本体id11 - NIIGATA€¦ · MD-S7000 series 03 MD-S7000 series 04 Item Unit MD55S7000 MD110S7000...

MD-S7000All Electric Injection Molding Machine

NIIGATA MACHINE TECHNO CO., LTD.

MD-S7000 series 01

MD-S7000 series

Tough ComMachine

Note: Speci�cations are subject to change due to continual improvements.

Compact PrecisionAll Electric InjectionMolding Machine

NiigataHiper Navi

Appropriate PressureTransmission

Reduction of Short Shot & Flash by BPF®

(Balance Pressure Filling)

Less-load & High-precision

Clamping DeviceM Support System for

Effective Clamping (PATENT)

Compact Machinefor Limited Space

Space Saving & Low-heightMachine

Improvement in SetupEf�ciency

Shorter Time for Setup with Quick, Easy and Safe Operation

Ultralow-speed & High-precision Injection

with Suf�cient High Pressure

Hyperslow & High-performancePressure Feedback Control

User-friendlyOperation Screen

Reduced Number of Switchingwith New operation concept

MD-S7000 series 02

MD-S7000 series 03 MD-S7000 series 04

Item UnitMD55S7000 MD110S7000 MD150S7000

Standard High Capacity (OP.) Low Capacity (OP.) Standard High Capacity (OP.) Low Capacity (OP.) Standard

Injection Unit

Standard

Injection Capacity *1 T.m i 1.0 i 1.7a (OP.) i 1.7b (OP.) i 2.7 i 4.0 (OP.) i 2.7 (OP.) i 4.0

Screw CompleteType ― Y (OP.) A B Y A Y A B YY (OP.) Y A B Y A B YY (OP.) Y A B YY (OP.) Y A B

Diameter mm 18 25 30 25 30 25 30 35 25 30 35 40 35 40 45 25 30 35 40 30 35 40 45inch 0.71 0.98 1.18 0.98 1.18 0.98 1.18 1.38 0.98 1.18 1.38 1.57 1.38 1.57 1.77 0.98 1.18 1.38 1.57 1.18 1.38 1.57 1.77

Screw Stroke mm 85 100 120 100 120 100 120 140 100 120 140 160 140 160 180 100 120 140 160 120 140 160 180inch 3.35 3.94 4.72 3.94 4.72 3.94 4.72 5.51 3.94 4.72 5.51 6.30 5.51 6.30 7.09 3.94 4.72 5.51 6.30 4.72 5.51 6.30 7.09

Calculated Injection Volume *2 cm3 22 49 85 49 85 49 85 135 49 85 135 201 135 201 286 49 85 135 201 85 135 201 286cu-inch 1.34 2.99 5.19 2.99 5.19 2.99 5.19 8.24 2.99 5.19 8.24 12.27 8.24 12.27 17.45 2.99 5.19 8.24 12.27 5.19 8.24 12.27 17.45

Calculated Injection Capacity *3 g 20 45 78 45 78 45 78 124 45 78 124 185 124 185 263 45 78 124 185 78 124 185 263oz 0.71 1.59 2.75 1.59 2.75 1.59 2.75 4.37 1.59 2.75 4.37 6.53 4.37 6.53 9.28 1.59 2.75 4.37 6.53 2.75 4.37 6.53 9.28

Max. Injection Pressure *4 Mpa 280 200 140 280 200 280 200 150 280 270 200 155 260 200 155 280 270 200 155 270 260 200 155psi 40,610 29,010 20,310 40,610 29,010 40,610 29,010 21,760 40,610 39,160 29,010 22,480 37,710 29,010 22,480 40,610 39,160 29,010 22,480 39,160 37,710 29,010 22,480

Max. Hold Pressure *4 Mpa 280 180 125 260 180 260 180 135 260 245 180 135 235 180 140 260 245 180 135 245 235 180 140psi 40,610 26,110 18,130 37,710 26,110 37,710 26,110 19,580 37,710 35,530 26,110 19,580 34,080 26,110 20,310 37,710 35,530 26,110 19,580 35,530 34,080 26,110 20,310

Max Injection Speed *5 mm/s 350 300 300 300 300 300 300inch/s 13.78 11.81 11.81 11.81 11.81 11.81 11.81

Injection Rate cm3/s 89 172 247 147 212 147 212 289 147 212 289 377 289 377 477 147 212 289 377 212 289 377 477cu-inch/s 5.43 10.50 15.07 8.97 12.94 8.97 12.94 17.64 8.97 12.94 17.64 23.01 17.64 23.01 29.11 8.97 12.94 17.64 23.01 12.94 17.64 23.01 29.11

Plasticizing Capacity (PS) *6 kg/h 9 27 43 27 43 27 43 60 27 43 60 93 60 93 115 27 43 60 93 43 60 93 115oz/s 0.09 0.26 0.42 0.26 0.42 0.26 0.42 0.59 0.26 0.42 0.59 0.91 0.59 0.91 1.13 0.26 0.42 0.59 0.91 0.42 0.59 0.91 1.13

LP specification

Injection Capacity *1 T.m i 1.0LP (OP.) ― ― i 2.7LP (OP.) i 4.0LP (OP.) i 2.7LP (OP.) i 4.0LP (OP.)

Screw CompleteType ― Y (OP.) A B YY (OP.) Y A B Y A B YY (OP.) Y A B YY (OP.) Y A B

Diameter mm 18 25 30 25 30 35 40 35 40 45 25 30 35 40 30 35 40 45inch 0.71 0.98 1.18 0.98 1.18 1.38 1.57 1.38 1.57 1.77 0.98 1.18 1.38 1.57 1.18 1.38 1.57 1.77

Screw Stroke mm 85 100 120 100 120 140 160 140 160 180 100 120 140 160 120 140 160 180inch 3.35 3.94 4.72 3.94 4.72 5.51 6.30 5.51 6.30 7.09 3.94 4.72 5.51 6.30 4.72 5.51 6.30 7.09

Calculated Injection Volume *2 cm3 22 49 85 49 85 135 201 135 201 286 49 85 135 201 85 135 201 286cu-in 1.34 2.99 5.19 2.99 5.19 8.24 12.27 8.24 12.27 17.45 2.99 5.19 8.24 12.27 5.19 8.24 12.27 17.45

Calculated Injection Capacity *3 g 20 45 78 45 78 124 185 124 185 263 45 78 124 185 78 124 185 263oz 0.71 1.59 2.75 1.59 2.75 4.37 6.53 4.37 6.53 9.28 1.59 2.75 4.37 6.53 2.75 4.37 6.53 9.28

Max. Injection Pressure *4 Mpa 280 200 140 280 270 200 155 260 200 155 280 270 200 155 270 260 200 155psi 40,610 29,010 20,310 40,610 39,160 29,010 22,480 37,710 29,010 22,480 40,610 39,160 29,010 22,480 39,160 37,710 29,010 22,480

Max. Hold Pressure *4 Mpa 280 180 125 260 245 180 135 235 180 140 260 245 180 135 245 235 180 140psi 40,610 26,110 18,130 37,710 35,530 26,110 19,580 34,080 26,110 20,310 37,710 35,530 26,110 19,580 35,530 34,080 26,110 20,310

Max. Injection Speed *5 mm/s 250 230 200 230 200inch/s 9.84 9.06 7.87 9.06 7.87

Injection Rate cm3/s 64 123 177 113 163 221 289 192 251 318 113 163 221 289 141 192 251 318cu-inch/s 3.91 7.51 10.80 6.90 9.95 13.49 17.64 11.72 15.32 19.41 6.90 9.95 13.49 17.64 8.60 11.72 15.32 19.41

Plasticizing Capacity （PS） *6 kg/h 9 27 43 27 43 60 93 60 93 115 27 43 60 93 43 60 93 115oz/s 0.09 0.26 0.42 0.26 0.42 0.59 0.91 0.59 0.91 1.13 0.26 0.42 0.59 0.91 0.42 0.59 0.91 1.13

High-speedspecification

Injection Capacity *1 T.m i 1.0H (OP.) ― ― i 2.7H (OP.) ― i 2.7H (OP.) ―

Screw CompleteType ― Y (OP.) A YY (OP.) Y A YY (OP.) Y A

Diameter mm 18 25 25 30 35 25 30 35inch 0.71 0.98 0.98 1.18 1.38 0.98 1.18 1.38

Screw Stroke mm 85 100 100 120 140 100 120 140inch 3.35 3.94 3.94 4.72 5.51 3.94 4.72 5.51

Calculated Injection Volume *2 cm3 22 49 49 85 135 49 85 135cu-in 1.34 2.99 2.99 5.19 8.24 2.99 5.19 8.24

Calculated Injection Capacity *3 g 20 45 45 78 124 45 78 124oz 0.71 1.59 1.59 2.75 4.37 1.59 2.75 4.37

Max. Injection Pressure *4 Mpa 280 200 280 270 200 280 270 200psi 40,610 29,010 40,610 39,160 29,010 40,610 39,160 29,010

Max. Hold Pressure *4 Mpa 280 180 260 245 180 260 245 180psi 40,610 26,110 37,710 35,530 26,110 37,710 35,530 26,110

Max. Injection Speed *5 mm/s 500 500 500inch/s 19.69 19.69 19.69

Injection Rate cm3/s 127 245 245 353 481 245 353 481cu-inch/s 7.76 14.98 14.98 21.57 29.36 14.98 21.57 29.36

Plasticizing Capacity (PS) *6 kg/h 9 27 27 43 60 27 43 60oz/s 0.09 0.26 0.26 0.42 0.59 0.26 0.42 0.59

Nozzle Stroke mm (inch) 325 (12.80) 370 (14.57) 370 (14.57)Nozzle Touch Force kN (US t) 20/14 (2.25/1.58) 20/14 (2.25/1.58) 20/14 (2.25/1.58)Screw Rotation Speed min-1 360 360 360

Temp. ZonesNozzle Heating Cylinder ― 1G+4 1G+4 1G+4Hopper Base ― 1 1 1

Heater Capacity kW 2.8 5.0 8.0 5.0 8.0 2.8 5.0 8.0 5.0 8.0 10.7 12.1 10.7 12.1 14.1 5.0 8 10.7 12.1 8.0 10.7 12.1 14.1

Clamping Unit

Clamping System ― Double Toggle Double Toggle Double ToggleClamping Force kN (US t) 500 (56) 1,000 (112) 1,300 (146)Tie-Bar Distance (H x V) mm (inch) 360 (14.17) × 320 (12.60) 460 (18.11) × 410 (16.14) 510 (20.08) × 460 (18.11)Platen Size (H x V) mm (inch) 510 (20.08) × 470 (18.50) 610 (24.02) × 610 (24.02) 670 (26.38) × 670 (26.38)Mold Opening Stroke mm (inch) 250 (9.84) 350 (13.78) 380 (14.96)Mold Height (Min/Max) mm (inch) 160/370 (6.30/14.57) 200/450 (7.87/17.72) 200/450 (7.87/17.72)Open Daylight mm (inch) 620 (24.41) 800 (31.50) 830 (32.68)Ejector Stroke mm (inch) 70 (2.76) 100 (3.94) 100 (3.94)Ejector Force kN (US t) 22 (2.47) 32 (3.60) 32 (3.60)

Utility

Total Machine Power *7 kVA 14 29 29

Power Source(Voltage x Frequency) *8 ― AC200V (±10%) × 50Hz/AC200V (±10%) × 60Hz AC200V (±10%) × 50Hz/AC200V (±10%) × 60Hz AC200V (±10%) × 50Hz/AC200V (±10%) × 60Hz― AC220V (±10%) × 60Hz AC220V (±10%) × 60Hz AC220V (±10%) × 60Hz

Cable Size *9 mm2 (A.W.G) 8 (8 A.W.G) 22 (4 A.W.G) 22 (4 A.W.G)Machine Mass ton (US t) 2.7 (2.97) 4.8 (5.28) 5.9 (6.49)Hopper Size (OP) L (gal) 15 (3.96) 45 (11.89) 45 (11.89)Cooling Water Consumption (Max) *10 L/min (gal/min) 5 (1.32) 5 (1.32) 7.5 (1.98)

● Note: Specifications are subject to change without notice. Items with (OP.) are optional.

*1 Injection Capacity is expressed in T.m, calucalated by (Max. Injection Pressure) x (Calculated Injection Volume).*2 Calculated Injection Volume is calculated by multiplying screw cross sectional area and Screw Stroke.*3 Calculated Injection Capacity is a shot mass of polystyrene with 92% of Calculated Injection Volume.*4 Max. Injection Pressure and Max. Hold Pressure may not reach indicated value depending on cycle condition.*5 Max. Injection Speed may not reach indicated value depending on loaded condition.

MD-S7000Series Specifications

*6 Plasticizing Capacity is in case of polystyrene.*7 Total Machine Power is only for machine itself. Additional power is required when connecting

auxiliary equipment.*8 Power supply voltage fluctuation shall be within plus or minus 10% of rated voltage. Voltage

fluctuation shall not occur frequently or for a long time.

*9 Cable size is for single core cable (IV). Apply current reduction coefficient when using multi-core cable.

*10 Cooling water is used for under hopper area. Water pressure shall be 0.5 MPa or less.


Item Unit MD200S7000 MD310S7000 MD385S7000 MD500S7000

Injection Unit

Standard Specification

Injection Capacity *1 T.m i 6.5 i 10 i 15 i 32

Screw CompleteType - Y (OP.) A B Y (OP.) A B Y (OP.) A B A B

Diameter mm 40 45 52 45 52 60 52 60 68 76 82in 1.57 1.77 2.05 1.77 2.05 2.36 2.05 2.36 2.68 2.99 3.23

Screw Stroke mm 205 240 270 350in 8.07 9.45 10.63 13.78

Calculated Injection Volume *2 cm3 258 326 435 382 510 679 573 763 980 1588 1848cu-in 15.74 19.89 26.55 23.29 31.12 41.44 34.99 46.56 59.80 96.91 112.77

Calculated Injection Capacity *3 g 237 300 401 351 469 624 527 702 901 1461 1700oz 8.36 10.58 14.14 12.39 16.54 22.01 18.61 24.76 31.78 51.54 59.97

Max.Injection Pressure *4 MPa 250 200 150 250 200 150 250 200 155 200 170psi 36260 29010 21760 36260 29010 21760 36260 29010 22480 29010 24660

Max.Hold Pressure *4 MPa 225 180 135 225 180 135 225 180 140 180 155psi 32630 26110 19580 32630 26110 19580 32630 26110 20310 26110 22480

Max. Injection Speed *5 mm/s 300 230 200 160in/s 11.81 9.06 7.87 6.30

Injection Rate cm3/s 377 477 637 365 488 650 425 565 726 726 845cu-in/s 23.01 29.11 38.87 22.32 29.78 39.67 25.92 34.48 44.30 44.30 51.56

LP Specification(OP.)

Injection Capacity T.m i 6.5 LP i 10 LP i 15 LP i 22 LP

Screw CompleteType - Y (OP.) A B Y (OP.) A B Y (OP.) A B Y (OP.) A B

Diameter mm 40 45 52 45 52 60 52 60 68 60 68 76in 1.57 1.77 2.05 1.77 2.05 2.36 2.05 2.36 2.68 2.36 2.68 2.99

Screw Stroke mm 205 240 270 305in 8.07 9.45 10.63 12.01

Calculated Injection Volume *2 cm3 258 326 435 382 510 679 573 753 981 862 1108 1384cu-in 15.74 19.89 26.55 23.29 31.12 41.44 35.00 46.56 59.86 52.60 67.61 84.46

Calculated Injection Capacity *3 g 237 300 401 351 469 624 527 702 902 793 1019 1273oz 8.36 10.58 14.14 12.39 16.54 22.01 18.59 24.76 31.81 27.97 35.94 44.90

Max.Injection Pressure *4 MPa 250 200 150 250 200 150 250 200 155 250 200 160psi 36260 29010 21760 36260 29010 21760 36260 29010 22480 36260 29010 23210

Max.Hold Pressure *4 MPa 225 180 135 225 180 135 225 180 140 225 180 145psi 32630 26110 19580 32630 26110 19580 32630 26110 20310 32630 26110 21030

Max. Injection Speed *5 mm/s 240 200 160 160in/s 9.45 7.87 6.30 6.30

Injection Rate cm3/s 302 382 510 318 425 565 340 452 581 452 581 726cu-in/s 18.43 23.31 31.12 19.41 25.94 34.48 20.74 27.58 35.45 27.60 35.45 44.30

Screw Rotation Speed mm-1 400 400 300 240 200

Plasticizing Capacity (PS) *6 kg/h 113 148 228 148 201 274 151 206 315 165 252 315 256 269oz/s 1.11 1.45 2.23 1.45 1.97 2.68 1.48 2.02 3.09 1.62 2.47 3.09 2.51 2.93

Nozzle Stroke mm 410 435 450 450 560in 16.14 17.13 17.72 17.72 22.05

Nozzle Touch Force kN 34 / 23.8 34 / 23.8 34 / 23.8 34 / 23.8 36.3US ton 3.82 / 2.67 3.82 / 2.67 3.82 / 2.67 3.82 / 2.67 4.08

Temperature Zones Nozzle Heating Cylinder - 1G+2+1G 1G+2+1G 1G+2+1G 1G+2+1G 1G+3+1GHopper Base - 1 1 1 1 1Heater Capacity kW 11.49 14.2 14.69 18.7 18.7 20.9 21.5 25.06 33.2

Clamping Unit

Clamping System - Double toggle Double toggle Double toggle Double toggle

Clamping Force kN 1800 2800 3500 4500US ton 202 315 393 506

Tie-Bar Distance (H × V) mm 590 x 530 730 x 730 810 x 810 910 x 810in 23.23 x 20.87 28.74 x 28.74 31.89 x 31.89 35.83 x 31.89

Platen Size (H x V) mm 770 x 770 930 x 930 1040 x 1040 1160 x 1160in 30.31 x 30.31 36.61 x 36.61 40.94 x 40.94 45.67 x 45.67

Mold Opening Stroke mm 450 600 650 800in 17.72 23.62 25.59 31.5

Mold Height (Min. /Max.) mm 200 / 600 320 / 720 320 / 780 380 / 910in 7.87 / 23.52 12.60 / 28.35 12.60 / 30.71 14.96 / 35.83

Open Daylight mm 1050 1320 1430 1710in 41.34 51.97 56.30 67.32

Ejector Stroke mm 110 150 150 160in 4.33 5.91 5.91 6.3

Ejector Force kN 45 60 78 80US ton 5.06 6.74 8.77 8.99

Others

Total Machine Power *7 kVA 36 36 43 87Power Source (Voltage x Frequency) *8 - AC200V ( ± 10%) x 50Hz/AC200V ( ± 10%) x 60Hz

AC220V ( ± 10%) x 60HzAC200V ( ± 10%) x 50 Hz/AC200V ( ± 10%) x 60Hz

AC220V　　( ± 10%) x 60HzAC200V ( ± 10%) x 50Hz/AC200V ( ± 10%) x 60Hz

AC220V ( ± 10%) x 60HzAC460V ( ± 10%) x 60HzAC480V ( ± 10%) x 60Hz

Cable Size *9 mm2 30 30 38 125A.W.G. 3 3 1 5/0

Machine Size

Width m 5.19 6.14 6.79 8.09in 204.5 241.8 267.2 318.54

Depth m 1.53 1.74 1.89 2.06in 60.2 68.5 74.2 80.94

Height m 1.95 2.11 2.06 2.19in 76.7 83.0 81.1 86.26

Machine Mass ton 8.6 14.5 17.0 26.0 US ton 9.5 16.0 18.7 28.6

Hopper Size (OP) L 45 80 80 120gal 11.89 21.13 21.13 31.70

Cooling Water Consumption (Max) *10 L/min 7.5 7.5 7.5 10gal/min 1.98 1.98 1.98 2.64

MD-S7000Series Specifications

● Note : Specifications are subject to change without notice. Items with (OP.) are optional.

*1 Injection Capacity is expressed in T.m, calucalated by (Max. Injection Pressure) x (Calculated Injection Volume).*2 Calculated Injection Volume is calculated by multiplying screw cross sectional area and Screw Stroke.*3 Calculated Injection Capacity is a shot mass of polystyrene with 92% of Calculated Injection Volume.*4 Max. Injection Pressure and Max. Hold Pressure may not reach indicated value depending on cycle condition.*5 Max. Injection Speed may not reach indicated value depending on loaded condition.

*9 Cable size is for single core cable (IV). Apply current reduction coefficient when using multi-core cable.

*10 Cooling water is used for under hopper area. Water pressure shall be 0.5 MPa or less.

*6 Plasticizing Capacity is in case of polystyrene.*7 Total Machine Power is only for machine itself. Additional power is required when connecting

auxiliary equipment.*8 Power supply voltage fluctuation shall be within plus or minus 10% of rated voltage. Voltage

fluctuation shall not occur frequently or for a long time.


External Dimension Diagram（MD55S7000）



External Dimension Diagram（MD310S7000） External Dimension Diagram（MD385S7000）


External Dimension Diagram（MD500S7000） Standard accessories & functions

General

1. Operation mode (adjust, manual, semi-automatic, full-automatic, purge)2. Automatic lubrication3. Emergency stop button with lock4. Sourcing type control circuit (PNP)

Injection

1. Multistage injection control1) Injection speed control : max. 10 speeds,　Filling pressures for each speed stage2) Injection pressure control : max. 10 speeds, Holding speeds for each pressure stage

2. Low friction injection mechanism (Linear guide type) (50t, 100t, 130t machines only)3. Balance Pressure Filling control 4. Constant Pressure Filling control5. Sealed ball screw6. Multistage charging control :3 speeds, 3 back pressures7. Automatic purge (4 modes)8. Nozzle temperature group control 9. Cylinder follow-up temperature control for nozzle zone

10. PID fuzzy control ｌ ed temperature regulation of heating cylinder11. Cold screw starting prevention12. Double-layer structure cylinder heater cover13. Charging under no back pressure in manual mode14. Hopper base temperature control (PID)15. Purge guard (with interlock)16. Nozzle retract (retract time setting)17. Delay timers for injection, Charging, Nozzle retract18. Digital load cell device (High-precision detection of injection pressure and back pressure)19. Anti wearing screw cylinder

Clamping

1. Highly rigid clamping mechanism (M Support System) (50t, 100t, 130t machines only)2. Multistage speed control device (up to 6 speeds)3. Simplified setup device (Mold setting mode, Clamping force adjusting mode,

Low pressure mold protection adjusting mode)4. Automatic clamping force setting5. Mold height adjust device with encoder6. Clamping force monitor7. Low pressure mold protection8. All processes mold protection device9. Ejector advance position holding timer

10. Ejector advance speed switching (2 speeds)11. Ejector motor with brake12. Mold closing safety device on the operator's side (mechanical & electrical)13. Mold closing safety device on the opposite side (mechanical & electrical)14. Hole processing of mounting hole for take-out robot （in our standard position）15. Delay timers for ejector 16. Pre-releasing of clamping force17. Low pressure clamping force holding

Control

1. 12.1 inch color LCD touch panel2. NHN (Niigata Hiper Navi) Operation support, simplified setup device, easy setting function3. Simultaneous operation

1) Mold open during charging 2) Ejector on the fly3) Nozzle advance during mold close4) Injection start during mold close5) Output signal of take-out robot's entry during mold open

4. Servo motor with high-resolution encoder5. Expert function (Setting conversion from other machines)6. Calendar timer for heater start-up 7. Multiple language (Japanese, English, Chinese, Spanish or Korean) 8. Molding condition recording (384 in built-in memory, 384 in external memory)9. Recording of trial molding condition (10 conditions)

10. Motion/No-motion selector switch11. Cylinder follow-up temperature control for nozzle zone12. Operation selector switch during alarm activation13. Alarm buzzer14. No-fuse breaker for main power supply15. Take-out robot interface circuit16. External memory interface (USB I/F)17. Event record (record of injection condition, temperature condition, clamping condition,

activation of alarm and machine abnormality: 1,000 records respectively)

Control

18. Instruction manual display19. Convenient functions (notepad, calculator etc.)20. Maintenance information21. Local password21. Output of external signal (multiple-choice)

Alarms・

Counters・

Monitors

1. Alarm device1) Automatic lubrication alarm2) Servo motor alarm3) Motor thermal alarm (nozzle / mold height)4) V-P transfer alarm (Timer/Position/Pressure, upper/lower limit)5) Charging time alarm (upper/lower limit)6) Cycle time alarm (upper limit)7) Cylinder temperature alarm (upper/lower limit)8) Hopper base temperature alarm (upper/lower limit)9) Heater break alarm10) SSR alarm11) Thermo couple break alarm12) Temperature regulator preparation alarm13) Resin lack alarm14) Clamping alarm15) Cushion position (min. / finish) alarm (upper/lower limit)16) Peak pressure alarm (during filling/injection, upper/lower limit)17) Screw operation prohibition alarm18) Low-pressure mold protection alarm19) Injection unit alarm20) Injection start position alarm (upper/lower limit)21) Operator's gate alarm22) Grease lubrication alarm23) Monitoring alarm for screw position (arrival time, injection pressure)24) Resin retention monitoring alarm

2. Counter device1) Total shot counter (preset type)2) Production shot counter (preset type)3) Preparation shot counter (preset type)4) Shot counter for external conveyer (preset type)5) Reject shot counter (preset type)6) Continuous reject shot counter (preset type)

3. Shot monitor (10000 shots)1) Cycle time2) Injection starting position3) Cushion position (min./finish)4) Filling peak pressure5) Injection peak pressure6) V-P transfer time7) V-P transfer position8) V-P transfer pressure9) Arrival time at the setting point10) Injection pressure at the setting point11) Charging time12) Nozzle (N1, N2) temperature13) Cylinder 1, 2, 3, 4 temperature14) Hopper base temperature15) Power consumption in one cycle

4. Graphical monitor (Injection, mold open/close, ejector, screw rotation etc.) Overwriting, simultaneous display of max. 8 waveforms, Data reading function from the graphics

5. Servo motor monitor6. Statistical processing of monitoring data7. History monitor (record of temperature range inside of control box,

accumulated running distance of ball screw, shot count etc.)8. Ladder monitor9. Power consumption monitoring device

Others

1. Safety compliance: ANSI/Plastics B151.1.1-20172. Leveling pads3. Mold mounting kit (8 sets)4. Spare grease cartridge (for Automatic lubrication 700cc : 1 pc)5. Special tools

1. Anti wearing screw cylinder 10. Outlet 200V (20A, 30A) 19. Mold temperature regulator2. Special design screw 11. Outlet 100V 20. Earth leakage breaker3. Ejector compression system (ECS) 12. Specified color 21. High temperature heater4. Resin hopper 13. Product chute 22. Core puller (with hydraulic / pneumatic unit)5. Optional Nozzle (Long open nozzle, Spring needle nozzle) 14. Special locating ring 23. PC interface6. Heat insulating board (thickness : 5mm,10mm) 15. Interface circuit for product fall detector 24. Flow molding device7. Air jet / Air ejector 16. Product sorting chute (good / reject) 25. Intermediate stop of mold open/close8. Signal tower 17. Signal for hot runner interface 26. Signal for valve gate control9. Mold ejector plate return confirmation device 18. Interface for unscrewing device (motor excluded) 27. Quick Servo Press (QSP)

Optional accessories & functions

NIIGATA MACHINE TECHNO CO., LTD.JAPAN NIIGATA MACHINE TECHNO CO., LTD. 1300 Okayama Higashi-ku Niigata-City

Niigata-pref, Japan

TEL:+81-25-274-5121 FAX:+81-25-271-5827

SHANGHAI NIIGATA MACHINE TECHNO (SHANGHAI) CO., LTD. 1F-1A, No.2, 1245 Zhong Shan Road West,

Changning District, Shanghai 200051, China

TEL:+86-21-6115-6925 FAX:+86-21-6115-6926

DONGGUAN NIIGATA MACHINE TECHNO (SHANGHAI) CO., LTD DONGGUAN BRANCH

Room 1402, Zheguan Business Center,

No. 286, South Changqing Road, Changan Town,

Dongguan City, Guangdong 523850, China

TEL:+86-769-8275-1918 FAX:+86-769-8275-1928

THAILAND NIIGATA MACHINE TECHNO (THAILAND) CO., LTD. 42 Tower, Unit 1003, 10th Fl., 65 Soi Sukhumvit 42,

Sukhumvit Road, Prakhanong, Klongtoey,

Bangkok 10110, Thailand

TEL:+66-2-012-4272 FAX:+66-2-012-4273

U.S.A. NIIGATA MACHINE TECHNO USA, INC. 1501 Landmeier Road,

Elk Grove Village, IL 60007, U.S.A.

TEL:+1-630-283-5880

18110188

本体id11 - NIIGATA€¦ · MD-S7000 series 03 MD-S7000 series 04 Item Unit MD55S7000 MD110S7000...

Documents

Transcript of 本体id11 - NIIGATA€¦ · MD-S7000 series 03 MD-S7000 series 04 Item Unit MD55S7000 MD110S7000...