op-amp report
-
Upload
gaurav-singh -
Category
Documents
-
view
200 -
download
2
Transcript of op-amp report
“OPAMP APPLICATION TRAINER BOARD”
2011-2012A Minor Project Report Submitted to
Rajiv Gandhi Proudyogiki Vishwavidyalaya In partial fulfillment of the
Degree of Bachelor of EngineeringIn
Electronics & communication
Guided by: Submitted by:Mr. GANESH MUKATI ANKIT GUPTA(Sr. Lecturer) (0805EC091003)Mr. GAURAV DASONDHI DEEPAK DASHORE
(Lecturer) (0805EC091017) Electronics & communication Department GAURAV SINGH (0805ec091022) RITESH KUDEKAR (0805EC091064)
Department of Electronics &CommunicationJAWAHARLAL INSTITUTE OF TECHNOLOGY
BORAWAN (KHARGONE), M.P.
JAWAHARLAL INSTITUTE OF TECHNOLOGYBORAWAN (KHARGONE), M.P.
CERTIFICATE
This is to certify that minor project entitled “OPAMP APPLICATION BREAD BOARD TRAINER” is submitted by “Ankit Gupta, Deepak Dashore, Gaurav Singh, Ritesh Kudekar” students of Third year of “Electronics & Communication” year 2011-2012 in partial fulfillment of the requirements of “Rajiv Gandhi Proudyogiki Vishwavidyalaya Bhopal” for the award of the Degree of Bachelor of Engineering in Electronics & Communication branch of “Jawaharlal Institute of Technology”, affiliated to R.G.P.V. BHOPAL (M.P.)
Head of Department Project GuideMr. SANJAY CHOUHAN Mr. GANESH MUKATI Mr. GAURAV DASONDHI
Dr. ATUL UPADHYAY Dr. D.K. PANDA PRINCIPAL DIRECTOR
JIT Borawan, Khargone JIT Borawan, Khargone
JAWAHARLAL INSTITUTE OF TECHNOLOGYBORAWAN (KHARGONE), M.P.
CERTIFICATE OF APPROVAL
This is to certify that minor project entitled “OPAMP APPLICATION BREAD BOARD TRAINER” is submitted by “Ankit Gupta, Deepak Dashore, Gaurav Singh, Ritesh Kudekar” in partial fulfillment of the requirements for the award of Bachelor of Engineering in Electronics & Communication branch during the academic year 2011-2012 from “Jawaharlal Institute of Technology”, affiliated to R.G.P.V. BHOPAL (M.P.)
External Examiner: Internal Examiner:
ACKNOWLEDGEMENT
We the students of third year of electronics and communication engineering are really thankful to our Lecturers team for guiding us so precisely, so we can take the challenge on such ambitious project of advanced security systems. We always thankful to Mr. Sanjay Chouhan, Head of Department (Electronics and Communication Engg.) for cooperation and trust which they shown in us and for supporting us in this project, so we can focus on the target.
We are thankful to our Project Guide Mr. Ganesh Mukati and Mr. Gaurav Dasondhi for such a devoted guidance on our project and showing faith in our project, their instructions are like the guiding light on the path of the excellence of our graduation period. We also thankful to, Mr. Yogendra Singh Patel, for the constantly working on potential of the students and always telling them what is the right way to solve the problems, they are our inspiration for solving the problems at the professional level. We are also really thankful to, Mr. Girijesh Dasoundhi and all the faculty members for being shining stars of our night sky. In the end we are thankful Dr. Atul Upadhyay , Principal (J.I.T, Borawan), and Dr. D.K. Panda Director (J.I.T, Borawan) for providing us such good operative
ANKIT GUPTA DEEPAK DASHORE GAURAV SINGH RITESH KUDEKAR
Abstract
“OPAMP APPLICATION TRAINER BOARD”
Operational amplifier is usually Called Op Amps. An amplifier is a device that accepts a varying input signal and produces a similar output signal with a larger amplitude.
They are the basic components used to build analog circuits. The name “operational amplifier” comes from the fact that they were originally used to perform mathematical operations such as integration and differentiation.
We also easily perform its application on bread board trainer and check that our project will successes or not. So we show on this project the various application of opamp using bread board trainer.
Applications: • Inverting amplifier• Non-inverting amplifier• Summing amplifier• Comparator• Integrator• Differentiator
This project is very less expensive, so we get good benefits of this project.
Table of ContentsPage No.
Chapter-1 INTRODUCTION
Chapter-2 BASIC THEORY
Chapter-3 HARDWARE IMPLEMENTATION
3.1 Block Diagrams of op-amp
3.2 Description of Block Diagrams
3.3 Op-amp applications
3.4 Circuit Components
3.5 PCB Layout
3.6 PCB Design Techniques
Chapter-4 CONCLUSION
4.1 Advantages of op-amp application
4.2 Limitations of op-amp application
4.3 Application of Project
4.4 Future Enhancement
Chapter-5 References :
Chapter-1 INTRODUCTION:
Operational amplifier is usually Called Op Amps. An amplifier is a
device that accepts a varying input signal and produces a similar output signal with a
larger amplitude.
An operational amplifier is a DC-coupled high-gain electronic voltage amplifier with
a differential input and, usually, a single-ended output. An op-amp produces an output
voltage that is typically hundreds of thousands times larger than the
voltage difference between its input terminals
. Op amps are high gain amplifiers, and are used almost invariably with overall loop
feedback. The principle of the feedback amplifier has to rank as one of the more notable
developments 20th century— right up there with the automobile or airplane for breadth
of utility , and general value to engineering. And, most importantly, such feedback
systems, although originally conceived as a solution to a communications problem,
operate today in more diverse situations. This is a clear tribute to the concept’s
fundamental value.
Circuit Notation of OP-AMP:-
AN IDEAL OP-AMP:-
+
~
AVin
Vin Vout
Zout=0
Ideal op-amp
Op-amps are one of the basic building blocks of Analogue Electronic
Circuits. Operational amplifiers are linear devices that have all the properties required for
nearly ideal DC amplification and are therefore used extensively in signal conditioning.
filtering or to perform mathematical operations such as add, subtract, integration and
differentiation.
An ideal Operational Amplifier is basically a three-terminal device which consists of two
high impedance inputs, one called the Inverting Input, marked with a negative or "minus"
sign, ( "-" ) and the other one called the Non-inverting Input, marked with a positive or
"plus" sign ( "+" ).
Chapter-2 BASIC THEORY:
A final major transitional phase of op amp history began with
the development of the first IC op amp, in the mid 1960’s. Once IC technology became
widely established, things moved quickly through the latter of the 20 th century years, with
milestone after milestone of progress being made in device performance. This story
begins back in the vacuum tube era and continues until today (2002).
The Operational Amplifier (Op Amp) can be used in many different ways. The Op-amp
has two inputs an inverting input (-) and a non-inverting input (+) and one output. A
signal applied to the inverting input will have its polarity reversed on the output. A signal
applied to the non-inverting input will retain its polarity on the output. The gain or
amplification of the signal is determined by a feedback resistor that feeds some of the
output signal back to the inverting input .The smaller the resistor, the lower the gain.
Some typical op-amp pin outs are shown below. The most common are the 741 and 1458
dual op-amp.
The operational amplifier is arguably the most useful single device in analog electronic
circuitry. With only a handful of external components, it can be made to perform a wide
variety of analog signal processing tasks. It is also quite affordable, most general-purpose
amplifiers selling for under a dollar apiece. Modern designs have been engineered with
durability in mind as well: several "op-amps" are manufactured that can sustain direct
short-circuits on their outputs without damage.
One key to the usefulness of these little circuits is in the engineering principle of
feedback, particularly negative feedback, which constitutes the foundation of almost all
automatic control processes. The principles presented here in operational amplifier
circuits, therefore, extend well beyond the immediate scope of electronics. It is well
worth the electronics student's time to learn these principles and learn them well.
Pin Diagram of an OP-AMP:-
LM741 Operational Amplifier: Circuit Architecture:-
Chapter-3 HARDWARE IMPLEMENTATION
3.1 Block Diagram of op-amp:
3.2 Description of Block Diagram:
An operational amplifier is a direct-coupled high-gain
amplifier usually consisting of one or more differential amplifiers and usually followed
by a level translator and an output stage. The output stage is generally a push-pull
symmetry pair. An op-amp is available as a single integrated ckt package.
An op-amp is a high quality amplifier. It contains four stages, which are connected in
cascaded manner.
The first stage of an op.amp is a double ended differential amplifier. This stage provides
maximum voltage gain. This stage should employ a current source at the common emitter
node for good common mode rejection.
This second stage is an intermediate gain stage called single ended differential amplifier.
It does not require a current source in the emitter. Normally the second stage is needed
only to provide some additional gain. Its input resistance should be relatively high to
prevent excessive loading of the first stage.
The third stage is an emitter follower, which produces unity gain. It has high input
resistance and also low output resistance. It matches the output of amplifier stage and the
input of output stage.
The fourth stage is a level translator and output driver. This stage is used for preventing
any undesired dc current in the load and increasing the permissible output voltage swing.
Hence it supplies large output voltage or current
3.3 Op-amp Applications is -
• Inverting amplifier
• Non-inverting amplifier
• Summing amplifier
• Comparator
• Integrator
• Differentiator
Inverting amplifier:
An inverting amplifier inverts and scales the input signal. As long as
the op-amp gain is very large.
The amplifier gain is determined by two stable external resistors (the feedback resistor Rf
and the input resistor Rin) and not by op-amp parameters which are highly temperature
dependent
As with the non-inverting amplifier, we start with the gain equation of the op-amp:
This time, – is a function of both and due to the voltage divider formed by
a and . Again, the op-amp input does not apply an appreciable load, so:
Substituting this into the gain equation and solving for :
If is very large, this simplifies to
.
In particular, the Rin–Rf resistor network acts as an electronics) where the inverting (i.e.,
−) input of the operational amplifier is like a fulcrum about which the seesaw pivots. That
is, because the operational amplifier is in a negative-feedback configuration, its internal
high gain effectively fixes the inverting (i.e., −) input at the same 0 V (ground) voltage of
the non-inverting (i.e., +) input, which is similar to the stiff mechanical support provided
by the fulcrum of the seesaw. Continuing the analogy.
Non-inverting amplifier:
The gain equation for the op-amp is:
However, in this circuit – is a function of because of the negative feedback
through the network. and form a voltage divider, and as – is a high-
impedance input, it does not load it appreciably. Consequently:
where
Substituting this into the gain equation, we obtain:
Solving for :
If is very large, this simplifies to
.
Non-inverting amplifier Amplifies a voltage (multiplies by a constant greater than 1).
The input impedance is at least the impedance between non-inverting ( + ) and inverting (
− ) inputs, which is typically 1 MΩ to 10 TΩ, plus the
impedance of the path from the inverting ( − ) input to ground (i.e., R1 in
parallel with Rf). Because negative feedback ensures that the non-inverting and inverting
inputs match, the input impedance is actually much higher.
The non-inverting ( + ) and inverting ( − ) inputs draw small leakage
currents into the operational amplifier. These input currents generate
voltages that act like unmodeled input offsets. These unmodeled
effects can lead to noise on the output.
Summing amplifier:
The summing amplifier is a handy circuit enabling you to add several signals
together. What are some examples? If you're measuring temperature, you can add a
negative offset to make the display read "0" at the freezing point. On a precision
amplifier, you may need to add a small voltage to cancel the offset error of the op amp
itself. An audio mixer is another good example of adding waveforms (sounds) from
different channels (vocals, instruments) together before sending the combined signal to a
recorder.
Although, there are many ways to make a summer, this one is nice because it keeps the
interaction between inputs at a minimum. What does that mean for you the designer? You
can change the gain or add another input without messing with the gains of the other
inputs. Just remember that the circuit also inverts the input signals. Not a big deal. If you
need the opposite polarity, put an inverting stage before or after the summer.
Comparator:
In electronics, a comparator is a device that compares two voltages or
currents and switches its output to indicate which is larger. They are commonly used in
devices such as Analog-to-digital converters.
A comparator is designed to produce well limited output voltages that easily interface
with digital logic. Compatibility with digital logic must be verified while using an op-
amp as a comparator. An operational amplifier (op-amp) has a well balanced difference
input and a very high gain. This parallels the characteristics of comparators and can be
substituted in applications with low-performance requirements. Many op-amps have back
to back diodes between their inputs. Op-amp inputs usually follow each other so this is
fine. But comparator inputs are not usually the same. The diodes can cause unexpected
current through inputs.
Differentiator:
The differentiator as its name implies, the circuit performs the
mathematical operation of differentiation ; that is the output waveform is the derivative of
the input waveform. The differentiator may be constructed from basic inverting amplifier
if an input resistor R1 is replaced by a capacitor C.
The output V0 is equal to the RfC times the negative instantaneous rate of change of the
input voltage Vin with time. Since the differentiator performs the reverse of the
integrator’s function, a cosine wave input will produce a sine wave output, or a triangular
input will produce a square wave output.
A differentiator circuit consists of an operational amplifier, resistors are used at
feedback side and capacitors are used at the input side. The circuit is based on the
capacitors current to voltage relationship:
where I is the current through the capacitor, C is the capacitance of the capacitor, and
V is the voltage across the capacitor. The current flowing through the capacitor is
then proportional to the derivative of the voltage across the capacitor. This current
can then be connected to a resistor, which has the current to voltage relationship:
where R is the resistance of the resistor.
If Vout is the voltage across the resistor and Vin is the voltage across the capacitor, we
can rearrange these two equations to obtain the following equation.
Integrator:
The integrator is a circuit in which the output voltage waveform is the
integral of the input voltage waveform . such a circuit is obtained by using a basic
inverting amplifier configuration if the feedback resistor Rf is replaced by a capacitor Cf.
Output equation indicates that the output voltage is directly proportional to the negative
integral of the input voltage and inversely proportional to the time constant R1Cf. For
example ,if the input is a sine wave, the output will be a cosine wave; or if the input is a
square wave, the output will be a triangular wave.
3.4 Circuit Components:
For op-amp application trainer kit
• Op-amp IC• Resistors• Variable resistor• Ceramic capacitors
• Switch • Banana socket
• LM 741 CN• 10 K (6)• 10 K (2)• .1 uF (3)• 1 uF (1)
• 2 mm
3.5 Power supply:
The objective here is to build a dual power supply that generates regulated
+12 volts and -12 volts from 230VAC mains. Such a supply is a very common
requirement in all those circuits that use op-amps. Since op-amps are very widely used in
a variety of circuits of hobbyists’ interests, construction of this project could serve as a
very useful tool in testing all those circuits that need a dual supply. Each of the outputs in
the circuit shown in Fig.8.1 has a current delivering capability of 250mA. You would
also discover this circuit to be an integral part of the more complex circuits that are mains
operable.
Circuit diagram of power supply:
PCB layout:
3.6 PCB DESIGN TECHNIQUES:-
PCB Designing:-
We have taken a blank copper PCB, then we have designed layout
using Express PCB software. After that we have printed the layout of the power supply
on the blank copper PCB, Then drilled the appropriate holes.
Chemical etching Process:-
Now the printed PCB is taken for etching process. The PCB is dropped in the solution of
Hydrochloric Acid (HCL) and Sulphuric Acid
Soldering:- In the soldering process all the circuit components are soldered onto the
PCB. Soldering process requires soldering wire and soldering iron along with the
components which are to be soldered.
Chapter-4 CONCLUSION
4.1 Advantages:-
Op-amps are made of transistors. The advantages of using op-amps as gain
blocks instead of simpler transistor circuits is usually simpler design made with fewer
mounted parts (even though the total device count is higher, considering the complexity
inside the op-amps) and more ideal and predictable performance, often at lower supply
current. There are exceptions, where individual transistors are more suited to the desired
functions, when higher frequencies, larger currents, voltages or higher power are
involved. Also, if cost is more important than ideal performance, transistor designs can
often beat op-amp ones, even though there are some very low cost op-amps available.
4.2 Limitations of op-amp:-
The primary limitation of op-amp is that they are not especially fast: The typical
performance degrades rapidly for frequencies greater than about 1 MHz, although some
models are designed specially to handle higher frequencies.
4.3 Application of Project:-
This operational amplifier kit can be used in electronics labs to
understand the basic operations performed by OP-AMP. It is easy to handle and easily
under stable by the students who are willing to understand the basic applications of OP-
AMP.
chapter-5 REFERENCES
Websites:
http://www.ti.com/product/LM741
www.electronics world.com
www.opamp circuits.com
Books:
A.N. Gayakwad , op-amp integration
Jacob Milllman & Halkias , Integrated Electronics
R.S. Sedha, Applied electronics