Nu Horizons Electroncis Portal - Europe

March 2009

In This Issue: Bus Interface

5V RS-485/RS-422 Half-Duplex Transceiver

High-Performance Low Voltage UARTs with 16/32/64-Byte FIFOs

DataCom

Single-port 10/100/1000Base-T Gigabit Transceiver

Development ToolsNu HorizonsInreviumXilinx

Logic

Spartan-6 FPGA Families

Virtex-6 FPGA Families

Power & Battery Management

125Msps ADC at 125mW

1A Micropower Step-Down Switching Regulator

5V RS-485/RS-422 Half-DuplexTransceiverIdeal for Industrial and Remote Data Collection Applications The SP4082E is designed for reliable, bidirectional communication on multipoint bus transmission lines. The device contains one differential driver and one differential receiver. It is a half-duplex device and complies with TIA/EIA-485 and TIA/EIA-422 standards. This device is ruggedized for use in harsh operating conditions over the entire common-mode voltage range from -7V to +12V. Receivers are specially designed to fail-safe to a logic high output state if the inputs are open or shorted. All RS-485 bus-pins are protected against severe ESD events up to ±15kV (Human Body Model). Drivers are protected from excess current flow caused by bus contention or output short-circuits by both an internal current limit and a thermal-overload shutdown. Up to 256 transceivers may coexist while preserving full signal margin.

The device operates from a single 5.0V power supply and draws negligible quiescent power. The device has an independent enable and disable for the driver and receiver and will enter a low power shutdown mode if both driver and receiver are disabled. All outputs maintain high impedance during shutdown or when powered-off.

Bus

Inte

rfac

e

Features Benefits

5.0V single supply operation

Controlled driver slew rates 115kbps

Receiver failsafe on open or shorted lines

1/8th Unit Load

Robust ESD protection for RS-485 pins ±15kV

Human Body Model

Driver short circuit current limit and thermal shutdown

for overload protection

Industry standard package footprint

Low EMI

Higher Density Network

Vigorous ESD protection

Applications

Motor Control

Building Automation

Security Systems

Remote Meter Reading

8 PIN NSOICSP4082E

Half Duplex

1

2

3

4 5

6

7

8

GND

A

B

VccRO

RE

DE

DI

Pin Number Pin Name Pin Function

1 RO Receiver Output. When RE is low and if (A – B) ≥ -40mV, RO is high. If (A – B) ≤ - 200mV, RO is low.

2 REReceiver Output Enable. When RE is low, RO is enabled. When RE is high, RO is high impedance. Drive RE high and DE low to enter shutdown mode.

3 DEDriver Output Enable. When DE is high, outputs are enabled. When DE is low, outputs are high impedance. Drive DE low and RE high to enter shutdown mode.

4 DIDriver Input. With DE high, a low level on DI forces non-inverting output low and inverting output high. A high level on DI forces non-inverting output high and inverting output low.

5 GND Ground

6 A Non-inverting Receiver Input and Non-inverting Driver Output

7 B Inverting Receiver Input and Inverting Driver Output

8 Vcc Positive Supply VCC. Bypass to GND with a 0.1uF capacitor

For more information, including pricing, availability, datasheets and samples (if available), please visit http://uk.nuhorizons.com/FeaturedProducts

Features Benefits

Intel, Motorola or VLIO Bus Interface

20Mbps Maximum Data Rate

Selectable or Programmable TX/RX trigger levels

TX/RX FIFO Level Counters

Independent TX/RX Baud Rate Generator

Fractional Baud Rate Generator

Auto RS-485 Half-Duplex Direction Control

Multidrop Mode w/ Auto Address Detect

PowerSave Mode

1.62V-3.63V Supply Voltage

Automatic Hardware/Software Flow Control

Highest Performance at Lower Supply Voltages

Overall System Cost Reduction

Shorter Time-to-Market

Applications

Smart Phones Personal Digital Assistants (PDAs) Battery-Operated Devices Global Positioning System (GPS) Bluetooth Point-of-Sales (POS) Systems Gaming Systems Industrial Controls

High-Performance Low Voltage UARTs with 16/32/64-Byte FIFOs Smallest and Fastest Single-Channel Universal Asynchronous Receiver Transmitter (UART) SeriesThe XR16M58x/68x/78x series are part of the enhanced Universal

Asynchronous Receiver and Transmitter (UART) family with 16, 32

and 64 bytes of transmit and receive FIFOs. These devices have

selectable or programmable transmit and receive FIFO trigger levels,

automatic hardware and software flow control, and compatible with

the Intel, Motorola, or VLIO bus interface.

Bus Interface

VCC

XTAL1XTAL2Crystal Osc / Buffer

TX , RX,RTS #, CTS#,DTR #, DSR#,

Intel or Motorola

Bus Interface

64 Byte RX FIFORX BRG

IRENDEC

TX & RX

UART

Regs

A2:A0

PwrSave

64 Byte TX FIFO

RI #, CD#

RESET(RESET#)

IOW# (R/W#)

CS#

INT/IRQ#

IOR#

GND

(1. 62 to 3. 63 V)

TX BRG

D7:D0

16/68#

VCC

XTAL1XTAL2Crystal Osc/Buffer

TX, RX,RTS#, CTS#,DTR#, DSR#,

VLIO BusInterface 64 Byte RX FIFORX

BRG

IRENDEC

TX &RX

UART

Regs

LLA#

PwrSave

64 Byte TX FIFO

RI#, CD#

RESET#

AD7:AD0

IOW#

CS#

INT

IOR#

GND

(1.62 to 3.63 V)

TX BRG

XR16M781 Block DiagramXR16M780 Block Diagram

For more information, including pricing, availability, datasheets and samples (if available), please visit http://uk.nuhorizons.com/FeaturedProducts For more information, including pricing, availability, datasheets and samples (if available), please visit http://uk.nuhorizons.com/FeaturedProducts

M E D IAIN TE R FA C E

PM ATX 10/100 /1000

PM AR X1000

PM AR X100

PM AR X10

C lockR eset

P C S10

A U TON EG O TIA TIO N

P C S100

PC S 1000

G M II/R G M II/M IIInterface

LE DD R IVE R S

C onfigurations

Features Benefits

10/100/1000Base-T IEEE 802.3 complianceStandard compliance ensures to work with other standardcompliant, already deployed devices.

GMII, RGMII, and MII MAC interfacesFlexible MAC interfaces (GMII/MII for KSZ9021GQ and RGMIIfor KSZ9021RL) support direct connection to MACs in Ethernetprocessors and switches at various data rates.

Integration of termination resistors on the chipOn-chip termination (eliminating 8 external resistors) not onlysimplifies PCB design and reduces system BOM, but alsoimproves overall signal integrity and EMI emission.

Integration of a LDO controller on the chipIntegration of a LDO controller permits a low cost MOSFET tosupply the 1.2V core, which reduces board cost and simplifiesboard layout.

LinkMD® TDR-based cable diagnosticsBuilt-in LinkMD® diagnostics helps identification of commoncabling problems, including those not addressed by IEEE. Itsimplifies network deployment and reduces network downtime.

Automatic MDI/MDIX crossover for IEEE 802.3 and EIA/TIA 568 standards at all speeds of operation

Auto-MDI/MDIX eliminates the need for cross-over cable,thus reduces installation costs. Easy to use.

Single-port 10/100/1000Base-T Gigabit Transceiver KSZ9021GQKSZ9021RL

The KSZ9021GQ and KSZ9021RL are single-port 10/100/1000Base-T Gigabit transceivers,

supporting data transfer over standard CAT-5 unshielded twisted pair cable. This device offers

robust performance and low power consumption. On-chip integration of termination resistors

and LDO controller, along with built-in diagnostic features, significantly reduces the cost and

the complexity of Gigabit Ethernet applications. This device is ideal for enabling Gigabit Ethernet performance in SOHO and SMB

networking applications, such as media converter, GEPON ONU router, wired/wireless Gigabit SOHO/SMB router, and VoIP gateway.

The device is available in two RoHS-compliant package options - 128-pin QFP (KSZ9021GQ, supporting GMII/MII) and 64-pin E-LQFP

(KSZ9021RL, supporting RGMI). Industrial grade is also available.

Da

tac

om

Block Diagram

Applications

Wired/wireless Gigabit SOHO/SMB Router SOHO Media Center Voice-over-Internet Protocol (VoIP) Gateway Network Attached Storage Laser Printers and Projectors GEPON ONU Router Media Converter VPN/Firewall based SMB/SME Router Gigabit Ethernet LAN on Motherboard Integrated Broadband CPE (ADSL/VDSL/FTTH) Router

LinkMD is a registered trademark of Micrel, Inc.


Spartan-6 FPGA Families The Programmable Foundation for Targeted Design Platforms

The Spartan®-6 family provides leading system integration

capabilities with the lowest total cost for high-volume

applications. The eleven member family delivers expanded

densities ranging from 3,400 to 148,000 logic cells, with half

the power consumption of previous Spartan families and faster,

more comprehensive connectivity. Built on a mature 45 nm

low-power copper process technology that delivers the optimal

balance of cost, power, and performance, the Spartan-6 family

offers a new, more efficient, dual-register 6-input look-up table

(LUT) logic and a rich selection of built-in system-level blocks.

Log

ic

Features

Two Base Platforms

Designed for low cost

Low static and dynamic power

Multi-voltage, multi-standard SelectIO banks

High-speed GTP serial transceivers in the LXT FPGAs

Integrated Endpoint block for PCI Express designs (LXT)

Efficient DSP48A1 slices

Integrated Memory Controller blocks

Abundant logic resources with increased logic capacity

Block RAM with a wide range of granularity

Clock Management Tile (CMT) for enhanced performance

Simplified configuration, supports low-cost standards

Enhanced security for design protection

Faster embedded processing with enhanced, low cost,

MicroBlaze™ soft processor

Low cost, integrated PCI® technology support compatible

across 32 bit and 64 bit, 33 MHz and 66 MHz specifications

Industry-leading IP and reference designs

Learn more about View the webcast at http://www.xilinx.com/events/webcasts.htm.

For more information, including pricing, availability, datasheets and samples (if available), please visit http://uk.nuhorizons.com/FeaturedProducts

The Virtex®-6 family provides the newest, most advanced

features in the FPGA market. Using the third generation

ASMBL™ (Advanced Silicon Modular Block) column-based

architecture, the Virtex-6 family contains multiple distinct

platforms (sub-families). Each platform contains a different ratio

of features to address the needs of a wide variety

of advanced logic designs.

Features

Two Base Platforms

Cross-platform compatibility

Advanced, high-performance, FPGA Logic

Powerful mixed-mode clock managers (MMCM) clocking

36-Kb block RAM/FIFOs

High-performance parallel SelectIO technology

Advanced DSP48E1 slices

Flexible configuration options

System Monitor capability on all devices

Integrated interface blocks for PCI Express designs

RocketIO™ GTX transceivers 150 Mb/s to 6.5 Gb/s

Integrated 10/100/1000 Mb/s Ethernet MAC block

40 nm copper CMOS process technology

1.0V core voltage (-1, -2, -3 speed grades only)

Lower-power 0.9V core voltage (-1L speed grade only)

High signal-integrity flip-chip packaging available in standard or Pb-free package options

Virtex-6 FPGA Families The Programmable Foundation for Targeted

Design Platforms

Log

ic

Learn more about View the webcast at http://www.xilinx.com/events/webcasts.htm.


Features Applications

Full rate CMOS using 14 data lines

Double data rate (DDR) CMOS, 7 data lines

DDR LVDS, 14 data lines, for reduced digital noise

Straight binary or twos complement data coding

Selectable LVDS output current (1.75 to 4.5 mA), to match output current to the load, while minimizing power dissipation

Internal 100-ohm resistors which you can switch in, to absorb reflections due to impedance mismatch at the receiver

A data randomizer which scrambles the output bits via an exclusive-OR circuit, to reduce noise coupling from major signal transitions and improve SFDR (the data receiver, of course, must do a reverse XOR to unscramble them); LTC claims this can reduce residual tones caused by digital feedback by 10-15 dB

Cellular Base Stations

Communications

Instrumentation

Multi-Channel Data Acquisition

Non-Destructive Testing (NDT)

Portable Medical Imaging

Software Defined Radio (SDR)

LTC®2261 — 125Msps ADC at 125mWOne-Third the Power of Comparable High-Speed ADCs

The LTC2261-14/LTC2260-14/LTC2259-14 are sampling 14-bit A/D converters designed for digitizing high frequency, wide dynamic range signals. They are perfect for demanding communications applications with AC performance that includes 73.4dB SNR and 85dB spurious free dynamic range (SFDR). Ultralow jitter of 0.17psRMS allows undersampling of IF frequencies with excellent noise performance.

DC specs include ±1LSB INL (typical), ±0.3LSB DNL (typical) and no missing codes over temperature. The transition noise is a low 1.2LSBRMS. The digital outputs can be either full rate CMOS, double data rate CMOS, or double data rate LVDS. A separate output power supply allows the CMOS output swing to range from 1.2V to 1.8V. The ENC+ and ENC– inputs may be driven differentially or single-ended with a sine wave, PECL, LVDS, TTL or CMOS inputs. An optional clock duty cycle stabilizer allows high performance at full speed for a wide range of clock duty cycles

Power & B

attery Managem

ent

Linear’s newest high-speed ADC family achieves 1/3rd the power consumption of existing solutions without compromising AC performance. Whether operating at full speed or in sleep mode, the LTC2261 significantly lowers the power budget for high-speed data acquisition, making it possible to “cut the cord” and migrate products into the portable world.

–

+INPUT

S/HCORRECTION

LOGICOUTPUTDRIVERS

14-BITPIPELINEDADC CORE

CLOCK/DUTYCYCLE

CONTROL

D13•••

D0

125MHz

CLOCK

ANALOGINPUT

CMOSORLVDS

1.2VTO 1.8V

1.8V

VDD

OVDD

OGND

GND

2-Tone FFT, fIN = 70MHz and 75MHz

FREQUENCY (MHz)0

–100–110–120

–70

–60

–80–90

AMPL

ITUD

E (d

BFS)

–50

–30

–40

–20

–10

0

10 20 30 40 50 60

Typical Application


Features Applications

Wide input voltage range of 3.6V to 36V, with transient protection to 60V

Up to 1A of continuous output current

Up to 90% efficiency

Only 75μA of quiescent current

Adjustable, Synchronizable switching frequency: 250kHz to 2.2MHz

DA pin to permit the OVLO at any operating frequency

Output is adjustable down to 0.8V

Soft-start capability

Power Good Flag

Tiny 3mm x 3mm DFN-12

Automotive Battery Regulation

Automotive Entertainment Systems

Industrial Supplies

Power for Portable Products

Distributed Supply Regulation

LT3682 - 1A Micropower Step-Down Switching Regulator 36V

IN (60V Transient Protection) 1A,

Micropower Step Down ConverterModern automobile, industrial and telecomm environments continue to include increasingly complex electronic systems. Additionally,

these electrical and physical environments continue to be very harsh for any type of electronics. Wide operating voltage requirements

coupled with large transient voltages and wide temperature variations combine to make life difficult on electronic systems. High efficiency

is of paramount importance as it minimizes thermal design considerations while also maximizing battery run time. Equally important is

very low quiescent current which minimizes the power drawn from a battery when the IC is in a standby mode. Many of these applications

operate from batteries, or utilize back-up batteries, in which a voltage rail must be maintained with no load current for an extended

period of time. Therefore, it is important to keep the quiescent current as low as possible. Common applications are automotive GPS,

security and environmental control systems as well as a myriad of industrial applications. Additionally, as manufacturers increase the

electronic content of their systems, the space

requirements continue to shrink demanding

smaller and more efficient power solutions.

The New Direction:

Linear Technology adds the LT3682 to its existing

family of high voltage Micropower monolithic

step-down converters to specifically address

these requirements. The LT3682 provides an

extremely compact 36VIN step-down solution

with transient protection to 60V. The device

provides improved performance in all key areas

including size, efficiency, ease of design, as well

as excellent thermal performance.

Power & B

attery Managem

ent


Nu Horizons Spartan™-3A Evaluation Kit

Inrevium VirtexTM-5 PCI Express Evaluation Board

Dev

elo

pm

ent

Too

ls

Nu Horizons offers a wide range of development/evaluation boards, tools and kts. For more information, please visit http://uk.nuhorizons.com/development

2x16Character Display

1 MB SRAM

SPIFlash

Pushbuttons8 LEDs

Headers

JTAG Header

XC3S200A FPGA

RS-232 50 MHz Crystal

USB

This low cost board features the new Spartan-3A Platform FPGA from Xilinx. The Spartan-3A Platform is perfect for applications where I/O count and capabilities matter more than logic density like bridging, differential signaling and memory interfacing applications, requiring wide or multiple interfaces and modest processing.

Key Features: Xilinx XC3S200A-4FTG25CES FPGA Linear Technology LTM4603 DC to DC power supply USB port 16x2 Tianma display 1 M ISSI SRAM LT1331 – Linear Technology 3V RS562 or 5V/3V RS232 transceiver LT1962 – Linear Technology 300mA, low noise, micropower LDO regulator LT3021 – Linear Technology 500mA, low voltage, very low dropout linear regulator LT4413 – Linear Technology Dual 2.6A, 2.5V to 5.5V fast ideal diodes LTM4603 – Linear Technology 6A DC/DC μModule with PLL, output tracking and margining

Ordering Info: NH-SPAR3A-EVL

Price: $125 (Use Promo Code 0309SP3A online for 20% off)

DC12V

Jumper

10pinPin Headers

XCF32PVO48

JTAG Port

DDR2 SDRAM(Chip)

DDR2 SO-DIMM

SMA x2

42pin I/O Expand x1

LX110T MGT Connector (4ch)

Camera_link

LX110T 42pin I/OExpand x2

SFP x2RS232C

MICTORConnector

Push SW (x4)

XilinxXC5VL50T/110T

-1FF1136

PCI-Express x8

LED (x8)

DIP SW (x8)

LXT110TPin Header

3.3V

2.5V

1.8V

1.2V

1.0V

0.9V Flash ROM

PHY

RJ45

TB-5V-LX-xxxT-PCIEXP is an ideal High-speed evaluation platform for 8-lane PCI-Express. In addition, it supports multiple High-speed serial transceiver interfaces with SFP and SMA connector ports. On-board Camera Link port is useful for a wide variety of video applications such as image processing. This Inrevium board product is produced by Tokyo Electron Device.

Ordering Info: TB-5V-LX50T-PCIEXP Price: $2,980 TB-5V-FX70T-PCIEXP Price: $4,980 TB-5V-FX70T-PCIEXP-512 Price: $5,060 TB-5V-LX330T-PCIE-EX Price: $14,980 TB-5V-SX240T-PCIE-EX Price: $19,800 TB-5V-FX200T-PCIE-EX Price: $11,980

by Tokyo Electron Device Ltd. Key Features:

FPGA: XC5VLXT 50/110 FF1136 PCI-Express V1.1 x8 DDR2 SDRAM chip: 512Mb x1 DDR2 SO-DIMM Slot x1 10/100/1000Mbps Ethernet MAC & PH CameraLink port x1 SMA connector x2 SFP x2

LTC1348 – Linear Technology 3.3V/5V low power RS232 3-driver/5-receiver transceiver LTC3413 – Linear Technology 3A, 2MHz monolithic synchronous regulator for DDR/QDR memory termination LTC3728 – Linear Technology Dual, 550kHz, 2-phase synchronous step- down switching regulator LTM4600 – Linear Technology 10A DC/DC μModule power supply

,

Nu Horizons Virtex™-5 LXT Evaluation Platform

Inrevium Virtex™-5 SXT High-Speed Computing Platform

De

velo

pm

en

t Too

ls


by Tokyo Electron Device Ltd.

Key Features: 10/100/1G Marvell Ethernet Phy LTC1326 – Linear Technology micropower precision triple supply monitor LTC3026 – Linear Technology 1.5A low input voltage VLDO linear regulator LTC3412 – Linear Technology 3A, 4MHz, monolithic synchronous step-down regulator LTC3418 – Linear Technology 8A, 4MHz, monolithic synchronous step-down regulator LTM4601 – Linear Technology 12A DC/DC μModule power supply 2x16 Tianma display ISSI DDR2 SDRAM 1 SFP connector 8 SMA connectors

Includes: Development board Power supply Reference design

Ordering Info: NH-5VLXT-EVL

Price: $799

MarvellEthernet Phy

RS-232 1 SFP8 SMAsCrystal

Platform Flash

JTAG Header

Headers

Linear TechAcquisition Header

16 MB Flash

64 MB DDR

Xilinx VirtexLXT50

Pushbuttons8 LEDs

Video DAC


The Virtex-5 LXT Platform FPGA is optimized for high-performance logic with low-power serial connectivity. This kit includes one of SPF and 8 SMA connectors for easy evaluation of MGT designs.

This new platform from the Tokyo Electron Device engi-neering team is designed specifically for computational intensive designs. Each 5VSX95T devices is connected to each of the other 3 devices by four dedicated GTP chan-nels for high speed communication between the devices.

Key Features: XC5VSX95T-1FF136 x4 DDR2 SDRAM x8 GTP x16 ch per FPGA X4 to each FPGA X4 SAMTEC connector Samtec High Speed Interface (120 pin) x1 per FPGA Optional Expansion capabilities x1 per FPGA

Includes: Evaluation Board Documentation Power Supply

Ordering Info: TB-5V-SX95T4-HSC

Price: Call Nu HorizonsDDR2

SDRAM

SX95T

DDR2 SDRAM

DDR2 SDRAM

SX95T

DDR2 SDRAM

DDR2 SDRAM

SX95T

DDR2 SDRAM

DDR2 SDRAM

SX95T

DDR2 SDRAM

This low cost evaluation kit from Nu Horizons is designed to help evaluate the new Spartan 3ADSP FPGAs from Xilinx. Peripherals include memory, analog circuitry, and a short range RF link.

Key Features: XC3SD1800A-4FGG646C Spartan-3A DSP FPGA 16 MB DDR2 SDRAM 16 MB SPI Flash 10/100 Ethernet PHY 14 bit Analog to Digital Converter Radio Transceiver Stereo DAC Video DAC 20x2 character LCD Display

Includes: Evaluation Board Documentation Power Supply

Ordering Info: NH-SPAR3ADSP-EVL

Price: $199.99

XC3SD1800ACS484

2x20 Display Pushbuttons

RS-232 Crystal

16 MB DDR2 SDRAM

10/100 Ethernet Phy

16 MB SPI Flash

Video DAC

Stereo DAC

LTC FastDAACConnector

RF Radio

8 LEDs

14 bit ADC

The Virtex-5 FXT Platform FPGA is optimized for high-performance logic with low-power serial connectivity. This kit includes one of SPF and 8 SMA connectors for easy evaluation of MGT designs.

Key Features: 5VFX30T FPGA 10/100/1G Marvell Ethernet Phy LTC1326 – Linear Tech micropower precision triple supply monitor LTC3026 – Linear Tech 1.5A low input voltage VLDO linear regulator LTC3412 – Linear Tech 3A, 4MHz, monolithic synchronous step- down regulator LTC3418 – Linear Tech 8A, 4MHz, monolithic synchronous step- down regulator LTM4601 – Linear Tech 12A DC/DC μModule power supply 2x16 Tianma display Micron DDR2 SDRAM 1 SFP connector 8 SMA connectors

Ordering Info: NH-5VFXT-EVL

Price: $849

Nu Horizons Spartan™-3A DSP Evaluation Kit

Nu Horizons Virtex™-5 FXT Evaluation Platform

Dev

elo

pm

ent

Too

ls

MarvellEthernet Phy

RS-232 1 SFP8 SMAsCrystal

Platform Flash

JTAG Header

Headers

Linear TechAcquisition Header

NAND Flash

64 MB DDR

Xilinx VirtexLXT50

Pushbuttons8 LEDs

Video DAC



Enhance Your Design...With Nu Horizons Education and Development Solutions

LabCam delivers online training opportunities in a way that recognizes the value of engineers’ time. As easily as You Tube® videos, engineers can quickly load and watch videos from industry leaders consisting of insights on products, evaluation kit overviews, end-user applications and more. Each tutorial is up to ten minutes in length and features technology experts, CEOs and/or peers introducing new solutions or explaining integral aspects of an important product, solution or application. This free value-added program is packaged for short, informative and high quality distance learning.

Nu Horizons is proud to present our education and training program, which offers engineers the opportunity to participate in technical seminars conducted by experts focused on the latest technologies from our leading suppliers. This program provides higher velocity learning to help minimize start-up time to quickly begin your design process utilizing the latest development tools, software and products. Check online for the latest seminar schedule.

In order to simplify the design process, Nu Horizons has created a series of application notes designed to guide engineers through the process of interfacing different devices together. Using a detailed step-by-step approach, these design guides identify key elements in the design process. Topics in the application notes are organized by design task and each topic is a stand-alone section, with a short introduction or overview, followed by the step-by-step design guidelines. All steps include a sufficient level of detail to provide the designer with relevant information to proceed quickly and easily from start to finish.

Nu Horizons offers a wide range of development / evaluation boards, tools and kits featuring the latest technology from the most trusted suppliers in the industry. Visit the development tool section of our website for a variety of solutions all aimed at providing a low-cost solution for designers to accelerate a product’s time-to-market.

http://uk.nuhorizons.com/labcam/

http://uk.nuhorizons.com/FeaturedProducts

http://uk.nuhorizons.com/seminars/index.asp

www.nuhorizons.com/olc

www.nuhorizons.com/appnotes

Application Notes

Online Learning Center

DevelopmentToolshttp://uk.nuhorizons.com/development/

Portal is a monthly publication containing new products, technologies and development tools available from Nu Horizons leading suppliers. Portal is availabe both in print and on the web. Sign up online to receive your copy, be notified of upcoming issues or to request samples of the products found inside.

Nu Horizons Online Learning Center is designed to provide a complete training experience for engineers — without having to leave the office. New supplier trainings are posted twice a month and range from new product overviews to in-depth technical training and potential design implementations. These live trainings are recorded and archived for your viewing convenience.

Nu Horizons Electroncis Portal - Europe

Documents

Transcript of Nu Horizons Electroncis Portal - Europe