NEW Self-contained New Standard! PR-G · The PR-G Series also offers an easy to adjust trimmer for...
Transcript of NEW Self-contained New Standard! PR-G · The PR-G Series also offers an easy to adjust trimmer for...
PR-GSERIES
NEW Self-containedPhotoelectric Sensor
New Standard!General-Purpose Metal Photoeye
New Standard for Photoelectric Sensors
LR-Z SER
IES
PR-M
/F SERIE
S
PR-G SER
IES
01 02 03
2
PR-GSERIES
Self-containedPhotoelectric Sensor
* See page 11 for details.
Revolutionizing general-purpose photoelectric sensorsIn industrial automation, the large majority of general-purpose photoelectric sensors are made of plastic. While this design is adequate for certain environments, harsher industrial environments require that these sensors be frequently replaced due to damage. By combining a metal housing with reliable detection capabilities, KEYENCE has developed a durable photoelectric sensor that will provide lasting detection in the harshest of environments.
DURABLE & LONG LIFEHigh enclosure rating and Stainless steel body (SUS316L*)
EASE OF USEHighly visible indicator and 7-segment display
HIGH POWERIntegrated 4-element LED
4
High enclosure rating and Stainless steel body (SUS316L*)
DURABLE & LONG LIFE
5
Cause identification
Periodic inspection
Sensor replacement Guarding against recurrence
Significant reduction
KEYENCE requires that all of its photoelectric sensors provide long-term, reliable operation. With a durable stainless steel housing (SUS316L*), the PR-G Series is able to withstand over tightening and impact without the need for additional guarding. The PR-G Series maintains IP68 & IP69K enclosure ratings; while also remaining highly resistant to oils, acids, and alkaline detergents.
Resists damage, even when over-tightened Meets NEMA Type 4X*, 6P*, 13 and IP68/69K requirements
Downtime as a result of sensor damage, compared to normal operation
Downtime
Normal operation
By eliminating downtime due to sensor damage, the amount of normal operation time is greatly increased
* See page 11 for details.
6
The integration of a high luminance 4-element LED with an increase in the gain of the received light intensity, has enabled the PR-G Series thrubeam model to achieve a maximum detecting distance of 30 meters 98.4'. These two factors allow the PR-G Series to reliably detect through oil, dust, and other forms of build-up. This high power ensures the stable operation of the PR-G Series in harsh environments.
HIGH POWERIntegrated 4-element LED
30 m 98.4'max.
7
The large output indicator is clearly visible from any position and is approximately six times larger than that of a conventional KEYENCE sensor. The PR-G Series also offers an easy to adjust trimmer for simplistic sensitivity setting (no special tools required). Along with this, the reflective and retro-reflective models contain a 7-segment digital display, which enables accurate calibration based on numerical values.
EASE OF USEHighly visible indicator and 7-segment display
Highly visible indicator (Approx. 6 times larger than conventional KEYENCE models)
Easily adjust sensitivity while monitoring numeric values
8
❚ Lineup
*1 Cable sold separately.*2 Reflector sold separately. Reflectors and corresponding detecting distances can be found on page 9.
Configuration Type Detecting distance Connection Method Output Model Weight
Thrubeam
M18 threaded mount w/ M12 connector
30 m 98.4'
M12 4-pin*1 Bipolar(NPN + PNP)
PR-G51CBD Approx. 85 g
Rectangular w/ 2 m 6.6' cable
2 m 6.6' cable
NPN PR-G51N
Approx. 160 g
PNP PR-G51P
Rectangular w/ M8 connector
M8 4-pin*1
NPN PR-G51CN
Approx. 55 gPNP
PR-G51CP
M8 3-pin*1 PR-G51C3PD
Retro-reflective*2
M18 threaded mount w/ M12 connector
0.1 to 4.2 m 0.3' to 13.8'* When OP-84219 (R-2L) is used
M12 4-pin*1 Bipolar(NPN + PNP)
PR-G61CBD Approx. 45 g
Rectangular w/ 2 m 6.6' cable
2 m 6.6' cable
NPN PR-G61N
Approx. 75 g
PNP PR-G61P
Rectangular w/ M8 connector
M8 4-pin*1
PNP
PR-G61CP
Approx. 25 g
M8 3-pin*1 PR-G61C3PD
Reflective
M18 threaded mount w/ M12 connector
500 mm 19.69"
M12 4-pin*1 Bipolar(NPN + PNP)
PR-G41CBL Approx. 45 g
Rectangular w/ 2 m 6.6' cable
2 m 6.6' cable NPN PR-G41N Approx. 75 g
Rectangular w/ M8 connector M8 4-pin*1 PNP PR-G41CP Approx. 25 g
Screw length
9
Type Model Material/Weight
Standard mounting bracket for rectangular type(M3 screw x 2 supplied)
OP-87408*1*2 SUS316LApprox. 30 g
Rear mounting bracket for rectangular type(M3 screw x 2 supplied)
OP-87409*2 SUS316LApprox. 30 g
Robust mounting bracket for rectangular type (t = 3 0.12")(M3 screw x 2 supplied)
OP-87410*2*3 SUS316LApprox. 170 g
Adjustable bracket for rectangular type(M3 screw x 2 supplied)
OP-87404Zinc nickel plating
and othersApprox. 95 g
Adjustable bracket for threaded mount type
OP-87405Zinc nickel plating
and othersApprox. 100 g
Adjustable bracket fixing screw
Screw length: 45 mm1.77"
OP-87406 Steel nickel platingApprox. 70 g
Screw length: 65 mm2.56"
OP-87407 Steel nickel platingApprox. 80 g
Extendable bracket for rectangular type
OP-87664Zinc nickel plating
and othersApprox. 190 g
Extender arm for rectangular type(M3 screw x 4 and plate nut x 1 supplied)
200 mm7.87"
OP-87665*2 SUS304Approx. 77 g
130 mm5.12"
OP-87666*2 SUS304Approx. 50 g
M18 nut OP-3052*4 Brass nickel platingApprox. 10 g
M18 Lock washer OP-2263*4
Material: SteelSurface treatment: Trivalent
chromium platingApprox. 5 g
Adjustable bracket for rectangular type
Adjustable bracket for threaded mount type
❚ Mounting bracket
*1 This bracket is dedicated to the cable type sensors. Use OP-87409 or OP-87410 when using the connector type sensors.
*2 These brackets are only meant for use with the rectangular type sensors.*3 When installing a connector type sensor in this bracket, an L-shaped connector cable
must be used.*4 Supplied with M18 threaded mount type.
❚ Reflector
Extendable bracket for rectangular type
OP-87407 + 87664 + 87666 OP-87406 + 87404 OP-87406 + 87405
Type Model Detecting distance
Reflective Area
Temperature specification Material /Weight
Reflective mirrorR-2L
OP-84219
0.1 to 4.2 m0.3' to 13.8'
47 x 47 mm1.85" x 1.85"
−20 to +50°C-4 to 122°F
Reflector: AcrylicBase: ABS
Approx. 20 g
Reflective mirrorR-3
OP-96436
0.1 to 2.9 m0.3' to
9.5'
31 x 31 mm1.22" x 1.22"
Reflector: AcrylicBase: ABS
Approx. 10 g
Reflective mirrorR-5
R-5
0.1 to 2.5 m0.3' to 8.2'
34 x 11.6 mm
1.34" x 0.46"
Reflector: AcrylicBase: ABS
Approx. 5 g
Reflective tape
OP-84221
0.2 to 1.1 m0.7' to 3.6'
30 x 40 mm1.18" x 1.57"
Surface: AcrylicCube: Polycarbonate
Approx. 1 g
Oil/Chemical-resistantreflector
OP-87623
0.1 to 2.4 m0.3' to 7.9'
51 x 51 mm 2.01" x 2.01"
−20 to +70°C-4 to 158°F
Oil/Chemical-resistant resinApprox. 20 g
Roundreflector
OP-87624
0.1 to 3 m
0.3' to 9.8'
ø80 ø3.15" exclude
ø10.5 ø0.41"in the middle
−20 to +50°C-4 to 122°F
Reflector: AcrylicBase: ABS
35 g
Black/�
White/�
Blue/�
Output 1
Output 2
0 V
10-30 VDC
Load
Ove
rcur
rent
prot
ectio
n ci
rcui
t
Sens
or m
ain
circ
uit
Brown/�
Load
Brown/�
Black/�
White/�
Blue/�
Output 1
Output 2
0 V
10-30 VDC
Load
LoadOve
rcur
rent
prot
ectio
n ci
rcui
t
Sens
or m
ain
circ
uit
Brown/�
Black/�
Blue/�0 V
10-30 VDC
Emission stop input
Short-circuit current: 1 mA max.
5 VDC
Sens
or m
ain
circ
uit
342
1
34
1
34
21Se
nsor
mai
n ci
rcui
t Load
Load
Over
curr
ent p
rote
ctio
n ci
rcui
t
10-30 VDC
0 V
Brown/�
Black/�
White/�
Blue/�
10
❚ Cable
❚ Enclosure ratings
Enclosure rating
Connector typeCable type
Standard Oil-resistant
Chemical-resistant
IP67IEC60529
✓ ✓ ✓ ✓
IP68IEC60529
– ✓ ✓ ✓
IP69KDIN40050-9
– ✓*1
✓ ✓
ECOLAB,
Diversey– – ✓
*2✓
*2
❚ I/O circuit diagram
Bipolar Thrubeam transmitter
M8 connector(4-pin)
type
M8 connector(3-pin)
type
M12 connector(4-pin)
type
PNPNPN
*1 Only the M12 connector type satisfies this specification.*2 Tested for endurance against cleaners of several
companies.
Specifications Material Appearance Connection Method Length Model Weight
Standard Cable: PVC Connector: Zinc nickel plating
Straight type
M12 4-pin2 m 6.6' OP-87634 Approx. 100 g
10 m 32.8' OP-87635 Approx. 430 g
M8 4-pin2 m 6.6' OP-87625 Approx. 75 g
10 m 32.8' OP-87626 Approx. 340 g
M8 3-pin 2 m 6.6' OP-87627 Approx. 80 g
Oil-resistant Cable: PUR Connector: Zinc nickel plating
M12 4-pin2 m 6.6' OP-87636 Approx. 75 g
10 m 32.8' OP-87637 Approx. 330 g
M8 4-pin2 m 6.6' OP-87628 Approx. 55 g
10 m 32.8' OP-87629 Approx. 260 g
Chemical-resistant Cable: PVC Connector: SUS316L
M8 4-pin 2 m 6.6' OP-87621 Approx. 75 g
M8 3-pin 2 m 6.6' OP-87622 Approx. 65 g
Standard Cable: PVCConnector: Zinc nickel plating
L-shaped type
M12 4-pin2 m 6.6' OP-87638 Approx. 100 g
10 m 32.8' OP-87639 Approx. 430 g
M8 4-pin 2 m 6.6' OP-87630 Approx. 75 g
M8 3-pin 2 m 6.6' OP-87631 Approx. 65 g
Oil-resistant Cable: PURConnector: Zinc nickel plating
M12 4-pin2 m 6.6' OP-87640 Approx. 75 g
10 m 32.8' OP-87641 Approx. 330 g
M8 4-pin2 m 6.6' OP-87632 Approx. 55 g
10 m 32.8' OP-87633 Approx. 260 g
Chemical-resistant Cable: PVCConnector: SUS316L
M8 4-pin 2 m 6.6' OP-87619 Approx. 70 g
M8 3-pin 2 m 6.6' OP-87620 Approx. 60 g
11
*1 For the threaded mount type sensors, the outputs are 1 NPN output and 1 PNP output.*2 Output 2 is not available on the threaded mount type or M8 3-pin type.*3 For the connector type, the enclosure rating varies depending on the cable that is used. *4 When the ambient temperature is 60°C 140°F or higher, the device should be powered with no more than 24 VDC and 50 mA.
❚ Specifications
Type Thrubeam Retro-reflective Diffuse reflective
Model
Threaded mount type
NPN + PNP(Bipolar)
M12 connector, 4-pin
PR-G51CBD PR-G61CBD PR-G41CBL
Rectangular type
NPN2 m 6.6' cable PR-G51N PR-G61N PR-G41N
M8 connector, 4-pin PR-G51CN — —
PNP2 m 6.6' cable PR-G51P PR-G61P —M8 connector, 4-pin PR-G51CP PR-G61CP PR-G41CP
M8 connector, 3-pin PR-G51C3PD PR-G61C3PD —Detecting distance 30 m 98.4' 0.1 to 4.2 m 0.3' to 13.8' 500 mm 19.69"No. of control outputs 2 (Dark-ON + Light-ON)*1
Output operationOutput 1 Dark-ON Light-ONOutput 2*2 Light-ON Dark-ON
Response time 1 ms 0.5 msSensitivity adjustment One-turn trimmer (230°) Five-turn trimmer
Spot diameter — ø20 mm ø0.79" max.(at 300 mm 11.81")
Light source 4 elements, Red LED(631 nm)
4 elements, Red LED(630 nm)
4 elements, Point light source red LED(650 nm)
Mutual interference prevention — 2 units
IndicatorsTransmitter: Power indicator (green)Receiver: Output indicator (yellow), Stable operation indicator (green)
7-segment display (0 to 999), Output indicator (yellow)
Power voltage 10 to 30 VDC, including 10% ripple (P-P)
Power consumption
Transmitter: 450 mW max. (15 mA max. at 24 V, 15 mA max. at 12 V)
Receiver: 360 mW max. (12 mA max. at 24 V, 15 mA max. at 12 V)
450 mW max. (15 mA max. at 24 V, 21 mA max. at 12 V)
Control outputNPN output type: NPN open collector, PNP output type: PNP open collector, Bipolar output type: NPN + PNP open collector
30 VDC or less, 100 mA or lessResidual voltage: 1.2 V or less at less than 10 mA, 2 V or less at 10 to 100 mA
Emission stop inputNon-voltage input
Input time ON: 1 ms or more, OFF: 20 ms or more
—
Protection circuit Protection against reverse power connection, power supply surge, output overcurrent, output surge, and reverse output connection
Environmental resistance
Enclosure rating* 3 IP68 (IEC60529), IP69K (DIN40050-9), Rectangular type: 4X, 6P, 13 (NEMA250), Threaded mount type: 4, 6, 13 (NEMA250)
Ambient light Incandescent lamp: 5000 lux or less, Sunlight: 20000 lux or lessAmbient temperature -20 to +70°C -4 to 158°F (No freezing)*4
Storage temperature -20 to +70°C -4 to 158°FAmbient humidity 35 to 85% RH (No condensation)Shock resistance 1000 m 3280.8'/s2 in X, Y, and Z directions, 6 times respectivelyVibration resistance 10 to 55 Hz, 1.5 mm 0.06" double amplitude in X, Y, and Z directions, 2 hours respectivelyInsulating resistance 20 MΩ or more (500 VDC)Withstand voltage 1000 VAC, 50/60 Hz, 1 min
Material
Case: Rectangular type: SUS316L, Threaded mount type: Zinc die cast (Nickel chrome plating), Indicator cover: PES,
7-segment display cover/Lens cover: PMMA (scratch-resistant coating)M18 nut: Brass (Nickel plating),
Lock washer: Steel (Chrome plating)
WeightM12 connector Approx. 85 g Approx. 45 g2 m 6.6' cable Approx. 160 g Approx. 75 gM8 connector Approx. 55 g Approx. 25 g
Accompanying items Instruction Manual, (Threaded mount type only) M18 nut, Lock washer
10.8
15.5
3.8
3.3
5
21
32.1
8
33.9 25.4
ø10ø0.39"
9.9
3
12.7
19.7
2 × M3, P = 0.5
2.8
5.8
Indicator
Sensitivity adjustment trimmer
DisplayCenter of received light
Center of emitted light M8 connector
0.50"
0.23"
0.78"
1.26"
0.31"
0.39"
0.83"
0.12"
1.0"1.33"
0.11"
0.61"
0.43"
0.13"
0.15"
0.20"
0.50"
0.23"
0.78"
1.26"
0.83"
0.12"
1.0"1.33"
0.11"
0.61"
0.43"
0.13"
0.15"
2 × M3, P = 0.510.8
3.8
3.3
15.5
32.1
21
25.433.9
3
19.7
5.8
12.7
2.8
Indicator
Sensitivity adjustment trimmer
DisplayCenter of received light
Center of emitted light
ø4 ø0.16", 4 cores x Brown/Blue/Black/White: 0.2 mm2
Cable length: 2 m 6.6'
5
21
8
ø10ø0.39"
0.31"
9.90.39"3
12.7
2.8
2 × M3,P = 0.5
Center of emitted/received light
Indicator
Sensitivity adjustment trimmer
(Receiver only)
M8 connector
0.50"
32.1*
*32.0 1.26" for transmitter
0.83"
1.26"
0.12"0.11"
25.433.91.0"1.33"
10.8
15.50.61"
0.20"
0.43"2 × M3,P = 0.5
10.8
15.5
32.1*
21
25.433.9
3
12.7
2.8
Center of emitted/received light
Indicator
Sensitivity adjustment trimmer
(Receiver only)
[Transmitter] ø3.9 ø0.15", 3 cores x Brown/Blue/Black: 0.34 mm2
[Receiver] ø4 ø0.16", 4 cores x Brown/Blue/Black/White: 0.2 mm2
Cable length: 2 m 6.6'
*32.0 1.26" for transmitter
0.50"
0.83"
1.26"1.0"
0.12"0.11"
1.33"
0.61"
0.43"
12.8
30.59.58
3.5
3
12
ø13.6
12.5
32.1
15.4
3.8
3.3
M12 connector
Sensitivity adjustment trimmer
Indicator
Display
Transmitting point
Receiving point
2 x ø3.2
M18, P = 1.0 6.5
17
0.13"
0.15"
ø0.54"
0.26"
0.67"
0.12"
0.47"
ø0.13"
0.37"0.31"
0.61" 1.20"
0.50"
0.49"
1.26"
0.14"
1.33"
0.61"
0.95"15.5
33.9 24.1
12.8 0.50"
1.20"0.61"0.37"
0.31"
1.33"
0.61"
0.95"
0.14" 0.12"0.47"
ø0.54"
0.49"
1.26"
ø0.13"
30.59.58
312
ø13.6
12.5
32.1
15.4
15.5
M12 connector
Sensitivity adjustment trimmer(Receiver only)
Indicator
2 x ø3.2
M18, P = 1.0
33.9 24.1
3.5
Center of emitted/received light
12
PR-G51N/G51P
PR-G41N/G61N/G61P
PR-G41CBL/G61CBDPR-G51CBD
PR-G41CP/G61CP/G61C3PD
PR-G51CN/G51CP/G51C3PD
❚ Dimensions
1.14"0.31"
0.20"0.43"
0.14"
1.83"
0.65"0.74"
1.19"
0.64"0.14"
0.16"
0.14"
0.14"
0.71"0.28"0.28"
1.00"
SUS316Lt = 2.0 0.08"
18.8
25.4
16.3
30.2
3.5
8° 3°
(R)
16.5
4 7187
5
29
11
3.5(R)
(R)
R25.4 R1.00"
(R)
46.5
7.75
3.5
2 × R2 R0.08"
2 × R2 R0.08" R25.4
R1.0"
3.5
16.5
1017.6
4°10°
13
3843
518.4
16
30
(R)
6.8(R)
79
6.4
22.540.9
21
4 × R2 R0.08"
2 × R2 R0.08"
21.6
3.3
2 x ø3.5 ø0.14"
783.5
R25.4R
1.0"
SUS316Lt = 3.0 0.12"
1.69"1.5"0.83"
0.89"1.61"
0.25"0.27"1.18"
0.51"0.13"
0.39"0.69"
3.11"
0.65"
3.07"0.14"
0.72" 0.20"
0.63"
0.85"
R25.4 R1.0"
25.4 5.5
26.5
3.5 0.14"
3.50.14"
(R)
16.5
36
718
412
5
34
10
3.5(R)
(R)
(R)
7.75
3.5
2 × R2 R0.08"
R25.4R1.0"
SUS316Lt = 2.0 0.08"
5°
4°
1.34"
0.39"
0.14"
0.22"
1.42"
0.65"
1.04"
0.71" 0.47"0.16" 0.28"
2 × R2 R0.08"
0.31"
0.20"
0.14"
1.0"
(3)
82 × ø3.5 ø0.14"
3.5
(70)
L
24.5 1 15
2
3.5
175
25.4
5
L = 200 mm 7.87": OP-87665L = 130 mm 5.12": OP-87666
ø12 ø0.47"
ø9 ø0.
35"
0.67"0.20" 0.14"
1.0"0.59"
0.08"0.14"
0.31"
0.04"0.96"
(2.76")
(0.12")
0.20"
19.5
12.5
180.71"0.77"
0.49"
8.3 5
1525.435.9
13.5
12
16
21.5
26.7 4 × ø3.5 ø0.14"
L
L = 50 mm 1.97": OP-87406L = 70 mm 2.76": OP-87407
1.05" 0.33" 0.20"
1.41" 1.0"
0.47"
0.85" 0.53"
0.63"
0.59"
47.5
ø27
54.5
35
19.5
12.5
(ø12)
(ø12) (ø0.47")
(ø0.47")
ø1.06"
1.38"0.49" 1.87"
2.15"0.77"
Hexagon socket head cap screw(M5, Length: 15 mm 0.59", Across-flats: 4 mm 0.16", Iron nickel plating)
Nut (M5, Iron nickel plating)
Brass nickel plating
Nickel-plated zinc die cast
10 L
(32)(1.26")
M10 × P1.52 × ø21 ø0.83", Thickness: 2 0.08"
Across-flats: 17 0.67", Thickness: 8 0.31"
Iron nickel platingL = 45 mm 1.77": OP-87406L = 65 mm 2.56": OP-87407
ø16ø0.63"
0.39"
19.5
12.5
18
8.3 5
1525.435.9
13.5
12
16
21.5
26.7
(ø12)
4 × ø3.5 ø0.14"
SUS430
(27)
Nickel-plated zinc die cast
Nut (M5, Iron nickel plating)
Hexagon socket head cap screw(M5, Length: 15 mm 0.59", Across-flats: 4 mm 0.16", Iron nickel plating)
(1.06")
(ø0.47")
0.33"
1.05"
0.20"
1.41" 1.00" 0.59"
0.49"
0.77" 0.71"
0.47"
0.85" 0.53"
0.63"
13
OP-87408 OP-87404
OP-87409
OP-87410 OP-87665/87666OP-87664
OP-87406/87407
OP-87406 (87407) + OP-87404
Unit: mm inch
3.5
8
2 × ø4.5 ø0.18"
5.53040
47
4761
51.2
51.2
25.6
30.4
1.85"
1.85"2.4"
1.01"
1.20"
2.02"
0.14"1.18"1.57"2.02"
0.22"
0.31"
t = 0.7 0.03"
301.18"
40 1.57"
31
3117.5
35
2142
152535
3.55.5
8
2 × ø3.6 ø0.14"
1.22"
0.83"
1.38"
0.14"0.22"
0.31"
0.69"
1.65"
0.59"0.98"1.38"
1.22"
2 × M3
14 11.511.6
36 34
3
25.4
2.6
0.55"0.46"
0.45"
1.00"
0.12"
0.10"
1.34"1.42"
3.55.2
30.3
4.3
7.5
61
51
10 20
51
14.1
2.01"
2.01"2.4"
0.17"
0.56"0.39" 0.79"
1.19"
0.20"
0.14"
0.3"
ø84 ø3.31"
7.30.29"
ø4.5 ø0.18" mounting holeSpot facing: ø7.4 ø0.29"Depth: 4.9 0.19"
ø14.7ø0.58"
44 OP-87634: 2000 78.74" / OP-87635: 10000 393.7"1.73"
ø5.2 ø0.20" (4 x 0.34 mm2)
M12
OP-87636: 2000 78.74" / OP-87637: 10000 393.7"44
ø14.7
1.73"
ø0.58"
ø4.7 ø0.19" (4 x 0.34 mm2)
M12
8°
34.51.36"
27.41.08"
ø14.8 ø0.58"
OP-87638: 2000 78.74" / OP-87639: 10000 393.7"
ø5.2 ø0.20" (4 x 0.34 mm2)
M12
Zinc die-casting
ø27ø1.06" ø0.87"
0.13"
36.8
ø12 ø0.47"
8.3
Nut (M5, Steel nickel plating)
Hexagon socket head cap screw(M5, Length: 15 mm 0.59", Width across flat: 4 mm 0.16", Steel nickel plating)
12.5 4.33.3
19.5
3.217.4
0.69"ø22
1.45"
0.33"
0.49"
0.13"0.17"
0.77"
37.5
23.5
37
ø20 ø
0.79"
R13.5
R0.53"
R14 R0.55"
ø18.5 ø0.73"
14
51
20
34
SUS304t = 3.0 0.12"
0.55"
2.01"
1.48"
1.46"
0.79"0.93"
1.34"
Brass nickel plating24 4
M18 x P1.0
0.94" 0.16"SteelTrivalent chromium plating
2.4
ø29ø19ø1.14"ø0.75"
0.09"
OP-87640: 2000 78.74" / OP-87641: 10000 393.7"8°
34.5
27.4
1.36"
1.08"
ø14.8 ø0.58"
ø4.7 ø0.19" (4 x 0.34 mm2)
M12
14
OP-84219 (R-2L)
OP-87623
OP-96436 (R-3)
OP-87624
OP-84221 (Reflective tape)
R-5
OP-87634/87635
OP-87636/87637 OP-87640/87641
OP-87638/87639
OP-87405
OP-3052 OP-2263
32 2000 78.74"
ø4.7 ø0.19" (4 × 0.25 mm2)
ø10
M8(4pin)
ø0.39"
1.26"
33.7 1.33"
ø0.39"
OP-87625: 2000 78.74" / OP-87626: 10000 393.7"
ø10
ø4.7 ø0.19" (4 × 0.25 mm2)
M8(4pin)
M8(4pin)
ø4.7 ø0.19" (4 × 0.25 mm2)
ø105°
18.90.74"
27.91.10"
2000 78.74"
ø0.39"
ø10 ø0.39"
18.90.74"
27.91.10"
M8(4pin)
ø4.4 ø0.17" (4 × 0.25 mm2)
OP-87632: 2000 78.74" / OP-87633: 10000 393.7"5°
No. Color
4
1
2
3
Black
Brown
White
Blue
2000 78.74"0.98"
0.79"ø4.7 ø0.19" (4 × 0.25 mm2)
25
20
ø10ø0.39"
M8(4pin)
200025
20ø4.4 ø0.17" (3 × 0.25 mm2)
ø10
78.74"0.98"
0.79"
ø0.39"M8(3pin)
ø4.4 ø0.17" (3 × 0.25 mm2)
33.7
ø10
2000M8(3pin)
78.74"1.33"
ø0.39"
32 2000
ø4.4 ø0.17" (3 × 0.25 mm2)
ø10
M8(3pin)
78.74"1.26"
ø0.39"
ø10
ø4.4 ø0.17" (3 × 0.25 mm2)
18.90.74"
27.91.10"
20005°
M8(3pin) 78.74"
ø0.39"
2
41 3
1
34
12
34
ø4.4 ø0.17" (4 × 0.25 mm2)
OP-87628: 2000 78.74" / OP-87629: 10000 393.7"M8
(4pin)
33.7 1.33"
ø0.39"ø10
15
OP-87625/87626 OP-87630
OP-87632/87633
OP-87627 OP-87631
OP-87628/87629
OP-87621 OP-87619
OP-87622 OP-87620
M12 connector(4-pin)type
M8 connector(4-pin)type
M8 connector(3-pin)type CAD DATA DOWNLOAD
www.keyence.com/CADG
Unit: mm inch
KA210-1013
Copyright (c) 2013 KEYENCE CORPORATION. All rights reserved. PRG-KA-C-US 1033-1 611718 Printed in Japan
KEYENCE CORPORATION OF AMERICASales & Marketing Head Office 1100 North Arlington Heights Road, Suite 350, Itasca, IL 60143 PHONE: 888-539-3623 FAX: 630-285-1316
SAFETY INFORMATIONPlease read the instruction manual carefully in order to safely operate any KEYENCE product.
The information in this publication is based on KEYENCE’s internal research/evaluation at the time of release and is subject to change without notice.
1 - 8 8 8 - 5 3 9 - 3 6 2 31-888-KEYENCE
CALL TOLL FREE
T O C O N TA C T Y O U R L O C A L O F F I C E www.keyence.comE-mail : [email protected]
* 6 1 1 7 1 8 *
PR-GSelf-containedPhotoelectric Sensor
LR-ZSERIES
Self-containedCMOS Laser Sensor
PR-M/FSERIES SERIES
Self-contained Miniature Photoelectric Sensor
PZ-G/VSelf-Contained Photoelectric Sensor
SERIES