Nortel Metro Ethernet Routing Switch 8600 Installation — SFP, XFP, GBIC, and OADM Hardware ...

Nortel Metro Ethernet Routing Switch 8600

Installation — SFP, XFP,GBIC, and OADM HardwareComponentsRelease: 5.1Document Revision: 02.01

www.nortel.com

NN46220-301.

Nortel Metro Ethernet Routing Switch 8600Release: 5.1Publication: NN46220-301Document status: StandardDocument release date: 25 July 2008

Copyright © 2006-2008 Nortel NetworksAll Rights Reserved.

Printed in Canada, India, and the United States of AmericaLEGAL NOTICEWhile the information in this document is believed to be accurate and reliable, except as otherwise expresslyagreed to in writing NORTEL PROVIDES THIS DOCUMENT "AS IS" WITHOUT WARRANTY OR CONDITION OFANY KIND, EITHER EXPRESS OR IMPLIED. The information and/or products described in this document aresubject to change without notice.

Nortel, the Nortel logo, the Globemark, and Unified Networks are trademarks of Nortel Networks.All other trademarks are the property of their respective owners.

ATTENTION

For information about the regulatory message, read "Regulatory Information" in this guide.

For information about the software license, read "Software license" in this guide.

.

3.

ContentsRegulatory Information 7

EN 300386 statement 9European Union and European Free Trade Association (EFTA) notice 9Denan statement (Japan/Nippon only) 13National Environmental Statements of Compliance 13

Restriction on Hazardous Substances Directive Compliance Statement 13WEEE Directive Compliance Statement 14

Software license 15

New in this release 19Features 19Other changes 19

10GBASE DWDM XFP specifications 19Regulatory changes 19

Introduction 21Acronyms 21

Safety and regulatory information 23Handling, safety, and environmental guidelines 23

Electrostatic discharge prevention 24Care of fiber optic equipment 24

Fiber optic cable care 24Fiber optic connector care 25Job aid: connector cleaning tools and materials 26Cleaning single SC and FC connectors 26Cleaning duplex SC connectors 27Cleaning receptacles 27

Product safety warnings and information 28Electromagnetic interference compliance 29

Small form factor pluggable transceivers 33Selecting an SFP 33

SFPs 34Procedure job aid: SFPs and common applications 34

Nortel Metro Ethernet Routing Switch 8600Installation — SFP, XFP, GBIC, and OADM Hardware Components

NN46220-301 02.01 Standard25 July 2008

Copyright © 2006-2008 Nortel Networks

.

4

Procedure job aid: SFP models without DDI support 34Procedure job aid: SFP models with DDI support 35

Installing an SFP 37Procedure job aid: locking and extractor mechanisms 38

Removing an SFP 40

Gigabit interface converters 41Selecting a GBIC 41

Procedure job aid: GBIC models 42Installing a GBIC 42Removing a GBIC 43

10 Gigabit small form factor pluggable transceivers 45Selecting an XFP 45

Procedure job aid: XFP models 46Installing an XFP 47Removing an XFP 49

Optical multiplexers 51Multiplexing equipment 51Installing the shelf 52Installing a multiplexer 52Connecting an OADM 52

Procedure job aid: Optical add/drop multiplexers 53Connecting an OMUX 53

Procedure job aid: optical multiplexer/demultiplexer 54Removing a multiplexer 54

SFP specifications 55SFP labels 56General SFP specifications 57100BASE-FX SFP specifications 57100-Base LX SFP specifications 58100-Base BX10-U/D SFP specifications 58100-Base ZX SFP specifications 591000BASE-T SFP specifications 601000BASE-SX (LC) SFP specifications 601000BASE-SX (MT-RJ) SFP specifications 611000BASE-LX SFP specifications 621000BASE-XD CWDM SFP specifications 621000BASE-ZX CWDM SFP specifications 631000BASE-SX DDI SFP specifications 641000BASE-LX DDI SFP specifications 641000BASE-XD DDI 1310 nm SFP specifications 651000BASE-XD DDI 1550 nm SFP specifications 661000BASE-ZX DDI SFP specifications 66


NN46220-301 02.01 Standard25 July 2008


.

5

1000BASE-XD DDI CWDM SFP specifications 671000BASE-ZX DDI CWDM SFP specifications 681000Base CWDM SFP 681000BASE-BX DDI SFP specifications 691000BASE-EX DDI SFP specifications 71

GBIC specifications 73GBIC labels 73General GBIC specifications 741000BASE-T GBIC specifications 741000BASE-SX GBIC specifications 751000BASE-LX GBIC specifications 761000BASE-XD GBIC specifications 771000BASE-ZX GBIC specifications 781000BASE-EX CWDM GBIC specifications 79

XFP specifications 81XFP labels 81General XFP specifications 8210GBASE-SR XFP specifications 8210GBASE-LR/LW XFP specifications 8410GBASE-ER/EW XFP specifications 8510GBASE-ZR/ZW XFP specifications 8710GBASE DWDM XFP specifications 88

Multiplexer specifications 91


NN46220-301 02.01 Standard25 July 2008


.

6


NN46220-301 02.01 Standard25 July 2008


.

7.

Regulatory InformationRead the information in this section to learn about regulatory conformitiesand compliances.

International regulatory statements of conformityThis is to certify that the Nortel Networks 8000 Series chassis andcomponents installed within the chassis were evaluated to the internationalregulatory standards for electromagnetic compliance (EMC) and safety andwere found to have met the requirements for the following internationalstandards:

• EMC - Electromagnetic Emissions – CISPR 22, Class A

• EMC - Electromagnetic Immunity – CISPR 24

• Electrical Safety – IEC 60950, with CB member national deviations

Further, the equipment has been certified as compliant with the nationalstandards as detailed below.

National electromagnetic compliance (EMC) statements ofcomplianceFCC statement (USA only)

This equipment has been tested and found to comply with the limits for aClass A digital device, pursuant to Part 15 of the Federal CommunicationsCommission (FCC) rules. These limits are designed to provide reasonableprotection against harmful interference when the equipment is operatedin a commercial environment. This equipment generates, uses, and canradiate radio frequency energy. If it is not installed and used in accordancewith the instruction manual, it may cause harmful interference to radiocommunications. Operation of this equipment in a residential area is likelyto cause harmful interference, in which case users will be required to takewhatever measures may be necessary to correct the interference at theirown expense.


NN46220-301 02.01 Standard25 July 2008


.

8 Regulatory Information

ICES statement (Canada only)Canadian Department of Communications Radio InterferenceRegulations

This digital apparatus (8000 Series chassis and installed components)does not exceed the Class A limits for radio-noise emissions fromdigital apparatus as set out in the Radio Interference Regulations of theCanadian Department of Communications.

Règlement sur le brouillage radioélectrique du ministère desCommunications

Cet appareil numérique (8000 Series chassis) respecte les limites de bruitsradioélectriques visant les appareils numériques de classe A prescritesdans le Règlement sur le brouillage radioélectrique du ministère desCommunications du Canada.

CE marking statement (Europe only)EN 55 022 statements

This is to certify that the Nortel Networks 8000 Series chassis andcomponents installed within the chassis are shielded against thegeneration of radio interference in accordance with the application ofCouncil Directive 2004/108/EC. Conformity is declared by the applicationof EN 55 022 Class A (CISPR 22).

WARNINGThis is a Class A product. In a domestic environment, thisproduct may cause radio interference, in which case, the usermay be required to take appropriate measures.

WARNINGDieses ist ein Gerät der Funkstörgrenzwertklasse A.In Wohnbereichen können bei Betrieb dieses GerätesRundfunkstörungen auftreten, in welchen Fällen der Benutzerfür entsprechende Gegenmaßnahmen verantwortlich ist.

WARNINGCeci est un produit de Classe A. Dans un environnementdomestique, ce produit risque de créer des interférencesradioélectriques, il appartiendra alors à l’utilisateur de prendreles mesures spécifiques appropriées.

EN 55 024 statementThis is to certify that the Nortel Networks 8000 Series chassis is shieldedagainst the susceptibility to radio interference in accordance with theapplication of Council Directive 2004/108/EC. Conformity is declared bythe application of EN 55 024 (CISPR 24).


NN46220-301 02.01 Standard25 July 2008


.

VCCI statement (Japan/Nippon only) 9

EN 300386 statementThe Ethernet Routing Switch 8000 Series chassis complies with therequirements of EN 300386 V1.3.3 for emissions and for immunity for aClass A device intended for use in either Telecommunications centre orlocations other than telecommunications centres given the performancecriteria as specified by the manufacturer.

EC Declaration of ConformityThis product conforms to the provisions of the R&TTE Directive1999/5/EC.

European Union and European Free Trade Association (EFTA)notice

All products labeled with the CE marking comply with R&TTE Directive(1999/5/EEC) which includes the Electromagnetic Compliance (EMC)Directive (2004/108/EC) and the Low Voltage Directive (2006/95/EC)issued by the Commission of the European Community.

Compliance with these directives implies conformity to the followingEuropean Norms (ENs). The equivalent international standards are listedin parentheses.

• EN 55022 (CISPR 22)—Electromagnetic Interference

• EN 55024 (IEC 61000-4-2, -3, -4, -5, -6, -8, -11)—ElectromagneticImmunity

• EN 61000-3-2 (IEC 610000-3-2)—Power Line Harmonics

• EN 61000-3-3 (IEC 610000-3-3)—Power Line Flicker

VCCI statement (Japan/Nippon only)This is a Class A product based on the standard of the Voluntary ControlCouncil for Interference (VCCI) for information technology equipment.If this equipment is used in a domestic environment, radio disturbancemay arise. When such trouble occurs, the user may be required to takecorrective actions.


NN46220-301 02.01 Standard25 July 2008


.


BSMI statement for 8010, 8006 and 8003 chassis (Taiwan only)This is a Class A product based on the standard of the Bureau ofStandards, Metrology and Inspection (BSMI) CNS 13438, Class A.

MIC notice for 8010, 8006, 8003 chassis (Republic of Korea only)This device has been approved for use in Business applications only perthe Class A requirements of the Republic of Korea Ministry of Informationand Communications (MIC). This device may not be sold for use in anon-business application.

National safety statements of complianceCE marking statement (Europe only)

EN 60 950 statementThis is to certify that the Nortel Networks 8000 Series chassis andcomponents installed within the chassis are in compliance with therequirements of EN 60 950 in accordance with the Low Voltage Directive.Additional national differences for all European Union countries have beenevaluated for compliance. Some components installed within the 8000Series chassis may use a nickel-metal hydride (NiMH) and/or lithium-ionbattery. The NiMH and lithium-ion batteries are long-life batteries, and it is


NN46220-301 02.01 Standard25 July 2008


.

NOM statement 8010, 8006, and 8003 chassis (Mexico only) 11

very possible that you will never need to replace them. However, shouldyou need to replace them, refer to the individual component manual fordirections on replacement and disposal of the battery.

NOM statement 8010, 8006, and 8003 chassis (Mexico only)The following information is provided on the devices described in thisdocument in compliance with the safety requirements of the Norma OficialMéxicana (NOM):

Exporter: Nortel Networks, Inc.4655 Great America ParkwaySanta Clara CA 95054 USA

Importer: Nortel Networks de México, S.A. de C.V.Avenida Insurgentes Sur #1605Piso 30, OficinaCol. San Jose InsurgentesDeleg-Benito JuarezMéxico D.F. 03900

Tel: 52 5 480 2100

Fax: 52 5 480 2199

Input: Model 8003AC:

100-240 VAC, 50-60 Hz, 9 A max. per power supply

Model 8004AC:

100-240 VAC, 50 to 60 Hz, 12-6 A max. per power supply

single supply, single supply + one redundant supply, two supplies,or two + one redundant supply configuration

Model 8005AC:

100 to 120 VAC, 50 to 60 Hz, 16 A max. per power supply

200 to 240 VAC, 50 to 60 Hz, 9.5 A max. per power supply


Model 8004DC:

-48 VDC, 29 A



NN46220-301 02.01 Standard25 July 2008


.


Model 8005DC:

-48 VDC, 42 A


Información NOM (unicamente para México)La información siguiente se proporciona en el dispositivo o en losdispositivos descritos en este documento, en cumplimiento con losrequisitos de la Norma Oficial Méxicana (NOM):

Exportador: Nortel Networks, Inc.4655 Great America ParkwaySanta Clara, CA 95054 USA

Importador: Nortel Networks de México, S.A. de C.V.Avenida Insurgentes Sur #1605Piso 30, OficinaCol. San Jose InsurgentesDeleg-Benito JuarezMéxico D.F. 03900

Tel: 52 5 480 2100

Fax: 52 5 480 2199

Embarcar a: Model 8003AC:

100-240 VCA, 50-60 Hz, 9 A max. por fuente de poder

Model 8004AC:

100-240 VCA, 50 - 60 Hz, 12-6 A max. por fuente de poder

una fuente, una fuente + configuraciones de una fuente redundante,dos fuentes o dos + configuraciones de una fuente redundante

Model 8005AC:

100 - 120 VCA, 50 -60 Hz, 16 A max. por fuente de poder

200 - 240 VCA, 50 - 60 Hz, 9.5 A max. por fuente de poder


Model 8004DC:


NN46220-301 02.01 Standard25 July 2008


.

National Environmental Statements of Compliance 13

-48 VCD, 29 A


Model 8005DC:

-48 VCD, 42 A

una fuente, una fuente + configuraciones de una fuenteredundante, dos fuentes o dos + configuraciones de una fuenteredundante

Denan statement (Japan/Nippon only)

National Environmental Statements of ComplianceThe WEEE Directive 2002/96/EC and RoHS (Restriction of HazardousSubstances) Directive 2002/95/EC sets collection, recycling and recoverytargets for various categories of electrical products and their waste.

Restriction on Hazardous Substances Directive Compliance StatementThe Restriction on Hazardous Substances Directive (RoHS) (2002/95/EC),which accompanies the WEEE Directive, bans the use of heavy metalsand brominated flame-retardants in the manufacture of electrical andelectronic equipment. Specifically, restricted materials under the RoHSDirective are Lead (including solder used in PCB’s), Cadmium, Mercury,Hexavalent Chromium, and Bromine.

Nortel declares compliance with the European Union (EU) RoHS Directive(2002/95/EC) in that Lead, which is a restricted hazardous substance,is used only in accordance to the exemption(s) to Article 4(1), item 7granted by the European Union (EU) RoHS Directive (2002/95/EC) inthe Annex—"lead in solders for network infrastructure equipment forswitching, signalling, transmission as well as network management fortelecommunication".


NN46220-301 02.01 Standard25 July 2008


.


WEEE Directive Compliance Statement

This product at end of life is subject to separate collection and treatment in theEU Member States, Norway, and Switzerland and therefore is marked with thesymbol shown at the left. Treatment applied at end of life of these products inthese countries shall comply with the applicable national laws implementingDirective 2002/96/EC on Waste of Electrical and Electronic Equipment (WEEE).

Nortel declares compliance with the European Union (EU) WEEE Directive(2002/96/EC).


NN46220-301 02.01 Standard25 July 2008


.

15.

Software licenseThis section contains the Nortel Networks software license.

Nortel Networks Inc. software license agreementThis Software License Agreement ("License Agreement") is betweenyou, the end-user ("Customer") and Nortel Networks Corporation andits subsidiaries and affiliates ("Nortel Networks"). PLEASE READ THEFOLLOWING CAREFULLY. YOU MUST ACCEPT THESE LICENSETERMS IN ORDER TO DOWNLOAD AND/OR USE THE SOFTWARE.USE OF THE SOFTWARE CONSTITUTES YOUR ACCEPTANCE OFTHIS LICENSE AGREEMENT. If you do not accept these terms andconditions, return the Software, unused and in the original shippingcontainer, within 30 days of purchase to obtain a credit for the fullpurchase price.

"Software" is owned or licensed by Nortel Networks, its parent or one ofits subsidiaries or affiliates, and is copyrighted and licensed, not sold.Software consists of machine-readable instructions, its components, data,audio-visual content (such as images, text, recordings or pictures) andrelated licensed materials including all whole or partial copies. NortelNetworks grants you a license to use the Software only in the countrywhere you acquired the Software. You obtain no rights other than thosegranted to you under this License Agreement. You are responsible for theselection of the Software and for the installation of, use of, and resultsobtained from the Software.

1. Licensed Use of Software. Nortel Networks grants Customer anonexclusive license to use a copy of the Software on only one machineat any one time or to the extent of the activation or authorized usage level,whichever is applicable. To the extent Software is furnished for use withdesignated hardware or Customer furnished equipment ("CFE"), Customeris granted a nonexclusive license to use Software only on such hardwareor CFE, as applicable. Software contains trade secrets and Customeragrees to treat Software as confidential information using the same careand discretion Customer uses with its own similar information that it doesnot wish to disclose, publish or disseminate. Customer will ensure thatanyone who uses the Software does so only in compliance with the terms


NN46220-301 02.01 Standard25 July 2008


.

16 Software license

of this Agreement. Customer shall not a) use, copy, modify, transferor distribute the Software except as expressly authorized; b) reverseassemble, reverse compile, reverse engineer or otherwise translate theSoftware; c) create derivative works or modifications unless expresslyauthorized; or d) sublicense, rent or lease the Software. Licensors ofintellectual property to Nortel Networks are beneficiaries of this provision.Upon termination or breach of the license by Customer or in the eventdesignated hardware or CFE is no longer in use, Customer will promptlyreturn the Software to Nortel Networks or certify its destruction. NortelNetworks may audit by remote polling or other reasonable means todetermine Customer’s Software activation or usage levels. If suppliers ofthird party software included in Software require Nortel Networks to includeadditional or different terms, Customer agrees to abide by such termsprovided by Nortel Networks with respect to such third party software.

2. Warranty. Except as may be otherwise expressly agreed to inwriting between Nortel Networks and Customer, Software is provided"AS IS" without any warranties (conditions) of any kind. NORTELNETWORKS DISCLAIMS ALL WARRANTIES (CONDITIONS) FOR THESOFTWARE, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY ANDFITNESS FOR A PARTICULAR PURPOSE AND ANY WARRANTY OFNON-INFRINGEMENT. Nortel Networks is not obligated to provide supportof any kind for the Software. Some jurisdictions do not allow exclusionof implied warranties, and, in such event, the above exclusions may notapply.

3. Limitation of Remedies. IN NO EVENT SHALL NORTELNETWORKS OR ITS AGENTS OR SUPPLIERS BE LIABLE FOR ANYOF THE FOLLOWING: a) DAMAGES BASED ON ANY THIRD PARTYCLAIM; b) LOSS OF, OR DAMAGE TO, CUSTOMER’S RECORDS,FILES OR DATA; OR c) DIRECT, INDIRECT, SPECIAL, INCIDENTAL,PUNITIVE, OR CONSEQUENTIAL DAMAGES (INCLUDING LOSTPROFITS OR SAVINGS), WHETHER IN CONTRACT, TORT OROTHERWISE (INCLUDING NEGLIGENCE) ARISING OUT OFYOUR USE OF THE SOFTWARE, EVEN IF NORTEL NETWORKS,ITS AGENTS OR SUPPLIERS HAVE BEEN ADVISED OF THEIRPOSSIBILITY. The forgoing limitations of remedies also apply to anydeveloper and/or supplier of the Software. Such developer and/or supplieris an intended beneficiary of this Section. Some jurisdictions do not allowthese limitations or exclusions and, in such event, they may not apply.

4. General

1. If Customer is the United States Government, the following paragraphshall apply: All Nortel Networks Software available under this LicenseAgreement is commercial computer software and commercial computer


NN46220-301 02.01 Standard25 July 2008


.

Nortel Networks Inc. software license agreement 17

software documentation and, in the event Software is licensed foror on behalf of the United States Government, the respective rightsto the software and software documentation are governed by NortelNetworks standard commercial license in accordance with U.S. FederalRegulations at 48 C.F.R. Sections 12.212 (for non-DoD entities) and48 C.F.R. 227.7202 (for DoD entities).

2. Customer may terminate the license at any time. Nortel Networksmay terminate the license if Customer fails to comply with the termsand conditions of this license. In either event, upon termination,Customer must either return the Software to Nortel Networks or certifyits destruction.

3. Customer is responsible for payment of any taxes, including personalproperty taxes, resulting from Customer’s use of the Software.Customer agrees to comply with all applicable laws including allapplicable export and import laws and regulations.

4. Neither party may bring an action, regardless of form, more than twoyears after the cause of the action arose.

5. The terms and conditions of this License Agreement form the completeand exclusive agreement between Customer and Nortel Networks.

6. This License Agreement is governed by the laws of the country inwhich Customer acquires the Software. If the Software is acquired inthe United States, then this License Agreement is governed by thelaws of the state of New York.


NN46220-301 02.01 Standard25 July 2008


.

18 Software license


NN46220-301 02.01 Standard25 July 2008


.

19.

New in this releaseThe following sections describe what’s new in Nortel Metro EthernetRouting Switch 8600 Installation — SFP, XFP, GBIC , and OADMHardware Components, NN46220-301 for Release 5.1.

• “Features” (page 19)

• “Other changes” (page 19)

FeaturesThere are no new features in this document.

Other changesThis section describes the changes that are not feature-related.

• “10GBASE DWDM XFP specifications” (page 19)

• “Regulatory changes” (page 19)

10GBASE DWDM XFP specificationsThe following additions were made to the 10GBASE DWDM XFPspecifications section.

• DWDM XFP wavelengths table. For more information, see Table 44"DWDM XFP wavelengths" (page 89).

• Cautionary note about equipment damage. For more information, see“10GBASE DWDM XFP specifications” (page 88).

• Polarization Mode Dispersion to the receiver characteristics sectionin the 10GBASE DWDM OC-192 XFP specifications table. Formore information, see Table 43 "10GBASE DWDM OC-192 XFPspecifications" (page 88).

Regulatory changesA regulatory information chapter was added.


NN46220-301 02.01 Standard25 July 2008


.

20 New in this release


NN46220-301 02.01 Standard25 July 2008


.

21.

IntroductionThis document provides installation instructions and technicalspecifications for:

• Small Form Factor Pluggable (SFP) transceivers

• Gigabit Interface Converters (GBIC)

• 10 Gigabit Small Form Factor Pluggable (XFP) transceivers

• Optical multiplexers

For a list of supported SFPs, GIBCs, and XFPs see your latestproduct-specific release notes. Information contained in the Release Notestakes precedence over any information contained in this document.

AcronymsThe following table defines acronyms used in this document.

Table 1Acronyms

CDR clock data recovery

CWDM coarse wavelength-division multiplexing

DMD differential mode delay

DWDM dense wavelength-division multiplexing

EMI electromagnetic interference

ESD electrostatic discharge

GBIC Gigabit Interface Converters

LC latch connector

LED light emitting diode

MAN metropolitan area network

MMF multimode fiber

OMA Optical Modulation Amplitude

OMUX Optical Multiplexer/Demultiplexer


NN46220-301 02.01 Standard25 July 2008


.

22 Introduction

Table 1Acronyms (cont’d.)

RJ registered jack

SC snap-in connector

SFP small form factor pluggable

SMF single mode fiber

TPE Twisted Pair Ethernet

UTP unshielded twisted pair

WAN wide area network

WDM wavelength-division multiplexing

XFP 10 Gigabit Ethernet small form factor pluggable


NN46220-301 02.01 Standard25 July 2008


.

23.

Safety and regulatory informationThis section contains important safety and regulatory information. Readthis section before you install Small Form Factor Pluggable (SFP)transceivers, 10 Gigabit SFP (XFP) transceivers, or GigaBit InterfaceConverters (GBIC).

Navigation• “Handling, safety, and environmental guidelines” (page 23)

• “Care of fiber optic equipment” (page 24)

• “Product safety warnings and information” (page 28)

• “Electromagnetic interference compliance” (page 29)

Handling, safety, and environmental guidelinesBefore you install a GBIC, SFP, or XFP, read the following handling,safety, and environmental guidelines:

• GBICs, SFPs, and XFPs are static sensitive. To prevent damage fromelectrostatic discharge (ESD), see “Electrostatic discharge prevention”(page 24).

• GBICs, SFPs, and XFPs are dust sensitive. When you store a GBIC,SFP, or XFP, or when you disconnect it from a fiber optic cable, alwayskeep a dust cover over the GBIC, SFP, or XFP optical bore.

• To clean contaminants from the optical bores of a GBIC, SFP, or XFP,use an alcohol swab or equivalent to clean the ferrules of the opticalconnector.

• Dispose of this product according to all national laws and regulations.


NN46220-301 02.01 Standard25 July 2008


.

24 Safety and regulatory information

Electrostatic discharge preventionTo prevent equipment damage, observe the following electrostaticdischarge (ESD) precautions when handling or installing the components.

• Ground yourself and the equipment to an earth or building ground. Usea grounded workbench mat (or foam that dissipates static charge) anda grounding wrist strap. The wrist strap should touch the skin and begrounded through a one megaohm resistor.

• Do not touch anyone who is not grounded.

• Leave all components in their ESD-safe packaging until installation,and use only a static-shielding bag for all storage, transport, andhandling.

• Clear the area of synthetic materials such as polyester, plastic, vinyl, orstyrofoam because these materials carry static electricity that damagesthe equipment.

Care of fiber optic equipmentFiber optic equipment must be kept clean and damage-free. Use theinformation in this section to properly maintain and care for fiber opticequipment.

Care of fiber optic equipment navigation

• “Fiber optic cable care” (page 24)

• “Fiber optic connector care” (page 25)

• “Job aid: connector cleaning tools and materials” (page 26)

• “Cleaning single SC and FC connectors” (page 26)

• “Cleaning duplex SC connectors” (page 27)

• “Cleaning receptacles” (page 27)

Fiber optic cable careAlthough the glass fiber of fiber optic cable is protected with reinforcingmaterial and plastic insulation, it is subject to damage. Use the followingprecautions to avoid damaging the glass fiber.

• Do not kink, knot, or vigorously flex the cable.

• Do not bend the cable to less than a 40 mm radius.

• Do not stand on fiber optic cable; keep the cable off the floor.

• Do not pull fiber optic cable any harder than you would a cablecontaining copper wire of comparable size.


NN46220-301 02.01 Standard25 July 2008


.

Care of fiber optic equipment 25

• Do not allow a static load of more than a few pounds on any sectionof the cable.

• Place protective caps on fiber optic connectors that are not in use.

• Store unused fiber optic patch cables in a cabinet, on a cable rack, orflat on a shelf.

Frequent overstressing of fiber optic cable causes progressivedegeneration that leads to failure.

If you suspect damage to a fiber optic cable, either due to mishandlingor an abnormally high error rate observed in one direction, reverse thecable pairs. If the high error rate appears in the other direction, replacethe cable.

CAUTIONRick of equipment damageDo not crush fiber optic cable. If fiber optic cable is in thesame tray or duct with large, heavy electrical cables, it can bedamaged by the weight of the electrical cable.

Fiber optic connector careBefore connecting them to transmission equipment, test equipment,patch panels, or other connectors, clean all fiber optic connectors. Theperformance of an optical fiber connector depends on how clean theconnector and coupling are at the time of connection. Use the followingcleaning procedures when analyzing fiber connector integrity.

If a connector performs poorly after cleaning, visually inspect the connectorto determine the possible cause of the problem and to determine if it needsreplacing.

WARNINGRisk of eye injuryDo not look into the end of fiber optic cable. The light sourceused in fiber optic cables can damage your eyes.

To avoid getting debris in your eyes, wear safety glasses whenworking with the canned air duster.

To avoid eye irritation on contact, wear safety glasses whenworking with isopropyl alcohol.

Perform the following maintenance procedures to ensure that optical fiberassemblies function properly. To prevent them from collecting dust, makesure connectors are covered when not in use.


NN46220-301 02.01 Standard25 July 2008


.


CAUTIONRisk of equipment damageTo prevent further contamination, clean fiber optic equipmentonly when there is evidence of contamination.

To prevent contamination, make sure the optical ports of allactive devices are covered with a dust cap or optical connector.

To avoid the transfer of oil or other contaminants from yourfingers to the end face of the ferrule, handle connectors withcare.

Job aid: connector cleaning tools and materialsYou need the following tools and materials to clean fiber optic connectors.

• Lint-free, nonabrasive wiping cloths

• Cotton swabs, with a tightly wrapped and talcum-free tip

• Optical-grade isopropyl alcohol (IPA)

• Canned compressed air with extension tube

CAUTIONRisk of equipment damageTo avoid contamination, optical ports should only becleaned when there is evidence of contamination or reducedperformance, or during their initial installation.

To prevent oil contamination of connectors, do not usecommercial compressed air or house compressed air in place ofcanned compressed air.

Do not allow the air extension tube to touch the bottom of theoptical port.

Cleaning single SC and FC connectorsClean connectors so that the optical signal is minimally attenuated by theconnector.

Procedure steps

Step Action

1 Remove dust or debris by applying canned air to the cylindricaland end-face surfaces of the connector.

2 Gently wipe the cylindrical and end-face surfaces with a pad or awipe dampened with optical-grade isopropyl alcohol.

3 Gently wipe the cylindrical and end-face surfaces with a dry,lint-free tissue.


NN46220-301 02.01 Standard25 July 2008


.

Care of fiber optic equipment 27

4 Dry the connector surfaces by applying canned air or lettingthem air dry.

To prevent contamination, do not touch the connector surfacesafter cleaning; and cover them with dust caps if you are notgoing to use them right away.

--End--

Cleaning duplex SC connectorsClean connectors so that the optical signal is minimally attenuated by theconnector.

Procedure steps

Step Action

1 To remove or retract the shroud, do one of the following.

• On removable shroud connectors, hold the shroud on the topand bottom at the letter designation, apply medium pressure,and pull it free from the connector body. Do not discard theshroud.

• On retractable shroud connectors, hold the shroud in itsretracted position.

2 Remove dust or debris from the ferrules and connector face withthe canned air duster.

3 Gently wipe the cylindrical and end-face surfaces of both ferrulesusing a wipe saturated with optical-grade isopropyl alcohol.

4 Gently wipe the cylindrical and end-face surfaces of theconnector with Texwipe cloth (or dry lint-free tissue).

5 Blow dry the connector surfaces with canned air.

6 Using care to not touch the clean ferrules, gently push theshroud back onto the connector until it seats and locks in place.

--End--

Cleaning receptaclesClean connector receptacles or ports so that the optical signal is minimallyattenuated by the connection.


NN46220-301 02.01 Standard25 July 2008


.


Procedure steps

Step Action

1 Remove dust or debris by blowing canned air into the optical portof the device using the canned air extension tube.

2 Clean the optical port by inserting a small dry swab into thereceptacle and rotating it.

Each cleaning wand should only be used to clean one opticalport.

3 Reconnect the optical connector and check for proper function.

If problems persist, ensure that the connector and receptacle arenot damaged.

--End--

Product safety warnings and informationThe products described in this guide meet requirements of:

IEC 60950 3rd editionCSA 22.2 No. 60950 3rd editionUL 60950 3rd editionEN60950 3rd editionEN60825-1, +A11, +A2

WARNINGRisk of eye injuryFiber optic equipment can emit laser or infrared light that caninjure your eyes. Never look into an optical fiber or connectorport. Always assume that fiber optic cables are connected to alight source.

ATTENTIONVorsicht:Glasfaserkomponenten können Laserlicht bzw. Infrarotlicht abstrahlen,wodurch Ihre Augen geschädigt werden können. Schauen Sie niemals in einenGlasfaser-LWL oder ein Anschluβteil. Gehen Sie stets davon aus, daβ dasGlasfaserkabel an eine Lichtquelle angeschlossen ist.


NN46220-301 02.01 Standard25 July 2008


.

Electromagnetic interference compliance 29

ATTENTIONAvertissement:L’équipement à fibre optique peut émettre des rayons laser ou infrarouges quirisquent d’entraîner des lesions oculaires. Ne jamais regarder dans le port d’unconnecteur ou d’un câble à fibre optique. Toujours supposer que les câbles àfibre optique sont raccordés à une source lumineuse.

ATTENTIONAdvertencia:Los equipos de fibra óptica pueden emitir radiaciones de láser o infrarrojas quepueden dañar los ojos. No mire nunca en el interior de una fibra óptica ni deun puerto de conexión. Suponga siempre que los cables de fibra óptica estánconectados a una fuente luminosa.

ATTENTIONAvvertenza:Le apparecchiature a fibre ottiche emettono raggi laser o infrarossi che possonorisultare dannosi per gli occhi. Non guardare mai direttamente le fibre otticheo le porte di collegamento. Tenere in considerazione il fatto che i cavi a fibreottiche sono collegati a una sorgente luminosa.

CAUTIONRisk of equipment damageOnly qualified technicians should install this equipment.

Place all printed circuit boards on an antistatic mat until you areready to install them. If you do not have an antistatic mat, weara discharge leash to free yourself of static before touching anyof the printed circuit boards, or free yourself of static by touchinga grounded metal object before you handle a printed circuitboard.

Electromagnetic interference complianceWARNINGRisk of electromagnetic radiation exposureUse of controls or adjustments, or performance of proceduresother than those specified herein can result in hazardousradiation exposure.

The products described in this guide meet requirements of:


NN46220-301 02.01 Standard25 July 2008


.


FCC Part 15, Subparts A and B, Class AEN55022: 1998/CISPR22:1997), Class AGeneral License VDE 0871, Class B(AmtsblVfg No. 243/1991, Vfg 46/1992) VCCI Class A ITEEN55024:1998/CISPR24:1997

Federal Communications Commission (FCC) Compliance Notice: RadioFrequency Notice

This equipment has been tested and found to comply with the limits for aClass A digital device, pursuant to Part 15 of the FCC rules. These limitsare designed to provide reasonable protection against harmful interferencewhen the equipment is operated in a commercial environment. Thisequipment generates, uses, and can radiate radio frequency energy. Ifit is not installed and used in accordance with the instruction manual, itmay cause harmful interference to radio communications. Operation ofthis equipment in a residential area is likely to cause harmful interference,in which case users will be required to take whatever measures may benecessary to correct the interference at their own expense.

European EN 55 022 statementThis is to certify that the Nortel Networks optical routing system is shieldedagainst the generation of radio interference in accordance with theapplication of Council Directive 89/336/EEC, Article 4a. Conformity isdeclared by the application of EN 55 022 Class A (CISPR 22).

CAUTIONRisk of radio interferenceThis is a Class A product. In a domestic environment, thisproduct may cause radio interference, in which case, the usermay be required to take appropriate measures.

ATTENTIONAchtung:Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen könnenbei Betrieb dieses Gerätes Rundfunkstörungen auftreten, in welchen Fällen derBenutzer für entsprechende Gegenmaβnahmen verantwortlich ist.

ATTENTIONCeci est un produit de Classe A. Dans un environnement domestique, ceproduit risque de créer des interférences radioélectriques, il appartiendra alors àl’utilisateur de prendre les mesures spécifiques appropriées.

European EC Declaration of ConformityThese product conforms to the provisions of the R&TTE Directive1999/5/EC.


NN46220-301 02.01 Standard25 July 2008


.

Electromagnetic interference compliance 31

Japan/Nippon Voluntary Control Council for Interference (VCCI)statement

Taiwan Bureau of Standards, Metrology and Inspection (BSMI)Statement

Canadian Department of Communications Radio InterferenceRegulations

This digital apparatus does not exceed the Class A limits for radio-noiseemissions from digital apparatus as set out in the Radio InterferenceRegulations of the Canadian Department of Communications.


Cet appareil numérique respecte les limites de bruits radioélectriquesvisant les appareils numériques de classe A prescrites dans le Règlementsur le brouillage radioélectrique du ministère des Communications duCanada.

Canadian Department of Communications Radio InterferenceRegulations

This digital apparatus does not exceed the Class B limits for radio-noiseemissions from digital apparatus as set out in the Radio InterferenceRegulations of the Canadian Department of Communications.


Cet appareil numérique respecte les limites de bruits radioélectriquesvisant les appareils numériques de classe B prescrites dans le Règlementsur le brouillage radioélectrique du ministère des Communications duCanada.


NN46220-301 02.01 Standard25 July 2008


.



NN46220-301 02.01 Standard25 July 2008


.

33.

Small form factor pluggabletransceivers

This section describes how to select and install small form factor pluggable(SFP) transceivers.

Use an SFP to interface a device motherboard to a fiber optic orunshielded twisted pair network cable. The SFPs described in this sectionprovide Ethernet at 1 gigabit per second (Gbit/s).

Navigation• “Selecting an SFP” (page 33)

• “Installing an SFP” (page 37)

• “Removing an SFP” (page 40)

• “SFP specifications” (page 55)

Selecting an SFPUse an SFP transceiver to interface a device motherboard to a fiberoptic or unshielded twisted pair network cable. Select the appropriatetransceiver to provide the required reach.

Procedure steps

Step Action

1 Determine the required reach.

Depending on the product, SFPs are available for cabledistances of up to 100 meters (m), 550 m, 10 kilometers (km), 40km, 70 km, and 120 km.

2 Determine the required media and connector type.

Fiber optic cable is required for any reach over 100 m.

Possible media include CAT5, single mode fiber, and multimodefiber. Possible connectors include LC, MT-RJ, and RJ-45.


NN46220-301 02.01 Standard25 July 2008


.

34 Small form factor pluggable transceivers

3 If the media is optical fiber, determine any wavelengthrestrictions or requirements.

To expand available bandwidth on a common optical fiber, useCWDM SFPs.

4 Determine if digital diagnostic monitoring (DDM) is required.

Not all SFPs or products support DDM.

5 Use the following job aids to determine the appropriate SFP foryour application.

--End--

SFPsProcedure job aid: SFPs and common applications

The following table describes the reach provided by various SFPs. Thistable is informational only—not all Nortel ethernet switching and routingproducts support all the SFPs listed here.

Table 2SFPs and common applications

SFP model Common application

1000BASE-T Lowest-cost Gigabit Ethernet solution. Up to 100 m reach over Category 5(CAT5) unshielded twisted pair (UTP).

1000BASE-SX Well-suited for campus local area networks (LAN) and intrabuilding links.Up to 275 or 550 m reach (fiber-dependent) over a fiber pair.

1000BASE-LX Up to 10 km reach over a single mode fiber (SMF) pair. Up to 550 m reachover a multimode fiber (MMF) pair.

1000BASE-XD Up to 40 km reach over a single mode fiber pair.

1000BASE-ZX Up to 70 km reach over a single mode fiber pair.

1000BASE-BX Up to 10 km or 40 km reach. Bidirectional over one single mode fiber.

1000BASE-EX Up to 120 km reach over a single mode fiber pair.

Procedure job aid: SFP models without DDI supportSFPs are hot-swappable input/output enhancement components designedfor use with Nortel products to allow Gigabit Ethernet ports to link withother Gigabit Ethernet ports over various media types.

The SFPs described in this section do not have Digital Diagnostic Interfacecapability, and are RoHS -E5 compliant.

CWDM SFPS are also supported. CWDM technology consolidatesmultiple optical channels on a common optical fiber. CWDM uses multiplewavelengths to expand available bandwidth.


NN46220-301 02.01 Standard25 July 2008


.

Selecting an SFP 35

CWDM SFPs are designed to support high speed data communicationsfor Metropolitan Area Networks (MANs). The system uses a grid of eightCWDM optical wavelengths in both ring and point-to-point configurations.All components are color-coded by wavelength.

ATTENTIONThe attainable cable length can vary depending on the quality of the fiber opticcable used.

Table 3SFP models without DDI support

Model and connector Product number Description

1000BASE-SX (LC) AA1419013-E5 850 nm, up to 275 or 550 m

1000BASE-SX (MT-RJ) AA1419014-E5 850 nm, up to 275 or 550 m

1000BASE-LX (LC) AA1419015-E5 1310 nm, up to 10 km

1000BASE-XD CWDM (LC)(see Note 1)

AA1419025-E5 toAA1419032-E5

1470 nm to 1610 nm, up to 40 km

1000BASE-ZX CWDM (LC)(see Note 2)

AA1419033-E5 toAA1419040-E5

1470 nm to 1610 nm, up to 70 km

Note 1: Use the E6 version (AA1419053-E6 to AA1419060-E6). See Table 4 "SFP models withDDI capability" (page 36). The E6 version addresses a latching issue with the E5 version.Note 2: Use the E6 version (AA1419061-E6 to AA1419068-E6). See Table 4 "SFP models withDDI capability" (page 36). The E6 version addresses a latching issue with the E5 version.

For specifications for these SFPs, see “SFP specifications” (page 55).

Procedure job aid: SFP models with DDI supportDigital Diagnostic Monitoring (DDM) allows the Metro Ethernet RoutingSwitch 8600 to monitor SFP laser operating characteristics. MetroEthernet Routing Switch 8600 support for Digital Diagnostic Interfaces(DDI—an interface that supports DDM) involves data collection and alarmand warning monitoring. Static data collection includes the SFP vendorinformation, DDI support information, and DDI alarm and warning thresholdvalues. Dynamic data collection includes temperature, supply voltage,laser bias current, transmit power, and receive power. DDM works at anytime during active laser operation without affecting data traffic.

The warning and alarm status bits are only checked during initializationand during requests for dynamic data. If an alarm or warning is assertedor cleared, a message is logged and a trap is generated. DDM warningand alarm messages are mapped into WARNING and FATAL messagecategories for system logging purposes. If an alarm or warning isgenerated, the software does not automatically shut down the port.


NN46220-301 02.01 Standard25 July 2008


.


CWDM SFPs are also supported. CWDM SFPs are designed to supporthigh-speed data communications. A CWDM system uses a grid ofwavelengths to provide multiple channels for both ring and point-to-pointconfigurations. All components are color-coded by wavelength.

Any DDM SFP can be used in any Metro Ethernet Services Unit 1800 or1850 device or Metro Ethernet Routing Switch 8600 module that supportsSFPs. The optical functions of the SFP are supported. Access to the DDIinformation is only provided for:

• Metro ESU 1850

• Metro Ethernet Routing Switch 8600 modules 8630 and 8683

Access to DDI information is not supported for:

• Metro ESU 1800

• Metro Ethernet Routing Switch 8600 module 8668

The SFPs described in this section are all RoHS -E6 compliant.

For information about configuring DDM, see Nortel Metro Ethernet RoutingSwitch 8600 Troubleshooting, NN46220-701.

The following table lists and describes the Nortel SFP models with DDIcapability. All the optical SFPs use LC connectors.

Table 4SFP models with DDI capability

Model number andconnector

Product number Description

1000BASE-T (RJ-45) AA1419043-E6 CAT5 UTP, up to 100 m. Note thatbecause the 1000BASE-T device isall electrical, there is no need for DDIsupport.

1000BASE-SX AA1419048-E6 850 nm, up to 275 or 550 m

1000BASE-LX AA1419049-E6 1310 nm, up to 10 km

1000BASE-XD AA1419050-E6 1310 nm, up to 40 km

1000BASE-XD AA1419051-E6 1550 nm, up to 40 km

1000BASE-ZX AA1419052-E6 1550 nm, up to 70 km

1000BASE-XD CWDMAA1419053-E6 toAA1419060-E6

1470 nm to 1610 nm, up to 40 km

1000BASE-ZX CWDMAA1419061-E6 toAA1419068-E6

1470 nm to 1610 nm, up to 70 km


NN46220-301 02.01 Standard25 July 2008


.

Installing an SFP 37

Table 4SFP models with DDI capability (cont’d.)

Model number andconnector

Product number Description

1000BASE CWDM NTK591LHNTK591MH

NTK591NH

NTK591PH

NTK591QH

NTK591RH

NTK591SH

NTK591TH

1470 nm, up to 120 km1490 nm, up to 120 km

1510 nm, up to 120 km

1530 nm, up to 120 km

1550 nm, up to 120 km

1570 nm, up to 120 km

1590 nm, up to 120 km

1610 nm, up to 120 km

1000BASE-BX AA1419069-E6,AA1419070-E6

Bidirectional 1310 nm and 1490 nm, upto 10 km

1000BASE-BX AA1419076-E6,AA1419077-E6

Bidirectional 1310 nm and 1490 nm, upto 40 km

1000BASE-EX AA1419071-E6 1550 nm, up to 120 km

100-Base FX AA1419074-E6 1310 nm, MMF, up to 2 km

100-Base LX AA1419081-E5 1310 nm, SMF, up to 10 km

100-Base BX10-U AA1419082-E5 1310 nm, bidirectional upstream Tx, upto 10 km

100-Base BX10-D AA1419083-E5 1530 nm, bidirectional downstream Tx,up to 10 km

100-Base ZX AA1419084-E5 1550 nm, 70 to 80 km

For specifications for these SFPs, see “SFP specifications” (page 55).

Installing an SFPInstall an SFP to provide an interface between the switch and the networkcable.

Installing an SFP takes about 3 minutes.

SFPs are installed face up in the top row and face down in the bottom rowin modules or ESUs that are equipped with two rows of SFPs.

Prerequisites

• Verify that the SFP is the correct model for your network configuration.


NN46220-301 02.01 Standard25 July 2008


.


Procedure steps

CAUTIONRisk of equipment damageSFPs are keyed to prevent incorrect insertion. If the SFP resistspressure, do not force it; turn it over, and reinsert it.

Step Action

1 Remove the SFP from its protective packaging.

2 Grasp the SFP between your thumb and forefinger.

3 As shown in the following figure, insert the device into the sloton the module.

Apply a light pressure to the device until it clicks and locks intoposition.

Figure 1Installing an SFP

4 Remove the dust cover from the optical bore and insert the fiberoptic connector.

--End--

Procedure job aid: locking and extractor mechanismsDepending on the transceiver manufacturer, your SFP transceiver canhave various types of locking/extractor mechanisms.


NN46220-301 02.01 Standard25 July 2008


.

Installing an SFP 39

The following figures shows a typical mechanisms used on SFPtransceivers; other locking/extractor mechanisms exist, although they arenot shown here. In the figure Figure 2 "SFP with bail lock and extractionmechanism" (page 39), the SFP still has the bore plug installed. Pull thebail to release the device.

Figure 2SFP with bail lock and extraction mechanism

The following figure shows the 1000BASE-SX MT-RJ SFP. Push the tabto release the device.

Figure 31000BASE-SX MT-RJ SFP extraction mechanism

The following figure shows the wrap-around latch-type extractionmechanism. To remove the device, push the collar towards the module.


NN46220-301 02.01 Standard25 July 2008


.


Figure 4Wrap-around latch-type extraction mechanism

Removing an SFPRemove an SFP to replace it or to commission it elsewhere.

Procedure steps

Step Action

1 Disconnect the network fiber cable from the SFP connector.

2 Affix dust covers over the fiber optic bore and connector.

3 Depending on your SFP model, to release the SFP, press thelocking/extractor mechanism.

Your SFP locking/extractor mechanism can be different than themodels shown.

4 Slide the SFP out of the module SFP slot.

If the SFP does not slide easily from the module slot, use agentle side-to-side rocking motion while firmly pulling the SFPfrom the slot.

5 Store the SFP in a safe place until needed.

ATTENTIONIf you discard the SFP, be sure to dispose of it according to allnational laws and regulations.

--End--


NN46220-301 02.01 Standard25 July 2008


.

41.

Gigabit interface convertersATTENTIONThe Gigabit Interface Converters, GBIC (AA1419001 to AA1419004, AA1419017to AA1419024, and AA1419041) are no longer supported

This section describes how to install and remove Gigabit InterfaceConverters (GBIC), and lists the technical specifications for the supportedGBIC models.

Navigation• “Selecting a GBIC” (page 41)

• “Installing a GBIC” (page 42)

• “Removing a GBIC” (page 43)

• “GBIC specifications” (page 73)

Selecting a GBICUse a GBIC to interface a device motherboard to a fiber optic orunshielded twisted pair network cable. Select the appropriate transceiverto provide the required reach.

Procedure steps

Step Action


GBICs are available for cable distances of up to 100 meters (m),550 m, 10 kilometers (km), 40 km, 70 km, and 120 km.

2 Determine the required media and connector type.

Fiber optic cable is required for any reach over 100 m.

Depending on the product, possible media include CAT5, singlemode fiber, and multimode fiber. Possible connectors include SC(subscriber connector) type and RJ-45.


NN46220-301 02.01 Standard25 July 2008


.

42 Gigabit interface converters

3 If the media is optical fiber, determine any wavelengthrestrictions or requirements.

To expand available bandwidth on a common optical fiber, useCoarse Wavelength Division Multiplexing (CWDM) GBICs.

4 Use the following job aids to determine the appropriate GBIC foryour application.

--End--

Procedure job aid: GBIC modelsGBICs are hot-swappable input/output enhancement componentsdesigned for use with Nortel products to allow Gigabit Ethernet ports to linkwith other Gigabit Ethernet ports over various media types. The followingtable describes supported GBICs. For specifications for these GBICs, see“GBIC specifications” (page 73).

ATTENTIONAttainable cable length can vary depending on the quality of the fiber optic cableused.

Table 5GBIC models

Model and connector Product number Description

1000BASE-T (RJ-45) AA1419041-E5 CAT5 unshielded twisted pair (UTP), up to 100m

1000BASE-SX (SC) AA1419001-E5 850 nanometers (nm), up to 275 or 550 m

1000BASE-LX (SC) AA1419002-E5 1310 nm, up to 10 km

1000BASE-XD (SC) AA1419003-E5 1550 nm, up to 50 km

1000BASE-ZX (SC) AA1419004-E5 1550 nm, up to 70 km

1000BASE-EX CWDM(SC)

AA1419017-E5 toAA1419024-E5

1470 nm to 1610 nm, up to 120 km

Installing a GBICInstall a GBIC to complete the transmission path.

Installing a GBIC takes about 3 minutes.

Prerequisites

• Verify that the GBIC is the correct model for your networkconfiguration.


NN46220-301 02.01 Standard25 July 2008


.

Removing a GBIC 43

Procedure steps

CAUTIONRisk of equipment damageGBICs are keyed to prevent incorrect insertion. If the GBICresists pressure, do not force it; turn it over, and reinsert it.

Step Action

1 Remove the GBIC from its protective packaging.

2 Grasp the GBIC between your thumb and forefinger.

3 Insert the GBIC into the slot on the front panel of the GigabitEthernet switching module.Figure 5Inserting a GBIC

4 Remove the dust cover and insert the fiber optic connector.

--End--

Removing a GBICRemove a GBIC to replace it or to commission it elsewhere.

Procedure steps

Step Action

1 Disconnect the network fiber cable from the GBIC connector.

2 Attach a dust cover over the fiber optic bore.

3 Depending on your GBIC model, grasp the extraction tabslocated on either side of the GBIC with your thumb andforefinger, or lift the extractor handle attached to the GBIC.


NN46220-301 02.01 Standard25 July 2008


.

44 Gigabit interface converters

Figure 6GBIC models

4 Slide the GBIC out of the Gigabit Ethernet module slot.

If the GBIC does not slide easily from the module slot, use agentle side-to-side rocking motion while firmly pulling the GBICfrom the slot.

5 Store the GBIC in a safe place until needed.

ATTENTIONIf you discard the GBIC, be sure to dispose of it according to allnational laws and regulations.

--End--

ATTENTIONWhen you contact a Nortel service representative for troubleshooting purposes,you must have the following information available:

• Nortel serial number

• Manufacturer’s code

• Interface type

• GBIC part number


NN46220-301 02.01 Standard25 July 2008


.

45.

10 Gigabit small form factor pluggabletransceivers

This section describes how to install and remove 10 Gigabit SmallForm Factor Pluggable (XFP) transceivers, and lists some technicalspecifications for the supported XFP models.

ATTENTIONNortel recommends that you only use Nortel qualified XFPs. If you do chooseto use other vendor XFPs, be aware that Nortel does not support the use ofother XFPs.

Navigation• “Selecting an XFP” (page 45)

• “Installing an XFP” (page 47)

• “Removing an XFP” (page 49)

Selecting an XFPUse an XFP transceivers to interface a device motherboard to a fiber opticcable. Select the appropriate transceiver to provide the required reach.

Procedure steps

Step Action


XFPs are available for cable distances of up to 300 meters (m),10 kilometers (km), 40 km, and 80 km.

2 Determine any wavelength restrictions or requirements.


NN46220-301 02.01 Standard25 July 2008


.

46 10 Gigabit small form factor pluggable transceivers

3 Use the following job aids to determine the appropriate XFP foryour application.

--End--

Procedure job aid: XFP modelsXFPs are hot-swappable input/output enhancement components designedfor use with Nortel products to allow 10 Gigabit Ethernet ports to link withother 10 Gigabit Ethernet ports. Digital diagnostic monitoring (DDM) allowsreal-time access to device operating parameters. All XFPs come with DDMcapability.

All Nortel XFPs use LC connectors to provide precision keying, lowinterface losses, and space savings.

The following table lists and describes the Nortel XFP models. Forspecifications for these XFPs, see “XFP specifications” (page 81).

ATTENTIONYou can configure the XFP to operate in either LAN or WAN mode, dependingon the module (8683XLR is a LAN-only module, and 8683XZR is a LAN/ WANmodule). Model numbers ending in R denote a LAN interface; model numbersending in W denote a WAN interface.

CAUTIONRisk of equipment damageNortel recommends that you install only one 10GBASE-ZR/ZWXFP per module due to cooling limitations on the 8683XLR and8683XZR modules. Nortel further recommends the installation ofthe XFP only in port 1. You can install a 10GBASE-SR, -LR/LW,or -ER/EW in one or both of the remaining ports.

Table 6XFP models

Model number Product number Description

10GBASE-SR AA1403005-E5 850 nanometers (nm). The range is up to:• 22 m using 62.5 micrometer (µm), 160

megaHertz times km (MHz-km) MMF

• 33 m using 62.5 µm, 200 MHz-km MMF

• 66 m using 62.5 µm, 500 MHz-km MMF

• 82 m using 50 µm, 500 MHz-km MMF

• 300 m using 50 µm, 2000 MHz-km MMF

10GBASE-LR/LW AA1403001-E5 1310 nm SMF. The range is up to 10 km.

10GBASE-ER/EW AA1403003-E5 1550 nm SMF. The range is up to 40 km.


NN46220-301 02.01 Standard25 July 2008


.

Installing an XFP 47

Table 6XFP models (cont’d.)

Model number Product number Description

10GBASE-ZR/ZW AA1403006-E5 1550 nm SMF. The range is up to 80 km.

NTK587AY-E5 1537.40

NTK587BA-E5 1538.19

NTK587BC-E5 1538.98

NTK587BE-E5 1539.77

NTK587BG-E5 1540.56

NTK587BJ-E5 1541.35

NTK587BL-E5 1542.14

NTK587BN-E5 1542.94

NTK587BQ-E5 1543.73

NTK587BS-E5 1544.53

10GBASE DWDM

NTK587BU-E5 1545.32

Note: Due to hexidecimal to decimal rounding, and vice-versa, the wavelength numbers providedby the XFP manufacturer and reported by the Metro Ethernet Routing Switch 8600 system mayvary slightly.

Installing an XFPInstall an XFP to provide a 10 Gigabit Ethernet interface between theswitch and other network devices.

Installing an XFP takes about 3 minutes.

Prerequisites

• Verify that the XFP is the correct model for your network configuration.

Procedure steps

CAUTIONRisk of equipment damageThis precaution applies only to the 8010, 8006, and 8003-Rchassis. Nortel recommends that you install only one10GBASE-ZR/ZW per module due to cooling limitations on the8683XLR and 8683XZR modules. Nortel further recommendsthe installation of the XFP only in port 1. You can install a10GBASE-SR, -LR/LW, or -ER/EW in one or both of theremaining ports.


NN46220-301 02.01 Standard25 July 2008


.


CAUTIONRisk of equipment damageXFPs are keyed to prevent incorrect insertion. If the XFP resistspressure, do not force it; turn it over, and reinsert it.

Step Action

1 Remove the XFP from its protective packaging.

2 Grasp the XFP between your thumb and forefinger.

3 Insert the XFP into the XFP slot on the module.

Apply a light pressure to the XFP until the device clicks and locksinto position in the module.Figure 7Installing an XFP

4 Remove the dust cover from the XFP optical bores and insertthe fiber optic cable.

--End--

Procedure job aid: locking and extractor mechanismsDepending on the transceiver manufacturer, your XFP transceiver canhave various types of locking/extractor mechanisms.

The following figure shows a typical bail-type mechanism used on XFPtransceivers. Pull the bail down to release the device.


NN46220-301 02.01 Standard25 July 2008


.

Removing an XFP 49

Figure 8XFP with bail lock and extraction mechanism

Removing an XFPRemove an XFP to replace it or to commission it elsewhere.

Procedure steps

Step Action

1 Disconnect the network fiber cable from the XFP connector.

2 Affix a dust cover over the optical connector.

3 Pull the bail mechanism on the XFP to release the XFP.

4 Slide the XFP out of the module XFP slot.

If the XFP does not slide easily from the module slot, use agentle side-to-side rocking motion while firmly pulling the XFPfrom the slot.

5 Replace the port dust cover or EMI plug in the module.

6 Store the XFP in a safe place until needed.

ATTENTIONIf you discard the XFP, be sure to dispose of it according to allnational laws and regulations.

--End--


NN46220-301 02.01 Standard25 July 2008


.



NN46220-301 02.01 Standard25 July 2008


.

51.

Optical multiplexersThe Nortel optical routing system supports high-speed datacommunications in metropolitan area networks (MAN) by connectingGigabit Ethernet ports with fiber optic networks, and by combining multiplewavelengths on a single fiber to expand available bandwidth.

Use multiplexers in optical routing systems to multiplex, add, or dropwavelengths in optical networks.

Multiplexing equipmentAn optical add/drop multiplexer (OADM) adds or drops one wavelength toor from a fiber carrying multiple wavelengths. An optical multiplexer addsor drops multiple wavelengths to or from a fiber.

The following table shows supported OADMs and OMUXs and thecorresponding wavelengths of operation.

Table 7CWDM multiplexers

Description CWDM OADM CWDM OMUX-4 CWDM OMUX-8

1470 nm, Gray AA1402002-E5 — AA1402010-E5

1490 nm, Violet AA1402003-E5 AA1402009-E5 AA1402010-E5

1510 nm, Blue AA1402004-E5 — AA1402010-E5

1530 nm, Green AA1402005-E5 AA1402009-E5 AA1402010-E5

1550 nm, Yellow AA1402006-E5 — AA1402010-E5

1570 nm, Orange AA1402007-E5 AA1402009-E5 AA1402010-E5

1590 nm, Red AA1402008-E5 — AA1402010-E5

1610 nm, Brown AA1402011-E5 AA1402009-E5 AA1402010-E5


NN46220-301 02.01 Standard25 July 2008


.

52 Optical multiplexers

Installing the shelfThe optical routing system (OADM/OMUX) is mounted in an optical shelfwith connections at the front of the module. For user access to theseconnections, a minimum of 36 inches (90 cm) of clearance is required.Keep the area as dust-free as possible.

Step Action

1 Support the chassis so that all the mounting holes in the opticalshelf are aligned with the corresponding holes in the rack.

2 Attach two rack mounting bolts to each side of the rack.

3 Tighten all the bolts in rotation.

--End--

Installing a multiplexerOADMs and OMUXs are passive devices that require no power for theiroperation. You can inser them in the optical shelf and then connect theminto your network.

Step Action

1 Align the plug-in module with the optical shelf.

2 Gently push the plug-in module into the shelf cavity.

3 Tighten the captive screws.

4 Connect the network cables.

--End--

Connecting an OADMUse this procedure to connect the OADM to SFP or GBICs and to eastand west backbone interfaces.

Step Action

1 Insert the GBIC or SFPs into their respective modules. Makesure that you have the correct GBIC or SFP for your networkconfiguration by matching the color of the label to the color of theconnector label on the OADM.

2 Clean all fiber optic connectors on the cabling.


NN46220-301 02.01 Standard25 July 2008


.

Connecting an OMUX 53

3 Connect the fiber optic cables from the GBIC or SFP transmit(Tx) and receive (Rx) connectors to the OADM Equipment RXand TX Equipment connectors.

4 Connect the west network backbone fiber optic cable to theOADM west connector.

5 Connect the east backbone fiber optic cable to the OADM eastconnector.

--End--

Procedure job aid: Optical add/drop multiplexersThe Nortel passive CWDM Optical Add/Drop Multiplexer (OADM) sendsand receives signals to and from CWDM GBICs and SFPs installed inthe switch. It adds or drops a specific wavelength from the optical fiber,and allows all other wavelengths to pass through unaffected. The OADMsupports tow separate fiber pathways traveling in opposite directions (eastand west) so that the network remains viable even if the fiber is broken atone point on the ring.

Connecting an OMUXUse this procedure to connect the OMUX to SFP or GBICs and to eastand west backbone interfaces.

WARNINGMultiplexing together several GICs or SFPs can produce aradiant power level in the fiber that exceeds the class 1 laserlimit. To avoid damage to yourself or to the equipment, takecare that you follow proper connector safety and cleaningprocedures.

Step Action

1 Insert the GBICs or SFPs into their respective modules.

2 Clean all fiber optic connectors.

3 Connect the fiber optic cables from the GBIC/SFP TX and RX tothe OMUX Equipment RX and TX Equipment connectors. TheGBIC or SFP wavelength must match the OMUX equipmentconnector wavelength. The TX of one device must alwaysconnect to the RX of the next device.

4 Connect the network backbone east fiber optic cables to the east(left) OMUX.


NN46220-301 02.01 Standard25 July 2008


.

54 Optical multiplexers

5 Connect the network backbone west fiber optic cables to thewest (right) OMUX.

--End--

Procedure job aid: optical multiplexer/demultiplexerThe Nortel passive optical multiplexer/demultiplexer (OMUX) sends andreceives signals to/from GBIC and SFP transceivers installed in the switch.It multiplexes and demultiplexes four or eight CWDM wavelengths from atwo-fiber (east and west) circuit. Use the OMUX to create unidirectionalnetwork traffic rings or point-to-point links.

Removing a multiplexerOADMs and OMUXs require no power for their operation. You can removethem from the optical shelf after disconnecting them from your network.

Step Action

1 Disconnect the network cabling from the multiplexer. Cover allreceptacles and connectors with dust caps.

2 Loosen the captive screws on both sides of the module.

3 to release the module, gently pull on both screws at the sametime.

4 Slide the module out of the shelf.

--End--


NN46220-301 02.01 Standard25 July 2008


.

55.

SFP specificationsThis section provides technical specifications for the supported smallform factor pluggable (SFP) models. Use this information to aid in propernetwork design.

The specifications given in this section meet or exceed those specified inthe applicable IEEE standards, where they exist.

In these specifications, unless otherwise noted, receiver sensitivity isdefined as the minimum average input optical power for which the receiveris guaranteed to meet the bit error rate (BER) of 10-12.

ATTENTIONNortel recommends that you only use Nortel-qualified SFPs. If you do chooseto use other vendor SFPs, be aware that Nortel does not support the use ofother SFPs.

Information about SFP and XFP power consumption has been added toInstallation—Modules, NN46220-306 in a section entitled "SFPs, XFPs, Rand RC modules, and power consumption".

Navigation• “SFP labels” (page 56)

• “General SFP specifications” (page 57)

• “100BASE-FX SFP specifications” (page 57)

• “100-Base LX SFP specifications” (page 58)

• “100-Base BX10-U/D SFP specifications” (page 58)

• “100-Base ZX SFP specifications” (page 59)

• “1000BASE-T SFP specifications” (page 60)

• “1000BASE-SX (LC) SFP specifications” (page 60)

• “1000BASE-SX (MT-RJ) SFP specifications” (page 61)

• “1000BASE-LX SFP specifications” (page 62)


NN46220-301 02.01 Standard25 July 2008


.

56 SFP specifications

• “1000BASE-XD CWDM SFP specifications” (page 62)

• “1000BASE-ZX CWDM SFP specifications” (page 63)

• “1000BASE-SX DDI SFP specifications” (page 64)

• “1000BASE-LX DDI SFP specifications” (page 64)

• “1000BASE-XD DDI 1310 nm SFP specifications” (page 65)

• “1000BASE-XD DDI 1550 nm SFP specifications” (page 66)

• “1000BASE-ZX DDI SFP specifications” (page 66)

• “1000BASE-XD DDI CWDM SFP specifications” (page 67)

• “1000BASE-ZX DDI CWDM SFP specifications” (page 68)

• “1000Base CWDM SFP” (page 68)

• “1000BASE-BX DDI SFP specifications” (page 69)

• “1000BASE-EX DDI SFP specifications” (page 71)

SFP labelsThe Nortel label on a typical SFP contains a Nortel serial number, a barcode, a manufacturer’s code, an interface type, and a part number.

Figure 9SFP label


NN46220-301 02.01 Standard25 July 2008


.

100BASE-FX SFP specifications 57

General SFP specificationsThe following table describes general SFP specifications.

Table 8General SFP specifications

Parameter Description

Dimensions (H x W x D) 13.4 x 8.50 x 56.4 millimeters (mm)0.53 x 0.33 x 2.22 inches (in.) unless otherwisestated

Operating temperature -40 to 80C for RoHS - E6 models0 to 60C for RoHS - E5 models

Storage temperature -40 to 85C

Maximum supply current 300 mA unless otherwise stated

Maximum power consumption 1.0 W unless otherwise stated

100BASE-FX SFP specificationsThe 100BASE-FX SFP provides 100 Mbit/s Ethernet Carrier SenseMultiple Access with Collision Detection (CSMA-CD) connectivity usingmultimode optical fiber. The part number for this model is AA1419074-E6.

The following table describes the 100BASE-FX SFP specifications.

Table 9100BASE-FX SFP specifications

Parameter Specifications

Maximum electrical power consumption 1.5 W

Connectors Duplex LC

Cabling • 62.5 µm MMF optic cable

• 50 µm MMF optic cable

Distance • Up to 2 km using 500 MHz-km MMF opticcable

Wavelength 1310 nm

Link optical power budget 10 dB

Transmitter characteristics

Maximum launch power -14 dBm

Minimum launch power -23.5 to -20 dBm

Receiver characteristics

Receiver sensitivity 33.5 dBm

Maximum input power —


NN46220-301 02.01 Standard25 July 2008


.


100-Base LX SFP specificationsThe 100BASE-LX SFP provides 100 Mbit/s Ethernet Carrier SenseMultiple Access with Collision Detection (CSMA-CD) connectivityusing single mode optical fiber. The part number for this model isAA1419081-E5.

The following table describes the 100BASE-LX SFP specifications.

Table 10100-Base LX SFP specifications




Cabling 62.5 µm SMF optic cable50 µm MMF optic cable

Distance Up to 10 km using 500 Mhz-km MMF opticcable

Wavelength 1310 nm






Receiver sensitivity -33.5 dBm


100-Base BX10-U/D SFP specificationsThe 100BASE- BX 10-U (upstream) and 100BASE-BX 10-D (downstream)bidirectional SFP provides 100 Mbit/s Ethernet Carrier Sense MultipleAccess with Collision Detection (CSMA-CD) connectivity. The part numberfor the upstream model is AA1419082-E5. The part number for thedownstream model is AA1419083-E5.

The following table describes the 100BASE BX10-U/D SFP specifications.

Table 11100-Base BX10-U/D SFP specifications





NN46220-301 02.01 Standard25 July 2008


.

100-Base ZX SFP specifications 59

Table 11100-Base BX10-U/D SFP specifications (cont’d.)


Distance Up to 10 km

Wavelength 1310 nm Tx (upstream)1530 nm Tx (downstream)




Minimum launch power 23.5 to -20 dBm


Receiver sensitivity -33.5


100-Base ZX SFP specificationsThe 100BASE-ZX SFP provides 100 Mbit/s Ethernet Carrier SenseMultiple Access with Collision Detection (CSMA-CD) connectivity. The partnumber for this model is AA1419084-E5.

The following table describes the 100BASE-ZX SFP specifications.

Table 12100-Base ZX SFP specifications





Distance 70 km to 80 km

Wavelength 1550 nm









NN46220-301 02.01 Standard25 July 2008


.


1000BASE-T SFP specificationsThe 1000BASE-T SFP provides Gigabit Ethernet connectivity using asingle eight-pin RJ-45 connector. The 1000BASE-T SFP only operatesat 1 gigabit per second (1 Gbit/s) and does not support 100BASE-T or10BASE-T interfaces. The part number for this model is AA1419043-E6.

ATTENTIONYou must disable autonegotiation before operating the 1000BASE-T SFP.By default, SFPs inserted into certain product-specific modules are set forAutonegotiation = True.

The maximum current requirement of the SFP is 375 milliamperes (mA) at5 volts (V).

The following table describes the 1000BASE-T SFP specifications.

Table 13IEEE 802.3z 1000BASE-T SFP specifications


Standards IEEE 802.3z, IEEE 802.3ab

Connectors RJ-45

Cabling CAT5E or better UTP

Distance Up to 100 m

1000BASE-SX (LC) SFP specificationsThe 1000BASE-SX SFP provides 1000BASE-SX Gigabit Ethernetconnectivity at 850 nm using multimode optical fiber (MMF). This SFPsupports full-duplex operation only. The part number for this model isAA1419013-E5.

ATTENTIONAA1419013-E5 continues to be supported. However, it is no longer orderable.Order AA1419048-E6 as a replacement.

The following table describes standards, connectors, cabling, and distancefor the 1000BASE-SX SFP.

Table 14IEEE 802.3z 1000BASE-SX (LC) SFP specifications






NN46220-301 02.01 Standard25 July 2008


.

1000BASE-SX (MT-RJ) SFP specifications 61

Table 14IEEE 802.3z 1000BASE-SX (LC) SFP specifications (cont’d.)


Distance • up to 275 m using 62.5 µm MMF optic cable

• up to 550 m using 50 µm MMF optic cable

Wavelength 850 nanometers (nm)

Link optical power budget 7.0 decibels (dB)


Launch power -10 to -4.0 decibels referenced to 1 milliwatt(dBm)


Receiver sensitivity -17 dBm

Maximum input power 0 dBm

1000BASE-SX (MT-RJ) SFP specificationsThe 1000BASE-SX (MT-RJ type) SFP provides Gigabit Ethernetconnectivity using MT-RJ multimode fiber (MMF) connectors. The followingtable describes standards, connectors, cabling, and distance for the1000BASE-SX (MT-RJ type) SFP. The part number for this model isAA1419014-E5.

Table 15IEEE 802.3z 1000BASE-SX (MT-RJ) SFP specifications


Connectors Duplex MT-RJ



Distance • up to 275 m using 62.5 µm MMF optic cable

• up to 550 m using 50 µm MMF optic cable

Wavelength 850 nm

Link optical power budget 7.0 dB


Launch power -10 to -4.0 dBm





NN46220-301 02.01 Standard25 July 2008


.


1000BASE-LX SFP specificationsThe 1000BASE-LX SFP provides 1000BASE-LX Gigabit Ethernetconnectivity at 1310 nanometers (nm) using single mode (SMF) ormultimode optical fiber (MMF). The 1000BASE-LX SFP supportsfull-duplex operation only. The part number for this model isAA1419015-E5.

ATTENTIONAA1419015-E5 continues to be supported. However, it is no longer orderable.Order AA1419049-E6 as its replacement.

The following table describes standards, connectors, cabling, and distancefor the 1000BASE-LX SFP.

Table 16IEEE 802.3z 1000BASE-LX SFP specifications



Cabling • 50 micrometer (µm) multimode fiber (MMF)

• 62.5 µm multimode fiber

• 9 µm single mode fiber (SMF)

Distance • Up to 550 meters (m) using MMF

• Up to 10 kilometers (km) using SMF

Wavelength 1310 nm



Launch power -9.5 to -3.0 dBm



Maximum input power -3.0 dBm

1000BASE-XD CWDM SFP specificationsThe 1000Base-XD SFPs provide CWDm Gigabit Ethernet connectivityusing single-mode fiber (SMF). These SFPs support full duplex operationonly. The part numbers of the 40 km models range from AA1419025-E5 toAA1419032-E5.

ATTENTIONAA1419025-E5 to AA1419032-E5 continue to be supported. However, theyare no longer orderable. Order AA1419053-E6 to AA1419060-E6 as theirreplacements.


NN46220-301 02.01 Standard25 July 2008


.

1000BASE-ZX CWDM SFP specifications 63

Table 171000BASE-XD CWDM (40 km) SFP specifications



Cabling SMF, 9 µm

Data rate 1.0 Gbit/s

Line rate (8B/10B code) 1.25 Gbit/s

Operating temperature range 0 to 60C



Launch power -4.0 to 1.0 dBm




ATTENTIONFor the 40 km CWDM SFPs, a minimum attenuation of 4 dB must be presentbetween the transmitter and receiver. To avoid receiver saturation, you mustinsert a minimum attenuation of 4 dB when you test the CWDM SFP in loopbackmode, or use short runs of fiber with no intermediate CWDM OADM or CWDMOMUX.

1000BASE-ZX CWDM SFP specificationsThe 1000Base-Zx SFPs provide CWDM Gigabit Ethernet connectivityusing single-mode fiber (SMF). These SFPs support full duplex operationonly. The part numbers of the 70 km models range from AA1419033-E5 toAA1419040-E5.

ATTENTIONFor the 70 km CWDM SFPs, a minimum attenuation of 10 dB must be presentbetween the transmitter and receiver.

ATTENTIONAA1419033-E5 to AA1419040-E5 continue to be supported. However, theyare no longer orderable. Order AA1419061-E6 to AA1419068-E6 as theirreplacements.

Table 181000BASE-ZX CWDM (70 km) SFP specifications



Cabling SMF, 9 µm


NN46220-301 02.01 Standard25 July 2008


.


Table 181000BASE-ZX CWDM (70 km) SFP specifications (cont’d.)




Operating temperature range 0 to 60C







1000BASE-SX DDI SFP specificationsThe following table describes the 1000BASE-SX DDI SFP, which has areach of up to 550 m using 50 µm multimode fiber (MMF), and of 275 musing 62.5 µm MMF. This SFP operates at 850 nm. The part number ofthis SFP is AA1419048-E6.

Table 191000BASE-SX SFP DDI (550 m) specifications


Maximum electrical power consumption 1 watt (W)

Connector Duplex LC

Cabling MMF








Maximum receiver power 0 dBm

1000BASE-LX DDI SFP specificationsThis SFP can attain a reach of up to 10 km and operates at 1310 nm. Thepart number of this SFP is AA1419049-E6.


NN46220-301 02.01 Standard25 July 2008


.

1000BASE-XD DDI 1310 nm SFP specifications 65

Table 201000BASE-LX DDI SFP specifications


Maximum electrical power consumption 1.0 watt (W)


Cabling SMF, 9 µm








Maximum receiver power -3.0 dBm

1000BASE-XD DDI 1310 nm SFP specificationsThe following table describes the 1000BASE-XD DDI SFP. This SFPoperates at 1310 nm and has a reach of up to 40 km. The part number isAA1419050-E6.

Table 211000BASE-XD DDI 1310 nm SFP specifications




Cabling SMF, 9 µm


Line rate (8B/10B) code 1.25 Gbit/s



Launch power -4.5 to 0 dBm





NN46220-301 02.01 Standard25 July 2008


.


1000BASE-XD DDI 1550 nm SFP specificationsThe following table describes the 1000BASE-XD DDI SFP. This SFPoperates at 1550 nm and has a reach of up to 40 km. The part number isAA1419051-E6.

CAUTIONRisk of equipment damageTo prevent damage to the optical receiver, ensure that at least3 dB of attenuation is present between the transmit and receiveports.

Table 221000BASE-XD DDI 1550 nm SFP specifications

Parameter Specification



Cabling SMF, 9 µm




Maximum dispersion power penalty 2 dB at 40 km






1000BASE-ZX DDI SFP specificationsThe following table describes the 1000BASE-ZX DDI SFP. This SFPoperates at 1550 nm and has a reach of up to 70 km. The part number isAA1419052-E6.


Table 231000BASE-ZX DDI 1550 nm SFP specifications




NN46220-301 02.01 Standard25 July 2008


.

1000BASE-XD DDI CWDM SFP specifications 67

Table 231000BASE-ZX DDI 1550 nm SFP specifications (cont’d.)



Cabling SMF, 9 µm






Launch power 0 to 5 dBm



Maximum receiver power -0 dBm

1000BASE-XD DDI CWDM SFP specificationsThe following table describes specifications for 1000BASE-XD CWDMSFPs numbered AA1419053-E6 to AA1419060-E6.


Table 241000BASE-XD CWDM SFP DDI (40 km) specifications




Cabling SMF, 9 µm









NN46220-301 02.01 Standard25 July 2008


.


Table 241000BASE-XD CWDM SFP DDI (40 km) specifications (cont’d.)




1000BASE-ZX DDI CWDM SFP specificationsThe following table describes specifications for CWDM SFPs numberedAA1419061-E6 to AA1419068-E6.


Table 251000BASE-ZX CWDM SFP DDI (70 km) specifications




Cabling SMF, 9 µm






Launch power 0 to 5.0 dBm




1000Base CWDM SFPThe following table describes specifications for CWDM SFPs numberedNTK591LH/MH/NH/PH/QH/RH/SH/TH.

CAUTIONRisk of equipment damageTo prevent damage to the optical receiver, ensure that at least10 dB of attenuation is present between the transmit andreceive ports.


NN46220-301 02.01 Standard25 July 2008


.

1000BASE-BX DDI SFP specifications 69

Table 261000BASE CWDM SFP




Cabling 9 µm SMF optic cable



Wavelength (nominal central) 1471 nm, 1491 nm, 1511 nm, 1531 nm, 1551nm, 1571 nm, 1591 nm, 1611 nm



Maximum launch power 5.0 dBm

Minimum launch power 1.0 dBm




1000BASE-BX DDI SFP specificationsThe 1000BASE-BX bidirectional SFPs (part numbers AA1419069-E6,AA1419070-E6, AA1419076-E6, and AA1419077-E6) provide GigabitEthernet connectivity over a single fiber.

Figure 101000BASE-BX

As shown in the previous figure, the transmit (Tx) and receive (Rx) pathsshare the same fiber by using two different wavelengths. One modeltransmits at 1310 nm and receives at 1490 nm, while the mating modeltransmits at 1490 nm and receives at 1310 nm. You can only connect amating pair.


NN46220-301 02.01 Standard25 July 2008


.


You can use 1000BASE-BX SFPs to double the number of your fiber links.For example, if you have 20 installed fiber pairs with 20 conventional portsconnected, you can use 1000BASE-BX SFPs to expand to 40 ports, usingthe same fiber.

The long wavelength optical transceivers used in these models providevariable distance ranges using single mode fiber optic cabling.

The following table describes standards, connectors, cabling, anddistances for the 1000BASE-BX SFP.

CAUTIONRisk of equipment damageConnect 1000BASE-BX SFP AA1419076-E6 to 1000BASE-BXSFP AA1419077-E6 using a single mode fiber with at least 6 dBof attenuation. Damage can result if insufficient attenuation isprovided or if the same 1000-BASE-BX SFPs are connected.

Table 27IEEE 802.3ah 1000BASE-BX10 and 1000Base-BX40 SFP specifications


Connectors Single-fiber LC



Distance AA1419069-E6 and AA1419070-E6: Up to 10kmAA1419076-E6 and AA1419077-E6: Up to 40km with SMF

Wavelength 1310 nm and 1490 nm

Link optical power budget AA1419069-E6 and AA1419070-E6: 11.0 dBAA1419076-E6 and AA1419077-E6: 20.0 dB

Maximum transmitter and dispersion powerpenalty

3.3 dB


Maximum launch power AA1419069-E6 and AA1419070-E6: -3.0 dBmAA1419076-E6 and AA1419077-E6: 3.0 dBm

Minimum launch power AA1419069-E6 and AA1419070-E6: -9.0 dBmAA1419076-E6 and AA1419077-E6: -3.0 dBm


Minimum receiver sensitivity AA1419069-E6 and AA1419070-E6: -19.5 dBmAA1419076-E6 and AA1419077-E6: -23.0 dBm

Maximum input power (maximum averagereceive power)

-3.0 dBm


NN46220-301 02.01 Standard25 July 2008


.

1000BASE-EX DDI SFP specifications 71

1000BASE-EX DDI SFP specificationsThe following table describes the 1000BASE-EX DDI SFP. This SFPoperates at 1550 nm and has a reach of up to 120 km. The part number ofthis SFP is AA1419071-E6.

CAUTIONRisk of equipment damageTo prevent damage to the optical receiver, ensure that at least14 dB of attenuation is present between the transmit andreceive ports.

To attain the BER of 10-12, the minimum attenuation betweenthe transmit and receive ports is 15 dB.

Table 281000BASE-EX DDI SFP specifications




Cabling SMF, 9 µm




Maximum dispersion power penalty 2.0 dB at 120 km







NN46220-301 02.01 Standard25 July 2008


.



NN46220-301 02.01 Standard25 July 2008


.

73.

GBIC specificationsATTENTIONThe Gigabit Interface Converters, GBIC (AA1419001 to AA1419004, AA1419017to AA1419024, and AA1419041) are no longer supported

This section provides technical specifications for the supported Gigabitinterface converter (GBIC) models. Use the specifications to help ensureproper network operation.

Navigation• “GBIC labels” (page 73)

• “General GBIC specifications” (page 74)

• “1000BASE-T GBIC specifications” (page 74)

• “1000BASE-SX GBIC specifications” (page 75)

• “1000BASE-LX GBIC specifications” (page 76)

• “1000BASE-XD GBIC specifications” (page 77)

• “1000BASE-ZX GBIC specifications” (page 78)

• “1000BASE-EX CWDM GBIC specifications” (page 79)

GBIC labelsAs shown in the following figure, the Nortel label on a typical GBICcontains a Nortel serial number, a bar code, a manufacturer’s code, aninterface type, and a part number.


NN46220-301 02.01 Standard25 July 2008


.

74 GBIC specifications

Figure 11GBIC label

General GBIC specificationsThe following table describes general GBIC specifications. GBIC portsfor both multimode (MMF) and single mode fiber (SMF) have SC-typeconnectors and a minimum cable distance of 2 meters (m).

Table 29GBIC physical specifications


Dimensions (H x W x D) 0.39 x 1.2 x 2.6 inches (in.)1.0 x 3.0 x 6.5 centimeters (cm)

Connectors • Multimode: SC

• Single mode: SC

• CAT5 RJ-45

1000BASE-T GBIC specificationsThe 1000BASE-T GBIC provides Gigabit Ethernet connectivity using asingle eight-pin RJ-45 connector. The 1000BASE-T GBIC operates at 1gigabit per second (Gbit/s) and does not support 100BASE-T or 10BASE-Tinterfaces.

The part number of this GBIC is AA1419041-E5 for the Ethernet RoutingSwitch and the Metro Ethernet Routing Switch.


NN46220-301 02.01 Standard25 July 2008


.

1000BASE-SX GBIC specifications 75

ATTENTIONYou must disable autonegotiation before operating the 1000BASE-T GBIC.By default, GBICs inserted into certain product-specific modules are setfor Autonegotiation = True. If autonegotiation does not work initially, Nortelrecommends that you reconfigure the switch to use a fixed-speed setting of1000 Mbit/s, full-duplex, on both sides.

The maximum current requirement of the GBIC is 375 milliamperes (mA)at 5 volts (V).

The following table describes the 1000BASE-T GBIC.

Table 301000BASE-T GBIC specifications


Standards IEEE 802.3z, IEEE 802.3ab

Connectors RJ-45

Cabling CAT5 unshielded twisted pair (UTP)

Distance Up to 100 m

1000BASE-SX GBIC specificationsThe 1000BASE-SX GBIC provides 1000BASE-SX Gigabit Ethernetconnectivity using SC duplex multimode fiber connectors. This GBICsupports full-duplex operation only. The part number of this GBIC isAA1419001-E5.

The following table describes standards, connectors, cabling, and distancefor the 1000BASE-SX GBIC.

CAUTIONRisk of BER increaseWhen multimode fiber is used in long-distance applications,external, removable, mode-conditioning patch cords may berequired to prevent differential mode delay (DMD). ExcessiveDMD can cause an increase in the bit error rate (BER). You canorder mode conditioning patch cords through Nortel:

• SC-SC Mode-Conditioning Patch Cord 62.5/125 (partnumber AA0018035)

• SC-SC Mode-Conditioning Patch Cord 50/125 (part numberAA0018036)


NN46220-301 02.01 Standard25 July 2008


.


CAUTIONRisk of equipment damageTo prevent damage to the optical receiver, ensure that at least10dB of attenuation is present between the transmit and receiveports.

Table 31IEEE 802.3z 1000BASE-SX GBIC specifications


Connectors Duplex SC

Cabling • 62.5 micrometer (µm) MMF

• 50 µm MMF

Distance • up to 275 m using 62.5 µm MMF

• up to 550 m using 50 µm MMF

Wavelength 850 nanometers (nm)



Launch power -10 to -4.0 decibels referenced to 1 milliwatt(dBm)




1000BASE-LX GBIC specificationsThe 1000BASE-LX GBIC provides 1000BASE-LX Gigabit Ethernetconnectivity using SC duplex fiber connectors. The long wavelength opticaltransceivers used in the LX model provide variable distance ranges usingboth multimode and single mode fiber cabling. The 1000BASE-LX GBICsupports full-duplex operation only. The part number of this GBIC isAA1419002-E5.

CAUTIONRisk of BER increaseWhen multimode fiber is used in long-distance applications,external, removable, mode-conditioning patch cords may berequired to prevent differential mode delay (DMD). ExcessiveDMD can cause an increase in the bit error rate (BER). You canorder mode conditioning patch cords through Nortel:

• SC-SC Mode-Conditioning Patch Cord 62.5/125 (partnumber AA0018035)

• SC-SC Mode-Conditioning Patch Cord 50/125 (part numberAA0018036)


NN46220-301 02.01 Standard25 July 2008


.

1000BASE-XD GBIC specifications 77

The following table describes standards, connectors, cabling, and distancefor the 1000BASE-LX GBIC.

Table 32IEEE 802.3z 1000BASE-LX GBIC specifications


Standards IEEE 802.3z, 1000BASE-LX

Connectors Duplex SC

Cabling • 62.5 µm MMF

• 50 µm MMF

• 10 µm SMF

Distance • up to 550 m using 62.5 µm MMF

• up to 550 m using 50 µm MMF

• up to 10 km using 10 µm SMF

Wavelength 1310 nm

Link optical power budget 10.5 decibels (dB)






1000BASE-XD GBIC specificationsThe 1000BASE-XD GBIC provides Gigabit Ethernet connectivity usingSC duplex single mode fiber connectors. High-performance opticaltransceivers enable Gigabit Ethernet link distances of up to 50 kilometers(km) over single mode fiber. The GBIC operates in full-duplex mode only.The part number of this GBIC is AA1419003-E5.


The following table describes standards, connectors, cabling, and distancefor the 1000BASE-XD GBIC.


NN46220-301 02.01 Standard25 July 2008


.


Table 33IEEE 802.3z 1000BASE-XD GBIC specifications


Connectors Duplex SC single mode

Cabling SMF




Wavelength 1550 ± 10 nm

Launch power -5.0 to 0 dBm


Wavelength 1200 to 1620 nm



1000BASE-ZX GBIC specificationsThe 1000BASE-ZX GBIC provides Gigabit Ethernet connectivity usingSC duplex single mode fiber connectors. High-performance opticaltransceivers enable Gigabit Ethernet link distances up to 70 km over singlemode fiber cable. The GBIC operates in full-duplex mode only. The partnumber of this GBIC is AA1419004-E5.

CAUTIONRisk of equipment damageWhen shorter lengths of single mode fiber cable are used,there is a risk of overloading the receiver. It may be necessaryto insert an in-line optical attenuator in the link to preventoverloading, as follows:

• Insert a 10 dB in-line optical attenuator between the fiberoptic cable plant and the receiving port on the 1000BASE-ZXGBIC, at each end of the link, if the fiber optic cable span isless than 25 km.

• Insert a 5 dB in-line optical attenuator between the fiber opticcable plant and the receiving port on the 1000BASE-ZXGBIC, at each end of the link, if the fiber optic cable span isless than 50 km.

The following table describes standards, connectors, cabling, and distancefor the 1000BASE-ZX GBIC.


NN46220-301 02.01 Standard25 July 2008


.

1000BASE-EX CWDM GBIC specifications 79

Table 34IEEE 802.3z 1000BASE-ZX GBIC specifications


Connectors SC duplex

Cabling SMF




Wavelength 1550 ± 10 nm

Maximum spectral width 0.2 nm



Wavelength 1200 nm to 1620 nm



1000BASE-EX CWDM GBIC specificationsThis section provides technical specifications for the coarse wavelengthdivision multiplexing (CWDM) 1000BASE-EX GBIC models. The partnumbers of these GBICs range from AA1419017-E5 to AA1419024-E5.

Table 35CWDM GBIC specifications


Connectors SC

Cabling SMF, 9 µm

Data rate 0.0125 to 1.25 Gbit/s

Total system budget@ 1.25 Gbit/sBER < 10-9 w/PRBS 27-1

30 dB — Total system budget is defined as Pout - Pin - typicalconnector losses.

Data format Electrical 8B/10B; optical 64B/66B

Operating temperature(case temperature)

0 to 70C



The following table describes CWDM GBIC optical characteristics. In thistable, the center wavelength range "x" is 1470, 1490, 1510, 1530, 1550,1570, 1590, or 1610 nm.


NN46220-301 02.01 Standard25 July 2008


.


Table 36CWDM GBIC optical specifications

Parameter Symbol Minimum Typical Maximum

Transmitter center wavelengthrange (nm) for a case temperatureof 0 to 70C

λ c (x-4) (x+1) (x+7)

Transmitter center wavelengthrange (nm) for a case temperatureof 0 to 60C

λ c (x-4) (x+1) (x+6)

Wavelength temperaturedependence

0.08 nm/C

Side mode suppression ratio SMSR 30 dB

Transmitter optical output power(average power coupled into singlemode fiber)

Pout +2.0 dBm +6.0 dBm

Transmitter extinction ratio OMI 9 dB

Transmitter eye opening (conformswith IEEE 802.3 and Fibre ChannelEye Masks)

60%

Optical return loss ORL 14 dB

Input wavelength λ in 1450 nm 1620 nm

Receiver optical input power (BER< 10-9 w/PRBS 27-1) at 1.25 Gb/s,60C case temperature.

Pin -30 dBm -7 dBm

Receiver optical input power (BER< 10-9 w/PRBS 27-1) at 1.25 Gb/s,70C case temperature.

Pin -28 dBm -7 dBm

Dispersion power penalty at 60 km 2.0 dB

Dispersion power penalty at 100 km 3.0 dB

The following table describes the CWDM GBIC electrical power interfacespecifications.

Table 37Electrical power interface specifications

Parameter Symbol Minimum Typical Maximum

Supply current Is 250 mA 300 mA

Maximum voltage Vmax 6 V

Surge current Isurge 350 mA

Input voltage Vcc 4.75 V 5.00 V 5.25 V


NN46220-301 02.01 Standard25 July 2008


.

81.

XFP specificationsThis section provides technical specifications for the supported 10 GigabitSFP (XFP) models. Use these specifications to aid in network design.The specifications provided here are a subset of the IEEE 802.3ae and802.3aq specifications. For more details, see these standards documents.All Nortel XFPs meet or exceed these standards.

ATTENTIONNortel recommends that you only use Nortel-qualified XFPs. If you do chooseto use other vendor XFPs, be aware that Nortel does not support the use ofother XFPs.

Information about SFP and XFP power consumption has been added toInstallation—Modules, NN46220-306 in a section entitled "SFPs, XFPs, Rand RC modules, and power consumption".

Navigation• “XFP labels” (page 81)

• “General XFP specifications” (page 82)

• “10GBASE-SR XFP specifications” (page 82)

• “10GBASE-LR/LW XFP specifications” (page 84)

• “10GBASE-ER/EW XFP specifications” (page 85)

• “10GBASE-ZR/ZW XFP specifications” (page 87)

• “10GBASE DWDM XFP specifications” (page 88)

XFP labelsThe Nortel label on a typical XFP contains a Nortel serial number, a barcode, a manufacturer’s code, an interface type, and a part number.


NN46220-301 02.01 Standard25 July 2008


.

82 XFP specifications

Figure 12XFP label

General XFP specificationsThe following table describes general XFP specifications.

Table 38General XFP specifications


Dimensions (H x W x D) 0.49 x 0.72 x 2.79 inches (in.)

12.5 x 18.35 x 71.1 millimeters (mm)

Connectors LC ultra physical contact (UPC)


Operating temperature -40 to 80C for RoHS - E6 models

0 to 70C for RoHS - E5 models

-5 to 70C for RoHS - E5 (DWDM XFPs)

10GBASE-SR XFP specificationsThe 10GBASE-SR SFP provides 10 GbE service at 850 nm. This SFPcan attain a reach of up to 300 m.

The following table lists the transmitter specifications for the 10GBASE-SRXFP. The part number of this XFP is AA1403005-E5.

For more information about the 10GBASE-SR XFP, including test andmeasurement information, see the IEEE 802.3ae standard.


NN46220-301 02.01 Standard25 July 2008


.

10GBASE-SR XFP specifications 83


Table 39IEEE 802.3ae 10GBASE-SR XFP specifications



Line rate (64B/66B code) 10.3125 gigabits per second (Gbit/s) ± 100 parts permillion (ppm)

Mean Time Between Failures (MTBF) 675 000 hours

Center wavelength range 840 to 860 nanometers (nm), nominal 850 nm

Distance Using 62.5 µm MMF optic cable

• 160 MHz-km fiber: 2 m to 26 m


Using 50 µm MMF• 400 MHz-km fiber: 2 m to 66 m




Maximum transmitter and dispersionpenalty

3.9 dB at 300 m


Root-mean-square spectral width 0.05 to 0.40 nm

Launch power -7.3 to -1.0 decibels referenced to 1 milliwatt (dBm)

Maximum average launch power of OFFtransmitter

-30 dBm

Minimum extinction ratio 3.0 dB

Maximum relative intensity noise 12OMA -128 dB per Hertz (dB/Hz)

Maximum optical return loss tolerance -12 dB


Maximum average receive power -9.9 to -1.0 dBm

Maximum average receive power fordamage

0 dBm

Maximum receiver sensitivity in OMA(see Note 1)

-11.1 dBm


NN46220-301 02.01 Standard25 July 2008


.


Table 39IEEE 802.3ae 10GBASE-SR XFP specifications (cont’d.)


Maximum receiver reflectance -12 dB

Stressed receiver sensitivity in OMA(see Note 2)

-7.5 dBm

Receiver electrical 3 dB upper cutofffrequency

12.3 gigaHertz (GHz)

Note 1: Receiver sensitivity is informative.Note 2: Measured with conformance test signal for BER = 10-12

The stressed sensitivity values are for system level BER measurements,which include the effects of CDR circuits. Nortel recommends that youallocate at least 0.4 dB additional margin if you make component levelmeasurements without the effect of CDR circuits.

10GBASE-LR/LW XFP specificationsThe 10GBASE-LX SFP provides 10 GbE service at a nominal wavelengthof 1310 nm. This XFP can attain link lengths of up to 10 km.

The following table lists the transmitter specifications for the10GBASE-LR/LW XFP. The part number of this XFP is AA1403001-E5.

For more information about the 10GBASE-LX XFP, including test andmeasurement information, see the IEEE 802.3ae standard.

ATTENTIONYou can configure the XFP to operate in either LAN (Ethernet) or WAN (SONET)mode, depending on the module (8683XLR is a LAN-only module, and 8683XZRis a LAN/ WAN module). Model numbers ending in R denote a LAN interface;model numbers ending in W denote a WAN interface.

Table 40IEEE 802.3ae 10GBASE-LR/LW XFP specifications


MTBF 675 000 hours

Center wavelength range 1260 to 1355 nm; 1310 nm nominal



Maximum transmitter and dispersion penalty 3.2 dB at 10 km


Line rate (nominal) 10GBASE-LR 10.3125 Gbit/s ±100 ppm10GBASE-LW 9.95328 Gbit/s ±20 ppm


NN46220-301 02.01 Standard25 July 2008


.

10GBASE-ER/EW XFP specifications 85

Table 40IEEE 802.3ae 10GBASE-LR/LW XFP specifications (cont’d.)


Average launch power -8.2 to 0.5 dBm

Minimum side mode suppression ratio 30 dB

Minimum launch power in OMA minustransmission and dispersion penalty (TDP)

-6.2 dBm

Minimum optical modulation amplitude -5.2 dBm

Maximum average launch power of OFFtransmitterc

-30 dBm


RIN12OMA (maximum) -128 dB/Hz

Maximum optical return loss tolerance 12 dB

Maximum transmitter reflectance 12 dB


Line rate (nominal) 10GBASE-LR 10.3125 Gbit/s ± 100 ppm10GBASE-LW 9.95328 Gbit/s ± 100 ppm

Average receive power -14.4 dBm to 0.5 dBm

Maximum average receive power for damage 1.5 dBm

Maximum receiver sensitivity in OMA -12.6 dBm

Maximum receiver reflectance 12 dB

Stressed receiver sensitivity in OMA -10.3 dBm

Receiver electrical 3 dB upper cutoff frequency 12.3 GHz

Examples of an OFF transmitter are: no power supplied tothe PDM, laser shutdown for safety conditions, activation of aPMD_global_transmit_disable or other optional transmitter shut downcondition.

10GBASE-ER/EW XFP specificationsThe following table lists the transmitter specifications for the10GBASE-ER/EW XFP. The reach for this XFP is up to 40 km at awavelength of 1550 nm. The part number of this XFP is AA1403003-E5.

For more information about the 10GBASE-EX XFP, including test andmeasurement information and more specifications, see the IEEE 802.3aestandard.


NN46220-301 02.01 Standard25 July 2008


.



Table 41IEEE 802.3ae 10GBASE-ER/EW XFP specifications


Line rate (nominal) 10GBASE-ER 10.3125 Gbit/s ±100 ppm10GBASE-EW 9.95328 Gbit/s ±20 ppm

MTBF 675 000 hours

Center wavelength range 1530 to 1565 nm; nominal 1550 nm



Transmitter and dispersion power penalty 3.0 dB at 40 km



Minimum side mode suppression ratio 30 dB

Minimum launch power in OMA minustransmission and dispersion penalty (TDP)

-2.1 dBm

Minimum optical modulation amplitude -1.7 dBm

Maximum average launch power of OFFtransmitter

-30 dBm


Maximum RIN12OMA -128 dB/Hz



Average receive power -15.8 dBm to -1.0 dBm

Maximum receive power for damage 4.0 dBm

Maximum receiver sensitivity in OMA -14.1 dBm

Maximum receiver reflectance 26 dB

Stressed receiver sensitivity in OMA -11.3 dBm

Receive electrical 3 dB upper cutoff frequency(maximum)

12.3 GHz

Examples of an OFF transmitter are: no power supplied tothe PDM, laser shutdown for safety conditions, activation of aPMD_global_transmit_disable or other optional transmitter shut downconditions.


NN46220-301 02.01 Standard25 July 2008


.

10GBASE-ZR/ZW XFP specifications 87

10GBASE-ZR/ZW XFP specificationsThe following table lists the transmit specifications for the10GBASE-ZR/ZW XFP. The reach is up to 80 km at a wavelength of 1550nm. The part number of this XFP is AA1403006-E5.

For more information about the 10GBASE-ZX XFP, including test andmeasurement information and more specifications, see the IEEE 802.3aestandard.


ATTENTIONTo assure proper link operation, ensure that at least 11 dB of attenuation ispresent between the transmit and receive ports.

Table 4210GBASE-ZR/ZW XFP specifications


Line rate (nominal) 10GBASE-ZR 10.3125 Gbit/s ±100 ppm10GBASE-ZW 9.95328 Gbit/s ±20 ppm

MTBF 675 000 hours

Center wavelength range 1530 to 1565 nm; nominal 1550 nm



Maximum transmitter and dispersion penalty 3.0 dB at 80 km (G.652 fiber)


Side mode suppression ratio (minimum) 30 dB

Average launch power 0 to 4.0 dBm

Optical modulation amplitude (minimum) 1.25 dBm (ZR = 7 dBm)

Average launch power of OFF transmitter(maximum)

-30 dBm

Extinction ratio minimum 3.5 dB end of lifemaximum 7.0 dB start of life

RIN12OMA (maximum) -128 dB/Hz


Maximum transmitter reflectance -12 dB



NN46220-301 02.01 Standard25 July 2008


.


Table 4210GBASE-ZR/ZW XFP specifications (cont’d.)


Signaling speed (nominal) 10GBASE-ZR 10.3125 Gbit/s ± 100 ppm10GBASE-ZW 9.95328 Gbit/s ± 100 ppm

Maximum average receiver sensitivity -24 dBm

Maximum receive power (for damage) 5 dBm

Receiver reflectance (maximum) -27 dB

Receive electrical 3 dB upper cutoff frequency 9.3 GHz

10GBASE DWDM XFP specificationsThe following table lists the transmit specifications for the 10GBASEDWDM XFP. The reach is up to 80 km at a center wavelength specific toeach product engineering code (PEC). The part number of this XFP isNTK587AY/BA/BC/BE/BG/BJ/BL/BN/BQ/BS/BU.

CAUTIONRisk of equipment damage or BER increaseTo prevent damage to the optical receiver, ensure that atleast 2 dB of attenuation is present between the transmit andreceive ports. For proper XFP operation, ensure that 10 dB ofattenuation is present between the transmit and receive ports.

Table 4310GBASE DWDM OC-192 XFP specifications


Line rate 10GBASE DWDM 10.3125 Gbit/s ±100 ppm10GBASE DWDM 9.95328 Gbit/s ±100 ppm

MTBF 4 x 106 hours

Center wavelength range 1537.40 nm to 1545.32 nm

Distance Up to 80 km (on NDSF fiber)


Maximum transmitter and dispersion penalty 3 dB at 1600 ps/nm km (OSNR > 30 dB)


Side mode suppression ratio (minimum) 40 dB

Average launch power -1 to + 3 dBm

Extinction ratio Minimum 8.2 dB end of life

RIN (maximum) -130 dB/Hz



NN46220-301 02.01 Standard25 July 2008


.

10GBASE DWDM XFP specifications 89

Table 4310GBASE DWDM OC-192 XFP specifications (cont’d.)

Signaling speed (nominal) 10GBASE DWDM 10.3125 Gbit/s ±100 ppm10GBASE DWDM 9.95328 Gbit/s ±100 ppm

Maximum average receiver sensitivity - 24.5 dBm (back-to-back, OSNR > 30 dB)

Maximum receive power (for damage) +1.0 dBm

Receiver reflectance (maximum) -27 dB

Polarization Mode Dispersion (PMD) minimumtolerance (the amount of PMD which causes1 dB OSNR penalty at 10.3125 Gb/s) PeakDifferential Group Delay (DGD)

15 ps

Note: Due to hexidecimal to decimal rounding, and vice-versa, the wavelength numbers providedby the XFP manufacturer and reported by the Metro Ethernet Routing Switch 8600 system mayvary slightly.

Table 44DWDM XFP wavelengths

Part Number Wavelength and frequency

The wavelength specifications provided by the XFP manufacturer and reported by the MetroEthernet Routing Switch 8600 system may vary slightly because of hexadecimal to decimal (anddecimal to hexadecimal) rounding.

NTK587AYE5 1537.40 nm [195.0 Terahertz (THz)]

NTK587BA-E5 1538.19 nm (194.9 THz)

NTK587BC-E5 1538.98 nm (194.8 THz)

NTK587BE-E5 1539.77 nm (194.7 THz)

NTK587BG-E5 1540.56 nm (194.6 THz)

NTK587BJ-E5 1541.35 nm (194.5 THz)

NTK587BL-E5 1542.14 nm (194.4 THz)

NTK587BN-E5 1542.94 nm (194.3 THz)

NTK587BQ-E5 1543.73 nm (194.2 THz)

NTK587BS-E5 1544.53 nm (194.1 THz)

NTK587BU-E5 1545.32 nm (194.0 THz)


NN46220-301 02.01 Standard25 July 2008


.



NN46220-301 02.01 Standard25 July 2008


.

91.

Multiplexer specificationsThis section describes multiplexer specifications. Use the specificationsto help ensure proper network operation. Multiplexer loss values includeconnector loss.

There is one nanometer (nm) offset between the stated wavelength forthe Coarse Wavelength Division Multiplexing (CWDM) Gigabit InterfaceConverters (GBIC) and the CWDM optical add/drop multiplexers (OADM)due to a shift in the center wavelength of the CWDM GBIC as it reachestypical system operating temperature.

Table 45Multiplexer specifications

Parameter Specification

Physical dimensions Plug-in module sizeRack mount

8.35" x 1.7" x 10.4"1 rack unit (RU)

Connectors Network sideEquipment side

2 dual SC/PC2 dual SC/PC

Cabling SMF, 9 µm

Environment OperatingStorage

9 to 60C40 to 85C

Wavelength usage Unidirectional

Typical insertion loss TX to RX Network (add)RX to TX Network (drop)

Passthrough (Network toNetwork)

1.2 decibels (dB)1.6 dB

1.5 dB

Maximum insertion loss TX to RX Network (add)RX to TX Network (drop)


1.9 dB2.3 dB

2.0 dB


NN46220-301 02.01 Standard25 July 2008


.

92 Multiplexer specifications

Table 45Multiplexer specifications (cont’d.)

Sigma TX to RX Network (add)RX to TX Network (drop)


.35 dB

.35 dB

.40 dB

Isolation TX to RX Network (add)RX to TX Network (drop)


> 25 dB> 50 dB

> 28 dB

Passband Center wavelength +/- 5 dB

Directivity < - 55 dB

Optical Wavelengths 1471 nm1491 nm

1511 nm

1531 nm

1551 nm

1571 nm

1591 nm

1611 nm


NN46220-301 02.01 Standard25 July 2008


.

93.

Index

1000BASE-BX 34, 37, 691000BASE-EX 34, 37, 791000BASE-EX DDI 711000BASE-LX 34–36, 42, 621000BASE-LX DDI 641000BASE-LX GBIC specifications 761000BASE-SX 34–36, 42, 60–611000BASE-SX DDI 641000BASE-SX GBIC specifications 751000BASE-T 34, 36, 42, 601000BASE-T GBIC specifications 741000BASE-XD 34, 36, 421000BASE-XD DDI 65–661000BASE-XD GBIC specifications 771000BASE-ZX 34, 36, 421000BASE-ZX DDI 661000BASE-ZX GBIC specifications 78100BASE-BX10-U/D 58100BASE-FX 57100BASE-LX 58100BASE-ZX 5910GBASE DWDM 4710GBASE-ER/EW 4610GBASE-ER/EW XFP specifications 8510GBASE-LR/LW 4610GBASE-LR/LW XFP specifications 8410GBASE-SR 4610GBASE-SR XFP specifications 8210GBASE-ZR/ZW 4710GBASE-ZR/ZW XFP specifications 87

AAA1403001-E5 46, 84AA1403003-E5 46, 85AA1403005-E5 46, 82AA1403006-E5 47, 87AA1419001-E5 42, 75

AA1419002-E5 42, 76AA1419003-E5 42, 77AA1419004-E5 42, 78AA1419013-E5 35, 60AA1419014-E5 35, 61AA1419015-E5 35, 62AA1419017-E5 42, 79AA1419024-E5 42, 79AA1419025-E5 35, 62AA1419032-E5 35, 62AA1419033-E5 35, 63AA1419040-E5 35, 63AA1419041-E5 42, 74AA1419043-E6 36, 60AA1419048-E6 36, 64AA1419049-E6 36, 64AA1419050-E6 36, 65AA1419051-E6 36, 66AA1419052-E6 36, 66AA1419053-E6 36, 67AA1419060-E6 36, 67AA1419061-E6 36, 68AA1419068-E6 36, 68AA1419069-E6 37, 69AA1419070-E6 37, 69AA1419071-E6 37, 71AA1419074-E6 57AA1419076-E6 37AA1419077-E6 37AA1419081-E5 58AA1419082-E5 58AA1419083-E5 58AA1419084-E5 59acronyms 21


NN46220-301 02.01 Standard25 July 2008


.

94

Ccleaning, handling fiber optic

connectorsduplex SC connectors 27receptacle or duplex devices 27SC, FC connectors 26tools and materials 26

CWDM DDI SFPs 67–68CWDM GBIC specifications 79CWDM SFPs 62–63

Ddifferential mode delay 75–77duplex devices, cleaning 27duplex SC connectors, cleaning 27

Eelectrostatic discharge 24

FFC connectors, cleaning 26fiber optic cable

cleaning connectors for 25precautions with 24

GGBIC

1000BASE-SX 751000BASE-XD 77

GBIC physical specifications 74

Mmulti-mode fiber

in long distance applications 75–77

Ooptical attenuators,

when to use 78

Ppatch cords,

for multimode fiber applications 75–77

Rreceptacle devices, cleaning 27

Ssafety 23SC connectors, cleaning 26SFP

1000BASE-BX 691000BASE-LX 621000BASE-SX 60–611000BASE-T 60100BASE-BX10-U/D 58100BASE-LX 58100BASE-ZX 59

SFP physical specifications 57

Ttroubleshooting 44

XXFP specifications 82


NN46220-301 02.01 Standard25 July 2008


.

Nortel Metro Ethernet Routing Switch 8600

Installation — SFP, XFP, GBIC, and OADM HardwareComponentsCopyright © 2006-2008 Nortel NetworksAll Rights Reserved.

Printed in Canada, India, and the United States of AmericaRelease: 5.1Publication: NN46220-301Document status: StandardDocument revision: 02.01Document release date: 25 July 2008

To provide feedback or to report a problem in this document, go to www.nortel.com/documentfeedback.

www.nortel.comLEGAL NOTICEWhile the information in this document is believed to be accurate and reliable, except as otherwise expressly agreed to in writingNORTEL PROVIDES THIS DOCUMENT "AS IS" WITHOUT WARRANTY OR CONDITION OF ANY KIND, EITHER EXPRESSOR IMPLIED. The information and/or products described in this document are subject to change without notice.

Nortel, the Nortel logo, the Globemark, and Unified Networks are trademarks of Nortel Networks.All other trademarks are the property of their respective owners.

ATTENTION

For information about the regulatory message, read "Regulatory Information" in this guide.

For information about the software license, read "Software license" in this guide.

Nortel Metro Ethernet Routing Switch 8600 Installation — SFP, XFP, GBIC, and OADM Hardware ...

Documents

Transcript of Nortel Metro Ethernet Routing Switch 8600 Installation — SFP, XFP, GBIC, and OADM Hardware ...