OmniTouch 7” · 5.7/5.7e - > OT7 23 7/10/2013 OmniTouch 7 Requires Omni Firmware 3.9 or > •...
Transcript of OmniTouch 7” · 5.7/5.7e - > OT7 23 7/10/2013 OmniTouch 7 Requires Omni Firmware 3.9 or > •...
Presented by: Jay Correa
OmniTouch 7”
OmniTouch 7”
7/10/2013 2
The new OmniTouch 7 including: hardware differences from 5.7/5.7e
and new UI.
Intro
7/10/2013 3
Developed using our next
generation UI Engine
Not based on the current
Android app!
Replacement for 5.7 / 5.7e
line
Totally new hardware, fast
and reliable.
Specifications
7/10/2013 4
1.0Ghz ARM Cortex A8 CPU
800x480 Wide LCD
Capacitive Touch
Power-Over-Ethernet (POE)
• Or 12V w/ external supply
microSD Card Slot
2 Digital MEMS Mics
Ambient Light Sensor
7.25” x 5.125” x 0.55” visible
6.0” x 4.0” x 1.0” in-wall
Comparison
7/10/2013 5
5 Easy Installation Steps
7/10/2013 6
1. Cut Drywall To Included Template
• Ruff-In-Size = 6.0” x 4.0” x 1.0”
2. Install Bracket into the newly cut hole.
3. Connect CAT5 POE to Touchscreen
4. “Snap” the touchscreen into Installed Bracket
5. Enter Controller Address, Port, and Encryption Key when
prompted.
Installation Bracket (Drywall)
7/10/2013 7
Mounting hardware included
Two Mounting Methods
• 4 Screws into drywall
• 4 Tabs
Touchscreen snaps into bracket
• Secured with two screws from bottom
Installation Options (Drywall)
7/10/2013 8
New Install
• Cut Drywall
• Install Bracket
• Install OmniTouch 7
3.9” Replacement
• Same as New Install
5.7 / 5.7e Replacement
• Cut Drywall
• Install Trim ring
• Install Bracket
• Install OmniTouch 7
Concrete install
7/10/2013 9
Concrete install
7/10/2013 10
Concrete install
7/10/2013 11
Controller Address
Controller Port
Encryption Key
DHCP Only
7/10/2013 12
Configuration
New Features
7/10/2013 13
New UI Storyboard / Design
• Modern UI (Android 2.3.3)
• Swipes / Drags
• Speed
• Fast, IP Camera Video is fluid
• Simplified, more clear and concise UI
Easier Setup (Controller Address, Port, Key)
Selectable Themes
Rooms Based
Always available Top / Bottom
Bars
Large and realistic icons. Drag
or swipe for more.
Icons Show / Hide depending
on controller configuration
7/10/2013 14
Home Page
Zones / Areas buttons show if
needed
Zone(s) Not Ready rotating
banner.
7/10/2013 15
Security
Buttons can be placed in
Extended Setup Rooms for
Scenes
Finger Swipe or Drag to scroll
through more sliders / units
Pressing the “Bulb” will toggle
the Unit.
7/10/2013 16
Control
Landing Page allows quick
access to set points and status
Details will launch a detailed
view
7/10/2013 17
Thermostats
Cameras from Extended Setup.
Makes for EASY setup!
Drag / Swipe through Icons
Tap Image to display “full
screen”
MUCH improved Video
performance.
7/10/2013 18
Cameras
Control and Metadata through
Omni Controller
Easily select or power off
zones
(Not final Graphics)
7/10/2013 19
Audio
Select Desired Button
Press “Run Button”
7/10/2013 20
Buttons
View Status
Lock / Unlock
Swipe / Drag for more
7/10/2013 21
Locks
Non- configuration settings
now exposed through the UI
Press and hold “Settings” to
get into dealer configuration
7/10/2013 22
Settings
5.7/5.7e - > OT7
7/10/2013 23
OmniTouch 7 Requires Omni Firmware 3.9 or >
• Uses Extended Setup
• Notifications
No HTX/HTX2 Support
No Music Gateway / iPod Dock Support (Browsing Media)
No Nuvo Grand Concerto “Menu” button support (Browsing Media)
• Metadata
• Transport Controls
HLC Rooms is being replaced by Extended Setup Rooms
Leviton.com
Thank You