

Before closing the battery panel make sure that the battery cable cannot bedamaged. There is a risk of short circuits with damaged cables.

Battery disposal

Batteries may only be disposed of in accordance with national environmentalprotection regulations or disposal laws. The manufacturer’s disposal instructionsmust be followed.

11.1

4 D

E

34

WARNING!

Batteries can be hazardousBatteries contain an acid solution which is poisonous and corrosive. Avoid contactwith battery acid at all times.Dispose of used battery acid in accordance with regulations.Always wear protective clothing and goggles when working with batteries.Do not let battery acid come into contact with skin, clothing or eyes. If necessary,

rinse with plenty of clean water.In the event of physical damage (e.g. skin or eye contact with battery acid) call for

a doctor immediately.Spilled battery acid should be neutralised immediately with plenty of water.Only batteries with a sealed battery container may be used.Follow national guidelines and legislation.

WARNING!

Unsuitable batteries that have not been approved by Jungheinrich for the truckcan be hazardousThe design, weight and dimensions of the battery have a considerable effect on theoperational safety of the truck, in particular its stability and capacity. The use ofunsuitable batteries that have not been approved by Jungheinrich for the truck canlead to a deterioration of the braking system during energy recovery operations andalso cause considerable damage to the electrical control system. The use of batteriesthat have not been approved by Jungheinrich can therefore affect the health andsafety of personnel.Only manufacturer-approved batteries may be used on the truck.Replacement of the battery equipment requires the manufacturer's agreement.When replacing/installing the battery make sure the battery is securely located in

the battery compartment of the truck.Do not use batteries that have not been approved by the manufacturer.

Park the truck securely before carrying out any work on the batteries ((see "Parkingthe truck securely" on page 49)).

11.1

4 D

E

34

WARNING!

Batteries can be hazardousBatteries contain an acid solution which is poisonous and corrosive. Avoid contactwith battery acid at all times.Dispose of used battery acid in accordance with regulations.Always wear protective clothing and goggles when working with batteries.Do not let battery acid come into contact with skin, clothing or eyes. If necessary,

rinse with plenty of clean water.In the event of physical damage (e.g. skin or eye contact with battery acid) call for

a doctor immediately.Spilled battery acid should be neutralised immediately with plenty of water.Only batteries with a sealed battery container may be used.Follow national guidelines and legislation.

WARNING!

Unsuitable batteries that have not been approved by Jungheinrich for the truckcan be hazardousThe design, weight and dimensions of the battery have a considerable effect on theoperational safety of the truck, in particular its stability and capacity. The use ofunsuitable batteries that have not been approved by Jungheinrich for the truck canlead to a deterioration of the braking system during energy recovery operations andalso cause considerable damage to the electrical control system. The use of batteriesthat have not been approved by Jungheinrich can therefore affect the health andsafety of personnel.Only manufacturer-approved batteries may be used on the truck.Replacement of the battery equipment requires the manufacturer's agreement.When replacing/installing the battery make sure the battery is securely located in

the battery compartment of the truck.Do not use batteries that have not been approved by the manufacturer.

Park the truck securely before carrying out any work on the batteries ((see "Parkingthe truck securely" on page 49)).

35

11.1

4 D

E2 Battery types

Depending on the model, the truck will be supplied with different battery types. Thefollowing table shows which combinations are included as standard:

The battery weights can be taken from the battery data plate. Batteries with noninsulated terminals must be covered with a non slip insulating mat.

Tray type Battery type Capacity Weight

ERE L tray 24 volt battery 624x284x627 mm (Lxwxh)

3 EPzS 375 Ah 302 kg

24 volt battery 624x284x627 mm (Lxwxh)

3 EPzV 300 Ah maintenance-free

302 kg

24 volt battery 624X284X627 mm (LXWXH)

3 PzW 330 Ah - maintenance-free

200

288 kg

ERE L traySide battery removal


3 EPzS 450 Ah HX

302 kg



302 kg



200

288 kg

ERE L tray, high Side battery removal

24 V - Battery 798X212X627 mm (LXWXH)


35

11.1

4 D

E

2 Battery types

Depending on the model, the truck will be supplied with different battery types. Thefollowing table shows which combinations are included as standard:

The battery weights can be taken from the battery data plate. Batteries with noninsulated terminals must be covered with a non slip insulating mat.

Tray type Battery type Capacity Weight

ERE L tray 24 volt battery 624x284x627 mm (Lxwxh)




302 kg



200

288 kg

ERE L traySide battery removal


3 EPzS 450 Ah HX

302 kg



302 kg



200

288 kg

ERE L tray, high Side battery removal

24 V - Battery 798X212X627 mm (LXWXH)


11.1

4 D

E

36

3 Exposing the battery

CAUTION!

Trapping hazardMake sure there is nothing between the battery cover and the truck when you fit the

battery cover.

WARNING!

An unsecured truck can cause accidentsParking the truck on an incline or with a raised load handler is dangerous and isstrictly prohibited.Always park the truck on a level surface. In special cases the truck may need to be

secured with wedges.Always fully lower the mast and forks.Select a place to park where no other people are at risk of injury from lowering

forks.

Requirements– Park the truck on a level surface.– Park the truck securely, (see


Procedure• Depress the Emergency

Disconnect (6).• Pull up the battery panel (35) using

the recess and lift it back (36).

The battery connector and batteryretainer can be accessed

35

6

36

11.1

4 D

E

36

3 Exposing the battery

CAUTION!

Trapping hazardMake sure there is nothing between the battery cover and the truck when you fit the

battery cover.

WARNING!

An unsecured truck can cause accidentsParking the truck on an incline or with a raised load handler is dangerous and isstrictly prohibited.Always park the truck on a level surface. In special cases the truck may need to be

secured with wedges.Always fully lower the mast and forks.Select a place to park where no other people are at risk of injury from lowering

forks.

Requirements– Park the truck on a level surface.– Park the truck securely, (see


Procedure• Depress the Emergency

Disconnect (6).• Pull up the battery panel (35) using

the recess and lift it back (36).

The battery connector and batteryretainer can be accessed

35

6

36

37

11.1

4 D

E4 Charging the battery

WARNING!

The gases produced during charging can cause explosionsThe battery produces a mixture of nitrogen and hydrogen (electrolytic gas) duringcharging. Gassing is a chemical process. This gas mixture is highly explosive andmust not be ignited.Switch the charging station and truck off first before connecting/disconnecting the

charging cable of the battery charging station to/from the battery connector.The charger must be adapted to the battery in terms of voltage and charge

capacity.Before charging, check all cables and plug connections for visible signs of damage.Ventilate the room in which the truck is being charged.The battery cover must be open and the battery cell surfaces must be exposed

during charging to ensure adequate ventilation.Do not smoke and avoid naked flames when handling batteries.Wherever an industrial truck is parked for charging there shall be no inflammable

material or lubricants capable of creating sparks within 2 m around the truck.Fire protection equipment must be on hand.Do not lay any metallic objects on battery.It is essential to follow the safety regulations of the battery and charger station

manufacturers.

Charge the battery

Requirements– Expose the battery, (see "Exposing the

battery" on page 36).

Procedure• Disconnect the battery connector (37)

from the truck connector.• Connect the battery connector (37) to

the charging cable (38) of the stationarycharger.

• Start charging in accordance with thecharger operating instructions.

The battery is now charged.

Completing the battery charge, restoring the truck to operation

NOTE

If charging has been interrupted, the full battery capacity will not be available

Requirements– Battery charging is complete.

37

38

37

11.1

4 D

E

4 Charging the battery

WARNING!

The gases produced during charging can cause explosionsThe battery produces a mixture of nitrogen and hydrogen (electrolytic gas) duringcharging. Gassing is a chemical process. This gas mixture is highly explosive andmust not be ignited.Switch the charging station and truck off first before connecting/disconnecting the

charging cable of the battery charging station to/from the battery connector.The charger must be adapted to the battery in terms of voltage and charge

capacity.Before charging, check all cables and plug connections for visible signs of damage.Ventilate the room in which the truck is being charged.The battery cover must be open and the battery cell surfaces must be exposed

during charging to ensure adequate ventilation.Do not smoke and avoid naked flames when handling batteries.Wherever an industrial truck is parked for charging there shall be no inflammable

material or lubricants capable of creating sparks within 2 m around the truck.Fire protection equipment must be on hand.Do not lay any metallic objects on battery.It is essential to follow the safety regulations of the battery and charger station

manufacturers.

Charge the battery

Requirements– Expose the battery, (see "Exposing the

battery" on page 36).

Procedure• Disconnect the battery connector (37)

from the truck connector.• Connect the battery connector (37) to

the charging cable (38) of the stationarycharger.

• Start charging in accordance with thecharger operating instructions.

The battery is now charged.

Completing the battery charge, restoring the truck to operation

NOTE

If charging has been interrupted, the full battery capacity will not be available

Requirements– Battery charging is complete.

37

38

11.1

4 D

E

38

Procedure• Complete charging in accordance with the charger operating instructions.• Disconnect the battery from the charger.• Connect the battery to the truck.

The truck is operational again

5 Battery removal and installation

WARNING!

Accident risk during battery removal and installationDue to the battery weight and acid there is a risk of trapping or scalding when thebattery is removed and installed.Note the "Safety regulations for handling acid batteries" section in this chapter.Wear safety shoes when removing and installing the battery.Use only batteries with insulated cells and terminal connectors.Park the truck on a level surface to prevent the battery from sliding out.Make sure the crane slings have sufficient capacity to replace the battery.Use only approved battery replacement devices (battery roller stand, replacement

trolley etc.).Make sure the battery is securely located in the truck's battery compartment.

11.1

4 D

E

38

Procedure• Complete charging in accordance with the charger operating instructions.• Disconnect the battery from the charger.• Connect the battery to the truck.

The truck is operational again

5 Battery removal and installation

WARNING!

Accident risk during battery removal and installationDue to the battery weight and acid there is a risk of trapping or scalding when thebattery is removed and installed.Note the "Safety regulations for handling acid batteries" section in this chapter.Wear safety shoes when removing and installing the battery.Use only batteries with insulated cells and terminal connectors.Park the truck on a level surface to prevent the battery from sliding out.Make sure the crane slings have sufficient capacity to replace the battery.Use only approved battery replacement devices (battery roller stand, replacement

trolley etc.).Make sure the battery is securely located in the truck's battery compartment.

39

11.1

4 D

E5.1 Removing the battery from the top

Battery removal

Requirements– Park the truck securely, (see "Parking the truck securely" on page 49).– Expose the battery, (see "Exposing the battery" on page 36).

Procedure• Disconnect the battery connector from the truck connector.

Z Place the battery cable on the tray so that it cannot be severed when the battery ispulled out.

• Undo the screw (40) of the battery retainer and remove the battery retainer (39).• Strap the crane lifting gear to the eyes (41).

Z The crane lifting gear must exert a vertical pull. The hooks of the lifting gear mustnever fall onto the battery cells.

• Pull the battery up out of the battery compartment.

The battery is now removed.

Z Installation is in the reverse order. When reinstalling the battery, note the properinstallation position and make sure the battery is connected correctly.

Z Screw torque (40): 45 Nm

40 39 41

39

11.1

4 D

E

5.1 Removing the battery from the top

Battery removal

Requirements– Park the truck securely, (see "Parking the truck securely" on page 49).– Expose the battery, (see "Exposing the battery" on page 36).

Procedure• Disconnect the battery connector from the truck connector.

Z Place the battery cable on the tray so that it cannot be severed when the battery ispulled out.

• Undo the screw (40) of the battery retainer and remove the battery retainer (39).• Strap the crane lifting gear to the eyes (41).

Z The crane lifting gear must exert a vertical pull. The hooks of the lifting gear mustnever fall onto the battery cells.

• Pull the battery up out of the battery compartment.


Z Installation is in the reverse order. When reinstalling the battery, note the properinstallation position and make sure the battery is connected correctly.

Z Screw torque (40): 45 Nm

40 39 41

11.1

4 D

E

40

5.2 Removing the battery from the side

CAUTION!

Trapping hazardTrapping hazard when removing and installing the battery.When removing and installing the battery do not put your hands between the

battery and the chassis.

Battery removal

Requirements– Park the truck securely, (see "Parking the truck

securely" on page 49).– Expose the battery, (see "Exposing the battery"

on page 36).

Tools and Material Required– Battery replacement station / trolley

Procedure• Disconnect the battery connector (37) from the

truck connector.• Undo the battery lock (42).• Move the battery replacement station / trolley up

to the side of the truck.• Turn the battery lock as far as the stop.• Carefully push the battery from off the truck onto the battery replacement station /

trolley.


Battery installation



on page 36).

ProcedureZ Installation is in the reverse order. When

reinstalling the battery, note the properinstallation position and make sure the battery isconnected correctly.

42

42

11.1

4 D

E

40

5.2 Removing the battery from the side

CAUTION!

Trapping hazardTrapping hazard when removing and installing the battery.When removing and installing the battery do not put your hands between the

battery and the chassis.

Battery removal



on page 36).

Tools and Material Required– Battery replacement station / trolley

Procedure• Disconnect the battery connector (37) from the

truck connector.• Undo the battery lock (42).• Move the battery replacement station / trolley up

to the side of the truck.• Turn the battery lock as far as the stop.• Carefully push the battery from off the truck onto the battery replacement station /

trolley.


Battery installation



on page 36).

ProcedureZ Installation is in the reverse order. When

reinstalling the battery, note the properinstallation position and make sure the battery isconnected correctly.

42

42

41

11.1

4 D

EE Operation

1 Safety Regulations for the Operation of theForklift Truck

Driver authorisation

The truck may only be used by suitably trained personnel, who have demonstrated tothe proprietor or his representative that they can drive and handle loads and havebeen authorised to operate the truck by the proprietor or his representative.

Driver’s rights, obligations and responsibilities

The driver must be informed of his duties and responsibilities and be instructed in theoperation of the truck and shall be familiar with the operating instructions. The drivershall be afforded all due rights. Safety shoes must be worn for pedestrian operatedtrucks.

Unauthorised use of truck

The driver is responsible for the truck during the time it is in use. The driver mustprevent unauthorised persons from driving or operating the truck. Do not carrypassengers or lift other people.

Damage and faults

The supervisor must be immediately informed of any damage or faults to the truck orattachment. Trucks which are unsafe for operation (e.g. wheel or brake problems)must not be used until they have been rectified.

Repairs

The driver must not carry out any repairs or alterations to the truck without thenecessary training and authorisation to do so. The driver must never disable or adjustsafety mechanisms or switches.

Hazardous area

WARNING!

Risk of accidents / injury in the hazardous area of the truckThe hazardous area is defined as the area in which a person is at risk due to truckmovement, lifting operations, the load handler (e.g. forks or attachments) or the loaditself. This also includes areas which can be reached by falling loads or loweringoperating equipment.Instruct unauthorised people to leave the hazardous area.Give a warning signal with plenty of time for people to leave.If unauthorised personnel are still within the hazardous area stop the truck

immediately.

41

11.1

4 D

E

E Operation

1 Safety Regulations for the Operation of theForklift Truck

Driver authorisation

The truck may only be used by suitably trained personnel, who have demonstrated tothe proprietor or his representative that they can drive and handle loads and havebeen authorised to operate the truck by the proprietor or his representative.

Driver’s rights, obligations and responsibilities

The driver must be informed of his duties and responsibilities and be instructed in theoperation of the truck and shall be familiar with the operating instructions. The drivershall be afforded all due rights. Safety shoes must be worn for pedestrian operatedtrucks.

Unauthorised use of truck

The driver is responsible for the truck during the time it is in use. The driver mustprevent unauthorised persons from driving or operating the truck. Do not carrypassengers or lift other people.

Damage and faults

The supervisor must be immediately informed of any damage or faults to the truck orattachment. Trucks which are unsafe for operation (e.g. wheel or brake problems)must not be used until they have been rectified.

Repairs

The driver must not carry out any repairs or alterations to the truck without thenecessary training and authorisation to do so. The driver must never disable or adjustsafety mechanisms or switches.

Hazardous area

WARNING!

Risk of accidents / injury in the hazardous area of the truckThe hazardous area is defined as the area in which a person is at risk due to truckmovement, lifting operations, the load handler (e.g. forks or attachments) or the loaditself. This also includes areas which can be reached by falling loads or loweringoperating equipment.Instruct unauthorised people to leave the hazardous area.Give a warning signal with plenty of time for people to leave.If unauthorised personnel are still within the hazardous area stop the truck

immediately.

11.1

4 D

E

42

Safety devices and warning labels

Safety devices, warning signs ((see "Identification points and data plates" onpage 25)) and warning instructions in the present operating instructions must bestrictly observed.

11.1

4 D

E

42

Safety devices and warning labels

Safety devices, warning signs ((see "Identification points and data plates" onpage 25)) and warning instructions in the present operating instructions must bestrictly observed.

43

11.1

4 D

E2 Displays and Controls

476

48

45

44

546

1

4546

4, 50, 51, 3

8

7

49

43

2

43

11.1

4 D

E

2 Displays and Controls

476

48

45

44

546

1

4546

4, 50, 51, 3

8

7

49

43

2

11.1

4 D

E

44

Item Control / Display Function1 Travel switch t – Controls the travel direction and speed.2 Tiller (“fixed operator

platform” version)t – Steers the truck.

Tiller (“fixed operator platform” version, height-adjustable, except for L tray high)

o – Steers the truck.

Moving tiller (“folding operator platform” version)

t – Steers the truck.– Decelerates the truck,(see "Brakes" on

page 56).3 Charge display t – Battery charge status4 CanCode o Replaces the key switch

– Entering the code activates the truck– Travel program selection– Code setting– Parameter setting

5 Key switch t – Activates the truck by applying the control voltage

– Removing the key prevents the truck from being switched on by unauthorised personnel

6 Emergency Disconnect switch

t Disconnects the battery supply– All electric functions are deactivated and

the truck decelerates7 Folding side arm (“folding

operator platform” version)

t When the side restraints are not unfolded and the operator platform is laden and unfolded:

– travel speed restricted to max. 6km/h.

8 Folding operator platform t Pedestrian mode– Operator platform folded up:

Pedestrian speed restricted to max. 4.0 km/h.

Rider mode, operator platform acts as a deadman:– Operator platform down and vacated:

travel inhibited.– Operator platform down and laden by

weight of operator (both restraints must be folded fully out or in):travel enabled.

43 Rigid side arm (“fixed operator platform” version)

t – Rider mode only available.

11.1

4 D

E

44

Item Control / Display Function1 Travel switch t – Controls the travel direction and speed.2 Tiller (“fixed operator

platform” version)t – Steers the truck.

Tiller (“fixed operator platform” version, height-adjustable, except for L tray high)

o – Steers the truck.

Moving tiller (“folding operator platform” version)

t – Steers the truck.– Decelerates the truck,(see "Brakes" on

page 56).3 Charge display t – Battery charge status4 CanCode o Replaces the key switch

– Entering the code activates the truck– Travel program selection– Code setting– Parameter setting

5 Key switch t – Activates the truck by applying the control voltage

– Removing the key prevents the truck from being switched on by unauthorised personnel

6 Emergency Disconnect switch

t Disconnects the battery supply– All electric functions are deactivated and

the truck decelerates7 Folding side arm (“folding

operator platform” version)

t When the side restraints are not unfolded and the operator platform is laden and unfolded:

– travel speed restricted to max. 6km/h.

8 Folding operator platform t Pedestrian mode– Operator platform folded up:

Pedestrian speed restricted to max. 4.0 km/h.

Rider mode, operator platform acts as a deadman:– Operator platform down and vacated:

travel inhibited.– Operator platform down and laden by

weight of operator (both restraints must be folded fully out or in):travel enabled.

43 Rigid side arm (“fixed operator platform” version)

t – Rider mode only available.

45

11.1

4 D

E

44 Collision safety switch t Safety function– (“Fixed operator platform” version):

The truck brakes.Safety feature on the folding operator platform– Pedestrian mode:

When pressed the truck travels for approx. 3 seconds in the forks direction. The parking brake then applies. The truck remains switched off until the travel switch is set to neutral.

– Rider mode:No function (optional safety collision switch function as in pedestrian mode)

45 “Lower” button t – Lowers the lift mechanism.46 “Lift” button t – Raises the lift mechanism.47 Warning signal (horn)

buttont – “Warning” button

48 Fixed platform (all functions released when occupied)

t Rider mode only, pressure-sensitive mat acts as deadman switch:

– Pressure-sensitive mat laden:Travel and all functions enabled.

– Pressure-sensitive mat unladen:The truck coasts.

49 Side skirt t – Driver protection50 CanDis o Display instrument

– Battery charge status– Operating hours– Warning messages– Parameter settings

51 ISM o Replaces the key switch– Activates the truck via a card /

transponder– Displays readiness for operation– Operational data acquisition– Data exchange with card / transponder

t = Standard equipment o = Optional equipment

Item Control / Display Function

45

11.1

4 D

E

44 Collision safety switch t Safety function– (“Fixed operator platform” version):

The truck brakes.Safety feature on the folding operator platform– Pedestrian mode:

When pressed the truck travels for approx. 3 seconds in the forks direction. The parking brake then applies. The truck remains switched off until the travel switch is set to neutral.

– Rider mode:No function (optional safety collision switch function as in pedestrian mode)

45 “Lower” button t – Lowers the lift mechanism.46 “Lift” button t – Raises the lift mechanism.47 Warning signal (horn)

buttont – “Warning” button

48 Fixed platform (all functions released when occupied)

t Rider mode only, pressure-sensitive mat acts as deadman switch:

– Pressure-sensitive mat laden:Travel and all functions enabled.

– Pressure-sensitive mat unladen:The truck coasts.

49 Side skirt t – Driver protection50 CanDis o Display instrument

– Battery charge status– Operating hours– Warning messages– Parameter settings

51 ISM o Replaces the key switch– Activates the truck via a card /

transponder– Displays readiness for operation– Operational data acquisition– Data exchange with card / transponder

t = Standard equipment o = Optional equipment

Item Control / Display Function

11.1

4 D

E

46

2.1 Battery discharge indicator

When the truck has been released via the keyswitch, code lock or ISM, the battery charge statusis displayed. The LED (52) colours represent thefollowing conditions:

Z If the LED is red, load units can no longer be lifted. Lifting is only enabled againwhen the battery connected is at least 70% charged.

If the LED flashes red and the truck is not ready for operation, inform themanufacturer's service department. Red flashing is a truck controller code. Theflashing sequence indicates the type of fault.

LED colour Residual capacityGreen 40 - 100 %

Orange 30 - 40 %Flashing

green/orange 1Hz20 - 30 %

Red 0 - 20 %

52

11.1

4 D

E

46

2.1 Battery discharge indicator

When the truck has been released via the keyswitch, code lock or ISM, the battery charge statusis displayed. The LED (52) colours represent thefollowing conditions:

Z If the LED is red, load units can no longer be lifted. Lifting is only enabled againwhen the battery connected is at least 70% charged.

If the LED flashes red and the truck is not ready for operation, inform themanufacturer's service department. Red flashing is a truck controller code. Theflashing sequence indicates the type of fault.

LED colour Residual capacityGreen 40 - 100 %

Orange 30 - 40 %Flashing

green/orange 1Hz20 - 30 %

Red 0 - 20 %

52

47

11.1

4 D

E3 Starting up the truck

3.1 Checks and operations to be performed before starting daily operation

WARNING!

Damage and other truck or attachment (special equipment) defects can resultin accidents.If damage or other truck or attachment (special equipment) defects are discoveredduring the following checks, the truck must be taken out of service until it has beenrepaired.Report any defects immediately to your supervisor.Tag out and decommission a faulty lift truck.Only return the truck to service when you have identified and rectified the fault.

Pre-start inspections

Procedure• Check the whole of the outside of the truck for signs of damage and leaks.

Damaged hoses must be replaced immediately.• Check the battery attachment and wire connections for damage and make sure

they are secure.• Check the battery connectors are secure.• Check the load handler for visible signs of damage such as cracks, bent or severely

worn forks.• Check the drive wheel and load wheels for damage.• Check that the markings and labels are present, clean and legible, (see

"Identification points and data plates" on page 25).• Test the Emergency Disconnect switch.• Check the control handle (damper) is restored to its normal position.• Check the controls are automatically restored to zero after being applied.• Test the warning signal.• Test the brakes.• Test the collision safety switch.

47

11.1

4 D

E

3 Starting up the truck

3.1 Checks and operations to be performed before starting daily operation

WARNING!

Damage and other truck or attachment (special equipment) defects can resultin accidents.If damage or other truck or attachment (special equipment) defects are discoveredduring the following checks, the truck must be taken out of service until it has beenrepaired.Report any defects immediately to your supervisor.Tag out and decommission a faulty lift truck.Only return the truck to service when you have identified and rectified the fault.

Pre-start inspections

Procedure• Check the whole of the outside of the truck for signs of damage and leaks.

Damaged hoses must be replaced immediately.• Check the battery attachment and wire connections for damage and make sure

they are secure.• Check the battery connectors are secure.• Check the load handler for visible signs of damage such as cracks, bent or severely

worn forks.• Check the drive wheel and load wheels for damage.• Check that the markings and labels are present, clean and legible, (see

"Identification points and data plates" on page 25).• Test the Emergency Disconnect switch.• Check the control handle (damper) is restored to its normal position.• Check the controls are automatically restored to zero after being applied.• Test the warning signal.• Test the brakes.• Test the collision safety switch.

11.1

4 D

E

48

3.2 Preparing the truck for operation

Switching on the truck

Requirements– For checks and operations to be performed before starting daily operation, (see

"Checks and operations to be performed before starting daily operation" onpage 47).

Procedure• Step onto the standing platform (48, 8).• Pull out the Emergency Disconnect switch (6).• Switch on the truck, to do this:

• Insert the key in the key switch (53) and turn it to the right as far as it will go(position “I”) or for CANCODE (4,o) enter the activation code, (see "CanCodekeypad" on page 65).

• Test the warning signal button (47).• Test the travel switch (1).• Test the steering.

The truck is operational.

WARNING!

Do not press the travel switch or the "pedestrian" button (o) when entering andexiting the truck.

Z The CANDID display instrument (50(o)) indicates the available battery capacity.

44 47 53 6

4, 50

11.1

4 D

E

48

3.2 Preparing the truck for operation

Switching on the truck

Requirements– For checks and operations to be performed before starting daily operation, (see

"Checks and operations to be performed before starting daily operation" onpage 47).

Procedure• Step onto the standing platform (48, 8).• Pull out the Emergency Disconnect switch (6).• Switch on the truck, to do this:

• Insert the key in the key switch (53) and turn it to the right as far as it will go(position “I”) or for CANCODE (4,o) enter the activation code, (see "CanCodekeypad" on page 65).

• Test the warning signal button (47).• Test the travel switch (1).• Test the steering.

The truck is operational.

WARNING!

Do not press the travel switch or the "pedestrian" button (o) when entering andexiting the truck.

Z The CANDID display instrument (50(o)) indicates the available battery capacity.

44 47 53 6

4, 50

49

11.1

4 D

E3.3 Parking the truck securely

WARNING!

An unsecured truck can cause accidentsParking the truck on an incline, without the brakes applied or with a raised load / loadhandler is dangerous and is strictly prohibited.Always park the truck on a level surface. In special cases the truck may need to be

secured with wedges.Always lower the forks fully.Select a place to park where no other people are at risk of injury from lowering

forks.

Parking the truck securely

Procedure• Fully lower the load handler.• Set the drive wheel to “Straight ahead”.

Z Set tiller to the "Forward position".• Turn off the key switch and remove the key.• For CANCODE, press the O key.• For ISM, press the red button.• Press the Emergency Disconnect.

The truck is parked.

3.4 Battery discharge monitor

Z The standard setting for the battery discharge indicator / discharge monitor isbased on standard batteries. When using maintenance-free or special batteries thedisplay and cutout points of the battery discharge monitor must be set byauthorised specialist personnel. If this adjustment is not made the battery maybecome damaged through excessive depletion.

If the residual capacity falls below the required level, lifting is inhibited. An alternatingdisplay (52) appears. Lifting is only released when the battery connected is at least70% charged.

49

11.1

4 D

E

3.3 Parking the truck securely

WARNING!

An unsecured truck can cause accidentsParking the truck on an incline, without the brakes applied or with a raised load / loadhandler is dangerous and is strictly prohibited.Always park the truck on a level surface. In special cases the truck may need to be

secured with wedges.Always lower the forks fully.Select a place to park where no other people are at risk of injury from lowering

forks.

Parking the truck securely

Procedure• Fully lower the load handler.• Set the drive wheel to “Straight ahead”.

Z Set tiller to the "Forward position".• Turn off the key switch and remove the key.• For CANCODE, press the O key.• For ISM, press the red button.• Press the Emergency Disconnect.

The truck is parked.

3.4 Battery discharge monitor

Z The standard setting for the battery discharge indicator / discharge monitor isbased on standard batteries. When using maintenance-free or special batteries thedisplay and cutout points of the battery discharge monitor must be set byauthorised specialist personnel. If this adjustment is not made the battery maybecome damaged through excessive depletion.

If the residual capacity falls below the required level, lifting is inhibited. An alternatingdisplay (52) appears. Lifting is only released when the battery connected is at least70% charged.

11.1

4 D

E

50

4 Industrial Truck Operation

4.1 Safety regulations for truck operation

Travel routes and work areas

Only use lanes and routes specifically designated for truck traffic. Unauthorised thirdparties must stay away from work areas. Loads must only be stored in placesspecially designated for this purpose.The truck must only be operated in work areas with sufficient lighting to avoid dangerto personnel and materials. Additional equipment is necessary to operate the truck inareas of insufficient lighting.

DANGER!

Do not exceed the permissible surface and spot load limits on the travel routes.At blind spots get a second person to assist.The driver must ensure that the loading dock / ramp cannot move or come looseduring loading / unloading.

Travel conduct

The driver must adapt the travel speed to local conditions. The truck must be drivenat slow speed when negotiating bends or narrow passageways, when passingthrough swing doors and at blind spots. The driver must always observe an adequatebraking distance between the forklift truck and the vehicle in front and must be incontrol of the truck at all times. Abrupt stopping (except in emergencies), rapid U turnsand overtaking at dangerous or blind spots are not permitted. Do not lean out or reachbeyond the working and operating area.

Travel visibility

The driver must look in the direction of travel and must always have a clear view ofthe route ahead. Loads that affect visibility must be positioned at the rear of the truck.If this is not possible, a second person must walk alongside the truck as a lookout toobserve the travel route while maintaining eye contact with the driver. Proceed onlyat walking pace and with particular care. Stop the truck as soon as you lose eyecontact.

Negotiating slopes and inclines

Negotiating slopes or inclines is only permitted if they are specifically designed astravel routes, are clean and have a non-slip surface and providing they can be safelytravelled along in accordance with the truck's technical specifications. The truck mustalways be driven with the load unit facing uphill. The industrial truck must not beturned, operated at an angle or parked on inclines or slopes. Inclines must only benegotiated at slow speed, with the driver ready to brake at any moment.

11.1

4 D

E

50

4 Industrial Truck Operation

4.1 Safety regulations for truck operation

Travel routes and work areas

Only use lanes and routes specifically designated for truck traffic. Unauthorised thirdparties must stay away from work areas. Loads must only be stored in placesspecially designated for this purpose.The truck must only be operated in work areas with sufficient lighting to avoid dangerto personnel and materials. Additional equipment is necessary to operate the truck inareas of insufficient lighting.

DANGER!

Do not exceed the permissible surface and spot load limits on the travel routes.At blind spots get a second person to assist.The driver must ensure that the loading dock / ramp cannot move or come looseduring loading / unloading.

Travel conduct

The driver must adapt the travel speed to local conditions. The truck must be drivenat slow speed when negotiating bends or narrow passageways, when passingthrough swing doors and at blind spots. The driver must always observe an adequatebraking distance between the forklift truck and the vehicle in front and must be incontrol of the truck at all times. Abrupt stopping (except in emergencies), rapid U turnsand overtaking at dangerous or blind spots are not permitted. Do not lean out or reachbeyond the working and operating area.

Travel visibility

The driver must look in the direction of travel and must always have a clear view ofthe route ahead. Loads that affect visibility must be positioned at the rear of the truck.If this is not possible, a second person must walk alongside the truck as a lookout toobserve the travel route while maintaining eye contact with the driver. Proceed onlyat walking pace and with particular care. Stop the truck as soon as you lose eyecontact.

Negotiating slopes and inclines

Negotiating slopes or inclines is only permitted if they are specifically designed astravel routes, are clean and have a non-slip surface and providing they can be safelytravelled along in accordance with the truck's technical specifications. The truck mustalways be driven with the load unit facing uphill. The industrial truck must not beturned, operated at an angle or parked on inclines or slopes. Inclines must only benegotiated at slow speed, with the driver ready to brake at any moment.

51

11.1

4 D

E

Negotiating lifts and docks

Lifts may only be entered if they have sufficient capacity, are suitable for driving onand authorised for truck traffic by the owner. The driver must satisfy himself of theabove before entering these areas. The truck must enter lifts with the load in front andmust take up a position which does not allow it to come into contact with the walls ofthe lift shaft. People travelling in the lift with the forklift truck must only enter the liftafter the truck has come to a halt and must exit the lift before the truck. The drivermust ensure that the loading ramp / bridge cannot move or come loose during loading/ unloading.

Type of loads to be carried

The operator must make sure that the load is in a satisfactory condition. Loads mustalways be positioned safely and carefully. Use suitable precautions to prevent partsof the load from tipping or falling down.

51

11.1

4 D

E

Negotiating lifts and docks

Lifts may only be entered if they have sufficient capacity, are suitable for driving onand authorised for truck traffic by the owner. The driver must satisfy himself of theabove before entering these areas. The truck must enter lifts with the load in front andmust take up a position which does not allow it to come into contact with the walls ofthe lift shaft. People travelling in the lift with the forklift truck must only enter the liftafter the truck has come to a halt and must exit the lift before the truck. The drivermust ensure that the loading ramp / bridge cannot move or come loose during loading/ unloading.

Type of loads to be carried

The operator must make sure that the load is in a satisfactory condition. Loads mustalways be positioned safely and carefully. Use suitable precautions to prevent partsof the load from tipping or falling down.

11.1

4 D

E

52

4.2 Emergency Disconnect, Travel, Steering, Braking

4.2.1 Emergency Disconnect (battery connector)

NOTE

The Emergency Disconnect safety function is performed by the battery connector thatcan be accessed from the outside.

Pressing the Emergency Disconnect switch

Procedure

CAUTION!Accident riskThe operation of the Emergency Disconnect switch must not be affected by anyobjects placed in its way.

Z Do not use the Emergency Disconnect switch (6) as a service brake. • Press the Emergency Disconnect (6).

All electrical functions are deactivated. The truck brakes to a halt.

Releasing the Emergency Disconnect switch

Procedure• Pull the Emergency Disconnect (6) to unlock it.

All electrical functions are enabled and the truck is operational again (assuming thetruck was not operational before the Emergency Disconnect was pressed).For CanCode and ISM the truck remains switched off.

11.1

4 D

E

52

4.2 Emergency Disconnect, Travel, Steering, Braking

4.2.1 Emergency Disconnect (battery connector)

NOTE

The Emergency Disconnect safety function is performed by the battery connector thatcan be accessed from the outside.

Pressing the Emergency Disconnect switch

Procedure

CAUTION!Accident riskThe operation of the Emergency Disconnect switch must not be affected by anyobjects placed in its way.

Z Do not use the Emergency Disconnect switch (6) as a service brake. • Press the Emergency Disconnect (6).

All electrical functions are deactivated. The truck brakes to a halt.

Releasing the Emergency Disconnect switch

Procedure• Pull the Emergency Disconnect (6) to unlock it.

All electrical functions are enabled and the truck is operational again (assuming thetruck was not operational before the Emergency Disconnect was pressed).For CanCode and ISM the truck remains switched off.

53

11.1

4 D

E

R

VR

V

0

B

BB

F

144

6

48

2

1

44

7

53

11.1

4 D

E

R

VR

V

0

B

BB

F

144

6

48

2

1

44

7

11.1

4 D

E

54

4.2.2 Travel

CAUTION!

Do not drive the truck unless the panels are closed and properly locked.

Trucks with a fixed operator platform

Requirements– Start up the truck, (see "Starting up the truck" on page 47)

Procedure• Step onto the operator platform (48).• Set the travel switch (1) to the desired travel direction: forward (V) or reverse (R).

Z When the travel switch is release it automatically returns to its original position.• Control the travel speed with the travel switch (1).

The brakes are released and the truck moves in the selected direction.

Industrial trucks with a folding standing platform and moving tiller

We distinguish between two travel modes:

– Travel in pedestrian mode– Travel in rider mode

WARNING!

Trapping hazardBe extremely careful when driving and steering, especially if parts of your bodyextend outside the border of the truck.Do not reach between the standing platform and the truck frame when you fold up

the platform.In pedestrian mode make sure you have sufficient distance from the industrial

truck.

Travelling in pedestrian mode


Procedure• Move both folding side arms (7) in.

Z Both side arms must always be folded in, otherwise all functions are deactivated(E-1926).

• Fold up the operator platform (8).• Set the tiller (2) to the travel zone (F).• Set the travel switch (1) to the desired travel direction: forward (V) or reverse (R).

Z When the travel switch is released it automatically returns to its original position.• Control the travel speed with the travel switch (1).


11.1

4 D

E

54

4.2.2 Travel

CAUTION!

Do not drive the truck unless the panels are closed and properly locked.

Trucks with a fixed operator platform


Procedure• Step onto the operator platform (48).• Set the travel switch (1) to the desired travel direction: forward (V) or reverse (R).

Z When the travel switch is release it automatically returns to its original position.• Control the travel speed with the travel switch (1).


Industrial trucks with a folding standing platform and moving tiller

We distinguish between two travel modes:

– Travel in pedestrian mode– Travel in rider mode

WARNING!

Trapping hazardBe extremely careful when driving and steering, especially if parts of your bodyextend outside the border of the truck.Do not reach between the standing platform and the truck frame when you fold up

the platform.In pedestrian mode make sure you have sufficient distance from the industrial

truck.

Travelling in pedestrian mode


Procedure• Move both folding side arms (7) in.

Z Both side arms must always be folded in, otherwise all functions are deactivated(E-1926).

• Fold up the operator platform (8).• Set the tiller (2) to the travel zone (F).• Set the travel switch (1) to the desired travel direction: forward (V) or reverse (R).



55

11.1

4 D

E

Z In pedestrian mode the truck can only operate at reduced speed.

Travelling in rider mode


Procedure• Move the folding side restraints (7) out.• Fold down the operator platform (8).• Set the tiller (2) to the travel zone (F).• Set the travel switch (1) to the desired travel direction: forward (V) or reverse (R).



Z Preventing the truck from “rolling downhill”:

If the truck rolls backwards on an incline the controller detects the situation and thetravel switch brake applies automatically after a short jerk.

NOTE

Travelling is inhibited when the operator platform is unladen and the side arms arenot folded out.

If the standing platform is occupied and the gates are not folded out, the industrialtruck can only be operated at reduced speed.

If the operator platform is occupied and only one gate is folded out, travelling isinhibited.

55

11.1

4 D

E

Z In pedestrian mode the truck can only operate at reduced speed.

Travelling in rider mode


Procedure• Move the folding side restraints (7) out.• Fold down the operator platform (8).• Set the tiller (2) to the travel zone (F).• Set the travel switch (1) to the desired travel direction: forward (V) or reverse (R).



Z Preventing the truck from “rolling downhill”:

If the truck rolls backwards on an incline the controller detects the situation and thetravel switch brake applies automatically after a short jerk.

NOTE

Travelling is inhibited when the operator platform is unladen and the side arms arenot folded out.

If the standing platform is occupied and the gates are not folded out, the industrialtruck can only be operated at reduced speed.

If the operator platform is occupied and only one gate is folded out, travelling isinhibited.

11.1

4 D

E

56

4.2.3 Steering

Procedure• Move the tiller (2) to the left or right.

The truck is steered in the required direction.

4.2.4 Brakes

The braking pattern of the truck depends largely on the travel conditions and the load.The driver must take this into account when travelling.

The truck can brake in different ways:

– By inversion braking (controller)– By regenerative braking (coasting)– With the stop button (fixed operator platform)– With the tiller set to the "B" zone (folding operator platform only)– With the Emergency Disconnect (in emergencies)

Inversion braking

Procedure• During travel, set the travel switch (1) to the opposite direction.

The truck brakes regeneratively until it starts to move in the opposite direction.

Z The brake force can be set by the manufacturer’s service department.

Regenerative braking

Procedure• If the travel switch is set to 0, the truck automatically brakes regeneratively.

The truck brakes to a halt regeneratively via the coasting brake. The parking brakethen applies.

Z With regenerative braking energy is recuperated to the battery, ensuring a longerservice time.

Braking with the stop button

Procedure• Press the stop button (44) or set the travel switch to the 0 position.

The truck brakes.

Z This braking mode is only available with fixed platform trucks.

Braking with the tiller in the "B" zone

Procedure• Move the tiller up or down to one of the brake zones (B).

Z Initially the truck brakes regeneratively. The mechanical brake is only applied whenthis brake fails to achieve the necessary braking force.

11.1

4 D

E

56

4.2.3 Steering

Procedure• Move the tiller (2) to the left or right.

The truck is steered in the required direction.

4.2.4 Brakes

The braking pattern of the truck depends largely on the travel conditions and the load.The driver must take this into account when travelling.

The truck can brake in different ways:

– By inversion braking (controller)– By regenerative braking (coasting)– With the stop button (fixed operator platform)– With the tiller set to the "B" zone (folding operator platform only)– With the Emergency Disconnect (in emergencies)

Inversion braking

Procedure• During travel, set the travel switch (1) to the opposite direction.

The truck brakes regeneratively until it starts to move in the opposite direction.

Z The brake force can be set by the manufacturer’s service department.

Regenerative braking

Procedure• If the travel switch is set to 0, the truck automatically brakes regeneratively.

The truck brakes to a halt regeneratively via the coasting brake. The parking brakethen applies.

Z With regenerative braking energy is recuperated to the battery, ensuring a longerservice time.

Braking with the stop button

Procedure• Press the stop button (44) or set the travel switch to the 0 position.

The truck brakes.

Z This braking mode is only available with fixed platform trucks.

Braking with the tiller in the "B" zone

Procedure• Move the tiller up or down to one of the brake zones (B).

Z Initially the truck brakes regeneratively. The mechanical brake is only applied whenthis brake fails to achieve the necessary braking force.

57

11.1

4 D

EThe truck will decelerate at the maximum rate and the brake will apply.

Z This braking mode is only available with folding platform trucks.

Braking with the Emergency Disconnect

CAUTION!

Accident riskOnly brake with the Emergency Disconnect in emergency situations. The truckbrakes at maximum force.

Procedure• Press the Emergency Disconnect (6) down.

The circuit is disconnected, all electrical functions are cut out and the industrial truckbrakes automatically (magnetic brake).

Z The truck can only start again when the Emergency Disconnect (6) has beenunlocked again by pulling it up.

57

11.1

4 D

E

The truck will decelerate at the maximum rate and the brake will apply.

Z This braking mode is only available with folding platform trucks.

Braking with the Emergency Disconnect

CAUTION!

Accident riskOnly brake with the Emergency Disconnect in emergency situations. The truckbrakes at maximum force.

Procedure• Press the Emergency Disconnect (6) down.

The circuit is disconnected, all electrical functions are cut out and the industrial truckbrakes automatically (magnetic brake).

Z The truck can only start again when the Emergency Disconnect (6) has beenunlocked again by pulling it up.

11.1

4 D

E

58

4.3 Lifting, transporting and depositing loads

WARNING!

Unsecured and incorrectly positioned loads can cause accidents Before lifting a load unit the driver must ensure that it has been correctly palletisedand does not exceed the truck’s capacity.Instruct other people to move out of the hazardous area of the industrial truck. Stop

working with the truck if people do not leave the hazardous area.Only carry loads that have been correctly secured and positioned. Use suitable

protection measure to prevent parts of the load from tipping or falling down.Damaged loads must not be transported.Never exceed the maximum loads specified on the capacity chart.Never stand underneath a raised load handler.Do not stand on the load handler.Do not lift other people on the load handler.Insert the load handler as far as possible underneath the load.

NOTE

Adapt a slower speed when stacking and retrieving.

NOTE

The operator platform (10) must be occupied by the operator for lifting/lowering to beenabled.

4.3.1 Lifting load units

Requirements– Load unit correctly palletised.– Load unit weight matches the truck's capacity.– Forks evenly loaded for heavy loads.

Procedure• Drive the truck carefully up to the pallet.• Slowly insert the forks into the pallet until the

fork shank touches the pallet.Z The load unit must not extend by more than 50

mm beyond the fork tips.• Press the “Lift” button (46) until you reach the desired lift height.

The load unit is raised.

45 46 4546

11.1

4 D

E

58

4.3 Lifting, transporting and depositing loads

WARNING!

Unsecured and incorrectly positioned loads can cause accidents Before lifting a load unit the driver must ensure that it has been correctly palletisedand does not exceed the truck’s capacity.Instruct other people to move out of the hazardous area of the industrial truck. Stop

working with the truck if people do not leave the hazardous area.Only carry loads that have been correctly secured and positioned. Use suitable

protection measure to prevent parts of the load from tipping or falling down.Damaged loads must not be transported.Never exceed the maximum loads specified on the capacity chart.Never stand underneath a raised load handler.Do not stand on the load handler.Do not lift other people on the load handler.Insert the load handler as far as possible underneath the load.

NOTE

Adapt a slower speed when stacking and retrieving.

NOTE

The operator platform (10) must be occupied by the operator for lifting/lowering to beenabled.

4.3.1 Lifting load units

Requirements– Load unit correctly palletised.– Load unit weight matches the truck's capacity.– Forks evenly loaded for heavy loads.

Procedure• Drive the truck carefully up to the pallet.• Slowly insert the forks into the pallet until the

fork shank touches the pallet.Z The load unit must not extend by more than 50

mm beyond the fork tips.• Press the “Lift” button (46) until you reach the desired lift height.

The load unit is raised.

45 46 4546

59

11.1

4 D

E4.3.2 Transport the load unit.

Transporting load units

Requirements– Load unit correctly lifted.– Good ground conditions.

Procedure• Accelerate and decelerate gradually.• Adapt your travel speed to the conditions of the route and the load you are

transporting.• Travel at a constant speed.• Watch out for other traffic at crossings and passageways. • Always travel with a lookout at blind spots.• On slopes and inclines always carry the load facing uphill, never approach at an

angle or turn.

59

11.1

4 D

E

4.3.2 Transport the load unit.

Transporting load units

Requirements– Load unit correctly lifted.– Good ground conditions.

Procedure• Accelerate and decelerate gradually.• Adapt your travel speed to the conditions of the route and the load you are

transporting.• Travel at a constant speed.• Watch out for other traffic at crossings and passageways. • Always travel with a lookout at blind spots.• On slopes and inclines always carry the load facing uphill, never approach at an

angle or turn.

11.1

4 D

E

60

4.3.3 Lowering the load unit

Depositing load units

NOTE

Loads must not be deposited on travel or escape routes, in front of safetymechanisms or operating equipment that must be accessible at all times.

Requirements– Warehouse location suitable for storing the load.

Procedure• Drive carefully up to the storage location.• Press the "Lower load handler" button until the forks are clear of the load.

Z Avoid depositing the load to avoid damaging the load and the load handler.• Carefully remove the forks from the pallet.

The load unit is lowered.

11.1

4 D

E

60

4.3.3 Lowering the load unit

Depositing load units

NOTE

Loads must not be deposited on travel or escape routes, in front of safetymechanisms or operating equipment that must be accessible at all times.

Requirements– Warehouse location suitable for storing the load.

Procedure• Drive carefully up to the storage location.• Press the "Lower load handler" button until the forks are clear of the load.

Z Avoid depositing the load to avoid damaging the load and the load handler.• Carefully remove the forks from the pallet.

The load unit is lowered.

61

11.1

4 D

E5 Troubleshooting

This chapter enables the user to identify and rectify basic faults and the effects ofincorrect operation. When trying to locate a fault, proceed in the order shown in thetable.

Z If, after carrying out the following remedial action, the truck cannot be restored tooperation or if a fault in the electronics system is displayed with a correspondingerror code, contact the manufacturer’s service department.Additional troubleshooting must only be performed by the manufacturer’s specialistservice engineers. The manufacturer's customer service department is speciallytrained to carry out these operations.In order for customer services to react quickly and specifically to the fault, thefollowing information is essential:- Truck serial number- Error number on the display unit (if applicable)- Error description- Current location of truck

5.1 Truck does not start

5.2 Load cannot be lifted

Possible Cause Remedy

Battery connector not plugged in Check the battery connector and connect if necessary

Emergency Disconnect pressed Unlock the Emergency Disconnect

Key switch set to O. Set the key switch to “I”

Battery charge too low Check battery charge, Charge the battery as required

Faulty fuse Check fuses

Incorrect ISM access module transponder used

Use correct transponder

Incorrect CANCode PIN entered Enter correct PIN

Tiller not in brake position when truck switched on(E-0914)

Set tiller to upper / lower brake position

Switch in mast implausible (E-2124) Emergency recovery (travel at max. 1.5 km/h and lowering possible when truck is in rider mode). Contact the manufacturer's service department.


Truck not operational Carry out all measures listed under “Truck does not start”.

Hydraulic oil level too low Checking the hydraulic oil level

61

11.1

4 D

E

5 Troubleshooting

This chapter enables the user to identify and rectify basic faults and the effects ofincorrect operation. When trying to locate a fault, proceed in the order shown in thetable.

Z If, after carrying out the following remedial action, the truck cannot be restored tooperation or if a fault in the electronics system is displayed with a correspondingerror code, contact the manufacturer’s service department.Additional troubleshooting must only be performed by the manufacturer’s specialistservice engineers. The manufacturer's customer service department is speciallytrained to carry out these operations.In order for customer services to react quickly and specifically to the fault, thefollowing information is essential:- Truck serial number- Error number on the display unit (if applicable)- Error description- Current location of truck

5.1 Truck does not start

5.2 Load cannot be lifted


Battery connector not plugged in Check the battery connector and connect if necessary

Emergency Disconnect pressed Unlock the Emergency Disconnect

Key switch set to O. Set the key switch to “I”

Battery charge too low Check battery charge, Charge the battery as required


Incorrect ISM access module transponder used

Use correct transponder

Incorrect CANCode PIN entered Enter correct PIN

Tiller not in brake position when truck switched on(E-0914)

Set tiller to upper / lower brake position



Truck not operational Carry out all measures listed under “Truck does not start”.

Hydraulic oil level too low Checking the hydraulic oil level

11.1

4 D

E

62

Battery discharge monitor has switched off

Charge the battery


Excessive load Note maximum capacity, see data plate.



11.1

4 D

E

62

Battery discharge monitor has switched off

Charge the battery


Excessive load Note maximum capacity, see data plate.



63

11.1

4 D

E6 Operating the truck without its own drive system

WARNING!

Uncontrolled truck movementWhen the brakes are de-activated the truck must be parked on a level surface, sincethe brakes are no longer effective.Do not release the brake on slopes or inclines.Apply the brake again when you reach your destination.Do not park the truck with the brake released.

Releasing the brake

Tools and Material Required– Two M5 screws– Spanner wrench

Procedure• Turn of the key switch, CanCode or ISM.• Press the Emergency Disconnect switch.• Prevent the truck from rolling away.• Open the battery panel.• Disconnect the battery.• Lift off the front panel (54) and put it to one side, (see "Removing the front panel"

on page 108).• Insert two M5 screws (55) as far as the stop and lift up the anchor plate.

The brake is now released and the truck can be moved.

Applying the brake

Procedure• Unscrew the two M5 (55) screws again.• Refit front panel (54).

Braking is now restored again.

63

11.1

4 D

E

6 Operating the truck without its own drive system

WARNING!

Uncontrolled truck movementWhen the brakes are de-activated the truck must be parked on a level surface, sincethe brakes are no longer effective.Do not release the brake on slopes or inclines.Apply the brake again when you reach your destination.Do not park the truck with the brake released.

Releasing the brake

Tools and Material Required– Two M5 screws– Spanner wrench

Procedure• Turn of the key switch, CanCode or ISM.• Press the Emergency Disconnect switch.• Prevent the truck from rolling away.• Open the battery panel.• Disconnect the battery.• Lift off the front panel (54) and put it to one side, (see "Removing the front panel"

on page 108).• Insert two M5 screws (55) as far as the stop and lift up the anchor plate.

The brake is now released and the truck can be moved.

Applying the brake

Procedure• Unscrew the two M5 (55) screws again.• Refit front panel (54).

Braking is now restored again.

11.1

4 D

E

64

55

54

11.1

4 D

E

64

55

54

65

11.1

4 D

E7 Optional equipment

7.1 CanCode keypad

CanCode keypad

The keypad consists of 10 digit keys, a Set key and a okey.

The O key indicates the follow operating statuses via ared / green LED:– Code lock function (starting up the truck).– Adjusting the travel program depending on the setting

and truck.– Setting and changing parameters.

7.1.1 Keypad

When the correct code is entered, the truck is ready for use. You can allocate anindividual code to each truck, operator or group of operators. When the truck issupplied from the factory, the code is indicated on a sticker. Change the master andoperator codes when you use the truck for the first time.

Z Set different codes for rider and pedestrian trucks.

Starting the truck

Procedure• Switching on the Emergency

Disconnect.LED (61) lights up red.

• Enter the code.When you enter the correct operatorcode the LED (61) turns green. If theLED (61) flashes red this means thewrong code has been entered. Tryagain.

The truck is switched on

Z The Set key (60) has no function in operating mode.

Switching the truck off

Procedure• Press the O key.

The truck is switched off.

Z The truck can switch off automatically after a set time. To do this the relevant codelock parameters must be entered, (see "Parameter Settings" on page 66).

1 2 3

4 5 6

7 8 9

0Set

1 2 3

4 5 6

7 8 9

0Set60

56 57 58

59

61

65

11.1

4 D

E

7 Optional equipment

7.1 CanCode keypad

CanCode keypad

The keypad consists of 10 digit keys, a Set key and a okey.

The O key indicates the follow operating statuses via ared / green LED:– Code lock function (starting up the truck).– Adjusting the travel program depending on the setting

and truck.– Setting and changing parameters.

7.1.1 Keypad

When the correct code is entered, the truck is ready for use. You can allocate anindividual code to each truck, operator or group of operators. When the truck issupplied from the factory, the code is indicated on a sticker. Change the master andoperator codes when you use the truck for the first time.


Starting the truck

Procedure• Switching on the Emergency

Disconnect.LED (61) lights up red.

• Enter the code.When you enter the correct operatorcode the LED (61) turns green. If theLED (61) flashes red this means thewrong code has been entered. Tryagain.

The truck is switched on

Z The Set key (60) has no function in operating mode.

Switching the truck off

Procedure• Press the O key.

The truck is switched off.

Z The truck can switch off automatically after a set time. To do this the relevant codelock parameters must be entered, (see "Parameter Settings" on page 66).

1 2 3

4 5 6

7 8 9

0Set

1 2 3

4 5 6

7 8 9

0Set60

56 57 58

59

61

11.1

4 D

E

66

7.1.2 Parameters

The keypad enables parameters to be adjusted in programming mode.

Parameter Groups

The parameter number is composed of three digits. The first digit refers to theparameter group as shown in Table 1. The second and third digits are numbered insequence from 00 to 99.

7.1.3 Parameter Settings

To change the truck settings you must enter the master code.

Z The master code factory setting is 7-2-9-5. Change the master code the first timeyou use the truck.


Changing the truck settings

Procedure• Press the O key (59).• Enter the master code.• Enter the three-digit parameter number. • Confirm with the SET key (60).• Enter the setting as per parameter list.

Z If the entry is incorrect, the LED (61) of the O key (59) turns red. • Enter the parameter number again.• Enter the setting again or change it.

• Confirm with the SET key (60).• Repeat the procedure for other parameters.• Then press the O key (59).

The settings are now saved.

No. Parameter Groups0XX Code lock settings (codes, travel program release, automatic cutout, etc.)

11.1

4 D

E

66

7.1.2 Parameters

The keypad enables parameters to be adjusted in programming mode.

Parameter Groups

The parameter number is composed of three digits. The first digit refers to theparameter group as shown in Table 1. The second and third digits are numbered insequence from 00 to 99.

7.1.3 Parameter Settings

To change the truck settings you must enter the master code.

Z The master code factory setting is 7-2-9-5. Change the master code the first timeyou use the truck.


Changing the truck settings

Procedure• Press the O key (59).• Enter the master code.• Enter the three-digit parameter number. • Confirm with the SET key (60).• Enter the setting as per parameter list.

Z If the entry is incorrect, the LED (61) of the O key (59) turns red. • Enter the parameter number again.• Enter the setting again or change it.

• Confirm with the SET key (60).• Repeat the procedure for other parameters.• Then press the O key (59).

The settings are now saved.

No. Parameter Groups0XX Code lock settings (codes, travel program release, automatic cutout, etc.)

67

11.1

4 D

EParameter list

No. Function Setting range Standard setting

Procedure

000 Change master code: The length (4-6 digits) of the master code also determines the length of the operator code (4-6 digits). Provided the operator codes are programmed, only new codes of the same length can be entered. If you wish to change the code length, you must first delete all the operator codes.

0000 - 9999 or

00000 - 99999 or

000000 - 999999

7295 – (LED 56 flashes) Confirm current code entry

–(Set 60)

– (LED 57 flashes)Enter a new code

–(Set 60)

– (LED 58 flashes) repeat new code

–(Set 60)

001 Add code (max. 250) 0000 - 9999 or

00000 - 99999 or

000000 - 999999

2580 – (LED 57 flashes)Confirm code entry

–(Set 60)

– (LED 58 flashes) repeat code entry

–(Set 60)

002 Change code 0000 - 9999 or

00000 - 99999 or

000000 - 999999

– (LED 56 flashes)Confirm current code entry

–(Set 60)

– (LED 57 flashes)Confirm new code entry

–(Set 60)

– (LED 58 flashes)Confirm code re-entry

–(Set 60)

LEDs 56-58 are located in keypads 1-3.

67

11.1

4 D

E

Parameter list


Procedure

000 Change master code: The length (4-6 digits) of the master code also determines the length of the operator code (4-6 digits). Provided the operator codes are programmed, only new codes of the same length can be entered. If you wish to change the code length, you must first delete all the operator codes.

0000 - 9999 or

00000 - 99999 or

000000 - 999999

7295 – (LED 56 flashes) Confirm current code entry

–(Set 60)

– (LED 57 flashes)Enter a new code

–(Set 60)

– (LED 58 flashes) repeat new code

–(Set 60)

001 Add code (max. 250) 0000 - 9999 or

00000 - 99999 or

000000 - 999999

2580 – (LED 57 flashes)Confirm code entry

–(Set 60)


–(Set 60)

002 Change code 0000 - 9999 or

00000 - 99999 or

000000 - 999999

– (LED 56 flashes)Confirm current code entry

–(Set 60)


–(Set 60)

– (LED 58 flashes)Confirm code re-entry

–(Set 60)


11.1

4 D

E

68

Assigning the starting travel program (depending on the truck)

The travel programs are connected to the code. The travel programs can beindividually released or blocked for each code. A starting travel program can beassigned to each code.

Once a user code has been set up, all travel programs are globally released, the validstart travel program is travel program 2.The code configuration can then be changed with program number 024.

1. digit: travel program 1 release (0 = blocked or 1 = released) 2nd digit: travel program 2 release (0 = blocked or 1 = released) 3rd digit: travel program 3 release (0 = blocked or 1 = released) 4th digit: start travel program (0, 1, 2 or 3)

003 Delete code 0000 - 9999 or

00000 - 99999 or

000000 - 999999


–(Set 60)


–(Set 60)

004 Delete code log (deletes all codes)

3265 – 3265 = delete– other inputs = do

not delete

010 Automatic timeout 00-31 00 – 00 = No timeout– 01 - 30 = Timeout

in minutes– 31 = Timeout after

10 seconds


Procedure



Procedure

024 Code configuration 1112

11.1

4 D

E

68

Assigning the starting travel program (depending on the truck)

The travel programs are connected to the code. The travel programs can beindividually released or blocked for each code. A starting travel program can beassigned to each code.

Once a user code has been set up, all travel programs are globally released, the validstart travel program is travel program 2.The code configuration can then be changed with program number 024.

1. digit: travel program 1 release (0 = blocked or 1 = released) 2nd digit: travel program 2 release (0 = blocked or 1 = released) 3rd digit: travel program 3 release (0 = blocked or 1 = released) 4th digit: start travel program (0, 1, 2 or 3)

003 Delete code 0000 - 9999 or

00000 - 99999 or

000000 - 999999


–(Set 60)


–(Set 60)

004 Delete code log (deletes all codes)

3265 – 3265 = delete– other inputs = do

not delete

010 Automatic timeout 00-31 00 – 00 = No timeout– 01 - 30 = Timeout

in minutes– 31 = Timeout after

10 seconds


Procedure



Procedure

024 Code configuration 1112

69

11.1

4 D

E

Setting the travel program configuration to a code

Procedure• Press the O key (59).• Enter the master code.• Enter the three-digit parameter number 024. • Confirm with the SET key (60).• Enter the code to be changed and confirm with SET.• Enter the configuration (4 digit) and confirm with SET.• Enter the configuration (4 digit) again and confirm with SET.• Repeat the procedure for other codes.• Then press the O key.

The travel programs are assigned to the codes

Keypad event messages

The LED (61) flashes red to indicate the following events:– New master code is already in use.– New code is already the master code– Code to be changed does not exist– Attempt to change the code to one that already exists.– Attempt to delete a code that does not exist– Code memory full.

69

11.1

4 D

E

Setting the travel program configuration to a code

Procedure• Press the O key (59).• Enter the master code.• Enter the three-digit parameter number 024. • Confirm with the SET key (60).• Enter the code to be changed and confirm with SET.• Enter the configuration (4 digit) and confirm with SET.• Enter the configuration (4 digit) again and confirm with SET.• Repeat the procedure for other codes.• Then press the O key.

The travel programs are assigned to the codes

Keypad event messages

The LED (61) flashes red to indicate the following events:– New master code is already in use.– New code is already the master code– Code to be changed does not exist– Attempt to change the code to one that already exists.– Attempt to delete a code that does not exist– Code memory full.

11.1

4 D

E

70

7.2 Setting the truck parameters with CanCode

CAUTION!

Faulty entryWithout CanDis only CanCode internal parameters can be changed. Tractioncontroller parameters can only be changed with CanDis, without CanDis the settingsmust be performed by the manufacturer's service department.

CAUTION!

Altering travel parameters can cause accidentsIncreasing the settings for travel and hydraulic functions can result in accidents.Carry out a test run in a secure environment.This requires greater attention on the part of the operator.

Parameter setting example:

The following example shows the parameter setting for the acceleration of travelprogram 1 (parameter 0256).

Acceleration example

Procedure• Enter four-digit parameter number "0256" and confirm with the SET key (60).• Enter sub-index (enter "2") and confirm with the SET key (60).

Z The parameter and sub index are displayed alternately with the current reading(0256-2<->0000-3).

• Enter the parameter according to the parameter list and confirm with the Set key(60).

Z The LED (61) of the O key (59) switches briefly to steady light and start flashingagain after approx. 2 seconds.

Z If the entry is incorrect, the LED (61) of the O key (59) turns red. Enter theparameter number again to repeat the setting.


The travel parameter is now set.

Repeat the procedure to enter further parameters as soon as the LED (61) of the Okey (59) flashes.

Z Travel is disabled while the parameters are being entered.

11.1

4 D

E

70

7.2 Setting the truck parameters with CanCode

CAUTION!

Faulty entryWithout CanDis only CanCode internal parameters can be changed. Tractioncontroller parameters can only be changed with CanDis, without CanDis the settingsmust be performed by the manufacturer's service department.

CAUTION!

Altering travel parameters can cause accidentsIncreasing the settings for travel and hydraulic functions can result in accidents.Carry out a test run in a secure environment.This requires greater attention on the part of the operator.

Parameter setting example:

The following example shows the parameter setting for the acceleration of travelprogram 1 (parameter 0256).

Acceleration example

Procedure• Enter four-digit parameter number "0256" and confirm with the SET key (60).• Enter sub-index (enter "2") and confirm with the SET key (60).


• Enter the parameter according to the parameter list and confirm with the Set key(60).

Z The LED (61) of the O key (59) switches briefly to steady light and start flashingagain after approx. 2 seconds.

Z If the entry is incorrect, the LED (61) of the O key (59) turns red. Enter theparameter number again to repeat the setting.


The travel parameter is now set.

Repeat the procedure to enter further parameters as soon as the LED (61) of the Okey (59) flashes.

Z Travel is disabled while the parameters are being entered.

71

11.1

4 D

E

Checking the settings in programming mode

Procedure• Select the travel program to be worked on after changing the parameter value, and

confirm with the Set key (60).

The truck is now in travel mode and can be checked.

Z To continue setting, confirm with the Set key (60) again.

Saving travel parameters

Requirements– Enter all parameters.

Procedure• Run "SaveParameters" by pressing 1-2-3-Set.• Confirm with the O key (59).

71

11.1

4 D

E

Checking the settings in programming mode

Procedure• Select the travel program to be worked on after changing the parameter value, and

confirm with the Set key (60).

The truck is now in travel mode and can be checked.

Z To continue setting, confirm with the Set key (60) again.

Saving travel parameters

Requirements– Enter all parameters.

Procedure• Run "SaveParameters" by pressing 1-2-3-Set.• Confirm with the O key (59).

11.1

4 D

E

72

7.3 Traction controller AS2412i parameters

Travel program 1 - Fixed Platform

Travel program 1 - Folding Platform

No. Function Setting range

Standard setting

Comments

0256 Rider mode acceleration

0 - 9 2

0264 Maximum forward speed using travel switch

0 - 9(8.5 - 13.0

km/h)

29.5 km/h

0268 Maximum reverse speed using travel switch

0 - 9(8.5 - 13.0

km/h)

99.5 km/h

0260 Rider mode coasting brake

0 - 9 2

0262 Inversion brake 0 - 9 7


Standard setting

Comments


0 - 9 2 Platform folded out, side arm folded out


0 - 9(8.5 - 13.0

km/h)

29.5 km/h


0 - 9(8.5 - 13.0

km/h)

29.5 km/h


0 - 9 2


0 - 9 4 Platform folded in, side arm folded in


0 - 9(1.5 - 4.5 km/

h)

84.0 km/h

0269 Maximum pedestrian reverse speed using travel switch

0 - 9(1.5 - 4.5 km/

h)

84.0 km/h

0261 Pedestrian mode coasting brake

0 - 9 7

0267 Special travel speed, forward

0 - 9(1.5 - 6.0 km/

h)

96.0 km/h

Platform folded out, side arm folded in.

0271 Special travel speed, reverse

0 - 9(1.5 - 6.0 km/

h)

96.0 km/h


11.1

4 D

E

72

7.3 Traction controller AS2412i parameters




Standard setting

Comments


0 - 9 2


0 - 9(8.5 - 13.0

km/h)

29.5 km/h


0 - 9(8.5 - 13.0

km/h)

99.5 km/h


0 - 9 2



Standard setting

Comments


0 - 9 2 Platform folded out, side arm folded out


0 - 9(8.5 - 13.0

km/h)

29.5 km/h


0 - 9(8.5 - 13.0

km/h)

29.5 km/h


0 - 9 2


0 - 9 4 Platform folded in, side arm folded in


0 - 9(1.5 - 4.5 km/

h)

84.0 km/h


0 - 9(1.5 - 4.5 km/

h)

84.0 km/h


0 - 9 7


0 - 9(1.5 - 6.0 km/

h)

96.0 km/h



0 - 9(1.5 - 6.0 km/

h)

96.0 km/h


73

11.1

4 D

E

Travel program 2 - fixed travel program


Standard setting

Comments


0 - 9 6


0 - 9(8.5 - 13.0

km/h)

812.5 km/h


0 - 9(8.5 - 13.0

km/h)

912.5 km/h


0 - 9 5

0262 Reversible brake 0 - 9 7

73

11.1

4 D

E



Standard setting

Comments


0 - 9 6


0 - 9(8.5 - 13.0

km/h)

812.5 km/h


0 - 9(8.5 - 13.0

km/h)

912.5 km/h


0 - 9 5


11.1

4 D

E

74



Standard setting

Comments


0 - 9 6 Platform folded out, side restraint folded out0280 Maximum forward

speed using travel switch

0 - 9(1.5 - 13.0

km/h)

812.5 km/h


0 - 9(1.5 - 13.0

km/h)

812.5 km/h


0 - 9 5


0 - 9 4 Platform folded in, side restraint folded in


0 - 9(1.5 - 4.5

km/h)

84.0 km/h


0 - 9(1.5 - 4.5

km/h)

84.0 km/h


0 - 9 7


0 - 9(1.5 - 6.0

km/h)

96.0 km/h

Platform folded out, side restraint folded in


0 - 9(1.5 - 6.0

km/h)

96.0 km/h


11.1

4 D

E

74



Standard setting

Comments


0 - 9 6 Platform folded out, side restraint folded out0280 Maximum forward

speed using travel switch

0 - 9(1.5 - 13.0

km/h)

812.5 km/h


0 - 9(1.5 - 13.0

km/h)

812.5 km/h


0 - 9 5


0 - 9 4 Platform folded in, side restraint folded in


0 - 9(1.5 - 4.5

km/h)

84.0 km/h


0 - 9(1.5 - 4.5

km/h)

84.0 km/h


0 - 9 7


0 - 9(1.5 - 6.0

km/h)

96.0 km/h

Platform folded out, side restraint folded in


0 - 9(1.5 - 6.0

km/h)

96.0 km/h


75

11.1

4 D

E



Standard setting

Comments


0 - 9 8


0 - 9(8.5 - 13.0

km/h)

812.5 km/h


0 - 9(8.5 - 13.0

km/h)

812.5 km/h


0 - 9 8


75

11.1

4 D

E



Standard setting

Comments


0 - 9 8


0 - 9(8.5 - 13.0

km/h)

812.5 km/h


0 - 9(8.5 - 13.0

km/h)

812.5 km/h


0 - 9 8


11.1

4 D

E

76


PM2402z steering controller battery parameters


Standard setting

Comments


0 - 9 8Platform folded out, side arm folded out


0 - 9(8.5 - 13.0

km/h)

812.5 km/h


0 - 9(8.5 - 13.0

km/h)

812.5 km/h


0 - 9 8

0289 Pedestrian mode acceleration

0 - 9 4Platform folded in, side arm folded in


0 - 9(1.5 - 4.5 km/

h)

84.0 km/h


0 - 9(1.5 - 4.5 km/

h)

84.0 km/h


0 - 9 7


0 - 9(1.5 - 6.0 km/

h)

96.0 km/h



0 - 9(1.5 - 6.0 km/

h)

96.0 km/h



Standard setting

Comments

1377 Battery type (normal / high performance / dry)

0 - 2 1 0 = Normal (wet)

1 = High performance (wet)

2 = Dry (maintenance-free)

1389 Discharge monitor function

0 /1 1 0 = Not active1 = Active

11.1

4 D

E

76


PM2402z steering controller battery parameters


Standard setting

Comments


0 - 9 8Platform folded out, side arm folded out


0 - 9(8.5 - 13.0

km/h)

812.5 km/h


0 - 9(8.5 - 13.0

km/h)

812.5 km/h


0 - 9 8

0289 Pedestrian mode acceleration

0 - 9 4Platform folded in, side arm folded in


0 - 9(1.5 - 4.5 km/

h)

84.0 km/h


0 - 9(1.5 - 4.5 km/

h)

84.0 km/h


0 - 9 7


0 - 9(1.5 - 6.0 km/

h)

96.0 km/h



0 - 9(1.5 - 6.0 km/

h)

96.0 km/h



Standard setting

Comments


0 - 2 1 0 = Normal (wet)




0 /1 1 0 = Not active1 = Active

77

11.1

4 D

E7.4 AS2412iS combi controller parameters



Standard setting

Comments


32 -10442

0.42 m/s2


45 - 13095

9.5 km/h

Side restraints folded out.


45 - 13095

9.5 km/h

Side restraints folded out


56 - 33080

0.8 m/s2

0262 Inversion brake 112 - 220

1801.8 m/s2

77

11.1

4 D

E

7.4 AS2412iS combi controller parameters



Standard setting

Comments


32 -10442

0.42 m/s2


45 - 13095

9.5 km/h

Side restraints folded out.


45 - 13095

9.5 km/h



56 - 33080

0.8 m/s2


1801.8 m/s2

11.1

4 D

E

78



Standard setting

Comments


32 - 10442

0.42 m/s2


45 - 13095

9.5 km/h



45 - 13095

9.5 km/h



56 - 33080

0.8 m/s2


4 - 2121

0.21 m/s2

0265 Forward pedestrian speed using travel switch

5 - 4540

4.0 km/h

0269 Reverse pedestrian speed using travel switch

5 - 4540

4.0 km/h


56 - 33080

0.8 m/s2

0267 Special forward speed

15 - 6060

6.0 km/hSide restraints folded in

0271 Special reverse speed

15 - 6060



1801.8 m/s2

11.1

4 D

E

78



Standard setting

Comments


32 - 10442

0.42 m/s2


45 - 13095

9.5 km/h



45 - 13095

9.5 km/h



56 - 33080

0.8 m/s2


4 - 2121

0.21 m/s2


5 - 4540

4.0 km/h


5 - 4540

4.0 km/h


56 - 33080

0.8 m/s2


15 - 6060



15 - 6060



1801.8 m/s2

79

11.1

4 D

E



Standard setting

Comments


32 -10470

0.70 m/s2


45 - 130125

12.5 km/h



45 - 130125

12.5 km/h



56 - 330130

1.3 m/s2


1801.8 m/s2

79

11.1

4 D

E



Standard setting

Comments


32 -10470

0.70 m/s2


45 - 130125

12.5 km/h



45 - 130125

12.5 km/h



56 - 330130

1.3 m/s2


1801.8 m/s2

11.1

4 D

E

80



Standard setting

Comments


32 - 10470

0.70 m/s2


45 -130125

12.5 km/h



45 -130125

12.5 km/h



56 -330130

1.3 m/s2


4 - 2121

0.21 m/s2


5 - 4542

4.2 km/h


5 - 4542

4.2 km/h


56 -330130

1.3 m/s2


15 - 6060



15 - 6060



1801.8 m/s2

11.1

4 D

E

80



Standard setting

Comments


32 - 10470

0.70 m/s2


45 -130125

12.5 km/h



45 -130125

12.5 km/h



56 -330130

1.3 m/s2


4 - 2121

0.21 m/s2


5 - 4542

4.2 km/h


5 - 4542

4.2 km/h


56 -330130

1.3 m/s2


15 - 6060



15 - 6060



1801.8 m/s2

81

11.1

4 D

E



Standard setting

Comments


32 -104100

1.00 m/s2


45 - 130125

12.5 km/h



45 - 130125

12.5 km/h



56 - 330145

1.45 m/s2


1801.8 m/s2

81

11.1

4 D

E



Standard setting

Comments


32 -104100

1.00 m/s2


45 - 130125

12.5 km/h



45 - 130125

12.5 km/h



56 - 330145

1.45 m/s2


1801.8 m/s2

11.1

4 D

E

82



Standard setting

Comments


32 - 104100

1.00 m/s2


45 -130125

12.5 km/h



45 -130125

12.5 km/h



56 -330145

1.45 m/s2


4 - 2121

0.21 m/s2


5 - 4542

4.2 km/h


5 - 4542

4.2 km/h


56 -330145

1.45 m/s2


15 - 6060



15 - 6060



1801.8 m/s2

11.1

4 D

E

82



Standard setting

Comments


32 - 104100

1.00 m/s2


45 -130125

12.5 km/h



45 -130125

12.5 km/h



56 -330145

1.45 m/s2


4 - 2121

0.21 m/s2


5 - 4542

4.2 km/h


5 - 4542

4.2 km/h


56 -330145

1.45 m/s2


15 - 6060



15 - 6060



1801.8 m/s2

83

11.1

4 D

EBattery parameters


Standard setting

Comments


0 - 7 1 0 = Normal (wet)



3 = US "Flat Plate"type

4 = US "Pallet Pro" type

5 = US "Tubular Plate"/dry battery type

6 = Banner DB69 (dry battery)

7 = Exide GF12 063 Y (dry battery)


0 - 4 1 0 = Not active

1 = Active

2 = Display and lift cutout active (except for digital lift input)

3 = Display and lift cutout active (except for MFC05 lift setpoints)

4 = Display and lift cutout active (except for MFC05 lift setpoints and digital lift input)

83

11.1

4 D

E

Battery parameters


Standard setting

Comments


0 - 7 1 0 = Normal (wet)



3 = US "Flat Plate"type

4 = US "Pallet Pro" type

5 = US "Tubular Plate"/dry battery type

6 = Banner DB69 (dry battery)

7 = Exide GF12 063 Y (dry battery)


0 - 4 1 0 = Not active

1 = Active

2 = Display and lift cutout active (except for digital lift input)

3 = Display and lift cutout active (except for MFC05 lift setpoints)

4 = Display and lift cutout active (except for MFC05 lift setpoints and digital lift input)

11.1

4 D

E

84

7.5 CanDis display instrument

The instrument indicates:

In addition, service messages for the electronic components and parameter changesare displayed.

Discharge status display

Setting limits for the additional “Warning” (64) and “Stop” (65) displays will depend onthe battery type.

The available capacity is shown via 8 LED bars.

The current battery capacity is shown by the illuminated LED bars. 8 bars correspondto full battery capacity, 1 bar corresponds to the minimum available capacity.

If only one LED bar is lit, the battery capacity is almost depleted and the “Warning”indicator (64) is lit. The battery must be charged immediately.

If no more LED bars are illuminated, the “Stop” indicator (65) lights up. Lifting is nowinhibited. The battery must be charged.

7.5.1 Discharge monitor function

When the discharge monitor function is enabled, lifting is cut out when reaching thedischarge limit is reached (the Stop LED goes on). Travel and lowering are stillpossible.

62Battery charge display (on board charger only)

63Capacity display barsBattery residual charge status

64Warning - pre-warning symbol,Battery charge recommended

65Stop symbol; lift cut-out,Battery charge required

66T symbol appears during operation when the discharge indicator is set to maintenance-free battery

676 digit LCD display;Hour meter, input display;Error display

62

64

66

63

65

67

11.1

4 D

E

84

7.5 CanDis display instrument

The instrument indicates:

In addition, service messages for the electronic components and parameter changesare displayed.

Discharge status display

Setting limits for the additional “Warning” (64) and “Stop” (65) displays will depend onthe battery type.

The available capacity is shown via 8 LED bars.

The current battery capacity is shown by the illuminated LED bars. 8 bars correspondto full battery capacity, 1 bar corresponds to the minimum available capacity.

If only one LED bar is lit, the battery capacity is almost depleted and the “Warning”indicator (64) is lit. The battery must be charged immediately.

If no more LED bars are illuminated, the “Stop” indicator (65) lights up. Lifting is nowinhibited. The battery must be charged.

7.5.1 Discharge monitor function

When the discharge monitor function is enabled, lifting is cut out when reaching thedischarge limit is reached (the Stop LED goes on). Travel and lowering are stillpossible.

62Battery charge display (on board charger only)

63Capacity display barsBattery residual charge status

64Warning - pre-warning symbol,Battery charge recommended

65Stop symbol; lift cut-out,Battery charge required

66T symbol appears during operation when the discharge indicator is set to maintenance-free battery

676 digit LCD display;Hour meter, input display;Error display

62

64

66

63

65

67

85

11.1

4 D

E7.5.2 Service hour display

Display range between 0.0 and 99,999.0 hours. Travel and lifting operations arelogged. This is a backlit display.

Z For maintenance-free batteries a “T” symbol is shown in the hourmeterdisplay (66).

7.5.3 Event Messages

The service hours display is also used to display event messages. The error displaystarts with an ”E” for Event and a four-digit error number.If several events occur simultaneously, they are displayed one after the other. Theevents are displayed until they are rectified. Event messages overwrite the servicehour display. Most events cause the Emergency Stop to be activated. Events remaindisplayed until the control circuit is switched off (key switch).

If no CanDis is present, the event code is displayed by the flashing of the dischargemonitor LED.

Z The manufacturer’s service department has detailed component descriptions withevent codes.

7.5.4 Power up test

On power up the display shows:

– The software version of the display instrument (briefly),– The service hours,– The battery charge status.

7.6 ISM access module (o)

Z If the truck is equipped with an ISM access module or Can Code refer to the “ISMAccess Module” operator manual.

7.7 Curve Control

The Curve Control option assists the driver to operating the truck with regard to safetyregulations. At corners the maximum travel speed is adapted to the steer angle.

85

11.1

4 D

E

7.5.2 Service hour display

Display range between 0.0 and 99,999.0 hours. Travel and lifting operations arelogged. This is a backlit display.

Z For maintenance-free batteries a “T” symbol is shown in the hourmeterdisplay (66).

7.5.3 Event Messages

The service hours display is also used to display event messages. The error displaystarts with an ”E” for Event and a four-digit error number.If several events occur simultaneously, they are displayed one after the other. Theevents are displayed until they are rectified. Event messages overwrite the servicehour display. Most events cause the Emergency Stop to be activated. Events remaindisplayed until the control circuit is switched off (key switch).

If no CanDis is present, the event code is displayed by the flashing of the dischargemonitor LED.

Z The manufacturer’s service department has detailed component descriptions withevent codes.

7.5.4 Power up test

On power up the display shows:

– The software version of the display instrument (briefly),– The service hours,– The battery charge status.

7.6 ISM access module (o)

Z If the truck is equipped with an ISM access module or Can Code refer to the “ISMAccess Module” operator manual.

7.7 Curve Control

The Curve Control option assists the driver to operating the truck with regard to safetyregulations. At corners the maximum travel speed is adapted to the steer angle.

11.1

4 D

E

86

11.1

4 D

E

86

87

11.1

4 D

E

F Industrial Truck Maintenance

1 Operational Safety and Environmental Protection

The checks and servicing operations contained in this chapter must be performed inaccordance with the intervals as indicated in the servicing checklists.

WARNING!

Risk of accidents and damage to componentsAll modifications to the forklift truck assemblies, in particular the safety mechanisms,are prohibited. The operating speeds of the truck must not be increased under anycircumstances.

NOTE

Only original spare parts have been certified by our quality assurance department. Toensure safe and reliable operation of the truck, use only the manufacturer's spareparts.For safety reasons, only components which have been specially agreed by themanufacturer for this truck may be installed near the computer, controllers and wireguidance sensors (antennae). These components (computers, controllers, wireguidance sensors (antennae)) must therefore not be replaced either by similarcomponents from other trucks of the same series.

2 Maintenance Safety Regulations


The truck should only be serviced and repaired by the manufacturer's specialistcustomer service personnel who have been trained to do this. We thereforerecommend that you enter into a maintenance contract with the manufacturer’s localsales office.

87

11.1

4 D

E

F Industrial Truck Maintenance

1 Operational Safety and Environmental Protection

The checks and servicing operations contained in this chapter must be performed inaccordance with the intervals as indicated in the servicing checklists.

WARNING!

Risk of accidents and damage to componentsAll modifications to the forklift truck assemblies, in particular the safety mechanisms,are prohibited. The operating speeds of the truck must not be increased under anycircumstances.

NOTE

Only original spare parts have been certified by our quality assurance department. Toensure safe and reliable operation of the truck, use only the manufacturer's spareparts.For safety reasons, only components which have been specially agreed by themanufacturer for this truck may be installed near the computer, controllers and wireguidance sensors (antennae). These components (computers, controllers, wireguidance sensors (antennae)) must therefore not be replaced either by similarcomponents from other trucks of the same series.

2 Maintenance Safety Regulations


The truck should only be serviced and repaired by the manufacturer's specialistcustomer service personnel who have been trained to do this. We thereforerecommend that you enter into a maintenance contract with the manufacturer’s localsales office.

11.1

4 D

E

88

Lifting and jacking up

WARNING!

Lifting and jacking up the truck safelyIn order to raise the truck, the lifting gear must only be secured to the points speciallyprovided for this purpose. You may only work under a raised load handler / raised cab if they have been securedwith a sufficiently strong chain or the fastening bolt.In order to raise and jack up the truck safely, proceed as follows:Jack up the truck only on a level surface and prevent it from moving accidentally.Always use a jack with sufficient capacity. When jacking up the truck, take

appropriate measures to prevent it from slipping or tipping over (e.g. wedges,wooden blocks).

In order to raise the truck, the lifting gear must only be secured to the pointsspecially provided for this purpose, (see "Transport and Commissioning" onpage 29).

When jacking up the truck, take appropriate measures to prevent it from slipping ortipping over (e.g. wedges, wooden blocks).

Cleaning

CAUTION!

Fire hazardDo not use flammable liquids to clean the industrial truck.Always disconnect the battery before starting cleaning work.Carry out all necessary safety measures to prevent sparking before cleaning (e.g.

by short-circuiting).

CAUTION!

Risk of electrical system damageThe electrical system can be damaged if it is cleaning with water. It is prohibited toclean the electrical system with water.Do not clean the electrical system with water.Clean the electrical system with weak suction or compressed air (use a compressor

with a water trap) and not a conductive, anti-static brush.

CAUTION!

Risk of component damage when cleaning the truckIf the truck is to be cleaned with a water jet or a high-pressure cleaner, all electricaland electronic components must be carefully covered beforehand as moisture cancause malfunctions. Do not clean with pressurised water.

Z After cleaning, carry out the operations detailed in “Recommissioning the truck aftercleaning or maintenance work” ((see "Restoring the truck to service aftermaintenance and repairs" on page 112)).

11.1

4 D

E

88

Lifting and jacking up

WARNING!

Lifting and jacking up the truck safelyIn order to raise the truck, the lifting gear must only be secured to the points speciallyprovided for this purpose. You may only work under a raised load handler / raised cab if they have been securedwith a sufficiently strong chain or the fastening bolt.In order to raise and jack up the truck safely, proceed as follows:Jack up the truck only on a level surface and prevent it from moving accidentally.Always use a jack with sufficient capacity. When jacking up the truck, take




Cleaning

CAUTION!

Fire hazardDo not use flammable liquids to clean the industrial truck.Always disconnect the battery before starting cleaning work.Carry out all necessary safety measures to prevent sparking before cleaning (e.g.

by short-circuiting).

CAUTION!

Risk of electrical system damageThe electrical system can be damaged if it is cleaning with water. It is prohibited toclean the electrical system with water.Do not clean the electrical system with water.Clean the electrical system with weak suction or compressed air (use a compressor

with a water trap) and not a conductive, anti-static brush.

CAUTION!

Risk of component damage when cleaning the truckIf the truck is to be cleaned with a water jet or a high-pressure cleaner, all electricaland electronic components must be carefully covered beforehand as moisture cancause malfunctions. Do not clean with pressurised water.

Z After cleaning, carry out the operations detailed in “Recommissioning the truck aftercleaning or maintenance work” ((see "Restoring the truck to service aftermaintenance and repairs" on page 112)).

89

11.1

4 D

EElectrical system

WARNING!

Accident riskOnly suitably trained electricians may operate on the truck's electrical system.Before working on the electrical system, take all precautionary measures to avoid

electric shocks.Always disconnect the battery before starting cleaning operations.

WARNING!

Electric currents can cause accidentsMake sure the electrical system is voltage-free before starting work on it. Beforestarting maintenance on the electrical system:Park the truck securely ((see "Parking the truck securely" on page 49)).Press the Emergency Disconnect. Disconnect the battery.Remove any rings or metal bracelets etc. before working on electrical components.

Consumables and used parts

CAUTION!

Consumables and used parts are an environmental hazardUsed parts, oils and fuels must be disposed of in accordance with the relevantenvironmental protection regulations. To change the oil contact the manufacturer'scustomer service department, who have been specially trained for this task.Note the safety regulations when handling these materials.

Welding

Remove electrical and electronic components from the truck before performingwelding operations, to avoid damage.

Settings

When repairing or replacing hydraulic, electric or electronic components orassemblies, always note the truck-specific settings.

89

11.1

4 D

E

Electrical system

WARNING!

Accident riskOnly suitably trained electricians may operate on the truck's electrical system.Before working on the electrical system, take all precautionary measures to avoid

electric shocks.Always disconnect the battery before starting cleaning operations.

WARNING!

Electric currents can cause accidentsMake sure the electrical system is voltage-free before starting work on it. Beforestarting maintenance on the electrical system:Park the truck securely ((see "Parking the truck securely" on page 49)).Press the Emergency Disconnect. Disconnect the battery.Remove any rings or metal bracelets etc. before working on electrical components.


CAUTION!


Welding

Remove electrical and electronic components from the truck before performingwelding operations, to avoid damage.

Settings

When repairing or replacing hydraulic, electric or electronic components orassemblies, always note the truck-specific settings.

11.1

4 D

E

90

Wheels

WARNING!

The use of wheels that do not match the manufacturer's specifications canresult in accidents.The quality of wheels affects the stability and performance of the truck. Uneven wear affects the truck's stability and increases the stopping distance. When replacing wheels make sure the truck is not skewed.Always replace wheels in pairs, i.e. left and right at the same time.

Z When replacing wheels fitted at the factory, only use the manufacturer’s originalspare parts. Otherwise the truck's rated performance cannot be ensured.

Hydraulic hoses

WARNING!

Leaky hydraulic systems can result in accidentsHydraulic oil can escape from leaky and faulty hydraulic systems.Report any defects immediately to your supervisor.Mark defective truck and take out of service.Do not return the industrial truck to service until you have identified and rectified the

fault.Remove any spilled hydraulic immediately with an appropriate bonding agent.The bonding agent / consumable mixture must be disposed of in accordance with

regulations.

WARNING!

Faulty hydraulic hoses can result in injury and infectionPressurised hydraulic oil can escape from fine holes or hairline cracks in the hydraulichoses. Brittle hydraulic hoses can burst during operation. People standing near thetruck can be injured by the hydraulic oil.Call for a doctor immediately in the event of an injury.Do not touch pressurised hydraulic hoses. Report any defects immediately to your supervisor.Mark defective truck and take it out of service.Do not return the industrial truck to service until you have identified and rectified the

fault.

11.1

4 D

E

90

Wheels

WARNING!

The use of wheels that do not match the manufacturer's specifications canresult in accidents.The quality of wheels affects the stability and performance of the truck. Uneven wear affects the truck's stability and increases the stopping distance. When replacing wheels make sure the truck is not skewed.Always replace wheels in pairs, i.e. left and right at the same time.

Z When replacing wheels fitted at the factory, only use the manufacturer’s originalspare parts. Otherwise the truck's rated performance cannot be ensured.

Hydraulic hoses

WARNING!

Leaky hydraulic systems can result in accidentsHydraulic oil can escape from leaky and faulty hydraulic systems.Report any defects immediately to your supervisor.Mark defective truck and take out of service.Do not return the industrial truck to service until you have identified and rectified the

fault.Remove any spilled hydraulic immediately with an appropriate bonding agent.The bonding agent / consumable mixture must be disposed of in accordance with

regulations.

WARNING!

Faulty hydraulic hoses can result in injury and infectionPressurised hydraulic oil can escape from fine holes or hairline cracks in the hydraulichoses. Brittle hydraulic hoses can burst during operation. People standing near thetruck can be injured by the hydraulic oil.Call for a doctor immediately in the event of an injury.Do not touch pressurised hydraulic hoses. Report any defects immediately to your supervisor.Mark defective truck and take it out of service.Do not return the industrial truck to service until you have identified and rectified the

fault.

91

11.1

4 D

E

NOTE

Testing and replacing hydraulic hosesHydraulic hoses can become brittle through age and must be checked at regularintervals. The application conditions of the industrial truck have a considerable impacton the ageing of the hydraulic hoses.Check the hydraulic hoses at least annually and replace if necessary.If the operating conditions become more arduous the inspection intervals must be

reduced accordingly.In normal operating conditions a precautionary replacement of the hydraulic hoses

is recommended after 6. The owner must carry out a risk assessment to ensuresafe, prolonged use. The resulting protection measures must be observed and theinspection interval reduced accordingly.

91

11.1

4 D

E

NOTE

Testing and replacing hydraulic hosesHydraulic hoses can become brittle through age and must be checked at regularintervals. The application conditions of the industrial truck have a considerable impacton the ageing of the hydraulic hoses.Check the hydraulic hoses at least annually and replace if necessary.If the operating conditions become more arduous the inspection intervals must be

reduced accordingly.In normal operating conditions a precautionary replacement of the hydraulic hoses

is recommended after 6. The owner must carry out a risk assessment to ensuresafe, prolonged use. The resulting protection measures must be observed and theinspection interval reduced accordingly.

11.1

4 D

E

92

3 Servicing and Inspection

Thorough and expert servicing is one of the most important requirements for the safeoperation of the industrial truck. Failure to perform regular servicing can lead to truckfailure and poses a potential hazard to personnel and equipment.

WARNING!

The application conditions of an industrial truck have a considerable impact on thewear of the service components.We recommend that a Jungheinrich customer service adviser carries out anapplication analysis on site to work out specific service intervals to prevent damagedue to wear.The service intervals stated are based on single shift operation under normaloperating conditions. They must be reduced accordingly if the truck is to be used inconditions of extreme dust, temperature fluctuations or multiple shifts.

The following servicing checklist indicates the operations to be performed and therespective intervals to be observed. Maintenance intervals are defined as:

Z W maintenance intervals must be performed by the owner.

During the run-in period – after approx. 100 service hours – the owner must check thewheel nuts / bolts and re-tighten if necessary.

W = Every 50 service hours, at least weekly

A = Every 500 service hours

B = Every 1000 service hours, or at least annually

C = Every 2000 service hours, or at least annually

t = Standard maintenance interval

k =Cold store maintenance interval (in addition to standard maintenance interval)

11.1

4 D

E

92

3 Servicing and Inspection

Thorough and expert servicing is one of the most important requirements for the safeoperation of the industrial truck. Failure to perform regular servicing can lead to truckfailure and poses a potential hazard to personnel and equipment.

WARNING!

The application conditions of an industrial truck have a considerable impact on thewear of the service components.We recommend that a Jungheinrich customer service adviser carries out anapplication analysis on site to work out specific service intervals to prevent damagedue to wear.The service intervals stated are based on single shift operation under normaloperating conditions. They must be reduced accordingly if the truck is to be used inconditions of extreme dust, temperature fluctuations or multiple shifts.

The following servicing checklist indicates the operations to be performed and therespective intervals to be observed. Maintenance intervals are defined as:

Z W maintenance intervals must be performed by the owner.

During the run-in period – after approx. 100 service hours – the owner must check thewheel nuts / bolts and re-tighten if necessary.

W = Every 50 service hours, at least weekly

A = Every 500 service hours

B = Every 1000 service hours, or at least annually

C = Every 2000 service hours, or at least annually

t = Standard maintenance interval

k =Cold store maintenance interval (in addition to standard maintenance interval)

93

11.1

4 D

E4 Maintenance checklist ERE 225 fixed platform

4.1 Proprietor

4.1.1 Standard equipment

Brakes W A B C

1 Test brakes. t

Electrical System W A B C

1Test warning and safety devices in accordance with operating instructions.

t

2 Test Emergency Disconnect switch. t

Power Supply W A B C

1Check battery cable connections are secure, grease terminals if necessary.

t

2 Check battery and battery components. t

3Check battery connector for damage, test it and make sure it is secure.

t

Travel W A B C

1 Check wheels for wear and damage. t

Chassis and superstructure W A B C

1 Check doors and/or covers. t2 Check labels are legible and complete. t

Hydraulic operations W A B C

1 Test hydraulic system. t2 Check hydraulic oil level and top up if necessary. t3 Check forks or load handler for wear and damage. t

93

11.1

4 D

E

4 Maintenance checklist ERE 225 fixed platform

4.1 Proprietor


Brakes W A B C

1 Test brakes. t



t




t



t

Travel W A B C






11.1

4 D

E

94

4.2 Customer Service


Brakes W A B C

1 Test brakes. t2 Check magnetic brake air gap. t


1 Test cable and motor attachments. t


t

3 Test displays and controls. t4 Test micro switch and adjust if necessary. t5 Test Emergency Disconnect switch. t6 Check contactors and/or relays. t7 Check fuse ratings. t

8Check carbon brushes and replace if necessary. Note: when replacing the carbon brushes apply compressed air to the motor.

t

9 Carry out a frame leakage test. t

10Check electric wiring for damage (insulation damage, connections). Make sure wire connections are secure.

t



t

2 Check battery and battery components. t3 Check acid density and battery voltage. t


t

Travel W A B C

1 Test Deadman switch. t2 Checking bedding and attachment of the drive system. t3 Check transmission for noise and leakage. t4 Note: Replace transmission oil after 10000 service hours.

5 Check wheels for wear and damage. t6 Check wheel suspension and attachment. t

11.1

4 D

E

94



Brakes W A B C





t



t



t



t



t

Travel W A B C

1 Test Deadman switch. t2 Checking bedding and attachment of the drive system. t3 Check transmission for noise and leakage. t4 Note: Replace transmission oil after 10000 service hours.


95

11.1

4 D

E

4.2.2 Optional equipment

Aquamatik


1 Check chassis and screw connections for damage. t2 Check doors and/or covers. t3 Check labels are legible and complete. t4 Test the operator platform and check for damage. t5 Check operator mat and steps are non-slip and damage-free. t


1Test "hydraulic" controls and make sure the labels are present, legible and complete.

t

2 Test lift cutout, check for damage and make sure it is secure. t3 Test lifting mechanism, check for wear, damage and test the settings. t

4Check cylinders and piston rods for damage and leaks, and make sure they are secure.

t

5 Test hydraulic system. t6 Replace hydraulic oil filter, ventilation/discharge filter. k t

7Check that hydraulic ports, hose and pipe lines are secure, check for leaks and damage.

t

8 Check hydraulic oil level and top up if necessary. t9 Test relief valve and adjust if necessary. t

10 Replace hydraulic oil. k t11 Check forks or load handler for wear and damage. t12 Check tie / plunger rods. t

Agreed performance levels W A B C

1Carry out a test run with rated load, if necessary with a customer-specific load.

t

2 Lubricate truck according to the lubrication schedule. t3 Demonstration after servicing. t

Steering W A B C

1 Test electric steering and its components. t2 Check mechanical parts of steering column. t


1Test Aquamatik plug, hose connections and float and check for leaks.

t

2 Test flow indicator and check for leaks. t

95

11.1

4 D

E4.2.2 Optional equipment

Aquamatik





t



t



t





t


Steering W A B C

1 Test electric steering and its components. t2 Check mechanical parts of steering column. t



t


11.1

4 D

E

96

Automatic crawl speed

Battery refill system

Data recorder

Entry skids / rollers

Electrolyte recirculation

Load backrest

Impact sensor

Lateral battery removal

Travel W A B C

1Check that sensors / switches are secured, not damaged, clean and operational.

t


1 Test battery refill system and check for leaks. t


1 Check data recorder is secure and check for damage. t


1Check entry skids or entry rollers for damage and wear, and test operation.

t


1 Replace air filter wadding. t2 Check hose connections and test the pump. t


1Check attachment is properly secured to the truck and the supporting elements.

t


1 Check impact sensor is secure and check for damage. t


1 Test battery lock / battery attachment. t

11.1

4 D

E

96



Data recorder



Load backrest

Impact sensor


Travel W A B C


t







t





t





97

11.1

4 D

EAccess module

Issued on: 19.04.2012 11:22:49


1 Test access module, check for damage and make sure it is secure. t

97

11.1

4 D

E

Access module

Issued on: 19.04.2012 11:22:49



11.1

4 D

E

98

5 Maintenance checklist ERE 225 folding platform

5.1 Proprietor


Brakes W A B C

1 Test brakes. t



t




t



t

Travel W A B C






Steering W A B C

1 Check tiller recuperating function. t

11.1

4 D

E

98

5 Maintenance checklist ERE 225 folding platform

5.1 Proprietor


Brakes W A B C

1 Test brakes. t



t




t



t

Travel W A B C






Steering W A B C

1 Check tiller recuperating function. t

99

11.1

4 D

E5.2 Customer Service


Brakes W A B C





t



t



t



t



t

Travel W A B C

1 Checking bedding and attachment of the drive system. t2 Check transmission for noise and leakage. t3 Note: Replace transmission oil after 10000 service hours.


99

11.1

4 D

E



Brakes W A B C





t



t



t



t



t

Travel W A B C

1 Checking bedding and attachment of the drive system. t2 Check transmission for noise and leakage. t3 Note: Replace transmission oil after 10000 service hours.


11.1

4 D

E

100


Aquamatik





t



t



t





t


Steering W A B C

1 Check tiller recuperating function. t2 Test electric steering and its components. t3 Check mechanical parts of steering column. t



t


11.1

4 D

E

100


Aquamatik





t



t



t





t


Steering W A B C

1 Check tiller recuperating function. t2 Test electric steering and its components. t3 Check mechanical parts of steering column. t



t


101

11.1

4 D

EAutomatic crawl speed


Data recorder



Load backrest

Impact sensor


Travel W A B C


t







t





t





101

11.1

4 D

E



Data recorder



Load backrest

Impact sensor


Travel W A B C


t







t





t





11.1

4 D

E

102

Access module

Issued on: 05.06.2012 14:31:05



11.1

4 D

E

102

Access module

Issued on: 05.06.2012 14:31:05



103

11.1

4 D

E6 Lubricants and Lubrication Schedule

6.1 Handling consumables safely

Handling consumables

Consumables must always be handled correctly. Follow the manufacturer’sinstructions.

WARNING!

Improper handling is hazardous to health, life and the environmentConsumables can be flammable.Keep consumables away from hot components and naked flames.Always keep consumables in prescribed containers.Always fill consumables in clean containers.Do not mix up different grades of consumable. The only exception to this is when

mixing is expressly stipulated in the operating instructions.

CAUTION!

Spilled liquids can cause slipping and endanger the environmentRisk of slipping from spilled liquids. The risk is greater when combined with water.Do not spill fluids.Spilled fluids must be removed immediately with an appropriate bonding agent.The bonding agent / consumable mixture must be disposed of in accordance with

regulations.

WARNING!

Oils (chain spray / hydraulic oil) are flammable and poisonous.Dispose of used oils in accordance with regulations. Store used oil safely until it can

be disposed of in accordance with regulations.Do not spill oil.Spilled fluids must be removed immediately with an appropriate bonding agent.The bonding agent / consumable mixture must be disposed of in accordance with

regulations.Observe national regulations when handling oils.Wear safety gloves when handling oils.Prevent oil from coming into contact with hot motor parts.Do not smoke when handling oil.Avoid contact and digestion. If you swallow oil do not induce vomiting but call for a

doctor immediately.Seek fresh air after breathing in oil fumes or vapours.If oil has come into contact with your skin, rinse your skin with water.If oil has come into contact with your eyes, rinse them with water and call for a

doctor immediately.Replace oil-soaked clothing and shoes immediately.

103

11.1

4 D

E

6 Lubricants and Lubrication Schedule

6.1 Handling consumables safely

Handling consumables

Consumables must always be handled correctly. Follow the manufacturer’sinstructions.

WARNING!

Improper handling is hazardous to health, life and the environmentConsumables can be flammable.Keep consumables away from hot components and naked flames.Always keep consumables in prescribed containers.Always fill consumables in clean containers.Do not mix up different grades of consumable. The only exception to this is when

mixing is expressly stipulated in the operating instructions.

CAUTION!

Spilled liquids can cause slipping and endanger the environmentRisk of slipping from spilled liquids. The risk is greater when combined with water.Do not spill fluids.Spilled fluids must be removed immediately with an appropriate bonding agent.The bonding agent / consumable mixture must be disposed of in accordance with

regulations.

WARNING!

Oils (chain spray / hydraulic oil) are flammable and poisonous.Dispose of used oils in accordance with regulations. Store used oil safely until it can

be disposed of in accordance with regulations.Do not spill oil.Spilled fluids must be removed immediately with an appropriate bonding agent.The bonding agent / consumable mixture must be disposed of in accordance with

regulations.Observe national regulations when handling oils.Wear safety gloves when handling oils.Prevent oil from coming into contact with hot motor parts.Do not smoke when handling oil.Avoid contact and digestion. If you swallow oil do not induce vomiting but call for a

doctor immediately.Seek fresh air after breathing in oil fumes or vapours.If oil has come into contact with your skin, rinse your skin with water.If oil has come into contact with your eyes, rinse them with water and call for a

doctor immediately.Replace oil-soaked clothing and shoes immediately.

11.1

4 D

E

104


CAUTION!


11.1

4 D

E

104


CAUTION!


105

11.1

4 D

E6.2 Lubrication Schedule

1 Compound ratio for cold store usage 1:1

Contact surfaces Cold Store Application

s Grease nipple Hydraulic oil filler neck

a Transmission oil drain plug

E

E

A0,7lA+C

1)

a

B 1,05 l

105

11.1

4 D

E

6.2 Lubrication Schedule

1 Compound ratio for cold store usage 1:1

Contact surfaces Cold Store Application

s Grease nipple Hydraulic oil filler neck

a Transmission oil drain plug

E

E

A0,7lA+C

1)

a

B 1,05 l

11.1

4 D

E

106

6.3 Consumables

*) also for cold store applications

Grease guidelines

Code Order no. Package quantity

Component Used for

A 50 449 669 5.0 l H-LPD 46, DIN 51524

Hydraulic System

B 50 380 904 5.0 l Fuchs Titan Cytrac HSY 75W-90 *)

transmission

C 29 200 810 5.0 l H-LP 10, DIN 51524

Hydraulic System

E 29 202 050 1.0 kg Grease, Polylube GA 352P

Lubrication

Code Saponification Dew point°C

Worked penetration at 25 °C

NLG1 class Application temperature °C

E Lithium >220 280 - 310 2 -35/+120

11.1

4 D

E

106

6.3 Consumables

*) also for cold store applications

Grease guidelines

Code Order no. Package quantity

Component Used for

A 50 449 669 5.0 l H-LPD 46, DIN 51524

Hydraulic System

B 50 380 904 5.0 l Fuchs Titan Cytrac HSY 75W-90 *)

transmission

C 29 200 810 5.0 l H-LP 10, DIN 51524

Hydraulic System

E 29 202 050 1.0 kg Grease, Polylube GA 352P

Lubrication

Code Saponification Dew point°C

Worked penetration at 25 °C

NLG1 class Application temperature °C

E Lithium >220 280 - 310 2 -35/+120

107

11.1

4 D

E7 Maintenance and repairs

7.1 Preparing the truck for maintenance and repairs

All necessary safety measures must be taken to avoid accidents when carrying outmaintenance and repairs. The following preparations must be made:

Procedure• Park the truck on a level surface.• Fully lower the main and auxiliary lift.• Park the truck securely, (see "Parking the truck securely" on page 49).• Disconnect the battery to prevent the truck from being switched on accidentally.• When working under a raised lift truck, secure it to prevent it from lowering, tipping

or sliding away.

WARNING!

Risk of accidents when working under the load handler, driver's cab and lifttruckWhen working under a raised load handler, driver's cab or a raised truck, secure

them to prevent the truck from from lowering, tipping or sliding away.When raising the truck, follow the instructions, (see "Transport and

Commissioning" on page 29). When working on the parking brake, prevent thetruck from accidentally rolling away (e.g. with wedges).

107

11.1

4 D

E

7 Maintenance and repairs

7.1 Preparing the truck for maintenance and repairs

All necessary safety measures must be taken to avoid accidents when carrying outmaintenance and repairs. The following preparations must be made:

Procedure• Park the truck on a level surface.• Fully lower the main and auxiliary lift.• Park the truck securely, (see "Parking the truck securely" on page 49).• Disconnect the battery to prevent the truck from being switched on accidentally.• When working under a raised lift truck, secure it to prevent it from lowering, tipping

or sliding away.

WARNING!

Risk of accidents when working under the load handler, driver's cab and lifttruckWhen working under a raised load handler, driver's cab or a raised truck, secure

them to prevent the truck from from lowering, tipping or sliding away.When raising the truck, follow the instructions, (see "Transport and

Commissioning" on page 29). When working on the parking brake, prevent thetruck from accidentally rolling away (e.g. with wedges).

11.1

4 D

E

108

7.2 Replacing the drive wheel

Z The drive wheel must only be replaced by authorised service personnel.

7.3 Checking the hydraulic oil level

Check oil level

Requirements– Lower the load handler.– Prepare the truck for maintenance

and repairs, (see "Preparing thetruck for maintenance and repairs"on page 107).

– Open the battery panel, (see"Exposing the battery" on page 36).

– Lift off the front cover, (see"Removing the front panel" onpage 108)

Procedure• Check oil level on hydraulic reservoir (73).

Z The hydraulic oil level in the tank should be between the "Max" and "Min" markswith the load handler lowered.

• If necessary add hydraulic oil of the correct grade, (see "Consumables" onpage 106) (see also table).

Oil level is checked.

7.4 Removing the front panel

Remove the front cover (industrial truck with folding standing platform)

Requirements– Open the battery panel, (see "Exposing the battery" on page 36).

Procedure• Fold down the standing platform (8).• Carefully lift up the dashboard (74) at all four corners and remove it from the

industrial truck.• Pull the front cover (54) out of its bracket using the grip shells and then pull it up out

of the bottom retainers.

The front panel is now disassembled.

Z Assembly is the reverse order.

Remove the front cover (industrial truck with fixed standing platform)


min

max

73

11.1

4 D

E

108

7.2 Replacing the drive wheel

Z The drive wheel must only be replaced by authorised service personnel.

7.3 Checking the hydraulic oil level

Check oil level

Requirements– Lower the load handler.– Prepare the truck for maintenance

and repairs, (see "Preparing thetruck for maintenance and repairs"on page 107).

– Open the battery panel, (see"Exposing the battery" on page 36).

– Lift off the front cover, (see"Removing the front panel" onpage 108)

Procedure• Check oil level on hydraulic reservoir (73).

Z The hydraulic oil level in the tank should be between the "Max" and "Min" markswith the load handler lowered.

• If necessary add hydraulic oil of the correct grade, (see "Consumables" onpage 106) (see also table).

Oil level is checked.

7.4 Removing the front panel

Remove the front cover (industrial truck with folding standing platform)


Procedure• Fold down the standing platform (8).• Carefully lift up the dashboard (74) at all four corners and remove it from the





Remove the front cover (industrial truck with fixed standing platform)


min

max

73

109

11.1

4 D

EProcedure• Carefully lift up the dashboard (74) at all four corners and remove it from the





54

74

109

11.1

4 D

E

Procedure• Carefully lift up the dashboard (74) at all four corners and remove it from the





54

74

11.1

4 D

E

110

7.5 Checking electrical fuses

Check fuses

Requirements– Truck prepared for maintenance and repairs, (see "Preparing the truck for

maintenance and repairs" on page 107).– Front cover removed, (see "Removing the front panel" on page 108).

Procedure• Check the fuse ratings against the table and replace if necessary.

The fuses are now checked.

Traction controller AS2412i fuses


Item Component To protect Rating (A)75 2F1 Lift motor 15076 1F1 Drive motor 30077 3F1 Steering auxiliary motor fuse 3078 F1 Overall fuse 1079 9F21 Electric/mechanical components 380 6F1 Battery discharge indicator / battery hour meter 2

79

7778

80

7675

11.1

4 D

E

110

7.5 Checking electrical fuses

Check fuses

Requirements– Truck prepared for maintenance and repairs, (see "Preparing the truck for

maintenance and repairs" on page 107).– Front cover removed, (see "Removing the front panel" on page 108).

Procedure• Check the fuse ratings against the table and replace if necessary.

The fuses are now checked.



Item Component To protect Rating (A)75 2F1 Lift motor 15076 1F1 Drive motor 30077 3F1 Steering auxiliary motor fuse 3078 F1 Overall fuse 1079 9F21 Electric/mechanical components 380 6F1 Battery discharge indicator / battery hour meter 2

79

7778

80

7675

111

11.1

4 D

ECombi controller AS2412iS fuses

Combi controller AS2412iS fuses

Item Component To protect Rating (A)89 F17 Radio data transmission (o) 1078 F1 Overall control circuit fuse 1077 9F22 Sensor system fuse 1080 6F1 Battery Discharge Indicator 276 1F1 Drive / lift motor 300

76

78

77

80

89

111

11.1

4 D

E



Item Component To protect Rating (A)89 F17 Radio data transmission (o) 1078 F1 Overall control circuit fuse 1077 9F22 Sensor system fuse 1080 6F1 Battery Discharge Indicator 276 1F1 Drive / lift motor 300

76

78

77

80

89

11.1

4 D

E

112

7.6 Restoring the truck to service after maintenance and repairs

Procedure• Thoroughly clean the truck.• Lubricate the truck according to the lubrication schedule, (see "Lubrication

Schedule" on page 105).• Clean the battery, grease the terminals and connect the battery.• Charge the battery, (see "Charging the battery" on page 37).• Check the transmission oil for condensation water and replace if necessary.• Check the hydraulic oil for condensation water and replace if necessary.

Z The manufacturer's customer service department is specially trained to carry outthese operations.

WARNING!Faulty brakes can cause accidentsAs soon as the truck has been started, test the brakes several times.Report any defects immediately to your supervisor.Tag out and decommission the faulty industrial truck.Only return the truck to service when you have identified and rectified the fault.

• Start up the truck, (see "Starting up the truck" on page 47).Z If there are switching problems in the electrical system, apply contact spray to the

exposed contacts and remove any oxide layers on the contacts of the controls byapplying them repeatedly.

11.1

4 D

E

112

7.6 Restoring the truck to service after maintenance and repairs







113

11.1

4 D

E8 Safety tests to be performed at intervals and after unusual

incidents

Z Perform a safety check in accordance with national regulations. Jungheinrichrecommends the truck be checked to FEM guideline 4.004. The Jungheinrichsafety department has trained personnel who are able to carry out inspections.

The truck must be inspected at least annually or after any unusual event by a qualifiedinspector (be sure to comply with national regulations). The inspector shall assess thecondition of the truck from purely a safety viewpoint, without regard to operational oreconomic circumstances. The inspector shall be sufficiently instructed andexperienced to be able to assess the condition of the truck and the effectiveness ofthe safety mechanisms based on the technical regulations and principles governingthe inspection of forklift trucks.

A thorough test of the truck must be undertaken with regard to its technical conditionfrom a safety aspect. The truck must also be examined for damage caused bypossible improper use. A test report shall be provided. The test results must be keptfor at least the next 2 inspections.

The owner is responsible for ensuring that faults are rectified immediately.

Z A test plate is attached to the truck as proof that it has passed the safety inspection.This plate indicates the due date for the next inspection.

113

11.1

4 D

E

8 Safety tests to be performed at intervals and after unusual incidents

Z Perform a safety check in accordance with national regulations. Jungheinrichrecommends the truck be checked to FEM guideline 4.004. The Jungheinrichsafety department has trained personnel who are able to carry out inspections.

The truck must be inspected at least annually or after any unusual event by a qualifiedinspector (be sure to comply with national regulations). The inspector shall assess thecondition of the truck from purely a safety viewpoint, without regard to operational oreconomic circumstances. The inspector shall be sufficiently instructed andexperienced to be able to assess the condition of the truck and the effectiveness ofthe safety mechanisms based on the technical regulations and principles governingthe inspection of forklift trucks.

A thorough test of the truck must be undertaken with regard to its technical conditionfrom a safety aspect. The truck must also be examined for damage caused bypossible improper use. A test report shall be provided. The test results must be keptfor at least the next 2 inspections.

The owner is responsible for ensuring that faults are rectified immediately.

Z A test plate is attached to the truck as proof that it has passed the safety inspection.This plate indicates the due date for the next inspection.

11.1

4 D

E

114

9 Decommissioning the industrial truck

Z If the truck is to be out of service for more than a month, e.g. for commercialreasons, it must be stored in a frost-free and dry room. All necessary measuresmust be taken before, during and after decommissioning as described hereafter.

WARNING!

Lifting and jacking up the truck safelyIn order to raise the truck, the lifting gear must only be secured to the points speciallyprovided for this purpose. You may only work under a raised load handler if it has been secured with asufficiently strong chain or the fastening bolt.In order to raise and jack up the truck safely, proceed as follows:Jack up the truck only on a level surface and prevent it from moving accidentally.Always use a jack with sufficient capacity. When jacking up the truck, take




When the truck is out of service it must be jacked up so that all the wheels are clearof the ground. This is the only way of ensuring that the wheels and wheel bearingsare not damaged.

If the truck is to be out of service for more than 6 months, agree further measures withthe manufacturer's customer service department.

9.1 Before taking the truck out of service

Procedure• Thoroughly clean the truck.


• Test the brakes.• Check the hydraulic oil level and replenish if necessary, (see "Checking the

hydraulic oil level" on page 108).• Apply a thin layer of oil or grease to any non-painted mechanical components.• Lubricate the truck according to the lubrication schedule, (see "Lubrication

Schedule" on page 105).• Charge the battery, (see "Charging the battery" on page 37).• Disconnect the battery, clean it and grease the terminals.

11.1

4 D

E

114

9 Decommissioning the industrial truck

Z If the truck is to be out of service for more than a month, e.g. for commercialreasons, it must be stored in a frost-free and dry room. All necessary measuresmust be taken before, during and after decommissioning as described hereafter.

WARNING!

Lifting and jacking up the truck safelyIn order to raise the truck, the lifting gear must only be secured to the points speciallyprovided for this purpose. You may only work under a raised load handler if it has been secured with asufficiently strong chain or the fastening bolt.In order to raise and jack up the truck safely, proceed as follows:Jack up the truck only on a level surface and prevent it from moving accidentally.Always use a jack with sufficient capacity. When jacking up the truck, take




When the truck is out of service it must be jacked up so that all the wheels are clearof the ground. This is the only way of ensuring that the wheels and wheel bearingsare not damaged.

If the truck is to be out of service for more than 6 months, agree further measures withthe manufacturer's customer service department.

9.1 Before taking the truck out of service

Procedure• Thoroughly clean the truck.


• Test the brakes.• Check the hydraulic oil level and replenish if necessary, (see "Checking the

hydraulic oil level" on page 108).• Apply a thin layer of oil or grease to any non-painted mechanical components.• Lubricate the truck according to the lubrication schedule, (see "Lubrication

Schedule" on page 105).• Charge the battery, (see "Charging the battery" on page 37).• Disconnect the battery, clean it and grease the terminals.

115

11.1

4 D

EZ In addition, follow the battery manufacturer’s instructions.

• Spay all exposed electrical contacts with a suitable contact spray.

9.2 Action to be taken during decommissioning

NOTE

Full discharge can damage the batterySelf-discharge can cause the battery to fully discharge. Full discharge shortens theuseful life of the battery. Charge the battery at least every 2 months.

Z Charge the battery, (see "Charging the battery" on page 37).

115

11.1

4 D

E

Z In addition, follow the battery manufacturer’s instructions.• Spay all exposed electrical contacts with a suitable contact spray.

9.2 Action to be taken during decommissioning

NOTE

Full discharge can damage the batterySelf-discharge can cause the battery to fully discharge. Full discharge shortens theuseful life of the battery. Charge the battery at least every 2 months.

Z Charge the battery, (see "Charging the battery" on page 37).

11.1

4 D

E

116

9.3 Restoring the truck to service after decommissioning







10 Final de-commissioning, disposal

Z Final de-commissioning or disposal of the truck in must be performed inaccordance with the regulations of the country of use. In particular, regulationsgoverning the disposal of batteries, fuels and electronic and electrical systemsmust be observed.

The truck must only be disassembled by trained personnel in accordance with theprocedures as specified by the manufacturer. Note the manufacturer’s safetyinstructions as specified in the service documentation.

11.1

4 D

E

116

9.3 Restoring the truck to service after decommissioning







10 Final de-commissioning, disposal

Z Final de-commissioning or disposal of the truck in must be performed inaccordance with the regulations of the country of use. In particular, regulationsgoverning the disposal of batteries, fuels and electronic and electrical systemsmust be observed.

The truck must only be disassembled by trained personnel in accordance with theprocedures as specified by the manufacturer. Note the manufacturer’s safetyinstructions as specified in the service documentation.

117

11.1

4 D

E11 Human vibration measurement

Z Vibrations that affect the driver during operation over the course of the day areknown as human vibrations. Excessive human vibrations will cause the driver longterm health problems. The European "2002/44/EC/Vibration" operator directive hastherefore been established to protect drivers. To help operators to assess the application situation, the manufacturer offers aservice of measuring these human vibrations.

117

11.1

4 D

E

11 Human vibration measurement

Z Vibrations that affect the driver during operation over the course of the day areknown as human vibrations. Excessive human vibrations will cause the driver longterm health problems. The European "2002/44/EC/Vibration" operator directive hastherefore been established to protect drivers. To help operators to assess the application situation, the manufacturer offers aservice of measuring these human vibrations.

1

03.1

3 E

N

A Traction Battery Appendix

Contents

A Traction Battery Appendix....................................................... 1

1 Correct Use and Application.................................................................... 22 Data plate ................................................................................................ 23 Safety Instructions, Warning Indications and other Notes....................... 34 Lead acid batteries with armour plated cells and liquid electrolyte.......... 44.1 Description............................................................................................... 44.2 Operation................................................................................................. 54.3 Servicing lead-acid batteries with armour plated cells............................. 85 PzV and PzV-BS lead-acid batteries with sealed armour plated cells..... 95.1 Description............................................................................................... 95.2 Operation................................................................................................. 105.3 Servicing PzV and PzV-BS lead-acid batteries with sealed armour plated

cells ......................................................................................................... 136 Aquamatik water replenishment system.................................................. 146.1 Water replenishment system design ....................................................... 146.2 Functional Description ............................................................................. 156.3 Adding water............................................................................................ 156.4 Water pressure ........................................................................................ 156.5 Filling time ............................................................................................... 166.6 Water quality............................................................................................ 166.7 Battery tubing .......................................................................................... 166.8 Operating temperature ............................................................................ 166.9 Cleaning measures.................................................................................. 176.10 Service mobile vehicle............................................................................. 177 Electrolyte circulation............................................................................... 187.1 Functional Description ............................................................................. 188 Cleaning batteries.................................................................................... 209 Storing the battery ................................................................................... 2210 Troubleshooting....................................................................................... 2211 Disposal................................................................................................... 22

1

03.1

3 E

N

A Traction Battery Appendix

Contents

A Traction Battery Appendix....................................................... 1

1 Correct Use and Application.................................................................... 22 Data plate ................................................................................................ 23 Safety Instructions, Warning Indications and other Notes....................... 34 Lead acid batteries with armour plated cells and liquid electrolyte.......... 44.1 Description............................................................................................... 44.2 Operation................................................................................................. 54.3 Servicing lead-acid batteries with armour plated cells............................. 85 PzV and PzV-BS lead-acid batteries with sealed armour plated cells..... 95.1 Description............................................................................................... 95.2 Operation................................................................................................. 105.3 Servicing PzV and PzV-BS lead-acid batteries with sealed armour plated

cells ......................................................................................................... 136 Aquamatik water replenishment system.................................................. 146.1 Water replenishment system design ....................................................... 146.2 Functional Description ............................................................................. 156.3 Adding water............................................................................................ 156.4 Water pressure ........................................................................................ 156.5 Filling time ............................................................................................... 166.6 Water quality............................................................................................ 166.7 Battery tubing .......................................................................................... 166.8 Operating temperature ............................................................................ 166.9 Cleaning measures.................................................................................. 176.10 Service mobile vehicle............................................................................. 177 Electrolyte circulation............................................................................... 187.1 Functional Description ............................................................................. 188 Cleaning batteries.................................................................................... 209 Storing the battery ................................................................................... 2210 Troubleshooting....................................................................................... 2211 Disposal................................................................................................... 22

03.1

3 E

N

2

1 Correct Use and Application

Failure to observe the operating instructions, carrying out repairs with non-originalspare parts, tampering with the battery or using electrolyte additives will invalidate thewarranty.

Observe the instructions for maintaining the safety rating during operation forbatteries in accordance with Ex I and Ex II (see relevant certification).

2 Data plate

1,2

4

8

10

11

6

3

5

9

7

12 13

14

15

1 Battery name2 Battery type3 Production week/year manf.4 Serial number5 Supplier number6 Rated voltage7 Rated capacity9 Battery weight in kg8 Number of cells15 Electrolyte volume in litres10 Battery number11 Manufacturer13 Manufacturer's logo12 CE mark only for batteries beyond 75 volts14 Safety instructions and warning information

03.1

3 E

N

2

1 Correct Use and Application

Failure to observe the operating instructions, carrying out repairs with non-originalspare parts, tampering with the battery or using electrolyte additives will invalidate thewarranty.

Observe the instructions for maintaining the safety rating during operation forbatteries in accordance with Ex I and Ex II (see relevant certification).

2 Data plate

1,2

4

8

10

11

6

3

5

9

7

12 13

14

15

1 Battery name2 Battery type3 Production week/year manf.4 Serial number5 Supplier number6 Rated voltage7 Rated capacity9 Battery weight in kg8 Number of cells15 Electrolyte volume in litres10 Battery number11 Manufacturer13 Manufacturer's logo12 CE mark only for batteries beyond 75 volts14 Safety instructions and warning information

3

03.1

3 E

N3 Safety Instructions, Warning Indications and other Notes

Used batteries must be treated as hazardous waste.

These batteries are marked with the recycling symbol and the sign showing a crossed-out rubbish bin, and should not be disposed of with ordinary household waste. waste.

Buy-back terms and type of recycling are to be agreed with the manufacturer as described in § 8 of the battery legislation.

Do not smoke!

No naked flames, glowing embers or sparks near the battery - fire and explosion hazard!

Avoid fire and explosion hazards and short circuits due to overheating!

Keep away from naked flames and strong heat sources.

Always wear protective clothing (e.g. safety goggles and safety gloves) when working on cells and batteries. batteries. Always wash your hands after completing the work. Use insulated tools only. Do not physically alter the battery, strike, crush, compress, notch, dent or modify it in any way. Hazardous electric voltage! The metal parts of the battery cells are permanently live. Therefore do not place any foreign objects or tools on the battery.Observe national health and safety regulations.

If the materials leak, do not inhale the fumes. Wear safety gloves.

Follow the user instructions and keep them in a visible position in the charging area.

Work on the batteries should be performed only as instructed by specialist personnel.

3

03.1

3 E

N

3 Safety Instructions, Warning Indications and other Notes

Used batteries must be treated as hazardous waste.

These batteries are marked with the recycling symbol and the sign showing a crossed-out rubbish bin, and should not be disposed of with ordinary household waste. waste.

Buy-back terms and type of recycling are to be agreed with the manufacturer as described in § 8 of the battery legislation.

Do not smoke!

No naked flames, glowing embers or sparks near the battery - fire and explosion hazard!

Avoid fire and explosion hazards and short circuits due to overheating!

Keep away from naked flames and strong heat sources.

Always wear protective clothing (e.g. safety goggles and safety gloves) when working on cells and batteries. batteries. Always wash your hands after completing the work. Use insulated tools only. Do not physically alter the battery, strike, crush, compress, notch, dent or modify it in any way. Hazardous electric voltage! The metal parts of the battery cells are permanently live. Therefore do not place any foreign objects or tools on the battery.Observe national health and safety regulations.

If the materials leak, do not inhale the fumes. Wear safety gloves.

Follow the user instructions and keep them in a visible position in the charging area.

Work on the batteries should be performed only as instructed by specialist personnel.

03.1

3 E

N

4

4 Lead acid batteries with armour plated cells and liquid electrolyte

4.1 Description

Jungheinrich traction batteries are lead acid batteries with armour plated cells andliquid electrolyte. The names of the traction batteries are PzS, PzB, PzS Lib and PzM.

Electrolyte

The rated density of the electrolyte assumes a temperature of 30°C and the ratedelectrolyte level is fully charged. Higher temperatures will reduce, lower temperatureswill increase the electrolyte density. The adjustment factor is ± 0.0007 kg/l per K, e.g.electrolyte density 1.28 kg/l at 45°C corresponds to a density of 1.29 kg/l at 30°C.

The electrolyte must conform to DIN 43530 Part 2 purity regulations.

4.1.1 Battery nominal data

1. Product Traction battery

2. Nominal voltage 2.0 V x no. of cells

3. Rated capacity C5 See data plate

4. Discharge current C5/5h

5. Nominal electrolyte density1

1. Reached within the first 10 cycles.

1.29 kg/l

6. Nominal temperature2

2. Higher temperatures shorten the useful life, lower temperatures reduce the available capacity.

30 °C

7. System rated electrolyte level up to "Max" electrolyte level marking

Limit temperature3

3. Not permissible as operating temperature.

55°C

03.1

3 E

N

4

4 Lead acid batteries with armour plated cells and liquid electrolyte

4.1 Description

Jungheinrich traction batteries are lead acid batteries with armour plated cells andliquid electrolyte. The names of the traction batteries are PzS, PzB, PzS Lib and PzM.

Electrolyte

The rated density of the electrolyte assumes a temperature of 30°C and the ratedelectrolyte level is fully charged. Higher temperatures will reduce, lower temperatureswill increase the electrolyte density. The adjustment factor is ± 0.0007 kg/l per K, e.g.electrolyte density 1.28 kg/l at 45°C corresponds to a density of 1.29 kg/l at 30°C.

The electrolyte must conform to DIN 43530 Part 2 purity regulations.






5. Nominal electrolyte density1

1. Reached within the first 10 cycles.

1.29 kg/l

6. Nominal temperature2


30 °C

7. System rated electrolyte level up to "Max" electrolyte level marking

Limit temperature3

3. Not permissible as operating temperature.

55°C

5

03.1

3 E

N4.2 Operation

4.2.1 Commissioning unfilled batteries

Z The operations required must be carried out by the manufacturer's customerservice department or a customer service organisation authorised by themanufacturer.

4.2.2 Commissioning filled and charged batteries

Checks and operations to be performed before starting daily work

Procedure• Make sure the battery is in physically good condition. • Make sure the terminals are correct (positive to positive and negative to negative)

and check that contacts on the battery terminal conducting system are secure.• Check the terminal screw torques (M10 = 23 ±1 Nm) of the terminal conductors and

connectors. • Charge up the battery.• Check the electrolyte level.

Z The electrolyte level must be above the cell baffle or the top of the separator.• Add electrolyte with distilled water up to the nominal level.

Checks completed.

4.2.3 Discharging the battery

Z To achieve an optimum useful life avoid operational discharge of more than 80% ofnominal capacity (full discharge). This corresponds to a minimum electrolytedensity of 1.13 kg/l at the end of the discharge. Recharge a discharged batteryimmediately.

5

03.1

3 E

N

4.2 Operation

4.2.1 Commissioning unfilled batteries


4.2.2 Commissioning filled and charged batteries




connectors. • Charge up the battery.• Check the electrolyte level.

Z The electrolyte level must be above the cell baffle or the top of the separator.• Add electrolyte with distilled water up to the nominal level.

Checks completed.


Z To achieve an optimum useful life avoid operational discharge of more than 80% ofnominal capacity (full discharge). This corresponds to a minimum electrolytedensity of 1.13 kg/l at the end of the discharge. Recharge a discharged batteryimmediately.

03.1

3 E

N

6

4.2.4 Charging the battery

WARNING!

The gases produced during charging can cause explosionsThe battery gives off a mixture of oxygen and hydrogen (electrolytic gas) duringcharging. Gassing is a chemical process. This gas mixture is highly explosive andmust not be ignited.Always disconnect the charger and truck before connecting or disconnecting the

charger and battery.The charger must be adapted to the battery in terms of voltage, charge capacity

and battery technology.Before charging, check all cables and plug connections for visible signs of damage.Ventilate the room in which the truck is being charged.Battery cell surfaces must remain exposed during charging in order to ensure

sufficient ventilation, see truck operating instructions, chapter D, Charging theBattery.

Do not smoke and avoid naked flames when handling batteries.Wherever an industrial truck is parked for charging there must be no inflammable

material or consumables capable of creating sparks within a minimum distance of2 m from the truck.

Fire protection equipment must be available.Do not place any metallic objects on the battery.Always follow the safety regulations of the battery and charger station

manufacturers.

NOTE

The battery must only be charged with DC current. All charging processes inaccordance with DIN 41773 and DIN 41774 are permissible.

03.1

3 E

N

6


WARNING!








manufacturers.

NOTE

The battery must only be charged with DC current. All charging processes inaccordance with DIN 41773 and DIN 41774 are permissible.

7

03.1

3 E

N

Z The electrolyte temperature rises by approx. 10 K during charging. Charging shouldtherefore only begin when the electrolyte temperature is below 45°C. Theelectrolyte temperature of batteries must be at least +10°C before charging.Otherwise the battery will not charge correctly. Below 10°C the battery isinsufficiently charged with standard charging systems.

Charging the battery

Requirements– Electrolyte temperature min. 10°C to max. 45°C

Procedure• Open or take off the tray lid or covers from the battery compartment.

Z Deviations are outlined in the truck's operating instructions. The plugs remain onthe cells or remain closed.

• Connect the battery to the switched off charger, ensuring the terminals are connect(positive to positive and negative to negative).

• Switch on the charger.

Battery charged

Z Charging is considered to be complete when the electrolyte density and batteryvoltage remain constant for more than 2 hours.

Compensation charging

Compensation charging is used to ensure the useful life and maintain capacity afterfull discharge and repeated insufficient charging. The maximum compensationcharge current is 5 A/100 Ah rated capacity.

Z Compensation charging should be carried out weekly.

Trickle charging

Battery trickle charging is partial charging that extends the daily application time.Higher average temperatures occur during trickle charging which reduce the usefullife of the batteries.

Z Trickle charges should only be performed when the charge level is below 60 %. Usereplacement batteries instead of regular trickle charging.

7

03.1

3 E

N

Z The electrolyte temperature rises by approx. 10 K during charging. Charging shouldtherefore only begin when the electrolyte temperature is below 45°C. Theelectrolyte temperature of batteries must be at least +10°C before charging.Otherwise the battery will not charge correctly. Below 10°C the battery isinsufficiently charged with standard charging systems.


Requirements– Electrolyte temperature min. 10°C to max. 45°C

Procedure• Open or take off the tray lid or covers from the battery compartment.

Z Deviations are outlined in the truck's operating instructions. The plugs remain onthe cells or remain closed.

• Connect the battery to the switched off charger, ensuring the terminals are connect(positive to positive and negative to negative).

• Switch on the charger.

Battery charged



Compensation charging is used to ensure the useful life and maintain capacity afterfull discharge and repeated insufficient charging. The maximum compensationcharge current is 5 A/100 Ah rated capacity.


Trickle charging

Battery trickle charging is partial charging that extends the daily application time.Higher average temperatures occur during trickle charging which reduce the usefullife of the batteries.

Z Trickle charges should only be performed when the charge level is below 60 %. Usereplacement batteries instead of regular trickle charging.

03.1

3 E

N

8

4.3 Servicing lead-acid batteries with armour plated cells

Water quality

Z The quality of the water used to fill up electrolyte must correspond to purified ordistilled water. Purified water can be produced through distillation or ionexchangers and is then suitable for the production of electrolyte.

4.3.1 Daily

– Charge the battery after each discharge.– After charging, check the electrolyte level.– If necessary, add purified water up to the rated level after charging.

Z The height of the electrolyte level should not be below the cell baffle or above thetop of the separator, or the "Min" and "Max" electrolyte markings respectively.

4.3.2 Weekly

– After re-charging, carry out a visual inspection for dirt and physical damage.– If the battery is charged regularly according to the IU characteristic, carry out a

compensation charge.

4.3.3 Monthly

– Towards the end of the charging process measure and record the voltages of allthe cells with the charger switched on.

– After charging measure and record the electrolyte density and the electrolytetemperature in all the cells.

– Compare the results with the previous ones.

Z If you find significant differences compared with the previous measurements ordifferences between the cells, contact the manufacturer's customer servicedepartment.

4.3.4 Annually

– Measure the truck insulation resistance in accordance with EN 1175-1.– Measure the battery insulation resistance in accordance with EN 1987-1.

Z In accordance with DIN EN 50272-3 the battery insulation resistance should not beless than 50 Ω per volt of rated voltage.

03.1

3 E

N

8

4.3 Servicing lead-acid batteries with armour plated cells

Water quality


4.3.1 Daily

– Charge the battery after each discharge.– After charging, check the electrolyte level.– If necessary, add purified water up to the rated level after charging.

Z The height of the electrolyte level should not be below the cell baffle or above thetop of the separator, or the "Min" and "Max" electrolyte markings respectively.

4.3.2 Weekly

– After re-charging, carry out a visual inspection for dirt and physical damage.– If the battery is charged regularly according to the IU characteristic, carry out a

compensation charge.

4.3.3 Monthly

– Towards the end of the charging process measure and record the voltages of allthe cells with the charger switched on.

– After charging measure and record the electrolyte density and the electrolytetemperature in all the cells.

– Compare the results with the previous ones.


4.3.4 Annually



9

03.1

3 E

N5 PzV and PzV-BS lead-acid batteries with sealed armour

plated cells

5.1 Description

PzV batteries are sealed batteries with fixed electrolytes, to which no water can beadded over the entire lifespan of the battery. Relief valves are used as plugs whichare destroyed when opened. During operation the same safety requirements apply tothe sealed batteries as for batteries with liquid electrolyte. This is to avoid electricshock, explosion of the electrolyte charging gases or hazardous electrolyte burns ifthe cell vessels are destroyed.

Z PzV batteries are low gassing, but not gassing-free.

Electrolyte

The electrolyte is sulphuric acid which is fixed in gel. The density of the electrolytecannot be measured.






5. Rated temperature 30 °C

Limit temperature1


45°C, not permissible as operating temperature.

6. Rated density of the electrolyte Cannot be measured

7. System rated electrolyte level Cannot be measured

9

03.1

3 E

N

5 PzV and PzV-BS lead-acid batteries with sealed armour plated cells

5.1 Description

PzV batteries are sealed batteries with fixed electrolytes, to which no water can beadded over the entire lifespan of the battery. Relief valves are used as plugs whichare destroyed when opened. During operation the same safety requirements apply tothe sealed batteries as for batteries with liquid electrolyte. This is to avoid electricshock, explosion of the electrolyte charging gases or hazardous electrolyte burns ifthe cell vessels are destroyed.

Z PzV batteries are low gassing, but not gassing-free.

Electrolyte

The electrolyte is sulphuric acid which is fixed in gel. The density of the electrolytecannot be measured.






5. Rated temperature 30 °C

Limit temperature1


45°C, not permissible as operating temperature.

6. Rated density of the electrolyte Cannot be measured

7. System rated electrolyte level Cannot be measured

03.1

3 E

N

10

5.2 Operation

5.2.1 Commissioning




connectors. • Re-charge the battery.• Charge the battery.

Check completed.


Z To achieve an optimum useful life avoid operational discharges of more than 60%of nominal capacity.

Z If the battery is discharged during operation by more than 80% of rated capacity theuseful life of the battery will reduce significantly. Fully or partially dischargedbatteries must be re-charged immediately and not left unattended.


WARNING!








manufacturers.

03.1

3 E

N

10

5.2 Operation

5.2.1 Commissioning




connectors. • Re-charge the battery.• Charge the battery.

Check completed.


Z To achieve an optimum useful life avoid operational discharges of more than 60%of nominal capacity.

Z If the battery is discharged during operation by more than 80% of rated capacity theuseful life of the battery will reduce significantly. Fully or partially dischargedbatteries must be re-charged immediately and not left unattended.


WARNING!








manufacturers.

11

03.1

3 E

N

NOTE

Charging the battery incorrectly can result in material damage.Incorrect battery charging can result in overloading of the electric wires and contacts,hazardous gas formation and electrolyte leakage from the cells.Always charge the battery with DC current.All DIN 41773 charging procedures are permitted in the format approved by the

manufacturer.Always connect the battery to a charger that is appropriate to the size and type of

the battery.If necessary have the charger checked by the manufacturer's customer service

department for suitability.Do not exceed limit currents in the gassing area in accordance with DIN EN 50272-

3.

11

03.1

3 E

N

NOTE

Charging the battery incorrectly can result in material damage.Incorrect battery charging can result in overloading of the electric wires and contacts,hazardous gas formation and electrolyte leakage from the cells.Always charge the battery with DC current.All DIN 41773 charging procedures are permitted in the format approved by the

manufacturer.Always connect the battery to a charger that is appropriate to the size and type of

the battery.If necessary have the charger checked by the manufacturer's customer service

department for suitability.Do not exceed limit currents in the gassing area in accordance with DIN EN 50272-

3.

03.1

3 E

N

12


Requirements– Electrolyte temperature between +15°C and 35°C

Procedure• Open or take off the tray lid or covers from the battery compartment.• Connect the battery to the switched off charger, ensuring the terminals are connect

(positive to positive and negative to negative). • Switch on the charger.

Z The electrolyte temperature rises by approx. 10 K during charging. If thetemperatures are permanently higher than 40°C or lower than 15°C, a temperature-dependent constant voltage control of the charger is required. The adjustmentfactor must be applied with -0.004 V/C per K.

Battery charged



Compensation charging is used to ensure the useful life and maintain capacity afterfull discharge and repeated insufficient charging.


Trickle charging

Battery trickle charging is partial charging that extends the daily application time.Higher average temperatures occur during trickle charging which can reduce theuseful life of the batteries.

Z Trickle charges should only be performed when the charge level is below 50%. Usereplacement batteries instead of regular trickle charging.

Z Avoid trickle charging with PzV batteries.

03.1

3 E

N

12


Requirements– Electrolyte temperature between +15°C and 35°C

Procedure• Open or take off the tray lid or covers from the battery compartment.• Connect the battery to the switched off charger, ensuring the terminals are connect

(positive to positive and negative to negative). • Switch on the charger.

Z The electrolyte temperature rises by approx. 10 K during charging. If thetemperatures are permanently higher than 40°C or lower than 15°C, a temperature-dependent constant voltage control of the charger is required. The adjustmentfactor must be applied with -0.004 V/C per K.

Battery charged



Compensation charging is used to ensure the useful life and maintain capacity afterfull discharge and repeated insufficient charging.


Trickle charging

Battery trickle charging is partial charging that extends the daily application time.Higher average temperatures occur during trickle charging which can reduce theuseful life of the batteries.

Z Trickle charges should only be performed when the charge level is below 50%. Usereplacement batteries instead of regular trickle charging.

Z Avoid trickle charging with PzV batteries.

13

03.1

3 E

N5.3 Servicing PzV and PzV-BS lead-acid batteries with sealed armour

plated cells

Z Do not add water!

5.3.1 Daily

– Charge the battery after each discharge.

5.3.2 Weekly

– Visually inspect for dirt and physical damage.

5.3.3 Every three months

– Measure and record the overall voltage.– Measure and record the individual voltages.– Compare the results with the previous ones.

Z Carry out the measurements after full charging and subsequent resting for at least5 hours.


5.3.4 Annually



13

03.1

3 E

N

5.3 Servicing PzV and PzV-BS lead-acid batteries with sealed armour plated cells

Z Do not add water!

5.3.1 Daily

– Charge the battery after each discharge.

5.3.2 Weekly

– Visually inspect for dirt and physical damage.

5.3.3 Every three months

– Measure and record the overall voltage.– Measure and record the individual voltages.– Compare the results with the previous ones.

Z Carry out the measurements after full charging and subsequent resting for at least5 hours.


5.3.4 Annually



03.1

3 E

N

14

6 Aquamatik water replenishment system

6.1 Water replenishment system design

15 Water container16 Tap connection with ball cock17 Flow indicator18 Shut-off cock19 Locking coupling 20 Battery lock connector

15

16

17

18

19

20

> 3 m

+ -

03.1

3 E

N

14

6 Aquamatik water replenishment system

6.1 Water replenishment system design

15 Water container16 Tap connection with ball cock17 Flow indicator18 Shut-off cock19 Locking coupling 20 Battery lock connector

15

16

17

18

19

20

> 3 m

+ -

15

03.1

3 E

N6.2 Functional Description

The Aquamatik water replenishment system is used to adjust the rated electrolytelevel automatically on traction batteries for industrial trucks.

The battery cells are interconnected through hoses and are attached to the watersupply (e.g. water container) through a plug connection. When the shut-off cock isopened all the cells are filled with water. The Aquamatik plug controls the amount ofwater required and, at the relevant water pressures, ensures the water supply is shutoff and the valve is closed securely.

The plug systems have an optical level indicator, a diagnostic port to measure thetemperature and electrolyte density and a degassing port.

6.3 Adding water

Water should be added to the batteries just before the battery is fully charged. Thisensures that the amount of water added is mixed with the electrolyte.

6.4 Water pressure

The water replenishment system must be operated with a water pressure in the waterline of 0.3 bar - 1.8 bar. Any deviations from the permissible pressure ranges willaffect the operation of the systems.

Water drop

Assembly height above battery surface is between 3 - 18 m. 1 m corresponds to 0.1bar

Pressure water

The pressure regulating valve is adjusted to suit the system and must lie between 0.3- 1.8 bar.

15

03.1

3 E

N


The Aquamatik water replenishment system is used to adjust the rated electrolytelevel automatically on traction batteries for industrial trucks.

The battery cells are interconnected through hoses and are attached to the watersupply (e.g. water container) through a plug connection. When the shut-off cock isopened all the cells are filled with water. The Aquamatik plug controls the amount ofwater required and, at the relevant water pressures, ensures the water supply is shutoff and the valve is closed securely.

The plug systems have an optical level indicator, a diagnostic port to measure thetemperature and electrolyte density and a degassing port.

6.3 Adding water

Water should be added to the batteries just before the battery is fully charged. Thisensures that the amount of water added is mixed with the electrolyte.

6.4 Water pressure

The water replenishment system must be operated with a water pressure in the waterline of 0.3 bar - 1.8 bar. Any deviations from the permissible pressure ranges willaffect the operation of the systems.

Water drop

Assembly height above battery surface is between 3 - 18 m. 1 m corresponds to 0.1bar

Pressure water

The pressure regulating valve is adjusted to suit the system and must lie between 0.3- 1.8 bar.

03.1

3 E

N

16

6.5 Filling time

The filling time for a battery depends on the electrolyte level, the ambient temperatureand the filling pressure. Filling ends automatically. The water supply line must bedisconnected from the battery when the water has been filled.

6.6 Water quality


6.7 Battery tubing

The tubing of the individual plugs is in accordance with the existing electric circuit. Nochanges should be made.

6.8 Operating temperature

Batteries with automatic water replenishment systems should only be stored in roomswith temperatures > 0°C, as otherwise the systems could freeze.

03.1

3 E

N

16

6.5 Filling time

The filling time for a battery depends on the electrolyte level, the ambient temperatureand the filling pressure. Filling ends automatically. The water supply line must bedisconnected from the battery when the water has been filled.

6.6 Water quality


6.7 Battery tubing

The tubing of the individual plugs is in accordance with the existing electric circuit. Nochanges should be made.

6.8 Operating temperature

Batteries with automatic water replenishment systems should only be stored in roomswith temperatures > 0°C, as otherwise the systems could freeze.

17

03.1

3 E

N6.9 Cleaning measures

The plug systems must only be cleaned with purified water in accordance with DIN43530-4. No parts of the plugs must come into contact with solvent-based materialsor soap.

6.10 Service mobile vehicle

Mobile water filling vehicle with pump and filling gun to fill individual cells. Theimmersion pump in the container generates the necessary filling pressure. Theservice mobile must be at exactly the same height as the battery base.

17

03.1

3 E

N

6.9 Cleaning measures

The plug systems must only be cleaned with purified water in accordance with DIN43530-4. No parts of the plugs must come into contact with solvent-based materialsor soap.

6.10 Service mobile vehicle

Mobile water filling vehicle with pump and filling gun to fill individual cells. Theimmersion pump in the container generates the necessary filling pressure. Theservice mobile must be at exactly the same height as the battery base.

03.1

3 E

N

18

7 Electrolyte circulation


Electrolyte circulation ensures the supply of air during charging to mix the electrolyte,thereby preventing any acid layer, shortening the charge time (charge factor approx.1.07) and reducing the formation of gas during charging. The charger must besuitable for the battery and electrolyte circulation.

A pump in the charger produces the necessary compressed air which is introducedto the battery cells via a hose system. The electrolyte is circulated via the inlet air andthe electrolyte density level is constant over the entire length of the electrode.

Pump

In the event of a fault, e.g. if the pressure control system responds for an unknownreason, the filters must be checked and replaced if necessary.

Battery connection

A hose is attached to the pump module which together with the charge leads is routedfrom the charger to the charging connector. The air is passed on to the battery via theelectrolyte circulation coupling ducts in the connector. When routing make sure thehose is not bent.

Pressure monitoring module

The electrolyte circulation pump is activated when charging begins. The pressuremonitoring module monitors the build up of pressure during charging. This ensuresthat the required air pressure is provided for electrolyte circulation charging.

In the event of malfunctions such as:– Battery air coupling not connected to circulation module (if coupling is separate) or

faulty.– Leaky or faulty hose connections on battery or– Intake filter contaminated

a visual error message appears on the charger.

03.1

3 E

N

18

7 Electrolyte circulation


Electrolyte circulation ensures the supply of air during charging to mix the electrolyte,thereby preventing any acid layer, shortening the charge time (charge factor approx.1.07) and reducing the formation of gas during charging. The charger must besuitable for the battery and electrolyte circulation.

A pump in the charger produces the necessary compressed air which is introducedto the battery cells via a hose system. The electrolyte is circulated via the inlet air andthe electrolyte density level is constant over the entire length of the electrode.

Pump

In the event of a fault, e.g. if the pressure control system responds for an unknownreason, the filters must be checked and replaced if necessary.

Battery connection

A hose is attached to the pump module which together with the charge leads is routedfrom the charger to the charging connector. The air is passed on to the battery via theelectrolyte circulation coupling ducts in the connector. When routing make sure thehose is not bent.

Pressure monitoring module

The electrolyte circulation pump is activated when charging begins. The pressuremonitoring module monitors the build up of pressure during charging. This ensuresthat the required air pressure is provided for electrolyte circulation charging.

In the event of malfunctions such as:– Battery air coupling not connected to circulation module (if coupling is separate) or

faulty.– Leaky or faulty hose connections on battery or– Intake filter contaminated

a visual error message appears on the charger.

19

03.1

3 E

N

NOTE

If an installed electrolyte circulation system is seldom used or not used at all,or if the battery is subjected to severe temperature fluctuations, the electrolytemay flow back into the hose system.Attach a separate coupling system to the air inlet line, such as: locking coupling on

the battery side and through-coupling on the air supply side.

Schematic illustration

Electrolyte circulation on the battery and air supply via the charger.

19

03.1

3 E

N

NOTE

If an installed electrolyte circulation system is seldom used or not used at all,or if the battery is subjected to severe temperature fluctuations, the electrolytemay flow back into the hose system.Attach a separate coupling system to the air inlet line, such as: locking coupling on

the battery side and through-coupling on the air supply side.

Schematic illustration

Electrolyte circulation on the battery and air supply via the charger.

03.1

3 E

N

20

8 Cleaning batteries

Batteries and trays must be cleaned in order to – maintain cell insulation and protect cells from ground or external conductive parts.– Avoid damage from corrosion and stray currents.– Avoid excessive and varying automatic discharge of the individual cells or block

batteries due to stray currents.– Avoid electric sparking due to stray currents.

When cleaning the batteries make sure that:– The assembly site chosen for cleaning is close to a drainage system for processing

the electrolytic rinsing water.– All health and safety as well as water and waste disposal regulations are observed

when disposing of used electrolyte or rinsing water.– Protective goggles and clothing are worn.– Cell plugs are not removed or opened.– Clean the plastic components of the battery, in particular the cell containers, only

with water or water-based cloths without any additives.– After cleaning, the top of the battery is dried with suitable equipment, e.g.

compressed air or cloths.– Any fluid that has entered the battery box must be suctioned off and disposed of in

accordance with the above-mentioned regulations.

03.1

3 E

N

20

8 Cleaning batteries

Batteries and trays must be cleaned in order to – maintain cell insulation and protect cells from ground or external conductive parts.– Avoid damage from corrosion and stray currents.– Avoid excessive and varying automatic discharge of the individual cells or block

batteries due to stray currents.– Avoid electric sparking due to stray currents.

When cleaning the batteries make sure that:– The assembly site chosen for cleaning is close to a drainage system for processing

the electrolytic rinsing water.– All health and safety as well as water and waste disposal regulations are observed

when disposing of used electrolyte or rinsing water.– Protective goggles and clothing are worn.– Cell plugs are not removed or opened.– Clean the plastic components of the battery, in particular the cell containers, only

with water or water-based cloths without any additives.– After cleaning, the top of the battery is dried with suitable equipment, e.g.

compressed air or cloths.– Any fluid that has entered the battery box must be suctioned off and disposed of in

accordance with the above-mentioned regulations.

21

03.1

3 E

N

Cleaning the battery with a high pressure cleaner

Requirements– Cell connectors tight, plugged in securely– Cell plugs closed

Procedure• Follow the high pressure cleaner's user instructions.• Do not use any cleaning additives.• Observe the permissible cleaning device temperature setting of 140°C.

Z This generally ensures that the temperature does not exceed 60°C at a distance of30cm behind the outlet nozzle.

• Observe the maximum operating pressure of 50 bar.• Observe a minimum distance of 30 cm from the top of the battery.• The battery should be sprayed over its entire surface to avoid localised

overheating.Z Do not clean one spot for more than 3 seconds with the jet to avoid exceeding the

maximum battery surface temperature of 60°C.• After cleaning dry the battery surface with suitable materials e.g. compressed air or

cleaning cloths.

Battery cleaned.

21

03.1

3 E

N

Cleaning the battery with a high pressure cleaner

Requirements– Cell connectors tight, plugged in securely– Cell plugs closed

Procedure• Follow the high pressure cleaner's user instructions.• Do not use any cleaning additives.• Observe the permissible cleaning device temperature setting of 140°C.

Z This generally ensures that the temperature does not exceed 60°C at a distance of30cm behind the outlet nozzle.

• Observe the maximum operating pressure of 50 bar.• Observe a minimum distance of 30 cm from the top of the battery.• The battery should be sprayed over its entire surface to avoid localised

overheating.Z Do not clean one spot for more than 3 seconds with the jet to avoid exceeding the

maximum battery surface temperature of 60°C.• After cleaning dry the battery surface with suitable materials e.g. compressed air or

cleaning cloths.

Battery cleaned.

03.1

3 E

N

22

9 Storing the battery

NOTE

The battery should not be stored for longer than 3 months without charging asotherwise it will no longer be functional.

If the battery is to be taken out of service for a long period, it should be stored fullycharged in a dry room protected from frost. To ensure the availability of the batterythe following charges can be selected:

– Monthly compensation charge for PzS and PzB batteries or 3-monthly full chargefor PzV batteries.

– Trickle charge for a charge voltage of 2.23 volts x no. of cells for PzS, PzM and PzBbatteries or 2.25 volts x no. of cells for PzV batteries.

If the battery is to be taken out of service for a long period ( > 3 months), it should, asfar as possible, be charged to 50% of its charge level and stored in a dry roomprotected from frost.

10 Troubleshooting

If any faults are found on the battery or charger, contact the manufacturer's customerservice department immediately.


11 Disposal

Batteries marked with the recycling symbol and the sign showing acrossed-out rubbish bin should not be disposed of with ordinaryhousehold waste.

Buy-back terms and type of recycling are to be agreed with themanufacturer as described in § 8 of the battery legislation.

03.1

3 E

N

22

9 Storing the battery

NOTE

The battery should not be stored for longer than 3 months without charging asotherwise it will no longer be functional.

If the battery is to be taken out of service for a long period, it should be stored fullycharged in a dry room protected from frost. To ensure the availability of the batterythe following charges can be selected:

– Monthly compensation charge for PzS and PzB batteries or 3-monthly full chargefor PzV batteries.

– Trickle charge for a charge voltage of 2.23 volts x no. of cells for PzS, PzM and PzBbatteries or 2.25 volts x no. of cells for PzV batteries.

If the battery is to be taken out of service for a long period ( > 3 months), it should, asfar as possible, be charged to 50% of its charge level and stored in a dry roomprotected from frost.

10 Troubleshooting

If any faults are found on the battery or charger, contact the manufacturer's customerservice department immediately.


11 Disposal

Batteries marked with the recycling symbol and the sign showing acrossed-out rubbish bin should not be disposed of with ordinaryhousehold waste.

Buy-back terms and type of recycling are to be agreed with themanufacturer as described in § 8 of the battery legislation.

Operating instructions G · 11 11.14 DE A Correct Use and Application 1 General The industrial...

Documents

Transcript of Operating instructions G · 11 11.14 DE A Correct Use and Application 1 General The industrial...