NB-CPD/SG11-13/005 page 1

Template #1a for a DoP of a reinforced GBR-P

Note: DoPs must be available in the language of the member state. This means a DoP must be translated in up to 27 languages!

Declaration of Performance (DoP) DoP No.: 001CPR/6000/2013-07-14

(running number CPR/certification contract number/yyyy-mm-dd)

1. Product Name: Unique identification code of the product-type:

CoverMembrane L

2. Product Type: Number allowing identification of the construction product as required under Article 11(4) of the CPR:

3200 (lot no. see label and product)

3. Intended use or uses of the construction product, in accordance with the applicable harmonized technical

specification, as foreseen by the manufacturer: for landfill cover lining systems

intended function: barrier

4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under Article 11(5):

Any Co Ltd PO Box 21

1050 Brussels / Belgium Tel +32 123 456789 Fax +32 123 456788

e-mail anyco.sa@provider.be

5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in Article 12(2):

Any Co Ltd PO Box 21

1050 Brussels / Belgium Tel +32 123 456789 Fax +32 123 456788

e-mail anyco.sa@provider.be

6. AVCP: System or systems of assessment and verification of constancy of performance (AVCP) of the construction product as set out in CPR, Annex V:

System 2+

7. Notified body: 1213

In case of the declaration of performance (DoP) concerning a construction product covered by a harmonized standard:

EN 13493:2005

Notified certification body SKZ – TeConA GmbH (iden tification no. 1213) performed the initial inspecti on of the manufacturing plant and of factory productio n control (FPC) and the continuous surveillance,

assessment and evaluation of FPC and issued the cert ificate of conformity of the FPC no. 6000.

NB-CPD/SG11-13/005 page 2

8. Declared performance: Essential characteristics Performance Test standard Harmonised

technical specification

Mean value Tolerance

Tensile strength, F max MD 800 N/5cm - 50 N/5cm EN ISO 527-4 EN 13493:2005 Tensile strength, F max CMD 800 N/5cm - 50 N/5cm EN ISO 527-4 Static puncture resistance, F P 2.7 kN - 0.3 kN EN ISO 12236 Water tightness < 10-6 m³/(m² d) EN 14150 Gas tightness 133 x 10-9 mol/(m² s) ASTM D1434 ESCR npd EN 14576 Weathering resistance,

(350 MJ/m²) can be exposed up to one year EN 12224

Oxidation resistance durable in natural soil with 4<pH<9 and soil temperature <25°C for a minimum of 25 years service life

EN 14575

9. Declaration:

The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 8. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4.

Signed for and on behalf of the manufacturer by:

…………………………………………………………………… (name and function)

…………………………………..…………… …………………………………..…………..

(place and date of issue) (signature)

NB-CPD/SG11-13/005 page 3

Template #1b for a label of a reinforced GBR-P

Note: The label must be available in one language only. A QR-code is a voluntary tool to provide further information in other languages.

1213

Any Co Ltd PO Box 21

1050 Brussels / Belgium Tel +32 123 456789 Fax +32 123 456788

e-mail anyco.sa@provider.be

09

DoP No.: 001CPR/6000/2013-07-14

EN 13493:2005

CoverMembrane L 3200 Intended to be used in landfill cover lining systems

intended function: barrier

Tensile strength , Fmax MD/CMD EN ISO 527-4 800 N/5cm - 80 N/5cm Static puncture resistance, FP EN ISO 12236 2.7 kN - 0.3 kN Water tightness EN 14150 < 10-6 m³/(m² d) Gas tightness ASTM D1434 133 x 10-9 mol/(m² s) Weathering resistance (350 MJ/m²) EN 12224 exposed up to one year

Oxidation resistance EN 14575 durable in natural soil with 4<pH<9 and

soil temperature <25°C for a minimum of 25 years service life

Scan for more product information Roll no.: 04Y25M23D-P06 Nominal gross mass: 380 kg Length: 100 m Width: 2 m Nominal thickness: 2.0 mm (EN ISO 9863-1) Main polymer: LLDPE (100% virgin material) Product description: polymeric geosynthetic barrier

NB-CPD/SG11-13/005 page 4

Template #2a for a DoP of a homogenous GBR-P

Note: DoPs must be available in the language of the member state. This means a DoP must be translated in up to 27 languages!

Declaration of Performance (DoP) DoP No.: 002CPR/6001/2013-07-16

(running number CPR/certification contract number/yyyy-mm-dd)

1. Product Name: Unique identification code of the product-type:

GeoBarrier HD

2. Product Type: Number allowing identification of the construction product as required under Article 11(4) of the CPR:

2.5mm smooth (lot no. see label and product)

3. Intended use or uses of the construction product, in accordance with the applicable harmonized technical

specification, as foreseen by the manufacturer: for liquid waste

intended function: barrier

4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under Article 11(5):

Any Co Ltd PO Box 21

1050 Brussels / Belgium Tel +32 123 456789 Fax +32 123 456788

e-mail anyco.sa@provider.be

5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in Article 12(2):

Any Co Ltd PO Box 21

1050 Brussels / Belgium Tel +32 123 456789 Fax +32 123 456788

e-mail anyco.sa@provider.be

6. AVCP: System or systems of assessment and verification of constancy of performance (AVCP) of the construction product as set out in CPR, Annex V:

System 2+

7. Notified body: 1213

In case of the declaration of performance (DoP) concerning a construction product covered by a harmonized standard:

EN 13492:2004 + A1:2006 Notified certification body SKZ – TeConA GmbH (iden tification no. 1213) performed the initial inspecti on of the

manufacturing plant and of factory production contr ol (FPC) and the continuous surveillance, assessment and evaluation of FPC and issued the certificate of conformity of the FPC no. 6001.

NB-CPD/SG11-13/005 page 5

8. Declared performance: Essential characteristics Performance Test standard Harmonised

technical specification

Mean value Tolerance

Tensile strength, σσσσmax MD 22 N/mm² - 3 N/mm² EN ISO 527-3 EN 13492:2004 + A1:2006 Tensile strength, σσσσmax CMD 22 N/mm² - 3 N/mm² EN ISO 527-3

Static puncture resistance, F P 5.0 kN - 0.6 kN EN ISO 12236 Water tightness < 7x10-7 m³/(m² d) EN 14150 ESCR > 200 h EN 14576 Weathering r esistance

(350 MJ/m²) can be exposed up to one year EN 12224

Oxidation resistance durable in natural soil with 4<pH<9 and soil temperature <25°C for a minimum of 25 years service life

EN 14575

9. Declaration:

The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 8. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4.

Signed for and on behalf of the manufacturer by:

…………………………………………………………………… (name and function)

…………………………………..…………… …………………………………..…………..

(place and date of issue) (signature)

NB-CPD/SG11-13/005 page 6

Template #2b for a label of a homogenous GBR-P

Note: The label must be available in one language only. A QR-code is a voluntary tool to provide further information in other languages.

1213

Any Co Ltd PO Box 21

1050 Brussels / Belgium Tel +32 123 456789 Fax +32 123 456788

e-mail anyco.sa@provider.be

08

DoP No.: 002CPR/6001/2013-07-16

EN 13492:2004 + A1:2006

GeoBarrier HD 2.5 mm smooth Intended to be used used in liquid waste lining systems

intended function: barrier

Tensile strength , σmax MD/CMD EN ISO 527-3 22 MPa - 3 MPa Static puncture resistance, FP EN ISO 12236 2.7 kN - 0.3 kN Water tightness EN 14150 < 7x10-7 m³/(m² d) ESCR EN 14576 > 200 h Weathering resistance (350 MJ/m²) EN 12224 exposed up to one year Oxidation resistance EN 14575 durable in natural soil with 4<pH<9 and

soil temperature <25°C for a minimum of 25 years s ervice life

Scan for more product information Roll no.: SY252323D4-P06 Nominal gross mass: 900 kg Length: 50 m Width: 7 m Nominal thickness: 2.5 mm (EN ISO 9863-1) Main polymer: HDPE (100% virgin material) Product description: polymeric geosynthetic barrier

NB-CPD/SG11-13/005 page 7

Template #3a for a DoP of a drainage geocomposite

Note: DoPs must be available in the language of the member state. This means a DoP must be translated in up to 27 languages!

Declaration of Performance (DoP) DoP No.: 006CPR/6003/2013-07-24

(running number CPR/certification contract number/yyyy-mm-dd)

1. Product Name: Unique identification code of the product-type:

DrainComp

2. Product Type: Number allowing identification of the construction product as required under Article 11(4) of the CPR:

20 (lot no. see label and product)

3. Intended use or uses of the construction product, in accordance with the applicable harmonized technical

specification, as foreseen by the manufacturer: for drainage systems

intended functions: separation (S) , filtration (F), drainage (D)

4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under Article 11(5):

Any Co Ltd PO Box 21

1050 Brussels / Belgium Tel +32 123 456789 Fax +32 123 456788

e-mail anyco.sa@provider.be

5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in Article 12(2):

Any Co Ltd PO Box 21

1050 Brussels / Belgium Tel +32 123 456789 Fax +32 123 456788

e-mail anyco.sa@provider.be

6. AVCP: System or systems of assessment and verification of constancy of performance (AVCP) of the construction product as set out in CPR, Annex V:

System 2+

7. Notified body: 1213

In case of the declaration of performance (DoP) concerning a construction product covered by the harmonized standards:

EN 13252:2000 + A1:2005

Notified certification body SKZ – TeConA GmbH (iden tification no. 1213) performed the initial inspecti on of the manufacturing plant and of factory productio n control (FPC) and the continuous surveillance,

assessment and evaluation of FPC and issued the cert ificate of conformity of the FPC no. 6003.

NB-CPD/SG11-13/005 page 8

8. Declared performance: Essential characteristics Performance Test standard Harmonised

technical specifications

Mean value Tolerance

Tensile strength, T max MD 7 kN/m - 1 kN/m EN ISO 10319 EN 13252:2000 +

A1:2005 Tensile strength, T max CMD 7 kN/m - 1 kN/m EN ISO 10319 Elongation, εεεεmax MD 50% +/- 10% EN ISO 10319 Elongation, εεεεmax CMD 60% +/- 10% EN ISO 10319 Compressive strength 245 kPa - 45 kPa EN ISO 25619-2 Cone drop penetration, D C

(GTX) 30 mm + 2 mm EN ISO 13433

Static puncture resistance, F P

(GTX) 0.8 kN - 0.1 kN EN ISO 12236

Characteristic opening size,O 90 (GTX)

90 µm +/- 20 µm EN ISO 12956

Water flow rate, q N (GTX)

110 l/(m² s) - 10 l/(m² s) EN ISO 11058

Water flow capacity q P 3.4 l/(m s) - 0.4 l/(m s) EN ISO 12958 Weathering resi stance

(50 MJ/m²) can be exposed up to 14 days EN 12224

Oxidation resistance durable in natural soil with 4<pH<9 and soil temperature <25°C for a minimum of 25 years service life

EN ISO 13438, Method C1

9. Declaration:

The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 8. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4.

Signed for and on behalf of the manufacturer by:

…………………………………………………………………… (name and function)

…………………………………..…………… …………………………………..…………..

(place and date of issue) (signature)

NB-CPD/SG11-13/005 page 9

Template #3b for a label of a drainage geocomposite

Note: The label must be available in one language only. A QR-code is a voluntary tool to provide further information in other languages.

1213

Any Co Ltd PO Box 21

1050 Brussels / Belgium Tel +32 123 456789 Fax +32 123 456788

e-mail anyco.sa@provider.be

03

DoP No.: 006CPR/6003/2013-07-24

EN 13252:2000 + A1:2005

DrainComp 20

Intended to be used for roads for drainage systems

intended functions: separation (S) , filtration (F) , drainage (D) Tensile strength, T max MD EN ISO 10319 7 kN/m - 1 kN/m Tensile strength, T max CMD EN ISO 10319 7 kN/m - 1 kN/m Elongation, εεεεmax MD EN ISO 10319 50% +/- 10% Elongation, εεεεmax CMD EN ISO 10319 60% +/- 10% Compressive strength EN ISO 25619-2 245 kPa - 45 kPa Cone drop penetration, D C (GTX) EN ISO 13433 30 mm + 2 mm Static puncture resistance, F P (GTX) EN ISO 12236 0.8 kN - 0.1 kN Characteristic opening size,O 90 (GTX) EN ISO 12956 90 µm +/- 20 µm Water flow rate, q N (GTX) EN ISO 11058 110 l/(m² s) - 10 l/(m² s) Water flow capacity q P EN ISO 12958 3.4 l/(m s) - 0.4 l/(m s) Weathering resistance (50 MJ/m²) EN 12224 can be exposed up to 14 days Oxidation resistance EN ISO 13438,

Method C1 durable in natural soil with 4<pH<9 and soil temperature <25°C for a minimum of 25 years service life

Scan for more product information Lot no.: E899L73 Roll no.: 855123 Nominal gross mass: 75 kg

Length: 30 m Width: 2.5 m

Main polymer(s): HDPE/PP (100% virgin material) Product description: drainage geocomposite

Nominal mass per unit area: 850 g/m² (EN ISO 9864)

NB-CPD/SG11-13/005 page 10

Template #4a for a DoP of a GTX

Note: DoPs must be available in the language of the member state. This means a DoP must be translated in up to 27 languages!

Declaration of Performance (DoP) DoP No.: 003CPR/6002/2013-07-18

(running number CPR/certification contract number/yyyy-mm-dd)

1. Product Name: Unique identification code of the product-type:

GEOFLEECE ABC

2. Product Type: Number allowing identification of the construction product as required under Article 11(4) of the CPR:

1000 (lot no. see label and product)

3. Intended use or uses of the construction product, in accordance with the applicable harmonized technical

specification, as foreseen by the manufacturer: for roads

for tunnels for retaining walls

for drainage systems for reservoirs and dams

for canals intended functions: separation (S) , filtration (F), reinforcement (R)

4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required

under Article 11(5): Any Co Ltd PO Box 21

1050 Brussels / Belgium Tel +32 123 456789 Fax +32 123 456788

e-mail anyco.sa@provider.be

5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in Article 12(2):

Any Co Ltd PO Box 21

1050 Brussels / Belgium Tel +32 123 456789 Fax +32 123 456788

e-mail anyco.sa@provider.be

6. AVCP: System or systems of assessment and verification of constancy of performance (AVCP) of the construction product as set out in CPR, Annex V:

System 2+

7. Notified body: 1213

In case of the declaration of performance (DoP) concerning a construction product covered by the harmonized standards:

EN 13249:2000 + A1:2005 ; EN 13256:2000 + A1:2005 ; EN 13251:2000 + A1:2005 EN 13252:2000 + A1:2005 ; EN 13254:2000 + A1:2005 ; EN 13255:2000 + A1:2005

NB-CPD/SG11-13/005 page 11

Notified certification body SKZ – TeConA GmbH (iden tification no. 1213) performed the initial inspecti on

of the manufacturing plant and of factory productio n control (FPC) and the continuous surveillance, assessment and evaluation of FPC and issued the cert ificate of conformity of the FPC no. 6002.

8. Declared performance: Essential characteristics Performance Test standard Harmonised

technical specifications

Mean value Tolerance

Tensile strength, T max MD 7 kN/m - 1 kN/m EN ISO 10319 EN 13249:2000 + A1:2005

EN 13256:2000 + A1:2005

EN 13251:2000 + A1:2005

EN 13252:2000 + A1:2005

EN 13254:2000 + A1:2005

EN 13255:2000 + A1:2005

Tensile strength, T max CMD 7 kN/m - 1 kN/m EN ISO 10319 Elongation, εεεεmax MD 50% +/- 10% EN ISO 10319 Elongation, εεεεmax CMD 60% +/- 10% EN ISO 10319 Cone drop penetration, D C 30 mm + 2 mm EN ISO 13433 Static puncture resistance, F P 0.8 kN - 0.1 kN EN ISO 12236 Characteri stic opening size,O 90 90 µm +/- 20 µm EN ISO 12956 Water flow rate, q N 110 l/(m² s) - 10 l/(m² s) EN ISO 11058 Weathering resistance

(50 MJ/m²) can be exposed up to one month EN 12224

Oxidation resistance durable in natural soil with 4<pH<9 and soil temperature <25°C for a minimum of 25 years service life

EN ISO 13438, Method C1

9. Declaration:

The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 8. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4.

Signed for and on behalf of the manufacturer by:

…………………………………………………………………… (name and function)

…………………………………..…………… …………………………………..…………..

(place and date of issue) (signature)

NB-CPD/SG11-13/005 page 12

Template #4b for a label of a nonwoven geotextile

Note: The label must be available in one language only. A QR-code is a voluntary tool to provide further information in other languages.

1213

Any Co Ltd PO Box 21

1050 Brussels / Belgium Tel +32 123 456789 Fax +32 123 456788

e-mail anyco.sa@provider.be

02

DoP No.: 003CPR/6002/2013-07-18

EN 13249:2000 + A1:2005 ; EN 13256:2000 + A1:2005 ; EN 13251:2000 + A1:2005 EN 13252:2000 + A1:2005 ; EN 13254:2000 + A1:2005 ; EN 13255:2000 + A1:2005

GEOFLEECE ABC 1000

Intended to be used

for roads , for tunnels , for retaining walls ,

for drainage systems , for reservoirs and dams , for canals intended functions:

separation (S) , filtration (F) , reinforcement (R) Tensile strength , Tmax MD/CMD EN ISO 10319 7 kN/m - 1 kN/m Elongation , εmax MD/CMD EN ISO 10319 50% +/- 10% Cone drop penetration, D C EN ISO 13433 30 mm + 2 mm Static puncture resistance, FP EN ISO 12236 0.8 kN - 0.1 kN Characteristic opening size,O 90 EN ISO 12956 90 µm +/- 20 µm Water flow rate, q N EN ISO 11058 110 l/(m² s) - 10 l/(m² s) Weathering resistance (50 MJ/m²) EN 12224 exposed up to one month Oxidation resistance EN ISO 13438, durable in natural soil with 4<pH<9 and soil temperature <25°C

Method C1 for a minimum of 25 years service life

Scan for more product information Lot no.: 89934573 Roll no.: 123 Nominal gross mass: 175 kg Length: 200 m Width: 5 m Nominal mass per unit area: 170 g/m² (EN ISO 9864) Main polymer: PP (100% virgin material) Product description: nonwoven geotextile

NB-CPD/SG11-13/005 page 13

NB-CPD/SG11-13/005 page 14

Template #5a for a DoP of a waterproofing sheet for roofing

Note: DoPs must be available in the language of the member state. This means a DoP must be translated in up to 27 languages!

Declaration of Performance (DoP) DoP No.: 004CPR/7001/2013-07-20

(running number CPR/certification contract number/yyyy-mm-dd)

1. Product Name: Unique identification code of the product-type:

RoofPlan TPO

2. Product Type: Number allowing identification of the construction product as required under Article 11(4) of the CPR:

1,8 (lot no. see label and product)

3. Intended use or uses of the construction product, in accordance with the applicable harmonized technical

specification, as foreseen by the manufacturer: for roof waterproofing for exposed mechanically fas tened flat roof systems

4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required

under Article 11(5): Any Co Ltd PO Box 21

1050 Brussels / Belgium Tel +32 123 456789 Fax +32 123 456788

e-mail anyco.sa@provider.be

5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in Article 12(2):

Any Co Ltd PO Box 21

1050 Brussels / Belgium Tel +32 123 456789 Fax +32 123 456788

e-mail anyco.sa@provider.be

6. AVCP: System or systems of assessment and verification of constancy of performance (AVCP) of the construction product as set out in CPR, Annex V:

System 2+

7. Notified body: 1213

In case of the declaration of performance (DoP) concerning a construction product covered by the harmonized standard:

EN 13956:2012

Notified certification body SKZ – TeConA GmbH (iden tification no. 1213) performed the initial inspecti on of the manufacturing plant and of factory productio n control (FPC) and the continuous surveillance,

assessment and evaluation of FPC and issued the cert ificate of conformity of the FPC no. 7001.

NB-CPD/SG11-13/005 page 15

8. Declared performance: Essential characteristics Performance Test standard Harmonised

technical specification

water tightness pass EN 1928, Method B EN 13956:2012 external fire performance Class Broof (t1) <20° EN 13501-5

reaction to fire Class E EN ISO 11925-2, classification to EN 13501-1

tensile strength MD/CMD ≥1800 N/50mm EN 12311-2 elongation MD/CMD ≥30% EN 12311-2 resistance to tearing MD/CMD ≥600 N / ≥800 N EN 12310-2 foldability at low temperatur e ≤ -40 °C EN 495-5 joint peel resistance ≥400 N/50mm EN 12316-2 joint tensile shear resistance ≥1200 N/50mm EN 12317-2 UV resistance npd EN 1297 9. Declaration:

The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 8. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4.

Signed for and on behalf of the manufacturer by:

…………………………………………………………………… (name and function)

…………………………………..…………… …………………………………..…………..

(place and date of issue) (signature)

NB-CPD/SG11-13/005 page 16

Template 5b for a label of a waterproofing sheet for roofing

Note: The label must be available in one language only. A QR-code is a voluntary tool to provide further information in other languages.

1213

Any Co Ltd PO Box 21

1050 Brussels / Belgium Tel +32 123 456789 Fax +32 123 456788

e-mail anyco.sa@provider.be

07

DoP No.: 004CPR/7001/2013-07-20

EN 13956:2012

RoofPlan TPO 1,8 Intended to be used

for roof waterproofing for exposed mechanically fas tened flat roof systems water tightness EN 1928, Method B pass external fire performance EN 13501-5 Class Broof (t1) <20° reaction to fire EN ISO 11925-2,

classification to EN 13501-1 Class E

tensile strength MD/CMD EN 12311-2 ≥1800 N/50mm elongation MD/CMD EN 12311-2 ≥30% resistance to tearing MD/CMD EN 12310-2 ≥600 N / ≥800 N foldability at low temperature EN 495-5 ≤ -40 °C joint peel resistance EN 12316-2 ≥400 N/50mm joint tensile shear resistance EN 12317-2 ≥1200 N/50mm

Scan for more product information Lot no.: 8F5621-445-96 Roll no.: 454123 Length: 25 m Width: 3 m

NB-CPD/SG11-13/005 page 17

Template #6a for a DoP of a dimpled sheet for waterproofing

Note: DoPs must be available in the language of the member state. This means a DoP must be translated in up to 27 languages!

Declaration of Performance (DoP) DoP No.: 005CPR/7002/2013-07-22

(running number CPR/certification contract number/yyyy-mm-dd)

1. Product Name: Unique identification code of the product-type:

CuspDrain 8 dia

2. Product Type: Number allowing identification of the construction product as required under Article 11(4) of the CPR:

600 (lot no. see label and product)

3. Intended use or uses of the construction product, in accordance with the applicable harmonized technical

specification, as foreseen by the manufacturer: for damp proof sheets, type V

4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required

under Article 11(5): Any Co Ltd PO Box 21

1050 Brussels / Belgium Tel +32 123 456789 Fax +32 123 456788

e-mail anyco.sa@provider.be

5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in Article 12(2):

Any Co Ltd PO Box 21

1050 Brussels / Belgium Tel +32 123 456789 Fax +32 123 456788

e-mail anyco.sa@provider.be

6. AVCP: System or systems of assessment and verification of constancy of performance (AVCP) of the construction product as set out in CPR, Annex V:

System 2+

7. Notified body: 1213

In case of the declaration of performance (DoP) concerning a construction product covered by the harmonized standard:

EN 13967:2012

Notified certification body SKZ – TeConA GmbH (iden tification no. 1213) performed the initial inspecti on of the manufacturing plant and of factory productio n control (FPC) and the continuous surveillance,

assessment and evaluation of FPC and issued the cert ificate of conformity of the FPC no. 7002.

NB-CPD/SG11-13/005 page 18

8. Declared performance: Essential characteristics Performance Test standard Harmonised

technical specification

Water tightness (60 kPa, 24 h) pass EN 1928, EN 13967:2012 Tear resistance MD >316 N EN 12310-1

Tear resistance CMD >353 N EN 12310-1 Joint tensile shear resistance npd EN 12317-2 Resistance to impact npd EN 12691-2, Method A Tensile strength MD/CMD npd EN 12311-2 Elongation MD/CMD npd EN 12311-2 Resistance to static load npd EN 12730 Reaction to fire Class F EN ISO 11925-2,

classification to EN 13501-1 Resistance against ageing npd EN 1296 / EN 1928 Chemical resistance npd EN 1847 / EN 1928 9. Declaration:

The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 8. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4.

Signed for and on behalf of the manufacturer by:

…………………………………………………………………… (name and function)

…………………………………..…………… …………………………………..…………..

(place and date of issue) (signature)

NB-CPD/SG11-13/005 page 19

Template #6b for a label of a dimpled sheet for waterproofing

Note: The label must be available in one language only. A QR-code is a voluntary tool to provide further information in other languages.

1213

Any Co Ltd PO Box 21

1050 Brussels / Belgium Tel +32 123 456789 Fax +32 123 456788

e-mail anyco.sa@provider.be (or identifying mark)

09

DoP No.: 005CPR/7002/2013-07-22

EN 13967:2012

CuspDrain 8 dia 600

(unique identification code) Intended to be used for damp proof sheets, type V Water tightness (60 kPa, 24 h) EN 1928, pass Tear resistance MD EN 12310-1 >316 N Tear resistance CMD EN 12310-1 >353 N

Scan for more product information Lot no.: H4E8-56 Roll no.: 23 Length: 15 m Width: 2 m

NB-CPD/SG11-13/005 page 20

Template #7a for a DoP of a plastic vapour control layer

Note: DoPs must be available in the language of the member state. This means a DoP must be translated in up to 27 languages!

Declaration of Performance (DoP) DoP No.: 006CPR2013-08-02

(running number CPR yyyy-mm-dd)

1. Product Name: Unique identification code of the product-type:

VapourFoil PE blue

2. Product Type: Number allowing identification of the construction product as required under Article 11(4) of the CPR:

130 (lot no. see label and product)

3. Intended use or uses of the construction product, in accordance with the applicable harmonized technical

specification, as foreseen by the manufacturer: for vapour control, type A

4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required

under Article 11(5): Any Co Ltd PO Box 21

1050 Brussels / Belgium Tel +32 123 456789 Fax +32 123 456788

e-mail anyco.sa@provider.be

5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in Article 12(2):

Any Co Ltd PO Box 21

1050 Brussels / Belgium Tel +32 123 456789 Fax +32 123 456788

e-mail anyco.sa@provider.be

6. AVCP: System or systems of assessment and verification of constancy of performance (AVCP) of the construction product as set out in CPR, Annex V:

System 3

7. Notified body/bodies: 1213 / nnn1

In case of the declaration of performance (DoP) concerning a construction product covered by the harmonized standard:

EN 13984:2013

Notified test laboratory SKZ – TeConA GmbH (identifi cation no. 1213) performed the product type determination (PTD) on wa ter tightness and water vapour resistance.

Notified test laboratory FIRE-Test Ltd (identificat ion no. nnn1) performed the PTD on reaction to fire.

NB-CPD/SG11-13/005 page 21

8. Declared performance: Essential characteristics Performance Test standard Harmonised technical

specification

Water tightness Pass EN 1928, Method A (2 kPa, 24 h)

EN 13984:2013

Resistance to impact npd EN 12691 Water vapour resistance after ageing

(water vapour diffusion equivalent air layer thickness s d)

95 m EN 13984 / EN 1931

Chemical resistance npd EN 1847 / EN 12311-2 Tear resistance MD/CMD 50 N EN 12310-1 Joint tensile shear resistance npd EN 12317-2 Water vapour resistance

(water vapour diffusion equivalent air layer thickness s d)

100 m EN 1931

Tensile strength MD/CMD ≥100 N/50mm EN 12311-2 Elongation MD/CMD ≥250% EN 12311-2 Reaction to fire Class E EN ISO 11925-2,

classification to EN 13501-1

9. Declaration:

The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 8. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4.

Signed for and on behalf of the manufacturer by:

…………………………………………………………………… (name and function)

…………………………………..…………… …………………………………..…………..

(place and date of issue) (signature)

NB-CPD/SG11-13/005 page 22

Template 7b for a label of a plastic vapour control layer

Note: The label must be available in one language only. A QR-code is a voluntary tool to provide further information in other languages.

1213 / nnn1

Any Co Ltd PO Box 21

1050 Brussels / Belgium Tel +32 123 456789 Fax +32 123 456788

e-mail anyco.sa@provider.be (or identifying mark)

08

DoP No.: 006CPR2013-08-02

EN 13984:2013

VapourFoil PE blue 130

(unique identification code) Intended to be used for vapour control, type A Water tightness EN 1928, Method A (2 kPa, 24 h) Pass Water va pour resistance after ageing

(water vapour diffusion equivalent air layer thickn ess s d) EN 13984 / EN 1931 95 m

Tear resistance MD/CMD EN 12310-1 50 N Water vapour resistance

(water vapour diffusion equivalent air layer thickn ess s d) EN 1931 100 m

Tensile strength MD/CMD EN 12311-2 ≥100 N/50mm Elongation MD/CMD EN 12311-2 ≥250% Reaction to fire EN ISO 11925-2,

classification to EN 13501-1 Class E

Scan for more product information Lot no.: 8FF621-4L5-96 Roll no.: 45K41Z23 Length: 40 m Width: 2 m