˜fill fine grout fine grout_0320_R… · ISO 13007 – 4 Clause 4.2 : after 240 min : ≤ 10 g...
2
CEMENT-BASED (UNSANDED) FINE COLOURED GROUT fill fine grout DESCRIPTION : fill fine grout has variance of colour, water resistant, fine (unsanded) cement-based grout complies to ISO 13007 – 3 for Class CG1 cement-based grout. Manufactured to stringent Internal Quality Assurance System, conforming to ISO 9001 : 2008. USAGE : fill fine grout is suitable for grouting or pointing joints between Ceramic Wall & Floor Tiles, Vitrified Homogeneous Tiles, Porcelain Tiles, Mosaics, Quarry Tiles, Terracotta, Marbles, Granites, Slates, Terrazzo, Brick Veneer, Decorative Stones etc. Suitable for use at wall or floor, dry or wet, interior or exterior areas including swimming pools. GENERAL PERFORMANCE : The set grout is durable, compressible and water resistant but not impervious to water. fill fine grout is suitable for grouting or pointing joints up to 3 mm wide only. It will not scratch highly glazed ceramic tile surface. requires mixing with Clean Water only. However can also be used with mix GT mix 1, a liquid emulsion polymer, to enhance its physical properties ie. impart flexibility, improve adhesion, reduce water permeability, increase durability, minimizes algae or mould growth & minimizes efflorescence. Note : • For joints wider than 3 mm use fill F&W grout. • Colour variation or cracking may occur with Coloured Grout due to reasons beyond manufacturers control ie. excessive water in mixing and cleaning, condition of mixing water, finishing techniques, site condition, mode of mixing & application, tile porosity variation, efflorescence etc. TYPICAL USE : fill fine grout + WATER : Internal Dry Areas, Intermittent Wet Areas and Sound Substrate. fill fine grout + mix GT mix 1 : • External wall & floor areas • Wet duty areas eg. communal & domestic showers, toilets, washroom, wet kitchen, ablution etc. • Areas or substrate subjected to movement or deflection eg. building boards etc. • Heavy traffic floor areas. • Swimming pool & pool deck APPLICATION PROCEDURE : • During tiling, allocate minimum joints of 2 mm wide for wall tiling & 3 mm wide for floor tiling. • Allow adhesive bed to set 24 hours before grouting commences. • Ensure that joints are dry, clean or free of contaminants. • Mix fill fine grout with clean water (or mix GT mix 1) as per the recommended mix ratio. • Mechanical mixing is recommended to obtain a uniform coloured mortar. Ensure pigments are thoroughly dispersed during mixing. • Apply grout into joints using a grout float / rubber squeegee, ensuring joints are fully compacted with grouting mortar. • Apply to small areas at a time; and clean excess or residue grout promptly using a damp cloth or sponge; before it dries out. • When grout is sufficiently firm, polish tile surface with a clean dry cloth to remove grout film / haze. • Allow grout to set for 24 – 48 hours. TECHNICAL DATA Colour : Refer Colour Chart Density : 1.68 g/cm³ pH of mix : 10.80 Dry Solid Content : 100% Shelf Life : 12 months Inflammability : No Toxicity Hazard : No Bed Thickness : Up to 3mm wide Mix Proportion : 1 pbw water to 2.5 pbw grout (8 ltrs water / Latex Admixture to 20 kg fill fine grout) Working Time (Pot Life) : 45 minutes Setting Time : 24 hours Application Temperature : Above 5°C – 50°C Temperature Resistance : 100°C Frost Resistance : - 15°C Resistance to acids : Fair Resistance to alkalis : Good Resistance to oil & solvents : Fair Damp Resistance : Good Flexibility : Fair Water Absorption : after 30 min : ≤ 5 g ISO 13007 – 4 Clause 4.2 : after 240 min : ≤ 10 g Shrinkage ISO 13007 – 4 Clause 4.3 : ≥ 3 mm/m Flexural Strength : ≥ 5.00 N/mm² Compressive Strength : ≥ 20.0 N/mm² Tensile Bonding Strength : ≥ 0.50 N/mm² TILE GROUT 0320-REV03
Transcript of ˜fill fine grout fine grout_0320_R… · ISO 13007 – 4 Clause 4.2 : after 240 min : ≤ 10 g...
CEMENT-BASED (UNSANDED) FINE COLOURED GROUT
�fill fine grout
DESCRIPTION :�fill fine grout has variance of colour, water resistant, fine (unsanded) cement-based grout complies to ISO 13007 – 3 for Class CG1 cement-based grout. Manufactured to stringent Internal Quality Assurance System, conforming to ISO 9001 : 2008.
USAGE :�fill fine grout is suitable for grouting or pointing joints between Ceramic Wall & Floor Tiles, Vitrified Homogeneous Tiles, Porcelain Tiles, Mosaics, Quarry Tiles, Terracotta, Marbles, Granites, Slates, Terrazzo, Brick Veneer, Decorative Stones etc. Suitable for use at wall or floor, dry or wet, interior or exterior areas including swimming pools.
GENERAL PERFORMANCE : The set grout is durable, compressible and water resistant but not impervious to water. �fill fine grout is suitable for grouting or pointing joints up to 3 mm wide only. It will not scratch highly glazed ceramic tile surface. requires mixing with Clean Water only. However can also be used with �mix GT mix 1, a liquid emulsion polymer, to enhance its physical properties ie. impart flexibility, improve adhesion, reduce water permeability, increase durability, minimizes algae or mould growth & minimizes efflorescence.
Note :• For joints wider than 3 mm use �fill F&W grout. • Colour variation or cracking may occur with Coloured Grout due to reasons beyond manufacturers control ie. excessive water in mixing and cleaning, condition of mixing water, finishing techniques, site condition, mode of mixing & application, tile porosity variation, efflorescence etc.
TYPICAL USE :�fill fine grout + WATER :Internal Dry Areas, Intermittent Wet Areas and Sound Substrate.
�fill fine grout + �mix GT mix 1 :• External wall & floor areas• Wet duty areas eg. communal & domestic showers, toilets, washroom, wet kitchen, ablution etc. • Areas or substrate subjected to movement or deflection eg. building boards etc.• Heavy traffic floor areas.• Swimming pool & pool deck
APPLICATION PROCEDURE :• During tiling, allocate minimum joints of 2 mm wide for wall tiling & 3 mm wide for floor tiling. • Allow adhesive bed to set 24 hours before grouting commences. • Ensure that joints are dry, clean or free of contaminants. • Mix �fill fine grout with clean water (or �mix GT mix 1) as per the recommended mix ratio. • Mechanical mixing is recommended to obtain a uniform coloured mortar. Ensure pigments are thoroughly dispersed during mixing. • Apply grout into joints using a grout float / rubber squeegee, ensuring joints are fully compacted with grouting mortar. • Apply to small areas at a time; and clean excess or residue grout promptly using a damp cloth or sponge; before it dries out. • When grout is sufficiently firm, polish tile surface with a clean dry cloth to remove grout film / haze. • Allow grout to set for 24 – 48 hours.
TECHNICAL DATA
Colour : Refer Colour Chart
Density : 1.68 g/cm³
pH of mix : 10.80
Dry Solid Content : 100%
Shelf Life : 12 months
Inflammability : No
Toxicity Hazard : No
Bed Thickness : Up to 3mm wideMix Proportion : 1 pbw water to 2.5 pbw grout (8 ltrs water / Latex Admixture to 20 kg �fill fine grout)Working Time (Pot Life) : 45 minutesSetting Time : 24 hoursApplication Temperature : Above 5°C – 50°C
Temperature Resistance : 100°CFrost Resistance : - 15°CResistance to acids : FairResistance to alkalis : GoodResistance to oil & solvents : FairDamp Resistance : GoodFlexibility : Fair
Water Absorption : after 30 min : ≤ 5 gISO 13007 – 4 Clause 4.2 : after 240 min : ≤ 10 g
ShrinkageISO 13007 – 4 Clause 4.3 : ≥ 3 mm/m
Flexural Strength : ≥ 5.00 N/mm²
Compressive Strength : ≥ 20.0 N/mm²
Tensile Bonding Strength : ≥ 0.50 N/mm²
T I L E G R O U T 0320-REV03
Note :• Colour pigments in colooured grout may stain or discolor certain tiles or natural stone slabs; therefore a trial should be conducted to determine ease of cleaning and compatibility, before actual application commences. • Certain colours may not be stable when expose to external conditions, please contact our Technical Advisory Department when making colour selection. • Coloured pigmented products may discolour and / or form efflorescence under external weather conditions in time; which is a natural phenomenon. • It is the responsibility of users / applicators to determine suitability of grout; prior to actual application.
APPLICATION :Tile Size Joint Width Approx. Coverage
Mosaics & Wall Tiles :51 x 51 x 5.0 mm 3 mm 1.00 kg / m²108 x 108 x 4.0 mm 2 mm 0.25 kg / m²150 x 150 x 5.5 mm 2 mm 0.25 kg / m²150 x 200 x 6.5 mm 3 mm 0.39 kg / m²200 x 200 x 6.5 mm 3 mm 0.33 kg / m²
Floor Tiles : 108 x 108 x 7.5 mm 3 mm 0.70 kg / m²108 x 150 x 7.5 mm 3 mm 0.60 kg / m²150 x 150 x 7.5 mm 3 mm 0.50 kg / m²200 x 200 x 7.5 mm 3 mm 0.38 kg / m²300 x 300 x 8.0 mm 3 mm 0.27 kg / m²
PACKING :Available in 3.5 kg & 20 kg bags.
SHELF LIFE / STORAGE :At least 6 months; when stored in dry conditions of normal ambient temperature.
TECHNICAL SERVICES :For further details or recommendations please contact our Technical Advisory/Specification Center at 603-6038 9498 (KL) & 604-626 2830 (Penang)
PRECAUTION :Avoid inhaling dust. If material enter eyes, wash out immediately with Clean Water. May cause minor skin irritation; therefore use suitable gloves. Keep out of children reach.
Conditions Of Sales :Sold subject to Company’s Condition of Sale, which is available upon request.
Note :All instruction and information are provided by us for the general guidance only and are believed to be accurate and complete. Users must exercise special care and caution depending on the conditions and particular purpose of usage and are responsible to ensure that they have consulted our latest literature. To the maximum extent allowed by law, Saint-Gobain Weber (M) Sdn Bhd, its representatives, agents or distributors shall be under no liability for any loss of profits and other economic or physical losses.
Marketing Offices :SAINT-GOBAIN WEBER (M) SDN BHD (169772-A)
SELANGOR :No. 29 & 31, Jalan TIAJ 2/1, Taman Industri Alam Jaya,42300 Bandar Puncak Alam, Selangor D. E, Malaysia.Tel : 603-6038 9498 / 9497 / 9487 Fax : 603-6038 9507 Website : www.mys.weberE-Mail : [email protected]
PENANG :No. 8, Lintang Beringin 2, Jalan Permatang Damar LautDiamond Valley Light Industrial Park,11960 Bayan Lepas Penang, Malaysia.Tel : 604-626 2830 / 2829 Fax : 604-626 2106
T I L E G R O U T
Member Of : • FMM, Malaysia • MCIG, Malaysia • MBAM, Malaysia •• MGBC (Malaysia Green Building Confederation)
SGBC (Singapore Green Building Council) •
SIRIM Working Group - MS 1294 & MS 1295
OHSMS CERTIFIED TO ISO 45001 (CERT NO: MY16 / 02151)EMS CERTIFIED TO ISO 14001 (CERT NO: MY13 / 04546)QMS CERTIFIED TO ISO 9001 (CERT NO: CI / 3693)
