old-9503268-RevF pg 1 · 1 2 2 1. Place wire manager underneath worksurface where desired. 2....
15
NOTES: • T-Legs and Post Legs provide a nominal table height of 28-1/2". • Glides and casters are interchangeable, while keeping the same table height. • The height range is 25-1/2" to 31-1/2" for adjustable T-Legs and adjustable Post Legs. • The height range is 28-1/2" to 45" for standing height adjustable Post Legs. Page Topic 2-13 T-Legs & Post Legs Installation 14 Typical Table Configurations 15 Wire Manager Installation Table of Contents Page 1 of 15 939503268 Rev G Groupwork ™ Tables NOTE: To ensure stability and prevent possible injury, standing height and standard height post legs with casters are not permitted on any 18" deep tables and half-round tables smaller than 30 x 60. Standing height post legs with casters are not permitted on 24 x 42 kidney shape top and 24 x 48 trapezoid shape tops. If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by people who want to help you. (Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: 1.616.247.2500) Or visit our website: www.steelcase.com © 2014 Steelcase Inc. Grand Rapids, MI 49501 U.S.A. Printed in U.S.A. ®
Transcript of old-9503268-RevF pg 1 · 1 2 2 1. Place wire manager underneath worksurface where desired. 2....
NOTES:• T-Legs and Post Legs provide anominal table height of 28-1/2".• Glides and casters areinterchangeable, while keepingthe same table height.• The height range is 25-1/2" to31-1/2" for adjustable T-Legs andadjustable Post Legs.• The height range is 28-1/2" to45" for standing height adjustablePost Legs.
Page Topic
2-13 T-Legs & Post Legs Installation
14 Typical Table Configurations
15 Wire Manager Installation
Table of Contents
Page 1 of 15939503268 Rev G
Groupwork™ Tables
NOTE: To ensure stability and prevent possible injury, standing height and standard height post legs with casters are not permitted on any 18" deep tables and half-round tables smaller than 30 x 60. Standing height post legs with casters are not permitted on 24 x 42 kidney shape top and 24 x 48 trapezoid shape tops.
If you have a problem, question, or request, callyour local dealer, or Steelcase Line 1 at888.STEELCASE (888.783.3522)for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: 1.616.247.2500)Or visit our website: www.steelcase.com© 2014 Steelcase Inc. Grand Rapids, MI 49501 U.S.A.
Printed in U.S.A.
®
Page 2 of 15939503268 Rev G
Attaching Legs to Worksurfaces
Post Leg(Fixed Heightand AdjustableHeight)
T-Leg(Fixed Heightand AdjustableHeight)
NOTE:There is no difference ininstallation of fixed heightand adjustable height legs.
Standing HeightPost Leg(AdjustableHeight Only)
CAUTION:Post legs with casters are not to be used with 18" deep tables. See note on page 1 for details.
®
Page 3 of 15939503268 Rev G
A B
A B
Rectangular Worksurfaces 18" and 24" Deep Pilot Hole Locations
Post Leg
A B
A B
AB
Angled T-Leg
B
A
AB
B
A
NOTE:Keep screws in the first t-leg loose until thesecond t-leg, on the same end, is looselyattached to the table top. Tighten the screwsstarting from the middle of the table top andworking towards the outside corner.
18"Deep
24"Deep
24"Deep
NOTE:18" deep rectangular worksurfaces accommodate post legs only.
18" x 84"
24" x 84"
24" x 84"
CAUTION:Post legs with casters are not to be used with any 18" deep rectangular tops. See note on page 1 for details.
®
18x60 39" Not needed Not needed18x66 48" Not needed Not needed18x72 48" Not needed Not needed18x84 57" Not needed Not needed24X60 57" Not needed 39"24X66 57" Not needed 39"24X72 57" Not needed 47"24X84 72" Not needed 57"30X60 57" 48" 57"30X66 57" 57" 57"30X72 57" 57" 57"
Size (LPL or HPL)
Post Leg Brace Size
T-Leg Brace Size (inline)
T-Leg Brace Size (angled)
Page 4 of 15939503268 Rev G
A B
A B
Rectangular Worksurfaces 30" Deep Pilot Hole Locations
Post Leg Angled T-Leg
A B
A B
T-Leg
A
B
B
B
B
A
A
A
AB
B
A
AB
B
A
NOTE:Keep screws in the firstt-leg loose until the secondt-leg, on the same end, isloosely attached to the tabletop. Tighten the screwsstarting from the middle ofthe table top and workingtowards the outside corner.
®
Page 5 of 15939503268 Rev G
Half Round Table without Cutout and (3) Legs
Post Leg
A BB
A B
A
A
B
B
B
A
A
B
18" x 36"
A B
A BB
24" x 48"
T-legPost Leg
B
A
A
B
NOTE:18" x 36" half round tablew/o cutout accommodatepost legs only.
CAUTION:Post legs with casters are not to be used on any half round tops smaller than 30" x 60". See note on page 1 for details.
®
Page 6 of 15939503268 Rev G
Half Round Table without Cutout and (4) Legs
Post Leg Angled T-Leg and T-leg
A B
A B
A B
A B
A
A
A
A
B
B
B
B
A
A
A
B
B
B
A
B
30" x 60"30" x 60"
®
Page 7 of 15939503268 Rev G
Half Round Table with Cutout and (3) Legs
Post Leg
A BB
A B
A
A
B
B
B
A
A
B
21" x 42"
A B
A BB
27" x 54"
T-legPost Leg
B
A
A
B
NOTE:21" x 42" half round tablew/ cutout accommodatepost legs only.
CAUTION:Post legs with casters are not to be used on any half round tops smaller than 30" x 60". See note on page 1 for details.
®
Page 8 of 15939503268 Rev G
Half Round Table with Cutout and (4) Legs
Post Leg Angled T-Leg and T-leg
A B
A B
A B
A B
A
A
A
A
B
B
B
B
A
A
A
B
B
B
A
B
30" x 60"30" x 60"
®
Page 9 of 15939503268 Rev G
Personal Tables
Post Leg Angled T-leg
A
B
B
A
B
B
A
A
B
AA
B
B
B
A
A
NOTE:Keep screws in the firstt-leg loose until the secondt-leg, on the same end, isloosely attached to the tabletop. Tighten the screwsstarting from the middle ofthe table top and workingtowards the outside corner.
NOTE:18" x 36" personal tableaccommodate post legs only.
18" x 36"
24" x 42"KIDNEY SHAPED
24" x 42"
24" x 42"KIDNEY SHAPED
24" x 42"
CAUTION:Standing height and standard height post legs with casters are not to be used on any of the above mentioned tops. See note on page 1 for details.
®
Page 10 of 15939503268 Rev G
AB
AB
Post Leg Angled T-Leg T-Leg
AB
B
BA
NOTE:Keep screws in the firstt-leg loose until the secondt-leg, on the same end, isloosely attached to the tabletop. Tighten the screwsstarting from the middle ofthe table top and workingtowards the outside corner.
Trapezoid Tables
24" x 48"
30" x 60"
NOTE:24" x 48" trapezoid tablesaccommodate post legs only.
30" x 60" 30" x 60"
AB
BA
A
AB
A
B
B
A
A
B
B
A
CAUTION:Standing height post legs with casters are not to be used on 24" x 48" trapezoid tops. See note on page 1 for details.
NOTE:Standard height post legs with casters are allowed on 24" x 48" trapezoid tops.
®
Page 11 of 15939503268 Rev G
Triangle Tables
B
A
NOTE:Triangle tablesaccommodate post legs only.
24"Straight
30"Straight
36"Convex
42"Convex
B
A
BA
AB
AB A
B
CAUTION:Post legs with casters are not to be used on these triangular tops.
NOTE:This product has been culled as of March 2007.
®
Page 12 of 15939503268 Rev G
Square Concave Tables
Post Leg Angled T-leg
A
A
B
B
BB
A
A
A
36"
42" 42"
36"
A BB
A BA B
®
Page 13 of 15939503268 Rev G
Corner Bubble Tables
Post Leg Angled T-leg
A
A
B
B
BB
A
A
A
30"
36"36"
30"
A BB
A BA B
NOTE:This product has been culled as of March 2007.
®
Page 14 of 15939503268 Rev G
Typical Table Configurations
20"D bracketsfor 30"D Tops
Triangle Table withThree Rectangular Tables
14"D bracketsfor 24"D Tops
Corner Bubble Table withTwo Rectangular Tables
30"
30"
Two Half Round Tables withTwo Rectangular Tables
45º Corner Table withTwo Rectangular Tables
90º Corner Table withTwo Rectangular Tables
24"
30"
18"
30"
24"
18"
24"/30"
24"/30" 24"/30"
18"
24"
24"
24"
18"
18"
NOTE: Post legs and T-legs are interchangeable for all configurations. Post legs are shown.
27" x 54"
21" x 42"
24" x 48"
21" x 42"
27" x 54"
24" x 48"
Use style # TSATTIE when requiring (6) Tie Plates and (24) Screws.Use style # TSATPL14 when requiring a 14" Support Plate and (8) Screws.Use style # TSATPL20 when requiring a 20" Support Plate and (8) Screws.
NOTE:The 18" product has been culled as of March 2007.
NOTE:The 18", 24" & 30" product has been culled as of March 2007.
NOTE:This product has been culled as of March 2007.
®
Page 15 of 15939503268 Rev G
Wire Manager Installation Modesty Panel Installation
1 1
2
2
1. Place wire manager underneath worksurface where desired.
2. Attach with three (3) screws.
NOTE: Wire manager can be mounted with the opening towards the user or away from the user.
1. Place modesty panel hole through bracket bolt.
2. Fasten with nut and washer.
3. Position modesty panel and bracket to underside of worksurface. Align modesty panel bracket with edge of table as shown (3a) and attach bracket to underside of worksurface using four (4) screws (3b).
Flush
ModestyPanel
Prior to May 2007
Worksurface
®
3b
3a
