Network Master Pro/Flex Release...
Transcript of Network Master Pro/Flex Release...
Network Master Pro/Flex Release Notes
1 TAA-1ETNMX0054-47
2020-08-11 Anritsu Corporation
Network Master Pro/Flex Release Notes
Product Configuration
The following table shows the relationship between the changed application and modules described in the
Revision History.
Main frame Module Changed Application
MT1100A/MT1000A
Common
― [Framework][Remote]
MT1100A MU110010A
MU110011A
MU110012A
MU100013A
[ETH][OTN][CPRI][FC][SDH/SONET][SDHPDH][GPS][MxH]
MT1000A MU100010A
MU100090A
MU100020A
MU100021A
MU100022A
MU100023A
[OTDR][FTTA][OLTS]
MU100040A
MU100040B
[CPRI-RF]
Network Master Pro/Flex Release Notes
2 TAA-1ETNMX0054-47
Latest Installer File Name
MT1000A MT1100A
10.03.MT1000A_SW
10.03.MU100011A_DATA
MX100001A-Setup-10.03-xxxxx.exe
MX100003A-2.0.0.55-xxxxx.exe
10.03.MT1100A_SW
MX100001A-Setup-10.03-xxxxx.exe
MX100003A-2.0.0.55-xxxxx.exe
The following table shows the latest software and corresponding operation manuals.
Operation Manual Doc. No. MT1000A MT1100A
MT1000A Network Master Pro
MT1100A Network Master Flex
Remote Scripting Operation Manual
M-W3736AE 27th 27
th
MT1000A Network Master Pro Transport modules
Operation Manual
M-W3933AE
15th
-
MT1100A Network Master Flex Operation Manual M-W3735AE - 28th
MT1000A Network Master Pro OTDR Modules
Operation Manual
M-W3810AE
17th -
MT1000A Network Master Pro OTDR Modules
Remote Scripting Operation Manual
M-W3859AE 6th
MX100003A Scenario Edit Environment Kit Operation
Manual
M-W4042AE 1st 1
st
MT1000A MU100040A/MU100040B Network Master
Pro Operation Manual
10580-00443 A -
Network Master Pro/Flex Release Notes
3 TAA-1ETNMX0054-47
The Relation Between Software and Operation Manuals
MX100003A
Version
Related MX100003A
Operation Manual Edition
Working MT1000A/MT1100A
Firmware Version
2.00.55 1.0
Title Changed1
10.02 to 10.03
2.0.0.54 13.0 10.02 to 10.03
2.0.0.53 13.0 10.00 to 10.01
2.0.0.52 12.0 9.09 to 9.13
2.0.0.51 11.0 9.07 to 9.08
2.0.0.36/43/45/48/49/50 5.0 to 10.0 5.04 to 9.06
2.0.0.23 4.0 5.04 to 7.04
1.0.0.76 2.0 to 3.0 5.04 to 7.01
1.0.0.72 1.0 5.04
1 The title changed from “MX100003A MT1000A/MT1100A Scenario Edit Environment Kit Operation
Manual” to “MX100003A Scenario Edit Environment Kit Operation Manual”.
MT1000A/MT1100A
Firmware
Version
Related Operation Manual Edition
MT1000A MT1100A
MU10001xA
(Transport)
MU100040A/B
(CPRI-RF)
MU10002xA
(OTDR)
MU11001xA
(Transport)
10.03 15 A 17 28
10.02 14 A 16 27
10.01 13 A 15 26
10.00 13 A 15 26
9.13 13 A 14 26
9.12 12 A 13 26
9.11 11 A 12 25
9.10 10 A 11 25
9.09 9 A 11 24
9.08 8 A 10 23
9.07 8 A 10 22
9.06 7 A 10 21
9.05 6 A 10 20
9.04 5 A 10 19
9.03 5 A 10 19
9.02 5 A 9 19
Network Master Pro/Flex Release Notes
4 TAA-1ETNMX0054-47
9.01 5 A 9 19
9.00 4 A
Title Changed2
9 18
8.02 3 A 9 17
8.01 2 A 9 16
8.00 1
Title Changed3
A 8 -
7.05 15 A 7 15
7.04 14 A 6 13
7.03 14 A 6 13
7.02 13 A 5 12
7.01 12 A 5 10
7.00 12 A 5 10
6.02 11 - 4 10
6.01 11 - 4 10
6.00 11 - 4 10
5.04 10 - 3 9
5.03 10 - 3 9
5.02 10 - 3 9
5.01 10 - 3 9
5.00 9 - 2 8
4.00 8 - 1 7
3.04 8 - - 7
3.03 8 - - 7
3.02 7 - - 6
3.01 6 - - 5
3.00 5 - - 4
2.05 4 - - 4
2.04 4 - - 3
2.03 3 - - 2
2.02 2 - - 2
2.01 2 - - 2
2.00 2 - - 1
1.00 1 - - 1
2 The title changed from “MT1000A MU100040A Network Master Pro Operation Manual” to “MT1000A
MU100040A/MU100040B Network Master Pro Operation Manual”. 3 The title changed from “MT1000A MU100010A Network Master Pro Operation Manual” to “MT1000A
Transport Modules Operation Manual”.
Network Master Pro/Flex Release Notes
5 TAA-1ETNMX0054-47
Installation Procedure
1. When using battery, make sure that there is 40% (or more) power in the battery of the instrument.
2. Remove the USB memory from the MT1000A/MT1100A.
3. Press the power button to shut down the MT1000A/MT1100A. Never force to power off by holding the
power button pressed for several seconds.
4. Remove the AC adapter or cable and see the power button turns to gray.
5. Copy the installer (X.XX.MT1000_SW, X.XX.MU100011A_DATAor X.XX.MT1100_SW) to an empty
USB memory stick formatted to FAT32.
6. Insert the USB memory stick into MT1000A/MT1100A.
7. Boot MT1000A/MT1100A to start installer.
The instrument will detect the USB stick, and start installing the software. After the installation has
finished the instrument will reboot and start with the new software.
When installing MT1000A software which includes MU100011A, the installation of MU100011A data
starts automatically at the Network Master rebooting.
8. Remove USB stick after installation is complete
You can check the installed version at System Information screen.
Network Master Pro/Flex Release Notes
6 TAA-1ETNMX0054-47
Installation Procedure via network.
1. When using battery, make sure that there is 40% (or more) power in the battery of the instrument.
2. Install the Control Software(MX100001A) on your PC.
(Please refer “3.5.1 Installation of Control Software” on MT1000A Transport Modules Operation
Manual or MT1100A Network Master Flex Operation Manual.)
3. Configure the Ethernet communication between the Control Software(MX100001A) and
MT1000A/MT1100A. (Please refer “3.5.2 Connection and Setup” on MT1000A Transport Modules
Operation Manual or MT1100A Network Master Flex Operation Manual.)Select the update tab on
Control Software to show the upgrading box.
4. Touch Select File to launch the dialog box.
5. Select the software file. Progress bar shows Upload Progress. Touching Cancel aborts the file
uploading.
6. After file uploading finishes, touch Start Installation.
Touching Start Installation will reboot the Network Master. Installation process cannot be remotely
monitored. Please reconnect after several minutes.
Network Master Pro/Flex Release Notes
7 TAA-1ETNMX0054-47
SEEK Scenario
After installing the software, a set of SEEK scenario is copied in the “/Internal/windowsinstaller/ scenario”
folder. Register the scenario to use it. Refer to the “4.2.1 Registering the Scenario” in the Scenario Edit
Environment Kit Operation Manual.
Scenario Name Description Module
xCVRQuickCheck_03.obcfg This scenario quickly checks optical modules..
Refer to the
“Optical Transceiver Simple Check xCVR Quick Check
SEEK Scenario” on Anritsu WEB Site.
MT1000A
MU100010A
MU100011A
xCVRQuickCheck_00.obcfg MT1100A
MU110013A
Network Master Pro/Flex Release Notes
8 TAA-1ETNMX0054-47
Revision History
Version Date Description
10.03 2020-08-11 Key Added Features
[SEEK] Added support for MT1040A.
2020-07-13 Key Added Features
[ETH] Added following functions to RFC2544. (12697)
- Added Latency, Jitter, Throughput Pass/Fail threshold value
- Added Latency, Jitter, Throughput Pass/Fail threshold value
- Support for simultaneous Latency and Packet Jitter
measurement
[ETH] Improved Latency and Packet Jitter measurement
accuracy at RFC2544 and SAT (Y.1564) measurement. (13550)
[OTDR] Added Korean language GUI descriptions. (12847)
Fixed bugs
[MxH] Fixed bug causing incrementing PRBS sync alarm when
executing communications test while either IEEE1588 or SyncE
set to ON at eCPRI test. (12368)
[ETH] Fixed bug preventing multicast VLAN support for
IEEE1588v2 SMPTE profile. (13485, 13472)
[OTDR] Fixed bug causing slow measurement start after
switching wavelength when wavelength set to ALL at Separate
(Individual) measurement mode setting. (12894)
[OTDR] Fixed bug at transmission loss Pass/Fail evaluation
when Pass/Fail evaluation reference set to ISO/IEC or JIS.
(13537)
10.02 2020-06-04 Key Added Features
Added support for MX109020A Site Over Remote Access;
installing MT1000A-011 option enables remote control and file
access using MX109020A. (13368)
[VIP] Added support for selection of all G0382A option tips.
(13332)
[VIP] Added message display when pass/fail analysis results
range off screen edge. (13333)
Fixed bugs
[ETH] Fixed bug causing one lost Frame at RFC2544
measurement using two MT1000A units with MT1000A
operating as Reflector; bug occurs only with 100, 40, and
25GbE interfaces. (12833)
Network Master Pro/Flex Release Notes
9 TAA-1ETNMX0054-47
[ETH] Fixed bug causing crash when changing [Line load] unit
at 25GbE setting of RFC2544 application. (12939)
[ETH][MxH] Fixed bug causing incorrect detection of PRBS
sync alarm when connecting/disconnecting cable during BER
measurement using cross PRBS pattern at 25GbE or faster
interface. (12594)
[ETH] Fixed bug causing forced restart when outputting
Statistics as .csv file after measuring interval length with [No
Interval] set at Ethernet application. (12820)
[ETH] Fixed bug sometimes causing output of incorrect packet
when sending packets with Frame Size set to [Step] at 25GbE
or faster interface. (12864)
[VIP] Fixed bug preventing normal autofocus operation with
some tips. (13326)
10.01 2020-05-11 Fixed bugs
[ETH][MxH] Fixed bugs when receiving Ping packet of 2048
bytes or more at 25, 40, and 100GbE interfaces. (13380)
- [ETH][MxH] Sometimes no response to Ping request
- [Ping] Sometimes unable to measure at applicable
conditions
- [RFC2544] Sometimes unable to measure when performing
[Router Latency Test] at applicable conditions
10.00 2020-02-20 Key Added Features
[New HW] Added new MU100023A OTDR 1.31/1.55/1.65-um
SMF module to product line.
[OTDR] Added “Launch Length Correlation” and “Receive
Length Correlation” items to Patch Cord settings.
[OTDR] Added 200 ns Pulse Width to 0.5 km Distance Range.
[OTDR] Added function for batch creation of reports (pdf, xml, or
csv) using “.sor” file data saved in built-in or USB memory;
function enabled only at Standard OTDR and FTTA
applications.
[OTDR] Added function for outputting loss table results (pdf,
xml, or csv) at OLTS application.
[OTDR] Improved splitter detection accuracy at
auto-measurement.
[OTDR] Added SCPI command remote control function at OLTS
application.
Network Master Pro/Flex Release Notes
10 TAA-1ETNMX0054-47
[SEEK] Added support for outputting each application
measurement result as one report (pdf, xml, or csv) for
measurement sequence including several applications.
[SEEK] Added function for describing scenarios such as branch
conditions based on information loaded from data described in
text file. (12808)
[SEEK] Added OLTS application support for
MU100020A/21A/22A/23A OTDR modules.
Fixed bugs
[ETH] Fixed bug preventing display of SyncTest application start
screen depending on option combination when using
MU100010A software versions later than 9.10. This bug occurs
with the following hardware: (12687)
With MT1000A-005 installed
With MU100010A-011 installed
With MU100010A-001 not installed
[ETH][MxH] Fixed bug preventing FEC Symbol Error insertion
for SFP28 when MU100011A-023 not installed when using
MU100011A Ethernet application with eCPRI/RoE BERT.
(12701)
[OTDR] Fixed bug preventing splitter loss display at Pass/Fail
evaluation. (12736)
[OTDR] Fixed bug causing MT1000A freeze when performing
averaging measurement when Auto-measurement Mode set to
“Advanced” and OTDR Test Mode set to “Auto”. (12482)
9.13 2019-12-12 Key Added Features
[OTDR] Added Pass/Fail function for measured Loss results
based on either ISO/IEC or JIS standards. (12648)
Fixed bugs
[Framework] Updated to not include initialization time (time
required until OSC lamp lit) in elapsed time after MU100090A
built-in oscillator power-on displayed in GPS pop-up. Now
able to correctly confirm 3-hour warm-up time required to meet
Holdover specification. (12642)
[Framework] Fixed bug occasionally preventing recognition of
USB memory. (12537)
[OTDR] Improved issue causing generation of unnecessary
reflections at non-Event points (other than connectors and
Network Master Pro/Flex Release Notes
11 TAA-1ETNMX0054-47
splices) at OTDR waveform measurement. This issue occurs
with the old firmware version when setting a short distance
range for the measured fiber. (12488)
[ETH] Fixed bug preventing correct statistical results ‘Remote
Failure’ measurement. This bug occurs when setting Port Mode
to ‘Forced’. (12585)
[VIP] Fixed following G0382A bugs: (9850)
Non-detection of G0382A when G0382A connected to
Network Master.
Either operation panel freeze or occasional Network Master
reboot when disconnecting G0382A from Network Master.
9.12 2019-10-10 Key Added Features
[ETH] Added Link fault signaling (LFS) emulation function for
MU100011A module interfaces of 10GbE or faster (12438)
Fixed bugs
[ETH] Fixed following bugs related to DHCP functions
Bug displaying error message each time expired DHCP
lease renewed during measurement (12436)
Bug causing unwanted address release when using DHCP
server for authenticating validity of "server identifier" option
(12367)
Bug disabling DHCP settings after address released
(12447)
[ETH] Fixed bug enabling Remote Fault detection function for
interfaces other than 1GbE auto-negotiation (12519)
[ETH][OTN] Fixed bug enabling [+OTN] button for each
MonGen, Reflector, RFC2544, and SAT application when
MU100011A-001 or MU100011A-003 not installed in
MU100011A (12416)
[Framework] Fixed bug preventing login to WLAN networks
including backslash (¥) or double quotation mark (") in SSID.
Names after SSID registration are: (¥) becomes (¥¥), and (")
becomes (¥") (12433)
[FC] Fixed bug causing unwanted insertion of IDLE pattern
between NOS pattern at insertion of Not operational (NOS)
alarm (12440)
[FC] Fixed bug causing unwanted conversion of Alarm NOS
pattern to Remote Fault pattern at 16GFC interface (12440)
Network Master Pro/Flex Release Notes
12 TAA-1ETNMX0054-47
[FC] Fixed bug causing error in insertion pattern value at
R_RDY error insertion (12440)
[FC] Fixed bug preventing insertion of IDLE pattern between
EOF pattern and R_RDY pattern when inserting error burst
(12440)
[SEEK] Fixed bug causing Fail result without executing loop at
scenario with loop processing description (12469)
9.11 2019-09-05 Fixed bugs
[ETH][MxH] Fixed bug causing abnormally large Latency
measurement result when using MU100011A 10GbE or lower
interface Related applications are Ethernet BERT, MonGen,
RFC2544, SAT (Y.1564), and eCPRI/RoE BERT. In addition,
when the SAT (Y.1564) application Latency result is abnormal,
the measurement result is an unacceptable SAC violation.
(12454, 12472)
[ETH][MxH] Fixed bug in MT1000A Ethernet BERT, Ethernet
MonGen, and eCPRI/RoE BERT causing resolution of Latency
and Jitter measurement results to not meet product
specification (5 ns). (12470)
9.10 2019-06-18 Key Added Features
[ETH] Added function to IEEE1588v2 screen to display Clock
Class level delivered by network; in addition to Class level,
added display of QL value following existing ITU-T conversion
rule. (12257)
[ETH] Added G8275.2 to IEEE1588v2 profile. (12238)
[ETH] Added function for editing PTP message joint header
flagField and displaying decode results. Added screen for
changing master port flagField to IEEE1588v2 settings and
screen for displaying code result in the IEEE1588v2 monitor;
additionally, flagField value is correctly initiated following the
Clock Class setting. (11567, 12319)
[ETH] Increased SyncTest maximum measurement time to 3
days. Added function for auto-saving all measurement results to
CSV file for measurement times exceeding 12 hours that cannot
be saved to display memory. (12239)
[ETH] For Y.1564, increased decimal points from 0 to 4 places
for Availability threshold value and increased measurement
result decimal points from 0 to 5 places to support 5G network
Network Master Pro/Flex Release Notes
13 TAA-1ETNMX0054-47
measurements requiring 99.9999% availability. (12249)
[ETH] Added function in Statistics for switching units between
byte and bit display. (12105)
[ETH] Added function for outputting Statistics in CSV format to
simplify analysis of long-term measurement results with
external software, such as Excel. (11989)
[MxH] Added 12G (Opt-9) and 25G (Opt-10) to CPRI/OBSAI
BERT line rates. (12237)
[RemoteGUI] Added function for placing remote MT1000A into
standby mode using MX100001A software. (12235)
Fixed bugs
[ETH] At 25G and higher rates when Frame size of 63 bytes or
less selected, fixed bug causing displayed Tx Frame value to be
twice actual value. (12200)
[ETH] Fixed bug causing the display to freeze when displaying a
long-term graph measurement in SyncTest. (11176, 11314)
[ETH] Fixed bug causing inability for gateway to be correctly set
when using a DHCP server over IPv4 at v9.09 Ethernet
applications. (12248)
[ETH] Fixed bug causing inability to set correct maximum IFG
value for the Line Load setting (12175)
[ETH] Fixed bug causing ARP resolution to not work across
different VLANs. (12055)
[ETH] Fixed bug preventing the correct output of random
address ranges compared to the variable address settings field
in the stream settings. (10905, 11117)
[ETH] Changed behaviour when loading a saved file with a
source MAC address set to its own unit factory default, will now
configure the unit to the factory default source MAC address the
file is being loaded on. (11112)
[ETH] Fixed a bug, some settings (announce interval, sync
interval, and minimum delay request interval) did not properly
recover after loading file setup or result when using ITU-T
G.8275.1 or SMPTE 2059 profiles in the IEEE1588v2
settings.(12322)
[RemoteGUI] Added function for placing remote MT1000A into
standby mode using MX100001A software. (12235)
[ETH][MxH] SyncTest and Pass Through now start without the
Network Master Pro/Flex Release Notes
14 TAA-1ETNMX0054-47
requirement of selecting the two ports. (12236)
[ETH][MxH] Fixed bug causing inability to set FEC ON/OFF
when using SFP28, in Ethernet and eCPRI/RoE BERT
applications for v8.01 and later. (12258)
[Framework] Fixed bug causing inability to display option name
correctly in System Information for v9.09 MU100010A and
MU110010A. (12308)
[Framework] Fixed bug preventing file sharing with Windows10
version 1709 and later. (12186)
[OTDR] Fixed bug preventing update of subsequent power
meter measurement values when cancelling the execution of
power-meter zero offset. (12240)
9.09 2019-02-13 Key Added Features
"[ETH] Added following functions to each BER, MonGen, and
SyncTest application. (11970, 12182)
1. IGMP/MLD Join/Leave function
2. Support for SMTPE 2059 IEEE1588v2 profile"
[ETH] Added Burst Length/Gap input function in the Burst
settings of both MonGen and ChannelStat application (12094)
[ETH][MxH] Added IPv6 Gateway function for Ethernet and
MxH categories. (11238)
[MxH] Added option to eCPRI/RoE application to use 25G
eCPRI on two ports simultaneously. (11969)"
[Framework] Added function to measurement results statistical
display to automatically display k/M/G value matching
measurement value. (12066)
[Framework] Added progress bar during application startup.
(12065)
[OTDR] Added function for outputting OTDR measurement
results in JSON format. (12168)
Fixed bugs
[ETH] Fixed bug when a very low frequency of errored frames
occured, causing rounding of normal frame measurement result
to nearest whole number and non-display of decimal points
(99.9999% becomes 100.00%). (12056)
[ETH] Fixed bug preventing display of all measurement results
when Latency result is 1 ms or more. (12167)
[ETH] Fixed bug at SyncTest application causing green status
Network Master Pro/Flex Release Notes
15 TAA-1ETNMX0054-47
display even with no input signal to Ext10M, Ref1pps and
dut1pps. (11819, 9412,10860)
[ETH][OTN][SDH][CPRI][FC] Fixed bug causing save failure
when saving Event log in .csv format after measurement.
(11264)
[ETH][OTN][NoFrame] Fixed bug preventing writing of values to
page 2 and 3 of QSFP28 internal register when using J1756A
CFP2-QSFP28 Adapter with MU110012A/MU110013A. (11988)
[Remote][ETH] Fixed bug preventing capture of Rx Total good
bytes using SCPI command (IFETCH). (12115)
[Remote][ETH] Fixed bug causing save error when space
character present after file name when saving frame capture
using SCPI command. (12024)
[VIP] Fixed bug do not causing G0382A to become active when
using VIP application when G0382A entered automatic standby
status. (12173)
[ETH] Fixed bug in v9.07 and v9.08 when SFP28 configuration
file loaded, forcing IEEE1588v2 and SyncE to OFF and
preventing change to ON. (12054)
9.08 2018-11-21 Fixed bugs
[SEEK] Fixed bug causing inability to change frequency
variation setting from 0 ppm when measuring BER at
xCVRQuickCheck_02 scenario. (11995)
9.07 2018-09-19 Key Added Features
[ETH] Added function to RFC2544 application allowing multiple
setting of any frame size. (11829)
[ETH] Added ON/OFF function for [Remote Fault] display at
negotiation status of BERT/Mon/Gen application. (11861)
[MxH] Added function to CPRI/OBSAI BERT application for
generating/analyzing OBSAI frame. (11873)
[Framework] Added function to show who are using the port on
the resource monitor screen of MT1000A/MT1100A. (11886)
[Framework] Added Finnish to GUI languages. (10993)
Fixed bugs
[Framework] Fixed bug preventing backup of application
settings when MT1000A/MT1100A WLAN network connection
keeps fail for long time. (11313)
[ETH] Fixed bug in the IPv4 checksum header when sending
Network Master Pro/Flex Release Notes
16 TAA-1ETNMX0054-47
multiple streams including VLAN/IPv4 or MPLS/IPv4 using
Mon/Gen application. (11855)
[ETH] fixed bug displaying a Frame capture buffer size of 513
kB and larger which isn’t possible using v9.05/v9.06 25GbE
interface. (11950)
[MxH] Changed name of "CPRI/OBSAI P.Thru" application to
"CPRI P.Thru". (11976)
[Remote][OTDR] Fixed bug causing main unit to restart when
sending :OTDR:TRAC:LOAD:TEXT? command to capture
waveform data. (11951)
9.06 2018-07-19 Key Added Features
[ETH] Added function for synchronizing time of two MT1000A
units using 1PPS and 10MHz for Latency when MU100011A
installed. (11791)
[ETH] Improved PTP measurement results Accuracy and
Latency results Accuracy and Resolution. (10877, 11790)
[ETH] Added support for RFC6349 over IPv6. (10879)
[ETH] Added second (sec) units display to vertical axis in the
Latency/Jitter sections of the BERT and RFC2544 applications.
(10789, 10824)
[Framework] Increased maximum number of alphanumeric
characters from 32 to 64 for PSK (WPA and WPA2) WLAN
connection authentication. (11526)
[FC] Added Block Error detection and insertion functions for
10GFC and 16GFC in the BERT application. (11516)
Fixed bugs
[ETH] Fixed bug in BERT and Mon/Gen applications when
reading CFG file causing TCP protocol "Listen mode" setting to
always load as "Off". (11214)
[ETH] Fixed bug in BERT application from v9.00 when using
100G interface and inserting FEC symbol error causing
application to crash when selecting either "Burst/sec" or
"Burst/10 sec" as Insertion setting. (11344)
[ETH] Fixed bug in Mon/Gen application preventing the TCP
protocol from establishing TCP sessions on streams 9 to 16.
(11221)
[ETH] Fixed bug in Sync application preventing display of Port2
TE1 and Terr graph results even when loading saved
Network Master Pro/Flex Release Notes
17 TAA-1ETNMX0054-47
measurement-results file. (11655)
[Framework] Fixed bug in File Browser from v9.02 preventing
the file saved time from being displayed. (11042)
[Framework] Fixed bug when editing a WLAN network that has
already saved the PS Key value and is described as "[key is
configured]"", if you save this value the PSK value is
overwritten. (11267)
[OTN] Fixed bug in BERT application causing an error after
selecting; RTD measurement mode, quitting application,
restarting application, and changing measurement mode to
BERT. (11495)
[OTDR] Fixed bug in Multi-Pulse Measurement preventing
correct calculation of dB/km and Cum.Loss (dB) values. (11836)
[Eth] Fixed bug sometimes causing lower measured throughput
result than actual rate using RFC6349 Application. (10883)
9.05 2018-05-08 Key Added Features
[ETH] Added 25 GbE interface to SyncTest application. (10880)
[OTN] Added OTU2e-FC1200 mapping for MU100011A
module. (10803)
[MxH] Added eCPRI/RoE BERT application. (10878)
[Framework] Added Korean language to Transport functions.
(10837)
Fixed bugs
[ETH] Resolved issue returning an incorrect ARP Reply with
below IP and MAC configuration for MU100011A with v9.00 or
later software. (11069)
SrcMAC 00-00-00-00-00-00
SrcIP 0.0.0.0
[ETH] Resolved issue displaying incorrect latency measurement
when using 2 ports in RFC 2544, MonGen, BERT applications
in v9.02/9.03/9.04 if not changing interface settings immediately
after application start-up. (10963)
[ETH] Resolved issue causing reversed positive / negative 1
PPS TE measurement results at SyncTest application v5.00 and
later. (10907)
[ETH] Resolved issue in PacketTE measurement graph not
displayed when PTP StepMode setting is different between port
Network Master Pro/Flex Release Notes
18 TAA-1ETNMX0054-47
1 and port 2 in SyncTest application after v5.00. (10906)
[ETH] Resolved issue causing the Frame Count threshold to
Fail incorrectly within the Ethernet BER application from v7.02.
(9487)
[ETH][OTN] Resolved issue causing incorrect control of
QSFP28 optical modules with Power Class 5, 6, and 7 from
v9.00. (10903)
[ETH][OTN] Fixed bug when QSFP+/QSFP28 modules
selected causing incorrect display of all Tx powers in dBm units
instead of mA units; now either mA or dBm units displayed
according to optical module specifications. (10994)
[MxH] Resolved issue causing GUI display to not follow the
instrument change to CPRI when OBSAI setting has Delay or
APS measurement is enabled. (11080)
[SDHPDH] Resolved issue causing the unit to restart when
creating a report from an E1 measurement in the SDH/SONET
application from v3.0. (10962)
[Remote] Resolved issue preventing return of the correct status
information when using CFP, CFP2, CFP4, or QSFP28 optical
modules, when querying module status using SCPI commands.
(10893)
9.04 2018-04-04 Fixed bugs
[Framework] For MU100011A serial numbers 6261738768 to
6261801145, added function for automatically correcting default
MAC address of measurement port from "00-00-00-xx-xx-xx"
set a result of bug to "00-00-91-xx-xx-xx".
Upgrade customers using instruments affected by this problem
as soon as possible to this new version. (10966)
[Framework] Fixed bug when displaying history log (list of
previous input characters) at character input dialog causing
history log to overlay numeric input buttons and prevent ability
to press buttons. (11087)
[ETH] Fixed bug causing sending of ARP Request using
destination IP address instead of Gateway address when
executing ARP with Gateway set to ON with Ethernet
application v9.03 and later. (11209)
9.03 2018-02-22 Improvement
[Standard OTDR][FTTA][Construction] Improved the performance of
Network Master Pro/Flex Release Notes
19 TAA-1ETNMX0054-47
the connection check function when using a short patch code (3m or
less). (10980)
9.02 2017-12-06 Fixed bugs
[ETH] Fixed a bug of RFC6349 causing sometimes worse
throughput than actual DUT's performance. This bug only
happens MU100010A and MU110010A in v9.01. (10888)
9.01 2017-11-30 Key Added Features
[ETH] Added function for selecting MDI/MDI-X/Auto at
10M/100M/1000M Ethernet electrical interface. (10810)
[ETH] Added In-band Remote Function including Discovery
application to MT1100A. (10811)
[NOFRAME] Added 4LaneBER measurement function to
MU100011A. (10809)
[FTTA] Added function for loading CFG file to FTTA application.
(10762)
[Construction] Added function to Construction application to
reflect cursor position set at first wavelength at waveforms for
other wavelengths when measuring several wavelengths.
(10552)
[Framework] Added function for avoiding problem of delayed
main unit start-up resulting from saving of multiple files in
internal storage of measuring instrument. (10790)
[Remote][VIP] Added function for automatically appending .vipi
extension even when specifying output file name without
extension description when using [Save with File Name] at
MMEM:STOR remote command. (10682)
Fixed bugs
[ETH] Fixed bug causing incomplete display of measured result
decimal point values when measuring Latency of multiple ports
simultaneously at either BERT or MonGen application. (10789)
[ETH] Fixed bug causing settings change according to
dependence of Gateway On/Off setting on ARP On/Off setting.
(10791)
[ETH] Fixed bug causing inability to select IPv6 Frame setting
when selecting VLAN ID 2 at Ping application. (10737)
[ETH][OTN][SDH][FC][CPRI] Fixed bug causing output of space
separator at every three numerals when numeric data such as
bit count, etc., at report creation and output in .csv format.
Network Master Pro/Flex Release Notes
20 TAA-1ETNMX0054-47
(10728)
[NOFRAME] Fixed bug sometimes causing error generation at
20LaneBER measurement using QSFP28 module with
MU100011A module. (10797)
[OTN] Fixed bug causing incorrect 0 dBm display for tunable
wavelength SFP receive power. (10799)
[VIP] Fixed bug causing display of [Analysis Failure] dialog
instead of [Failed Test] dialog when saving failed evaluation
result data. (10773)
[Standard OTDR][Construction] Fixed bug causing Sequence
Number to become 0 when loading SOR file captured by Anritsu
OTDR (MT908x, MT9090, etc.). (10449)
[Standard OTDR][FTTA] Fixed bug causing test results to not be
reflected when displaying Test Status screen at OTDR and
FTTA applications. (10320)
[Standard OTDR][FTTA] Fixed bug sometimes causing blank
Setup screen List box when reading SOR captured by Anritsu
OTDR (MT908x, MT9090, etc.) using “Load with setup".
(10755)
[OLTS] Fixed bug causing non-display of OLTS progress bar
when Test Status screen displayed at OLTS application.
(10767)
[Remote][Standard OTDR] Fixed bug causing non-display of
VFL function key when starting client with INST:STAR:GUI after
starting OTDR application with SCPI. (10162)
[Remote][Standard OTDR] Fixed bug preventing correct
capture of dB/Km (fiber loss) when obtaining measurement
results using OTDR:TRACe:LOAD:TEXT? with measurement
conditions set to Automatic. (9409)
9.00 2017-09-19 Key Added Features
[New HW] Added CPRI RF Module MU100040B to
measurement module product line. (10764)
[ETH] Added FEC On/Off function to 25G Ethernet settings.
(10238)
[ETH][OTN] Added CFP2-QSFP28 Adaptor J1756A (10765)
[ETH][OTN][SDH][CPRI][FC] Added I2C analysis function for
SFP/SFP+/SFP28 Module. (10741)
Fixed bugs
Network Master Pro/Flex Release Notes
21 TAA-1ETNMX0054-47
[OTN][SDH] Fixed bug at APS test preventing APS
measurement for up to 2 seconds after measurement start.
(8937)
[Remote] Fixed bug causing incorrect PASS evaluation at
Summary Results at ARP failure at Y.1564 and Ping
applications under remote control.(9799)
8.02 2017-08-31 Key Added Features
[ETH][SDH] Added Line Rate Frequency deviation (Max., Min.,
Avg.) to the measurement items. (10715,10714)
[SDH] Added MS-AIS/AIS-L alarms into the Insert Alarm
function during Through Mode operation of the BERT
application. (10657)
[NOFRAME] Added No Frame application supporting the
following functions to the MU100011A Module. (10443)
- 25G BER for SFP28.
- 10G x4 lane BER for 40G QSFP+.
- 10G x20 lane BER for 100G CFP4/QSFP28.
[SEEK] Added Loop function and character divider command
for the MX100003A. (10691)
Fixed bugs
[ETH] Fixed bug preventing incorrect measurement of one-way
delay measurement results while using GPS connected to the
MU100090A and the Y.1564 application with V8.00/V.801.
(10733)
[ETH] Fixed bug preventing normal LOS Alarm information on
the Status screen when 25GbE is selected while using the
MU100011A module. (10732)
[ETH] Fixed bug preventing the selection of IPv6 within the Ping
application. (10722)
[ETH] Fixed bug preventing a FAIL test status when ARP failure
occurs in the Ping application. (9798)
[SDH][OTN] Fixed bug causing the display of incorrect Signal
Power value on the Status screen at 40G/100G line rates.
(10736)
[OTN] Fixed bug allowing the selection of LOS as an APS
measurement trigger condition when QSFP+/QSFP28 interface
is selected within the APS application. (10677)
[NOFRAME] Fixed bug preventing normal 20 Lane BER
Network Master Pro/Flex Release Notes
22 TAA-1ETNMX0054-47
measurement on the CFP2 interface while using the No Frame
application with the MU110013A module. (10676)
8.01 2017-06-29 Key Added Features
[ETH] Added function for stopping stream sending when Pause
Frame received at 100GbE/40GbE/25GbE. (9968)
[ETH][OTN][SDH][FC][CPRI] Added function to support the
Tunable SFP/SFP+. (9473)
[ETH][OTN][SDH][FC][CPRI] When the threshold value is set,
the color of the test result value is reflected in the PDF report.
(10173)
[ETH] At SyncTest application, changed so that PacketTE and
OWD graph magnified display performed within significant digit
range. (10504)
[OTDR] [FTTA] In Fiber Visualizer mode, added function for
displaying help to resolve issues when selecting Fail event icon.
[SEEK] Added following functions at scenario execution
function. (10484)
- Function for editing header information used at report output.
- Function for outputting results after scenario execution directly
to USB memory.
[VIP] Added exposure-compensation function to G0382.
(10354)
Fixed bugs
[ETH] With 100GbE FEC enabled, fixed bug causing PCS Skew
injection to be enabled when should not be enabled. (10451)
[ETH] At SyncTest application, fixed bug causing N/A display for
PacketTE measurement results. (10447)
[ETH] At Y1564 application when executing End-to-End
measurement, fixed bug causing main unit to restart when
frame received from port other than master port set at slave
port. (9622)
[ETH][OTN][SDH] At MU110013A, fixed bug causing main unit
to restart when I2C analysis function executed during
measurement. (10098)
[OTN] At QSFP28 interface, fixed bug preventing correct rate-
select setting for device. (10313)
[RemoteGUI] At MX100001A, fixed bug causing large font
display on screen. (9970)
Network Master Pro/Flex Release Notes
23 TAA-1ETNMX0054-47
[OTDR] [FTTA] [Construction] Fixed bug preventing input of
comma (,) period (.), forward slash (/), yen symbol (?), and
question mark (?) characters at header input screen. (10427)
[OTDR] [FTTA] Fixed bug causing initialization of calibration period
at software update. (10512)
8.00 2017-05-23 Key Added Features
[New HW] Added 100G Multirate Module MU100011A to
measurement module product line.
[Framework] Increased battery charge upper temperature limit
by 3°C. (9532)
[ETH] Added following functions to Sync Test Application
(10154) :
- Terr (min), Terr (max), max|Terr| measurement results
- 1PPS Mode for measuring packet base TE by the external
1PPS
- Function to reflect the UTC offset valve that the Grand Master
announces in broadcast message, when the network master
emulates PTP slave.
[CPRI] Separated CPRI and OBSAI GUIs for
easier-to-understand operation (9519)
[OTDR] Added real-time Check function to Construction
application (10244)
[SEEK] Changed response time-out default value after sending
remote command to 30 s (10374)
Fixed bugs
[ETH] Fixed bug causing main unit to restart when attempting to
display IEEE1588v2 Log when external logging enabled for
IEEE1588v2 function.(10107)
[ETH] At stream setting, fixed bug preventing obtaining of
source IPv4 address from DHCP server.(10226)
[ETH] Fixed bug sometimes causing unstable results when
measuring cables shorter than 10 m with cable test
application.(9477)
[FC] Fixed bug sometimes causing Frame loss when using
reflector application.(10214)
[VIP] Added SC/APC chip to selection list at G0382A usage screen
because not included in list.(10134)
7.05 2017-03-23 Key Added Features
Network Master Pro/Flex Release Notes
24 TAA-1ETNMX0054-47
[Framework] Added Quick Matrix to File input screen.
[Framework] Added support for saving/loading file names with
period (.) in file name. (9557)
[ETH] Added In-Band control function and Discovery
application. (9526)
[ETH] In RFC2544 application, upgraded to display a total of up
to 500 steps for measurement results, previously only displayed
up to 100 steps for each measurement. (8995)
[ETH] Added support to RFC254 application Burst test, allowing
configuration and displaying results in Burst seconds. (9385)
[ETH] Added support for Category 6/6a to Cable Test
application. (9474)
[ETH] [OTN] [SDH] [FC] [CPRI] On the SFP module information
display screen, change the wavelength display when mounting
Bi - Direction SFP to "Tx wavelength (Nominal)". (9520)
[FC] For FC, added performance test application(Perf. Test) to
run RFC2544-like benchmark tests. (9525)
[FC] For FC, added support for setting in Mbps units to Frame
Tx function. (8386)
[OTDR] Construction application, changed to output to only be
in SOR format files. (9560)
[Remote][ETH][OTN][SDH] Added transceiver control remote
commands support. (9530)
[SEEK] Added the following functions to MX100003A .(9752
- VIP application.
- Save file function by using a Variable.
- Quick Matrix function when specifying file name.
- Custom Application to Command Selection.
- Remove command allowing deleting of delete any characters
in a string.
[VIP] Added support for G0382A auto-focus VIP.
[VIP] Added following functions to VIP application.
- Auto-measurement function (auto-focus, auto-capture).
- Auto-recognition of probe connected to main frame.
(supports G0382A, and G0306A/B; G0382A only supports
auto-focus).
Fixed bugs
[Framework] Fixed bug causing MT1000A to freeze when
Network Master Pro/Flex Release Notes
25 TAA-1ETNMX0054-47
repetitive insertion/removal of G0306A/G0306B. (9850)
[ETH] Fixed bug in MonGen application causing restart when
terminating application while Threshold Summary screen
displayed. (9602)
[FC] Fixed bug in Reflector application causing Frame Loss at
Frame size of 8n + 4 (n = 8..267). (9231)
[OTN][SDH] Fixed bug in APS application causing switching
time to result in larger value, when set to a bit rate of 40 Gbps or
more and the trigger setting is pattern error. (9753)
[OTDR] Fixed bug preventing editing of user-registered macro
at Smart File Name. (9559)
[OTDR] Changed summary from Open to FAIL when far end not
detected. (9691)
[Remote][ETH] Fixed bug causing main frame to restart when
performing Through and Frameloss measurement of RFC2544
application via MX100001A. (9688)
[Remote][ETH] Fixed a bug causing the test application to stop
when using the stream copy function of Y1564, MonGen and
ChannelStat application via MX100001A, on the main unit it
caused a restart. (9797)
[Remote][ETH] Fixed bug allowing an unusable rate to be set via
SCPI control. (9601)
7.04 2017-02-20 Fixed bugs
[Framework] Fixed bug sometimes causing instrument reboot
when performing analysis using G0306A/B on VIP application.
(9627)
7.03 2017-01-05 Key Added Features
[ETH] Added support for two stacked VLAN to the Ping
application. (9472)
[Construction] Added setting for File Number Digit length
[FTTA] Added Manual measurement ability
[OLTS] Added Wave Code mode for auto measurement of
multiple wavelengths.
[OTDR][OLTS][FTTA][Construction] Added support for German
language in Optical fiber test applications.
[NoFrame] Added ability to save measurement results as
Report file to NoFrame application
[OTDR] Added support for PDF report generating for
Network Master Pro/Flex Release Notes
26 TAA-1ETNMX0054-47
Bi-Directional analysis result.
[OTDR] Added settings on Preference for Realtime
measurement.
Fixed bugs
[ETH] Fixed bug incorrectly enabling/disabling FEC switching
during 100G Ethernet measurement with MU110013A (9489)
[ETH] Fixed bug sometimes preventing correct sending of
received packet during instrument response to ARP/PING with
Ethernet Reflector (6965)
[ETH] Fixed bug, causing measurement screen to freeze
sometimes during PTP communications when PTP log function
is enabled (9424)
[ETH][OTN] Fixed bug causing lengthened time until event log
results displayed on screen (9370)
[Remote][OTN][SDH] Fixed bug sometimes causing option error
when setting RTD application Measurement Period using SCPI
command (9469)
[OTDR] Fixed bug when loading zip format waveform file at
Overlay condition causing screen top to display enabled (ON)
even when Bi-Directional setting changed automatically from
enabled to disabled. (9255)
[Remote] Fixed bug preventing SCPI commands of MDIO
control to work in applications except for NoFrame.(9493)
[Remote] Fixed bug sometimes preventing correct screen
enable/disable control when using SCPI remote control.(9481)
7.02 2016-10-28 Key Added Features
[ETH] Added Rate display for FEC counter (9401)
[ETH] Added I2C analysis function for QSFP28 module (9400)
[ETH] Changed initial graph display of 1PPS time error test from
Deviation to Phase Error (9313)
[GPS][MU100090A] Added function for displaying elapsed time
after lock to GPS (9068)
[NoFrame] Added function for setting different PRBS pattern at
each lane for 4Lane BER measurement function (9402)
[OTN] Added OTN test using QSFP28 module (9255)
[Remote][SEEK] Added command copy and paste functions for
MX100003A (9336)
[Remote][SEEK] Add support for OTDR application at scenario
Network Master Pro/Flex Release Notes
27 TAA-1ETNMX0054-47
creation using MX100003A (9454)
[SDH] Added AnyError to APS application trigger (9304)
[SDH] Added M0, M1, and Z2 byte setting and capture display
for OH Preset, and OH Capture function (9305)
Fixed bugs
[ETH] Corrected bug in Frame Capture function ≤10G causing a
packet whose timestamp data to be zero (9249)
[ETH] Corrected bug preventing reverse colors at OWD
threshold value evaluation in SyncTest application summary
screen (9323)
[ETH][OTN] Fixed bug at 40G/100G operation causing
initialization of inserted lane when changing Skew insertion lane
type (8839)
[ETH][OTN] Fixed bug in MU110012A preventing establishment
of Link when restarting application (8961)
[OTN] Fixed bug causing simultaneous SM-BIP8 insertion when
inserting AIS/OCI/LCK when operating at 40G/100G (9404)
[RemoteGUI] Fixed bug sometimes causing display of warning
message when quitting MX100001A (7222)
[Remote][ETH] Fixed bug sometimes preventing output of correct
measurement results when measuring Latency between Port1 and
Port2 using one measuring instrument under SCPI control (9389)
7.01 2016-10-11 Fixed bugs
[OTDR] Fixed an issue that prevented some MU100020A and
MU100021A OTDR modules from changing wavelength when
used in a low-temperature environment.
[OTDR] Fixed a bug that caused an error massage when
loading a configuration file(.cfg) created by MU100021A to
MU100020A or MU100022A.(9298)
[OTDR] Fixed a bug that could prevent remote control of the
OTDR modules when “Fail” was returned by connection
check.(9287)
[OTDR] Fixed a bug that received remote control commands
while running the Construction application.(9392)
[OTDR] Fixed a bug that caused an error when receiving the
OTDR:TRACe:TEXT? Command with an argument(s).(9393)
7.00 2016-09-14 Key Added Features
[New HW] Added New OTDR Module (MU100022A: 3wl.
Network Master Pro/Flex Release Notes
28 TAA-1ETNMX0054-47
1310/1550/1625nm model).
[ETH] Separated [Profile] and [Measurement Settings] tabs
included in [Stream] tab at BERT test into two separate tabs
labelled [Stream/Profile] and [Stream/Measurement Settings]
(9165)
[OTDR] Added Construction function.
[OTDR] Added Bi directional mode.
[New HW] Added CPRI RF Module.
Fixed bugs
[Framework] Supports simultaneous installation of three module
types.
[Framework] Fixed bug in GPS utility preventing monitoring of
GPS signal receive status.(9172)
[Framework] Fixed bug in File Explorer causing main frame to
restart when erasing file.(9099)
[Framework] Fixed bug preventing display by laser emitting
indicator during measurement when Standard OTDR
application started after VIP started.(9144)
[ETH] Fixed bug causing incorrect Frame Loss rate calculation
when Total Repeat Steps set to ON at RFC2544 test.(6445)
[ETH] Fixed bug in Sync Test application preventing input of
negative value as one-way Delay Threshold value.(9235)
[FC] Fixed bug causing incorrect display of Frame Loss
Seconds and Pattern Loss Seconds even when Frame Loss
Seconds set to Ignore at BERT application.(9173)
[OTDR] Fixed bug preventing execution of Standard OTDR
Mission Control Power Meter Offset Zero function. (9217)
[OTDR] Fixed bug causing main frame to restart when opening
OTDR results file with Result File Browser when no OTDR
module installed in main frame. (8836)
[OTDR] Fixed bug in OTDR application preventing display of
Fiber Visualizer screen waveform window when far end not
found. (8806)
[OTDR] Fixed bug causing VFL to light for several seconds
when application quit and then restarted while VFL in ON
status. (8968)
6.02 2016-08-15 Key Added Features
[ETH] Changed specification for PRBS Sync Alarm and PRBS
Network Master Pro/Flex Release Notes
29 TAA-1ETNMX0054-47
Pattern Error detection immediately after measurement start at
BER measurement using Ethernet BER application Cross
PRBS pattern (9130)
[OTN][SDH] Added measurement ON/OFF setting for following
items: (9062)
OTN: PLM
SDH/SONE: HP=PLM, LP-PLM, Threshold Alarm
[SDH] Added Generic-AIS detection function (8555)
Fixed bugs
[OTDR] Fixed bug in v6.00 causing display of "Include
Performance Verification data" checkmark at report generation
screen for results not actually displayed (9141)
6.01 2016-07-14 Fixed bugs
[ETH][OTN] Fixed bug preventing correct CFP Module
Transceiver setting and causing error when using V6.00
software with MU110011A CFP Interface (9116)
[FC] Fixed bug causing periodic Frame Loss when sending
FC1200 Frame signal (7877)
[OTN] Fixed bug in V5.01 and later software causing doubling of
output clock frequency when selecting any one of OTU1f/2f/2e
bit rates when using Tx Reference Clock Output with
MU110010A (9084)
[FTTA] Fixed bug causing disabled software key when moving
to TRACE tab at TTA application after starting measurement
(9138)
6.00 2016-06-23 Key Added Features
[New HW] Added MU110013A module and dedicated option
[Framework] Added autosave function for MT1100A CFP/CPF2
Interface transceiver settings (8568)
[ETH] Added following settings to Traffic Tx function
・Burst Tx Setting
・Frame Length Increment Tx
・Tx Rate Inter-Frame Gap Specification
・Tx Rate Millisecond Unit Lamp Tx Setting
・Tx Rate over 100% stream Setting
[ETH] Added Cross PRBS pattern setting to Payload patterns
for BERT Application
[ETH] Added function for automatically allocating IPv6 Tx
Network Master Pro/Flex Release Notes
30 TAA-1ETNMX0054-47
source address using RS/RA function
[OTDR] Added function for SCPI Remote command control to
OTDR application
Fixed bugs
[Framework] Fixed bug causing restart of main frame when
inputting "e" character while file load/save dialog displayed
(8873)
[Framework] Fixed bug causing license error display when
loading settings file saved by MT1000A+MU100010A
configuration at MT1000A+MU1000xxA+MU100010A
configuration and corrected notification to comment on
configuration difference (8633)
[ETH] Fixed bug causing non-stop sending at Pause Frame
receiving even when Auto Negotiation set to off for
10/100/1000M electrical interface and "Respond to Pause
Frame" set (8643)
[ETH] Fixed bug causing output of all selection items when
outputting test results to CSV or XML file using Channel
Statistics application (8523)
[ETH] Fixed bug causing inclusion of MPLS label value in
Address Filter Stream ID conditions using Mon/Gen application
(8543)
[ETH] Fixed bug causing Skew value to be displayed as
">0.000" and incorrect measurement when selecting any
Interval result at "Relative Skew" results display of Result
screen (8838)
[ETH] Fixed bug preventing correct display of result table
service details at measurement results for Y1564 (8527)
[FC] Fixed bug causing monitoring of Frame Loss seconds even
when "ignore Frame Loss seconds for BERT measurement
results" set at BERT application (8730)
[PTP] Fixed bug causing locking for only up to 4 hours in locking
state using GPS utility. (8548)
[OTDR] Fixed bug sometimes causing error in Reflectance analysis
results when Auto Mode Test set to Advanced. (8933)
5.04
5.03
2016-05-23 Key Added Features
[Framework] Added the One-Button Test.
Fixed bugs
Network Master Pro/Flex Release Notes
31 TAA-1ETNMX0054-47
[Framework] Fixed bug causing the unavailable access to USB
stick after the specific procedure on V5.01.(8826)
[Framework] Fixed bug causing main frame to restart when
USB memory stick removed while File Manager focused on
sub-folder in inserted USB memory.(8733)
[ETH] Fixed bug causing the application crashes when outputting
report of Ethernet RFC 2544 ”End to end network test” results
(8614)
5.01 2016-03-25 Key Added Features
[Framework] Added to fiberscope with 60 degrees tip (7961)
[OTDR] Expanded maximum settable pulse width for each
distance range (8044)
[OTDR] Changed dummy fiber (launch spool) display color to
clearly show the start of the fiber under test. (8045)
[ETH] Added auto MAC address resolution function when a
generating IPv6 Stream (NDP NS/NA) (7712)
[ETH] Added possibility to ignore Frame loss seconds count in
Ethernet BERT application (8057)
[ETH] In SyncTest application, added calibration parameter for
GPS antenna cable length. (8026)
[ETH] In SyncTest application, added high-resolution frequency
counter function (7945)
[OTN] Added LOS insertion function (7366)
[OTN] Added following APS trigger items (7775)
OTU3x/4: FAS-OTL, LOF-OTL, OOF-OTL, LOR-OTL, OOR-OTL,
OTU1x/2x/3x/4: OTU-AIS, OOM
[SDH] Added possibility to disable the display of Pointer
Movement measurements (7905)
Fixed bugs
[Framework] Fixed bug when disabling WLAN sometimes
causing instrument to temporarily freeze (8272)
[Framework] Fixed bug causing the NWM Flex with battery
option MU11001A from fully shutting down.(8391)
[Framework] Fixed the problem that MU100090A power On/Off
status isn’t stored properly occasionally. (8273)
[OTDR] Fixed bug that "Restore Default" operation does not
work after creating OTDR report.(8448)
[ETH] Fixed bug for 10GbE sometimes causing transmitter to
Network Master Pro/Flex Release Notes
32 TAA-1ETNMX0054-47
insert wrong IFG (7673)
[ETH] Fixed bug in IEEE1588 function sometimes causing UDP
checksum errors in transmitted PTP frames (7835)
[OTN] Fixed problem when starting applications with +OTN
option sometimes causing invalid option warning message
(7683)
[OTN][ETH] Fixed bug in Ethernet transmitter causing BER
alarm when Ethernet mapped over OTN using GFP-F.
(7519)(8075)
[OTN][ETH] Fixed bug causing BER alarms for MPLS mapped over
OTN using 46 byte frame size. (7844)
5.00 2016-02-19 Key Added Features
Added MU100090A Module
[ETH] Added IEEE1588 Time error measurement function.
(7892)
[ETH] Added ITU-T8275.1 profile for IEEE1588 functions
(7992)
[CPRI] Added APS measurement function to BERT application
(7099)
[Framework] Expanded MDIO Analysis functions for
CFP/CFP2/CFP4. (7976)
[OTN] Added mappings for packet based client signal.
(7975,7977,7978)
[OTN][SDH] Added BERT/APS/RTD switch mode to BERT
application (7980)
[OTN][SDH] Added SDH Transparent mapping for SDH over
OTN start (7981)
[Remote] Added support for VNC control via HTTP with JAVA
1.8 (6353)
[Remote] Added support for simultaneous SCPI and Remote
GUI control (7681)
[Remote][ETH] Added remote command for specifying save
destination for IEEE1588/SyncE Frame capture data (8198)
- ETH:PORT1:PTP:FCAP:DIR
[Remote][ETH] Added following remote commands for
performing IEEE1588 ARP analysis and querying analysis
results (8157)
- ETHernet:PORT<Pt>:PTP:MAC:ARP
Network Master Pro/Flex Release Notes
33 TAA-1ETNMX0054-47
- ETHernet:PORT<Pt>:PTP:MAC:ARP:RESult?
Fixed bugs
[OTDR] Upgraded Event (fault point) detection (search)
accuracy (8034)
[Framework] Fixed problem causing Chinese and Japanese
UTF-8 encoded CSV reports to display garbage characters
when opened in MS-Excel. (7750)
Japanese: UTF-8 to Shift JIS
Chinese: UTF-8 to GB2312
[Framework] Fixed bug preventing re-acquisition of IP address
when switching WLAN access point (7360)
[Framework] Simplified Password dialog and fixed problem
when initially enabling system password protection requiring
user to know old (default) password. (7551)
[Framework] Fixed bug causing sudden shutdown when starting
with remaining battery charge of ≤6% (7662)
[ETH] Fixed bug only permitting insertion of less than directed
block errors when inserting errors while testing at Frame rates
of >2000 bytes when testing at interface of10/40/100 Gbps
(7020)
[ETH] Fixed bug causing Frame loss when receiving IPv4 +
UDP header Ethernet Frame when Frame length not multiple of
8 bytes at 40/100GbE (7836)
[ETH] Fixed bug restricting the minimum payload size of
38-byte when selecting custom header at BERT application
stream setting (7725)
[ETH] Fixed bug causing [Timing: Bit rate Difference] to remain
unchanged at 0 even when clearing History at Ethernet test
(6884)
[ETH] Fixed bug causing IEEE15888 status Wall Clock Current
time affects from local MT1000A time setting (7850)
[ETH] Fixed bug causing sending of incorrect time data at
IEEE1588 communications (7715)
[ETH] Fixed bug causing display of NMX_WARNING message
when starting Ethernet application when 100GbE option
installed with MT1100A+MU110011A+MU110012A
configuration (7904)
[ETH] Fixed bug causing main frame to reboot when switching
Network Master Pro/Flex Release Notes
34 TAA-1ETNMX0054-47
BERT application custom header settings when loading settings
file saved with V2.xx when using V3.03 software (7894)
[ETH] Fixed bug causing display of NMX_WARNING message
when executing ARP on IEEE1588 function (8112)
[ETH] Fixed bug causing IP header protocol type field setting to
become UDP(0x11) or TCP(0x06) automatically after previous
setting when None set after setting Frame Format Layer 4 to
either TCP or UDP (7777)
[OTN] Fixed bug causing display of screen for making additions
when low-order ODU errors and alarms cannot be inserted at
OTN through-mode test (6950),(6643)
[Remote] Fixed bug preventing release of port resources even
when executing INST:TERM command (7369)
[Remote] Fixed bug preventing normal termination processing
of application when using multiple user control by SCPI
command (7816,7847,7029,7968)
[Remote] Fixed bugs causing MX100001A to crash at following
operations. (7933)
(1) At remote connection from MX100001A when measuring instrument
Remote PC connection set to OFF
(2) When changing measuring instrument Remote PC connection setting
from OFF to ON
(3) At remote connection from MX100001A
[Remote][ETH] Removed explanation of following unsupported
commands: (7537)
- ETHernet:CSTat:SETup:PORT<Pt>:PSELect
- ETHernet:CSTat:SETup:PORT<Pt>:PWIDth?
[Remote][OTN] Fixed bug preventing correct reading of PSI[0]
value using OH capture remote query command (7788)
[SDH/SONET] Fixed bug preventing reflection of measured
error in test results during measurement with APS application
(6982)
[Wireshark] Fixed bug causing Wireshark restart when reading
file format not supported by Wireshark (7595)
4.00 2015-12-10 Key Added Features
[NewHW] Added New OTDR Module for MT1000A
MU100020A OTDR Module 1310/1550 nm SMF
MU100021A OTDR Module 1310/1550/850/1300 nm SMF/MMF
Network Master Pro/Flex Release Notes
35 TAA-1ETNMX0054-47
Fixed bugs
[Framework] Fixed problem causing Chinese and Japanese
UTF-8 encoded CSV reports to display garbage characters
when opened in MS-Excel.
Japanese: UTF-8 to Shift JIS
Chinese: UTF-8 to GB2312
[Framework] Simplified Password dialog and fixed problem
when initially enabling system password protection requiring
user to know old (default) password.
[ETH] Fixed problem in RFC2544 application causing
instrument to restart when transmitting IPv6 formatted Learning
Frames. (7808)
[ETH] Fixed problem preventing saving of PTP message logs at
IEEE 1588v2 log. (7421)
[ETH] Fixed problem running 10G with frame sizes above 2000
bytes, sometimes preventing insertion of sufficient block errors
using error insertion function. (7020)
[OTN] Fixed problem reading PSI[0] OH byte (Payload type)
using SCPI command. (7788)
3.04 2015-11-06 Fixed bugs
[OTN] Fixed bug preventing normal detection at continuous
OLA alarm (7703)
[OTN] Fixed problem preventing PM-BIP and PM-BEI errors
being reported in Event Log. (7702)
[OTN] [ETH] Fixed problem causing Warning message while
re-loading settings file generated in an Ethernet over OTN
application. (7727)
[ETH] Fixed problem causing instrument to restart when using
Layer 2 custom header and exceeding the setup frame length
by enabling either Jitter or Latency measurement. (7674)
[ETH] Fixed problem with Latency result sometimes being incorrect
when measuring between two ports on same module. (7691)
3.03 2015-10-02 Key Added Features
[Remote] Added Remote Commands and GPIB-USB converter.
[ETH] Added Function for Custom Editing of Ethernet Header.
[ETH] Added Function for PCS at 10 GbE.
[ETH] Added Function for continues Stream address Creation.
[OTN] Added Null to Client Signals for OTN Mappings.
Network Master Pro/Flex Release Notes
36 TAA-1ETNMX0054-47
[ETH] Enhanced RFC2544 GUI for Easier Access and Better
Overview.
[ETH] Enhanced RFC2544/Y.1564 Reporting Providing More
Information.
[ETH] Renamed 'CFI' bit in VLAG tag to 'DEI' according to 2015
version of IEEE802.1Q.
[Framework] Improved Report Layout: Better Look and Distinct
Header Styles.
[Framework] Added Function for Filtering Results Display at
Report Output.
Fixed Bugs
[Framework] Fixed problem with removing USB storage while
viewing PDF or XML file stored on device (7359)
[Framework] Fixed problem with garbage characters sometimes
occurring in Japanese PDF reports created using MX100001A
Control Software and read under Windows 7 64-bit OS
environment (7028)
[ETH] Fixed problem with IEEE 1588 Log sometimes repeating
old events. (7390)
[ETH] Fixed problem with PTP clock system when running high
rates of Sync/Announce/Delay Request packets for IEEE 1588
protocol data (7389)
[ETH] Fixed problem with 40/100G Reflector application
causing statistics engine to drop frames when swapping of
IP/MAC disabled (7376)
[ETH] Fixed problem initiating OAM 802.ah Remote Loopback
on Accedian NIDs (7365)
[ETH] Fixed problem with Disruption errors sometimes reported
in Event Log while running RFC 2544 Latency Test (7361)
[ETH] Fixed problem with Pass-Through application running
GbE electrical causing dropped frames when changing clock
advertisement (master/slave) configuration (7284)
[ETH] Fixed problem with storing RFC 2544 result files when
test includes more than 148 steps (7136)
[ETH] Fixed problem with the Unicast/Multicast Tx frame
counters on "Ethernet - Transmit" statistics page not updating
when U/L bit of destination MAC address set (7108)(7103)
[ETH] When using GPS as Master Clock reference for
Network Master Pro/Flex Release Notes
37 TAA-1ETNMX0054-47
IEEE1588v2, fixed problem with current Wall Clock differing
from displayed UTC time (6996)
[ETH] For RFC 2544 and SAT (Y.1564) applications running
end-to-end network test, fixed problem with “Abort” window
remaining on slave after test finishes (6957)
[ETH] For SAT Y.1564 and Mon/Gen. applications, fixed
problem with automatically stored settings files potentially
causing applications to fail when re-launched (6956)(7529)
[ETH] Solved problem with disabling SyncE sometimes
leaving pending SSF Alarm History and Event Log entry (6912)
[ETH] Fixed problem with local port losing link when inserting
"No Link" alarm, although incoming signal OK (6877)
[ETH] Corrected table headings in RFC 2544 Latency report
when "Measure jitter by means of Latency test" enabled (7538)
[OTN] Fixed problem with not showing correct values for GMP
Justification Max/Min Cm. (7482)
[OTN] Fixed problem when using multistage mapping on OTN
where "false" LOFLOM alarms sometimes reported on
lower-order ODUs (7006)
[PDH] Fixed problem on E1 interface when Distant and No CAS
MFAS alarms sometimes also insert pattern errors (7019)
[SDH/SONET] Fixed problem with duplication of APS detailed
results when switching between ports (7382)
[Remote][NoFrame] Fixed problem setting Frequency Offset via
SCPI: NFRame:PORT<Pt>:STIMuli:TX:FOFFset <offset>
(7465)
[Remote] Fixed problem with instrument potentially
freezing/restarting when SCPI session closed immediately after
starting or terminating application server (7012) (7347)
[Remote] Fixed problem copying multiple files simultaneously to
PC from MT1000A/MT1100A using MX100001A Remote
Control Software (6986)
[Remote][CPRI] Fixed problem using
MEASurement:SETup:EVALuation:RX:INTerface?
command in CPRI BERT application (6992)"
[Remote][CPRI] When running CPRI Pass-Through application,
fixed problem preventing use of SCPI commands for setting
evaluation of measurement results (7042)
Network Master Pro/Flex Release Notes
38 TAA-1ETNMX0054-47
MEASurement:SETup:EVALuation:RX<Pt>[:ENABle]
MEASurement:SETup:EVALuation:RX<Pt>:INTerface
MEASurement:SETup:EVALuation:CPRI:PORT<Pt>:ITEM
MEASurement:SETup:EVALuation:CPRI:PORT<Pt>:ITEM:ALARm
MEASurement:SETup:EVALuation:CPRI:PORT<Pt>:ITEM:ERRor
MEASurement:SETup:EVALuation:CPRI:PORT<Pt>:TYPE
MEASurement:SETup:EVALuation:CPRI:PORT<Pt>:CNT:FAIL
MEASurement:SETup:EVALuation:CPRI:PORT<Pt>:RATio:PASS
MEASurement:SETup:EVALuation:CPRI:PORT<Pt>:RATio:FAIL
MEASurement:SETup:EVALuation:TMBPs:RX<Pt>:ITEM"
[Remote][ETH] Fixed problem with SCPI command for setting
stimuli alarm state (ETHernet:POER<Pt>:STIMuli:ALARm)
unnecessarily resetting electrical PHY, causing link loss for
several seconds (6993)
[Remote][OTN] When configured via SCPI remote control, fixed
problem with Ethernet client not obtaining link when mapped to
OTU3/4 using GFP-T (6955)
[OTN] Fixed problem using SCPI MAX and DEF parameter
values for setting Error Bits for GMP JC1/JC2 Error Items
(6775)
OTN:STIM:TX1:GMP:AEIN:EBIT MAX
OTN:STIM:TX1:GMP:AEIN:EBIT DEF
3.02 2015-07-29 Fixed Bugs
[Framework] Fixed Problem of Incorrectly Loading
Configuration File made Using MT1000A/MT1100A with
Different Options.(7110,7053,7038,7000)
[Framework] Using Remote GUI Software (MX100001A), Fixed
Problem Causing Inability to Start Editor and Viewer.(6990)
[ETH] Removed “Communication Port” for RFC 6349
End-to-End Test.(7172)
[ETH] Fixed Problem of Failing to Reflect “Expected preamble
length” Value at Loading Configuration File for Ethernet Pass
Through Application.(7156)
[ETH] Using Ethernet BERT Application, Fixed Problem of
Incorrect File Save/Read when Stream Setting for Port 2 and
Later Ports set to Unframed.(7041)
[ETH] Using Ethernet application, fixed problem causing
inability to reboot main frame when sending following query
Network Master Pro/Flex Release Notes
39 TAA-1ETNMX0054-47
commands and quitting application.(7022)
ETHernet:PORT<Pt>:OAM:DISCovery:CATalog?
[ETH] Fixed Problem of Disappearing Latency Results when
Saving and Loading Latency/Burst Result using RFC 2544
Application.(7010)
[ETH] Using Ethernet BERT Application, Fixed Problem
Causing Frame Loss when Reading V2.04 Settings File.(7004)
[ETH] After executing Ethernet Ping function, fixed problem
causing reboot when executing other Ethernet
application.(6999)
[ETH] Using Ethernet Application, Fixed Problem Causing
Screen Freeze when Sending/Receiving OAM 802.1ag/VLAN
CCM.(6980)
[ETH] Added following query parameters to SCPI
commands.(6975)
ETHernet:PORT<Pt>:IFETch?
TDL: Stream 1 Throughput Data Layer (bps). Response:
<Min>,<Max>,<Avg>
TNL: Stream 1 Throughput Network Layer (bps). Response:
<Min>,<Max>,<Avg>
TLL: Stream 1 Throughput Link Layer (bps). Response:
<Min>,<Max>,<Avg>
TPPL: Stream 1 Throughput Physical Layer without Preamble (bps).
Response: <Min>,<Max>,<Avg>
TPL: Stream 1 Throughput Physical Layer (bps). Response:
<Min>,<Max>,<Avg>
TUL: Stream 1 Throughput Utilization Layer (bps). Response:
<Min>,<Max>,<Avg>
[ETH] Using Ethernet Application, at ARP Reply Sending, Fixed
Rare Problem Causing Sending of Excess Stream Data in 1
Frame.(6970)
[ETH] Using Ethernet Application, Fixed Problem Sometimes
Blocked Correct traffic with "Include addresses in frame filter on
receiver" Settings at Rx Operation.(6964)
[OTN] Fixed Problem of Wrongly Configuring FC800 at Loading
of FC400 Configuration File for FC BERT over OTN.(7169)
[OTN] Fixed Boot Failure Problem of FC BERT over OTN
Application.(7166)
Network Master Pro/Flex Release Notes
40 TAA-1ETNMX0054-47
[OTN] Fixed problem causing no response when sending
OTN:RX<Pt>:IFET ch? S0MSIM SCPI command.(7066)
[OTN] Using OTN Application, Fixed Problem of Wrongly
Displaying MSIM Results Without Masking even at Higher-Level
Alarm.(7066)
[OTN] Using OTN application, fixed problem of incorrectly
reading Performance measurement results using SCPI
command when reading V2.02 or earlier results file.(7066)
[OTN] Fixed Problem Causing Higher-Level Summary LEDs to
Light when cHEC and tHEC Errors Detected at GFP-F/T
Mapping of OTN Application.(6972)
[OTN] Fixed Problem of Failing to Count Justification when
LOFLOM Detected using OTN Application.(6962)
[SDHPDH] Changed mistakes in SCPI command parameter
names.(7140)
T1:RX<Pt>:IFETch? (NFRame) -> (OOF)
T1:APS:RX<Pt>:EVENt NFR -> OOF
T1:STATus:RX<Pt>:ALARm? Loss Of Frame -> OOF
TMBPs:APS:RX<Pt>:EVENt NFR -> NFRame
- similar GUI value "LOF"-> "No frame"
[SDHPDH] Using SDH/PDH application, fixed problem of
inability to reboot main frame when sending following query
commands and quitting application.(7031)
E3:RX1:IFET? (PBBE)
[SDHPDH] Added E1 Balanced connector pin assignments to
manual.(6958)
[SDHPDH] Fix problem causing reboot when loading settings
file with set PDH rate at MU110011A module.(6915)
problem preventing use of threshold parameters set by
following SCPI commands at evaluation of actual measurement
results.(7042)
MEASurement:SETup:EVALuation:RX$<$Pt$>$[:ENABle]
MEASurement:SETup:EVALuation:RX$<$Pt$>$:INTerface
MEASurement:SETup:EVALuation:CPRI:PORT$<$Pt$>$:ITEM
MEASurement:SETup:EVALuation:CPRI:PORT$<$Pt$>$:ITEM:ALARm
MEASurement:SETup:EVALuation:CPRI:PORT$<$Pt$>$:ITEM:ERRor
MEASurement:SETup:EVALuation:CPRI:PORT$<$Pt$>$:TYPE
MEASurement:SETup:EVALuation:CPRI:PORT$<$Pt$>$:CNT:FAIL
Network Master Pro/Flex Release Notes
41 TAA-1ETNMX0054-47
MEASurement:SETup:EVALuation:CPRI:PORT$<$Pt$>$:RATio:PASS
MEASurement:SETup:EVALuation:CPRI:PORT$<$Pt$>$:RATio:FAIL
MEASurement:SETup:EVALuation:TMBPs:RX$<$Pt$>$:ITEM
[CPRI] Fixed Problem of Incorrect RTD Result Display at Each
Testing Interval of CPRI BERT Application.(6875)
[FC] Fixed Problem of Missing CRC Error in Errors/Alarms List
of Fibre Channel BERT Application.(6862)
3.01 2015-06-05 Key Added Features
[All] Added Error/Alarm indication summary.(6888)
[All] Added Performance Verification date in test report.(6890)
[All] Added Spanish Language support.(6891)
[Framework] Added the functionality of Storage
formatting.(6895)
[RemoteGUI] Added "Settings Editor" and "Result Viewer" on
MX100001A (Windows application).(6894, 6942)
[ETH] Added the functionality of “ Answering ARP/PING
request” and reflector MAC/IP address settings on Reflector
application. (6897)
[OTN] Added the client signal frequency result.(6887, 6868)
[OTN] Added “Pattern Bit Error Trigger” and ”LOS Trigger” on
APS application. (6867)
[ETH] Added “LOS” as a Ethernet Service Disruption test type
for optical interfaces
Fixed Bugs
[Framework] Fixed battery display information to show correctly
on MU110001A. (6902)
[RemoteGUI] Fixed the problem regarding sorting files on
windows application.(6878)
[ETH] Fixed the problem regarding SCPI command for stream
Line load. (6866)
[ETH] Fixed the problem regarding multi stream measurement
on Mon/Gen application. (6940)
[ETH] Fixed the problem regarding SDT(Service Disruption
Time) result. (6857)
[ETH] Fixed the problem regarding long term measurement on
PING application. (6834)
[ETH] Fixed the problem regarding the variable field of VLAN
Network Master Pro/Flex Release Notes
42 TAA-1ETNMX0054-47
ID. (6860)
[ETH] Fixed the problem regarding Remote Fault on Electrical
Interface.(6859)
[ETH] Fixed the problem regarding the maximum rate(CIR/EIR)
on 40/100G Y.1564 application. (6855, 4246)
[FC] Fixed the problem regarding SDT(Service Disruption Time)
result. (6863)
[FC] Fixed the problem regarding “Frame Loss Seconds” result.
(6864)
[OTN] Fixed application crash issue when starting a
measurement with threshold enabled. (6939)
[OTN] Improved regarding frequency offset.(6887)
3.00 2015-05-25 Added CPRI applications.(6465)
Added following functions to Ethernet applications:
Added RFC6349 application.(6366)
Added Layer 2 frame format support on Y.1564
application.(6398)
Added automatic service name on Y.1564 application.(6360)
Added “Include addresses in frame filter on receiver ON/OFF”
on RFC2544/Y.1564/MonGen applications.(6557)
Added following functions to OTN applications:
Added 3stage mapping on OTU3/4.(6369)
Added BMP mapping of SDH client.(6372)
Added FTFL alarm insertion/detection.(6373)
Improved the setting order of OTN Client.(6374)
Supported GFP-F Client signal up to 100G.(6369)
Added Error/Alarm statistics on APS application.(6399)
Added following functions to SDH applications:
Added Pattern Error Trigger on APS application.(6419)
Added Error/Alarm statistics on APS application.(6399)
Added following functions to FC applications:
Added Frequency offset Insertion/Monitor.(6405)
Added Reflector application.
Added following common functions:
Added GUI remote functionality from PC.(6342,6341)
Added Event Log functionality.(6400)
Added VIP application on Utility.(6367)
Added MDIO analysis functionality for CFP module.(6351)
Network Master Pro/Flex Release Notes
43 TAA-1ETNMX0054-47
Added electrical extender module support.(6483)
Added external 10MHz clock support.(6464)
Added Emphasis and Equalizer functionality for
CFP/CFP2.(6352)
Added Swedish keyboard input support.(6345)
Added CSV format report support.(6340)
Improved Utility Icon visualization.(6365,6362,6361)
Fixed Bugs [All] Fixed the problem that CFP2 interface may not
work correctly when configuring the timing source,
"Received".(6667)
[All] Fixed the problem that MT1100 which mounts MU110010A
sometimes shutdown when launching with battery.(6880)
[SCPI] Fixed the problem of Measurement Stop just after
Measurement Start.(6726)
[SCPI] Improved the stability of long term SCPI running.(6707)
[ETH] Fixed the problem that MPLS-TP result does not count up
when MPLS-TP OAM frame received.(6762)
[ETH] Fixed the problem regarding E2E communication
between MT1000/MT1100 and CMA3K on RFC2544
application.(6735)
[ETH] Fixed the problem regarding selection of throughput type
on RFC2544 application.(6658)
[ETH] Improved the stability of long term running on RFC2544
application.(6656, 6644)
[ETH] Fixed the problem that SDT result resets when LOS
detected.(6570)
[ETH] Fixed the problem regarding PCS alarm LED.(5892)
[OTN] Fixed the problem regarding the mapping for 10GbE into
ODU2e, mapping procedure is AMP (Asynchronous CBR
Mapping). (6372)
[SDH] Fixed the problem regarding Performance
measurement.(5419)
[FC] Fixed the problem regarding SDT measurement.(6531)
[FC] Fixed the problem that undersize frame sometimes
counts.(6254)
[NoFrame] Fixed the problem regarding the BERT
measurement result on NoFrame application.(6733)
Network Master Pro/Flex Release Notes
44 TAA-1ETNMX0054-47
[ETH] Default setting of throughput calculation layer is changed
on RFC 2544
[ETH] Fixed the process of handling larger test results than the
available storage on RFC 2544
[ETH] RFC 2544 “Average Throughput” test calculation fixed by
only calculating during a stable data stream
2.05 2015-03-25 Bug fixes and Improvements
[OTN] Fixed the problem regarding the error on OUT3-40GbE
mapping.(6454)
[All] Fixed the problem on MU110001A without battery
operation. (Bug only for ver. 2.04) (6411)
[All] Fixed the problem that application crashed after long term
running.(6455, 6552)
[All] Fixed the problem regarding the network configure on the
Ethernet Service Interface.(6461)
2.04 2015-01-22 Enhancements
[SCPI] Added the launching GUI command and the functionality
of switching control between the GUI and Remote.(6355)
[PDH] Added the PRBS31 test pattern on E3.(6064)
Bug fixes and Improvements
[OTN] Fixed the problem regarding through mode.(6386)
[OTN] Fixed the problem regarding the Performance
measurement. (6264)
[OTN] Fixed the problem regarding the OTN payload type
setting/detection for ODU4-ODU2e-10GE mapping. (6401)
[ETH] Fixed the problem regarding transmitting stream on
40/100G.(6281)
[ALL] Improved the stability when measuring.(6376,6229)
2.03 2014-12-18 Bug fixes and improvements
[OTN] Added some Errors (LLM-OTL, MFAS-OTL). (6262)
[OTN] Added some Error Trigger Type on APS measurement.
(6261)
[OTN] Changed the name of some Errors. (OTL, LOA, LOBL,
LOAML) (6262)
[SDH] Improved the updating results on Pointer Movement
measurement. (6265)
[ETH] Fixed the problem regarding the showing service number
Network Master Pro/Flex Release Notes
45 TAA-1ETNMX0054-47
on Y1564 application. (6295)
[ETH] Fixed the problem of End to End measurement on Y.1564
application. (6291)
[ETH] Fixed the problem that HiBER is not detected. (6230)
[FW] Fixed the problem regarding the VNC connections. (6243)
[FW] Fixed the problem regarding the Battery information on
MT1100.(6020)
[RFS] Supported ETSI R&TTE EN300 328 V1.8.1. (6263)
[RFS] Improved the stability on all applications. (6318)
[RFS] Improved the stability of the Ethernet Service Interface.
(6404)
2.02 2014-11-11 Bug fixes and improvements
[OTN] Fixed the bug which is on decode of ITU-T G709
PSI[0].(6231)
[ETH] Fixed the bug that NMX_ASSERT is sometimes
occurred. (6232)
[FC] Fixed the bugs which are interoperability issue and some
minor issues. (5088, 6253, 6254)
[Wireshark] Fixed the bugs and improved the stability.(6166)
2.01 2014-10-23 Support for the following products:
MT1100A Network Master Flex Main frame
MU110010A 10G Multirate Module
MU110011A 100G Multirate Module
MU110012A 40/100G Module CFP2
Added Fibre Channel applications
Added following functions to Ethernet applications:
Support for WAN-PHY interface
Frame capture include Wireshark
Channel Statistics
Added following functions to OTN applications:
GFP-F mapping
FC client mapping
Bug fixes and improvements
1.00 2014-06-23 Initial release. Support for the following products:
MT100A Network Master Pro Main frame
MU100010A 10G Multirate Module
Network Master Pro/Flex Release Notes
46 TAA-1ETNMX0054-47
Known Problems
Version Description
MT1000/MT1100
MU100010A
MU100011A
MU110010A
MU110011A
MU110012A
MU110013A
V10.03 [ETH] Service Disruption Time result is ±300 ms
measurement accuracy when using CFP2 interface of
Ethernet BERT application. (6858)
[ETH] [MxH] With Ethernet or eCPRI/RoE BERT
applications, screen may freeze at measurements including
UDP packets when receiving UDP packets at different
destination port than source port setting. This bug occurs
only at Port 1; if this bug occurs, restart the MT1000A as a
workaround solution. (12575)
[MxH] Pass-through delay for CPRI interface depends on
previous port mode setting. The Pass-through delay which
previous port mode is OFF is three times than the previous
port mode is NORMAL. (6876)
[SDH/SONET] Resolved issue in APS measurement
application after v7.02. On selecting Any Error as a trigger
the measurement result detected was about 10ms longer
than the actual switching time. (10849)
[ETH] Bug may cause Error frames when Line Rate higher
than 99.4% at Frame Size of 15500 bytes when performing
RFC2544 test with MT1100A 40G/100G interface. (9671)
[Remote] Bug may cause MT1000A mis-operation when
performing continued packet capture at remote operation
using MU100010A. (10942)
[ETH] Frame loss confirmed at RFC2544 test when using
v9.12, v9.13, and v10.00. (12818)
[ETH] Bug may prevent error recognition when receiving
ICMP reply packets including error with packet length of
more than 463 bytes. (12819)
[ETH][MxH] Fixed bug causing display of smaller than true
measured service loss time when [LOS] selected as
measurement type at MT1000A Ethernet BERT and
eCPRI/RoE BERT applications; bug avoided by selecting
[Ver. 9.05 or earlier] for latency/jitter timestamp. (13429)
[ETH] Fixed bug causing Ping application crash when
outputting PDF report after long-term measurement of
several days; use MX100001A Viewer report creation
Network Master Pro/Flex Release Notes
47 TAA-1ETNMX0054-47
Version Description
function (CREATE REPORT button) to create reports.
(13410)
[ETH][RoE] At 25 GbE and Frame sizes 8n+4, 8n+5, 8n+6,
and 8n+7 bytes (Example: 68, 69, 70, and 71 bytes) with
Line Rate of 80% or more, sometimes IFG of less than 5
bytes sent; DUT cannot recognize Frames when issue
occurs. (13359)