OCPS CLAY SPRINGS ES SUBMITTAL TRANSMITTAL · DRAWING AND/OR PRODUCT DATA SUBMITTAL. N ... DPRM Red...

SUBMITTAL NUMBER: 265600-01.00

OCPS CLAY SPRINGS ES SUBMITTAL TRANSMITTAL

SUBMITTAL DETAILS:

REVIEWERS:

SUBJECT: EXTERIOR LIGHTING

DATE RECIEVED: Oct 23, 2014

DISCIPLINE: Electrical

PRIMARY: TAD RIVENBARK

[email protected]

KEVIN KING

[email protected]

MATERN ENGINEERING

PHN: (407) 740-5020

FAX: (407) 740-0365

MATERN ENGINEERING

PHN: (407) 740-5020

FAX: (407) 740-0365

SECONDARY:

PRIORITY STATUS: 2-STANDARD

REVIEWER DUE DATE: 11/4/2014

SPECIFICATION REF: 26 56 00

DWG REF. NONE

DWG TITLE:

NO OF ITEMS: ITEM DESCRIPTI

REVIEW STATUS:

COMMENTS:

CONTRACTOR/CM:

: WILLIAMS COMPANY: BRAD KUBIN 2301 SILVER STAR RD. ORLANDO, FL, 32809 (407) 295-2530 FAX:(407) 297-0459

PLEASE SEE A/E COMMENTS

**"ALL EXTERIOR FIXTURES TO BE CLEAR ANODIZED OR NATURAL ALUMINUM COLOR/FINISH"

FURNISH AS MARKED

RETURNED ITEMS:

DATE RETURNED TO CM: 11/5/2014

BUILDING REFERENCE:

1 Product Literature(s)

PAGE 1 OF 1RHODES + BRITO ARCHITECTS INC. : 605 E. ROBINSON STREET, SUITE 750 : ORLANDO, FL. : 32801 : 407.648.7288 : FAX.648.7289

cc:

OWNER : CALVIN WOOLFOLK 6501 MAGIC WAY, BLDG. 200 ORLANDO, FL, 32809 (407) 317-3700

FAX:(407) 317-3768

R+B FILE: : 13017-0001.X6

michele

Highlight

michele

rICK

101374

Received

of 2

Corporate Office: 130 Candace Drive, Maitland, Florida 32751-3331 Phone: 407.740.5020 Orlando | Fort Myers | Jacksonville | Tampa | www.matern.net

SHOP DRAWING COMMENTS

Date: November 4, 2014 By: Tad Rivenbark Submittal: 26 56 00 – Exterior Lighting

Project: OCPS – Clay Springs E.S. Proj. No: 2013-224

THE FOLLOWING COMMENTS SHALL BE CONSIDERED AN INTEGRAL PART OF THE SHOP DRAWING AND/OR PRODUCT DATA SUBMITTAL.

26 56 00: No Exceptions Noted, Make Corrections Noted.

Note: Ballast quantities and voltages not reviewed. Provide ballasts as necessary to maintain switching arrangements indicated on drawings. H1: Make Corrections Noted. Ballast manufacturer shall be Magnetek, or approved substitution.

Ballast shall be multi-voltage as shown on the Fixture Schedule. Ballasts installed outdoors shall be zero degree ballasts.

Sylvania, G.E., or Phillips shall manufacture lamps. Lamps shall be 4100K.

SLA: Make Corrections Noted. Sylvania, G.E., or Phillips shall manufacture lamps.

Fixture color selection shall be by the Architect. Provide lightning arrester for each pole light. Provide fuse for each pole light.

SLB: Make Corrections Noted. Sylvania, G.E., or Phillips shall manufacture lamps.

Fixture color selection shall be by the Architect. Provide lightning arrester for each pole light. Provide fuse for each pole light.

ACTION CODE KEY

A No exceptions taken. B Make corrections noted. C Revise and Resubmit. D Submit Specified Item. E Rejected. N Review not required.

Shop Drawing Comments - Electrical

Page 2 of 2

Corporate Office: 130 Candace Drive, Maitland, Florida 32751-3331 Phone: 407.740.5020 Orlando | Fort Myers | Jacksonville | Tampa | www.matern.net

SLC: Make Corrections Noted. Fixture color selection shall be by the Architect.

Provide lightning arrester for each pole light. Provide fuse for each pole light. Fixture shall have Type II distribution as shown on the Fixture Schedule.

WMD: Make Corrections Noted. Fixture color selection shall be by the Architect.

Provide fuse for each fixture. Fixture shall have Type II distribution as shown on the Fixture Schedule.

WP1A: Make Corrections Noted. Sylvania, G.E., or Phillips shall manufacture lamps.

Fixture color selection shall be by the Architect. Lightning Arrestor: No Exceptions Noted.

END OF SHOP DRAWING COMMENTS

SUBMITTAL NUMBER: 26560001.00

OCPS CLAY SPRINGS ES SUBMITTAL ASSIGNMENT MEMO

SUBMITTAL DETAILS: REVIEWERS:

SUBJECT: EXTERIOR LIGHTING

DATE RFI RECIEVED: Oct 23, 2014

DISCIPLINE: Electrical

PRIMARY: TAD RIVENBARK

[email protected]

KEVIN KING

[email protected]

MATERN ENGINEERING

PHN: (407) 740-5020FAX: (407) 740-0365

MATERN ENGINEERING

PHN: (407) 740-5020

FAX: (407) 740-0365

SECONDARY:

PRIORITY STATUS: 2-STANDARD

REVIEWER DUE DATE: 11/4/2014

SPECIFICATION REF: 26 56 00

DWG REF. NONE

DWG TITLE:

REVIEW STATUS:

THIS SUBMITTAL IS ISSUED TO YOU FOR YOUR REVIEW. PLEASE RESPOND AND RETURN...WITH THIS COMPLETED SAM TRANSMITTAL...TO MICHELE BUDAY-URDANETA NO LATER THAN: 11/4/2014. PLEASE COMPLETE REVIEW STATUS AT RIGHT

SUBMITTAL CONTENTS:

NO OF ITEMS: ITEM DESCRIPTION

(please print)THIS SUBMITTAL WAS REVIEWED BY :

RE-SUBMIT WITH ITEMS

NOT REVIEWED

REJECTED

REVISE AND RESUBMIT

FURNISHED AS MARKED

REVIEWED

COMMENTS:

1 PRODUCT LITERATURE(S)

cc:

OWNER : CALVIN WOOLFOLK

6501 MAGIC WAY, BLDG. 200

ORLANDO, FL, 32809

R+B FILE: : 13017-0001.X6CONTR/CM: : WILLIAMS COMPANY

: BRAD KUBIN

2301 SILVER STAR RD.

Submittal Cover.doc

ABC ACCREDITED QUALITY CONTRACTOR EC-0000981

430 West Drive Altamonte Springs, Florida 32714 EC-0000981 Phone: (407) 788-3500

CLAY SPRINGS ELEMENTARY SCHOOL

TCE JOB #100707

OWNER: Orange County Public Schools Design & Construction Bldg. 200, 6501 Magic Way Orlando, FL 32809

GENERAL CONTRACTOR: Williams Company 2301 Silver Star Road Orlando, FL 32804

ARCHITECT: Rhodes + Brito Architects 605 E. Robinson Street, Suite 750 Orlando, FL 32801

ENGINEER: Matern Professional Engineering, Inc. 130 Candace Drive Maitland, FL 32751

SUBCONTRACTOR: Tri-City Electrical Contractors, Inc. 430 West Drive Altamonte Springs, FL 32714

Specification Section: 26 56 00 Exterior Lighting (Revised)

10/17/14

katrinae

WCBD - Trent

katrinae

Accepted

trivenbark

Shop Drawings

Submitted by Landreth, Inc.

Job Name: OCPS CLAY SPRINGS ELEMENTARYSCHOOLArchitect: Rhodes+Brito (Orlando)

Catalog Number:SVR-132T8-277V-ISN-GLR

Notes:

Type:

H1LAND14-51183

SVR Series

Nulite Lighting 10770 East 51st Avenue, Denver, CO 80239 Phone 303-287-9646 Fax 303-287-0316 www.nulite-lighting.com

Description:

TM

Project Name:

Type:

Catalog #:

Date:

Construction: Housing is die formed of 20 gauge cold rolled steel. Housing is finished with baked white enamel paint. Clear polycarbonate lens features pyramidal prism bottom and vertical ribbed perimeter provides maximum light control and efficiency. Lens is secured with tamper resistant spanner head screws.

Reflector / Ballast: Ballast cover/pan is formed and finished with high reflectance white paint. Standard electronic, Class P, ballast. Universal (UNV) voltage ballast is from 120 to 277V.

Lamping: 1, 2 or 3 lamp cross-section T5, T5HO or T8. Luminaire can be ordered with lamps, consult factory.

Mounting: Surface.

Labels: UL / cUL listed for Damp location. Wet location is optional.

The Nulite SVR series is a vandal resistant low profile surface mounted lensed luminaire. The polycarbonate prismatic / ribbed lens will hold up to high traffic and vandal applications.

Specifications:

Ordering InformationSample: SVR-232T8-UNV-ISN-WL

Series Wattage Voltage Options

14T524T5HO17T828T554T5HO32T8

UNV

120

277

3473

EM

4Emergency Battery Pack

Lamp

11

2

32

Ballast

Notes: 1. 1-Lamp cross-section is only available in nominal 4’ length.2. 3-Lamp cross-section is only available for 32W T8.3. Consult factory.4. Specific voltage must be ordered for this option. Consult factory for nominal 2’ units.

9-1/2”

3-1/4”

Length Wattage

27” 14T5, 24T5HO, 17T8

51” 28T5, 54T5HO, 32T8

2010 Rev. B

SVR

4-3/4”

4-7/8”

(1-light, nom. 4’ only)

(2 or 3-light, nom. 2’ or 4’)

WL Wet Location

7/8” KO

IS (Standard)Instant Start

PSProgram Start

HEISHigh Efficiency Instant Start

HEPSHigh Efficiency Program Start

N Normal (Standard)

L Low

H High

DIM3 Dimming

SD3 Step Dimming

T8 Options

PS (Standard)Program Start

HEPS3

High Efficiency Program Start

T5/T5HO

All Lamp Dimming Options

Ballast Factor

Ballast Factor

N Normal

Specifications and dimensions are subject to change without notification. Specification sheets on our website supersede all other versions. Nulite reserves the right to bulk package any order.

GLR Fusing

1 32T8 277 IS N GLR



Catalog Number:SVR-132T8-277V-ISN-GLR

Notes:

Type:

H1LAND14-51183

SVR Series

Nulite Lighting 10770 East 51st Avenue, Denver, CO 80239 Phone 303-287-9646 Fax 303-287-0316 www.nulite-lighting.com

TM

Specifications and dimensions are subject to change without notification.

Page 2

Plan view of KOs on back of housing

7/8” KO 2” KO

51”6-1/2”

51”

6-1/2”

27”12-1/8”

4-7/8”

9-1/2”

9-1/2”



Catalog Number:40'OAL/30'MH/10'BURIAL TYPE II/O WITH SECONDRACEWAY IN POLE FOR LIGHTNING PROTECTIONDOWN CONDUSTORNotes:

Type:

SLALAND14-51183



Catalog Number:T20-190

Notes:

Type:

SLALAND14-51183

Catalog Number

Notes Type

FEATURES & SPECIFICATIONSINTENDED USEDrill mount tenon adaptor converts pole-top tenons to accommodate arm-mounted luminaires.CONSTRUCTIONAdaptor is formed from aluminum 6061 alloy schedule 40 pipe, heat-treated to a T6 temper after welding. Welding follows industry-standard best practices.Hardware: Stainless steel set screws included.Top cap: Plastic top cap included.Finish: Must specify finish.INSTALLATIONSlide slipfitter over pole tenon and tighten down set screws. Proceed with arm installation.

NOTES:1 Txx is drill template #5. ASTxx is drill template #8. Special drillings

available; consult factory. 2 Additional custom sizes are available; consult factory.3 Finish must be specified. Additional colors available; see www.

lithonia.com/archcolors or the Architectural Colors brochure (Form No. 794.3).

Drill-Mount Tenon Slipfitter

TXX/ASTXXSTANDARD (TXX) OR AERIS™/OMERO™ (ASTXX)

DRILL PATTERN

Outdoor

(See next page for dimensions and drawings.)

Sheet #: Pole-TXX-ASTXX

Lead times will vary depending on options selected. Consult with your sales representative.Example: T20-280 DDB

ORDERING INFORMATION

Drilling orientation

190 1 at 90° 280 2 at 180° 290 2 at 90° 320 3 at 120° 390 3 at 90° 490 4 at 90°

Drilling and slipfitter size1,2

T20 2-15/32" I.D. T25 3-3/8" I.D. T35 4-1/4" I.D. AST20 2-15/32" I.D. AST25 3-1/16" I.D. AST35 4-3/32" I.D.

Finish3

Standard colors DDB Dark bronze DWH White DBL Black DMB Medium bronze BA Brushed aluminumClassic colors DSS Sandstone DGC Charcoal gray DTG Tennis green DBR Bright red DSB Steel bluePrimer finish DPRM Red primerClass 1 architectural anodized ABL Black ADB Dark bronze ANA NaturalArchitectural colors3

(powder finish)

–T20 190




Notes:

Type:

SLALAND14-51183

Lithonia Lighting OutdoorOne Lithonia Way, Conyers, GA 30012Phone: 770-922-9000 Fax: 770-918-1209www.lithonia.com

Txx/ASTxx Drill-Mount Tenon Slipfitter; Metal, Fiberglass or Concrete Poles

IMPORTANT: • These specifications are intended for general purposes only. Lithonia Light-

ing reserves the right to change material or design, without prior notice, in a continuing effort to upgrade its products.

CAUTION: • The arms described herein are designed for applications in areas of normal

winds. Consult the factory prior to the design of systems to be mounted on structures such as bridges or buildings, or areas known to have abnormal winds such as airports or coastal areas. Failure to consider these factors in the system design could result in the failure of the pole or mast arm, and consequently personal injury or property damage.

© 2010 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/15/10Sheet #: Pole-TXX-ASTXX

Txx-xxx/ASTxx-xxx Drill-Mount Tenon Slipfitter Drilling Lithonia Lighting Template

Dimensions (inches) Catalog Number Pattern A B C D E T20-xxx #5 2.468 2.875 1.750 2.125 4.250 T25-xxx #5 3.062 3.500 1.750 2.125 4.250 T35-xxx #5 4.100 4.574 1.750 2.125 4.250 AST20-xxx #8 2.468 2.875 1.750 1.325 2.650 AST25-xxx #8 3.062 3.500 1.750 1.325 2.650 AST35-xxx #8 4.100 4.574 1.750 1.325 2.650

14-1/4

B

2 places

Dia. .563

A

.19

2-1/2

1

1/2-13UNC-2B hex. hd. aluminum nut centered over 9/16” dia. clearance hole in aluminum pipe - two required

C

D

Dia. .563 Txx 3 placesDia. .400 ASTxx 2 places

1/2-13UNC-2A x 1-1/2 long hex. hd. 18-8 stainless steel bolt - two required

E



Catalog Number:KAD 250M SR3 277 SCWA RPD04LPINotes:

Type:

SLALAND14-51183

OUTDOOR KAD-M-S

Catalog

Number

Notes

Type

All dimensions are inches (centimeters)

unless otherwise specified.

*Weight as configured in example below.

KAD

Series Wattage Distribution Voltage Ballast Mounting12

KAD Metal halide

70M1,2 250M5

100M1 320M4

150M 350M3,4

175M3 400M5,6

200M4

Highgpressure psodium1

70S

100S

150S

250S

400S

Ceramic metal halide

70MHC1,2

100MHC1

150MHC

Standard reflectors

R2 IES type IIasymmetric7

R3 IES type III asymmetric7

R4 IES type IV forward throw7ww

R5S IES type V square

High performanceg preflectors8

SR2 IES type IIasymmetric7

SR3 IES type IIIasymmetric7

SR4SC IES type IV forward throw

120

2089

2409

277

347

4809

TB10

23050HZ11

(blank) Magneticballast

CWI Contantwattage isolated11

SCWA Super CWApulse-start ballast

NOTE: For shipments to U.S.

territories, SCWA must be

specified to comply with EISA.

Ships in fixture cartonp

SPD__ Square pole

RPD__ Round pole

WBD__ Wall bracket

WWD__ Wood or pole wall

Ships separatelyp p y13,14

DAD12P Degree arm (pole)

DAD12WB Degree arm (wall)

WBA Decorative wall bracket15

KMA Mast arm external fitter

KTMB Twin mounting bar

Arm lengthg

04 4" arm

06 6" arm

09 9" arm

12 12" arm

ORDERING INFORMATION For shortest lead times, configure product using bolded options. Example: KAD 400M R3 TB SCWA SPD04 LPI

Options Finish20 Lamp21

Shipped installed in fixturepp

SF Single fuse (120, 277, 347V)16

DF Double fuse (208, 240, 480V)16

PD Power tray17

PER NEMA twist-lock receptacle only(no photocontrol)

QRS Quartz restrike system18

QRSTD QRS time delay18

WTB Terminal wiring block17

HS House side shield

CSA CSA Certified

INTL Available MH for probe start shipping outside the U.S.

REGC1 California Title 20, effective 1/1/2010

Shipped separatelypp p y13

PE1 NEMA twist-lock PE (120, 208, 240V)

PE3 NEMA twist-lock PE (347V)



SC Shorting cap for PER option

VG Vandal guard19

WG Wire guard19

(blank) Dark bronze

DWH White

DBL Black

DMB Medium bronze

DNA Natural aluminum

LPI Lamp included

L/LP Less lamp

Soft Square Lighting

KADMETAL HALIDE: 70-400W

HIGH PRESSURE SODIUM: 70-400W

20’ TO 35’ MOUNTING

Specifications

EPA: 1.2 ft.2

*Weight: 35.9 lbs (16.28 kg)

Length: 17-1/2 (44.5)

Width: 17-1/2” (44.5)

Depth: 7-1/8 (18.1)

FEATURES & SPECIFICATIONSINTENDED USE – Ideal for parking areas, street lighting, walkways and car lots.

CONSTRUCTION – Rugged, die-cast, soft corner aluminum housing with 0.12” nominal wall thickness. Die-cast door

frame has impact-resistant,tempered, glass lens that is fully gasketed with one-piece tubular silicone.

Finish: Standard finish is dark bronze (DDB) polyester powder finish, with other architectural colors available.

OPTICS – Anodized, aluminum reflectors: IES full cutoff distributions R2 (asymmetric), R3 (asymmetric), R4

(forward throw) and R5S (square) are interchangeable. High-performance anodized, segmented aluminum

reflectors IES full cutoff distributions SR2 (asymmetric), SR3 (asymmetric) and SR4SC (forward throw, sharp

cutoff). High-performance reflectors attach with tool-less fasteners and are rotatable and interchangeable.

ELECTRICAL – Ballast: High pressure sodium: 70-150W is high reactance, high power factor. Constant wattage

autotransformer for 200-400W. Metal halide: 70-150W is high reactance, high power factor and is standard with

pulse-start ignitor technology. “SCWA” not required. Constant wattage autotransformer for 175-400W. Super CWA

(pulse start ballast), 88% efficient and EISA legislation compliant, is required for metal halide 151-400W (SCWA

option) for US shipments only. CSA, NOM or INTL required for probe start shipments outside of the US. Pulse-start

ballast (SCWA) required for 200W, 320W, or 350W. Ballast is 100% factory-tested.

Socket: Porcelain, horizontally oriented medium base socket for 70-150M. Mogul base socket for 175M and above,

and 70-400S, with copper alloy, nickel-plated screw shell and center contact. UL listed 1500W, 600V.

LISTINGS – UL Listed (standard). CSA Certified (see Options). UL listed for 25°C ambient and wet locations. IP65

rated in accordance with standard IEC 529.

Specifications subject to change without notice.

Notes

1 Not available with SCWA.

2 Not available with 480V.

3 These wattages do not comply with California Title 20 regulations.

4 Must be ordered with SCWA.

5 These wattages require the REGC1 option to be chosen for shipments into

California for Title 20 compliance. 250M REGC1 in not available in 347 or 480V.

6 Reduced jacket ED28 required for SR2, SR3 and SR4SC optics.

7 House-side shield available.

8 High performance reflectors not available with QRSTD.

9 Must specify CWI for use in Canada.

10 Optional multi-tap ballast (120, 208, 240, 277V; in Canada: 120, 277, 347V).

11 Consult factory for available wattages.

12 9" arm is required when two or more luminaires are oriented

on a 90° drilling pattern.

13 May be ordered as an accessory.

14 Must specify finish when ordered as an accessory.

15 Available with SPD04 and SPD09.

16 Must specicy voltage. N/A with TB.

17 Only available with SR2, SR3 and SR4SC optics.

18 Max allowable wattage lamp included.

19 Prefix with KAD when ordered as an accessory.

20 See www.lithonia.com/archcolors for additional color options.

21 Must be specified. L/LP not available with MHC.

22 Must use RPD09.

7-1/8(18.1)

4(10.2)

17-1/2(44.5)

Accessories: Tenon Mounting Slipfitter (RPxx required.)Order as seperate catalog number. Must be used with pole mounting.

Number of fixtures

Tenon O.D. One Two@180° Two@90° Three@120° Three@90° Four@90°

2-3/8" T20-190 T20-280 T20-29022 T20-32022 T20-39022 T20-49022

2-7/8" T25-190 T25-280 T25-29022 T25-320 T25-39022 T25-49022

4 T35-190 T35-280 T35-29022 T35-320 T35-39022 T35-49022

250M SR3 277 SCWA RPD04

LPI




Type:

SLALAND14-51183

KAD-M-S

OUTDOOR: One Lithonia Way Conyers, GA 30012 Phone: 770.922.9000 Fax: 770-918-1209 www.lithonia.com ©2007-2010 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/16/10

KAD Metal Halide, Arm-mounted Soft Square Cutoff

Mounting Height Correction Factor

(Multiply the fc level by the correction factor)

25 ft. = 0.64

35 ft. = 0.32

40 ft. = 0.25

Coefficient of UtilizationInitial Footcandles

Notes

1 Photometric data for other distributions can be accessed at www.lithonia.com.

2 Tested to current IES and NEMA standards under stabilized laboratory conditions. Various operating factors can cause

differences between laboratory data and actual field measurements. Dimensions and specifications on this sheet are

based on the most current available data and are subject to change without notice.

3 For electrical characteristics, consult outdoor technical data specification sheets on www.lithonia.com.

Existing Mounting Height New Mounting Height

2

= Correction Factor

KAD 400M R2 Test no. 1193083101P KAD 400M R3 Test no. 1192040902P

KAD 400M R4HS Test no. 1192061101PKAD 400M R4 Test no. 1191110101P

DIS

TAN

CE

IN U

NIT

S O

F M

OU

NTI

NG

HE

IGH

T

ISOILLUMINANCE PLOT (Footcandle)

400W pulse start metal halide lamp, rated 38000 lumens. Footcandle values based on 20'mounting height.Classification: Type II, Short, Full Cutoff

-3

-2

-1

0

1

2

3

40 1 2 3 4 5 6

52.51.510.5

0.25

DIS

TAN

CE

IN U

NIT

S O

F M

OU

NTI

NG

HE

IGH

T


400W pulse start metal halide lamp, rated 38,000 lumens. Footcandle values based on 20'mounting height.Classification: Type II, Short, Full Cutoff

-3

-2

-1

0

1

2

3

40 1 2 3 4 5 6

52.51.5

10.5

0.25

DIS

TAN

CE

IN U

NIT

S O

F M

OU

NTI

NG

HE

IGH

T


400W pulse start metal halide lamp, rated 38,000 lumens. Footcandle values based on 20'mounting height.Classification: Unclassified (Type III, Very Short), Full Cutoff

-3

-2

-1

0

1

2

3

40 1 2 3 4 5 6

52.51.510.5

0.25

DIS

TAN

CE

IN U

NIT

S O

F M

OU

NTI

NG

HE

IGH

TISOILLUMINANCE PLOT (Footcandle)

400W pulse start metal halide lamp, rated 38,000 lumens. Footcandle values based on 20'mounting height.Classification: Unclassified (Type III, Very Short), Full

-3

-2

-1

0

1

2

3

40 1 2 3 4 5 6

52.51.510.5

0.25

KAD 400M R5S Test no. 1194040801P

DIS

TAN

CE

IN U

NIT

S O

F M

OU

NTI

NG

HE

IGH

T


400W pulse start metal halide lamp, rated 38000 lumens. Footcandle values based on 20'mounting height.Classification: Unclassified (Type NC, Very Short), Full Cutoff

-3

-2

-1

0

1

2

3

40 1 2 3 4 5 6

52.51.510.5

0.25



Catalog Number:40'OAL/30'MH/10'BURIAL TYPE II/O WITH SECONDRACEWAY IN POLE FOR LIGHTNING PROTECTIONDOWN CONDUSTORNotes:

Type:

SLBLAND14-51183




Notes:

Type:

SLBLAND14-51183

Catalog Number

Notes Type







DRILL PATTERN

Outdoor






190 1 at 90° 280 2 at 180° 290 2 at 90° 320 3 at 120° 390 3 at 90° 490 4 at 90°



Finish3


(powder finish)

–T20 280




Notes:

Type:

SLBLAND14-51183










14-1/4

B

2 places

Dia. .563

A

.19

2-1/2

1


C

D



E




Type:

SLBLAND14-51183

OUTDOOR KAD-M-S

Catalog

Number

Notes

Type


unless otherwise specified.


KAD

Series Wattage Distribution Voltage Ballast Mounting12

KAD Metal halide

70M1,2 250M5

100M1 320M4

150M 350M3,4

175M3 400M5,6

200M4

Highgpressure psodium1

70S

100S

150S

250S

400S


70MHC1,2

100MHC1

150MHC

Standard reflectors

R2 IES type IIasymmetric7

R3 IES type III asymmetric7

R4 IES type IV forward throw7ww

R5S IES type V square

High performanceg preflectors8

SR2 IES type IIasymmetric7

SR3 IES type IIIasymmetric7

SR4SC IES type IV forward throw

120

2089

2409

277

347

4809

TB10

23050HZ11

(blank) Magneticballast

CWI Contantwattage isolated11

SCWA Super CWApulse-start ballast

NOTE: For shipments to U.S.



Ships in fixture cartonp

SPD__ Square pole

RPD__ Round pole

WBD__ Wall bracket

WWD__ Wood or pole wall

Ships separatelyp p y13,14

DAD12P Degree arm (pole)

DAD12WB Degree arm (wall)

WBA Decorative wall bracket15

KMA Mast arm external fitter

KTMB Twin mounting bar

Arm lengthg

04 4" arm

06 6" arm

09 9" arm

12 12" arm

ORDERING INFORMATION For shortest lead times, configure product using bolded options. Example: KAD 400M R3 TB SCWA SPD04 LPI

Options Finish20 Lamp21

Shipped installed in fixturepp

SF Single fuse (120, 277, 347V)16

DF Double fuse (208, 240, 480V)16

PD Power tray17

PER NEMA twist-lock receptacle only(no photocontrol)

QRS Quartz restrike system18

QRSTD QRS time delay18

WTB Terminal wiring block17

HS House side shield

CSA CSA Certified

INTL Available MH for probe start shipping outside the U.S.

REGC1 California Title 20, effective 1/1/2010

Shipped separatelypp p y13

PE1 NEMA twist-lock PE (120, 208, 240V)




SC Shorting cap for PER option

VG Vandal guard19

WG Wire guard19

(blank) Dark bronze

DWH White

DBL Black

DMB Medium bronze


LPI Lamp included

L/LP Less lamp

Soft Square Lighting

KADMETAL HALIDE: 70-400W

HIGH PRESSURE SODIUM: 70-400W

20’ TO 35’ MOUNTING

Specifications

EPA: 1.2 ft.2

*Weight: 35.9 lbs (16.28 kg)

Length: 17-1/2 (44.5)

Width: 17-1/2” (44.5)

Depth: 7-1/8 (18.1)

FEATURES & SPECIFICATIONSINTENDED USE – Ideal for parking areas, street lighting, walkways and car lots.

CONSTRUCTION – Rugged, die-cast, soft corner aluminum housing with 0.12” nominal wall thickness. Die-cast door

frame has impact-resistant,tempered, glass lens that is fully gasketed with one-piece tubular silicone.

Finish: Standard finish is dark bronze (DDB) polyester powder finish, with other architectural colors available.

OPTICS – Anodized, aluminum reflectors: IES full cutoff distributions R2 (asymmetric), R3 (asymmetric), R4

(forward throw) and R5S (square) are interchangeable. High-performance anodized, segmented aluminum

reflectors IES full cutoff distributions SR2 (asymmetric), SR3 (asymmetric) and SR4SC (forward throw, sharp

cutoff). High-performance reflectors attach with tool-less fasteners and are rotatable and interchangeable.

ELECTRICAL – Ballast: High pressure sodium: 70-150W is high reactance, high power factor. Constant wattage

autotransformer for 200-400W. Metal halide: 70-150W is high reactance, high power factor and is standard with

pulse-start ignitor technology. “SCWA” not required. Constant wattage autotransformer for 175-400W. Super CWA

(pulse start ballast), 88% efficient and EISA legislation compliant, is required for metal halide 151-400W (SCWA

option) for US shipments only. CSA, NOM or INTL required for probe start shipments outside of the US. Pulse-start

ballast (SCWA) required for 200W, 320W, or 350W. Ballast is 100% factory-tested.

Socket: Porcelain, horizontally oriented medium base socket for 70-150M. Mogul base socket for 175M and above,

and 70-400S, with copper alloy, nickel-plated screw shell and center contact. UL listed 1500W, 600V.

LISTINGS – UL Listed (standard). CSA Certified (see Options). UL listed for 25°C ambient and wet locations. IP65

rated in accordance with standard IEC 529.

Specifications subject to change without notice.

Notes





5 These wattages require the REGC1 option to be chosen for shipments into

California for Title 20 compliance. 250M REGC1 in not available in 347 or 480V.

6 Reduced jacket ED28 required for SR2, SR3 and SR4SC optics.

7 House-side shield available.

8 High performance reflectors not available with QRSTD.


10 Optional multi-tap ballast (120, 208, 240, 277V; in Canada: 120, 277, 347V).


12 9" arm is required when two or more luminaires are oriented

on a 90° drilling pattern.


14 Must specify finish when ordered as an accessory.

15 Available with SPD04 and SPD09.

16 Must specicy voltage. N/A with TB.

17 Only available with SR2, SR3 and SR4SC optics.

18 Max allowable wattage lamp included.

19 Prefix with KAD when ordered as an accessory.


21 Must be specified. L/LP not available with MHC.

22 Must use RPD09.

7-1/8(18.1)

4(10.2)

17-1/2(44.5)

Accessories: Tenon Mounting Slipfitter (RPxx required.)Order as seperate catalog number. Must be used with pole mounting.

Number of fixtures

Tenon O.D. One Two@180° Two@90° Three@120° Three@90° Four@90°

2-3/8" T20-190 T20-280 T20-29022 T20-32022 T20-39022 T20-49022

2-7/8" T25-190 T25-280 T25-29022 T25-320 T25-39022 T25-49022

4 T35-190 T35-280 T35-29022 T35-320 T35-39022 T35-49022

250M SR3 277 SCWA RPD04

LPI




Type:

SLBLAND14-51183

KAD-M-S


KAD Metal Halide, Arm-mounted Soft Square Cutoff



25 ft. = 0.64

35 ft. = 0.32

40 ft. = 0.25

Coefficient of UtilizationInitial Footcandles

Notes

1 Photometric data for other distributions can be accessed at www.lithonia.com.

2 Tested to current IES and NEMA standards under stabilized laboratory conditions. Various operating factors can cause

differences between laboratory data and actual field measurements. Dimensions and specifications on this sheet are

based on the most current available data and are subject to change without notice.

3 For electrical characteristics, consult outdoor technical data specification sheets on www.lithonia.com.


2

= Correction Factor

KAD 400M R2 Test no. 1193083101P KAD 400M R3 Test no. 1192040902P

KAD 400M R4HS Test no. 1192061101PKAD 400M R4 Test no. 1191110101P

DIS

TAN

CE

IN U

NIT

S O

F M

OU

NTI

NG

HE

IGH

T


400W pulse start metal halide lamp, rated 38000 lumens. Footcandle values based on 20'mounting height.Classification: Type II, Short, Full Cutoff

-3

-2

-1

0

1

2

3

40 1 2 3 4 5 6

52.51.510.5

0.25

DIS

TAN

CE

IN U

NIT

S O

F M

OU

NTI

NG

HE

IGH

T


400W pulse start metal halide lamp, rated 38,000 lumens. Footcandle values based on 20'mounting height.Classification: Type II, Short, Full Cutoff

-3

-2

-1

0

1

2

3

40 1 2 3 4 5 6

52.51.5

10.5

0.25

DIS

TAN

CE

IN U

NIT

S O

F M

OU

NTI

NG

HE

IGH

T


400W pulse start metal halide lamp, rated 38,000 lumens. Footcandle values based on 20'mounting height.Classification: Unclassified (Type III, Very Short), Full Cutoff

-3

-2

-1

0

1

2

3

40 1 2 3 4 5 6

52.51.510.5

0.25

DIS

TAN

CE

IN U

NIT

S O

F M

OU

NTI

NG

HE

IGH

TISOILLUMINANCE PLOT (Footcandle)

400W pulse start metal halide lamp, rated 38,000 lumens. Footcandle values based on 20'mounting height.Classification: Unclassified (Type III, Very Short), Full

-3

-2

-1

0

1

2

3

40 1 2 3 4 5 6

52.51.510.5

0.25

KAD 400M R5S Test no. 1194040801P

DIS

TAN

CE

IN U

NIT

S O

F M

OU

NTI

NG

HE

IGH

T


400W pulse start metal halide lamp, rated 38000 lumens. Footcandle values based on 20'mounting height.Classification: Unclassified (Type NC, Very Short), Full Cutoff

-3

-2

-1

0

1

2

3

40 1 2 3 4 5 6

52.51.510.5

0.25



Catalog Number:25'OAL/18'MH/7'BURIAL TYPE I/O WITH SECONDRACEWAY IN POLE FOR LIGHTNING PROTECTIONDOWN CONDUSTORNotes:

Type:

SLCLAND14-51183



Catalog Number:KAD LED 1 63B530/50K SR3 MVOLTRPD09 DDBXDNotes: Verify finish. Schedule states CBA

Type:

SLCLAND14-51183

Specifications

EPA: 1.2 ft2

(0.11 m2)

Length: 17-1/2”(44.5 cm)

Width: 17-1/2”(44.5 cm)

Height: 7-1/8”(18.1 cm)

Weight (max):

36 lbs(16.4 kg)

NOTES

1 Configured with 4000K (/40K) provides the shortest lead times. Consult factory for 3000K (/30K) and 5000K (/50K) lead times.

2 MVOLT driver operates on any line voltage from 120-277V (50/60 Hz). Specify 120, 208, 240 or 277 options only when ordering with fusing (SF, DF options).

3 Single fuse (SF) requires 120, 277 or 347 voltage option. Double fuse (DF) requires 208, 240 or 480 voltage option.

4 Not available with 347 or 480V.5 Also available as a separate accessory; see

Accessories information at left.6 Requires luminaire to be specified with PER

option. Ordered and shipped as a separate line item.

DSS124N 1.5 TJJE U Photocell - SSL twist-lock (120-277V) 6

REN480 NM1 J1 ROAM® node (480V) 6

SC U Shorting cap 6

KMA DDBXD U Mast arm adapter (specify finish)

KADWG U Wire guard accessory

KADVG U Vandal guard accessory

AccessoriesOrdered and shipped separately.

KAD LEDLED Area Luminaire

Ordering Information EXAMPLE: KAD LED 1 63B350/40K SR5 MVOLT SPD04 DDBXD

Catalog Number

Notes

Type

www.lithonia.com

Hit the Tab key or mouse over the page to see all interactive elements.

Introduction®

The KAD LED combines the latest in LED

®

For more control options, visit DTL and ROAM online.

Drilling

Tenon O.D. Single Unit 2 at 180° 2 at 90° † 3 at 120° 3 at 90° † 4 at 90° †

2-3/8” T20-190 T20-280 T20-290 T20-320 † T20-390 T20-4902-7/8” T25-190 T25-280 T25-290 T25-320 T25-390 T25-490

4” T35-190 T35-280 T35-290 T35-320 T35-390 T35-490

Tenon Mounting Slipfitter *

* For round pole mounting (RPA) only. † Requires 9” or 12” arm.

L

H

KAD LED

Series Light Engines Performance Package 1 Distribution Voltage Mounting Options Finish (required)

KAD LED 1 One engine (49 or 63 LEDs)

350 mA options:49B350/30K 3000K

49B350/40K 4000K

49B350/50K 5000K

63B350/30K 3000K

63B350/40K 4000K

63B350/50K 5000K

530 mA options:63B530/30K 3000K

63B530/40K 4000K

63B530/50K 5000K

SR2 Type II

SR3 Type III

SR4 Type IV

SR5 Type V

MVOLT 2

120 2

208 2

240 2

277 2

347

480

Shipped includedType LengthSPD__ Square pole 04 4" arm

RPD__ Round pole 06 6" arm

WBD__ Wall bracket 09 9" arm

WWD__ Wood pole or wall

12 12" arm

Shipped installedPER NEMA twist-lock receptacle only (no

controls)

SF Single fuse (120, 277, 347V) 3

DF Double fuse (208, 240, 480V) 3

DMG 0-10V dimming driver (no controls) 4

DFL Diffusing lens

Shipped separately VG Vandal guard 5

WG Wire guard 5

DDBXD Dark bronze

DBLXD Black

DNAXD Natural aluminum

DWHXD White

DDBTXD Textured dark bronze

DBLBXD Textured black

DNATXD Textured natural aluminum

DWHGXD Textured white

Template #5Top of Pole

9/16"Diam(3 pla

2-1/8"

2-1/8"

Dia.

1 63B530/50K MVOLT RPD09 DDBXDSR3



Catalog Number:KAD LED 1 63B530/50K SR3 MVOLTRPD09 DDBXDNotes: Verify finish. Schedule states CBA

Type:

SLCLAND14-51183

Lumen values are from photometric tests performed in accordance with IESNA LM-79-08. Data is considered to be representative of the configurations shown, within the tolerances allowed by Lighting Facts. Actual performance may differ as a result of end-user environment and application. Contact factory for performance data on any configurations not shown here.

To see complete photometric reports or download .ies files for this product, visit Lithonia Lighting’s KAD LED homepage.

Current (A)

Light Engines

Drive Current (mA)

System Watts

120 208 240 277 347 480

1 (49) 350 59W 0.55 0.32 0.27 0.24 0.19 0.14

1 (63)350 74W 0.69 0.40 0.34 0.30 0.24 0.17

530 109W 1.01 0.58 0.50 0.44 0.35 0.25

Electrical Load

FEATURES & SPECIFICATIONS

INTENDED USE

.

CONSTRUCTION

FINISH

OPTICS

ELECTRICAL

INSTALLATION

LISTINGS °

minimum ambient.

WARRANTY

.

Note:

Performance Data

Photometric Diagrams

www.lithonia.com

Lumen OutputUse these factors to determine relative lumen output for average ambient temperatures from 0-40°C (32-104°F).

Lumen Ambient Temperature (LAT) Multipliers

Ambient Lumen Multiplier

0°C 32°F 1.02

10°C 50°F 1.01

20°C 68°F 1.00

25°C 77°F 1.00

30°C 86°F 1.00

40°C 104°F 0.99

Projected LED Lumen MaintenanceData references the extrapolated performance projections for the KAD LED 1 63B530 platform in a 40°C ambient, based on 10,000 hours of LED testing (tested per IESNA LM-80-08 and projected per IESNA TM-21-11).

To calculate LLF, use the lumen maintenance factor that corresponds to the desired number of operating hours below. For other lumen maintenance values, contact factory.

Operating Hours 0 25,000 50,000 100,000

Lumen Maintenance Factor

1.0 0.95 0.92 0.87

4

3

2

1

0

-4

-3

-2

-1

4 3 2 1 0 4321

4

3

2

1

0

-4

-3

-2

-1

4 3 2 1 0 4321

4

3

2

1

0

-4

-3

-2

-1

4 3 2 1 0 4321

4

3

2

1

0

-4

-3

-2

-1

4 3 2 1 0 4321LEGEND

0.1 fc

0.5 fc

1.0 fc

Light

Engines

Drive

Current

(mA)

Performance

Package

System

Watts

Dist.

Type

40K

(4000K, 67 CRI)

Lumens B U G LPW

1

(49 LEDs)

350 49B350/--K 59 W

SR2 5068 1 0 1 86

SR3 4663 1 0 1 80

SR4 4667 1 0 1 80

SR5 4853 3 0 1 82

1

(63 LEDs)

350 63B350/--K 74 W

SR2 6148 1 0 1 83

SR3 6374 1 0 1 86

SR4 6250 1 0 1 84

SR5 6464 3 0 1 87

530 63B530/--K 109W

SR2 8353 2 0 2 77

SR3 8595 2 0 2 79

SR4 8246 2 0 2 76

SR5 8452 3 0 1 78




Notes:

Type:

SLCLAND14-51183

Catalog Number

Notes Type







DRILL PATTERN

Outdoor






190 1 at 90° 280 2 at 180° 290 2 at 90° 320 3 at 120° 390 3 at 90° 490 4 at 90°



Finish3


(powder finish)

–T20 190




Notes:

Type:

SLCLAND14-51183










14-1/4

B

2 places

Dia. .563

A

.19

2-1/2

1


C

D



E



Catalog Number:DSXW1 LED 10C 1000 50K T2MMVOLTNotes: Verify finish. Schedule states CBA

Type:

WMDLAND14-51183

DSXW1 LED

Series Performance Package Distribution Voltage Mounting Control Options Other Options Finish (required)

DSXW1 LED LEDs10C 10 LEDs

(one engine)

20C 20 LEDs

(two engines)

Drive current350 350 mA

530 530 mA

700 700 mA

1000 1000 mA (1 A)

Color temperature30K 3000K

40K 4000K

50K 5000K

T2S Type II Short

T2M Type II Medium

T3S Type III Short

T3M Type III Medium

T4M Type IV Medium

TFTM Forward Throw

Medium

MVOLT 1

120 1

208 1

240 1

277 1

Shipped included(blank) Surface

mounting bracket

BBW Surface-mounted back box (for conduit entry)2

Shipped installedPE Photoelectric cell,

button type 3

DMG 0-10V dimming driver (no controls)

PIR 180° motion sensor, <15’ mtg ht 4, 6

PIRH 180° motion sensor, 15-30’ mtg ht 4, 6

ELCW Emergency battery backup (includes external component enclosure) 7

Shipped installedSF Single fuse

(120, 277V) 8

DF Double fuse

(208, 240V) 8

HS House-side shield 9

Shipped separatelyBSW Bird-deterrent

spikes 9

WG Wire guard 9

VG Vandal guard 9

DDBXD Dark bronze

DBLXD Black

DNAXD Natural aluminum

DWHXD White

DSSXD Sandstone

DDBTXD Textured dark bronze

DBLBXD Textured black

DNATXD Textured natural aluminum

DWHGXD Textured white

DSSTXD Textured sandstone

D-Series Size 1LED Wall Luminaire

Ordering Information EXAMPLE: DSXW1 LED 20C 1000 40K T3M MVOLT DDBTXD

NOTES

1 MVOLT driver operates on any line voltage from 120-277V (50/60 Hz). Specify 120, 208, 240 or 277 options only when ordering with fusing (SF, DF options), or photocontrol (PE option).

2 Back box ships installed on fixture. Cannot be field installed. Cannot be ordered as an accessory.3 Photocontrol (PE) requires 120, 208, 240 or 277 voltage option. 4 Specifies the Sensor Switch SBR-10-ODP control; see Motion Sensor Guide for details. Dimming driver

standard.5 Specifies the Sensor Switch SBR-6-ODP control; see Motion Sensor Guide for details. Dimming driver

standard.6 Not available with 20 LED/1000 mA configuration (DSXW1 LED 20C 1000).7 Not compatible with conduit entry applications. Not available with BBW mounting option. 8 Single fuse (SF) requires 120 or 277 voltage option. Double fuse (DF) requires 208 or 240 voltage option. 9 Also available as a separate accessory; see Accessories information.

Catalog Number

Notes

Type

AccessoriesOrdered and shipped separately.

DSXWHS U House-side shield (one per light engine)

DSXWBSW U Bird-deterrent spikes

DSXW1WG U Wire guard accessory

DSXW1VG U Vandal guard accessory

Hit the Tab key or mouse over the page to see all interactive elements.

Introduction

Luminaire

Width:(34.9 cm)

Depth:(25.4 cm)

Height:(16.2 cm)

Back Box (BBW, ELCW)

Width:(34.9 cm)

Depth:(10.2 cm)

Height:(16.2 cm)

Specifications

Weight: (5.4 kg)

BBW Weight: (2.3 kg)

ELCW Weight: (4.5 kg)

D

H

W

4

6-3/8

D

H

13-3/4

6-3/

W

10C 1000 50K DDBXDT2M MVOLT - - -



Catalog Number:DSXW1 LED 10C 1000 50K T2MMVOLTNotes: Verify finish. Schedule states CBA

Type:

WMDLAND14-51183

LEDs

Drive

Current

(mA)

Performance

Package

System

Watts

Dist.

Type

40K

(4000K, 70 CRI)

50K

(5000K, 65 CRI)

Lumens B U G LPW Lumens B U G LPW

10C

(10 LEDs)

530 10C 530 --K 20 W

T2S 1724 1 0 1 86 1807 1 0 1 90

T2M 1729 1 0 1 86 1812 1 0 1 91

T3S 1709 1 0 1 85 1792 1 0 1 90

T3M 1753 1 0 1 88 1838 1 0 1 92

T4M 1753 1 0 1 88 1837 1 0 1 92

TFTM 1766 1 0 1 88 1851 1 0 1 93

700 10C 700 --K 27 W

T2S 2234 1 0 1 83 2341 1 0 1 87

T2M 2241 1 0 1 83 2349 1 0 1 87

T3S 2216 1 0 1 82 2322 1 0 1 86

T3M 2272 1 0 1 84 2381 1 0 1 88

T4M 2272 1 0 1 84 2381 1 0 1 88

TFTM 2289 1 0 1 85 2399 1 0 1 89

1000 10C 1000 --K 40 W

T2S 2992 1 0 1 75 3136 1 0 1 78

T2M 3001 1 0 1 75 3146 1 0 1 79

T3S 2967 1 0 1 74 3110 1 0 1 78

T3M 3043 1 0 1 76 3189 1 0 1 80

T4M 3043 1 0 1 76 3189 1 0 1 80

TFTM 3066 1 0 1 77 3213 1 0 1 80

20C

(20 LEDs)

530 20C 530 --K 36 W

T2S 3545 1 0 1 98 3715 1 0 1 103

T2M 3556 1 0 1 99 3727 1 0 1 104

T3S 3515 1 0 1 98 3685 1 0 1 102

T3M 3606 1 0 2 100 3779 1 0 2 105

T4M 3605 1 0 1 100 3779 1 0 1 105

TFTM 3632 1 0 1 101 3807 1 0 1 106

700 20C 700 --K 47 W

T2S 4357 1 0 1 93 4566 1 0 1 97

T2M 4370 1 0 1 93 4580 1 0 1 97

T3S 4320 1 0 1 92 4528 1 0 1 96

T3M 4431 1 0 2 94 4644 1 0 2 99

T4M 4430 1 0 1 94 4644 1 0 2 99

TFTM 4464 1 0 1 95 4678 1 0 1 100

1000 20C 1000 --K 75 W

T2S 5745 2 0 2 77 6020 2 0 2 80

T2M 5763 1 0 2 77 6039 2 0 2 81

T3S 5697 1 0 1 76 5970 1 0 2 80

T3M 5843 1 0 2 78 6123 2 0 2 82

T4M 5843 1 0 2 78 6123 1 0 2 82

TFTM 5887 1 0 2 78 6169 1 0 2 82

Lumen values are from photometric tests performed in accordance with IESNA LM-79-08. Data is considered to be representative of the configurations shown, within the tolerances allowed by Lighting Facts. Actual performance may differ as a result of end-user environment and application. Contact factory for performance data on any configurations not shown here.

Performance Data

Lumen Output

Electrical Load

Use these factors to determine relative lumen output for average ambient temperatures from 0-40°C (32-104°F).

Lumen Ambient Temperature (LAT) Multipliers

Ambient Lumen Multiplier

0°C 32°F 1.02

10°C 50°F 1.01

20°C 68°F 1.00

25°C 77°F 1.00

30°C 86°F 1.00

40°C 104°F 0.98

Projected LED Lumen MaintenanceData references the extrapolated performance projections for the DSXW1 LED 20C 1000 platform in a 25°C ambient, based on 10,000 hours of LED testing (tested per IESNA LM-80-08 and projected per IESNA TM-21-11).

To calculate LLF, use the lumen maintenance factor that corresponds to the desired number of operating hours below. For other lumen maintenance values, contact factory.

Operating Hours 0 25,000 50,000 100,000

Lumen Maintenance Factor

1.0 0.95 0.93 0.88

FEATURES & SPECIFICATIONS

INTENDED USE

CONSTRUCTION

FINISH

OPTICS

ELECTRICAL

°

INSTALLATION

LISTINGS °

WARRANTY

Note:

To see complete photometric reports or download .ies files for this product, visit Lithonia Lighting’s D-Series Wall Size 1 homepage. Photometric Diagrams

LEGEND

DSXW1,0.5 fc

TWF2,0.5 fc

10’ W Sidewalk

LLDs:

TWF2 = 0.72

DSXW1 = 0.95

4

3

2

1

0

-4

-3

-2

-1

4 3 2 1 0 4321

4

3

2

1

0

-4

-3

-2

-1

4 3 2 1 0 4321LEGEND

0.1 fc

0.5 fc

1.0 fc

TWF2:

DSXW1:

Current (A)

LEDsDrive Current

(mA)System Watts

120 208 240 277 347 480

10C

350 14 W 0.13 0.07 0.06 0.06 - -

530 20 W 0.19 0.11 0.09 0.08 - -

700 27 W 0.25 0.14 0.13 0.11 - -

1000 40 W 0.37 0.21 0.19 0.16 - -

20C

350 25 W 0.23 0.13 0.12 0.10 - -

530 36 W 0.33 0.19 0.17 0.14 - -

700 47 W 0.44 0.25 0.22 0.19 - -

1000 75 W 0.69 0.40 0.35 0.30 - -

4

3

2

1

0

-4

-3

-2

-1

4 3 2 1 0 4321

TWF2: DSXW1:



Catalog Number:TWH 100M 277 SF LPI

Notes:

Type:

WPIALAND14-51183

OUTDOOR TWH M S L

Catalog

Number

Notes

Type

15-3/4(40.0)

16-1/4(41.3)

8(20.3)

Wall Packs

TWH METAL HALIDE: 70W - 400W

HIGH PRESSURE SODIUM: 70W - 400W

LOW PRESSURE SODIUM: 35W

8' to 25' Mounting

ORDERING INFORMATION Example: TWH 100M TB LPI

TWH

Series Wattage Voltage Ballast Options Finish15 Lamp17

TWH Low pressure sodium1

35L

High pressure sodium1

70S

100S

150S2

200S

250S

400S

Metal halide

70M1, 3

100M1

150M

175M4

200M5

250M6

320M5

350M4, 5

400M6, 7


70MHC1, 3

100MHC1

150MHC

120

2088

2408

277

347

4808

TB9

2305HZ10

(blank) Magnetic ballast

CWI Constant wattage isolated

SCWA Super CWA pulse start ballast

Note: For shipments to U.S.



Shipped installed in fixture

SF Single fuse (120, 277, 347V)

DF Double fuse (208, 240, 480V)

EC Emergency circuit11

QRS Quartz restrike11

QRSTD Quartz restrike system with time delay10, 11

PE Photoelectric cell - button type3

PER NEMA twist-lock receptacle12

FS Full shield

TP Tamper proof screws

CSA Listed and labeled to comply with Canadian Standards

NOM NOM Certified10

INTL Available for MH probe start shipping outside the U.S.

REGC1 California Title 20 effective 1/1/2010

Shipped separately13

PE1 NEMA twist-lock PE (120V/208V/240V)




SC Shooting cap for PER option

VG Vandal guard14

WG Wire guard14

(blank) Dark bronze


DBL Black

DMB Medium bronze

DWH White

CR Enhanced corrosion resistant

CRT Non-stick protective coating16

LPI Lamp included

L/LP Less lamp

For shortest lead times, configure product using standard options (shown in bold).

FEATURES & SPECIFICATIONSINTENDED USE — Outdoor storage areas, warehouse and factory perimeters and loading docks.

CONSTRUCTION — Rugged, corrosion-resistant, die-cast aluminum. Corrosion-resistant external hardware

includes slotted hex-head fasteners.

Finish: Standard finish is electrostatically-applied, oven-cured, dark bronze (DDB) corrosion-resistant polyester

powder paint.

OPTICS — Reflector is specular anodized aluminum. Refractor is prismatic borosilicate glass which is sealed and gasketed

to inhibit the entrance of outside contaminants.

ELECTRICAL — Electrical components are mounted in hinged front cover that includes primary and secondary

electrical disconnect.

Ballast: Low pressure sodium: High reactance, high power factor. High pressure sodium: 70-150W is high reactance,

high power factor. Constant wattage autotransformer for 200-400W. Metal halide: 70-150W is high reactance, high

power factor and is standard with pulse-start ignitor technology. SCWA not required. Constant wattage autotrans-

former for 175-400W. Super CWA (pulse start ballast), 88% efficient and EISA legislation compliant, is required for

metal halide 151-400W (SCWA option) for US shipments only. CSA, NOM or INTL required for probe start shipments

outside of the US. Pulse-start ballast (SCWA) required for 200W, 320W, or 350W. Ballast is 100% factory-tested.

Socket: Porcelain, horizontally oriented, single-ended bayonet base socket for 35W low pressure sodium; medium

base socket for 70-150W; and mogul base socket for 175W and above, with copper alloy, nickel-plated screw shell

and center contact. UL listed 1500W, 600V.

INSTALLATION — Back housing is separated from front housing, eliminating ballast weight and promoting easy

handling. Top 3/4" threaded wiring access. Back access through removable 3/4" knockout. Feed-thru wiring can

be achieved by using a condulet tee. Mount on any vertical surface. Not recommended in applications where

a sprayed stream of water can come in direct contact with glass lens.

LISTINGS — UL Listed (standard). CSA or NOM Certified (see Options). UL listed for 25°C ambient and suitable

for wet locations. IP65 rated (250 watt and below) or IP54 rated (400 watt) in accordance with IEC Standard 529.

Note: Specifications subject to change without notice.

Notes


2 Operates 55V lamp.




6 These wattages require the REGC1 option to be chosen for shipments into California for Title 20 compliance. 250M REGC1 in not available in 347 or 480V.

7 Requires T-15, ED or BT28 reduced jacket lamp.


9 Optional multi-tap ballast (120, 208, 240, 277V); in Canada (120, 277, 347V).


11 Max allowable wattage lamp included .

12 Photocell not included.


14 Prefix with TWH when ordered as an accessory. Requires field modification.


16 Black finish only.

17 Must be specified. L/LP N/A MHC.

Specifications

Height: 15-3/4 (40.0)

Width: 16-1/4 (41.3)

Depth: 8 (20.3)

*Weight: 29.95 (13.59kg)


unless otherwise indicated.


100M 277 SF LPI



Catalog Number:TWH 100M 277 SF LPI

Notes:

Type:

WPIALAND14-51183

TWH M S L


TWH Metal Halide Wall-Packs

Coefficient of Utilization

Initial Footcandles

TWH 175M Test report no. 94121101P



15 ft. = .64 20 ft. = .36 25 ft. = .23

TWH 250M Test report no. 95011902P TWH 400M Test report no. 94112102P

Notes

1 Photometric data for other distributions can be accessed from the Lithonia Lighting Web site. (www.lithonia.com)


2

= Correction Factor

TWH 250S Test report no. 94121002

Dis

tanc

e in

uni

ts o

f mou

ntin

g he

ight

Coefficients of utilization

TWH 400S Test report no. 94121001

Dis

tanc

e in

uni

ts o

f mou

ntin

g he

ight

Coefficients of utilization

Distance in units of mounting height Distance in units of mounting height

250W, high pressure sodium lamp, horizontal lamp orienta-

tion, 12' mounting height, 27,500 rated lumens.

Total fixture efficiency: 70.9%

400W, high pressure sodium lamp, horizontal lamp orienta-

tion, 12' mounting height, 50,000 rated lumens.


2

1

0

1

2

3

4

5

10

1

2

2

.1

0 1 2 3 4 5 6

5

5

2

1

0

1

2

3

4

5

10

1

2

2

.1

0 1 2 3 4 5 6

5

5

TWH 35L Test report no. 94121902

2

1

0

1

2

3

4

5

1

2

2

.1

0 1 2 3 4 5 6

5

Distance in units of mounting height

Dis

tanc

e in

uni

ts o

f mou

ntin

g he

ight

35W, low pressure sodium lamp, horizontal lamp orientation, 12'

mounting height, 4,800 rated lumens.


DIS

TAN

CE

IN U

NIT

S O

F M

OU

NTI

NG

HE

IGH

T


175W pulse start metal halide lamp, horizontal lamp orientation Footcandle values based on 12'mounting height, 12800 rated lumens.

-2

-1

0

1

2

3

4

50 1 2 3 4 5 6

52.5

1.51

0.5

0.25

Luminaire Efficiency: 61%

DIS

TAN

CE

IN U

NIT

S O

F M

OU

NTI

NG

HE

IGH

T



-2

-1

0

1

2

3

4

50 1 2 3 4 5 6

52.5

1.51

0.5

0.25


DIS

TAN

CE

IN U

NIT

S O

F M

OU

NTI

NG

HE

IGH

T



-2

-1

0

1

2

3

4

50 1 2 3 4 5 6

52.5

1.51

0.5

0.25


TM

Square DTM brand SurgelogicTM SDSA3650 products are compact and affordable Surge Protective Devices (SPDs). SDSA3650 SPDs offer a simple means to bring down initial surges to manageable levels and can offer addtional value in a cascaded SPD system. Their compact design allows surge suppression to be installed adjacent to power panels or directly on sensitive equipment.

SDSA3650 SPDs Square D Type 1Surge Protective Devices

be025257

Text Box

Site Pole Lightning Arrestor Types SLA, SLB, SLC

2

Document Number 9990-0120B March 2011 bw

Schneider Electric USA, Inc. 1751 S. 4800 W., Salt Lake City, UT 84104, USA Telephone: (801)-977-9009 Fax: (801)-977-0200 www.surgelogic.com © 2

011

Sch

neid

er E

lect

ric. A

ll rig

hts

rese

rved

.

SDSA3650 SPDs Features

PerformanceSurge Current Rating per Phase 40kAShort Circuit Current Rating 200kAModes of Protection 6Fusing Individually fused MOVs Thermal Fusing YesOvercurrent Fusing YesOperating Frequency 50/60 Hz

Mechanical DescriptionEnclosure PlasticNEMA Rating NEMA Type 4XConnection Method #12 AWGWeight 1.8 lbsMounting Method Close Nippled, Back MountedOperating Altitude Sea Level-12,000’ (3,658 m)Storage Temperature -40˚ F to +149˚ F (-40˚ C to +65˚ C)Operating Temperature -40˚ F to +149˚ F (-40˚ C to +65˚ C)DiagnosticsGreen status LED Listings and PerformancecULus Listed per UL 1449 3rd edition Type 1 SPD, UL 1283, CSA C22.2 No. 8-M1986, C233.1-87CE marked (IEC 61643-11)

SDSA3650 SPDsSuperior Performance Square D brand Surgelogic SDSA3650 SPDs utilize high-energy suppression circuitry that can be located at any point in the electrical system. As a Type 1 rated device, they have the flexibility to be used with or without an Overcurrent Protection Device (OCPD).

SDSA3650 SPDs provide surge suppression for equipment from severe transient activity. Each metal oxide varistor (MOV) is individually fused and the products carry a NEMA Type 4X rating suitable for installing indoors, outdoors, or in other harsh environments.

Easy InstallationSurgelogic SDSA3650 SPDs are some of the most versatile, yet compact devices available on the market today. This compact package can be mounted on an electrical panel, meter socket, or inside electrical control cabinets.

WarrantyThe SDSA3650 and SDSA3650D warranty is 2 years.

0.5 [17.7]NPT straight

3.00[76]

3.60[92]

3.39[86]

2.64[67]

in.[mm]

VoltageSurge Current per Phase

Modes of Protection Configuration Model Number MCOV SCCR In

VPR

L-N L-G L-L N-G

600Y/347V1 40kA 6 3 Ø, 4-wire SDSA3650 750V L-N 1500V L-L 200kA 10kA 2500V N/A 4000V N/A

600V Delta2 40kA 3 3 Ø, 3-wire SDSA3650D 1500V L-L 200kA 10kA N/A N/A 4000V N/A

1 Applicable voltages: 120/240V, 208Y/120V, 380Y/220V, 400Y/230V, 480Y/277V, 600Y/347V2 Applicable voltages: 240V Delta, 480V Delta, 600V Delta

The SDSA3650 is a four-wire surge suppressor designed for use on all solidly grounded systems up to 600Y/347 Vac. The SDSA3650D is a three-wire surge suppressor designed for delta applications up to 600 Vac.

Square D and SurgeLogic are trademarks or registered trademarks of Schneider Electric and/or its affiliates in the United States and/or other countries. Other marks used herein may be the property of their respective owners.

be025257

Text Box

Site Pole Lightning Arrestor Types SLA, SLB, SLC

be025257

Rectangle

OCPS CLAY SPRINGS ES SUBMITTAL TRANSMITTAL · DRAWING AND/OR PRODUCT DATA SUBMITTAL. N ... DPRM Red...

Documents

Transcript of OCPS CLAY SPRINGS ES SUBMITTAL TRANSMITTAL · DRAWING AND/OR PRODUCT DATA SUBMITTAL. N ... DPRM Red...