NCSX Modular Coil Turning Fixture FDR

27
NCSX Modular Coil Turning Fixture FDR

description

NCSX Modular Coil Turning Fixture FDR. FDR Charge (answers were added below after the review). Modular Coil Turning Fixture FDR - Charge to Reviewers - PowerPoint PPT Presentation

Transcript of NCSX Modular Coil Turning Fixture FDR

Page 1: NCSX Modular Coil Turning Fixture FDR

NCSX Modular Coil Turning Fixture

FDR

Page 2: NCSX Modular Coil Turning Fixture FDR

FDR Charge(answers were added below after the review)

• Modular Coil Turning Fixture FDR - Charge to Reviewers– The Modular Coil Turning Fixture FDR is the final internal checkpoint before authorizing its

fabrication. Please address the following questions:

• Have the models and drawings defining the turning fixture been checked (reviewed for consistency, completeness, and adherence to drawing standards), and are ready for signature and promotion to Final Design Release Level? Yes.

• Have adequate calculations been performed? Have they been checked? Yes. • Does the winding fixture represent an adequate design solution - i.e., does it provide

an efficient, cost-effective platform for winding all three types of modular coils? Yes. • Recognizing that this is, of necessity, a fixture requiring motion with personnel

working nearby, have the safety aspects been adequately addressed? There will be a safety walk-thru before it is put into operation.

• Is the presented acquisition (manufacturing) plan reasonable? Curreny is to purchase the rings and fabricate the rest in house.

– Is there adequate documentation for the portions which will be outsourced? Yes. Drawings alone are sufficient for procurement of the rings and misc. parts.

– Are the projected costs and schedules consistent with the baseline? Yes.

Page 3: NCSX Modular Coil Turning Fixture FDR

Background

• Modular Coil winding forms are cast structures which provide the foundation on which the coils are constructed.

• Turning Fixtures are used to position the winding surface and are integral components for the preparation, winding and bag molding operations.

• The coil are mounted into a ring which is subsequently placed into the turning fixture frame.

Page 4: NCSX Modular Coil Turning Fixture FDR

Scope

• Winding station requirements, details, operation, loads, stresses, control, power requirements.

• Manufacturing• Safety• Cost & Schedule

Page 5: NCSX Modular Coil Turning Fixture FDR

Requirements of Turning Fixture

• Support modular coils during the prep, winding, molding and VPI tasks.

• Provide simultaneous access to both sides of winding surface.• Provide slow, smooth motion. One rotation to be accomplished in

<10 minutes.• Minimize risk of damaging coil/winding throughout the winding,

molding and VPI tasks.

• Keep design simple, keep costs as low as possible. • Keep footprint as small as possible.

Page 6: NCSX Modular Coil Turning Fixture FDR

A/C Power & Control Requirements

• Coil ring power drive system• 1 hp reversible dc voltage drive motor• 90/180 vdc• variable speed dc motor controller 115/230vac input,• 12.5/6.6amp input current• foot switch for start/stop operation of coil ring

Page 7: NCSX Modular Coil Turning Fixture FDR

Design elements • Frame is constructed of structural steel

– Cheap, strong and easy to work with. Readily available.

• Frame is anchored to test cell floor.

• Turning fixture provides one degree of rotation and access to both sides. An adjustable coil-spool platform (separate design) adjusts to winding surface elevation and angle changes.

• Common “turning” ring is used to support the 3 different types of modular coils via adapter plates.

• Coils are married to one ring throughout their entire winding, molding and VPI process.

• Lots of gearing ensured that coils rotate slowly and under control.

• Top beam removable for lifting of ring/coil assembly out of turning fixture.

Page 8: NCSX Modular Coil Turning Fixture FDR

Design details

• Frame is constructed of MC 10x33.6 structural channel.

• Rings are constructed of MC 12x32.9 structural channel.

• Adapter plates are made from 1” thick steel plate and are mounted to coil flange via bolt/sleeve arrangement.

• Rollers support and guide the ring.• Curved gear rack is welded to the

OD of the ring and is driven by pinion gear.

• Pinion to ring ratio is 7.5:1, gear reducer adds additional 400:1 reduction, giving a total gearing of 3000:1. There are 3,500 ft-lbs available to turn load.

• Foot pedal control for turning the coil. Speed will be adjustable from 0 to 0.5 RPM. Lock-out/tag-out of power will be provided.

Page 9: NCSX Modular Coil Turning Fixture FDR

Loads

• Weight of completed modular coil ~8000#

• Worse case is seismic event. Used (0.13 x 8000#) for seismic loading or ~1000#.

• Applied 8000# vertical load and 1000# horizontal load to frame and calculated reaction loads and moments and stresses.

Page 10: NCSX Modular Coil Turning Fixture FDR

Stresses• Caster/roller wheels rated for 2600-3000# each (per manufacturer)• Max stress at wheel mounting bolts is low. Any 1 bolt can withstand

2000 lb shear load, there are 4 bolts per pad.• Max stress at axles is < 2000 psi shear. This is at the bottom set of

rollers. Side roller axles are under less stress. Material is 1020 CS.• Bolted flange max stress is ~6800 psi, shear on ½-13 bolts.• Max load at any anchor is 170# horiz. (shear) (7400 allow, 28K ult.),

and 1908# tension (vert.) (4600 allow, 17 K ult.)• With outriggers, the force required to overturn is less that the max

seismic loads. Fixture would stay upright even if it were not anchored to floor.

• Max stress in frame is 16.5 ksi. Allowable yield for A36 steel is 36ksi

• Calculations have been checked.

Page 11: NCSX Modular Coil Turning Fixture FDR

Manufacturing• Structural steel used throughout fixture• Low tolerance, simple design features• Minimum of machining – most of the work is cutting/welding.• Rings and ring gear will be fabricated by Lutz.• We will fabricate one fixture in-house and will have the option to

outsource the rest.

Page 12: NCSX Modular Coil Turning Fixture FDR

Operation

• Modular coil rotational speed is 0 to ½ RPM.

• Turning fixture is designed to operate slowly (~1 ft/min) during actual coil winding.

• Generous torque multiplication from gearing ensures that speed remains constant.

• Variable speed control (adjustable by dial) is provided by motor controller.

• Foot pedal (dead-man) provides convenient on/off switch for operators.

Page 13: NCSX Modular Coil Turning Fixture FDR

Safety

• Work will be proceduralized.• JHAs will be generated for operating the turning fixture.• Gears and rollers will have guards (wherever possible) to protect

from hazards. Recommend that we convene a field review of the completed turning fixture with IH prior commissioning for operation.

• Technicians will be trained and be very familiar with the operational hazards.

• Ring will move slowly and technicians will not be working on coil during rotation.

Page 14: NCSX Modular Coil Turning Fixture FDR

Cost and Schedule• Schedule

– March 15 (required for the twisted oval)

• 1 turning fixture and 1 ring.

– June (required for the prototype coils)

• 3 turning fixtures (2 additional) and 2 rings (1 additional).

– November 1 (required for final coils)

• 5 rings (3 additional).• * fourth turning fixture needed if we go with dual winding stations.

• Cost– $283K total budget includes

• 4 complete turning fixtures, 5 rings, 12 sets adapter plates & mounting hardware.

Page 15: NCSX Modular Coil Turning Fixture FDR

Conclusion• Turning fixtures have been designed to accommodate all

the modular coils with a minimum of unique parts. Common fixture used for multiple stations.

• Footprint is reasonably small, minimizing area used. Enclosures would grow for a larger turning fixture.

• “Ring” permanently mounted to coil minimizes handling risks by reducing the number of times that the coil is manipulated.

• Loads and stresses are easily manageable.• Design approach leans to low tech, low tolerance

philosophy, which will keep costs down. Precision machining is minimized. Low-cost materials specified.

Page 16: NCSX Modular Coil Turning Fixture FDR

Drawings

Page 17: NCSX Modular Coil Turning Fixture FDR
Page 18: NCSX Modular Coil Turning Fixture FDR
Page 19: NCSX Modular Coil Turning Fixture FDR
Page 20: NCSX Modular Coil Turning Fixture FDR
Page 21: NCSX Modular Coil Turning Fixture FDR
Page 22: NCSX Modular Coil Turning Fixture FDR
Page 23: NCSX Modular Coil Turning Fixture FDR
Page 24: NCSX Modular Coil Turning Fixture FDR
Page 25: NCSX Modular Coil Turning Fixture FDR
Page 26: NCSX Modular Coil Turning Fixture FDR
Page 27: NCSX Modular Coil Turning Fixture FDR