New Tube Fitting Mini Series C D S I - Trikanditrikandi.com/media/PDF/Pisco Tube Fitting Mini...

27

Fitting

Control

Valve

Vacuum

Actuator

Tube

Plarailchain

Robot Parts

Tube Fitting Mini Series

• The ultra-small quick-fitting joint is used in pneumatic piping.• This quick-fitting joint is 40% smaller than the standard type Tube Fitting.• The eliptical, ultra-small release ring facilitates connecting and disconnecting the

tube.

1.8mm tube size• This is first ever developed quick-fitting joint for ø1.8mm tube size.• It is 20% smaller than ø4mm tube size mini-type Fitting.

Clean-room Package• Non-spattering lubrication prevents spattering in clean-room. (Order Production)

Comparison with Standard Type

Characteristics

TypeFluid mediumMax. operating pressureMax. vacuumOperating temp. range

Specifi cationsStandard Clean-room Package

Air150psi (1MPa)

-29.5in. Hg (-100kPa)32~140°F (0~60°C)

No(1)(2)(3)(4)(5)(6)(7)(8)

ConstructionParts

Resin bodyLock clawsGuide ring Release ringTubeElastic sleeveO-ringMetallic body

Standard pkgPBTstainless steelnickel-plated brassPOMurethane or nylonNBRNBRnickel-plated brass

Clean-room pkgPBTstainless steelnickel-plated brassPOMclean-room readyNBRNBRnickel-plated brass

(1)

(2)

(4) (5)

(6) (3)

(8)(7)

Sealock-coated

PC(1)

Model Designation (Example)6(2)01

(3)M(4) (5)

(1) Type(2) Tube dia. (øD) or Thread size (T)

Code 180 3 4 6 5/32 1/8

Dia. ø1.8 ø3 ø4 ø6 ø5/32 ø1/8

mm size inch size

* In case (2) is thread size, please choose from the table (3).

(3) Thread size (T) or Tube dia. (øD)

Code M3 M5 M6 01 02

size M3×0.5 M5×0.8 M6×1 R1/8 R1/4

Metric thread Taper pipe thread

* In case (3) is tube size, please choose from the table (2).

Code U10 N0 N1

size 10-32UNF NPT1/16 NPT1/8

Unified fine thread American standard taper pipe thread

(4) Specification/Package option Code M MW MC MWC

Package Clasification Std. pkg Clean-room pkg Specification Mini-Std. Mini-light-gray Mini-Std. Mini-light-grayRelease-ring mm tube Black Light gray Light blue Light gray color inch tube White White White White Resin body color Black Light gray Light gray Light gray

Applicable thread size M, R M, R M, R M, R

UNF, NPT (not available for UNF or NPT as standard)

Before using the PISCO device, be sure to read the "Safety Instructions", "Common Safety Instructions for Products Listed in This Manual" on page 13 to 15 and "Common Safety Instructions for Quick-Fitting Joint" on page 18 to 19.

Detailed Safety Instructions

▲

In case of ordering, please apply Model code in the following chart.

Ultra-small Quick-Fitting Joint for Pneumatic Piping

(5) Wrench size specificationU: inch spec. (NPT, UNF)No code: mm spec. (M, R)

Tube dia.: ø6mm

Tube dia.: ø6mm

Thread size: R1/8 Thread size: R1/8

Mini-Type Standard Type

PCStraight

Model typeStandard pkg

PCøD-TM PCøD-TMU PCøD-TM CPC180-M3MPC180-M5MPC180-01MPC3-M3MPC3-M5MPC3-M6MPC3-01MPC4-M3MPC4-M5MPC4-M6MPC4-01MPC4-02MPC6-M5MPC6-M6MPC6-01MPC6-02MPC6-03MPC1/8-M3MPC1/8-M5MPC1/8-M6MPC1/8-01MPC5/32-M3MPC5/32-M5MPC5/32-M6MPC5/32-01MPC5/32-02MPC1/4-M5MPC1/4-M6MPC1/4-M7MPC1/4-01MPC1/4-02MPC1/4-03M

PC1/8-U10MUPC1/8-N0MUPC1/8-N1MUPC1/8-N2MU *¹PC5/32-U10MUPC5/32-N0MUPC5/32-N1MUPC5/32-N2MUPC1/4-U10MUPC1/4-N0MUPC1/4-N1MUPC1/4-N2MU

PC180-M3M CPC180-M5M CPC180-01M CPC3-M3M CPC3-M5M CPC3-M6M CPC3-01M CPC4-M3M CPC4-M5M CPC4-M6M CPC4-01M CPC4-02M CPC6-M5M CPC6-M6M CPC6-01M CPC6-02M CPC6-03M CPC1/8-M3M CPC1/8-M5M CPC1/8-M6M CPC1/8-01M CPC5/32-M3M CPC5/32-M5M CPC5/32-M6M CPC5/32-01M CPC5/32-02M CPC1/4-M5M CPC1/4-M6M CPC1/4-M7M CPC1/4-01M CPC1/4-02M CPC1/4-03M C

øD

T

Cautions*1. Custom-made, build to

order production*2. The white-letter model

type in ■ is new model.*3. is replaced with "W" if Light-

gray specifi cation is required otherwise please leave it blank.

*4. The option: W, C, or WC is build to order production.

*5. The model with low sales average may be bui ld to order production. For details, please contact Pisco sales offi ce or sales representative.

Package specifi cations10 pcs. in a bag: Mini-Std. pkg1 pc. in a bag (10 pcs./set): Mini clean-room pkg

PCFFemale Straight


PCFøD-TM PCFøD-TMU PCFøD-TM CPCF180-M3MPCF3-M3MPCF3-M5MPCF4-M3MPCF4-M5MPCF6-M5MPCF1/8-M3MPCF1/8-M5MPCF5/32-M3MPCF5/32-M5MPCF1/4-M5M

PCF1/8-U10MUPCF5/32-U10MUPCF1/4-U10MUPCF4-U10MU *¹

PCF180-M3M CPCF3-M3M CPCF3-M5M CPCF4-M3M CPCF4-M5M CPCF6-M5M CPCF1/8-M3M CPCF1/8-M5M CPCF5/32-M3M CPCF5/32-M5M CPCF1/4-M5M C

T

øD

Model typeClean-room pkg


PUUnion Straight


PUøDM PUøDM CPU180MPU3MPU4MPU6M

PU1/8MPU5/32MPU1/4M

PU180M CPU3M CPU4M CPU6M C

øD

øD


PU1/8M CPU5/32M CPU1/4M C

: 1. The mechanical part of a fitting, including a cleanroom package specification, slides slightly by an internal pressure change, and dusts may be generated. Therefore, please prevent using the fitting in the cleanroom of ISO class 1 to 5. If tube and fitting oscillate or fluctuate, please detemine an amount of dust on actual equipment by repeating test runs prior to the start of operation.

Caution

* Please also check a color chart on page 000 & 000.

*1. (8) Metallic body of M3 is nickel-plated free cutting steel. However, M3 of tube o.d. ø1.8mm fitting is either nickel-plated free-cutting steel or free-cutting stainless steel.

*2. The gasket of M or UNF thread is made of SUS304 + NBR, but it is made of POM if the fitting is clean-room package specification (C or WC).

The products listed in this page are ECO-friendly products.* Please refer to page 4 for the details of ECO-friendly products.

2011_fitting-1 11.8.4, 1:21 PM27

28


PBBranch Tee


PBøD-T M PBøD-TMU PBøD-TM CPB180-M3MPB180-M5MPB3-M3MPB3-M5MPB3-M6MPB3-01MPB4-M3MPB4-M5MPB4-M6MPB4-01MPB4-02MPB6-M5MPB6-M6MPB6-01MPB6-02MPB6-03MPB1/8-M3MPB1/8-M5MPB1/8-M6MPB1/8-01MPB5/32-M3MPB5/32-M5MPB5/32-M6MPB5/32-01MPB5/32-02MPB1/4-M5MPB1/4-M6MPB1/4-01MPB1/4-02MPB1/4-03M

PB1/8-U10MUPB1/8-N0MUPB1/8-N1MUPB5/32-U10MUPB5/32-N0MUPB5/32-N1MUPB5/32-N2MUPB1/4-U10MUPB1/4-N0MUPB1/4-N1MUPB1/4-N2MUPB1/4-N3MU

PB180-M3M CPB180-M5M CPB3-M3M CPB3-M5M CPB3-M6M CPB3-01M CPB4-M3M CPB4-M5M CPB4-M6M CPB4-01M CPB4-02M CPB6-M5M CPB6-M6M CPB6-01M CPB6-02M CPB6-03M CPB1/8-M3M CPB1/8-M5M CPB1/8-M6M CPB1/8-01M CPB5/32-M3M CPB5/32-M5M CPB5/32-M6M CPB5/32-01M CPB5/32-02M CPB1/4-M5M CPB1/4-M6M CPB1/4-01M CPB1/4-02M CPB1/4-03M C

øD T

øD

PDRun Tee


PDøD-TM PDøD-TMU PDøD-TM CPD180-M3MPD180-M5MPD3-M3MPD3-M5MPD3-M6MPD3-01MPD4-M3MPD4-M5MPD4-M6MPD4-01MPD4-02MPD6-M5MPD6-M6MPD6-01MPD6-02MPD6-03MPD1/8-M3MPD1/8-M5MPD1/8-M6MPD1/8-01MPD5/32-M3MPD5/32-M5MPD5/32-M6MPD5/32-01MPD5/32-02MPD1/4-M5MPD1/4-M6MPD1/4-01MPD1/4-02MPD1/4-03M

PD1/8-U10MUPD1/8-N0MUPD1/8-N1MUPD5/32-U10MUPD5/32-N0MUPD5/32-N1MUPD5/32-N2MUPD1/4-U10MUPD1/4-N0MUPD1/4-N1MUPD1/4-N2MUPD1/4-N3MU

PD180-M3M CPD180-M5M CPD3-M3M CPD3-M5M CPD3-M6M CPD3-01M CPD4-M3M CPD4-M5M CPD4-M6M CPD4-01M CPD4-02M CPD6-M5M CPD6-M6M CPD6-01M CPD6-02M CPD6-03M CPD1/8-M3M CPD1/8-M5M CPD1/8-M6M CPD1/8-01M CPD5/32-M3M CPD5/32-M5M CPD5/32-M6M CPD5/32-01M CPD5/32-02M CPD1/4-M5M CPD1/4-M6M CPD1/4-01M CPD1/4-02M CPD1/4-03M C

øD

T

øD

POCInner Hex. Straight


POCøD-TM POCøD-TMU POCøD-TM CPOC180-M3MPOC3-M3MPOC3-M5MPOC3-M6MPOC4-M3MPOC4-M5MPOC4-M6MPOC4-01MPOC6-M5MPOC6-M6MPOC6-01MPOC1/8-M3MPOC1/8-M5MPOC1/8-M6MPOC1/8-M7M *¹POC5/32-M3MPOC5/32-M5M *¹POC5/32-M6MPOC5/32-01MPOC3/16-M5M *¹POC1/4-M5MPOC1/4-M6MPOC1/4-M7MPOC1/4-01M

POC1/8-U10MUPOC5/32-U10MUPOC5/32-N1MUPOC3/16-U10MU *¹POC3/16-N1MU *¹POC1/4-U10MUPOC1/4-N0MUPOC1/4-N1MU

POC180-M3M CPOC3-M3M CPOC3-M5M CPOC3-M6M CPOC4-M3M CPOC4-M5M CPOC4-M6M CPOC4-01M CPOC6-M5M CPOC6-M6M CPOC6-01M CPOC1/8-M3M CPOC1/8-M5M CPOC1/8-M6M CPOC1/8-M7M C *¹POC5/32-M3M CPOC5/32-M5M C *¹POC5/32-M6M CPOC5/32-01M CPOC3/16-M5M C *¹POC1/4-M5M CPOC1/4-M6M CPOC1/4-M7M CPOC1/4-01M C

T

øD

PLLLong Elbow


PLLøD-TM PLLøD-TMU PLLøD-TM CPLL180-M3MPLL180-M5MPLL3-M3MPLL3-M5MPLL3-M6MPLL3-01MPLL4-M3MPLL4-M5MPLL4-M6MPLL4-01MPLL4-02MPLL6-M5MPLL6-M6MPLL6-01MPLL6-02MPLL6-03MPLL1/8-M3MPLL1/8-M5MPLL1/8-M6MPLL1/8-01MPLL5/32-M3MPLL5/32-M5MPLL5/32-M6MPLL5/32-01MPLL5/32-02MPLL1/4-M5MPLL1/4-M6MPLL1/4-01MPLL1/4-02MPLL1/4-03M

PLL1/8-U10MUPLL1/8-N0MUPLL1/8-N1MUPLL5/32-U10MUPLL5/32-N0MUPLL5/32-N1MUPLL5/32-N2MUPLL1/4-U10MUPLL1/4-N0MUPLL1/4-N1MUPLL1/4-N2MUPLL1/4-N3MU

PLL180-M3M CPLL180-M5M CPLL3-M3M CPLL3-M5M CPLL3-M6M CPLL3-01M CPLL4-M3M CPLL4-M5M CPLL4-M6M CPLL4-01M CPLL4-02M CPLL6-M5M CPLL6-M6M CPLL6-01M CPLL6-02M CPLL6-03M CPLL1/8-M3M CPLL1/8-M5M CPLL1/8-M6M CPLL1/8-01M CPLL5/32-M3M CPLL5/32-M5M CPLL5/32-M6M CPLL5/32-01M CPLL5/32-02M CPLL1/4-M5M CPLL1/4-M6M CPLL1/4-01M CPLL1/4-02M CPLL1/4-03M C

øD

T

POLHex. Holed Banjo


POLøD-TMPOL3-M5MPOL4-M5MPOL6-M5MPOL1/8-M5MPOL5/32-M5M

TøD

POLLHex. Holed Long Banjo


POLLøD-TMPOLL3-M5MPOLL4-M5MPOLL6-M5MPOLL1/8-M5MPOLL5/32-M5M

T

øD

PLElbow


PLøD-TM PLøD-TMU PLøD-TM CPL180-M3MPL180-M5MPL180-01MPL3-M3MPL3-M5MPL3-M6MPL3-01MPL4-M3MPL4-M5MPL4-M6MPL4-01MPL4-02MPL6-M5MPL6-M6MPL6-01MPL6-02MPL6-03MPL1/8-M3MPL1/8-M5MPL1/8-M6MPL1/8-01MPL5/32-M3MPL5/32-M5MPL5/32-M6MPL5/32-01MPL5/32-02MPL1/4-M5MPL1/4-M6MPL1/4-M7MPL1/4-01MPL1/4-02MPL1/4-03M

PL1/8-U10MUPL1/8-N0MUPL1/8-N1MUPL1/8-N2MU *1

PL5/32-U10MUPL5/32-N0MUPL5/32-N1MUPL5/32-N2MUPL1/4-U10MUPL1/4-N0MUPL1/4-N1MUPL1/4-N2MUPL1/4-N3MU

PL180-M3M CPL180-M5M CPL180-01M CPL3-M3M CPL3-M5M CPL3-M6M CPL3-01M CPL4-M3M CPL4-M5M CPL4-M6M CPL4-01M CPL4-02M CPL6-M5M CPL6-M6M CPL6-01M CPL6-02M CPL6-03M CPL1/8-M3M CPL1/8-M5M CPL1/8-M6M CPL1/8-01M CPL5/32-M3M CPL5/32-M5M CPL5/32-M6M CPL5/32-01M CPL5/32-02M CPL1/4-M5M CPL1/4-M6M CPL1/4-M7M CPL1/4-01M CPL1/4-02M CPL1/4-03M C

øDT

Cautions*1. Custom-made, build to order production*2. The white-letter model type in ■ is new model.*3. is replaced with "W" if Light-gray specifi cation is

required otherwise please leave it blank.*4. The option: W, C, or WC is build to order production.*5. The model with low sales average may be build to order

production. For details, please contact Pisco sales offi ce or sales representative.


POL1/8-U10MUPOL5/32-U10MU

POLøD-TMU

POLLøD-TMUPOLL1/8-U10MUPOLL5/32-U10MU

PCCCartridge

Model type Standard pkgPCCøD-TM PCCøD-TM CPCC3-M6MPCC4-M6MPCC4-M8MPCC6-M8MPCC1/8-M6M

PCC3-M6M CPCC4-M6M CPCC4-M8M CPCC6-M8M CPCC1/8-M6M C

T

øD

PLH45-degree Elbow

Model type Standard pkgPLHøD-TM PLHøD-TM C

PLH3-M3MPLH3-M5MPLH4-M3MPLH4-M5MPLH4-M6MPLH4-01MPLH6-M5MPLH6-M6MPLH6-01MPLH6-02M *¹

PLH3-M3M CPLH3-M5M CPLH4-M3M CPLH4-M5M CPLH4-M6M CPLH4-01M CPLH6-M5M CPLH6-M6M CPLH6-01M CPLH6-02M C

T

øD




POLøD-TM CPOL3-M5M CPOL4-M5M CPOL6-M5M CPOL1/8-M5M CPOL5/32-M5M C



POLL3-M5M CPOLL4-M5M CPOLL6-M5M CPOLL1/8-M5M CPOLL5/32-M5M C

POLLøD-TM C






2011_fitting-1 11.8.4, 1:21 PM28

29

Fitting

Control

Valve

Vacuum

Actuator

Tube

Plarailchain

Robot Parts

PVUnion Elbow

Model type: Standard pkgPVøDM PVøDM C

PV180MPV3MPV4MPV6M

PV1/8MPV5/32MPV1/4M

PV180M CPV3M CPV4M CPV6M C

øD

PEUnion Tee

Model type: Standard pkgPEøDM PEøDM C

PE180MPE3MPE4MPE6M

PE1/8MPE5/32MPE1/4M

PE180M CPE3M CPE4M CPE6M CøD øD

øD

øD

PYUnion Y

Model type: Standard pkgPYøDM PYøDM C

PY3MPY4MPY6M

PY1/8MPY5/32MPY1/4M

PY3M CPY4M CPY6M C

øD

øD

PGUnequal Union Straight

Model type: Standard pkgPGøD1-øD2M PGøD1-øD2M C

PG3-180MPG4-180MPG4-3MPG4-1/8MPG6-3MPG6-1/8MPG6-4M

PG5/32-1/8MPG3/16-1/8M *¹PG1/4-1/8MPG1/4-5/32M

PG3-180M CPG4-180M CPG4-3M CPG4-1/8M CPG6-3M CPG6-1/8M CPG6-4M C

øD2

øD1

PGJUnequal Plug-in Straight

Model type: Standard pkgPGJøD1-øD2M

PGJ3-1/8MPGJ3-180MPGJ3-4MPGJ3-6MPGJ4-180MPGJ4-3MPGJ4-1/8MPGJ4-6MPGJ6-3MPGJ6-1/8MPGJ6-4MPGJ6-1/4M

PGJ1/8-5/32MPGJ1/8-1/4MPGJ5/32-1/8MPGJ5/32-1/4MPGJ3/16-1/8MPGJ3/16-5/32MPGJ3/16-1/4MPGJ1/4-1/8MPGJ1/4-5/32MPGJ1/4-6M

øD2

øD1

PLJPlug-in Elbow

Model type: Standard pkgPLJøDM

PLJ3MPLJ4MPLJ6M

PLJ1/8MPLJ5/32MPLJ3/16MPLJ1/4M

øD øD

PLGJUnequal Plug-in Elbow

Model type: Standard pkgPLGJøD1-øD2M

PLGJ3-180MPLGJ3-1/8MPLGJ3-4MPLGJ3-6MPLGJ4-180MPLGJ4-3MPLGJ4-1/8MPLGJ4-6MPLGJ6-3MPLGJ6-1/8MPLGJ6-4MPLGJ6-1/4M

PLGJ1/8-3MPLGJ1/8-5/32MPLGJ1/8-1/4MPLGJ5/32-1/8MPLGJ5/32-1/4MPLGJ3/16-1/8MPLGJ3/16-5/32MPLGJ3/16-1/4MPLGJ1/4-1/8MPLGJ1/4-5/32MPLGJ1/4-6M

øD2

øD1

PYJPlug-in Y

Model type: Standard pkgPYJøDM

PYJ3MPYJ4MPYJ6M

PYJ1/8MPYJ5/32M

øD

øD

PWJUnequal Plug-in Y

Model type: Standard pkgPWJøD1-øD2M

PWJ4-3MPWJ6-3MPWJ6-4MPWJ4-1/8MPWJ6-1/8M

øD2

øD1PZACross A

Model type: Standard pkgPZAøDM

PZA3MPZA4MPZA6M

PZA1/8MPZA5/32M

øD

øD

PZBCross B

Model type: Standard pkgPZBøD1-øD2M

PZB4-3MPZB6-4MPZB4-1/8MPZB6-1/8MPZB1/8-3M

øD2 øD1

PZCCross C

Model type: Standard pkgPZCøD1-øD2M

PZC4-3MPZC6-4MPZC4-1/8MPZC6-1/8MPZC1/8-3M

øD2 øD1

øD

øD

øD1

øD2øD2

øD2

Cautions*1. Custom-made, build to order production*2. The white-letter model type in ■ is new model.*3. is replaced with "W" if Light-gray specifi cation is required otherwise please leave it blank.*4. The option: W, C, or WC is build to order production.*5. The model with low sales average may be build to order production. For details, please contact

Pisco sales offi ce or sales representative.


PPPlug

Model type: Standard pkgPPøDM

PP180MPP3M

øDPP1/8M

PXBranch Y

Model type Standard pkgPXøD-TMU

PX1/8-N1MUPX1/8-N2MU

T

øD

PWJ5/32-1/8M

PZB5/32-1/8M

PZC5/32-1/8M

PIJUnion Stem

Model type: Standard pkgPIJøDM

PIJ3MøDøD

PIJ1/8M

Model type: Clean-room pkg



PV1/8M CPV5/32M CPV1/4M C

PE1/8M CPE5/32M CPE1/4M C

PY1/8M CPY5/32M CPY1/4M C

PG5/32-1/8M CPG1/4-1/8M CPG1/4-5/32M C


Model type: Clean-room pkgPGJøD1-øD2M C

PGJ3-1/8M CPGJ3-180M CPGJ3-4M CPGJ3-6M CPGJ4-180M CPGJ4-3M CPGJ4-1/8M CPGJ4-6M CPGJ6-3M CPGJ6-1/8M CPGJ6-4M CPGJ6-1/4M C

PGJ1/8-5/32M CPGJ1/8-1/4M CPGJ5/32-1/8M CPGJ5/32-1/4M CPGJ3/16-1/8M CPGJ3/16-5/32M CPGJ3/16-1/4M CPGJ1/4-1/8M CPGJ1/4-5/32M CPGJ1/4-6M C

Model type: Clean-room pkgPLJøDM C

PLJ3M CPLJ4M CPLJ6M C

PLJ1/8M CPLJ5/32M CPLJ3/16M CPLJ1/4M C

Model type: Clean-room pkgPLGJøD1-øD2M C

PLGJ3-180M CPLGJ3-1/8M CPLGJ3-4M CPLGJ3-6M CPLGJ4-180M CPLGJ4-3M CPLGJ4-1/8M CPLGJ4-6M CPLGJ6-3M CPLGJ6-1/8M CPLGJ6-4M CPLGJ6-1/4M C

PLGJ1/8-3M CPLGJ1/8-5/32M CPLGJ1/8-1/4M CPLGJ5/32-1/8M CPLGJ5/32-1/4M CPLGJ3/16-1/8M CPLGJ3/16-5/32M CPLGJ3/16-1/4M CPLGJ1/4-1/8M CPLGJ1/4-5/32M CPLGJ1/4-6M C

Model type: Clean-room pkgPYJøDM C

PYJ3M CPYJ4M CPYJ6M C

PYJ1/8M CPYJ5/32M C

Model type: Clean-room pkgPWJøD1-øD2M C

PWJ4-3M CPWJ6-3M CPWJ6-4M CPWJ4-1/8M CPWJ6-1/8M C

Model type: Clean-room pkgPZAøDM C

PZA3M CPZA4M CPZA6M C

PZA1/8M CPZA5/32M C

Model type: Clean-room pkgPZBøD1-øD2M C

PZB4-3M CPZB6-4M CPZB4-1/8M CPZB6-1/8M CPZB1/8-3M C

Model type: Clean-room pkgPZCøD1-øD2M C

PZC4-3M CPZC6-4M CPZC4-1/8M CPZC6-1/8M CPZC1/8-3M C

PWJ5/32-1/8M C

PZB5/32-1/8M C

PZC5/32-1/8M C

Model type: Clean-room pkgPIJøDM C

PIJ3M C PIJ1/8M C

PEGUnequal Union Tee

Model type: Standard pkgPEGøD1-øD2M PEGøD1-øD2M C

PEG3-180MPEG3-4MPEG4-3MPEG4-1/8MPEG4-6MPEG6-4M

PEG1/8-5/32MPEG5/32-1/8MPEG5/32-1/4MPEG1/4-5/32M

PEG3-180M CPEG3-4M CPEG4-3M CPEG4-1/8M CPEG4-6M CPEG6-4M C

øD2

øD1

øD1

PWUnequal Union Y

Model type: Standard pkgPWøD1-øD2M PWøD1-øD2M C

PW4-3MPW6-3MPW6-4MPW4-1/8MPW6-1/8MPW1/8-3M

PW5/32-1/8MPW1/4-1/8MPW1/4-5/32M

PW4-3M CPW6-3M CPW6-4M CPW4-1/8M CPW6-1/8M CPW1/8-3M C

øD1

øD2

PMBulkhead Union

Model type: Standard pkgPMøDM PMøDM C

PM3MPM4MPM6M

PM1/8MPM5/32MPM1/4M

PM3M CPM4M CPM6M C

øD

øD

PEG1/8-5/32M CPEG5/32-1/8M CPEG5/32-1/4M CPEG1/4-5/32M C



PM1/8M CPM5/32M CPM1/4M C


PW5/32-1/8M CPW1/4-1/8M CPW1/4-5/32M C

Model type: Clean-room pkgPPøDM C

PP180M CPP3M C

PP1/8M C


2011_fitting-1 11.8.4, 1:22 PM29

30


PLHJ45-degree Plug-in Elbow

Model type Standard pkgPLHJøDM

PLHJ4MPLHJ6M

øDøD

PPFCap

Model type Standard pkgPPFøDM

PPF180MPPF3M

øD

PFExtension Screw Adaptor

Model type Standard pkg

PF T-T1MPFM5-M3MPF01-M3MT

T1

PLLJLong Plug-in Elbow

Model type Standard pkgPLLJøDM

PLLJ3/16MøD øD PPF180M CPPF3M C

Model typeClean-room pkgPPFøDM C

Model typeClean-room pkgPLHJøDM CPLHJ4M CPLHJ6M C


PF T-T1MCPFM5-M3MCPF01-M3MC

Model typeClean-room pkgPLLJøDM CPLLJ3/16M C

Cautions*1. Custom-made, build to order production*2. The white-letter model type in ■ is new model.*3. is replaced with "W" if Light-gray specifi cation is required otherwise please leave it blank.*4. The option: W, C, or WC is build to order production.*5. The model with low sales average may be build to order production. For details, please

contact Pisco sales offi ce or sales representative.



2011_fitting-1 11.8.4, 1:23 PM30

18

Tube end

Sealing

The tube is not inserted to the tube end.

Good example: Bad example:

Common Safety Instructions for Quick-Fitting JointBe sure to read the following instructions before selecting and using the PISCO devices. Also read the detailed instructions for individual series.

: 1. Never use the Quick-Fitting Joint with fluid medium other than air or water (usable with some models). For applications with fluid medium other than air or water, contact PISCO for instructions.

2. Never use joints other than Tube Fitting Spatter or other all metal joints where they are exposed to spatter. Otherwise spatter can cause fire.3. For applications in which the threaded side or the tube connection side is subject to vibration or rotation, use Rotary Joints, High Rotary Joints or

Multi-Circuit Rotary Blocks only. Swinging or rotation may damage the joint body.4. For applications with hot water of 60°C (140°F) or above or thermal oil, use no other joints than Die Temperature Control Fittings, Tube Fitting Stainless

SUS316, Tube Fitting Stainless SUS316 Compression Fitting, and All Brass Compression Fitting. Heat or hydrolysis may damage the joint body.5. For applications in which the scattering of static electricity or charging must be prevented, use no other joints than anti-static (EG) Joints. Static electricity

may cause system malfunction or trouble.6. Do not allow tension, twist or bending forces to act on the joints. Undue forces may damage the joint body.

Warnings

: 1. When you use tubes of brands other than ours, be sure to confirm that the outside diameter of the tubes satisfies the tolerance specified in Table 1.Cautions

Table 1. Tube O.D. Tolerance

mm size Nylon tube Polyurethane tube ø1.8mm – ±0.05mm ø3mm – ±0.15mm ø4mm ±0.1mm ±0.15mm ø6mm ±0.1mm ±0.15mm ø8mm ±0.1mm ±0.15mm ø10mm ±0.1mm ±0.15mm ø12mm ±0.1mm ±0.15mm ø16mm ±0.1mm ±0.15mm

inch size Nylon tube Polyurethane tube ø1/8 ±0.0039in. ±0.0059in. ø5/32 ±0.0039in. ±0.0059in. ø3/16 ±0.0039in. ±0.0059in. ø1/4 ±0.0039in. ±0.0059in. ø5/16 ±0.0039in. ±0.0059in. ø3/8 ±0.0039in. ±0.0059in. ø1/2 ±0.0039in. ±0.0059in. ø5/8 ±0.0039in. ±0.0059in.

2. Cautions on the fitting of tube(1) Make certain that the end of the tube is cut at right angles, the tube surface is free from flaws, and the tube is not deformed into an ellipse.(2) When fitting a tube, insert the tube to the tube end completely as drawings shown below to prevent leakage.(3) On completion of fitting, make certain that the tube does not come out at your pulling.

2011_fitting-1 11.8.4, 1:17 PM18

19

Fitting

Control

Valve

Vacuum

Actuator

Tube

Plarailchain

Robot Parts

3. Cautions on the release of tube(1) Before releasing the tube, make certain that the pressure inside the tube is zero.(2) Push the release ring fully inside and pull out the tube. Unless you push it completely in, the tube may not come out and scrapings of tube may be left

inside the joint.4. Cautions on the installation of joint body

(1) When installing the joint body, tighten it with a proper tool, using the outside or inside hexagon.(2) In tightening the screw, use the tightening torque recommended in Table 3.

• Use of a torque higher than the recommended level may damage thread or deform gasket, thus causing leaks.• Use of a torque lower than the recommended level may cause loose screw and leakage.

(3) With the joint whose piping direction will not change after tightening, make adjustment within the recommended range of tightening torques.

Table 3. Recommended Tightening Torque, Sealock Color and Gasket Material

Thread type Thread size Tightening torque Sealock color Gasket material M3×0.5 0.7N·m (0.52lbf·ft) M5×0.8 1.0 ~ 1.5N·m (0.74 ~ 1.11lbf·ft) n/a SUS304, NBR M6×1.0 2.0 ~ 2.7N·m (1.48 ~ 1.99lbf·ft)

Metric thread M3×0.5 0.5 ~ 0.6N·m (0.37 ~ 0.44lbf·ft)

(JIS B0205, ISO0261)

M5×0.8 1.0 ~ 1.5N·m (0.74 ~ 1.11lbf·ft) n/a

POM (Polyacetal)

M6×0.75 0.8 ~ 1.0N·m (0.59 ~ 0.74lbf·ft) M8×0.75 1.0 ~ 2.0N·m (0.74 ~ 1.48lbf·ft) R1/8 7 ~ 9N·m (5.16 ~ 6.64lbf·ft) Taper pipe thread R1/4 12 ~ 14N·m (8.85 ~ 10.33lbf·ft)

White n/a (JIS B0203, ISO 7/1, BS21) R3/8 22 ~ 24N·m (16.23 ~ 17.70lbf·ft) R1/2 28 ~ 30N·m (20.65 ~ 22.13lbf·ft) Unified thread (ANSI/ASME B1.1) No. 10-32UNF 1.0 ~ 1.5N·m (0.74 ~ 1.11lbf·ft) n/a SUS304, NBR 1/16-28NPT 7 ~ 9N·m (5.16 ~ 6.64lbf·ft)

National Pipe 1/8-27NPT 7 ~ 9N·m (5.16 ~ 6.64lbf·ft)

Thread Taper

1/4-18NPT 12 ~ 14N·m (8.85 ~ 10.33lbf·ft) White n/a

(American standard) 3/8-18NPT 22 ~ 24N·m (16.23 ~ 17.70lbf·ft)

(ANSI/ASME B1.20.1)

1/2-14NPT 28 ~ 30N·m (20.65 ~ 22.13lbf·ft)* Remarks: Since the torque may differ by products, please also look at caution of each product.

5. Cautions on the removal of joint body(1) When removing the joint body, loose it with a proper tool, using the outside or inside hexagon.(2) Remove sealant sticking to the thread on the mating equipment. The sealant left sticking may enter the peripheral equipment and cause trouble.

6. Please install in such a way that neither twisting, pulling, moment load, vibrations, nor shocks are given to a joint or a tube. It becomes causes of breakage of a joint, crushing, or loosing of a tube.

2011_fitting-1 11.8.4, 1:17 PM19

13

Safety InstructionsThis Safety Instructions aim to prevent injuries to human bodies and damage to properties by requiring proper use of PISCO devices.Also the relevant requirements of ISO 4414 and JIS B8370 must be observed.ISO 4414: Pneumatic fluid power … Recomendations for the application of equipment to transmission and control systems.JIS B 8370: General standards for pneumatic systemsSafety instructions are classified into "Danger", "Warning" and "Caution", depending on the degree of danger or damage involved when the safety instructions are not complied with in handling the equipment.

: Failure to heed the warning of apparent danger may result in death or serious injuries.Danger

: Failure to heed the warning of conditionally dangerous situations may result in death or serious injuries.Warning

: Failure to heed the warning of conditionally dangerous situations may result in minor or not too serious injuries or damage to properties.Caution

* Safety Instructions are subject to change without advance notice.

: 1. Make a selection of pneumatic equipment.(1) Well knowledgeable and experienced persons such as a pneumatic system designer or who is in charge of deciding specification should select

pneumatic equipment.(2) The applicable conditions of the products in this catalogue are diverse. Therefore, judge the conformity of systems with required analysis or tests

by system designers or persons who is in charge of deciding specifications. The guarantee of initial performance and safety of the system is on responsibility of the person who decides specifications. Hereafter, examine all the specification with updated products catalogues and technical documents in order to avoid malfunctions of equipment, and then develop systems.

2. Handle pneumatic equipment with enough knowledge and experience.(1) Mishandling of compressed air is dangerous. Conduct assembly, operation and maintenance of devises with pneumatic equipment by persons with

enough knowledge and experience.3. Do not operate and remove the equipment until safety is confirmed.

(1) Conduct inspection and maintenance of equipment after confirming fail-proof measures of work pieces or runaway-proof device are properly working.(2) When removing equipment, make sure that above safety measures are conducted. Then, stop air supply and electric source of equipment making sure

the pressure inside the system is zero before removing equipment.(3) When re-activate equipment, make sure safety measures against fly-out are taken and re-activate equipment with care.

Warning

2011_index 11.8.4, 5:40 PM13

14

Common Safety Instructions for Products Listed in This ManualPISCO products are designed and manufactured for use with general industrial machinery and equipment. Therefore be sure to observe the following safety instructions:

: 1. Avoid the following uses for PISCO devices:(1) Use under conditions not specified for the device(2) Use in any outdoor environment(3) Use in locations where the device is exposed to excessive vibration or shocks(4) Use in locations where the device is exposed to any corrosive gas, inflammable gas, chemicals, seawater, or vapor.* Certain PISCO devices, however, can be used in environments as described above. Therefore check on the specifications for the use of individual

devices.2. Do not disassemble or remodel the PISCO devices in such a way as may affect the basic structure, performance or function of them.3. Never touch the release ring of the Quick-Fitting Joint when there is pressure working on it. Touching may release the ring, which in turn may cause the

tube to fall out.4. Avoid too frequent switching of air pressure. Otherwise the device body may heat up to cause burns on you.5. Do not allow tension, twist or bending forces to act on the joints. Undue forces may damage the joint body.6. For applications in which the threaded side or the tube connection side is subject to vibration, use Rotary Joints, High Rotary Joints or Multi-Circuit Rotary

Blocks only. Swinging or rotation may damage the joint body.7. For applications with hot water of 60°C (140°F) or above or thermal oil, use no other joints than Die Temperature Control Fitting, Tube Fitting Stainless

SUS316, Tube Fitting Stainless SUS316 Compression Fitting, and All Brass Compression Fitting. Heat or hydolysis may damage the joint body.8. For applications in which the scattering of static electricity or charging must be prevented, use no other joints than EG Joints. Static electricity may cause

system malfunction or trouble.9. Never use joint other than Tube Fitting Spatter or Tube Fitting Brass where they are exposed to spatter. Otherwise can cause fire.10. Carry out maintenance and checks of equipment only after turning power off, shutting fluid off and making certain that the pressure in the piping has

dropped to zero. Please conduct maintenance after confirming following points. (1) Make sure that maintenance is safe for all the systems involving PISCO products. (2) When re-activate equipment after maintenance, make sure safety measures against fly-out are taken and re-activate equipment with care.(3) Please secure space for maintenance when the circuit is designed.

11. When the fluid is admitted to the equipment and if there is a possibility to cause damage to it due to leakage, conduct safety measures such as protect cover beforehand.

Warning

: 1. In installing the piping, be sure to remove dust or drainage from within the piping. Dust or drainage left unremoved may enter other equipment, thus causing troubles.

2. When using an ultrasoft tube to connect to a Quick-Fitting Joint, be sure to use an insert ring in the bore of the tube. Otherwise the tube may fall out to cause leakage.

3. When you use tubes of brands other than ours, be sure to confirm that the outside diameter of the tubes satisfies the tolerance specified Table 1.

Caution

Table 1. Tube O.D. Tolerance

mm size Nylon tube Urethane tube ø1.8mm – ±0.05mm ø3mm – ±0.15mm ø4mm ±0.1mm ±0.15mm ø6mm ±0.1mm ±0.15mm ø8mm ±0.1mm ±0.15mm ø10mm ±0.1mm ±0.15mm ø12mm ±0.1mm ±0.15mm ø16mm ±0.1mm ±0.15mm

inch size Nylon tube Urethane tube ø1/8 ±0.0039in. ±0.0059in. ø5/32 +0.0039in. ±0.0059in. ø3/16 ±0.0039in. ±0.0059in. ø1/4 ±0.0039in. ±0.0059in. ø5/16 +0.0039in. ±0.0059in. ø3/8 ±0.0039in. ±0.0059in. ø1/2 ±0.0039in. ±0.0059in. ø5/8 ±0.0039in. ±0.0059in.

: 1. Do not use PISCO devices with the following equipment:(1) Equipment used for the sustenance or control of people's health or lives(2) Equipment used for the movement or transport of people(3) Equipment used specifically to ensure safety

Danger

2011_index 11.8.4, 5:40 PM14

15

Tube end

Sealing: Elastic-sleeve

Tube is not inserted fully to tube end.

Release-ring

Lock claws

Tube

: NG: GOOD

(3) On completion of fitting, make certain that the tube does not come out at your pulling.5. Cautions on the release of tube

(1) Before releasing the tube, make certain that the pressure inside the tube is zero.(2) Push the release ring fully inside and pull out the tube. Unless you push it completely in, the tube may not come out and scrapings of tube may be left

inside the joint.6. Cautions on the installation of joint body

(1) When installing the joint body, tighten it with a proper tool, using the outside or inside hexagon.(2) In tightening the screw, use the tightening torque recommended in Table 3.

• Use of a torque higher than the recommended level may damage thread or deform gasket, thus causing leaks.• Use of a torque lower than the recommended level may cause loose screw and leakage.

(3) With the joint whose piping direction will not change after tightening, make adjustment within the recommended range of tightening torques.

Table 3. Tightening Torque, Sealock Color and Gasket Material

Thread type Thread size Tightening torque Sealock color Gasket material M3×0.5 0.7N·m (0.52lbf·ft) M5×0.8 1.0 ~ 1.5N·m (0.74 ~ 1.11lbf·ft) n/a SUS304, NBR M6×1.0 2.0 ~ 2.7N·m (1.48 ~ 1.99lbf·ft) Metric thread M3×0.5 0.5 ~ 0.6N·m (0.37 ~ 0.44lbf·ft) M5×0.8 1.0 ~ 1.5N·m (0.74 ~ 1.11lbf·ft)

n/a POM (Polyacetal) M6×0.75 0.8 ~ 1.0N·m (0.59 ~ 0.74lbf·ft) M8×0.75 1.0 ~ 2.0N·m (0.74 ~ 1.48lbf·ft) R1/8 7 ~ 9N·m (5.16 ~ 6.64lbf·ft)

Taper pipe thread R1/4 12 ~ 14N·m (8.85 ~ 10.33lbf·ft)

White n/a R3/8 22 ~ 24N·m (16.23 ~ 17.70lbf·ft) R1/2 28 ~ 30N·m (20.65 ~ 22.13lbf·ft) Unified thread No. 10-32UNF 1.0 ~ 1.5N·m (0.74 ~ 1.11lbf·ft) n/a SUS304, NBR 1/16-28NPT 7 ~ 9N·m (5.16 ~ 6.64lbf·ft)

National Pipe Thread Taper 1/8-27NPT 7 ~ 9N·m (5.16 ~ 6.64lbf·ft)

(American standard)

1/4-18NPT 12 ~ 14N·m (8.85 ~ 10.33lbf·ft) Gray n/a 3/8-18NPT 22 ~ 24N·m (16.23 ~ 17.70lbf·ft) 1/2-14NPT 28 ~ 30N·m (20.65 ~ 22.13lbf·ft)

7. Cautions on the removal of joint body(1) When removing the joint body, loosen it with a proper tool, using the outside or inside hexagon.(2) Remove sealant sticking to the thread on the mating equipment. The sealant left sticking may enter the perpheral equipment and cause trouble.

8. Clean-room package option* The product is washed by clean air after assemblying in the normal assembly process as same condition as standard specification model. Then, it is

packed in ISO class 6 clean-room.

4. Cautions on the fitting of tube(1) Make certain that the end of the tube is cut at right angles, the tube surface is free from flaws, and the tube is not deformed into an ellipse.(2) When fitting a tube, insert the tube to the tube end completely as drawings shown below to prevent leakage.

Recommended tightening torque for silencerThread Type Thread Size Tightening Torque

Metric threadM5×0.8

1/6 turn after hand-tighteningM6×1.0M10×1.0

Parallele pipe thread

G1/8

1/2 ~ 1 turn after hand-tighteningG1/4G3/8G1/2

2011_index 11.8.4, 5:40 PM15

321

Body color option

P.322

Based on the standard products, "Special specifi cation option" on parts for matching operating environment or "Special appearance option" for matching a color for operating environment can be selected and ordered by just adding prearranged extension code of options.* Pisco welcomes an inquiry of custom-made product, which is not listed in this catalog. Please feel free to contact nearest Pisco offi ce.

Seal rubber option

Oil-free specification

Release-ring color option

Non-purple specification

Build to Order Production

* No Cu or F ion generation

P.322 P.322 P.322 P.322

2011_order_production-1 11.8.4, 4:50 PM321

322

Sealock coatStandard of screw size

Standard of Tube size

Color and Shape of Release ringBody color

Gasket

Rubber material and lubricant

Special Options

Outer color change• Change the color of resin body and release-ring to light-gray.

Characteristics

Change of outer color, sealing material, lubrication, etc.

Model Designation (Example)W(2)

(1) Model designation of standard product (please refer to applicable products on next page.)(2) Color

PL6━01(1)

Code W No code

Color Light-gray Standard

Sealing material change• Change the sealing material to FKM or EPDM depending on an application.

Oil-free specification• Prevent oil running into fluid medium because the product is assembled without using oil.

━F(3)━D(4) (5) (6)

* If light-gray (W) is selected for resin color, the metric (mm) size release-ring color becomes light-gray even for combination with any other options.

* The color of release-ring of inch tube size is always white.

(3) Sealing material Code -F -E No code

Material FKM EPDM（Oil-free） Standard rubber*1. For FKM (-F) specification, the color of metric (mm) size release-ring becomes brown. while inch tube

size is white. FKM (-F) specification can not be combined with non-purple (-P) specification.*2. For EPDM (-E) specification, the product is assembled as oil-free specification. The color of metric

(mm) release-ring becomes yellow.*3. EPDM (-E) specification can not be selected for the products with M3 or M6 threads or with inch tube

size.

(4) Lubrication Code -D No code

Specification Oil-free Standard lubrication*1. The metric (mm) size release-ring color of oil-free (-D) specification becomes yellow while inch size is

white.*2. The product with oil-free (-D) specification is assembled without intentional use of lubrication in

standard process. Therefore the problem of reducing airtightness or increasing frictions of rubber parts may be resulted.

(5) Release-ring color Code -R No code

Color Red Standard

(6) Non-purple specification (only for taper threaded product) Code -P No code

Specification Non-purple Standard* Non-purple (-P) specification cannot be combined with FKM (-F) specification.* The color of the release-ring of metric (mm) tube size is brown for non-purple (-P) specification.* No Sealock coating for non-purple specification.

Release-ring color change• Change the color of release-ring to red.

Non-purple specification• Restraining generation of Cu ion or F ion from the product.

* Please be careful at the time of piping of Check Valve, Stop Fitting, etc, which has laser-marking on the plated parts made of brass because the marking is not carried out.

* The color of release-ring of inch tube size is always white.


323

Reference Chart of Special Options○: Selectable, ×: Not selectable

Product

Standard specification Special specification

Outer color,Package

option

Resin body color

Release-ring color

Sealing material Lubrication Thread

sealing

①Resin color

②Sealing material

③Lubrication

④Release-ring color

⑤Non-purple

spec.W*1 –F*2 –E*3 –D*4 –R –P*2

Light-gray FKM EPDM Oil-free spec. Red No sealock coatTube Fitting Standard Series ー Black Black

NBR

Turbine oil

With sealock coat

ー ○*5 ○ ○ ○ ○Light-gray Light-gray Light-gray Std. option ○ ○ ○ × ○

Cleanroom pkg. Light-gray Light blue Fluorochemical grease

ー ○ ○*6 ○*6 × ×Light-gray &

Cleanroom pkg. Light-gray Light-gray Std. option ○ ○ ○ × ×

Tube Fitting Mini Series ー Black Black

NBR

Turbine oil

With sealock coat

ー ○*5 ○ ○ ○ ○Light-gray Light-gray Light-gray Std. option ○ ○ ○ × ○


ー ○ ○*6 ○*6 × ×Light-gray &

Cleanroom pkg. Light-gray Light-gray Std. option ○ ○ ○ × ×

Tube Fitting Stainless SUS304 series ー Black Dark blue FKM Turbine oil With sealock coat × Std. spec. × ○*7 × ×Tube Fitting Stainless SUS303 like corrosivity ー Black Dark blue HNBR Turbine oil With sealock coat ○ ○ ○*7 ○*7 × ○Tube Fitting EG Series ー Black Black NBR Turbine oil With sealock coat × ○ ○*8 × × ○

Tube Fitting Brass Series ーーーHNBRFKMNBR

Turbine oil With sealock coat × Std. option ○ ○ × ○

Tube Fitting Long type ーー Black NBR Turbine oil With sealock coat × ○*5 ○ ○ ○ ○Speed Controller Series ー Black Black

NBR

Turbine oil

With sealock coat

ー ○*5 × × ○ ○Light-gray Light-gray Light-gray Std. option ○ × × × ○


ー ○ × × × ×Light-gray &

Cleanroom pkg. Light-gray Light-gray Std. option ○ × × × ×

Speed Controller SUS303 like corrosivity ー Black Dark blue HNBR Turbine oil With sealock coat ○ ○ × × × ○Throttle Valve Series ー Black Black

NBR

Turbine oil

With sealock coat

ー ○*5 × × ○ ○Light-gray Light-gray Light-gray Std. option ○ × × × ○


ー ○ × × × ×Light-gray &

Cleanroom pkg. Light-gray Light-gray Std. option ○ × × × ×

Fixed orifice joint Series ー Black Black NBR Turbine oil With sealock coat ○ ○ ○ ○ ○*9 ○Regulator (except RVF) ー Black Black NBR Turbine oil With sealock coat ○ × × × ○*9 ○Check Valve (metal body) ー Black Black NBR Turbine oil With sealock coat ○*10 × × × ○*9 ○Check Valve (resin body) ー Light-gray Light-gray NBR Turbine oil With sealock coat Std. spec. × × × × ○*1. If light-gray (W) is selected for resin color, the release-ring color of metric (mm) tube size becomes light-gray even for combination with any other options.*2. FKM (-F) specification of sealing material can not be combined with non-purple (-P) specification.*3. For EPDM (-E) specification of sealing material, the product is assembled as oil-free specification. The color of release-ring of metric (mm) tube size becomes yellow

except the combination with light-gray specification, which has light-gray release-ring. EPDM (-E) specification can not be selected for the products with M3 or M6 threads or inch tube size.

*4. The release-ring color becomes yellow. If it with light-gray specification, the color of release-ring is light-gray.*5. The release-ring color becomes brown.*6. The release-ring color becomes light blue.*7. The release-ring color becomes dark blue.*8. The release-ring color becomes black.*9.The Red release-ring color specification can not be selected if light-gray specification of resin color is selected.

*10. The light-gray specification can not be selected for CVU4-4, CVU6-6, and CVU8-8.


324

Order Production

Reference Chart of Appearance Color Combination with Special Options (Case of Fitting)

Product Resin color or option Tube size Sealing material Lubrication Release-ring color–F –E –D –R

Std. appearance FKM EPDM Oil-free spec. Red

Tube FittingTube Fitting Mini-type

ー

Metric (mm)

Inch

Light-gray spec.

Metric (mm)

Inch

Cleanroom pkg.

Metric (mm)

Inch

Light-gray spec. & Cleanroom pkg.

Metric (mm)

Inch

Tube Fitting Stainless SUS304 series ー Metric (mm) Same as std.

Tube Fitting Stainless SUS303 like corrosivity

ー Metric (mm)

Light-gray spec. Metric (mm)

(No code)

(W)

(C)

(WC)

(W)


325

Reference Chart of Appearance Color Combination with Special Options (Case of Flow Controller)

Product Resin color or option Tube size Sealing material Release-ring color–F –R

Std. appearance FKM Red

Speed ControllerThrottle Valve

ー

Metric (mm)

Inch

Light-gray spec.

Metric (mm)

Inch

Cleanroom pkg.

Metric (mm)

Inch

Light-gray spec. & Cleanroom pkg.

Metric (mm)

Inch

(W)

(C)

(WC)


New Tube Fitting Mini Series C D S I - Trikanditrikandi.com/media/PDF/Pisco Tube Fitting Mini...

Documents

Transcript of New Tube Fitting Mini Series C D S I - Trikanditrikandi.com/media/PDF/Pisco Tube Fitting Mini...