City of Aurora Building Division 15151 E Alameda Pkwy Aurora, CO 80012 (303) 739-7420 _____________________________________________________

Notice

This material is subject to copyright protection pursuant to Federal Law: 17 United States Code Section 106.

Building Permit Application Permit Center ..... 15151 E Alameda Pkwy ..... Aurora, CO 80012"" (303) 739-7420

Project Address: '4"3>!;)c> E I\lf.\(\'\\:DI\ 1\'Vr.. . Unit # Zip code: 1(3 O() l'Z...

Contractor Company Name: WC .... 'i:gN Sl~l~=:' FlRf P~fcif.L'\Sr:.J Phone: ~\)1-"S-z - oo'Z.z Fax: "'303·''~"\4 - C)O'-l,\ Contact Person: :Sbr'~ ('),,~ ~\ Email: SO."\NqDt.e S\ @ W S~p, '" S

Online Services now offers email updates of correction items found during plan review as well as email updates for all inspections during the construction phase of your project. If you are interested in receiving these emails please provide your email address. NOTE: Set

Our email fi lter to acce t emails from "AmandaS stem". Plan Corrections - Email address: 30\-\ N . \'{o"S T \ Inspection Corrections - Email address: S {\('\.-\\:._

Architect and/or Engineer Contact information for correction items:

Architect or Engineer name: Email: Phone # Fax:

Owner: (Reguired for CO) only: Owner address: Valuation / FDA:$

Email: Materials Cost: $ \'Z 80

FDA = Fee Determination Assessment. (Also known as the value of project) has no relationship to the construction costs for the building which can vary greatly. Rather, The assessment is used only to determine the appropriate level of fees to fund our code compliance activities. Architect or Engineer Name: Email:

DESCRIBE THE WORK YOU WILL BE DOING:

I declare under penalty that this application has been examined by me and that the statements made herein are made in good faith pursuant to City of Aurora tax and licensing regulations' and to the best of my knowledge and belief are true correct and complete , , Print Name: _ \-\

D~o'S\ Signature: /'f~ I)~ Date: ,Z " f '-\-z. ~o N

BOARD OF APPEALS - Contractor's Appeals and Standards Board. Applicants ~ve the right to have the board hear appeals of orders, decisions or determinations made by the building official relative to the application and interpretation of the building code. Any application for appeal to the board shall be based on a claim that the true inte(1t of the code or the rules legally adopted there under have been incorrectly interpreted , the provisions of the building code do not fully apply or an equally good or better form of construction is proposed.

S~inkler & Alarm permits must be brought in as separate submittals. "FDA" is NOT included in main 'permit •

•••• THIS SPACE FOR OFFICE USE ONLy ••••

Fee Determination Assessment: $ ::t;J YO,r-Q-J Pre approval Initial

Zoning D Change of occupancy/use: Y D N D Water D REVIEWS INSPECTIONS Exterior changes? DYes D No

Homeowner verified DYes

D Structural 0 Structural Permit Type: L 'I D Mechanical 0 Mechanical Mid roof / Ave Bldg Height;-'!ff-

0 Plumbing 0 Plumbing Parent Permit RSN: GXJr;'Y7 0 Electrical 0 Electrical Plans Examiner: CJ() ~

0 Fire Life Safety 18- Life Safety Subtype: y;;< h "'Y1-l+/~.Y f'L-l

0 Bldg Life Safety 0 Gate/Haz. RSN: 1p!j.3 {J23 Intake Date: PE Initial

Plans Picked up by: Balance Due: Company name:

Phone number:

Western States Fire Protection Co.

December 7, 2012

To: City of Aurora

7026 S. Tucson Way. Centennial, CO 80112

(303) 792·0022 (303) 792·9049 FAX

Building Codes Division 15151 East Alameda Parkway, 2'" Floor Aurora, Co 80012 303-739-7420

Firt Ptot.ction Systems Qto!gn. febrl"Uoo, 'DII,blW

Commtrdal . EndUllrlal • "-"MntlI1 . lnItllutiontl Specl~ Hawd • • HIgh Tectl . 0,1_ . Hang.,.

R"lOfII . ~k;e • • ,...,..100 ' Malnt __

RE: Scope of work for addition of addressable modules for projector shunt at the Century 16 Theaters in Aurora.

Address: Century Aurora 16 14300 E. Alameda Ave. Aurora, CO 80012

This is a scope letter for adding addressable relay module to existing Notifier AFP-1010 fire alarm control panel. The building's projectors are being modernized to shut down the film and turn on theater lighting to provide ease of egress during a fire alarm condition. The new relay will be wired from existing circuit that is currently in the projector equipment room, and will activate during general fire alarm.

Attached are data sheets of the existing fire panel and the added addressable relay module.

Please do not hesitate to call me with any question you may have.

Sincerely,

John Drost Fire Alarm Systems, Level: III Technician 10: 128938

Alarm & Detection Division Office: 303-792-0022 Ext#5209 Mobile: 303-549·9016 Fax: 303-790-3874

ALBUOVE"OUE , NM. AUSTIN , lX , • CALL"S , TX • DECATUR, I I. • OE N VER , CO . HOU STON , TX. KANSAS C I TY , KS .. MI NN E APOL IS. UN • PHOENI X, AZ PORTI,. ... ND. OR. RAP ID CI TY . SO . 5"I.T LAKE CITY , UT. SEATTle WA. ST , LOU I S. MO . TULSA. OK

~~NOTIFIER· ~ ~ FIRE SYSTEMS

GENERAL The AFP1 010 is an intelligent, addressable, fire alarm con­trol panel with the capacity for 792 individually identifiable and controllable detection/control paints. The modular hardware design and easy-to-define system operation soft­ware allows the user to easily configure the AFP1 01 0 in the field.

The AFP1010 is UL Listed under the following Standards: UL 864 Control Units for Fire Protective Signaling Syslems; UL 1076 Proprietary Burglar Alarm Units; and UL 1610 Central Station Burglar Alarm Units. The AFP1010 also meets the requirements of NFPA Local, Auxiliary, Remote Station, Proprietary, and Emergency Voice/Alarm Fire Sys­tems.

Addressable/intelligent detectors help fire-fighting person­nel quickly locate a fire during its early stages.

FEATURES Completely field-programmable and configurable, no computer programming skills required. System contin­ues to provide fire protection while program is being ed­ited. System capacity: 396 intelligent detectors plus 396 moni­tor/control modules (792 total points) and 240 software zones, plus 2,048 annuncialor/control points. Intelligent (Analog) Detectors: Ionization, Photoelectric, Thermal (with or without Rate-of-Rise feature), and Multi­sensor (Ion, photo, and heat in same head). Intelligent photoelectric duct detectors. Addressable initiating modules to monitor normally open or normally closed contacts. NOTI-FIRE-NET- interface provides a peer-to-peer high speed network (see data sheet DN-4(44). Upload/download of all program information to a PC com­patible computer. VeriFire TM software utility - create, edit, check, simulate by association, and compare panel databases (Win­dowS® 95/98 compatible). SCS-8 smoke control option (NFPA 90A, 92A & B listed dedicated or non-dedicated systems). Aulomatic drift compensation of intelligent smoke detec­tors (UL Lisled). Automatic system test activates and verifies (17 cycles in a 24-hour period) every detector in the system. Meets the calibrated test requirements of NFPA 72 (UL Listed). Detector sensitivity adjust: manual or automatic (day/ night).

July 17. 2000 DN-3341 - A-1 02

AFP10l0 Intelligent Fire Detection

and Alarm System Section: Intelligent Fire Alarm Control Panels

®@<S>.~~ LISTED CS118 -(a~~~::!::for ~

S635 CS733 aulomatic release and S5511 pre-action deluge)

u_s_ Coast Guard

161.002127/1

93160140 (E1)

I California • ~ State Fire Marshal 7165-0028:141 7170-0028:153 USTED

The AFP1010 (shown in CAB·A3 cabinet)

Maintenance Alert function automatically warns of con­taminated detectors. Walk test with counters per point and identification of two detectors set to same address. Automatic abort timer. Alarm verification, with verification tally counter, per in­telligent detector. Also included is a programmable de­tector verification limit check. Addressable dry-contact relay modules and supervised Notification Appliance circuit modules. Modular hardware design with plug-in terminal blocks. Multiple microprocessors with degraded operation mode in the event of a CPU failure. 20-character custom alpha/numeric descriptive labels for each system point and software zone.

NOTI-FIRE-NET"" Is a lrademark of NOTIFIER, 1994. Wlndows® is a regislered trademark of Microson Corporalion.

This document Is not Intended to be used for InstaUatlon purposes We tty to keep our product Informatlon up-to-date and accurate. We cannot cover an spec,fic appl cations or anticipate all requirements. All specifications are subject to change without nollCe. For more Information. contact NOnFIER. Phone: (203) 484~7161 FAX: (203) 484·711 8

@l NOTIPIER- One Flre·U', Piece. Northford. ConnecUcu. 06472

ISO 9001 Made In the U.S A.

DN·3341 ·07/17/00 - Page 1 of 4

Powerful control-by-event function: - Point and/or zone. - AND/OR/NOT function. - TIme equations. - Tracking/latching selections. - Pulse timers. Non-Alarm points (lower priority) for security, energy man­agement, or lighting functions. Control-by-time functions for time and date actuation of outputs. Programmable time delays and pulse functions. User-selectable sensitivity settings per detector. 400-event history log stored in nonvolatile memory with display, scroll, and print features. Real-time nonvolatile clock for time and date stamp of all events. Optional multiple assignable passwords. Disable/Enable per addressable device or software zone. Status report (several types of reports) for all devices in system, including detector sensitivity and verification tally. UZC-256 universal zone coder (positive non-interfering successive) module (see UZC-256 data sheet). ACM-BR remote relay module extends AFP1010 point capacity (see ACM-BR data sheet). Software timers for silence inhibit, alarm cutout, and alarm verification. High-speed EIA-4B5 annunciator/control interface. BO-character alphanumeric Supertwist LCD display with built-in backlighting. Remote alphanumeric annunciator option (LCD-BO). 30-key tactile keypad with full alphabetic capability. Remote CRT terminal option with alarm and trouble counter. Multiple remote 40-column and BO-column printer options. Block acknowledge of troubles and auto trouble restora­tion. Trouble reminder option (programmable). XP or XP5 transponders for large multiplex systems (see XP or XP5 data sheet). ACS serial remote annunciator control systems (see ACS data sheet). LDM modules for custom annunciators and control re­lays. Extensive transient protection. Rapid polling algorithm for manual station response in under five seconds (first 20 addresses). Pre-Alarm option (programmable) for advanced waming of false alarm conditions. Marine agency approved. UDACT Universal Digital Alarm Communicator Transmit­ter. Transmits up to 204B points to a central station (see UDACT data sheet).

PRODUCT LINE INFORMATION BE·1010N: Base equipment for AFP-1010. Includes CPU-2, DIA-1010, ICA-4L, manuals, cables, and miscella­neous hardware.

CPU.2: The Central Processing Unit is the director of all system communications and operations. The CPU-2 stores all of the system's operational parameters (which are pro­grammed in the field) in nonvolatile memory. The CPU-2 also provides a Form-C alarm contact and a Form-C trouble

Page2of4 - ON·3341·07/17/00

contact. Communications with LIB, SIB, and DIB boards are over a high-speed serial interface. Removal, discon­nection, or failure of any control panel board is detected and reported by the CPU-2. This module contains and ex­ecutes all control-by-event programs for specific action in response to an alarm condition.

Control-by-event programs are held in the nonvolatile pro­grammable memory.

DIA.1010: The Display Interface Assembly consists of a hinged door; a 30-key keypad; an BO-character liquid crys­tal display (backlit); and a Display Interface Board (DIB).

The keypad has controls for ACKNOWLEDGE/STEP; SIG­NAL SILENCE; SYSTEM RESET; SYSTEM TEST; LAMP TEST; READ STATUS; ALTER STATUS; PROGRAM; SPE­CIAL FUNCTION; BACK SPACE; ENTER; numeric keys 0

D713d,.2,wmf

o .NTIIl .... IO.NT ., .. e OIllTII!ICTlgN AND ALa."M .,..TIlM

llIalilUI llIallll!!! lIaalll:!! IlII!!1 II III 1:1 BII!I III Inl

- 9; plus alpha enter and alpha keys A - Z. PRIOR, NEXT, and AUTOSTEP keys speed readout of status information. It has LED display for System Alarm; System Trouble; Dis­play Trouble; AC Power; and Signals Silenced. The LCD display has BO characters in two lines of 40 characters each. It is capable of displaying all status information, including: Type of Event (6 characters); Type of Device (12 charac­ters); Custom Point Label (20 characters); Custom Zone Label (20 characters); TIme and Date (14 characters); and Point Number (3 characters).

The DIB includes nonvolatile memory for all custom labels and passwords. The DIB provides integral status and pro­gramming functions using interactive menu displays on ei­ther the LCD display or the CRT terminal. All program ed­iting may be achieved without special equipment and with­out interrupting AFP1010 alarm monitoring.

The DIA-1010 includes an RS232 interface for a printer and an EIA-4B5 interface for the LCD-BO (terminal mode). Up to 32 LCD-BO displays may be installed, each with ACK, SILENCE, and RESET switches.

LIB·400: The Loop Interface Board communicates with up to 19B intelligent detectors and 19B addressable mod­ules over two Signaling Line Circuits (SLCs). LlB-400 pic­tured at right. See Common LIB Features below.

LIB·200A: The Loop In­terface Board communi-cates with up to 99 intelli- " gent detectors and 99 ad­dressable modules over a Signaling Line Circuit (SLC).

Common LIB Features: All operating power, as well as high-speed two­way data communication, are made through a pair of

G

"

, • el

0' e. •

• •

wires called the SLC loop. This SLC loop may be wired to function like a Style 4, or Style 6 circuit. The SLC loop may be up to 12,500 feet (3,810 meters) in length if 12 AWG (3.25 mm') wire is used (smaller gauge for shorter dis­tances). If the ISO-X module is used between each zone of devices, the LlB/SLC can function like a Style 7 circuit. The LIB is normally controlled by the CPU, but includes Local Mode software that will provide degraded operation in the unlikely event of CPU failure. A general alann bus between LIBs functions in the event of a CPU failure. This bus allows all programmed local mode points to operate as a common alarm when programmed.

All wiring from the Loop Interface Board is power limited per UL requirements, and connected with plug-in terminal blocks. All connections may be made to these terminal blocks, allowing for the identification and corrections of any field wiring faults prior to the final connection of the tenni­nal blocks to the Loop Interface Board.

SIB·2048A: Serial Interface Board provides the follow-ing interfaces: 07llalbl ,wm/

Dual EIA-232 terminal 0 • I ports (2400 baud, ASCII) 0't • I I i for CRT, and other EDP- ~I~o " •• ' ..,. : listed devices. I

OIIal EIA-232 prinler port • iO> • for PRN Printer, VGAS, • I ..,. and other EDP-listed de- ~ g vices. I • .J. :' ..,. . EIA-485 annunciation • ~ : ports (20 K baud, ASCII) I . ' I I I for ACS annunciators, AMG, and Network Interface Board.

The SIB-2048A has full optical isolation on the EIA-232 interfaces to avoid ground-fault problems with EOP-listed devices. All tenninal blocks plug-in to simplify installation and service.

SIB·NET: Network interface board for NOTI· FIRE ·NET (see separate data sheet).

MPS·24A: The Main Power Supply mounts in the lower left of the cabinet, and provides the following capabilities:

Eleclrically regulaled syslem power supply (24 VOC and 5 VOC). Resettable electrically regulated power for four-wire de­tectors. Non-reseUable electrically regulated power for indicat­ing appliances andlor ACS annunciators (3.0 amps). Dual-rate battery charger for gell-cell batteries (up to 55 AH) and NiCad cells up to 32 amp hours (NiCads mount external). Ground (earth) fault detection, with LED display. AC faillbrownout detect and battery switchover, with LED indicator. 120 VAC and 240 VAC (MPS-24AE) options with circuit breaker and transient protection. PTC power limiting and overload protec­tion on all outputs. Switched regulation for high efficiency and low power dissipation.

True battery supervision. Power-saver charger shutdown in alann. Compatible with CHG-120 extemal 120 amp-hour bat­tery cabinet and charger. Deep baUery discharge pre-vention.

APS·6R: (pictured at righf) Auxiliary Power Supply (ex- -pander). Provides up to 6.0 am- .J peres of regulated power for :: compatible notification appliance circuits. Includes battery input and transfer relay, and overcur­rent protection. Mounts on one of four positions on a CHS4L or CHS4 chassis.

MBT·t: Municipal Box Trip for NFPA 72 auxiliary applications. Use in conjunction with one CMX module and one A77-716B power if n'r ;r Y .7 supervision relay.

CHS·4: (at right) Chassis, four position. Use for APS-6R modules.

1 "

I Dp·t: Blank dress panel. Use to cover unused rows in cabinet, or CHS4/CHS4L chassis.

CAP·t: The CAP-l capacitor is used to filter-out high­frequency AC interference between Earth Ground and Sys­tem Common within the same cabinet (one per power sup­ply).

CAB·3 Series Cabinets: (see data sheet DN-3549 for cabinet options).

SECURITY' EQUIPMENT RKS·1 Remote Keyswitch

5TS·l Security Tamper Switch

CONSTRUCTION The basic equipment for the AFP10l0 is the BE-l0l0N, which includes one OIA-l010; one CPU-2, and one ICA-4L. SIB and LIB boards are then plugged into ICA-4L chas­sis and an MPS Series power supply is installed in the cabi­net. The maximum AFP includes 2 LlBs and 1 SIB, and will fit in the CAB-A3 enclosure. Larger enclosures may be ordered if desired for additional power supplies, XP tran­sponders, etc. Each cabinet includes space at bottom for power supply and up to 25 amp hours of batteries. The BB-55 and cabinet may be used for 55 AH balleries.

ELECTRICAL SPECIFICATIONS Primary input power: 120 VAC, 50/60 Hz. Primary input power: 240 VAC, 50/60 Hz. Add an "Eo to end of the model number (example: MPS-24AE). Primary AC power supervision with automatic switcho­ver to supervised standby batteries.

ON·3341·07/17/00 - Page3of4

AGENCY LlmNGS AND APPROVALS See the first page of this data sheet for listing agencies and file numbers. These listings and approvals apply to the basic AFP1010 control panel. In some cases, certain modules may not be listed by certain approval agencies, or listing may be pending. Consult factory for latest listing status.

ARCHITECTURAL/ ENGINEERING SPECIFICATIONS Specifications are available on CD-ROM with NOTIFIER's Speci-Fire1M software. Contact NOTIFIER for details; httpllwww.notlfiar.com.

COMPAnBLE INTELUGENT DETECTORS FSI-751 FSP-751

Ion detector. Photo detector.

FSP-751T Photo detector with fixed thermal element. FST -751 Thermal detector, fixed. FST-751R Thermal detector, fixed and rate-ol-rise. IPX-751 Advanced multi-criteria deteclor (ion/photo/

thermal). HPX-751 HARSH 1M photo detector (requires special

base). FSD-751 P Duct detector, with housing. FSD-751 RP Duct detector, with housing and relay.

INTELLIGENT DETECTOR BASES B710LPBP Standard flanged base, package 01 ten. B510BP Standard flangeless base, package of ten. B710HD Base for HPX-751 (HARSH'") only. B224RB Relay base.

B224BI Isolator base. B501 BH Sounder base.

B501 BHT Sounder base with temporal sounder.

Page 4 of 4 - DN·3341 ·07/17/00

COMPATIBLE ADDRESSABLE DEVICES NBG-12LX Addressable pull station, visible LED. FMM-1 Monitor module. FMM-101 Monitor module, miniature.

FDM-1 Monitor module, dual, two independent Class B circuits.

FZM-1 FCM-1 FRM-1 XP5-M

XP5-C

ISO-X

Monitor module, two-wire smoke detectors. Control module. Relay module. Transponder, monitor, five addressable Class B circuits. Transponder, control/relay, five addressable Class B circuits. Isolator module.

COMPATIBLE EIA·232 DEVICES CRT-2 CRT terminal with keyboard. VS4095/5 40 column, 24 VDC printer. PRN Series BO-column printer.

COMPATIBLE EIA·485 DEVICES (see separate data sheets)

ACS Series LCD-80

LDM Series UZC·256 ACM-8R RPT-485W

RPT-485WF

SCS Series UDACT

Remote serial annunciator/control systems. Liquid Crystal Display (connect to terminal mode EIA-485 on DIA-1010). Remote custom graphic driver modules. Universal Zone Coder. Remote Relay Module. EIA-4B5 Repeater board. Twisted-pair con­nection. EIA-4B5 Repeater board. Allows a twisted­pair in and fiber optics out. RPT -4B5F's must be used in pairs. Smoke Control Modules. Universal Digital Alarm Communicator Transmitter.

FCM·1 (A) & FRM·1 (A) Series Control and Relay Modules

General FCM-l(A) Control Module: The FCM-1(A) Addressable Can· trol Module provides Notifier intelligenl fire alarm control pan· els a circuit for Nolification Appliances (horns, strobes, speakers, etc.). Addressability ellows the FCM-1(A) to be actio vated, eilher manually or through panel programming, on a select (zone or area of coverage) basis.

FRM'l(A) Relay Module: The FRM-1(A) Addressable Relay Module provides the system with a dry·contact output for acli· vating a variety of auxiliary devices, such as fans. dampers. control equipment, etc. Addressability allows the dry contact to be activated, either manually or through panel programming, on a select basis.

FlashScan® (U.S. Patent 5,539,389) is a communication pro· tocol developed by NOTIFIER Engineering that greatly enhances the speed 01 communicalion between enalog Intelli· gent devices. Intelligent devices communicate In a grouped fashion. 11 one of the devices within the group has new infor· mation, the panel CPU stops the group poll and concentrates on single points. The net effect is response speed greater than five times that of other designs.

Features • Built·in type identification automatically idenlifies these

devices to the control panel. • Internal circuitry and relay powered directly by two·wlre

SLC loop. The FCM-1(A) module requires power (for horns, strobes, etc.), or audio (for speakers).

• Integral LED "blinks" green each time a communication Is received from the control panel and turns on in steady red when activated.

• LED blink may be deselected globally (affects all devices).

• High noise immunity (EMF/RFI). • The FCM-1 (A) may be used to switch 24-voll NAC power.

audio (up to 70.7 Vrms).

• Wide viewing angle of LED. • SEMS screws with clamping plates for wiring ease. • Direct·dial entry of address 01 - 159 for FlashScan loops,

01 - 99 for CLIP mode loops. • Speaker, and audible/visual applications may be wired for

Class B or A (Style V or Z).

Applications The FCM-1 (A) is used to switch 24 VDC audiblelvisual power, high·level audio (speakers). The FRM-1(A) may be pro· grammed to operate dry contacts for applications such as door holders or Air Handling Unil shutdown, and to reset four·wire smoke detector power. NOTE: Refer 10 Ihe SLC Manual (PN 51253) for delails regarding releasing applications wilh Ihe FCM- l(A). Refer 10 Ihe FCM-I-REL dalasheel (DN-6D39D) for new FlashScan® releasing applications.

Construction • The face plate is made of off·while heat·reslstant plastic. • Controls include two rotary switches for direct·dlal entry of

address (01-159).

DN-6724:B3

~NOTIFIER® by Honeywell Intelligent I Addressable Devices

FCM-l(A)

• The FCM-1(A) Is configured for a single Class B (Style V) or Class A (Style Z) Notification Appliance Circuit.

• The FRM-l(A) provides two Form·C dry contacts that switch together.

Operation Each FCM-1 (A) or FRM-1 (A) uses one of 159 possible module addresses on a SLC loop (99 on CLIP loops). It responds to regular polls from the control panel and reports lis type and status, including the open/normaVshort status of ils Notifica· tion Appliance Circuit (NAC). The LED blinks with each poll received. On command, it activates Its internal relay. The FCM'l(A) supervises Class B (Style V) or Class A (Style Z) notification or control circuits. Upon code command from the panel, the FCM-1(A) will dis· connect the supervision and connect the external power sup­ply In the proper polarity across the load device. The disconnection of the supervision provides a positive indication to the panet that the control relay actually turned ON. The external power supply is always relay isolated from the com· munication loop so that a trouble condilion on the external power supply wi l never interfere with the rest of the system.

Rotary switches set a unique address for each module. The address may be set before or after mounting. The buill·in TYPE CODE (not sellable) will Identify the module to the con­trol panel, so as to dillerenliate between a module and a sen· sor address.

Specifications for FCM·1 (A) Normal operating voltage: 15 to 32 VDC.

Maximum current draw: 6.5 mA (LED on).

Average operating current: 350 ~A direct poll, 375 ~A group poll with LED flashing, 485 ~A Max. (LED flashing, NAC shorted.)

DN·6724:B3· 2/1712011 - Page 1 of 2

Maximum NAC line loss: 4 VDC.

External supply voltage (between Terminals no and Tt 1): Maximum (NAG): Regulated 24 VDC; Maximum (Speakers): 70.7 V RMS, SOW.

Drain on external supply: 1.7 mA maximum using 24 VDC supply; 2.2 mA Maximum using 80 VRMS supply.

Max NAC Current Ratings: For class B wiring system, the current rating is 3A; For class A wiring system, the current rat· Ing Is2A.

Temperature range: 32'F to 120'F (O'C to 49"G).

Humidity range: 10% to 93% non·condenslng.

Dimensions: 4.5' (114.3 mm) high x 4" (101.6 mm) wide x 1.25' (31 .75 mm) deep. Mounts to a 4" (101.6 mm) square x 2.125" (53.975 mm) deep box.

Accessories: 5MB500 Etectricat Box; CB500 Barrier

Specifications for FRM·1 (A) Normal operating voltage: 15 to 32 VDC.

Maximum current draw: 6.5 rnA (lED on).

Average operating current: 230 ~A direct poll; 255 ~A group poll.

EOl resistance: not used.

Temperature range: 32'F to 120'F (O'C to 49' C).

Humidity range: 10% to 93% non-condensing.

Dimensions: 4.5' (114.3 mm) high x 4' (101.6 mm) wide x 1.25" (31 .75 mm) deep. Mounts to a 4' (101.6 mm) square x 2.125' (53.975 mm) deep box.

Accessories: 5MB500 Electrical Box; CB500 Barrier

Agency Listings and Approvals In some cases, certain modules may not be listed bY cerlain approval agencies, or listing may be In process. ConsuH lac· tory lor latest listing status.

" Ul: S635 " UlC: S3705 (A varsion only) " FM Approved " CSFM: 7300·0028:0219 • MEA: 14·00·E

" FDNY: COA #6067, #6065

Contact Ratings for FRM.1(A)

Current Maximum load Application Rating Voltage Description

3A 30VDC Resistive Non·Coded

2A 30VDC Resistive Coded

.9A 110 VDC Resistive Non..Coded

.9A 125VDC Reslsllve Non..Coded

.5A 30VDC Inductive Coded (UR=5ms)

1 A 30VDC Inductive Coded (UR=2ms)

.3A 125VAC Inductive Non·Coded (PF=0.35)

Inductive 1.5 A 25VAC (PF=0.35) Non-Coded

Inductive .7A 70.7VAC (PF=0.35) Non·Coded

Inductive 2A 25VAC (PF=O.35) Non·Coded

NOTE: Maximum (Speakers): 70.7 V RMS, 50 W

Product Une Information NOTE: 'A" suffix indicates ULC Listed model.

FCM·l(A): Intelligent Addressable Control Module.

FRM·l(A): Intelligent Addressable Relay Module.

A2143·20: Capacitor, required lor Class A (Style Z) operation 01 speakers.

5MB500: Optional Surface·Mount Backbox.

CBSOO: Control Module Barrier - required by UL for separat· ing power·limlted and non·power limited wiring In the same junction box as FCM·l (A).

NOTE: For installation instructions. see the following documents:

• FCM·l(A) Installation documenI156·1169.

• FRM·l(A) Installation document 156·3502 .

• NoUfier SLC Wiring Manual, document 51253.

NotHler® and flnhScan!!l are registered trademarks of Honeywell Intemational lnc. C2011 by Honeywell Inlemalianallnc. All rights reserved. Unauthorized use of this document is strictly prohibited.

110 ILtQl ThIs document Is nol intended to be used for lnslallation purposes.

c::: II ' n Til' I II I>

__ IU SSIM IIIIIIY nnl ••

We Iry to keep our product informaUon up-to-date and accurate. We caMot cover all specific app'lcations or antk:lpate aU requirements.

At1 specifications are subject to change without nolice.

For more Inlannatio", contact Notifier. Phone: (203) 484-7161 , FAX: (203) 484-7118. www.nolifier.com

Page 2 of 2 - DN·6724:B3· 211712011

Made In the U.S. A.