nd STEVAL-IPM07F nd - STMicroelectronics · IPM STGIF7CH60TS-L 700 W motor control power board...
Transcript of nd STEVAL-IPM07F nd - STMicroelectronics · IPM STGIF7CH60TS-L 700 W motor control power board...
-
Features• Input voltage: 125 - 400 VDC• Nominal power: up to 700 W• Nominal current: up to 4.2 A• Input auxiliary voltage: up to 20 V DC• Single or three-shunt resistors for current sensing (with sensing network)• Two options for current sensing: dedicated op-amps or through MCU• Overcurrent hardware protection• IPM temperature monitoring and protection• Hall sensor or encoder input• Uses the STGIF7CH60TS-L IGBT intelligent power module from the SLLIMM™
2nd series IPMs• Motor control connector (32-pin) interfacing with ST MCU boards• Universal conception for further evaluation with bread board and testing pins• Very compact size
DescriptionThe STEVAL-IPM07F is a compact motor drive power board based on the small low-loss intelligent molded module SLLIMM™ 2nd series product (STGIF7CH60TS-L) . Itprovides an affordable and easy-to-use solution for driving high power motors for awide range of applications such as power white goods, air conditioning, compressors,power fans, high-end power tools and 3-phase inverters for motor drives in general.The IPM itself consists of short-circuit rugged IGBTs and a wide range of features likeundervoltage lockout, smart shutdown, internal temperature sensor and NTC, andovercurrent protection. The main characteristics of this evaluation board are smallsize, minimal BOM and high efficiency. It includes an interface circuit (BUS and Vccconnectors), bootstrap capacitors, snubber capacitor, hardware short-circuitprotection, fault event signaling and temperature monitoring. In order to increase theflexibility, it is designed to work in single- or three-shunt configurations and with twocurrent sensing options: either three dedicated onboard op-amps or with op-ampsembedded on the MCU. The Hall/Encoder part completes the circuit. Thanks to theseadvanced characteristics, the system is able to achieve fast and accurate currentfeedback conditioning, meeting most of the requirements for field oriented control(FOC). The STEVAL-IPM07F is compatible with ST’s STM32-based control board, fora complete motor control platform.
Product summary
STEVAL-IPM07Fcompact motor drivepower board
STEVAL-IPM07F
STGIF7CH60TS-LSLLIMM™ 2nd seriesIPM
STGIF7CH60TS-L
700 W motor control power board based on STGIF7CH60TS-L SLLIMM™ 2nd series IPM
STEVAL-IPM07F
Data brief
DB2745 - Rev 4 - September 2019For further information contact your local STMicroelectronics sales office.
www.st.com
http://www.st.com/en/product/steval-ipm07f.htmlhttp://www.st.com/en/product/stgif7ch60ts-l.htmlhttps://www.st.com/en/product/steval-ipm07fhttps://www.st.com/en/product/STGIF7CH60TS-Lhttp://www.st.com
-
1 Schematic diagram
Figure 1. STEVAL-IPM07F circuit schematic (1 of 6)
STEVAL-IPMnmx decoder
N
M
X
RC6
0
RC2
0
RC1
0
RC10
0
RC7
0
RC3
0
RC8
0
RC4
0
RC5
0
RC9
0
STEVAL-IPM07FSchematic diagram
DB2745 - Rev 4 page 2/9
-
Figure 2. STEVAL-IPM07F circuit schematic (2 of 6)
Current_A
Current_B
Current_C
phase_Aphase_Bphase_C
3.3V+5V
EM_STOPPWM-A-HPWM-A-LPWM-B-HPWM-B-LPWM-C-HPWM-C-L
NTC_bypass_relay
PWM_VrefM_phase_A
M_phase_B
Bus_voltage
M_phase_C
TSO
NTC
Current_B_amp
E2
Current_C_amp
E3
Current_A_amp
E1
J3
Motor Output
123
SW2
1
2
3
SW4
1
2
3
SW3
1
2
3
J2
Control Connector
1 23 45 67 89 10
11 1213 1415 161719212325 2627 2829 3031 3233 34
18202224
SW1
1
2
3
STEVAL-IPM07FSchematic diagram
DB2745 - Rev 4 page 3/9
-
Figure 3. STEVAL-IPM07F circuit schematic (3 of 6)
InputDC_bus_voltage
3.3V
+Bus
3.3V
1.65V
Bus_voltage
D1BAT48JFILM
+ C447µ/35V
J1
INPUT-dc
12 R2470K
R3 120R
R1470K
R61k0
-
+
U1D
TSV994
12
1314
411
+ C347µ/35V
R47k5
C210n
+C1
R51k0
STEVAL-IPM07FSchematic diagram
DB2745 - Rev 4 page 4/9
-
Figure 4. STEVAL-IPM07F circuit schematic (4 of 6)
3.3V
1.65
V
1.65
V
3.3V
1.65
V
3.3V
E1
Cur
rent
_A_a
mp
E2
Cur
rent
_B_a
mp
E3
Cur
rent
_C_a
mp
R30
1k0
R29
2k1
-+
U1A
TSV9
94
3 21
4 11
TP24
R31
1k
R43
2k1
C30
100p
R37
1k0
C29
330p
R41
1k
C24
100p
C28
10n
C25
330p
TP25
-+
U1B
5 67
4 11
R35
1k0
C23
100n
C22
10n
R34
2k1
R33
2k1
R42
1k0
C31
330pTP
26
R32
1k0
R39
2k1
+
C21
4.7u
50V
C27
100p
-+
U1C
10 98
4 11
R40
1k0
R38
2k1
C26
10n
R36
1k
TSV9
94
TSV9
94
STEVAL-IPM07FSchematic diagram
DB2745 - Rev 4 page 5/9
-
Figure 5. STEVAL-IPM07F circuit schematic (5 of 6)
Phas
e A
- inp
ut
Phas
e B
- inp
ut
Phas
e C
- in
put
IPM
mod
ule
1_SH
UNT
1_SH
UNT
3_SHUNT
3_SHUNT
3.3V
+Bus
phas
e_A
phas
e_B
phas
e_C
3.3V
3.3V
SD
TSO
NTC
PWM
-A-L
PWM
-A-H
PWM
-B-L
PWM
-B-H
PWM
-C-L
PWM
-C-H
EM_S
TOP
E3 E2 E1
TP16
SW6
U2
STG
IF7C
H60
TS-L
NW
18
VBO
OTw
4VB
OO
Tv3
LIN
v11
GN
Da
9
LIN
u10
LIN
w12
GN
Db
16
VCC
L13
SD14
CIN
15
NC
1
VBO
OTu
2
HIN
u5
HIN
v6
HIN
w7
VCC
H8
NV
19
NU
20
W21
V22
U23
P24
T225
T126
TSO
17
TP2
R10
12k
R27
0.08
R11
3k3
R53
4.7k
R8
1k0
R22
3k3
R16
3k3
SW5
C8
100n
TP6
C14
10p
TP18
R7
3k9
R24
1k0
TP13
R18
1k0
R23
1k0
TP8
R17
3k9
R13
3k9
C20
330p
C15
10p
TP20
TP5
D2
LED
Red
R19
1k0
R28
10k
C19
1n
C17
10p
R9
1k0
R20
1k0
TP22
D3
BAT4
8JFI
LM
TP23
R15
1k0
C11
10p
C18
10p
C6
2.2u
+C
124.
7u 5
0V
SW7
TP7
R25
0.08
C9
0,1
uF -
400V
D6
BAT4
8JFI
LMTP3
TP1
TP14
TP19
TP21
C13
100n
D5
BAT4
8JFI
LM
R12
5k6
C10
10p
C5 2.2u
SW8
TP4
TP17
TP10
R21
1k0
R26
0.08
J415V 12
TP15
D4
BAT4
8JFI
LM
TP12
C16
1nF
R14
1k0
C7 2.2u
TP11
TP9
STEVAL-IPM07FSchematic diagram
DB2745 - Rev 4 page 6/9
-
Figure 6. STEVAL-IPM07F circuit schematic (6 of 6)
H3/Z
+H2
/B+
H1/A
+
GND
+ 3.
3/5V
Hal
l/Enc
oder
M_p
hase
_A
M_p
hase
_C
M_p
hase
_B
3.3V +5
V
3.3V
+5V
R52
4k7
R49
2k4
J5
Enco
der/H
all
11
22
33
44
55
SW12
SW13
C37
10p
C34
100n
SW10
R50
4k7
SW14
SW9
1
2
3
R44
4k7
R51
4k7
R45
4k7
C33
100n
C35
10p
R47
2k4
R48
2k4
C32
100n
SW16
1
2
3
SW15
R46
4k7
SW11
C36
10p
STEVAL-IPM07FSchematic diagram
DB2745 - Rev 4 page 7/9
-
Revision history
Table 1. Document revision history
Date Version Changes
12-Nov-2015 1 Initial release.
16-Mar-2016 2 Updated figure 1 and figure 3.
04-Apr-2018 3 Updated: title, features and figure 5.
16-Sep-2019 4
Updates Figure 3. STEVAL-IPM07Fcircuit schematic (3 of 6) andFigure 4. STEVAL-IPM07F circuitschematic (4 of 6).
STEVAL-IPM07F
DB2745 - Rev 4 page 8/9
-
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to STproducts and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. STproducts are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design ofPurchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks. All other product or servicenames are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2019 STMicroelectronics – All rights reserved
STEVAL-IPM07F
DB2745 - Rev 4 page 9/9
http://www.st.com/trademarks
1 Schematic diagramRevision history