Setting NMEA Output on Trimble Juno Series May 22, 2013

P. O. Box 31, Jerome, ID 83338 Ph: (208) 324-8006 Fax: (208) 324-8015 www.elecdata.com support@elecdata.com

The Electronic Data Solutions logo is a recognized trademark of Field Data Solutions, Inc. All other trademarks are registered or recognized trademarks of their respective owners. All rights reserved. Copyright 5/2013.

The Trimble Juno series is capable of standard NMEA output. However, the receiver may have the SiRF protocol enabled by default. Mapping programs, such as ESRI ArcPad, will not be able to communicate with the Juno receiver until NMEA output is configured. Installing GPS Controller All options are enabled using the GPS Controller program, available for download from Trimbles Support Website. To install this program on your mobile device, follow these steps: 1. Download the program from http://www.trimble.com/support_trl.asp?pt=GPS Control-ler&Nav=Collection-32053 2. Connect your Juno using Microsoft ActiveSync technology or Windows Mobile Device Center. 3. Run the program downloaded in Step 1. Set Configuration Options All configuration options are set by first connecting to the receiver in GPS Controller, setting op-tions, then disconnecting from the receiver in GPS Controller. 1. Start GPS Controller by going to Start > Programs. The program will attempt to connect to the GPS receiver on COM 7. 2. Tap the drop-down arrow in the upper left-hand corner and select Setup. 3. Tap GPS Settings. 4. Set GPS Receiver Port to COM 7

The Electronic Data Solutions logo is a recognized trademark of Field Data Solutions, Inc. All other trademarks are registered or recognized trademarks of their respective owners. All rights reserved. Copyright 5/2013.

5. Scroll down and change NMEA Output to On. Tap the wrench that appears next to NMEA Out-put to configure which NMEA sentences to have the receiver output. Tap OK to save this change. A message appears stating that The NMEA output settings will be applied on discon-nect. Note-This does NOT occur if you simply exit GPS Controller. 6. Tap Options > Disconnect from GPS to apply the settings changes. 7. When prompted, tap Yes to disconnect. NMEA output is now set.

2

/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 300 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Bicubic /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Bicubic /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile () /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False

/CreateJDFFile false /Description > /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ > /FormElements false /GenerateStructure false /IncludeBookmarks false /IncludeHyperlinks false /IncludeInteractive false /IncludeLayers false /IncludeProfiles false /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /DocumentCMYK /PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling /UseDocumentProfile /UseDocumentBleed false >> ]>> setdistillerparams> setpagedevice