Network-Analyzer-soft Ds Nsd Tm Ae
Transcript of Network-Analyzer-soft Ds Nsd Tm Ae
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
1/32
WEBSITE: www.jdsu.com/test
COMMUNICATIONS TEST & MEASUREMENT SOLUTIONS
Key Benefits
JDSU Network Analyzer SoftwareTechnical Overview
JDSU Network Analyzer sofware lets network proessionals maintain and opti-mize voice, data, and video services quickly over next-generation networks anddecreases operational costs by enabling testing any technology, over any interace,anywhere by anyone.
Network Analyzer protocol-analysis sofware, in conjunction with the DistributedNetwork Analyzer (DNA), 10 Gigabit/Gigabit Ethernet blade hardware, and therevolutionary PacketPortal solution provides an expert network testing and trou-bleshooting solution that supports real-time measurements in LAN, WAN, and
AM environments. In addition, this solution can be deployed so that networkmonitoring and troubleshooting activities can be coordinated rom a single, cen-tralized location.
Network Analyzer sofware runs on a standalone PC or on the DNA platorm. Severaladditional elements complement the Network Analyzer solution such as ReportCenter, elephony Network Analyzer, Instrument Manager, and File ranslator.
Reduces OpEx by avoiding unnecessary dispatches andreducing mean time to repair (MTTR) from days to minutes
Greatly improves visibility at the edge when integrated withPacketPortal
Increases average revenue per user (ARPU) by eliminatingpremises visits and solving problems faster from a centrallocation
Provides aordable access on a massive scale with powerfulreal-time monitoring and analysis
Analyzes and troubleshoots across virtually any network withpervasive on-demand monitoring
Narrows QoE/QoS-aecting packet and ATM cell-basedissues to a specic location
Applications
Advance protocol analysis
Wireline solution or LAN and WAN
IPV, VoD, and VoIP QoE analysis
Advanced mobile network analysissolution or 2/2.5/3/4G technologies
Figure 1. Network
Analyzer software
provides expert
commentators for
network performance
advice and problem
resolution
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
2/32
2
Network Analyzer Software
Te JDSU Network Analyzer is one o the key sofware applications that runs on thescaleable Network Analysis and roubleshooting Solutions platorm. Tis platormprovides the oundation o advanced protocol analysis. ake advantage o extensive
diagnostic capabilities or troubleshooting and optimizing voice, video, and datanetworks, as well as 2/2.5/3/4G mobile networks.
Te DNA hardware platorm brings greater power or collecting and analyzing real-time data over multiple technologies such as Ethernet, AM, POS, Frame Relay, IPv6,MPLS, VoIP, IPV, LE, HSDPA, HSUPA, UMS, CDMA 2000, and GPRS.
Te scaleable DNA hardware platorm provides the oundation o advanced pro-tocol analysis architecture or fixed and mobile network applications. Couple thehardware with Network Analyzer and you have a powerul wireline solution orLAN and WAN networks; couple the DNA platorm with the riple Play Analyzeror IPV, VoD, and VoIP QoE analysis. Similarly, use the hardware in conjunctionwith Signaling Analyzer to create an advanced mobile network analysis solution or
2/2.5/3/4G technologies.
Distributed Network Analyzers
Network Analyzer software Triple Play Analyzer software Signaling Analyzer
software
Figure 2. Combine your DNA platform hardware with Signaling Analyzer software for mobile network
testing, with Network Analyzer software for fixed wireline network testing, and with Triple Play Ana-
lyzer software to test next-generation VoIP
Network Analysis and
Troubleshooting Solutions
Overview
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
3/32
3
Network Analyzer Software
Network Analyzer software
J6840A Network Analyzer software
J6865A Network Analyzer 10 GigE Blade Interface software
J6839A Network Analyzer Software Professional Edition
Add-on licenses
J6844A VoIP Telephony Network Analyzer
J6848A Report Center
J6825A Inverse Multiplex ing for ATM (IMA) and Multi-Link WAN Technologies license
J6835A NDIS server
J6765A Network Analyzer RFC2544 LAN benchmarking
J6766A MPLS analysis
J5425A Switch advisor
Data acquisition platform
J6801B DNA
J6802B DNA MX
J6803B DNA PRO
J6872A 10 Gigabit/Gigabit Ethernet Blade Interface
Utilities
File translator Time sync Data File Merge Utility
Network Analyzer Solution
Components
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
4/32
4
Network Analyzer Software
The J6840A Network Analyzer has extensive capabilities including:
It is the base sofware or controlling the DNA amily o products.
It runs on PCs as a sofware analyzer, using off-the-shel NDIS network interacecards (NICs) as measurement interaces or LAN (10/100/1000 Mb/s Ethernet, o-ken Ring and FDDI). For example, the 10/100 PC Cards (PCMCIA cards) ound inmost PC laptops can be used as the test interace or monitoring the LAN networktraffic, even while this card is simultaneously providing the network connection orthe PC.
It is the client sofware and GUI or accessing the J6835A Network Analyzer NDISServer running on another PC.
It provides off-line analysis, allowing previously captured and saved LAN and WANdata rom any Network Analyzer hardware platorm, JDSU Advisor or NDIS-basedNIC, to be re-analyzed using the ull eatures available on-line or captured data.
It includes file translator to allow analysis rom a variety o industry standard
ormats.Network Analyzer is pre-loaded and runs on the embedded PC in the J6802B andJ6803B platorms. It is also shipped on the DVD media with the J6801B DNA,together with a single-use license key to enable the sofware on a PC/laptop. Licensekeys plus manuals and DVD media or running the sofware on additional PCs can bepurchased as the J6840A Network Analyzer sofware product. For example, a secondengineer can control an existing DNA rom their PC, with the purchase and installa-tion o J6840A. Te engineer can also use the sofware to perorm LAN testing withan NDIS-based NIC, or perorm offline analysis o previously captured LAN or WANdata.
Network Analyzer Solution
Components
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
5/32
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
6/32
6
Network Analyzer Software
Network Analyzer offers multiple capabilities, particularly when used with theNetwork Analyzer hardware platorms. Te ollowing inormation describes theseeatures.
Flexible and unified approach lets you:
test over LAN and WAN interaces with identical network and higher-layer mea-surement eatures and user experience
analyze MPLS or troubleshooting converged networks
analyze with specialized hardware and off-the-shel NDIS PC-Card NICs
solve network problems quickly and effectively with the Expert Analyzer
anticipate network problems using perormance statistics and vitals
analyze critical ull-duplex server or backbone links
obtain thorough inormation with comprehensive network statistics
decode 500+ protocols across all seven layers test in IPv4 and IPv6 (or mixed IPv6 and IPv4) environments
navigate easily with the graphical user interace
run all the powerul measurements o the Network Analyzer, including the ExpertAnalyzer, on your own PC using Network Analyzer Sofware off-line analysis.
Guided troubleshooting lets you:
get continuous eedback on key network issues
identiy problems by severity to prioritize troubleshooting
isolate aults quickly without extensive protocol knowledge, using drill-down se-quences
stream decoded data to external storage with Run-ime Store to Media
get extensive online Help to explain problems and recommend solutions.
Network Analyzer Software
Detailed Specifications
Features
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
7/32
7
Network Analyzer Software
Information for understanding network issues lets you:
select only the required data with flexible capture and display filters
ocus on troubleshooting the network and not on configuring the instrument withthe auto-encapsulation mechanism. Tis includes support or GRE and GP tun-neling. Automatic detection with measurements are reported on the highest IPlayer.
understand traffic patterns with Connection Statistics
identiy MAC and network nodes through use o Node Discovery
export statistics to the Report Center or long-term trend analysis and more in-depth analysis
Advanced lower-layer Capabilities lets you:
monitor line vitals on all WAN/AM interaces
perorm AM analysis on a wide range o interaces up to 622 Mbps, including
the eight-port E1/1 AM analysis and inverse multiplexing, and on the sub-ratetributaries o channelized SM-4/OC-12 and SM-1/OC-3
auto-discover and perorm analysis on over 1024 AM virtual channels that havebeen reassembled (AAL-2 and AAL-5 ) in real time simultaneously on any AMinterace or tributary (cell mode analysis is also available)
perorm packet over SONE/SDH (PoS) analysis up to 622 Mbps
collect multiple statistics per DLCI on all discovered Frame Relay virtual channelsor per VPI.VCI on over a thousand AM virtual channels (in SAR mode or cellmode) simultaneously
perorm policing and graph 1-Point CDV on up to 1024 AM virtual channelssimultaneously with other measurements on all interaces except the eight-port E1/
1 multi-port LIM estimate suitable AM traffic contracts on up to 1024 AM virtual channels simul-
taneously
generate LAN traffic on 10/100/1000 Mbps and 10 GE
generate AAL-5 segmented higher layer and cell-based traffic on all AM interaces(except IMA and AM25) up to 622 Mbps
analyze over V-series and HSSI interaces
analyze HDLC, PPP and ISDN.
Network Analyzer Software
Detailed Specifications
Features (continued)
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
8/32
8
Network Analyzer Software
Advanced measurements to solve problems quickly
Network Analyzer has a wide range o specialized capabilities that will help you solve
network problems.Over the next few pages, the following capabilities are described in detail:
Expert Analyzer graphs utilization and health over time and provides summaryinormation on connections, protocols and network events o interest.
Data Filteringallows you to ocus on the important data and make efficient use othe capture buffer.
TCP Connection Analysislets you analyze CP connections and quickly identiydelay and retransmission issues.
Multi-segment jitter, latency, and packetloss identifies the source o packetdegradation across multiple segments in a network.
RTSM, run-time store to media allows post-analysis orensics on captured traffic.
Encapsulation Discoveryallows the analyzer to find the higher layer data regard-less o the lower layer encapsulation including support or tunneled GRE or GPtraffic.
Protocol Commentatorprovides a detailed list o network events on connectionsand on nodes.
Protocol Statisticsprovide a detailed view o the active protocols on the network,including utilization statistics, number o errors and average rame size.
Node Discoveryprovides a list o node physical addresses, names, network ad-dresses and events that have occurred on each node.
Baselininglets you see how the network is changing over time.
Protocol Vitalsprovide a list o every node on the network, showing utilization
and data link layer (DLL) errors. Connection Statisticsprovide a detailed view o every active connection includ-
ing the protocols used and the problems encountered.
Protocol Decodes display the contents o every packet on the network in sum-mary, detailed or hex ormat.
IPv6 Protocol Analysisis ully supported and available or all measurements andanalysis.
LMI Statistics and Commentator track statistics on the LMI channel in a FrameRelay network and identiy anomalies in protocol behavior.
ATM VPI.VCI statistics and Frame Relay DLCI statisticsprovide detailed statis-tics on a per VC and per port basis. Compliance to service level agreements is easilyseen.
ATM policingshows why data errors are occurring in AM networks.
ATM Usage Expert analyzes AM traffic to determine what would be a suitabletraffic contract or each virtual channel in terms o PCR, SCR, CDV and MBS.
Active Testsallow you to generate traffic, copy rom buffer or edit and playback,PING, and ARP.
Network Analyzer Software
Detailed Specifications
Features (continued)
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
9/32
9
Network Analyzer Software
Expert Analyzer
No matter what your traffic level is, Network Analyzer transorms data into mean-ingul diagnostic inormation, constantly monitoring the traffic on your network.Te Expert Analyzer reduces thousands o rames to a handul o significant events.It watches continuously or router misconfigurations, slow file transers, inefficientwindow sizes, connection resets, and many other problems. It does this or eachprotocol stack you have running (including IPv6); all in real time as events actuallyoccur.
Alert events indicate a serious network problem, such as zero time to live in IP.
Warning events highlight a configuration or perormance problem in the network,such as connection reused in Oracle, then list all possible reasons or the reusal.
Normal events give inormation on normal network transactions, such as OSPFrouter identified and provide statistics on the IP and MAC addresses as well as thenumber o OSPF routers identified.
An additional drill-down capability enables you to ocus on the data, discover thesource o the problem and find a recommended solution.
Figure 11. Expert Analyzer summarizes network conditions in a simple screen, with drill-down capabili-
ties for major details
Network Analyzer Software
Detailed Specifications
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
10/32
10
Network Analyzer Software
Data Filtering
Te J6801B DNA, J6802B DNA MX, J6803B DNA PRO, and J6872A 10 Gigabit/Gigabit Ethernet Blade Interace support two types o data filtering to assist introubleshooting and analyzing the large quantities o data generated on a high-speed link: capture and display filters. Hardware-based capture filters allow theuser to speciy which data the instrument should store in the capture buffer or ana-lyze in real-time. Sofware-based display filters let the user speciy which capturedrames should be shown on the display.
Te acquisition system used in the J6801B DNA, J6802B DNA MX, J6803B DNAPRO and J6872A 10 Gigabit/Gigabit Ethernet Blade Interace allows 100% o alldata via any interace to be captured (ull-duplex), regardless o the link speed,link utilization, or errors; the specialized hardware will catch everything. Ofen,the data o interest occurs rarely; even large capture buffers can fill quickly, par-ticularly rom higher rate interaces. Te data acquisition system has sophisticatedhardware capture filters so that capture memory is used with maximum efficiency,avoiding the capture o vast amounts o data o no interest. Tese capture filtersconsist o 32 simultaneous hardware protocol filters (each 256 bytes wide) andare in addition to hardware filters in the LIMs that can also filter traffic by AMVPI.VCI labels. Tese capture filters operate on all data entering the acquisitionsystem, whether or not the data is to be captured or analyzed in real-time. Onemeasurement that operates on data beore capture filtering is the Protocol Vitalsmeasurement.
Any number o hardware filters may be active at the same time; multiple activefilters are logically ORed. Network Analyzer allows you to set up filters by rameattributes. For example, when filtering LAN traffic, filters can be specified to filterrames with a bad rame check sum (FCS), runts (collisions), jabbers, dribbles, orthe data portion o the packet. When filtering by data, up to 64 bytes may be speci-fied in the data field ollowing the MAC source and destination addresses as filtercriteria or network layer or IP filters.
Figure 12. See only the data of interest with extensive filtering for voice, data and IPTV protocols
Network Analyzer Software
Detailed Specifications
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
11/32
11
Network Analyzer Software
TCP Connection Analyzer
Easily analyze CP connections and quickly troubleshoot and identiy CP connec-tion issues. With this measurement, you can examine CP flow control, messaging,response times, window sizes, retransmissions, payload statistics, and other CPcharacteristics. Tis is an off-line measurement perormed on captured data.
The statistics shown for each TCP connection are:
average acknowledgement response times
total packets sent rom a port (host)
total bytes sent rom a port (host)
average bytes per packet sent rom a port (host)
bytes per second sent rom a port (host)
good bytes per second sent rom a port (host). Tat is, the portion o the connec-tion bandwidth sent rom a port that is not associated with retransmitted packets.
retransmitted bytes per second sent rom a port (host). Tat is, the portion o theconnection bandwidth associated with retransmitted packets.
the number o retransmitted packets
the number o retransmitted bytes
graph o response time rom source and destination
graph o window size
graph o retransmissions.
Figure 13. Use the TCP connection analyzer to quickly identify TCP connection issues
Network Analyzer Software
Detailed Specifications
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
12/32
12
Network Analyzer Software
Multi-segment jitter, latency, and packet loss
Quickly identiy degradation points across a network. Use the IP multi-segmentjitter measurement to detect and report jitter, packet loss and latency across multipleNetwork Analyzer data capture files rom a distinct communication path across anetwork. Tis measurement supports IP, ICMP, CP, UDP and RP networks. Tis isan off-line measurement perormed on multiple capture files.
Measurements include:
total jitter (min, max, and average) in each direction
network jitter (min, max, and average) in each direction
source jitter (min, max, and average) in each direction
packet loss in each direction
latency (min, max, and average) in each direction.
Run-time store to media
Do you need to collect and analyze traffic over extremely long periods or have anintermittent problem that is hard to capture? Te DNA platorm lets you collect andanalyze data over long periods by utilizing unique data streaming capabilities. Inrun-time store to media (RSM) mode, the instruments streams data in run-timethrough external ports or post analysis and troubleshooting.
Te J6801B DNA, J6802B DNA MX and J6803B DNA PRO can stream to media upto 55 Mbps using the Control and Sync port. By utilizing a dedicated gigabit Ethernetport, the J6801B DNA and J6803B DNA PRO can stream up to 150 Mbps.
Figure 14. Identify IP multi-segment jitter, latency and packet loss
Network Analyzer Software
Detailed Specifications
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
13/32
13
Network Analyzer Software
Encapsulation discovery
Network Analyzer takes care o handling tunneled or encapsulated LAN traffic.
Sophisticated algorithms discover the encapsulation used on the link under test andwill configure the system or you. Simply type in the IP address or the application youwant to filter on and the sofware will take care o the encapsulation that the networkdevices are using. You can also define a filter based on the discovered encapsulation.GRE and GP tunneling is supported. All measurements and analysis are done at thehighest IP level.
Protocol commentators
At the heart o Network Analyzer is a series o commentators, which perorm real-time protocol state-ollowing analysis o rames to detect anomalous protocol events.Tese events are logged and linked to the corresponding captured rames, makingit easy or you to scroll through the capture buffer to see the events that led up to ananomalous event and then drill down into the event itsel. Commentators or many
different protocol amilies, including IPv6 and VoIP, are included.One o the most important capabilities o the protocol commentators is the abilityto detect potential problems in the network, and provide a suggestion o what to doto solve the problem, in addition to an explanation o the actual problem and tech-nology behind it. You do not have to be a network expert to detect, understand, andtroubleshoot problematic networks.
Figure 15. Commentators allow you to automatically detect problematic issues in the network and
obtain possible solutions to the problems
Network Analyzer Software
Detailed Specifications
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
14/32
14
Network Analyzer Software
Te data is displayed in a tabular or graphical ormat and can be viewed by Hub/Node, DE/DCE or LN/EQ activities depending on the link-layer technology used,to provide:
% utilization
total number o rames and bytes
rames and bytes per second
DLL (data link layer) errors
errors per second
average rame length.
Te statistics can be logged to disk and may be exported in CSV ormat or JDSUNetwork Analyzer file ormat. Tis data can then be used to generate proessional-quality reports with the J6848A Report Center sofware.
Network Analyzer Software
Detailed Specifications
Protocol statistics
o help understand variations orame length and protocol usage overtime, protocol and rame length sta-tistics are gathered simultaneouslyor the network layer and the majorprotocol stacks. Network Analyzerdisplays these statistics in both tabularand pie chart ormat, showing per-centage utilization or rame lengthdistribution by protocol. Ethernet,Frame Relay, and reassembled AMrame lengths are displayed in the ol-lowing categories:
< 64 bytes
64.127 bytes
128.255 bytes
256.511 bytes
512.1023 bytes
1024.1518 bytes
> 1 518 bytes
Figure 16. Frame Length by protocol is one of the multiple ways to view the information
Node discovery
Maintaining an up-to-date list o network nodes is key to managing many networkproblems as they occur. Network Analyzer provides an open node list that is auto-matically incremented as new discoveries are made by the node discovery algorithm.
Te node list shows MAC or bridged WAN addresses, network addresses and nodenames. Node Statistics reports use the station and server node names extensively,making node identification easier and aster. As a result, the Network Analyzer sof-ware provides useul clues to solving network problems.
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
15/32
15
Network Analyzer Software
Network Analyzer Software
Detailed Specifications
Baselining
Network Analyzer lets you collect statistical inormation over long periods andexport it to the J6848A Report Center sofware to generate management-levelreports. Armed with these reports, you can easily identiy network trends and planor uture network requirements. Te two most important measurements or this ea-ture are the Protocol Vitals and the Connection Statistics measurements.
Te Protocol Vitals measurement is one o the undamental measurements in thesystem.
It gives you a real view o the network, even i capture filters are active.
Te measurement collects a wealth o protocol-specific inormation on various pro-tocols like AM, Ethernet, Frame-Relay, IPv4, IPv6, Apple alk, IPX, OSI etc., plusline status (WAN/AM interaces).
You can select the inormation you want to graph without having to stop or restartthis or any other measurement. Tis selection makes it easy to identiy correlateddata patterns like broadcast rames versus routing packets versus Frame-Relayrame-rate, etc.
Te measurement monitors thresholds that you can easily set dynamically to detectintermittently occurring events automatically and stop the capture process or ur-ther analysis, even i the system is running unattended.
Te Protocol Vitals measurement graphs current and maximum utilization in real-time and provides current, average, peak and cumulative values in tabular ormat othe ollowing parameters:
Protocol Vitals
While the analyzer is decoding data, itis also gathering important inorma-tion rom the network. Tese networkperormance statistics can beaccessed with just a click o the mousebutton and may be viewed simulta-neously with the decoded data. TeProtocol Vitals measurement pro-vides a statistical picture o the lowerlayers and the various protocol stacksto show cumulative data and trendsover time. You can use these statistics
to identiy problems or assist in opti-mizing your network configuration.
Figure 17. Protocol Vitals allow you to examine traffic before and after applying filters
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
16/32
16
Network Analyzer Software
Network Analyzer Software
Detailed SpecificationsLAN Pre-filter utilization (%)
Post-filter utilization (%)
Pre-filter frames
Post-filter frames
Pre-filter runts
Post-filter runts (good FCS)
Pre-filter local collisions
Post-filter jabbers (good FCS)
Pre-filter late collisions
Post filter jabbers (bad FCS)
Pre-filter remote collisions
Post-filter dribbles
Pre-filter remote late collisions
Post-filter broadcast frames
Pre-filter mis-aligned frames
Post-filter multicast framesPre-filter frames (bad FCS)
WAN
(Frame Relay only)
Forward explicit congestion notification (FECN)
Backward explicit congestion notification (BECN)
Discard eligibility (DE)
ATM Physical Layer Line Status (interface dependent)
Utilization (%)
Total idle/unassigned cells
Total assigned cells received
Total frames received (AAL-2 and AAL-5)
Total cells indicating a single bit header (HEC) error
Total cells indicating detected multi-bit header (HEC) errors
Total cells indicating congestion experienced
Total cells with CLP=1 (low priority)
Total reassembled AAL-2 or AAL-5 frames with trailer CRC-32 errors
Loss of cell delineation (LCD)
Total bridged frames (LAN over ATM)
Total bridged broadcast frames (LAN over ATM)
Total bridged multicast frames (LAN over ATM)
WAN (common to Frame Relay, HDLC/SDLC, sync PPP)
Physical layer line status (interface dependent)
Utilization (%)
Total frames
Total bridged frames (LAN over WAN)
Total bridged broadcast frames (LAN over WAN)
Total bridged multicast frames (LAN over WAN)
Total octets
Throughput (kbps)Aborted frames
Short frames
FCS errors
Protocol Vitals (continued)
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
17/32
17
Network Analyzer Software
Network Analyzer Software
Detailed Specifications
Connection Statistics
Users report many network prob-lems in terms such as, I cannotconnect to a printer or the connec-tion to the network is very slow. oresolve these kinds o problems, youneed to view the activity on a partic-ular station or specific connection.
Figure 18. Obtain visibility of group of conversation by node, protocol, connection, etc.
o see who is using the bandwidth and how the bandwidth is used, Network Analyzerprovides numerous connection statistics. By simply clicking on a busy node, you willsee immediately to whom the node is talking most ofen and what protocol is used.
The display shows by column:
total rames and bytes to or rom a node
rames or bytes per second to or rom a node
utilization to or rom a node
total retransmissions to or rom a node
retransmissions per second to or rom a node
low window to or rom a node
source or destination port.
You can even differentiate between data sent or received by a device by simply usingthe Hub/Node, DE/DCE or Ln/Eq buttons. Moreover, this measurement provideseven more data than it appears at first glance. You can easily customize the view o howthe inormation is displayed by using the right-mouse-click context menu and choos-ing one o the pre-defined filters, views, or drill-down unctions. I needed, you canfilter the data shown by the protocol decode with one click or get a comprehensive listo all Alerts and Warnings generated by any node/station you select. IPv6 is ully sup-ported by Connection Statistics.
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
18/32
18
Network Analyzer Software
Network Analyzer Software
Detailed Specifications
Protocol Decodes
Many problems can be solved with the Expert Analyzer without viewing the details
o each rame. However, when needed, more than 500 protocol decodes are avail-able to help interpret the protocols as they appear on the network. A detailed displayshows the field-by-field protocol decode or every rame, while the summary displayprovides a single-line display o the key fields. A hexadecimal display provides the cor-relation with the detailed data display. For a complete list o decodes, please contactyour JDSU echnologies representative.
Network Analyzer sofware provides 7-layer decodes o all major protocols, includingSIP, IPV, MPLS, IEEE 802.1p, 802.1Q and 802.3x. Protocol decodes have a built-inprotocol ollower that will flag errors as they occur.
Figure 19. Visualize the packet data information in several ways: summary, detailed, or hex mode
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
19/32
19
Network Analyzer Software
Network Analyzer Software
Detailed Specifications
IPv6 protocol analysis
The Network Analyzer has extensive capabilities for IPv6 networks:
Expert Analyzer and Commentators or IPv6 protocol amilies, including VoIP, helpto quickly identiy root causes o problems
advanced measurements supporting IPv6 include Connection Statistics, ProtocolStatistics, and Node Discovery
extensive capture and display filters or IPv6 protocol amilies and station addresses,including IPv4 to IPv6 tunneling
VoIPv6 measurements and diagnostics, including MOS values.
LMI Statistics and Commentator
Te LMI Statistics measurement in the analyzers is used to track statistics on the LMIchannel on a Frame Relay network. Every LMI rame is analyzed and the statisticsare guaranteed to be 100% accurate. Te Commentator eature lets the user know
normal, warning and alert events, quickly and easily. ypical events are SequenceNumber Errors, N391 Errors, 392 Errors, Invalid LMI Frames, and Link Down.
Figure 20. Varieties of normal, warning, and alert events are supported in the LMI Commentator
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
20/32
20
Network Analyzer Software
Network Analyzer Software
Detailed Specifications
ATM VPI.VCI statistics and Frame
Relay DLCI statistics
When AM or Frame Relayinteraces are in use, the NetworkAnalyzer automatically collects sta-tistics on each o up to 1024 virtualchannels. Statistics are collected inreal-time beore hardware filteringtakes place. Statistics are collectedper port and per virtual channel(except where inappropriate). Tis
measurement can be run rom dataalready captured but in this case, ocourse, any hardware capture filterswill affect what statistics are gathered.
ATM Statistics (cell mode),
per VC and per port,
unless otherwise stated
Total Cells The total cells since the start of the run or last reset
Total HEC The total cells with header errors (per port only)
Total Cell Loss Priority The total cells with CLP set since the start of the run or last reset
Total Congestion The total cells with Congestion set since the start of the run or last reset
Total F5 OAM Cells The total F5 OAM cells since the start of the run or last reset
ATM Statistics (frame
mode), per VC and per
port, unless otherwise
stated
AAL indication Indicates 2 (AAL-2), 5 (AAL-5) or 0 (other/unknown) per VC
Total HEC Total cells with header errors (per port only)
Total F5 OAM Cells Total F5 OAM cells since the start of the run or last reset
Total Frames Total reassembled PDUs since the start of the run or last reset
Total CRC Errors Total AAL-5 PDUs with CRC errors since the start of the run or last reset
Total Cell Loss Priority Total AAL-5 PDUs with CLP set in at least one cell in the PDU since the
start of the run or last reset
Total Congestion Total AAL-5 PDUs with Congestion set in at least one cell in the PDU
Frame Relay statistics, per
VC and per port
Total Frames Total frames since the start of the run or last reset
Total Discard Eligible Total frames with DE set since the start of the run or last reset
Total Forward Explicit Congestion Notification Total frames with FECN set since the
start of the run or last reset
Total Backward Explicit Congestion Notification Total frames with BECN set since thestart of the run or last reset
Figure 21. ATM VPI.VCI statistics identify network per formance issues at a glance
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
21/32
21
Network Analyzer Software
Network Analyzer Software
Detailed Specifications
ATM policing
Te policing measurement operates in real-time with all AM-capable LIMs upto 622 Mbps, including IMA and AM channelized sub-rates o the J6810B SDH/SONE LIM. In all cases, policing is perormed on up to 1024 virtual circuits simul-taneously. Virtual circuits are auto discovered and the measurement is perormed inhardware prior to hardware-based AAL-2/AAL-5 reassembly, so it works in cell modeor rame mode. It can be used simultaneously in real-time with other measurementssuch as the VPI.VCI statistics and, in rame mode, with higher layer analysis. Temeasurement can also be used to post-process data rom the capture buffer or romfile (cell mode only).
The following traffic service configurations are supported:
CBR.1/DBR/UBR.1 GCRA (1/PCR0+1, CDVT0+1), no tagging
VBR.1/SBR1 GCRA (1/PCR0+1, CDVT0+1)
GCRA (1/SCR0+1, BT0), no tagging
VBR.2/SBR2 GCRA (1/PCR0+1, CDVT0+1)
GCRA (1/SCR0, BT0), no tagging
VBR.3/SBR3 GCRA (1/PCR0+1, CDVT0+1)
GCRA (1/SCR0, BT0), tagging
AM VPI.VCI provides results in a table ormat. Configuration o the traffic contractparameters can be perormed globally, in ranges o VPI.VCI or individually per VPI.VCI. Te configuration can be saved and restored rom file.
Figure 22. ATM policing verifies service level agreement contracts
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
22/32
22
Network Analyzer Software
Network Analyzer Software
Detailed Specifications
ATM Usage Expert
Te network has traffic contracts set up to protect it rom excessive traffic and thedanger o congestion. However, how close is your traffic to the contract limits? Tisuseul measurement is able to derive suitable traffic contracts or actual constant/deterministic bit rate (CBR/DBR) and variable/statistical bit rate (VBR/SBR) trafficby post-processing data rom the capture buffer. Te estimated traffic contracts canbe subsequently applied to live real-time policing analysis on the same virtual circuitin cell mode or rame mode to confirm that this is a suitable traffic contract over thelonger term.
1-Point CDV graphing
A side effect o the policing measurement is the ability to graph 1-point cell delayvariation (that is, CDV observed at a single point). Te graph is derived rom the datacollected per virtual channel o cell inter-arrival times. For each virtual channel, themeasurement keeps multiple bins o accumulated counts o inter-arrival times that
occur within the ranges covered by these bins. Te graph can be plotted as a distribu-tion o hits against inter-arrival times or hits against cells/second. As a non-intrusivepassive measurement on live traffic, this is particularly useul or observing the behav-ior o CBR/DBR traffic where CDV can impact the quality o service o the emulatedcircuit being carried in the virtual channel. Tis measurement is perormed simulta-neously with other policing measurements and a graph o any policed virtual circuitcan be displayed at any time.
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
23/32
23
Network Analyzer Software
Network Analyzer Software
Detailed Specifications
Active tests: traffic generation and packet editing
Built into the Network Analyzer sofware is a powerul traffic generator to addadvanced traffic generation and intelligent packet or capture file-editing capabilities.Ideal or installation testing and or manuacturing test and support organizations, itprovides the tools you need to thoroughly test, simulate and troubleshoot a networkdevice or problem. Network Analyzer provides intelligent packet and capture buffer fileediting or ull 7-layer customization o data to be transmitted. While you speciy ramerate, burst count, or percent utilization, the sofware automatically calculates inter-packet gaps or various traffic loads, calculates the checksum and generates a CRC.
You can quickly configure Network Analyzer to generate a single packet such as anARP or PING to troubleshoot a production network and veriy connectivity or togenerate a series o packets to saturate a test network and test new equipment and con-figurations beore network deployment.
The multitasking capabilities of Network Analyzer let you monitor the network while the
traffic is generated including: perorm active stimulus/response tests to troubleshoot a production network
test new equipment or configurations beore deploying them in the network
generate higher layer traffic over any Ethernet interace up to 10 G or any AMinterace (except IMA and AM25) up to 622 Mbps AAL-5 segmentation is per-ormed automatically. AM cell mode generation is also available.
For AM, the user is allowed to create either a set o cells, or a set o rames or transmis-sion onto a network.
For each frame or cell in a transmit set, users have the option to:
start with pre-defined templates (IP rames or cells), or
start with rames or cells previously captured on AM networks, or
create their own rames or cells.
In AM cell mode, templates are available or the creation o AAL-5 cell sequencesand F4 and F5 AM layer OAM cells. I the VPI.VCI is 0.0, templates or F1 and F3physical layer OAM cells or IMA ICP/filler cells are available.
In AM rame mode, the traffic generator rame builder allows AAL-5 rames andAM cells to be built. I cells are selected, the choice is the same as or cell mode abovebut i rame mode is selected, the rame will be encapsulated (RFC2684/RFC1483-routed) and AAL-5 segmented appropriately.
ICMP Echo (Ping)
Tis active measurement is currently available or LAN and AM. LAN Ping operatesvia any o the 10/100/1000 and 10 GE interaces and AM Ping operates via any o the
AM interaces except IMA.
Te user can speciy the source and destination IP addresses, the number o ICMPdata bytes, the time-out period, and in the case o AM, the VPI.VCI value and encap-sulation method.
Measurement logging
Measurement logging is available to store test results in a disk file. You can select log-ging or all the open measurements rom a common dialog box. Data may be logged inone o two ormats, CSV and Network Analyzer *.dat. All data are stored into files thatcan easily be opened by the J6848A Report Center sofware or the Network Analyzerapplication.
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
24/32
24
Network Analyzer Software
Network Analyzer Solution
Components
Add-on Licenses
J6844A Telephony Network Analyzer
Te elephony Network Analyzer simplifies and expedites the resolution o qual-ity and signaling problems in IP telephony networks. It provides simple and precisediagnostics o VoIP QoS through non-intrusive measurements, including the voicequality measurement known as mean opinion scores (MOS). It also provides simpli-fied troubleshooting o call signaling and control through embedded expert analysiso VoIP protocols. Te elephony Network Analyzer supports testing over LAN andWAN networks as part o the JDSU Network Analysis and roubleshooting solutions.
This powerful tool offers advanced VoIP signaling and service quality troubleshooting
capabilities including:
non-intrusive voice quality measurements using breakthrough predictive MOStechnology or passive voice clarity MOS scoring
VoIP analysis on MPLS and IPv6 networks
simple analysis that exposes the impairments to voice quality
RCP and RP voice session sorting and prioritization or easy drill-down toproblem areas
H.323, MGCP and SIP commentators with CDR completion statistics
precise measurements o IP network perormance or VoIP services
diagnostics or troubleshooting and identiying problems at the root cause.
Figure 3. Telephony Network Analyzer provides MOS and network impairments over time that affect
the quality of service
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
25/32
25
Network Analyzer Software
Network Analyzer Solution
Components
Add-on Licenses (continued)
Figure 4. Report Center: automate reports for network characterization, troubleshooting and
reporting
J6848A Report Center
Te JDSU Report Center helpsnetwork proessionals to visualize,analyze, document, and present vastarrays o network data with ease andflexibility. Report Center merges net-work data collected with the JDSUNetwork Analyzer into a commondatabase or urther analysis. Te useo this high quality, high-resolutiondata is unique to Report Center, andresults in a level o network analysispreviously unattainable with con-ventional tools.
J6825A Inverse Multiplexing for ATM (IMA) and Multi-Link WAN Technologies
Te J6825A license or the J6824A Eight-port E1/1 LIM enables sofware or InverseMultiplexing or AM (IMA), multi-link Frame Relay, multi-link PPP and multi-linkHDLC on the Network Analyzers eight-port E1/1 LIM.
Re-aggregated IMA traffic is analyzed in the same way as other AM LIMs, with cellmode and rame mode (AAL-2/AAL-5 reassembly) available, plus other AM analy-sis eatures.
J6835A Network Analyzer NDIS server
J6835A Network Analyzer NDIS server is a sofware agent process that is able toconnect to a NDIS-based NIC and capture data in promiscuous mode, perormingvarious analysis tasks. Measurements on 10/100/1000 Mbps or 10 GE, oken Ring orFDDI NICs are supported. Tis server is accessed rom the Network Analyzer sof-ware client and does not contain an analysis GUI.
J6765A RFC2544 Gigabit and 10/100 Ethernet benchmarking
Te RFC2544 Gigabit and 10/100 Ethernet benchmarking sofware license enables
active perormance benchmarking or Gigabit and 10/100 Ethernet devices and LANs.Measurements include throughput, latency, rame loss, and back-to-back rames with-out loss, all or varying rame sizes per IEF RFC2544.
Tis RFC2544 measurement enables ast and efficient benchmarking o networkdevices to certiy and troubleshoot network installations. esting is enabled using theJ6830A 10/100 BaseX, J6831A 10/100 Base FX, and J6832A Gigabit Ethernet LIMs.
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
26/32
26
Network Analyzer Software
Network Analyzer Solution
Components
Add-on Licenses (continued)
Te J6766A MPLS Analysis sofware keeps track o the different class priorities in anMPLS network specified by the experimental and QoS bits. In addition, the measure-ment analyzes the MPLS payload and detects the DiffServ priorities o the IP packettransported by an MPLS rame.
Key MPLS measurements include:
MPLS CoS analysis
DiffServ analysis
routing and MPLS decodes
MPLS protocol filtering
LSP statistics
VoIP perormance on VPNs.
Figure 5. Easy to view traffic levels by MPLS Class of Service and IP DSCP
J5425A Switch Advisor
Te Switch Advisor provides the capability to trend switch port utilization andother vital statistics. It allows the user to monitor a suspect WAN link and anyother management inormation base (MIB) supported device simultaneously
to correlate problems between the two. Te user can discover switches and otherMIB-supported devices via user-directed search or can directly enter the devicemanagement IP address and graphically view current port utilization levels. TeSwitch Advisor sends SNMP messages over an Ethernet connection and gathersMIB data including utilization, packet inormation, and errors.
J6766A MPLS analysis
Network Analyzer captures anddecodes MPLS signaling and data pro-tocols in real-time and at ull-line rate.Te analyzer can diagnose and decodeMPLS accordingly with RFC2547bisamong other MPLS standards.
Network Analyzer can filter single orup to six MPLS stack labels. NetworkAnalyzer creates a table o LabelSwitched Paths (LSPs) present in thenetwork and measures the vital sta-tistics o the VPN in real time. It alsoquickly creates a graphical visualiza-tion. VoIP over MPLS perormance isanalyzed on the filtered traffic to indi-cate perormance and trouble spots ora specific label-switch path or VPN.
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
27/32
27
Network Analyzer Software
Network Analyzer Solution
Components
Data Acquisition Platforms
PacketPortal
PacketPortal is a distributed packet acquisition and selective packet orwarding
system that can capture traffic rom points in a network and orward it to a PA andother Ethernet-based applications or analysis. Enhanced SFP optical transceiverscalled SFProbes give PacketPortal enhanced network visibility normally reservedor taps or span ports which are directly connected to monitored devices.
PacketPortal lets you collect data throughout the entire network, rom the edge tothe core, by leveraging existing SFP ports and network cabling to inspect, filter, andorward traffic. PacketPortal reduces the need or separate network monitoring inra-structure by taking advantage o the network capacity already in place. PacketPortalprovides access to network, service, and application data in near realtime.
The PacketPortal system consists of the following major components:
SFProbe installed in network switch and router ports in place o normal SFPs.SFProbes capture traffic based on filters and orward it across the network to PREs.
Packet routing engine (PRE) aggregates captured traffic rom SFProbes anddistributes it to analysis applications.
System manager (SM) provides a graphical user interace or command andcontrol o SFProbes and PREs.
The JDSU SFProbe PacketPortal-enabled logo
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
28/32
28
Network Analyzer Software
Network Analyzer Solution
Components
Data Acquisition Platform(continued)
For detailed inormation on the DNA Hardware Platorm, please consult the JDSUDistributed Network Analyzer Data Sheet (P/N 5988-4176EN).
J6801B DNA
Te J6801B DNA achieves its small orm actor by excluding an integrated PC. Youcan control a DNA locally or remotely rom a separate PC. One or more DNAs canbe added to create multi-port systems. Like the DNA MX and DNA PRO, the DNAincludes an acquisition system and accommodates line interace modules. Under thisconfiguration, the J6840A Network Analyzer runs on a PC and connects to a DNA toacquire data rom the network under test.
Figure 6.
Figure 7.
J6802B DNA MX
Te J6802B Distributed Network Analyzer MX is a transportable and rackmountableprotocol acquisition and analysis solution. When deployed into the network undertest, use DNA MXs to perorm distributed measurements at different points in your
network. An embedded version o the J6840A Network Analyzer runs in the inte-grated PC o the J6802B. In addition, remote Network Analyzer sofware can accessand control the DNA MX via Instrument Manager.
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
29/32
29
Network Analyzer Software
Network Analyzer Solution
Components
Data Acquisition Platform(continued)
Figure 8.
Figure 9.
J6803B DNA PRO
Te J6803B DNA PRO offers the most advanced eature set in the DNA portolio. Youcan control the analyzer rom a PC, locally or remotely. Te analyzer hosts the J6840ANetwork Analyzer or ull protocol analysis and network testing. It supports Run-ime Store to Media (RSM) up to 150 Mbps. Like the DNA MX, Network Analyzeris accessed using a remote session. Te hardware includes a built-in controller and aremovable hard disk drive. Te use model o the DNA PRO is as a portable analyzeror local or remote troubleshooting.
J6872A 10 Gigabit/Gigabit Ethernet Blade InterfaceTe J6872A 10 Gigabit/Gigabit Ethernet Blade Interace provides advanced packetcapture and processing or high speed Ethernet networks. Tis ull-length, ull-heightPCI Expressinterace card provides ull 10 G capture, extensive filtering, and net-work key perormance indicators to solve more network problems quickly. Install it ina PC or Server or ull 10 GE per second Ethernet analysis.
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
30/32
30
Network Analyzer Software
Network Analyzer Solution
Components
Access and Managementof DNAs
Secure Web browser control
Te DNA PRO and DNA MX can be controlled using a Windowsweb browser roma standard PC. Tere is no need to have any Network Analyzer sofware installed onthe client PC. Additionally, i the wireless option or the DNA PRO is present, thisplatorm can be controlled rom a WiFi-capable laptop, notebook or PDA (personaldigital assistant).
Network Analyzer Instrument Manager
Network Analyzer Instrument Manager is a sofware application that is used to con-trol several remote J6803A DNA PRO or J6802B DNA MX platorms, with or withoutattached J6801B DNAs. Tese DNAs are seen as extra interaces on the DNA PRO orDNA MX platorms.
Instrument Manager lets you:
discover all DNA PRO or DNA MX on a local subnet and discover any attachedDNAs
add a DNA PRO or DNA MX rom discovered list (instruments beyond the localsubnet must be added by IP address)
allow a remote session to the desktop using remote desktop protocol (RDP)
update sofware on multiple DNA PROs and/or DNA MXs simultaneously
display instrument status up (reachable)/down (not reachable)/locked (to a user)
configure DNA PROs and DNA MXs (assigning hostnames, changing OS pass-words, etc.)
configure DNAs
get DNA status inormation such as LIM type and whether the DNA is in use.
Figure 10. Access and manage your DNAs remotely using Instrument Manager
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
31/32
-
8/12/2019 Network-Analyzer-soft Ds Nsd Tm Ae
32/32
Network Analyzer Software