Thermal and Mechanical Analysis of Nylon 6 and Nylon 66 Blends
Nylon 6/Tecamid Nylatron GSM - Righton Limited Plastics.pdf · Nylon 6/Tecamid Nylon 66 Nylatron GS...
Transcript of Nylon 6/Tecamid Nylatron GSM - Righton Limited Plastics.pdf · Nylon 6/Tecamid Nylon 66 Nylatron GS...
Expertise in Plastics
Nylon 6/Tecamid
Nylon 66
Nylatron GSNylon 66 Mos Filled
Nylatron GSMCast Nylon 6 Mos Filled
Acetal
6
/Tecamid 66
/Tecaform
PETP/Tecapet
PTFE
Ketron/TecapeekPEEK
Techtron HPV/TecatronPolyphenylene Sulphide (PPS)
Torlon/TecatorPolyamide Imide (PAI)
A partially crystalline polyamide with good strength, toughness and resilience. This is particularlyimportant under impact loading or at low temperatures. Available in round bar from 5mm - 320mm.
This material has a higher melting point than Nylon 6 and, in addition, better mechanicalproperties, greater hardness and low water absorption. This makes it ideal for components whichneed to meet close tolerances. Available in round bar from 5mm - 250mm and ¼” - 2".
The presence of the Mos filler results in greater wear resistance and lower coefficient of friction.Stiffness, tensile strength and temperature resistance are also improved.Available in round bar from 6mm - 250mm and ¼” - 2".
As Nylon GS but with enhanced wear resistance, self lubrication, greater temperature resistanceand low moisture absorption. Available in round bar from 50mm - 500mm.
A semi-crystalline copolymer with a good all-round balance of engineering properties. Operatescontinuously at 100°C and has the added advantage of low moisture absorption, good impactresistance and dimensional stability. Available in round bar from 4mm - 250mm and ¼” - 2".
2
2
A unique combination of properties. Better wear and abrasion resistance than nylon or acetal,wet or dry. Significantly better dimensional stability and low thermal expansion rate plus goodelectrical properties. Food grade rated. Available in round bar from 10mm - 200mm.
The most widely used fluoropolymer. Outstanding chemical resistance, low flammability andhigh degree of resistance to weathering. Available in round bar from 4mm - 90mm.
An outstanding advanced material for demanding applications where excellent mechanicalperformance under extreme conditions is a pre-requisite. Available in round bar from 4 - 200mm.
A reinforced, self lubricating polyphenylene sulphide for demanding applications. A cost effectivealternative to PEEK in some applications. Available in round bar from 4mm - 100mm.
A high performance material with exceptional mechanicalproperties, even when operating attemperatures of 260°C. Available in round bar from ¼” - 2½”.
®
®
®
®
®
®
®
57
Engineering PlasticsEngineering Plastics
Tough, resilient, good wear resistance. Good
chemical resistance and flexural fatigue
resistance.
Low weight ( / vs steel). Continuous
working temp: 70°C (max 140°C).
Tough, resilient, excellent wear resistance.
Good chemical resistance and flexural
fatigue resistance. Low weight ( / vs steel).
Higher tensile strength, stiffness and
hardness than Nylon 6. Continuous working
temp: 80°C (max 160°C).
High stiffness/strength and excellent wear
resistance. Good chemical resistance, self
lubricating, greater load bearing capability
than Nylon 66. Excellent dynamic bearing
material. Continuous working temp: 90°C
(max 160°C).
High stiffness/strength and good wear
resistance. Good chemical resistance, self
lubricating, an excellent dynamic bearing
material. Low weight ( / vs steel).
Continuous working temp: 90°C (max 170°C).
High rigidity, good impact strength and low
water absorption. Good chemical resistance
and excellent dimensional stability. Ideal for
close tolerance parts. Continuous working
temp: 100°C (max 140°C).
High mechanical strength, stiffness and
hardness. Very good creep resistance and
dimensional stability. Low moisture
absorption, excellent wear resistance, low
coefficient of friction and physiologically
inert. Continuous working temp: 100°C
(max 160°C).
1 6
1 6
1 6
Gears, bearings, rollers, wheels,
cams, nuts, valve seats, pulleys,
gaskets & electrical insulators.
Gears, bearings, rollers, wheels,
cams, nuts, valve seats, pulleys,
gaskets & electrical insulators.
Gears, bearings, rollers, wheels,
cams, nuts, valve seats, pulleys,
gaskets & electrical insulators.
Rail wheels, gears, bearings,
rollers, wheels, cams, nuts, valve
seats, pulleys, gaskets & electrical
insulators.
Pump housings, impellers, gears,
bearings, valves, valve seats,
domestic appliances & electrical
components.
Bearings, thrust washers,
slideways, gears, rollers, pump
components, insulating
components for electrical
engineering & food processing
equipment.
Characteristics Applications
Characteristics & Applications
Nylon 6
Tecamid®
6
Nylon 66
Tecamid®
66
Nylatron
GS
Nylatron
GSM
Acetal
Tecaform®
Ertalyte®
Tecapet®
PETP
Engineering PlasticsEngineering Plastics
58
Gaskets, chute linings, insulators,
valve seats & “O” rings.
Engine timing chain guides, coil
formers, bearings, pump & valve
seats/seals, insulators, bushings,
impellers & rotors.
Bearings, ball valves, pump &
valve compressor components &
seals.
Bearings, thrust washers, wear
pads, strips, piston rings, seals,
valves and valve seats.
Characteristics & Applications
Tough and flexible with a very low coefficient of
friction. Poor creep resistance. Non-stick
surface, excellent chemical resistance and
superb electrical/dielectric performance. Wide
operating range -260°C to +250°C.
Excellent chemical resistance and good
abrasion resistance. High stiffness/strength &
superb electrical/dielectric performance.
Hydrolysis and radiation resistance. Wide
operating range -60°C to +250°C.
Excellent chemical and abrasion resistance.
High stiffness/strength & low coefficient of
friction. Hydrolysis and radiation resistance.
Continuous working temp: 220°C (max 250°C).
Excellent chemical resistance and good wear
resistance. High stiffness/strength & low
coefficient of friction. Good radiation resistance
and dimensional stability. Wide operating range
-190°C to +260°C.
Characteristics Applications
The range shown above, is a list of the most commonly purchased products. If you require any otherengineering plastic material, please contact your local Righton Service Centre.
PTFE
Ketron
Tecapeek®
PEEK
Techtron
HPV
Tecalron®
Torlon
Tecator®
Engineering PlasticsEngineering Plastics
59