Opel Astra G - unixauto.ro Information... · For the Opel Astra G chassis, RUVILLE offers a diverse...
Transcript of Opel Astra G - unixauto.ro Information... · For the Opel Astra G chassis, RUVILLE offers a diverse...
For the Opel Astra G chassis, RUVILLE offers a diverse product range that was nearly completed with the introduction of chassis springs for the front and rear axle. During repair work, both general as well as specific procedures have to be followed for the respective components.
Vehicle-specific installation instructions:
For some chassis components and for the wheel bearings in the Opel Astra G, specific installation instructions have to be followed. These are described in more detail below. The relevant articles are highlighted in grey in the table.
OPEL ASTRA G
CHASSIS
Basic installation instructions:
Use self-locking nuts, replace them as needed. In general, replacing the bolts and screws is always recommended. Comply with the tightening torques specified in the manufacturer’s
specifications. Tighten steering components under load. Following work on the chassis, it is always advisable to measure the
chassis; in the case of some repairs, it is also mandatory. Use the designated special tools.
KnOw-HOw In dETAIL PAGE 1
Every new model or series also involves new installation specifications for the chassis. RUVILLE passes on this up-to-date knowledge and expertise to auto repair garages. For more information about our training, visit www.ruville.de or contact our technical trainer, Remo Schönsee, directly at [email protected]
wE PASS On OUR PRACTICAL KnOwLEdGE THROUGH TRAInInG
TO BE FOLLOwEd In GEnERAL ALL RUVILLE CHASSIS COMPOnEnTS FOR THE OPEL ASTRA G
KNOW-HOW IN DETAIL CAN ALSO BE DOWNLOADED
ONLINE AT
www.RUVILLE.dE ➜ SERVICE ➜ dOwnLOAdS
➜ TECHnICAL InFORMATIOn ➜ KnOw-HOw In dETAIL
➜ OPEL ASTRA G CHASSIS
TO BE FOLLOwEd FOR CERTAIn COMPOnEnTS
Opel Astra G
Article no. designation Installation point
5322 Wheel bearing set Rear axle for 4-hole rim
5323 Wheel bearing set Rear axle for 4-hole rim
5327 Wheel bearing set Rear axle for 4-hole rim
5330 Wheel bearing set Front axle for 5-hole rim
5331 Wheel bearing set Front axle for 5-hole rim
5332 Wheel bearing set Front axle for 5-hole rim
5333 Wheel bearing set Front axle for 5-hole rim
5334 Wheel bearing set Rear axle for 5-hole rim
75311 Drive shaft joint Left and right wheel side
325368 Engine mounting Centre
815301 Dust cover kit, shock absorber Front axle
825328 Suspension strut mounting Front axle
894318 Chassis spring Rear axle
895338 Chassis spring Front axle
915355 Support /guide joint Both sides
915358 Tie rod end Both sides
915361 Rod/strut, stabiliser Both sides
935306 Wheel suspension arm Triangular control arm, left
935307 Wheel suspension arm Triangular control arm, right
945307 Steering bellows set Front axle, both sides
985334 Steering bellows set Front axle, both sides
985308 Steering mounting Front axle, both sides, front
985334 Steering mounting Front axle, both sides, rear
985359 Bearing bush, stabiliser Front axle 16mm
985361 Bearing bush, stabiliser Front axle 18mm
985365 Axle body mounting Rear axle, both sides
75311S Drive shaft joint kit Wheel side, both sides
915359S Axial joint, tie rod Axial joint kit, front axle, both sides
nEw
Article: 895338 | Chassis spring 815301 | dust cover kit, shock absorber 825328 | Suspension strut mounting
Before dismantling the suspension strut, mark the positioning and installation position of the individual components. Springs and shock absorbers must always be repla-ced in pairs. If the suspension strut is only removed, and not dismantled, the attachment nut for the support mounting on the shock absorber piston rod must be che-cked before installation using the specified tightening torque. Check the camber and adjust if necessary.
Article: 985365 | Axle body mounting
To make it easier to remove the dam-ping bushes, they should be sprayed with universal spray oil in the area of the rear axle mounting one day before removal. The damping bushes of the rear axle must always be replaced in pairs.The bolt connection (rear axle holder at damping bush) is tightened during installation of the rear axle, while main-taining the correct spacing between the spring mounting on the rear axle and the spring mounting on the vehicle underbody.
Article: 935306 | wheel suspension arm 935307 | wheel suspension arm 985308 | Steering mounting 985334 | Steering mounting
If the steering mounting has to be replaced, the air supply, if applicable, must be converted (retrofitted).Before tightening the bolts, lower the vehicle to the floor, load both front seats with 70 kg each and tighten the bolt connections for the steering mountings at the front axle on the inspection stand or in the pit.The bearing bushes must be replaced in pairs. Before pressing in, coat the bearing bushes and mountings with soap solution. Fit the rear bearing bush (4) up against the mounting so that the weld seam is aligned with one of the recesses in the bush (arrows).
KnOw-HOw In dETAIL PAGE 2
OPEL ASTRA G
CHASSIS
Sedan 168 ± 10 mmCaravan 198 ± 10 mm
Article: 915355 | Support/guide joint
Before replacing the support joint, drill out the rivet heads (1) using a drill with a 12 mm diameter bit. Drill out the rivets as far as the support surface (guideline) of the guide, then tap off carefully using a flat chisel and remove the remains of the rivets.Remove the guide joint and coat the bore with corrosion protection. New special bolts are supplied with the new support joint, which in all cases must be used for the installation (mandatory)! Insert the special bolts as shown in Fig. 2.
Fig.1 Fig.2
Article: 5322 | wheel bearing set 5323 | wheel bearing set 5327 | wheel bearing set 5334 | wheel bearing set
Measure the lateral run-out:Installation of the test device:Fit the test gauge (3) with test gauge holder (2) and magnet (4) to the backing plate or cover plate. Place the probe tip (1) of the test gauge against the outer edge of the bearing unit, and turn the wheel bearing unit slowly.
Measurement result:Permissible lateral run-out max. 0.04 mm. If the result deviates from this set value, replace the wheel bearing unit.
Measure the radial run-out:Installation of the test device:Fit the test gauge (3) with test gauge holder (2) and magnet (4) to the backing plate or cover plate. Place the probe tip (1) of the test gauge against the bearing unit (as in Fig. 2), and turn the wheel bearing unit slowly.
Measurement result:Permissible radial run-out max. 0.05 mm. If the result deviates from this set value, replace the wheel bearing unit.
Fig.1
Fig.2
Article: 985359 | Bearing bush, stabiliser 985361 | Bearing bush, stabiliser
To replace the stabiliser bushes, the front axle must be lowered. The axle may only be lowered to a maximum permissible distance of 55 mm.Before fitting the new bearing bushes, a special lubricating grease must be applied to the inner surfaces (not supplied). The slot in the bushes must point forward in the direction of travel.