Notice Econokit Gas Etapes en 2

1
Econokit Gas installation process. 1. Insert the diffuser in a rubber hose in suction (vacuum hose) placed between the throttle butterfly and the engine. The usable hoses are: canister hose or crankcase breather. Definition of canister : system that allows the recovery and recycling of fuel vapors from the fuel tank. Definition of crankcase breather : vacuum hose mounted on the sump (oil pan), for discharging the lubricating oil vapors. Note : If the needle of the diffuser is too large, cut again diagonally, using a hacksaw. ATTENTION : Do not insert the diffuser on the brake booster hose. 2. Check manually, the suction, from the diffuser, by starting your engine. The aspiration must be substantial and immediate, even at idle. 3. Attach the diffuser on the vacuum hose thanks to 2 cable ties non-releasable. (Small PVC black collars). 4. Connect the two ends of the silicone hose to the reactor and crimp using the two metal rings. Note : Use a plier to crimp the metal rings supplied in the kit. 5. Attach Econokit Gas reactor on the exhaust manifold with the large metal collar clamp; away from the fresh air, it requires a temperature between 200°/400° Celsius (392°/752° Fahrenheit). Note : in case of impossibility of attachment to the exhaust manifold, attach the reactor at the beginning of the exhaust line Required temperature 200°/400° Celsius (392°/752° Fahrenheit). 6. Connect the reactor to the diffuser via a section of silicone hose. 7. Cut the silicone hose with the appropriate length. 8. Crimp the silicone hose with a metal ring on the diffuser. 9. Attach the bubbler vertically against a coolant hose (to get the heat) away from the fresh air using cable ties non- releasable. Note : you can connect several cable ties between them if needed. 10. Connect the top of the bubbler (white part) to the reactor via a section of silicone hose with the appropriate length. 11. Crimp the silicone hose with a metal ring on the top of the bubbler. 12. Connect the bottom of the bubbler (transparent part) to a section of 10 cm of silicone hose. 13. Insert the rigid hose in the silicone hose. 14. Crimp the rigid hose with the silicone hose with a metal ring. 15. Attach the rigid hose under the car using cable ties non-releasable to the muffler (or through the free points of anchors of the fuel lines). 16. Clip Econokit Gas collector on the top or on the side of the exhaust outlet tube. 17. Connect the collector of Econokit Gas to the rigid hose using a section of the silicone hose with the appropriate length. 18. Crimp the silicone hose to the rigid hose with a metal ring. 19. Crimp the silicone hose to the collector of Econokit Gas with a metal ring. ATTENTION: any section of silicone or rigid hose must not come into contact with a hot section of the engine as the exhaust line or muffler, the output of the turbo or exhaust manifold. 20. Start your engine, after a few minutes of driving, your Econokit Gas bubbler contains water that will be used in the creation of gas produced by Econokit Gas reactor. Now, thanks to Econokit Gas, you greatly reduce your polluting gas emissions and you consume less fuel daily! Econokit team thanks you and encourages you to be an eco-citizen. Ecology + Economy = Econokit

Transcript of Notice Econokit Gas Etapes en 2

  • Econokit Gas installation process. 1. Insert the diffuser in a rubber hose in suction (vacuum hose) placed between the throttle butterfly and the

    engine. The usable hoses are: canister hose or crankcase breather.

    Definition of canister: system that allows the recovery and recycling of fuel vapors from the fuel tank.

    Definition of crankcase breather: vacuum hose mounted on the sump (oil pan), for discharging the lubricating oil vapors.

    Note: If the needle of the diffuser is too large, cut again diagonally, using a hacksaw.

    ATTENTION: Do not insert the diffuser on the brake booster hose.

    2. Check manually, the suction, from the diffuser, by starting your engine. The aspiration must be substantial and

    immediate, even at idle.

    3. Attach the diffuser on the vacuum hose thanks to 2 cable ties non-releasable. (Small PVC black collars).

    4. Connect the two ends of the silicone hose to the reactor and crimp using the two metal rings.

    Note: Use a plier to crimp the metal rings supplied in the kit.

    5. Attach Econokit Gas reactor on the exhaust manifold with the large metal collar clamp; away from the fresh air, it

    requires a temperature between 200/400 Celsius (392/752 Fahrenheit).

    Note: in case of impossibility of attachment to the exhaust manifold, attach the reactor at the beginning of the exhaust line

    Required temperature 200/400 Celsius (392/752 Fahrenheit).

    6. Connect the reactor to the diffuser via a section of silicone hose.

    7. Cut the silicone hose with the appropriate length.

    8. Crimp the silicone hose with a metal ring on the diffuser.

    9. Attach the bubbler vertically against a coolant hose (to get the heat) away from the fresh air using cable ties non-

    releasable.

    Note: you can connect several cable ties between them if needed.

    10. Connect the top of the bubbler (white part) to the reactor via a section of silicone hose with the appropriate

    length.

    11. Crimp the silicone hose with a metal ring on the top of the bubbler.

    12. Connect the bottom of the bubbler (transparent part) to a section of 10 cm of silicone hose.

    13. Insert the rigid hose in the silicone hose.

    14. Crimp the rigid hose with the silicone hose with a metal ring.

    15. Attach the rigid hose under the car using cable ties non-releasable to the muffler (or through the free points of

    anchors of the fuel lines).

    16. Clip Econokit Gas collector on the top or on the side of the exhaust outlet tube.

    17. Connect the collector of Econokit Gas to the rigid hose using a section of the silicone hose with the appropriate

    length.

    18. Crimp the silicone hose to the rigid hose with a metal ring.

    19. Crimp the silicone hose to the collector of Econokit Gas with a metal ring.

    ATTENTION: any section of silicone or rigid hose must not come into contact with a hot section of the engine as the exhaust

    line or muffler, the output of the turbo or exhaust manifold.

    20. Start your engine, after a few minutes of driving, your Econokit Gas bubbler contains water that will be used in the

    creation of gas produced by Econokit Gas reactor.

    Now, thanks to Econokit Gas, you greatly reduce your polluting gas emissions and you consume less fuel daily!

    Econokit team thanks you and encourages you to be an eco-citizen. Ecology + Economy = Econokit