Name ZJ50D(S102) Make Kerui, China Type - ADSO · Drawworks Power (hp) 1500 HP powered by 2 x750 hp...

Item Description of Proposed Equipment

Drilling Unit Details

Name ZJ50D(S102)

Make Kerui, China

Type1500 HP SCR

Year of construction 2013

Current location Sharjah, United Arab Emirates

Current Condition i.e. stacked or operational stacked

Currently contracted to which COMPANY

Average fuel consumption while drilling 6000l/day

Average oil consumption while drilling 36 kg/DAY

Nominal drilling depth with 5” DP (m) 4500m

Nominal drilling depth with 3.1/2" DP (m) 5500m

Rig Fuel capacity 315bbl

Active System liquid mud pit working capacity 1720bbl

Liquid mud reserve pit working capacity 980bbl

Rig Water Pits / tanks 1000bbl (2 x 500bbl)

Schematic diagram of proposed rig mud tank layout yes

Mud sack capacity in covered area (sx)

Casing-rack load capacity (lb) 660,000 Ibs

Drillpipe Rack load capacity 700,000 lbs

Draw-works Details

Make Kerui, JC50D

Rated input power (hp) 1,500 HP

Line Diameter (inches) 1 3/8"(35mm),

Drive type2 Ea x 750 HP (800 KW) Motors

Auxiliary brake type PUSHIKE, PS165/3150D

Brake cooling system capacity (bbl) 40M3(250BBL)

Automatic emergency brake (solenoid valve) with alarm and

lightYes, Hydrulic

No. of strung lines 6

Maximum peak hoisting load (lb) (900,000 lbs)

Maximum operating hoisting load (lb) (700,000 lbs)

Catheads spinning/breakout type hydraulic

Crown block safety device type Yes, Bomco Electric Type

Automatic driller type N/A

Ezytorque type Yes, cathead

Item Description of proposed Equipment

Rig Specification

Mast Specifications

Make and type Kerui JJ450/45-k

Total height (m) 149 ft clear Hight (45.5m)

Height from ground level (m) 182 ft(55.5m)

Stands racked in doubles or triples Triples

API gross nominal capacity (Ib) (As per API Sepc.4F definition) 450 Ton

API static peak hookload capacity (Ib)

API static continuous operating hookload capacity (Ib) 1,000,000lbs

Casing stabbing board-air operated with safety locking device and

secured on top and bottom yes

Casing stabbing board-adjustable range (m) 6m-15m

Dead line anchor type Jianghan, JZG41

Dead line anchor capacity 41 ton

Crown block make and type Kerui, TC450

Crown block rated capacity (Ib) 1,200,000Ibs(4500KN)

Racking system make and type Kerui, c/w 0.5 Air Winch

Racking system capacity of 5” drill-pipe (m) 20,000 ft (6000m)

Racking system capacity of 5” drill pipe with additional 3.1/2” drill

pipe20,000 ft (6000m)

Air winch with spooling device –make & type tai"an, china, XJFH-5/35

Air winch rated pull (mT) 5 Ton

Air winch position Rig Floor


Sub-Structure

Make and typeKerui, DZ450/10.5-X

Dimensions (m)10.5m * 13.9m * 12.65m

Rig floor height (m)35 ft (10.67m)

Clear height beneath rotary beams30 ft

Nominal height (m)35 ft (10.5m)

Simultaneous setback capacity (Ib)600,000Ibs(2700KN)

Simultaneous casing (rotary) capacity (Ib)1,000,000 Ibs(2700KN)

Combined casing and setback capacity (Ib)1,200,000 lbs

Matting boardsyes

Accessories yes

Air tanks 2ea * 2000lt,2500lt

BOP handling system yes

BOP handling system load capacity (Ib) 2 x 25 mt (2 x 55,000lb)

Air winch mounted in wellhead area yes

Air winch rated pull (Ib) 5,000lb

Air winch position rig floor

Height underneath rotary beams (m) 30ft ( 9.14m)

Catwalk length (m) 50ft ( 15.24m)


Travelling Assembly

Block make and typeKerui, YC315

Rated capacity (lb) 1,000,000 Ibs(4500KN)

Rig Specification

Hook make and type LS, DG315

Rated capacity (lb) 750,000 Ibs(3150KN)

Swivel make and type* LS, SL450-II(with air spinner)

Swivel pressure rating (psi) 5,000 PSI

Rated capacity (lb) 1,000,000 Ibs(4500KN)

Top Drive

Manufacturer NOV, USA ,Varco

Type TDS-11SA

Rated capacity (lb) 1,200,000 lbs

Drive type 2 Ea AC Motor

Input Power rating (hp) 2 X 400 HP

Maximum torque (ftlb) 75,000 ft.lb

Maximum continuous torque (ftlb) 35,000lb.ft

Maximum rpm 228

Rpm at maximum continuous torque 228 @ 0 torque

Drilling Speed (rpm) 228

Water Course & CWP yes

Pipe Handler : yes

Make varco

Type PH75

Torque Capacity 55,000lb

Drillpipe Range 3 1/2"-5"

Upper IBOP 6 5/8" API Reg.RH, Box and Pin

Lower IBOP yes ( manual)

IBOP Pressure Rating (psi) 10000psi

Drill Line

Drill line make 6 * 19S+IWRC EIPS

Drill line size (in) 1 3/8"

Drill line breaking strength (lb) 188,000Lb

Length on reel 4000 ft

Sandline present n/a

Sandline size (in)

Sandline length (m)


Drill Unit Transport

Total number of truck loads 100 incl camp

Number of truck loads in excess of 15m (total length) by 3.25m

(maximum width)10 truck &20 truck

Telescopic Mast 5 truck

Detailed load list with Bid illustrating dimensions and weight of all

loadsyes, packing list attached

Rig Specification

Rotary Equipment

Rotary Table

Manufacturer Kerui

Type ZP 375

Rated static capacity (lb)1,300,000 lbs

Maximum opening size (in) 37.5"

Drive typeYZ08B DC - Motor

Maximum input horsepower (hp)1000 HP

Inserts (in)3-1/2 to 30

Right and left torque limit (ftlb) 33,000 lbs.ft

Maximum rpm 300RPM

Bit Breaker master plate yes

Pumping and High Pressure Discharge System

Mud Pumps

Number 2 Ea

Make Bomco

Type F-1600

Drive DC - Motor

Maximum input horsepower per pump (hp)1600 HP

Maximum continuous pressure rating with 2 pumps (psi) 5,000 PSI

Maximum continuous flowrate with 2 pumps (gpm)1,200 gpm

Fluid end type Bomco

Liner sizes available (in) 5" & 5-1/2" & 6" & 6-1/2" & 7"

Pulsation dampener type bomco , 1 Ea Per Pump KB-75

Reset relief valve type bomco , 1 Ea Per Pump

High pressure valve(s) after pump yes

Charge pump make and type 1 ea Per Pump -mission

Charge pump drive 100 HP

Charge pump impeller OD (in) HCP6" x 8" x 13"

Capability to charge any mud pump yes

Rig Specification


Suction lines - number and size (in) 0ne per pump, 10"

Suction dampeners - number and type bomco , 1 Ea Per Pump

High Pressure Mud LinesDischarge line number

2

Discharge line size, OD X ID (in) 5" ID W/Fitted WP 5,000 PSI

Working pressure 5,000 PSI

Rotary hose number and type2 Ea (one spare) (certified & tested.)

Rotary hose size (in) 4" ID W/union 1002 WP 5,000 PSI

Rotary hose length (m) 75 Ft, 62FT

Rotary hose working pressure (psi) 5000 PSI

Standpipe number 2 Ea

Standpipe size (in) 5" OD & 4" ID

Standpipe working pressure (psi) 5,000 PSI

Mud manifold configuration drawing yes

Cementing Line and StandpipeFlexible hose cementing line

yes

Separate cementing standpipe

Cementing standpipe working pressure 5,000 psi

Low Pressure Mud System

Mud Mixing

Mixing hopper number2 Ea

Hopper make and type TSC

Facility to handle 1000kg bags Yes

Mixing pumps number 2 Ea

Mixing pump make and type TSC

Location On Reserve Tank

Drive Electric Power

Independent suction line Yes

Discharge line sizes6" OD

Mixing facilities Yes

Maximum pump rate possible when mixing and increasing mud

density by 1.0 ppg (gpm)1200 gpm

Caustic mixing facilities Yes

Mud guns 1Ea

Rig Specification


Shale Shaker

Number3 Ea+1 under mud cleaner

TypeDerrick FLC-503-3 panel , suitable for Oil and Water

Based Mud at flow-rates of 1,500 gpm

Drive 2 EaVibrator Motors Electric Drive

Screen type Pyramid Type

Effective screen area (per deck) (m2) 2 Ea x 697x1053mm

Screen sizescharged on client

DesanderMake and type Derrick FLC -503 , combind desander&mud cleaner on

shale shaker

Number of cones 3 Ea

Cone size (in) 10 inch

Feed pump make (fully assigned) USA

Feed pump type Mission

Feed pump drive Electric Motor 75 HP

Suction from Shale Shaker Tank

Discharge to Intermediate Tank

DesliterMake and type

Derrick FLC -503

Number of cones 16

Cone size (in) 4"

Feed pump make (fully assigned) USA

Feed pump type Mission




Mud Cleaner

Make and type Derrick FLC-503 , combind desander&mud cleaner on

shale shaker

Number of cones 16 Ea

Cone size (in) 4" inch

Feed pump make (fully assigned) TSC

Feed pump type HCP6" x 8" x 13"


Screen mesh size charged on client




Rig Specification

Centrifuge

Make and type call out

Mud Tanks

Total capacity excluding sandtraps (bbl) 2,700 BBL

Total number of mud tanks including sandtraps 6 Tanks

Active capacity (bbl) Including settling tanks and sandtraps 1720 bbl

Number of active tanks 4 Ea

Reserve mud capacity (bbl) 980 bbl

Number of reserve tanks 2 Ea

Chemical Mixing capacity (bbl) 1 ea x 30 bbl

Trip tank (API) 60 bbl

Number of chemical mixing tanks 1 Ea+ mixing reverse tank

Number of pill tanks 1 Ea

Pill capacity (bbl) 60 bbl

Extra details

A 2" water supply line are installed on all mixing and suction tanks

A 2” Diesel / base oil supply line are installed on all mixing and

suction tanks

Mud tanks are suitably covered with gratings to avoid accidents yes

Overflows are fitted between active pits yes

Mud tanks are equipped with mud agitators yes

Dump valves 12" yes

All electric motors and panels in the mud tanks area yes

Trip Tank

Capacity (bbl) 60 bbl

Fill method Centerfugal Pump 2x3x13

Pump type HCP3 *2

Level indicator type Mechanical

Tank position relative to flowline & bell nipple part of rig mud system

Water TanksNumber of drill water tanks 2 Ea

Capacity (bbl) 1000 BBL

Number of drinking water tanks 2 Ea ( one in site camp & one in Main Camp


Number of water pumps 2 Ea

Water pump type and size Kerui, 2" *3" centrifugal water pumps

Line size (in) 3"

Rig Specification


Line lengths (m) part of rig mud system

Caller Pump as required

Number 1 Ea

Type/capacity (gpm) (electric submersible) Mission- Centerfugel pump 2*3*13-1000gpm

Mud AgitatorsNumber

(14), One (1) per compartment plus two (2) spares

Typeswaco

Motor (hp) 15 HP

Casing Fill-up Line

Make and type Call Out

OD (in)

Location

Controls (must not be run off HP mud pump)

Well Fill-up Line

Make and type 2" Hose 40 ft x 5,000 PSI

OD (in) Flexiable hose

Location 2"

Controls Gate Valve

Other Mud Equipment Centrifugal pump(s) and lines to allow pumping mix water to

cement unit yes

Mud BucketOne (1) for 5" & 3-1/2" DP

Mud saver Valves yes

Power Plant

Prime Movers

Number of diesel engines3+ 1 ea rmergency generator

Manufacturer(s) Caterpillar

Type(s)Cat 3512B

Total Power (hp) 4500 HP, 1500 HP Per Each

Drawworks Power (hp) 1500 HP powered by 2 x750 hp dc motor

Mud Pumps Power (hp) 2 X 1600 Hp powered by 4 x 1100 hp dc motor

Speed (rpm) 1500 rpm / engine

Mechanical Drive System

Number of torque converters Not applicable

Rig Specification


Electric Drive System

Number of AC generators 3 Ea

Manufacturer Caterpillar

Type Cat - SR4B

Power output (hp) / Volts (V) 1900 kVA & 1020 ekW

Speed (rpm) 1500 rpm

SCR System

Quantity / Number of Bays 4 each SCR Cabinent

Make HHCT

Type RH

Maximum continuous power (kW) 1600 KW

DC output volts (V) 750 V DC

Lines and Switchboards

All lines to be protected. Control panel with breaker switches and

transformers included

Yes

All electric fittings to be explosion proofYes

Third Party Power AvailabilityMaximum continuous power (kVA)

100 kva

Output volts (v) 380/220 volt

Fuel Tanks

Number 1 Ea


Emergency Generators Quantity (must be automatic start)

C15

Maximum continuous power (kVA)400kw

Output volts (V) 400v

Frequency (hz) 50Hz

Blowout Prevention and Well Control Equipment

Diverter System

29 1/2" Diverter system is rated to 500 psi with 12" valves side

outletsN/A


Large Service BOP StackGeneral Description for 21.1/4" BOP stack

20 3/4" 3M BOP Stack Out on rental baseae

Number of separate inlets / outlets 2 Ea

Side outlet size (in) and connection ea 4 1/8"

Rig Specification

Side outlet working pressure (psi) 3000Psi

Location of inlets / outlets on body at closing unit side

Annular make and size (in)hydrill 20 3/4"-3M

Annular ID (in) 20 3/4"

Annular working pressure (psi) 3000 psi

Top connection with ring gasket yes

Bottom connection with ring gasket yes

Date annular element last replaced new

Annular element elastomer type Hydrilll

Date of last repair or re-manufacture new

Ram preventer make and type (in) Rongsheng Double Rame

Ram preventer body size (in) 20-3/4"

Ram preventer working pressure (psi) 3000psi

Ram preventer ID (in) 20-3/4"



Ram sizes (in) 1 set Blind/shearing rams&2sets 5"d/p rams& 1set 13 3/8"

casing rams

Ram packers and seals elastomer typeRongsheng

Date ram packers and seals last replaced new

Ram lock type hydrulic

Ram preventers fitted with extension hand wheels yes

All components suitable for H2S service yes


Rig Specification

Stack-up drawing to be included yes

13.5/8" BOP Stack

General description of 13.5/8" One 13-5/8" BOP strack,10,000 WP suitable for H2S service

Number of separate inlets / outlets two

Side outlet size (in) and connection 4-1/16"

Side outlet working pressure (psi) 10,000 PSI

Location of inlets / outlets on body at closing unit side

Annular make and size (in) RS, FH35-35/70, Size 13-5/8"

Annular ID (in) 13-5/8"

Annular working pressure (psi) 5K psi 10000 psi

Top connection with ring gasket yes(STUDDED/13 5/8"-5000PSI)


Date annular element last replaced New

Annular element elastomer type RS

Date of last repair or re-manufacture New

Ram preventer make and type (in) RS, One Double Ram&One Single rame

Ram preventer body size (in) Size 13-5/8"

Ram preventer working pressure (psi) 10,000 PSI

Ram preventer ID (in) 13-5/8"



Ram sizes (in) include one Blind/Shear rams, one 9.5/8” casing ram, one

7” casing ramone sets pipe rams 5" , one sets pipe rams

3-1/2"&one sets pipe rames 2 3/8"

Ram packers and seals elastomer type RS, Suitable for 300 deg F and oil base mud

Date ram packers and seals last replaced new

Ram lock type hydrulic

Ram preventers fitted with extension hand wheels yes

All components suitable for H2S service yes


Stack-up drawing to be included yes attached in end of this appendix

Drilling Spools

The well head configuration is to be confirmed Yes

Accumulator Unit

MakeYancheng Sanyi FKQ 800-7

Type FKQ 800-7

Hydraulic fluid reservoir capacity (gal) 1650 L (440 gal)

Hydraulic fluid type AW 46 Hyd oil

Number of bottles 20 each 10.5 Gallons Bottles

Rig Specification

Precharge pressure (psi) 1000 PSI

Rig Specification


choke

63 gallons

Total fluid volume required to close all preventers on 13.5/8", 10M

BOP Stack (gal)

42.570 Gallons

Time to close any ram preventer (sec)30 Second

Time to close annular preventer (sec)45 Second

BOP Control System

Charge pump type (2) air pump + One(1) electrical pump Triplex

Charge pump capacity (gpm and psi) 3.2 gal 1 min & 6-25 gal 1 min

Charge time from precharge to 3000 psi (mins) 10 min

Charge pump power sourceair & electric source

Main panel location in accumulator unit

Main panel alarms N/A

Remote panel location 1 Ea on Rig Floor & 1 Panel at Toolpusher office

Choke ManifoldMinimum bore (in)

3-1/8"

Rated working pressure (psi) 10,000 PSI

Date of last wall thickness check New


Gauge range (psi) Gauge manifold w/ 1000, 2000, & 5000 psi valves

Date of last gauge calibration New

Back-up gauge range (psi) 0 - 10,000 psi

Date of last gauge calibration New

Bypass (yes/no - give details)yes

Number of chokes 2

Manual Choke type RS

Choke size (in) 3-1/8"

Choke working pressure (psi) 10,000 psi

Automatic Choke type Swaco

Choke size (in) 3-1/8"

Location of remote hydraulic actuator on Rig Floor

Choke working pressure (psi)10,000 psi

Number of outlets after buffer chamber required as follows:

1 to the waste pit yes

1 to the horizontal vent line yes

1 to the atmospheric gas separator yes

1 to the Shale Shakers yes

Rig Specification


Choke LinesNumber

1 line

Type –safety chains must be provided Yes

Size (in) 3-1/8"

Rated working pressure (psi) 10,000 psi

Number of valves 2

Valve typeCameron or Equival

Valve configuration1 hydraulically actuated with manual override and 1

manual valve

Valve size (in)3-1/8"

Valve pressure rating (psi) 10,000 psi

Valve connection flanged w/ ring gasket

Valve actuator typeHydrulic


Kill Lines

Number 1 Line

Type High pressure wing union/elbows (weco 2", fig.1502)

Size (in) 2-1/16"

Rated working pressure (psi) 10,000 psi

Number of valves 2

Valve type Cameron or equvalent

Valve configuration 1 manual gate valves and 1 non-return valve

Valve size 2-1/16"

Valve pressure rating (psi) 10,000 psi

Valve connection flanged w/ring gasket

Valve actuator type manual


Emergency Line (From cementing unit to wellhead inlet)

Number as required

Rig Specification


BOP Testing and Handling Equipment as required

Cup testers20", 13 3/8", 9 5/5", 7" Weights TBA

Number 1Ea/ each size

Type TBA

Body diameter (in)

as required

Cup tester size (in)20", 13 3/8", 9 5/5", 7"

Test sub size (in) and connections 4 1/2" IF

Test stumps for testing all BOPs prior to spud and prior to

installing on well head.

YES

Pneumatic BOP handling trolley below rotary beams for moving

complete stack between test stump and substructure

Hydrulic LiftingBOP handling Equipment

Make and type Baoij Engineering / FY 50 Y

Power supply

Hydrulic

Range60 ton

Accessoriesindpentant controlpanel

String Safety Valves (Gray Valve)

Two each to fit each dp size with cross-overs to DC connections. Gray

Make tow/(2) each for d/p

Type ITAG or equivelant

Connection 4 1/2 IF, 3 1/2"IF

Rated working pressure (psi) 10,000psi

Upper Kelly Cock

Number 2Ea

Lower Kelly Cock

Number 2Ea

Drop-in Check Valves (Dart subs)

Dart subs for 5" drill pipe N/A

Float Valves

All DC sizes provided. Are full opening BAKER type, AND

PORTED FOR PRESSURE MONITORING.1Ea/ each size, Baker types 5F-6R,4F-4R, 2F-3R

Rated working pressure (psi) 10,000psi

Bell Nipples

Adjustable for 13 5/8" and 21.1/4” stacks yes

Vent Lines from Mud Gas Separator


Rig Specification

Number

1 Ea

Size (in) 8"

Length (m)

30'

Locationbeside waste pool

Mud Gas Separator

Make CHINA

Type Vertical 48" OD(poor boy)

Inlet line size (in) 8"

Outlet line size (in) 10"

Gas discharge point Vent line to crown

Maximum process capacity of mud 300M^3/h(1880 gpm)

Maximum process capacity of gas 4600CFM gas

Bypass (yes/no) yes

Mud head (ft) 10 ft

Functioning relief valve (yes/no) yes

Diagram must be provided yes attached ______________________________>

Vacuum Degasser

Make

Derrick

Type

Derrick FLC-503-3 panel

Feed pump type Centrifugal HCP 6 *8 *13

Feed pump drive 75 HP

Suction from shal shaker tank

Discharge to desander tank

Gas discharge pointwaste pool

Process capacity at 11.6 ppg mud density (gpm) yes


Rig Floor Equipment

Elevators

Rig Specification

Centre Latch/Side Door Drill Pipe & Drill Collar

For 5" drill pipe – quantity2Ea

Make BJ-Varco

Type center latch

Capacity (mt)350MT

For 3.1/2" drill pipe - quantity 2Ea

Quantity BJ-Varco

Make center latch

Capacity (mt) 250MT

Rig Specification


For Drill collars – Quantity for all sizes Lifiting subs

Sizes (in) 9-1/2 D/C & 8-1/4 & 6 1/2" &4-3/4"d/c

Type

Capacity (mt)

Casing Side Door Elevators

For casing sizes 20”, 18.5/8”, 16”, 14”, 13.3/8", 11 7/8”, 10.3/4”,

9.5/8", 7", 5.1/2”, 5”, 4.1/2”, 3.1/2”to be supplied on call out Basis

Quantity

Make

Sizes (in)

Type

Capacity (mt)

Casing Spiders to be supplied on call out Basis

Quantity

Single Joint Elevators to be supplied on call out Basis

For casing sizes 20”, 18.5/8”, 16”, 14”, 13.3/8", 11 7/8”, 10.3/4”,

9.5/8", 7", 5.1/2”, 5”, 4.1/2”, 3.1/2”

Elevator Links“Quick-lift” elevator for drill collars - quantity

1Ea 2-3/4"*132

Capacity (m) 350 MT

Weldless links, 2 3/4” x 18 meters – Quantity1Ea 3-1/3"*192" F /Run casing

Capacity (m) 500MT

Slip Requirements

Manual Slips

5" drill pipe – quantity 2 Ea

MakeVarco

TypeSDXL Hand slips

Capacity (mt) as Per API Standard

3.1/2" drill pipe – quantity 2 Ea

Make Varco

TypeSDXL Hand slips

Capacity (mt) as Per API Standard

Drill collars – Quantity for all sizes providedyes

Make Varco

Sizes (in) 9-1/2" & 8-1/4" & 6-1/2" & 4-3/4"

Rig Specification


Type

DSC Hand slips

Capacity (m)as Per API Standard

Casing Slips and Casing Bowls for Master Bushings to be supplied on call out Basis

For casing sizes 20”, 18.5/8”, 16”, 14”, 13.3/8", 11 7/8”, 10.3/4”,

9.5/8", 7", 5.1/2”, 5”, 4.1/2”, 3.1/2”

Safety Clamps

To grip sizes 3.1/2 ” to 9.1/2” OD yes

Quantity 2 Ea

Tongs and Casing Equipment

Rotary Tongs with Torque Indicator

Tongs for drill pipe and drill collars -for all sizes provided (3.1/2”,

5”,5 1/2”) (4.3/4 ” to 9.1/2”)

1 set of each type

MakeBJ-Varco

Jaw sizes (in) 3-1/2"--16"

Type

HT-35,HT-100

Tong counterbalance lines, weights etc YES

Manual Casing Tongs

Quantity 1 Ea

Make BJ-Varco

Sizes (in) 7"-16"

Type HT-65

Pipe SpinnerQuantity

1

Make HWACK

Type

Size (in) 3-1/2", 5"

Iron Roughneck

Make N/A

Lifting and Handling Subs

Drill collars - for all sizes provided YES

Quantity 3 Ea F /Each size

Size 7-5/8" Reg, & 4-1/2" IF & 3-1/2" IF

Rig Specification


Bit Breakers and Rock Bit and Stabiliser Gauges yes

Sizes to fit 26”, 18.1/2”, 17.1/2", 12.1/4 ", 12”, 8.1/2 ", 6" yes

Bit breaker sizes (in) Sizes to fil 26",18-1/2",17-1/2",12-1/4", 12", 8-1/2", 6"

Bit gauge sizes - go/no-go gauges (in) Sizes to fil 26",18-1/2",17-1/2",12-1/4", 12", 8-1/2", 6"

Stabilizer gauge sizes - three point gauges (in) N/A

Mud Saver Buckets

For all drill pipe sizes provided - must be equipped with hose to

flowline and spare rubber setsyes

Pipe Wipers

For all drill pipe sizes provided. yes

Size (in) 5" &3-1/2"

Cable Cutter

Quantity1 Ea

Make model capac or equvalent

TypeHydrulic

Cable sizes (in) 2" - 1 1/4"

Air Winches

Air winch with spooling device – number 3 Ea 5 MT

Air winch make and type tai"an, china, XJFH-5/35

Air winch rated pull (lb) 5 MT

Air winch position Based on Rig Floor

Circulating Heads and Water Bushings

Number 1 Ea

Make Drillco

TypeFMC-LO Torq

Connection (top and bottom) 2" Weco Fig 1502

Rated working pressure (psi) 5000 PSI

Rig Specification


Casing scrapers

9 5/8” and 7” casing scraper yes

Quantity 1 Ea F / Each size

Make Logan or equavelant

Type 47-53.5 ppf or 9 5/8" & 26-32 ppf for 7"casing

Connection (top and bottom) 4 1/2" Reg for 9 5/8" & 3 1/2"reg for 7"

Drilling String and Associated Equipment

a full detail history and state of the drillpipe, drillcollars and subs new rig

Drillpipe Specifications

Size – 5” 5"

Grade G-105

Weight (lb/ft) 19.5 PPF

Class PEREMIUM

Range 2

Internal coating PDC

Hard banding aranco-300

Connection NC-50 , 4-1/2"IF

Length 15,000 FT

Size – 3.1/2” 3-1/2"

Grade G-105


Class PEREMIUM

Range 2


Hard banding (smooth) aranco-300

Connection NC38, 3-1/2"IF

Length 5,000 FT

Size – 2.3/8” N/A

Grade

Drillpipe Pup Joints

Size - 5" 3 Ea

Grade G-105


Class PEREMIUM

Rig Specification

Length 15 FT, 10 FT, 5 FT


Rig Specification



Connection NC-50 , 4-1/2"IF

Number 3 Ea

Size - 3 1/2" 3 Ea

Grade G-105


Class PREMIUM

Length 15 FT, 10 FT, 5 FT



Connection NC-38, 3-1/@" IF

Number 3 Ea

Size - 2 3/8" N/A

Heavyweight Drillpipe

Size - 5" HWDP (in)5"

Weight (lb/ft) 50 PPF

Range 2

Class Premium


Connection 4-1/2" IF

Number 25

Size – 3.1/2" HWDP (in) N/A

Drill Collars

Size - 9.1/2" x 3" (in) yes

Connection 7-5/8"Reg

Body type Spiral

Number 3

Short drill collar length (ft) and number N/A

Size - 8" x 2.13/16" (in) or 8 ½” x 2.13/16” yes

Connection 6-5/8" Reg

Body typeSpiral

Number 24

Short drill collar length (ft) and number N/A

Size - 6.1/2" x 2.1/4" (in) yes

Rig Specification

Connection 4-1/2" IF

Body type Spiral

Rig Specification


Number 24

Short drill collar length (ft) and numberN/A

Size - 4 3/4" x 2" (in)yes

Connection -3-1/2" IF

Body type -

Spiral

Number -24

Size – 3.1/8" x 1.1/4” (in)N/A

Connection -

Body type -

Number -

Crossover Subs

Crossover subs for each piece of TENDERER's equipment to conect between contractor equipment

Size (in) Sufficinet toconect beyween all drill string

Length (ft) as Per API Standard

Connection available to all different threads

Notes:

TENDERER shall provide all necessary subs and crossover subs

for TENDERER’s in hole and fishing equipment.

yes

Bits SubsItem

Bits Subs available for Bits size 26", 17-1/2".12-1/4", 8-3/8",amd 6'

Bit subs to be bored for Baker type floatsyes

Size (in) 9-1/2" & 8-1/4" & 6-1/2"& 4-3/4"

Length (ft)3 ft

Connection 7-5/8 reg & 6-5/8"Reg & 4-1/2" IF & 3-1/2" IF

Drillpipe / Casing Protectors

For 5” as Required

Quantity

Type

Thread Protectors

supplied downhole equipment are provided with thread protectors

fit for Yes

Recording and Indicating Equipment

Driller’s control unit

Make and model of unit Rig Sense Unit - M/D Totco

Rig Specification


Mud Shack

Quantity

Size and location relative to mud pits

Intrinsically safe electrical supply with all sockets and plugs safe

for area and

Air Conditioning unit

Water supply

Sink

120 psi air supply

Marsh Funnel Viscometer

Desk, chair and filing cabinet

Stainless Steel Work Table

Adequate number of light sockets and proper lighting plus desk

lamp

Storage space for chemicals, paperwork etc.

Mud Weight Balance

Deviation Surveying Equipment

Number 1 Set

Make and type Totco

Range 0-8 & 0-16 Degree

Baffle plate (Crows foot) to suit all drill collars Yes

Retrieving tools to recover recorder in any of the TENDERER's

tubulars Yes

Fishing Tools

Notes:

BOWEN, 7-3/4” - 8” OD and 3-1/16” ID, 6 5/8” Reg connections

C/W BOWEN

Yes

BOWEN jar, 6 1/2" OD and 2 1/4” ID, NC50 connections C/W

BOWEN jar

Yes

BOWEN , 4.3/4” OD and 1 1/2” ID, NC38 connections C/W

BOWEN jar

Yes

BOWEN series 150, type FS releasing and circulating overshot,

12 3/4” OD, to

Yes

9 1/2" OD and smaller, c/w parts for fishing with basket and spiral

grapple,18”

Yes

Fishing tools shall fit all TENDERER provided equipment and tools in all sizes for fishing in 30”, 26”, 18.1/2”, 17.1/2”, 14.1/2”,

12.1/4”, 12”, 8.1/2” Suppling fishing equipment to be maintained and inspected to same

Rig Specification


BOWEN Series 150, type FS releasing and circulating overshot,

10-5/8” OD,

Bowen Series 150, FS, 11-1/4" w/ accessories

BOWEN Series 150 type SH releasing and circulating overshot, 8

1/8" OD, to lcatch 6 5/8” OD and smaller, c/w parts for fishing with

basket and spiral grapple standard guide and 36” extension sub in

8 1/2" hole, connection

Bowen Series 150, SH, 8-1/8", w/ accessories

BOWEN Series 150 type SH releasing and circulating overshot, 5

3/4" OD, to

Bowen Series 150, SH, 5-3/4", w/ accessories

Spirals 11 1/a " and 11 1/8" and baskets 9 1/2 " and 9 3/8"

(including spirall Yes

Basket grapples and mill controls: 8", 7 7/8", 6 5/8", 6 1/2", 6 3/8",

5" forh Yes

Spirals with packers and controls: 6-3/4”, 6 5/8”, 6 1/2”, 6-3/8” and

6 1/4”;

Yes

Baskets with packers and controls: 5”, 4-3/4”, 4 5/8” 3 1/2” and 2

7/8”

Yes

All for the 8.1/8” OD overshot.

Spirals with packers and controlsYes

Baskets with packers and controlsYes

All for the 8.1/8” OD overshot.

BOWEN bumper sub, 4.3/4” OD with NC50 box x pin connections.Yes, Bowen Type

BOWEN bumper sub, 6 1/2” OD with NC50 box x pin connections. Yes, Bowen Type

Bowen bumper sub, 8" OD with 6 5/8" Reg. box x pin connectionYes, Bowen Type

Reverse circulating junk basket, 11” OD c/w mill type shoe and

catcher.Yes

Reverse circulating junk basket, 7-7/8” OD c/w mill type shoe,

catcher and

Yes

Reverse circulating junk basket, 5-3/4” OD c/w mill type shoe and

catcher

Yes

Magnet, 11” OD, with 6 5/8” Reg pin connection. N/A

Magnet, 8” OD, with 4 1/2” Reg pin connection. N/A

Junk sub, 12-7/8” OD cup, 7 5/8” Reg box x pin connection.Yes

Junk sub, 9 5/8” OD cup, 6 5/8” Reg box x pin connection. Yes

Junk sub, 6 5/8” OD cup, 4 1/2” Reg box x pin connection.Yes

Junk sub, 5” OD cup, 3 1/2” Reg box x pin connection. Yes

Rotary tap to catch 6 5/8” Reg tool joint, 7-3/4” OD body, wicker

range 3”-4-N/A

3/4”

Rotary tap to catch NC50 tool joint, 6-1/8” OD body, wicker range

3 1/4” – 4-

N/A

3/4”

Rotary tap to catch NC38 tool joints, 6” OD body, wicker range 2-

7/8” - 4”

N/A

1/2”

Lead impression block, 8” OD body with NC50 pin connection. N/A

Impression block, 5 3/8 OD body with NC38 box connection. N/A

Mud ditch magnets N/A

Junk mills, flat bottom type for hole size 17 1/2”, 12 1/4” , 8 1/2”

and 6".

Yes

Rig Specification


Casing releasing spear, 8 1/4” OD, with grapples to catch casing

sizes 18N/A

Casing releasing spear, 5-3/4” OD, with grapple to catch casing

size 7”N/A

Safety joints with NC46 and 6 5/8" Reg connections. N/A

Auxiliary Equipment for the Rig

Cutting and Welding Equipment

Welding set, 400 Amperes with 100 m of cable. Yes Lincoln Type

Oxy-Acetylene cutting gear Yes

Accessories e.g. shields, goggles, fireproof gloves Yes

Air CompressorsQuantity 2 Ea

Make and TypeSullair, LS12-50HHAC

Power supply Electric Power Supply

Discharge pressure (psi) 150 PSI

Air receiver volume (cuft/min) 800 cfm

Deliverability, volume and pressure (cuft/min and psi) 40 PSI

Locationbeside prime mover supply

Slickline (Wireline) Unit

Make and Type Tai"an, Mathy type

Measuring device units Meter

Capacity and line OD (in) 4500 Meter, OD = 0.098"(2.5mm)

Communication EquipmentPortable VHF radios, intrinsically safe Yes

Rig intercom unitYes, 8 Units

Communications system between driller's console and monkey

boardYes

Satellite communication system with Voice and fax capability. N/A

Computer equipmentYes, F / Toolpusher, Radio Operator, Safety Engineer,

Material Man

Rig Specification


Cleaning Units

Item

Water blast (HP) unit 1 ea high pressure cleaner, Niagra Type, 200 gpm

Vehicles

Fork lift - number and type 1 ea Rental, as Required

Fork lift - capacity (mt) Capacity 5 mt

Crane - number and type 1 ea Rental, as Required

Crane - capacity Capacity 50 mt

Chiksan Lines

Type Fig1502

Size 2"

Number 40 Ft

Pipe Racks (and Pipe Baskets)

Quantity Sufficient for all rig operations

Capacity Sufficient for all rig operations

Air Blowers

Quantity N/a

Rig Lighting

Rig lighting system Yes, Sufficient for all rig operations

Other Equipment

Chain tongsYes

Pneumatic wrench and sockets for making bolts on API flanged

connections on BOP stacks and wellhead flanges.

Yes

Inside and outside callipersYes

Key-hole plate (C plate), 1.1/2" steel (false rotary) for cementing

surface casing using the inner string method

Yes

Photocopier in TENDERER's office Yes

All hoses required to supply fuel and water to the rig and camp Yes

Fuel gauges for metering receipt of diesel fuel. Yes

Fuel oil transfer pumps and fuel filter water separator

Set of slings each for drill collar, drill pipe, casing and tubing

handling.Yes

Rig Specification


Set of six (6) sinker bars of 1 5/8” OD with swivel connection to

wireline

Yes

Sets of 2” ID, long sweep HP cementing and circulating steel

hoses, FMC or equivalent, 5,000 psi WP Yes

Flare line, 5” from choke manifold to flare pit Yes

Portable pump for dead volume transfer with flexible hose Yes

Safety Equipment

Safety EquipmentDescription 1

Description 2

Personal Protective EquipmentRequired minimum items to be worn by TENDERER personnel

are:

sufficient for full complement of Contractor’s personnel

Safety helmet (non-metallic) c/w chin straps Yes, Hard Helmet non metallic w/strap

Work clothes (suit or overalls) Overalls

Safety boots Yes, Oil Resistance

Protective gloves Yes, Cotton gloves

Ear protection for use in areas of high noise Yes

Safety glasses Yes

Breathing Equipment

sufficient to implement contractor H2S & Gas plans and

comply with any regulatory authority requirements.

Self contained breathing apparatus (30 minute cylinder) with

spare cylinders for 2 hours supply located as follows: 4 complete sets + 2 spare cylinders

Drill floor Yes

COMPANY and TENDERER offices Yes

Total number of 30 minutes breathing apparatus sets 4 complete sets + 2 spare cylinders

Recharging system for B.A. cylinders - type and capacity

(bottles/hour)Yes, available in Base

10 minutes BA Escape Set 4 Each - Above On Company Cost

Fire Fighting Equipment - Immediate Action

COMPANY minimum requirements are:sufficient to implement contractor fire fighting plans and

comply with any,regulatory authority requirements.

50 kg dry powder extinguisher located at fuel oil storage area 1 Ea

5 kg CO2 extinguisher located at the Generators 1 Ea x 10 KG

5 kg CO2 extinguisher located at Electrical switchboard 1 Ea x 10 KG

12 kg dry powder extinguisher located at Dog house 1 EA

Rig Specification


12 kg dry powder extinguisher located at the mud pits2 Ea

12 kg dry powder extinguisher located at the BOP accumulator 1 Ea x 10 KG

12 kg dry powder extinguisher per room in change rooms, office,

store room etc

2 Ea x 9 KG On Each Master Skid

Mobile units for site and camp - 50 kg dry powder extinguishers

on ±3 ft diameter metal wheels

1 Ea at Main Camp

Fire Fighting Equipment - Further Action

Fire water tank of not less than 200 bbl, with 4" lines and sufficient

hoses and branch pipework to reach any part of the site

Yes

Diesel driven fire pump complete with adequate hoses -type and

output (bbl/min)

Yes

Foam generator unit, with an output rate not less than 12 bbl/min

foam - type and output (bbl/min)

yes- Connected to Fire Tank

Personal Protection for Fire Fighting Personnel

Helmet with face shield

2 Ea

Fire suits

2 Ea

Fire blankets

5 Ea

Fireproof gloves

2 Ea

Gas Detection and Alarm System

Permanent Installation Requirement

Description

Portable InstrumentsElectronic combustible gas detectors, intrinsically safe - type and

range (ppm

1 Ea on dog house

Electronic toxic gas meters for H2S, SO2 and CO2, intrinsically

safe - type and range (ppm)

2 Ea (dog house & Mud System)

Alarm System

A general alarm system, installed which is operated via a

manual alarm switch at the driller's console on the drillfloor as

well as from the toolpushers office. This should activate a

Battery Powered Loudspeaker (Loud Hailer)

Loud hailers should be provided, one at the drilling location and

one at the campsite2 Ea Mobile Land Speaker

Rig Specification


First Aid Supply

First aid supply - provide detailed list of contents of first aid

supply.

Yes

Folding rescue stretchers Yes

Portable Mars resuscitator Yes

Oxygen masks Yes

Safety Equipmentas required

Derrick man escape line (Geronimo line)Yes, 1 Ea

Distance of landing position from derrick 50 - 60 Meter

Safety belts and harnesses Yes

Derrick man safety line (sky-hook) with counter balance N/A

Derrick man safety equipment - Safety belt, belly buster and Sella

block type anti-fall device

Yes

Inertia reel installed above stabbing board - for connection to

stabber safety belt

Yes

Eye wash stations positioned in proximity of mud active tanks,

drill floor, mixing hoppers, shale shakers and monkey board

Yes, Except Monkey Board

Portable shower in mud mixing area Yes

Additional Equipment in the Rig Safety Store

Camp Equipment

General description and details of further Porta-cabin

accommodation / cabin facilities to accommodate +/8 people at at

Mini Camp (Rig Site Camp),

Mini Camp Capacity + 8 People, Provide w/Facilities,Air

Conditions, Lights, Beds with Accessories internal Bath

room between Cabines W/ Exhaust Fan, Showers hot /

Cold, secure Lockers, TV and fridge, Pot Water Tank,

General description and details of further accommodation / cabin

facilities to accumiddate +/80 people at Main Camp far away of

drilling site with minimum distance of 500 mt

Yes, Capacity of Main Camp + 80 People Caravans

Provide with all Facilities, Air Conditions, Lights, Beds

with Accessories internal Bath room between Cabines W/

Exhaust Fan, Showers Hot / Cold, secure Lockers,

Refridgeration unit for food storage,Recreati

Radio shackYes

Security Gate house Yes

Mud sack storage storehouse - size and sack capacity N/A

Warehouse - size and capacity 3 Ea, Dimensions = 12.20 meter x 2.70 meter x 2.60 meter

Workshop - size and equipment provided3 Ea, 1 Ea F/Mechnic & 1 Ea F/Electrican Dimensions = 10.03

m x 2.90 m x 3.05 m, 1 Ea F/ Welder, Dimension = 6.10m x

2.45 m x 2.60 m

Spare PartsSpare parts are available to adequately cover contingencies and

maintain full operational capability at all times

Yes, as per Stock Control System

Rig Specification

Name ZJ50D(S102) Make Kerui, China Type - ADSO · Drawworks Power (hp) 1500 HP powered by 2 x750 hp...

Documents

Transcript of Name ZJ50D(S102) Make Kerui, China Type - ADSO · Drawworks Power (hp) 1500 HP powered by 2 x750 hp...