No. Products Model No. Pagef02.s.alicdn.com/kf/UT8XJDDXaldXXc_PVbXJ.pdf• 5.1 channel Dolby Digital...
Transcript of No. Products Model No. Pagef02.s.alicdn.com/kf/UT8XJDDXaldXXc_PVbXJ.pdf• 5.1 channel Dolby Digital...
DATASHEETS
No. Products Model No. Page
1. DSNG Encoder DMP-9724SNG 2
2. MPEG-2/4 AVC HD Encoder (4:2:2) DME-9724HM 4
3. MPEG-2/4 AVC HD Encoder (4:2:2) DME-9724H 6
4. MPEG-2/4 AVC HD Encoder (4:2:0) DME-9624H 8
5. MPEG-2/4 AVC HD Encoder (4:2:0) DME-9524H 10
6. Multi 8 Channel SD Encoder DME-8624S8 12
7. MPEG-2/4 AVC SD Encoder DME-8624S 14
8. Integrated Receiver / Decoder DMD-9724IRD 16
9. MPEG Decoder DMD-9724D 18
10. MPEG HD Mediaplex (4:2:2) DMP-9724M 20
11. MPEG HD Mediaplex (4:2:0) DMP-9624M 22
12. MPEG HD Mediaplex (4:2:0) DMP-9524M 24
13. ISDB-T Multiplexer DMX-1908ST 26
14. DVB-T2 Gateway DMX-1908T2 28
15. Management System NMS 30
16. 8-VSB Modulator DVM-1903ML 31
17. QAM Modulator DQM-1903ML 32
18. IPASI Converter DIC-500 33
19. Multi Digital Scaler DSR-1000 34
20. HDMI to SDI Scaler DSR-500 35
21. Multi Media Converter MMC-1000 36
22. Media Converters ATS-500 37
23. Media Converters STH-500 / HTS-500 38
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
DMP-9724SNG designed for Teleports, Digital Satellite News Gathering Vehicles, and it is operating on either the C, Ku or Ka-bands.As a representative model of CASTWIN, it is the best performing and fully programmed high-end encoding. Also, it has DVB-S/S2 modulation with the highest video quality and the lowest latency.
Encoding & DVB-S/S2 Modulation
Latency 150ms
Chroma Format 4:2:0 4:2:2
Resolutions up to 1080p
L-Band or IF output
• Component, Composite, HDMI, HD/SD-SDI video inputs• Ultra low latency as 150ms• Up to 1080p supported• Support 4:2:0(8bit), 4:2:2(10bit)• Digital, Analog and SDI embedded audio(8channel) inputs• 5.1 channel Dolby Digital (AC-3) encoding support • 7.1 channel SPDIF audio optical input (pass through)• Additional 1xASI input for supporting of insertion of externally generated PSIP into the transport stream
• Provides internally generated PSI, PSIP, SI• Control of Frame rate• Selectable MPEG-2 HD or H.264 HD real-time video encoding• Simultaneous outputting of 2xTransport stream (ASI) with UDP/IP or RTP/IP transport stream.
• Dolby Digital (AC-3), MPEG-1 Layer II, AAC-LC, HE-AAC audio encoding
• Supports EIA-708 Closed caption insertion via HD SDI(SMPTE 334).
• Supports internally generated TVCT, CVCT, SDT, NIT• Excellent IP converter integrated performance
-Much lower latency & stable IP output• Control and monitoring via web browser, front panel, or SNMP• 4 channel AES/EBU Digital Audio • 4 stereo (8channel) Analog input with D-sub type • Integrated Advanced Scaler function
- Control of Frame rate, Image enhance- Phase Noise, Correction of Color, Control of Gamma
• L-Band Output 950 ~2150 MHz or IF Output 50 ~ 180 MHz• DVB-S/S2 Modulation• BISS mode-1 and BISS mode-E support• Designed for Teleports, Digital Satellite News Gathering Vehicles• Operating on either the C, Ku or Ka-bands• Symbol Rate: 1 Mbaud ~ 68 Mbaud
Feature
• Providing your viewers with the best performance compression and flawless picture quality
• Wide use in many projects with high compatibility supporting various formats
• Best choice for broadcasting of racing, sports via real time encoding with ultra low latency, at 150ms
• Reduce the cost of transmission as supporting wide range of bit-rate control and advanced video coding techniques
• Able to Secure space with compact size for installing
Competitiveness
DSNG Encoder
DMP-9724SNG
Options
• IP Streaming output
2
DSNG Encoder
DMP-9724SNG
DSNG Encoder www.castwin.com Digital Products MPEG Encoders
Specifications
Configuration
ITEM CHARACTER
Video Input
Analog Input Composite, ComponentLevel 1 Vp-p
Digital Input HDMI, HD-SDILevel 1000 mVp-p (HDMI) 800mVp-p (HD-SDI)
Resolutions 480i29.97, 576i25, 720p50/59.94,1080i25/29.97, 1080p25/29.97
SD Aspect Ratio 4:3, 16:9
Audio Input
AnalogInput 4 StereoFreq. Range 20 Hz ~ 20 KHzImpedance 600 Ω Connector D-SUB 15pin x 2
Digital Input 4 x AES-EBU, Embedded SDI/HDMI (4 Stereo 8 Channel)Sampling Rate 32, 44.1 and 48 KHzConnector BNC (75Ω) / HDMI-19PIN
Optical Input SPDIF(7.1 Channel) pass through
Video Encoder
Encoding MPEG-2 HP@HL, MP@HL , [email protected] HP@L4, MP@L3
Encoding Rate MPEG-2 : 0.6~50 Mbps , H.264 : 0.6~50 MbpsChroma Depth 4:2:0(8bit), 4:2:2(10bit)PSNR 38 dBBit Rate Mode CBR,VBRLatency 150 ms~
Audio Encoder
Input Sampling Rate 32, 44.1, 48 KHzOutput sampling Rate 48 KHz
EncodingMPEG-1 Layer II (2ch) AC-3 (2ch) AC-3 Pro (2ch, 5.1ch)AAC LC (2ch, 5.1ch) HE-AAC v1 (5.1ch) HE-AAC v2 (2ch)
Audio Mix 4 Stereo (8channel) or 5.1chBit Rate AC-3 128, 192, 256, 384 KHz
AC-3 Pro 96, 112, 128, 160, 192, 224, 256, 320, 384 KHzMPEG1 64, 96, 112, 128, 160, 192, 224, 256, 320, 384 KHz AAC LC 32,48,56,64,80,96,112, 128,160,192, 224, 256, 320,384 KHzHE AAC v2 32, 48, 56, 64, 80, 96 KHzAC-3 Pro 5.1 224, 256, 320, 384, 448, 576, 640 KHzAAC LC 5.1 96, 112, 128, 160, 192, 224, 256, 320, 384 KHzHE AAC v1 5.1 96, 112, 128, 160, 192, 224, 256 KHz
Delay -100 ~ 400 ms
TS Input
Transport Stream DVB-ASI 1port
DVB-S
Mode code QPSK, 8PSK, 16QAM Connector BNC (75 Ω) Roll-Off 0.05 ~ 0.35 Packet Format 188 Byte BISS Mode (1,E Injected, E Buried) Output Level 800 mVp-p Symbol Rate 1 ~ 68Mbauds
TS Output
Transport Stream ASI 2portConnector BNC (75 Ω)
DVB-S2
Mode code QPSK, 8PSK, 16APSK, 32APSK
TS Bit RateMPEG-2 : 2.5~55 Mbps , Roll-Off 0.05 ~ 0.35 H.264 : 2.5~55 Mbps BISS Mode (1,E Injected, E Buried)
Packet Format 188 Byte Symbol Rate 1 ~ 68Mbauds
IP TS Output(Option)
Output 1 port Pilot Insertion
Connector RJ-45 Operating Mode CCM only Ethernet type 10/100/1000 Base-T Frame Type Normal / Short Stream Protocol UDP/IP, RTP/IPBroadcasting Multicast, Unicast
RF Option
Reverse Spectrum
TS Bit rate MPEG-2 : 2.5~55 Mbps , Tilt Correction -0.040 ~ 0.040 dB/MHz H.264 : 2.5~55 Mbps Carrier Modulator
Ethernet
Connector RJ-45 Out Level -35.00 ~+5.00 dBm
Interface Type 10/100 Base-T L-Band 950 ~ 2150 MHz
Protocols SNMP IF 50/180MHz
General
Power Requirements AC 90~230 V, 50/60 HzPower Consumption Max. 100 WWeight 4 KgOperating Temperature -10 ~ 50 Dimensions (W x H x D) 482 x 44 x 483 mm
3
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
As a representative Encoder of CASTWIN, it is a newly released product which is the best performing and fully programmed high-end encoding with wonderful video quality and the lowest latency. DME-9724HM let you feel very much reality as if you are the part of video. Also, it enables to transmit more video channels and audio channels at the available bandwidth.
High-End Encoding
Latency 150ms
Chroma Format 4:2:0 4:2:2
Resolutions up to 1080p
• Component, Composite, HDMI, HD/SD-SDI video inputs• Ultra low latency as 150ms• Up to 1080p supported• Support 4:2:0(8 bit), 4:2:2(10 bit)• Digital, Analog and SDI embedded audio(8channel) inputs.• 5.1 channel Dolby Digital (AC-3) encoding support • 7.1 channel SPDIF audio optical input(pass through)• Additional 1xASI input for supporting of insertion of externally generated PSIP into the transport stream
• Provides internally generated PSI, PSIP, SI• Control of Frame rate• Selectable MPEG-2 HD or H.264 HD real-time video encoding• Simultaneous outputting of 2xTransport stream (ASI) with UDP/IP or RTP/IP transport stream.
• Dolby Digital (AC-3), MPEG-1 Layer II, AAC-LC, HE-AAC audio encoding
• Supports EIA-708 Closed caption insertion via HD SDI(SMPTE 334)
• Supports internally generated TVCT, CVCT, SDT, NIT• Excellent IP converter integrated performance
-Much lower latency & stable IP output• Control and monitoring via web browser, front panel, or SNMP• 4 channel AES/EBU Digital Audio • 4 stereo(8channels) analog input with D-sub type • Integrated Advanced Scaler function
- Control of Frame rate, Image enhance- Phase Noise, Correction of Color, Control of Gamma
Feature
• Providing your viewers with the best performance compression and flawless picture quality
• Wide use in many projects with high compatibility supporting various formats
• Best choice for broadcasting of racing, sports via real time encoding with ultra low latency, at 150ms
• Reduce the cost of transmission as supporting wide range of bit-rate control and advanced video coding techniques
• Able to Secure space with compact size for installing
Competitiveness
MPEG-2/4 AVC HD Encoder
DME-9724HM
4
MPEG-2/4 AVC HD Encoder
DME-9724HM
MPEG-2/4 AVC HD Encoder www.castwin.com Digital Products MPEG Encoders
Specifications
ITEM CHARACTER
Video Input
Analog Input Composite, Component
Level 1 Vp-p
Digital Input HDMI, HD-SDILevel 1000 mVp-p (HDMI) 800mVp-p (HD-SDI)
Resolutions 480i29.97, 576i25, 720p50/59.94,
1080i25/29.97, 1080p25/29.97
SD Aspect Ratio 4:3, 16:9
Audio Input
AnalogInput 4 StereoFreq. Range 20 Hz ~ 20 KHzImpedance 600 ΩConnector D-SUB 15pin x 2
DigitalInput 4 x AES-EBU, Embedded SDI/HDMI (4 Stereo 8 Channel)Sampling Rate 32, 44.1 and 48 KHzConnector BNC (75Ω) / HDMI-19PIN
Optical Input SPDIF(7.1 Channel) pass through
Video Encoder
Encoding MPEG-2 HP@HL, MP@HL , MP@ML
H.264 HP@L4, MP@L3Encoding Rate MPEG-2 : 0.6~50 Mbps , H.264 : 0.6~50 MbpsChroma Format 4:2:0, 4:2:2 (8 bit / 10 bit)PSNR 38 dBBit Rate Mode CBR,VBRLatency 150 ms~
Audio Encoder
Input Sampling Rate 32, 44.1, 48 KHz
Output sampling Rate 48 KHz
EncodingMPEG-1 Layer II (2ch) AC-3 (2ch) AC-3 Pro (2ch, 5.1ch)AAC LC (2ch, 5.1ch) HE-AAC v1 (5.1ch) HE-AAC v2 (2ch)
Audio Mix 4 Stereo (8ch) or 5.1chBit Rate AC-3 128, 192, 256, 384 KHz
AC-3 Pro 96, 112, 128, 160, 192, 224, 256, 320, 384 KHzMPEG1 64, 96, 112, 128, 160, 192, 224, 256, 320, 384 KHzAAC LC 32,48,56,64,80,96,112, 128,160,192, 224, 256, 320,384 KHzHE AAC v2 32, 48, 56, 64, 80, 96 KHzAC-3 Pro 5.1 224, 256, 320, 384, 448, 576, 640 KHzAAC LC 5.1 96, 112, 128, 160, 192, 224, 256, 320, 384 KHzHE AAC v1 5.1 96, 112, 128, 160, 192, 224, 256 KHz
Delay -100 ~ 400 ms
TS Input
Transport Stream DVB-ASI 1portConnector BNC (75 Ω)Packet Format 188 ByteOutput Level 800 mVp-p
TS Output
Transport Stream ASI 2portConnector BNC (75 Ω)TS Bit Rate MPEG-2 : 2.5~55 Mbps , H.264 : 2.5~55 MbpsPacket Format 188 Byte
IP TS Output
Output 1 portConnector RJ-45Ethernet type 10/100/1000 Base-TStream Protocol UDP/IP, RTP/IPBroadcasting Multicast, Unicast
TS Bit rate MPEG-2 : 2.5~55 Mbps , H.264 : 2.5~55 Mbps
EthernetConnector RJ-45Interface Type 10/100 Base-TProtocols SNMP
General
Power Requirements AC 90~230 V, 50/60 HzPower Consumption Max. 100 WWeight 4 KgOperating Temperature -10 ~ 50 Dimensions (W x H x D) 482 x 44 x 483 mm
Configuration
5
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
As a representative Encoder of CASTWIN, it is a newly released product which is the best performing and fully programmed high-end encoding with wonderful video quality and the lowest latency. DME-9724H let you feel very much reality as if you are the part of video. Also, it enables to transmit more video channels and audio channels at the available bandwidth.
High-End Encoding
Latency 150ms
Chroma Format 4:2:0 4:2:2
Resolutions up to 1080p
• Component, Composite, HDMI, HD/SD-SDI video inputs• Ultra low latency as 150ms• Up to 1080p supported• Support 4:2:0(8 bit), 4:2:2(10 bit)• Digital, Analog and SDI embedded audio(8channel) inputs.• 5.1 channel Dolby Digital (AC-3) encoding support • 7.1 channel SPDIF audio optical input(pass through).• Additional 1xASI input for supporting of insertion of externally generated PSIP into the transport stream.
• Provides internally generated PSI and PSIP.• Various functions with integrated Advanced Scaler.• Control of Frame rate, Image enhance, Phase Noise, Correction of Color, Control of Gamma
• Selectable MPEG-2 HD or H.264 HD real-time video encoding.
• Simultaneous outputting of 2xTransport stream (ASI) with UDP/IP or RTP/IP transport stream.
• Dolby Digital (AC-3), MPEG-1 Layer II, AAC-LC, HE-AAC audio encoding.
• Supports EIA-708 Closed caption insertion via HD SDI(SMPTE 334).
Feature
• Providing your viewers with the best performance compression and flawless picture quality
• Wide use in many projects with high compatibility supporting various formats
• Best choice for broadcasting of racing, sports via real time encoding with ultra low latency as 150ms
• Reduce the cost of transmission as supporting wide range of bit-rate control and advanced video coding techniques.
• Able to Secure space with compact size for installing
Competitiveness
MPEG-2/4 AVC HD Encoder
DME-9724H
6
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Specification
Video Input
Analog Input Component , Composite
Level 1 Vp-p
Digital Input HDMI , SDI
Level 1000 mVp-p (HDMI) 800mVp-p (SDI)
Resolutions480i29.97, 576i25, 720p50/59.94
1080i25/29.97
1080p25/29.97
SD Aspect Ratio 4:3, 16:9
Audio Input
Analog Input 1 stereo
Freq. Range 20Hz ~ 20KHz
Impedance 600 Ω
Connector Mini XLR
Digital Input AES-EBU, Embedded SDI/HDMI(8Ch)
Sampling Rate 32, 44.1, 48 KHz
Connector BNC (75Ω) / HDMI-19PIN
Optical Input SPDIF(7.1 Channel) (pass through).
Video Encoder
Encoding MPEG-2 HP@HL, MP@HL , MP@ML
H.264 HP@L4, MP@L3
Encoding Rate MPEG-2 : 2~50 Mbps
H.264 : 0.6~50 Mbps
Chroma Format 4:2:0(8bit), 4:2:2 (10bit)
PSNR 38dB
Bit Rate Mode CBR,VBR
Latency 150ms~
Audio Encoder
Sampling Rate 32, 44.1, 48KHz
Dolby Digital® AC-3(7.1CH) 128,192,256,384 Kbps
MPEG-1 Layer II 192,224,256,320,384 Kbps
MPEG-4 AAC-LC 32~384 Kbps
MPEG-4 HE-AAC v1 32~192 Kbps
MPEG-4 HE-AAC v2 32~96 Kbps
TS Input
Transport Stream ASI 1 Port
Connector BNC(75Ω)
Packet Format 188 Byte
Input Level 800mVp-p
TS Output
Transport Stream ASI 2 port
Connector BNC(75Ω)
TS Bit Rate MPEG-2 : 2.5~55 Mbps
H.264: 2.5~55 Mbps
Packet Format 188, 204 Byte
IP TS Output
Output 1 Port
Connector RJ-45
Ethernet type 10/100 Base-T
Format UDP/IP, RTP/IP
IP Address Format Multicast, Unicast
TS Bit rate MPEG-2 : 2.5~55 Mbps
H.264: 2.5~55 Mbps
TS Packet Rate 188,204 Byte
Ethernet
Connector RJ-45
Interface Type 10/100Base-T
Protocols SNMP
General
Power Requirements AC 90~230V, 50/60Hz
Power Consumption Max. 100W
Weight 4 kg
Operating Temperature -10~50°C
Dimension(W x H x D) 482 x 44 x 383 mm
Configuration
MPEG-2/4 AVC HD Encoder
DME-9724H
7
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction Feature
Competitiveness
MPEG-2/4 AVC HD Encoder
DME-9624H
CASTWIN’s High-definition encoder offering highest video quality with low latency. It shows excellent performance for inputting signal (Analog & Digital) to output as transport stream signal after compressing and encoding for suitable digital transmission with various supportedformats. Moreover, it supports both MPEG-2 and H.264 so that it makes operators select the format as they want.
• Component, Composite, HDMI, HD/SD-SDI video inputs.• Low latency as 800ms• Digital, Analog and SDI embedded audio(4ch) inputs.• 5.1 channel SPDIF audio optical input(pass through)• Additional 1xASI input for supporting of insertion of externallyGenerated PSIP into the transport stream.
• Video input Auto detection function.• Selectable MPEG-2 or H.264 HD/SD real-time videoencoding.
• Various functions with integrated Advanced Scaler.• Control of Frame rate, Image enhance, Phase Noise, Correction of Color, Control of Gamma
• Simultaneous outputting of 2xTransport stream (ASI) withUDP/IP or RTP/IP transport stream.
• Dolby Digital (AC-3), MPEG-1 Layer II, AAC-LC, HE-AAC audioencoding.
• Excellent option for operators who competitively pursue the best performing encoding device with high resolution up to 1080p
• Good option for Real time encoding with low latency • Low cost and High performance • Able to secure space with compact and light weight design
• Make operators pay for less labor fee as offering quick and easy setup
Latency 800ms
Chroma Format 4:2:0 (8bit)
Resolutions up to 1080p
Options
DME-9624HMExcellent IP converter integrated- Much lower latency- More stable IP output
8
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Specification
Video Input
Analog Input Component , Composite
Level 1 Vp-p
Digital Input HDMI , SDI
Level 1000 mVp-p (HDMI) 800mVp-p (SDI)
Resolutions 480i29.97/30, 576i25, 720p50/59.94/60, 1080i25/29.97/30, 1080p25/29.97/30
SD Aspect Ratio 4:3, 16:9
Audio Input
Analog Input 1 Stereo(2channel)
Freq. Range 20Hz ~ 20KHz
Impedance 600 Ω
Connector Mini XLR
Digital Input AES-EBU, Embedded SDI/HDMI
Sampling Rate 32, 44.1, 48 KHz
Connector BNC (75Ω) / HDMI-19PIN
Optical Input SPDIF(5.1 Channel) (pass through).
Video Encoder
Encoding MPEG-2 HP@HL, MP@HL , MP@ML
H.264 HP@L4 , MP@L3
Encoding Rate MPEG-2 : 2~17.2 Mbps
H.264 : 0.5~17.2 Mbps
Chroma Format 4:2:0 (8bit)
PSNR 36dB
Bit Rate Mode CBR, VBR
Latency 800ms~
Audio Encoder
Sampling Rate 32, 44.1, 48KHz
Dolby Digital® AC-3(5.1CH) 128,192,256,384 Kbps
MPEG-1 Layer II 192,224,256,320,384 Kbps
MPEG-4 AAC-LC 32~384 Kbps
MPEG-4 HE-AAC v1 32~192 Kbps
MPEG-4 HE-AAC v2 32~96 Kbps
TS Input
Transport Stream ASI 1 Port
Connector BNC(75Ω)
Packet Format 188 Byte
Input Level 800mVp-p
TS Output
Transport Stream ASI 2 port
Connector BNC(75Ω)
TS Bitrate MPEG-2 : 3.4~19 Mbps
H.264 : 2.5~19 Mbps
Packet Format 188 Byte
IP TS Output
Output 1 Port
Connector RJ-45
Ethernet type 10/100 Base-T
Format UDP/IP, RTP/IP
IP Address Format Multicast, Unicast
TS Bitrate MPEG-2 : 3.4~19 Mbps
H.264 : 2.5~19 Mbps
TS Packet Rate 188, 204 Byte
Ethernet
Connector RJ-45
Interface Type 10/100Base-T
Protocols SNMP
General
Power Requirements AC 90~230V, 50/60Hz
Power Consumption Max. 100W
Weight 4kg
Operating Temperature -10~50°C
Dimension(W x H x D) 482 x 44 x 383 mm
Configuration
MPEG-2/4 AVC HD Encoder
DME-9624H
9
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
CASTWIN’s High-Definition encoder with the highestvideo quality and low latency. It shows outstandingperformance for inputting signal (Analog & Digital) tooutput as transport stream signal after compressingand encoding for suitable digital transmission withvarious supported formats. Moreover, it supports bothMPEG-2 and H.264 so that it make operator select theformat as they want.Also, it is very easy to control with Hi-class front VFD.
• Component, Composite, HDMI, HD/SD-SDI video inputs.• Low latency as 1,100ms• Digital and Analog audio inputs.• Selectable MPEG-2 or H.264 HD/SD real-time video encoding.
• Selectable outputting of 2xTransport stream (ASI) orUDP/IP transport stream.
• CBR outputs.• Dolby Digital (AC-3), MPEG-1 Layer II, AAC-LC audio encoding.
• User selectable resolution and bit rate.• Control and monitoring via web browser, front panel or SNMP
• Support Internally generated PSI /PSIP
Feature
• Easily adaptable to a wide range of professional application requiring high level performance functionality.
• Cost effective device with high resolution up to 1080i • Retain your viewers with high performance compression and flawless quality
• Offer user friendly interface with simple set-up and operation
• Compact and light weight design
Competitiveness
MPEG-2/4 AVC HD Encoder
DME-9524H
Latency 1100ms
Chroma Format 4:2:0
Resolutions up to 1080i
10
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Specification
Video Input
Analog Input Component , Composite
Level 1 Vp-p
Digital Input HDMI , SDI
Level 1000 mVp-p (HDMI) 800mVp-p (SDI)
Resolutions 480i, 480p, 576i, 576p, 720p, 1080i 25,29.97/30, 50, 59.94/60
SD Aspect Ratio 4:3, 16:9
Audio Input
Analog Input 1 Stereo(2channel)
Freq. Range 20Hz ~ 20KHz
Impedance 600 Ω
Connector PS/2
Digital Input Embedded SDI/HDMI
Sampling Rate 48 KHz
Connector BNC (75Ω) / HDMI-19PIN
Video Encoder
Encoding MPEG-2 MP@HL , MP@ML
H.264 HP@L4, MP@L3
Encoding Rate 3.5~30 Mbps
Chroma Format 4:2:0
PSNR 33dB
Bit Rate Mode CBR
Latency 1100ms~
Audio Encoder
Sampling Rate 48KHz
Dolby Digital® AC-3 128,192,256,384 Kbps
MPEG-1 Layer II 64,96,128,160,192,224,256,320,384 Kbps
MPEG-4 AAC-LC 64,96,128,160,192,224,256,320,384 Kbps
TS Output
Transport Stream ASI 2 port
Connector BNC(75Ω)
TS Bit Rate 3.5~30 Mbps
Packet Format 188 Byte
IP TS Output
Output 1 Port
Connector RJ-45
Ethernet type 100/1000 Base-T
Format UDP/IP
IP Address Format Unicast / Multicast
TS Packet Rate 188 Byte
Ethernet
Connector RJ-45
Interface Type 10/100Base-T
Protocols SNMP
General
Power Requirements AC 90~230V, 50/60Hz
Power Consumption Max. 100W
Weight 4 kg
Operating Temperature -10~50°C
Dimension(W x H x D) 482 x 44 x 383 mm
Configuration
MPEG-2/4 AVC HD Encoder
DME-9524H
11
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
DME-8624S8 is a Multi 8 channel Standard-Definition Encoder, as a newly released product of CASTWIN. It supports MPEG-2 and H.264 encoding and multiplexing with high video quality and low latency. Also, it is cost effective and makes the device widely used in varieties of digital distribution such as CATV/MATV/IPTV digital head-end.
• 8 Channel Encoding• Composite video input• MPEG-2 and H.264 real-time video encoding• Latency as 800 ms• CBR or VBR outputs• Dolby Digital(AC-3), MPEG-1 Layer II audio encoding• User Selectable resolution and bit rate• Control and monitoring via front panel• Excellent IP streaming output
Feature
• Saving your budget opportunities by 8 Channel Encoding
• Ensure critical content quality is preserved by using highest – performance compression and flawless picture quality
• Reduce the installing cost with simple set-up and Compact Size
• Able to Secure space with Compact and light weight design
Competitiveness
Multi 8 channel SD Encoder
DME-8624S8
8 Channel
MPEG-2 & H.264 SD Encoding
Latency 800ms
8 channel Multiplexing
12
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Specification
Video Input
Analog Input Composite
Resolutions 480i29.97, 576i25
Aspect Ratio 4:3, 16:9
Audio Input
Analog Input 1 Stereo
Freq. Range 20Hz ~ 20KHz
Impedance 600 Ω
Video Encoder
Encoding MPEG-2 MP@ML
H.264 MP@L3
Encoding Rate MPEG-2 : 2~12 Mbps
H.264 : 0.5~2.5 Mbps
Chroma Format 4:2:0
Bit Rate Mode CBR, VBR
Latency 800ms~
Audio Encoder
Sampling Rate 48KHz
Dolby Digital® AC-3 128,192,256,384 Kbps
MPEG-1 Layer II 64, 112~384Kbps
AAC-LC 32 ~ 384Kbps
HE-AAC v1 32 ~ 192Kbps
HE-AAC v2 32 ~ 96Kbps
Multi 8 channel SD Encoder
DME-8624S8
Configuration
TS Output
Transport Stream ASI 3 port
Connector BNC(75Ω)
TS Bit Rate 1~150 Mbps
Packet Format 188 Byte
IP TS Output
Output 1 Port
Connector RJ-45
Ethernet type 10/100/1000 Base-T
Stream Protocols UDP/IP, RTP/IP
IP Address Format Unicast / Multicast
Ethernet
Connector RJ-45
Interface Type 10/100Base-T
Protocols SNMP
General
Power Requirements AC 90~230V, 50/60Hz
Power Consumption Max. 100W
Weight 4 kg
Operating Temperature -10~50°C
Dimension(W x H x D) 482 x 44 x 483 mm
13
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
CASTWIN’s the standard definition encoder with thehighest video quality and low latency. It is perfectchoice for customers who are expecting the high-classproducts on video/audio quality. It shows outstandingperformance for inputting signal(Analog & Digital) tooutput as transport stream signal after compressingand encoding for suitable digital transmission withvarious supported formats. Moreover, it supports bothMPEG-2 and H.264 so that it make operator select theformat as they want. Also, it is very easy to control withHi-class front VFD.
• Component, Composite, HDMI, SD-SDI video inputs.• Digital, Analog and SDI embedded audio inputs.• Low latency as 800ms• Additional 1xASI input for supporting of insertion of externally generated PSIP into the transport stream.
• Video input Auto detection function.• Selectable MPEG-2 SD or H.264 SD real-time video encoding.
• Simultaneous outputting of 2xTransport stream (ASI) withUDP/IP or RTP/IP transport stream.
• CBR outputs.• Dolby Digital (AC-3), MPEG-1 Layer II, AAC-LC, HE-AAC audio encoding.
• Supports internally generated TVCT, CVCT, SDT, NIT• Control and monitoring via web browser, front panel, or SNMP
Feature
• Providing your viewers with the best performance compression and flawless picture quality
• Perfect option for broadcasting of sports, racing with Real time encoding with low latency
• Increase revenue opportunities by enabling additional services
• Reduce the cost of transmission as supporting Wide range of bit-rate control and advanced video coding techniques.
• Additional Cost reduction with Simple set-up and operation
Competitiveness
MPEG-2/4 AVC SD Encoder
DME-8624S
MPEG-2 & H.264 SD Encoding
Latency 800ms
Output ASI / IP Stream
14
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Specification
Video Input
Analog Input Component , Composite
Level 1 Vp-p
Digital Input HDMI , SDI
Level 1000 mVp-p (HDMI) 800mVp-p (SDI)
Resolutions 480i29.97/30, 576i,25
Aspect Ratio 4:3, 16:9
Audio Input
Analog Input 1 Stereo
Freq. Range 20Hz ~ 20KHz
Impedance 600 Ω
Connector Mini XLR
Digital Input AES-EBU, Embedded SDI/HDMI
Sampling Rate 32, 44.1, 48 KHz
Connector BNC (75Ω) / HDMI-19PIN
Video Encoder
Encoding MPEG-2 MP@ML
H.264 MP@L3
Encoding Rate MPEG-2 : 2~15 Mbps
H.264 : 0.5~15 Mbps
Chroma Format 4:2:0
Bit Rate Mode CBR, VBR
Latency 800ms~
Audio Encoder
Sampling Rate 32, 44.1, 48KHz
Dolby Digital® AC-3 128,192,256,384 Kbps
MPEG-1 Layer II 192,224,256,320,384 Kbps
MPEC-4 AAC-LC 32~384 Kbps
MPEG-4 HE-AAC v1 32~192 Kbps
MPEG-2 HE-AAC v2 32~96 Kbps
TS Input
Transport Stream ASI 1 Port
Connector BNC(75Ω)
Packet Format 188 Byte
Input Level 800mVp-p
TS Output
Transport Stream ASI 2 port
Connector BNC(75Ω)
TS Bit Rate MPEG-2 : 3.4~19 Mbps
H.264 : 2.5~19 Mbps
Packet Format 188 Byte
IP TS Output
Output 1 Port
Connector RJ-45
Ethernet type 10/100 Base-T
Format UDP/IP, RTP/IP
IP Address Format Multicast, Unicast
TS Bit Rate MPEG-2 : 3.4~19 Mbps
H.264 : 2.5~19 Mbps
TS Packet Rate 188 Byte
Ethernet
Connector RJ-45
Interface Type 10/100Base-T
Protocols SNMP
General
Power Requirements AC 90~230V, 50/60Hz
Power Consumption Max. 100W
Weight 4. Kg
Operating Temperature -10~50°C
Dimension(W x H x D) 482 x 44 x 383 mm
Configuration
MPEG-2/4 AVC SD Encoder
DME-8624S
15
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
As a representative decoder, the professional IRD is housed in a space-efficient chassis that receives various signals for decompressing. It is applied in many different kinds of networks, such as broadband fiber, cable, digital terrestrial, satellite and any other distribution network. It is very suitable for broadcast and professional applications requiring 4:2:2/4:2:0 decoding solution.
• MPEG-2/H.264 SD/HD 10bit/8bit 4:2:2/4:2:0 video decoding.• High quality SDI digital video• SD Aspect ratio conversion(4:3, 16:9)• 2 x ASI , RF, IP video inputs• Configured and controlled via front panel LCD.• HD-SDI outputs with embedded audio• HDMI output• Component Video output• Analog 4 stereo outputs. • SNMP control and monitoring • NTSC, PAL video formats• Resolution – up to 1080p 29.97• IP Stream output• Inputs – ATSC, ASI, QAM (Annex B)• 8ch AES/EBU audio input• Video Scaling Option (Up/Down/Cross)
Feature
• Providing your customers with the best performance of decoding and high quality
• Save your cost with various conversion • Able to secure space with Compact and light weight design
• Easy to set-up and control
Competitiveness
DVB-S/S2/S2X Receiving
Latency 100ms
Chroma Format 4:2:0 4:2:2
• DVB-CI• Input – DVB-S/S2/T/T2
Options
Integrated Receiver / Decoder
DMD-9724IRD
16
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
RF Input
Input Channel 1CH
Impedance 75Ω
Module Option DVB-S/S2/T/T2, DVB-C(Annex A, B, C), ATSC
IP Stream Input
No. of Port 1 port
Connector RJ-45
Format 100/1000BaseT
Max Input rate 188Mbps
ASI Input
DVB-ASI2 x BNC
SMPTE310M
Video Decoding
MPEG-2 SD Profile MP@ML(4:2:0) / 422@ML (4:2:2)
Max video rate 80 Mbps
Video format [email protected] fps/576i@25 fps
MPEG-2 HD Profile MP@HL(4:2:0) / 422@HL(4:2:2)
Max video rate 80 Mbps
Video format [email protected] fps/25 fps,
[email protected] fps/50 fps
H.264 SD Profile MP@L3(4:2:0) / 422HP@L3 (4:2:2)
Max video rate 80 Mbps
Video format [email protected] fps/576i@25 fps
H.264 HD Profile MP@L4 HP@L4 [email protected](4:2:0)
HIGH/HIGH10/[email protected] (4:2:2)
Max video rate 80 Mbps
50 Mbps CABAC, 85 Mbps CAVLC
Video format [email protected] fps/25 fps,
[email protected] fps/50 fps
Chroma Format 4:2:0 / 4:2:2 (10bit)
Bit Rate Mode CBR,VBR
Latency 100ms~
Audio Decoding
Audio Sampling rate 48kHz
MPEG-1 Layer 2 1.0/2.0 decode / pass-through
Dolby® Digital Pro 2.0//5.1 decode / consumer 2.0 decode
Plus 5.1/7.1 decode/5.1 decode &down-min to 2
2.0/5.1 pass-through//plus 5.1/7.1 pass-through
E 2.0/5.1/7.1 pass-through
AAC Audio AAC-LC 2.0/5.1 decode / HE-AAC v1 5.1 decode
HE-AAC v2 2.0 decode
AAC-LC 2.0/5.1 pass-through
Specification
Configuration
ASI Output
DVB-ASI 2 x BNC
Video Output
Analog Output Composite, Component
Digital Output HDMI x 1 , SDI x 2
Resolutions480i29.97, 576i25, 720p50/59.94, 1080p25/29.97
SD Aspect Ratio 4:3, 16:9
Audio Output
Analog Output 4 balanced stereo pairs
Freq. Range 20Hz ~ 20KHz
Impedance 600 Ω
Digital Output Embedded SDI/HDMI
Sampling Rate 48 KHz
IP Stream Output
Interface Type 10/100/1000 Base-T
Stream Protocols UDP/IP, RTP/IP
Broadcasting Multicast, Unicast
General
Power Requirements AC 90~230V, 50/60Hz
Power Consumption Max. 100W
Weight 4kg
Operating Temperature -10~50°C
Dimension(W x H x D) 482 x 44 x 383 mm
Power Requirements AC 90~230V, 50/60Hz
Integrated Receiver / Decoder
DMD-9724IRD
17
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
As a professional MPEG decoder, DMD-9724D is able to receive many different kinds of broadcasting signals and output as various digital interface signals. Moreover; it is able to decode MPEG-2 and H.264 in both 4:2:2 and 4:2:0.
• MPEG-2/H.264 4:2:0(8bit)/4:2:2(10bit) video decoding.• SD Aspect ratio conversion(4:3, 16:9)• Configured and controlled via front panel LCD.• HD-SDI outputs with embedded audio• Composite Video output• Analog stereo outputs.• SNMP control and monitoring• HDMI Output• NTSC, PAL video receiving
Feature
• Providing your customers with the best performance of decoding and high quality
• Able to secure space with Compact and light weight design
• Easy to set-up and control
Competitiveness
Input- DVB-ASI, IP StreamRF(8-VSB, QAM, DVB-T/T2, DVB-S) options
Output – HDMI, HD-SDI, Composite, Component(Option)
Options
MPEG-2 & H.264 Decoding
Latency 100ms
Chroma Format 4:2:0 4:2:2
MPEG Decoder
DMD-9724D
18
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
RF Input
Frequency Range 54~864MHz (8-VSB, QAM, DVB-T,/S)
Input Channel 1CH
Impedance 75Ω
Input Level -25~25dBmV
Return Loss ≥ 17 dB
Noise Figure VHF 7dB, UHF 9dB
TS Input
Transport Stream DVB-ASI 1 port
Packet Format 188 Byte
Connector BNC(75Ω)
TS Bit Rate MPEG-2 : 2.5~55 Mbps
H.264 : 2.5~55 Mbps
IP TS Input
IP Stream 1 port
Connector RJ-45
Ethernet type 10/100/1000 Base-T
Format UDP/IP, RTP/IP
IP Address Format Multicast, Unicast
TS Bit Rate MPEG-2 : 2.5~55 Mbps
H.264 : 2.5~55 Mbps
Video Decoder
Decoding MPEG-2 HP@HL, MP@HL , MP@ML
H.264 HP@L4, MP@L3
Bit Rate MPEG-2 : 2~50 Mbps
H.264 : 0.6~50 Mbps
Chroma Format 4:2:0, 4:2:2 (10bit)
Bit Rate Mode CBR,VBR
Latency 100ms~
Audio Decoder
Sampling Rate 32, 48KHz
Dolby Digital® AC-3(5.1CH) 128,192,256,384,448,512,576,640 Kbps
MPEG-1 Layer II 192,224,256,320,384 Kbps
MPEG-4 AAC-LC 32~384 Kbps
MPEG-4 HE-AAC v1 32~192 Kbps
MPEG-4 HE-AAC v2 32~96 Kbps
Specification
Configuration
Video Output
Analog Output Composite, Component(option)
Digital Output HDMI , SDI
Resolutions480i29.97, 576i25, 720p50/59.94, 1080i25/29.97, 1080p25/29.97
SD Aspect Ratio 4:3, 16:9
Audio Output
Analog Output 1 Stereo
Freq. Range 20Hz ~ 20KHz
Impedance 600 Ω
Digital Output Embedded SDI/HDMI (4stereo 8ch)
Sampling Rate 32, 48 KHz
Optical Input SPDIF(7.1Channel) Pass Through
Ethernet
Interface Type 10/100Base-T
Protocols SNMP
General
Power Requirements AC 90~230V, 50/60Hz
Power Consumption Max. 100W
Weight 4kg
Operating Temperature -10~50°C
Dimension(W x H x D) 482 x 44 x 383 mm
Power Requirements AC 90~230V, 50/60Hz
MPEG Decoder
DMD-9724D
19
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
As a representative model of CASTWIN, it is a new released evolutionary product. It is the professional and Hi-class product combining Ultra low delay HD Encoder and ATSC(8-VSB) Modulator. Moreover, it supportsboth MPEG-2 and H.264 so that operator can select and use the format. It is adopting high technology and very effective to make whole Digital Transmission System very compact and easy to controlwith front VFD.
• Advanced modulation integrated• Component, Composite, HDMI, HD/SD-SDI video inputs.• Ultra low latency as 150ms• Digital, Analog and SDI embedded audio(8ch) inputs.• 7.1 channel SPDIF audio optical input(pass through).• Additional 1xASI input for supporting of insertion of externally generated PSIP into the transport stream.
• Provides internally generated PSI and PSIP.• Selectable MPEG-2 or H.264 real-time video encoding.
• Simultaneous outputting of 1xRF and 1xTransport stream (ASI) with UDP/IP or RTP/IP transport stream.
• CBR or VBR outputs.• Dolby Digital (AC-3), MPEG-1 Layer II, AAC-LC, HE-AAC audio encoding.
• Supports EIA-708 Closed caption insertion via HD SDI(SMPTE 334).
• Control and monitoring via web browser, front panel, or SNMP.
• PCR Jitter : ≤ ± 200 ns• Excellent RF Output performance• Scaling function with integrated Advanced Scaler• Phase Noise VHF -105 dB@20KHz, UHF -103 dB@20KHz• Frequency : 54 ~ 1002MHz• MER After Equalizer : 42dB
Feature
• Retain your viewers with high performance compression and flawless quality
• Cost effective solution as a product combined modulator and up-converter
• Wide use in many projects with high compatibility supporting various formats
• Best choice for broadcasting of racing, sports via real time encoding with ultra low Latency as 150ms
• Reduce the cost of transmission as supporting wide range of bit-rate control and advanced video coding techniques.
• Able to secure space with compact size for installing
Competitiveness
MPEG HD Mediaplex
DMP-9724M
QAM(Annex A, B and C) ModulationDVB-T Modulation
Options
HD Encoder & Modulator
Latency 150ms
Chroma Format 4:2:0, 4:2:2 (10bit)
Resolutions HD 1080p
20
MPEG HD Mediaplex
DMP-9724M
MPEG HD Mediaplexwww.castwin.com Digital Products MPEG Mediaplexs
Specifications
ITEM CHARACTER
Video Input
Analog Input Component , CompositeDigital Input HDMI , HD-SDI
Level 1000 mVp-p (HDMI) / 800 mVp-p (HD-SDI)
Resolutions 480i29.97, 576i25, 720p50/59.94, 1080i25/29.97
Aspect Ratio 4:3, 16:9
Audio Input
Analog Input StereoFreq. Range 20 Hz ~ 20 KHzImpedance 600 Ω/ 20 KΩ
DigitalInput AES-EBU Embedded SDI/HDMI (4 Stereo 8 Channel)Sampling Rate 32,44.1,48 KHz
Optical Input SPDIF (7.1Channel) Pass Through
TS InputTransport Stream ASI 1 Port Packet Format 188 Byte
Video Encoder
Encoding MPEG-2 MP@HL , MP@ML
H.264 HP@L4, MP@L3
Encoding Rate MPEG-2 : 0.6~55 Mbps , H.264 : 0.6~50 MbpsChroma Format 4:2:0, 4:2:2 (8 bit/10 bit)PSNR 38 dBBit Rate Mode CBR,VBR
Latency 150 ms~
Audio Encoder
Sampling Rate 48 KHz
Dolby Digital® AC-3(5.1CH) 128,192,256,384,448,512,576,640 Kbps
MPEG-1 Layer II 64,96,112,128,160,192,224,256,320,384 Kbps
MPEG-4 AAC-LC 32~384 Kbps
MPEG-4 HE-AAC v1 32~192 Kbps
MPEG-4 HE-AAC v2 32~96 Kbps
RF Output
Frequency Range 50~1002 MHzImpedance 75 ΩOutput Level 50 ± 5 dBmVLevel Control Range 0 ~ -15 dBMER After Equalizer 42 dBMER Before Equalizer 37 dB
Phase Noise VHF -105 dB@20KHz, UHF -103 dB@20KHz
Adjacent Channel Carrier/Attenuation Characteristic ≤ -45 dB (Out of band)Spurious ≤ -63 dBReturn Loss ≥ 17 dBFrequency Response ± 0.5 dB Frequency Tolerance ± 2 ppmGroup Delay ± 20 ns PCR Jitter ≤ ± 200 ns
TS OutputTransport Stream ASI 1 portTS Bit Rate MPEG-2 : 2.5~55 Mbps , H.264 : 2.5~55 MbpsPacket Format 188 Byte
IP TS Output
(Option)
Output 1 PortConnector RJ-45 Ethernet type 10/100/1000 Base-TStream Protocol UDP/IP, RTP/IPBroadcasting Multicast, Unicast
TS Bit Rate MPEG-2 : 2.5~55 Mbps , H.264 : 2.5~55 Mbps
Ethernet
Connector RJ-45
Interface Type 10/100 Base-T
Protocols SNMP
General
Power Requirements AC 90~230 V, 50/60 HzPower Consumption Max. 100 WWeight 4 KgOperating Temperature -10~50 °CDimensions (W x H x D) 483 x 44 x 383 mm
Configuration
21
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
CASTWIN’s the professional and hi-class product combining low delay HD Encoder and ATSC(8-VSB) Modulator. It is adopting high technology and very effective to make whole Digital TransmissionSystem very compact and easy to control with front VFD. Moreover, it supports both MPEG-2 and H.264 so that operator can select and use the format.
• Component, Composite, HDMI, HD/SD-SDI video inputs.• Digital, Analog and SDI embedded audio inputs.• 5.1 channel SPDIF audio optical input(pass through).• Low latency as 800ms• Additional 1xASI input for supporting of insertion of externally generated PSIP into the transport stream.
• Selectable MPEG-2 HD or H.264 HD real-time video encoding.
• Simultaneous outputting of 1xRF and 1xTransport stream(ASI) with UDP/IP or RTP/IP transport stream
• CBR outputs.• Dolby Digital (AC-3), MPEG-1 Layer II, AAC-LC, HE-AAC audio encoding.
• Supports internally generated TVCT, CVCT, SDT, NIT• Scaling function with integrated Advanced Scaler• Supports EIA-708 Closed caption insertion via HDSDI(SMPTE 334).
• Control and monitoring via web browser, front panel, or SNMP
• Phase Noise VHF -105 dB@20KHz, UHF -103 dB@20KHz• Frequency : 54 ~ 1002MHz• Excellent RF Output performance
• Cost effective as integrated modulator and up-converter• Excellent option for operators who competitively pursue the best performing encoding device with high resolution
• Best option for Real time encoding with low latency• Able to Secure space with Compact and light weight design
• Make operators pay for less installing fee as offering Quick and easy setup
Competitiveness
MPEG HD Mediaplex
DMP-9624M
QAM(Annex A, B and C) ModulationDVB-T Modulation
Feature
Options
HD Encoder & Modulator
Latency 800ms
Chroma Format 4:2:0
Resolutions 1080p
22
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Specification
Video Input
Analog Input Component , Composite
Digital Input HDMI , SDI
Resolutions480i29.97/30, 576i25, 720p50/59.94/60, 1080i25/29.97/30 1080p25/29.97/30
Aspect Ratio 4:3, 16:9
Audio Input
Analog Input 1 Stereo(2channel)
Freq. Range 20Hz ~ 20KHz
Impedance 600 Ω
Digital Input AES-EBU Embedded SDI/HDMI
Sampling Rate 32,44.1,48 KHz
Optical Input SPDIF(5.1 Channel) (pass through
TS Input
Transport Stream ASI 1 Port
Packet Format 188 Byte
Video Encoder
Encoding MPEG-2 HP@HL, MP@HL , MP@ML
H.264 HP@L4 , MP@L3
Encoding Rate MPEG-2 : 2~17.2 Mbps
H.264 : 0.5~17.2 Mbps
Chroma Format 4:2:0
Bit Rate Mode CBR, VBR
Latency 800ms~
Audio Encoder
Sampling Rate 32, 44.1, 48KHz
Dolby Digital® AC-3(5.1CH) 128,192,256,384 Kbps
MPEG-1 Layer II 192,224,256,320,384 Kbps
MPEG-4 AAC-LC 32~384 Kbps
MPEG-4 HE-AAC v1 32~192 Kbps
MPEG-4 HE-AAC v2 32~96 Kbps
RF Output
Frequency Range 54~870 MHz
Impedance 75 Ω
Output Level 50 ± 5 dBmV
Level Control Range 0 ~ -15 dB
MER After Equalizer 42 dB
MER Before Equalizer 37 dB
Phase NoiseVHF -105 dB@20KHz
UHF -103 dB@20KHz
Adjacent Channel Carrier/Attenuation Characteristic
≤ -45 dB (Out of band)
Spurious ≤ -63 dB
Return Loss ≥ 17 dB
Frequency Response ± 0.5 dB
Frequency Tolerance ± 2 ppm
Group Delay ± 20 ns
PCR Jitter ≤ ± 200 ns
TS Output
Transport Stream ASI 1 port
TS Bit Rate MPEG-2 : 3.4~19 Mbps
H.264: 2.5~19 Mbps
Packet Format 188 Byte
Ethernet
Interface Type 10/100Base-T
Protocols SNMP
IP TS Output
Output 1 Port
Ethernet type 10/100 Base-T
Format UDP/IP, RTP/IP
IP Address Format Multicast, Unicast
TS Bit Rate MPEG-2 : 3.4~19 Mbps
H.264: 2.5~19 Mbps
TS Packet Rate 188 Byte
General
Power Requirements AC 90~230V, 50/60Hz
Power Consumption Max. 100W
Weight 4kg
Operating Temperature -10~50°C
Dimension(W x H x D) 482 x 44 x 383 mm
Configuration
MPEG HD Mediaplex
DMP-9624M
23
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
CASTWIN’s professional and hi-class product combining low delay HD Encoder and ATSC(8-VSB) Modulator.It is adopting high technology and very effective to make whole Digital Transmission System very compact and easy to control with front VFD.
• Component, Composite, HDMI, HD/SD-SDI video inputs• Digital and Analog audio inputs• Low latency as 1,100ms• Selectable MPEG-2 HD or H.264 real-time video encoding.
• CBR outputs.• Dolby Digital (AC-3), MPEG-1 Layer II, AAC-LC audio encoding.
• User selectable resolution and bit-rate, output frequency.• Control and monitoring via web browser, front panel.• PCR Jitter : ≤ ± 200 ns• Group Delay as ± 20 ns• Phase Noise VHF -105 dB@20KHz, UHF -103 dB@20KHz• Frequency : 54~ 1002MHz• Excellent RF Output performance• MER After Equalizer : 42dB• Support Internally generated PSI /PSIP
Feature
• Easily adaptable to a wide range of professional application requiring high level performance functionality.
• Retain your viewers with high performance compression and flawless quality
• Save installing fee with Simple set-up and operation• Retain your viewers with high quality and low attenuation
Competitiveness
MPEG HD Mediaplex
DMP-9524M
QAM(Annex A, B and C) ModulationDVB-T Modulation
Options
HD Encoder & Modulator
Latency 1100ms
Chroma Format 4:2:0
24
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Specification
Video Input
Analog Input Component , Composite
Digital Input HDMI , SDI
Resolutions480i, 480p, 576i, 576p,720p,
1080i 25,29.97/30,50,59.94/60
Aspect Ratio 4:3, 16:9
Audio Input
Analog Input 1 Stereo(2channel)
Freq. Range 20Hz ~ 20KHz
Impedance 600 Ω/ 20KΩ
Digital Input Embedded SDI/HDMI
Sampling Rate 48 KHz
Video Encoder
Encoding MPEG-2 MP@HL , MP@ML
H.264 HP@L4, MP@L3
Encoding Rate 3.5~30 Mbps
Chroma Format 4:2:0
Bit Rate Mode CBR
Latency 1,100ms~
Audio Encoder
Sampling Rate 48KHz
Dolby Digital® AC-3 128,192,256,384 Kbps
MPEG-1 Layer II 64,96,128,160,192,224,256,320,384 Kbps
AAC-LC (H.264 Only) 64,96,128,160,192,224,256,320,384 Kbps
TS Output
Transport Stream ASI 1 port
TS Bit Rate 3.5~30 Mbps
Packet Format 188 Byte
RF Output
Frequency Range 54~870 MHz
Impedance 75 Ω
Output Level 50 ± 5 dBmV
Level Control Range 0 ~ -15 dB
MER After Equalizer ≥ 42 dB
MER Before Equalizer ≥ 37 dB
Phase NoiseVHF -105 dB@20KHz
UHF -103 dB@20KHz
Adjacent Channel Carrier/Attenuation Characteristic
≤ -45 dB (Out of band)
Spurious ≤ -63 dB
Return Loss ≥ 17 dB
Frequency Response ± 0.5 dB
Frequency Tolerance ± 2 ppm
Group Delay ± 20 ns
PCR Jitter ≤ ± 200 ns
Ethernet
Interface Type 10/100Base-T
Protocols SNMP
IP TS Output
Output 1 Port
Ethernet type 10/100 Base-T
Format UDP/IP
IP Address Format Unicast / Multicast
TS Packet Rate 188 Byte
General
Power Requirements AC 90~230V, 50/60Hz
Power Consumption Max. 100W
Weight 4kg
Operating Temperature -10~50°C
Dimension(W x H x D) 482 x 44 x 383 mm
Configuration
MPEG HD Mediaplex
DMP-9524M
25
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
CASTWIN’s high-performance ISDB-Tb multiplexer DMX-1908ST is and ideal & cost-effective solution for ISDB-T/Tb transmitter/translator manufacturers, system integrators and broadcaster who want their own ISDB-Tb multiplexer in any region or country where is adopting ISDB-Tb
The DMX-1908ST : ISDB-Tb multiplexer supports SFN with 1PPS & 10MHz input. It provides various re-multiplexing function such as PCR correction, PID re-mapping, and PSI information editing & generating
Transmitter/Translator manufacturers can provide package solution which combines their own ISDB-Tb transmitter/translator and DMX-1908ST : ISDB-Tb together for broadcasters. It will be your strong competitiveness comparing with other competitors who has only exciter or translator. Of course, DMX-1908ST : ISDB-Tb will be a perfect solution for broadcasters who want to find more cost-effective Head-end multiplexer
Additionally, DMX-1908ST supports various global DTV/ mobile TV standards, including ISDB-T, ATSC, ATSC-M/H, CMMB, DVB-T2, and SFCMM on single board.With its FPGA based H/W architecture, user can upgrade new DTV/Mobile TV standards on DMX-1908ST board easily.
• Fully complying with ISDB-T & ISDB-Tb standards• Compact & Cost-effective ISDB-Tb Multiplexer• External 10MHz & 1PP input (SFN supports)• PSI/SI Information editing & generating• PCR Correction and PID re-mapping• IIP Packet editing and inserting• Interoperability proven with major ISDB-Tb Transmitters
Feature
• supports SFN with 1PPS & 10Mhz input• provides various re-multiplexing functions such as
PCR correction, PID re-mapping,, and PSI/SI information editing & generating
• supports various global DTV/Mobile TV Standards,including ISDB-T, ATSC, ATSC-M/H, CMMB, DVB-T2 and SFCMM on single board
Competitiveness
ISDB-T Multiplexer
DMX-1908ST
ISDB-T & ISDB-Tb
Options
Professional ISDB-T / ISDB-Tb
Multiplexer
26
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Specification
Input
DVB-ASI input 8EA
GPS 10MHz Reference Clock 1EA
GPS 1PPS Signal 1EA
Multiplexing & Re-multiplexing
TS Multiplexer & Re-multiplexer
PCR Correction
256 PID Mapping for Each Port (TBD)
Automatically Generated PSI/SI Table (TBD)
Modulation Parameter
Mode: Mode1 (2K), Mode2 (4K), Mode3 (8K)
Mode
Guard Interval 1/4 1/8, 1/16, 1/32
Coding Rate 1/4 2/3, ¾, 5/6, 7/8
Constellation DQPSK, QPSK, 16QAM, 64QAM
Layer A, A+B, A+B+C
Bandwidth 6MHz, 7MHz, 8MHz
SFN Parameter
Maximum Time Delay 0ms ~ 1,000ms
Off set -1,000ms ~ +1,000ms
Device ID 0 ~ 30
ISDB-T Multiplexer
DMX-1908ST
Output
DVB-ASI Output 2EA
10MHz Loop Out 1EA
User Control
WEB/Silverlight based Easy GUI via Web
Compatible with Any Web-Browsers
General
Modular Type
Dimension 300 x 180
Weight 0.46Kg
Rack Server Type
Power Requirements AC 85 ~ 286V
Power Consumption 24W
Weight 4.5Kg
Format 1RU rackmount, width 19”
Dimension(W x H x D) 483 x 1RU x 300 mm
27
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
CASTWIN’s High-Performance DVB-T2 Gateway,DMX-1908T2 DVB/T2 Gateway is an ideal & cost-effective solution for DVB-T2 transmitter/translator manufacturers and system integrators who want their own product range in any region or country where is adopting DVB-T2.
The DMX-1908T2 DVB-T2 Gateway encapsulates one or several MPEG-2 TS from DVB-T2 multiplexers into DVB-T2 Base Band frames, and outputs the resulting DVB-T2 multiplex using the DVB-T2 MI (Modular Interface) protocol via ASI and IP. The DVB-T2 MI controls the modular parameters and provides the accurate timing and rate control required in a SFN network. It also supports MISO broadcasting to reinforce SFN performance and management of 8 PLP (Physical Layer Pipes) without any option.
• DVB-T2 MI EncapsulationEncapsulation into Base Band frames Full support of BB frame modes
• DVB-T2 MI interface to the DVB-T2 TransmittersL1 Signaling & SFN time stamp insertion.
• Individual Addressing of DVB-T2 modulatorsMISO (Multi Input Single Output) supportPeak to Average Power Ratio (PAPR) parameters
• Integrated SFN adopterSingle & Multi PLP operationMapping of input TS into individual PLPs
• T2-MI OutputsGeneration of T2-MI packets
Feature
DVB-T2 Gateway
DMX-1908T2
Professional DVB-T2 Gateway
28
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Specification
Input
DVB-ASI input 8EA
Ethernet Port (TBD) 2EA
GPS 10MHz Reference Clock 1EA
GPS 1PPS Signal 1EA
Output
DVB-ASI Output 2EA
10MHz Loop Out 1EA
TS Encapsulation in T2-M1 Packets
Single and Multi PLP
NPD (Null Packet Deletion)
ISSY (Input Stream Synchronization) Support
Normal / High Efficiency Mode
Common (L1-Signaling) Parameter
Bandwidth 1.7MHz, 5MHz, 6MHz, 7MHz, 8MHz, 10MHz
FFT 1K, 2K, 4K, 8K, 16K, 32K
Guard Interval 1/4 , 1/8, 1/16, 1/32, 1/128, 19/128, 19/256
Pilot Pattern PP1 ~ PP8
Preamble Format MISO / SISO
Function to Modify DVB-T2 L1 - Signaling
DVB-T2 Gateway
DMX-1908T2
SFN Parameter
Maximum Time delays 0ms ~ 1,000ms
Off Set -1,000 ~ 1,000ms
1PPS Time Reference Input
TS and System Monitoring
Min/Max/Current Bitrate monitoring of Packets for Each Services
Easy-to-use Web based GUI
Monitoring ALL Input / Output and System
Full SNMPv2 support
General
Modular Type
Dimension 300 x 180
Weight 0.46Kg
Rack Server Type
Power Requirements AC 85 ~ 286V
Power Consumption 24W
Weight 4.5Kg
Format 1RU rackmount, width 19”
Dimension(W x H x D) 483 x 1RU x 300 mm
29
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
CASTWIN’s NMS offers optimized solution which is very adaptable for various devices. It provides user friendly interface and convenience in order to integrative manage the number of devices easily. Also, it offers Fast-analyzing function to respond for any occurred problem immediately. It uses convenient managing tool set so that it let users manage for CASTWINs. Additionally, it offers warning and notice solution for various cases.
• Realize high advanced network monitoring• Monitoring operation status• Convenient Tab for searching• Sensing for any occurred problem from devices• Management of error, function, solution• Management of data upon occurred error, fluctuation • Monitoring entire network of CASTWIN• Prompt access via Web GUI• Perfect and fast control• Standard up-grade & maintenance
Feature
• CASTWIN’s NMS offers optimized solution to prevent from inconvenience with un-necessary function, inaccurate data, bug etc after set-up.
• CASTWIN’s NMS is much easier to use and install for users compared to other existing NMS.
• Cost effective solution by easy installation and reduction of labor cost
• Enable users to better manage the network and quality of service combined with lower operational costs
Competitiveness
Management System
NMS
30
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
AS a 8-VSB modulator, it is a professional performing product based on the 8-VSB(ATSC) modulation. It shows superior quality to modulate MPEG transport stream as DVB-ASI signal to 8-VSB(ATSC) and output as suitable frequency band for digital broadcasting transmission. Also, it is very easy to control with high class front VFD.
• ASI input transport stream• Excellent RF output• Supports 8-VSB(ATSC) modulation• User adjustable output level and frequency• Front panel control• PCR Jitter: ≤ ± 200 ns• Group Delay as ± 20 ns • Phase Noise VHF -105 dB@20KHz, UHF -103 dB@20KHz• Frequency: 54 ~ 1002MHz • Output Level: 55±5 dBmV• Spurious: ≤ -63dB• MER After Equalizer: 42dB• Highly Advanced fine-tuning
Feature
• Retain your viewer with optimized modulator for ATSC(8-VSB)
• Excellent coding as ITU-T(J.83) Annex D• Cost reduction for installing with simple set-up and operation • Stable output with Hybrid AMP integrated• Secure more space with compact and light weight design
Competitiveness
8-VSB Modulator
DVM-1903ML
Specification
Configuration
Digital Input
Transport Stream DVB-ASIConnector BNC (75Ω)Coding ITU-T (J.83) Annex DBit Rate 19.393 MbpsPacket Format 188ByteSymbol Rate 10.762 Msymbol/sModulation 8-VSB
RF Output
Frequency Range 54~1002MHz
Impedance 75Ω
Output Level 50 ± 5 dBmV
Level Control Range 0~-15dB
Bandwidth 6MHz
MER After Equalizer ≥ 42 dB
MER Before Equalizer ≥ 37 dB
Phase Noise VHF -105 dB@20KHz
UHF -103 dB@20KHzAdjacent Channel Carrier Attenuation Characteristic ≥ 45 dB (Out-of-band)
Spurious ≤-63 dB
Return Loss ≥ 17 dB
Group Delay ± 20ns
Frequency Response ± 0.5dB
Frequency Tolerance ± 2ppm
PCR Jitter ≤ ± 200 ns
General
Power Requirements AC 90~230V, 50/60HzPower Consumption 13WWeight 3KgDimensions 482 x 44 x 383 mm
31
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
AS a QAM modulator, it shows professional performance for received transport stream signal to output as frequency band for suitable CATV band transmission. It is also easy to select frequency band via front control panel.
• ASI input transport stream• Excellent RF output• Supports QAM modulation• Supports PCR re-stamping function• User adjustable output level and frequency• Front panel control• QAM Modulation setting (64, 256QAM)• PCR Jitter: ≤ ± 200 ns• Group Delay as ± 20 ns • MER After Equalizer: 42dB• Phase Noise: VHF -105 dB@20KHz, UHF -103 dB@20KHz• Frequency: 54 ~ 1002MHz• Output Level: 55±5 dBmV• Spurious: ≤ -63dB
Feature
• Hi-dense modulating for QAM(Annex A, B and C) • Advanced coding as ITU-T(J.83) Annex A, B and C • Cost effective with simple set-up and operation • Hybrid AMP integrated
Competitiveness
Specification
Configuration
Digital Input
Transport Stream ASIConnector BNC (75Ω)Coding ITU-T (J.83) Annex A, B and CBit Rate 1~52 MbpsPacket Format 188 ByteSymbol Rate 1~7MbpsModulation 64,256 QAM
RF Output
Frequency Range 54~1002MHzImpedance 75Ω
Output Level 50 ± 5 dBmV
Level Control Range 0~-15dB
Bandwidth 6MHz : Annex B and C
8MHz : Annex A
MER After Equalizer ≥42 Db
MER Before Equalizer ≥37 dB
Phase Noise VHF -105 dB@20KHz
UHF -103 dB@20KHzAdjacent Channel Carrier Attenuation Characteristic ≥ 45 dB (Out-of-band)
Spurious ≤-63 dB
Return Loss ≥15 dB
Group Delay ±2 0ns
Frequency Response ± 0.5dB
Frequency Tolerance ±2ppm
PCR Jitter ≤ ± 200 ns
General
Power Requirements AC 90~230V, 50/60HzPower Consumption 13WWeight 3KgDimensions 482 x 44 x 383 mm
QAM Modulator
DQM-1903ML
32
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
As a NEW released CASTWIN products, It is converts IP to DVB-ASI , or DVB-ASI to IP with GigE Interface. The IP Converter is a cost effective alternative to above both systems, as it connects digital video equipment to easy management. Also it is very easy to control with Hi-class front VFD.
• Received MPEG-2 or H.264 transport streams over Ethernet-based IP networks and converts them to DVB-ASI.
• Received TS as ASI format and output to IP network• SMPTE-2022• Supports IP de-encapsulation and 2D FEC decoding
according to SMPTE 2022-1/2• Interchangeable plugs power adaptor clips US and EU type.
(UK, AUS types are optional)• Inputs : 1 x DVB-ASI and 1 x GigE IP • Outputs: 1 x DVB-ASI and 1 x IP out • Support 7 IP from 1 TS• Support 270Mbpt/s bitrate of DVB-ASI • Support 1ms Latency of ASI to IP • Support IPv4 • Support Unicast and Multicast IP addressing
Feature
Specification
IPASI Converter
DIC-500
Applications• Autonomous IP to ASI gateway• With DIC-500 Tunneling of ASI signals over LAN, WANor the internet
• Remote ASI output adapter for server based datainserters, stream servers, multiplexers and similarsystems
KEY ATTRIBUTES
GigE Port
Physical Layer IEEE 802.3aData rate 10/100/1000Connector RJ-45
ASI Port
Physical Layer DVB-ASI (coax)Connector 75Ω BNC(2x)Ts bitrate < 214 Mbit/s
Transport
TS per IP 1~7Encapsulation UDP or RTPFEC SMPTE 2022
IP to ASI latency 10msJitter tolerance range 1~120ms
CONTROL
IP-address assignment DHCP or static
Multicast support IGMP v2
Front panel control
GENERAL
Power Requirements DC 5V 2A
Weight 0.5kg
Dimensions(W x L x H) 148 x 170 x 35 mm
33
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
As a NEW released CASTWIN products, it is high performance Cross Converter which converts the signal from various inputting formats as HDMI, 3G/HD/SD-SDI, component, composite to various formats. Also, it is integrated with video processor which supports Selectable resolution and improvement for Image enhancing, Phase Noise, control of colors & Gamma.
• Inputs : HDMI, 3G/HD/SD-SDI, Component, Composite. • Outputs : HDMI, 3G/HD/SD-SDI, • Selectable Output Resolution: 480i, 576i, 720p, 1080i, 1080p• HDMI, 3G/HD/SD-SDI supports• 2 Channel Mini XLR audio inputs interface• AES/EBU(BNC), Analog L/R audio input interface• HDMI V1.4 standards support• Upload and configuration via USB2.0• HDMI/SDI Dual Output
Feature
Specification
Multi Digital Scaler
DSR-1000
Competitiveness
• Compact Size and Light Weight• Low Cost & High performance• Simply easy to use • Fully compatible with all your SD and HD device.
Scalar
Max Input Video Resolution 1920x1080@60pMax Output Video Resolution 1920x1080@60p
Frame-rate-conversion
480i(29.9/30), 576i(25), 720p(50/59.94/60)
1080i(25/29.97/30)
1080p(23.98/24/25/29.97/30/50/59.94/60)
Video Input
Analog Input Composite, Component
Digital Input HDMI, 3G/HD/SD-SDI
Resolutions
480i(29.9/30), 576i(25), 720p(50/59.94/60)
1080i(25/29.97/30)
1080p(23.98/24/25/29.97/30/50/59.94/60)
Impedance 75Ω
Aspect Ratio 4:3, 16:9
Analog Composite, Component
Digital HDMI,SD/SDI,3Gb/s SDI
Audio Input
Analog Input Stereo
Frequency Range 20Hz~20KHz
Impedance 600Ω
Connector Mini XLR
Digital Input ASE/EBU, Embedded HDMI/SDI
Sampling Rate 32, 44.1 & 48 KHz
Connector HDMI-19PIN,BNC(75Ω)
SDI
Compliance SMPTE-259/272/274/292/296/299/424/425
Video Rates 4:2:2, 4:4:4
Data Rates SD-SDI : 270Mbps
HD-SDI : 1.5Gb/s & 3Gb/s
Color Space YUV
HDMI
Color Precision 4:2:2, 4:4:4
Version V1.4 Standard
Video Output
Digital Output HDMI, 3G/HD/SD-SDI
Impedance 75 Ω
Aspect Ratio 4:3, 16:9
General
Power Requirements DC 12V 1A
Power Consumption 13W
Weight 0.74Kg
Dimensions 270x170x35
34
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
As a NEW released CASTWIN products, it is high performance Cross Converter which converts the signal from various inputting formats as HDMI, 3G/HD/SD-SDI, component, composite to various formats. Also, it is integrated with video processor which supports Selectable resolution and improvement for Image enhancing, Phase Noise, control of colors & Gamma.
• Inputs : HDMI• Outputs : 3G/HD/SD-SDI• Selectable Output Resolution: 480i, 576i, 720p, 1080i, 1080p• HDMI v1.4 standards • Upload and configuration via USB2.0
Feature
Specification
HDMI to SDI Scaler
DSR-500
Competitiveness
• Compact Size and Light Weight• Low Cost & High performance• Simply easy to use • Fully compatible with all your SD and HD device.
Scaler
Max Input Video Resolution 1920x1080@60pMax Output Video Resolution 1920x1080@60p
Frame-rate-conversion480i(29.9/30), 576i(25), 720p(50/59.94/60)
1080i(25/29.97/30)
1080p(23.98/24/25/29.97/30/50/59.94/60)
Video Input
Digital Input HDMI
Resolutions
480i(29.9/30), 576i(25), 720p(50/59.94/60)
1080i(25/29.97/30)
1080p(23.98/24/25/29.97/30/50/59.94/60)
Aspect Ratio 4:3, 16:9
Color Precision 4:2:2, 4:4:4
HDMI Version V1.4 Standard
Audio Input
Digital Input Embedded HDMI
Sampling Rate 32, 44.1 & 48 KHz
Connector HDMI-19PIN
Video Output
Digital Output 3G/HD/SD-SDI
Impedance 75 Ω
Aspect Ratio 4:3, 16:9
ComplianceSMPTE-259/272/274/292/296/299/424/425
Data Rates SD-SDI : 270Mbps
HD-SDI : 1.5Gb/s & 3Gb/s
Video Rates 4:2:2, 4:4:4
Color Space YUV
General
Power Requirements DC 12V 1A
Power Consumption 13W
Weight 0.74Kg
Dimensions 270x170x35
DSR-500
HDMI to SDI Scaler
35
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
As a NEW released CASTWIN products, It is the highly advanced multi media converter including SD/HD switching function. It shows best performance to convert from HDMI or SDI or Component or Composite to HDMI and SDI video out simultaneously with embedded HDMI and SDI audio.
• Inputs : HDMI, SDI, Component, Composite• Outputs : HDMI, 3G/HD/SD-SDI, • AES/EBU(BNC) , Analog L/R audio input interface• HDMI, 3G/HD/SD-SDI supports• HDMI v1.4 standards support• HDMI/SDI Dual output• 2Ch Mini XLR Audio inputs interface• Upload and Configuration via USB2.0
Feature
Specification
Multi Media Converter
MMC-1000
MMC-1000
Competitiveness
• Compact size and light weight• Simply easy to use • Fully compatible with all your SD and HD device.
Video Input
Analog Input Composite, Component
Digital Input HDMI, 3G/HD/SD-SDI
Resolutions
480i(29.9/30), 576i(25)720p(50/59.94/60) 1080i(25/29.97/30) 1080p(23.98/24/25/29.97/30/50/59.94/60)
Impedance 75Ω
Aspect Ratio 4:3, 16:9
Audio Input
Analog Input Stereo
Frequency Range 20Hz~20KHz
Impedance 600Ω
Connector Mini XLR
Digital Input AES/EBU, Embedded HDMI/SDI
Sampling Rate 32, 44.1 & 48 KHz
Connector HDMI-19PIN,BNC(75Ω)
SDI
Compliance SMPTE-259/272/274/292/296/299/424/425
Data Rates SD-SDI : 270Mbps
HD-SDI : 1.5Gb/s & 3Gb/s
Video Rates 4:2:2, 4:4:4
Color Space YUV
HDMI
Color Precision 4:2:2, 4:4:4
Version V1.4 Standard
Video Output
Digital Output HDMI, 3G/HD/SD-SDI
Impedance 75 Ω
Aspect Ratio 4:3, 16:9
General
Power Requirements DC 12V 1A
Power Consumption 13W
Weight 0.74Kg
Dimensions 270x170x35
36
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
It is highly performing Analog to HD/SD-SDI converter for converting from component or composite analog video signal to SDI with stereo audio.
• Input : Component, Composite, Analog L/R• Output : HD/SD-SDI• Upload and configuration via USB2.0
Feature
Specification
Media Converter
ATS-500
Competitiveness
• Compact size and light weight• Simply easy to use• Fully compatible with all your SD and HD devices.
Video Input
Analog Input Composite, Component
Resolutions
480i(29.9/30)
576i(25)
720p(50/59.94/60)
1080i(25/29.97/30)
Impedance 75Ω
Aspect Ratio 4:3, 16:9
Audio Input
Analog Input Stereo
Frequency Range 20Hz~20KHz
Impedance 600Ω
Connector 6.35mm Phone Jack
Video Output
Digital Output HD/SD-SDI
Impedance 75 Ω
Aspect Ratio 4:3, 16:9
Compliance SMPTE-259/272/274/292/296/299
Data Rates SD-SDI : 270Mbps
HD-SDI : 1.5Gb/s
Video Rates 4:2:2, 4:4:4
Color Space YUV
General
Power Requirements DC 12V 1A
Weight 0.22Kg
Dimensions 110x90x28 mm
ATS-500
Analog to SDI
37
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com
Introduction
It is superior to convert from SDI to HDMI video out with embedded HDMI audio
• Input : Embedded 3G/HD/SD-SDI• Output : HDMI• HDMI V1.4 standards • SDI loop through output • Upload and configuration via USB2.0
Feature
Specification
Media Converters
STH-500 / HTS-500
Video Input
Digital Input 3G/HD/SD-SDI
Resolutions
480i(29.9/30), 576i(25), 720p(50/59.94/60)
1080i(25/29.97/30)
1080p(23.98/24/25/29.97/30/50/59.94/60)
Impedance 75Ω
Aspect Ratio 4:3, 16:9
Audio Input
Digital Input Embedded SDI
Sampling Rate 48KHz
Connector BNC (75Ω)
SDICompliance SMPTE-259/272/274/292/296/299/424/425
Data Rates SD-SDI : 270Mbps
HD-SDI : 1.5Gb/s & 3Gb/s
Video Rates 4:2:2, 4:4:4
Color Space YUV
HDMIColor Precision 4:2:2, 4:4:4
Version V1.4 Standard
Video Output
Digital Output HDMI
Aspect Ratio 4:3, 16:9
General
Power Requirements DC 12V 1A
Weight 0.22Kg
Dimensions 110x90x28 mm
STH-500
Introduction
It is superior to convert from HDMI to SDI video out with embedded SDI audio.
• Input : HDMI• Output: 3G/HD/SD-SDI• HDMI V1.4 standards • Upload and configuration via USB2.0
Feature
SpecificationVideo Input
Digital Input HDMI
Resolutions
480i(29.9/30), 576i(25), 720p(50/59.94/60)
1080i(25/29.97/30)
1080p(23.98/24/25/29.97/30/50/59.94/60)
Aspect Ratio 4:3, 16:9
Audio Input
Digital Input Embedded HDMI
Sampling Rate 32,44.1,48KHz
Connector HDMI-19PIN
SDICompliance SMPTE-259/272/274/292/296/299/424/425
Data Rates SD-SDI : 270Mbps
HD-SDI : 1.5Gb/s & 3Gb/s
Video Rates 4:2:2, 4:4:4
Color Space YUV
HDMIColor Precision 4:2:2, 4:4:4
Version V1.4 Standard
Video Output
Digital Output 3G/HD/SD-SDI
Impedance 75 Ω
Aspect Ratio 4:3, 16:9
General
Power Requirements DC 12V 1A
Weight 0.22Kg
Dimensions 110x90x28 mm
HTS-500
SDI to HDMI HDMI to SDI
38
#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]
Head Office / Laboratory www.castwin.com