Pasolink+ XPIC Training Course.GENERAL DESCRIPTIONCHAPTER 01

GENERAL DESCRIPTION

INTRODUCTIONNEC's Pasolink+ XPIC can operates in frequency bands from (6 38) GHZ.

NECs Pasolink+ XPIC supports the following transmission capacity:-

SDH 2 x STM-1 optical / electrical interfaces.

Optional 2 10/100 Base-T(X) LAN signal.

NECs Pasolink+ XPIC uses 128 QAM + RS modulation technique.

The following table shows a summary comparison for Pasolink family.

GENERAL DESCRIPTION

PASOLINK FAMILY

GENERAL DESCRIPTION

EQUIPEMENT FEATURES (1/8)ADVANCED TECHNOLOGIES AND SUPERB PERFORMANCE MMIC, HIC AND VLSI Single chip modulator/ demodulator (Full digital) Square-root Nyquist Roll-off shaping filter High reliability Low power consumptionHIGH TRANSMISSION CAPACITY2 x 155 MB transmission capacity is realized by XPIC (Cross Polarization Interference Canceller) technology. MITIGATION OF INTERFERENCEPossible interference caused by co-channel transmission is mitigated with orthogonal polarized input channel and the XPIC (Cross Polarization Interference Canceller) device. HIGH SYSTEM GAIN High system gain achieved by using 128 QAM + RS modulation techniques.

GENERAL DESCRIPTION

EQUIPEMENT FEATURES (2/8)EASY AND QUICK INSTALLATION Very compact and light Only one coaxial cable interconnection Different mounting methods for IDU, ODU and Antenna Easy antenna pointing adjustments (RX level monitor point in ODU)SYSTEM FLEXIBILITY Hot Standby/ Space Diversity / Twin Path systems are available with Hitless switch. Common IDU for different RF frequencies (6/7/8/11/13/15/18/23/26//38 GHz) (1 + 0 ) unprotected or ( 1+ 1) protected.FREQUENCY AGILITY AND EASY TUNINGField tunable local-oscillator (Synthesizer).RF point frequency can be changed in the field, (except 6 8 GHz).Frequency Tunable without changing RF FIL on Sub-band basis (except 6 8 GHz).

GENERAL DESCRIPTION

EQUIPEMENT FEATURES (3/8)TX POWER CONTROL Variable : 0 to 20 dB , 1 dB step variable. Automatic Transmit Power Control (ATPC) or Manual Transmit Power Control (MTPC)EASY MAINTENANCE FACILITIES Full front panel access for all cabling and user interfaces Near End and Far End Base-band Loop back facilities Remote monitoring of ODU operating condition from IDU OW calling facility between IDU - ODU, IDU IDU and ODU-ODU Local monitor and maintenance using Local Craft Terminal (LCT) Continuous RSL monitoring using Local Craft Terminal (LCT) Pre-settable BER alarm point. IF Loop back facility.

GENERAL DESCRIPTION

EQUIPEMENT FEATURES (4/8)MULTIPLE SERVICE CHANNELS Engineering Order Wire (OW) : IDU- IDU (Standard) IDU - ODU (In case using PASOLINK MONITOR (Option)) ODU-ODU (In case using PASOLINK MONITOR (Option))Service channels : - Digital Port : 64 kbps Sync., 2 ch standard. VF Port : 0.3 to 3.4 kHz (1 ch) 600 ohms, 2 ch standard. 10 Base-T : 1 ch (optional; exclusive use in other service channels). Cluster Alarm : 2 ch (optional; auxiliary alarm transmission). The system configuration is easily updated :-1 x STM-1 (1+0) to 2 x STM-1 (1+0).1 x STM-1 (1+0) to 2 x STM-1 (1+1 with hot standby).1 x STM-1 (1+0) to 2 x STM-1 (1+1 with twin path). COMMON PLATFORM ARCHITECURE.

GENERAL DESCRIPTION

EQUIPEMENT FEATURES (5/8) Complies with ETS 300385ELECTRO MAGNETIC COMPATIBILITY (EMC)CONFORMITY WITH ANSI, ITU-R, ITU-T AND ETSI STANDARDSNEC Quality control is carefully monitored in every manufacturing step, such as parts selection, assembly, adjustment and testing.

NEC Quality Controls employing Zero Defect and Value Engineering Techniques extend to every aspect of production and inspection in accordance with stringent Total Quality Control programs.RELIABILITY AND QUALITY User friendly operation as maintenance terminal.PASOLINK NETWORK MANAGEMENT TERMINAL (PNMT) (OPTION) Link oriented monitor and control. Uses Windows 2000/XP which enable use of mobile PC

GENERAL DESCRIPTION

EQUIPEMENT FEATURES (6/8)PASOLINK NETWORK MANAGEMENT SYSTEM (PNMS) (OPTION) User friendly operation Uses Windows 2000/XP to ensure easy operation and maintainability Remote access and control of any PASOLINK Terminal in the network Link oriented monitor and control ( both side of a microwave link) Multi level security Event Logging ITU-T G.826 Performance Monitor (Table /graph presentation) Real-time monitor of Network Elements (NE) SNMP Interface (Option)

GENERAL DESCRIPTION

EQUIPEMENT FEATURES (7/8)Flexible ODU Mounting Configurations.Suitable configuration can be selected from various ODU mounting styles.

Direct Mounting on Antenna.

Remote Mounting with Waveguide or Coaxial Cable.11-38 GHz Remote Mount Dual Pole System6-8 GHz Remote Mount Dual Pole System

GENERAL DESCRIPTION

EQUIPEMENT FEATURES (8/8)Flexible ODU Mounting Configurations (Cont.)11-38 GHz Direct Mount Dual Pole System

GENERAL DESCRIPTION

Compatibility

GENERAL DESCRIPTION

System CompositionsThe system consists of the following :-

MDP-150MB7T-( )A Modulator-Demodulator (Indoor Unit (IDU)).

TRP-( )G-1AA Transmitter-Receiver (Outdoor Unit (ODU)).

Orthogonal Mode Transducer (OMT) (for antenna direct mounting).

Hybrid for 1+1 one antenna configurations.

Antenna for required MW band.

IF Cable.

RF Cables for ODU Remote mounting.

GENERAL DESCRIPTION

IDU Composition for 1+0

GENERAL DESCRIPTION

IDU Composition for 1+1

GENERAL DESCRIPTION

IDU Performance Characteristics (1/3)

GENERAL DESCRIPTION

IDU Performance Characteristics (2/3)

GENERAL DESCRIPTION

IDU Performance Characteristics (Cont.) (3/3)

GENERAL DESCRIPTION

ODU Indication Label

GENERAL DESCRIPTION

ODU Composition for (6/7/8 GHz)

GENERAL DESCRIPTION

ODU Composition for (11/13/15 GHz)

GENERAL DESCRIPTION

ODU Composition for (18/23/26/38 GHz)

GENERAL DESCRIPTION

ODU Performance Characteristics.

GENERAL DESCRIPTION

OMT (Ortho Mode Transducer). (1/3)OMT TransducerNEC has developed the Ortho-Mode Transducer (OMT) over the full range of microwave frequencies for Wave Guide interface of PASOLINK Series digital microwave radio point-to point fixed wireless systems. The OMT comprises the Ortho-Mode transducer, antenna interface and radio mounting interfaces.

The two independent RF signals received by dual polarized antenna are separated and sent to two outdoor units (ODUs) through the OMT for 2+0 systems.

The OMT enables the dual polarization feature to double the transmission capacity for the PASOLINK system.

The NEC OMT has a Wave Guide connection type for 13-38GHz Bands, which is suited for RFS Antenna and all NEC ODUs.Features

Direct mount integration with smart design for PASOLINK Series

Easy Installation

High XPD (cross polar discrimination ratio)

GENERAL DESCRIPTION

OMT (Ortho-Mode Transducer) (Cont.) (2/3)OMT Physical Dimensions

GENERAL DESCRIPTION

OMT (Ortho-Mode Transducer) (Cont.) (3/3)OMT Specifications

GENERAL DESCRIPTION

Hybrid Combiner / Divider. (1/4)6/7/8 GHz Hybrid13 38 GHz HybridNEC has developed the Hybrid Combiner/Divider over the full range of microwave frequencies for the PASOLINK Series digital microwave radio point-to-point fixed wireless systems.

This Hybrid Combiner/Divider comprises a directional coupler, antenna interface, radio mounting interfaces and polarizer.

The RF signal power received by the single polarized antenna is equally distributed and sent to two outdoor units through the Hybrid Combiner/Divider for 1+1 protected systems.

There are two types of NEC Hybrid Combiner/Divider, one is a coaxial cable connection type for 6/7/8GHz Bands and the other is WG connection type for 13-38GHz Bands.

NEC Hybrid Combiner/Divider is suited for Andrew, RFS, or PAL Antenna, and all NEC ODUs.

GENERAL DESCRIPTION

Hybrid Combiner / Divider. (Cont.) (2/4)7/8 GHz Hybrid Physical Dimensions

GENERAL DESCRIPTION

Hybrid Combiner / Divider. (Cont.) (3/4)13 - 38 GHz Hybrid Physical Dimensions

GENERAL DESCRIPTION

Hybrid Combiner / Divider. (Cont.) (4/4)13 - 38 GHz Hybrid Specifications

GENERAL DESCRIPTION

Pasolink Antenna menu and performance for direct mount types. Note 1: 18-38GHz antennas are provided with standard waveguide flange (PBR) and PASOLINK original interface.(13-15GHz antennas are provided with PASOLINK original interface and without standard waveguide flange.)

Note 2: In case of 7,8,13 and 15GHz remote mount configuration, please dont use this table.(Please refer to the standard catalog of the antenna supplier).

Note 3: This table shows typical values for reference.

Note 4: In case of Dual Pole Direct Mount Antenna System, * marked Diameters are available.

GENERAL DESCRIPTION

General Performance Characteristics. (1/2)

GENERAL DESCRIPTION

General Performance Characteristics (Cont.) (2/2)

GENERAL DESCRIPTION

GENERAL DESCRIPTIONPersonal link paso linkMLCMGENERAL DESCRIPTION