Name Of Faculty : Mr. Pradeep Kuhar ( Theory )

Discipline : CIVIL

Semester : 6th

Subject : DCS-II

Lesson Plan Duration: 15 Weeks( from January 2018 to April 2018)

Work Load (Lecture/Practical) per week (in Hours ) :Lectures 04

Theory

Week Lecture day Topic

1st 1st Continuous Beams-Basic assumptions

2nd Moment of inertia,settlements, Modification of moments

3rd Moment of inertia, settlements, Modification of moments,

4th Moment of inertia, settlements,Modification of moments

2nd 1st Maximum moments and shear, beams curved in plan-analysis for torsion

2nd Maximum moments and shear, beams curved in plan-analysis for torsion

3rd Maximum moments and shear, beams curved in plan-analysis for torsion

4th Redistribution of moments for single andmulti-span beams

3rd

1st Redistribution of moments for single and multi-span beams

2nd Design examples

3rd Design examples

4th Flat slabs and staircases-Advantages of flat slabs, general design considerations

4th

1st Flat slabs and staircases-Advantages of flat slabs, general design considerations

2nd Approximate direct design method, design of flat slabs, openings in flat slab

3rd Approximate direct design method, design of flat slabs, openings in flat slab

4th Approximate direct design method, design of flat slabs, openings in flat slab

5th 1st Design of various types of staircases

2nd Design examples

3rd Design examples

4th Foundations-Combined footings, raft foundation

5th

6th 1st Foundations-Combined footings, raft foundation

2nd Design of pile cap and piles, underreamed piles

3rd Design of pile cap and piles, underreamed piles

4th Design examples

7th 1st Design examples

2nd Water Tanks, Silos and Bunkers-Estimation of Wind and earthquake forces, design requirements

3rd Water Tanks, Silos and Bunkers-Estimation of Wind and earthquake forces, design requirements

4th Water Tanks, Silos and Bunkers-Estimation of Wind and earthquake forces, design

requirements

8th 1st Rectangular and cylindrical underground and overhead tanks, Intze tanks, design considerations

2nd Rectangular and cylindrical underground and overhead tanks, Intze tanks, design considerations

3rd Rectangular and cylindrical underground and overhead tanks, Intze tanks, design considerations

4th Design examples

9th 1st Design examples

2nd Silos and Bunkers-Various theories

3rd Bunkers with sloping bottoms and with high sidewalls

4th Design examples

10th 1st Design examples

2nd Prestressed Concrete-Basic principles, classification of pre-stressed members

3rd Prestressed Concrete-Basic principles, classification of pre-stressed members

4th Various prestressing systems

11th 1st Losses in pre-stress, initial and final stress conditions,

2nd Analysis and design of sections for flexure and shear, load balancing concept

3rd IS Specifications

4th End blocks-An lysis of stresses

12th 1st Magnel's method, Guyon's method, Bursting and spalling

stresses

2nd Design examples

3rd Building Frames-Introduction

4th Member stiffnesses, Loads, Analysis for vertical and lateral loads

13th 1st Torsion in buildings, Ductibility of beams

2nd Design and detailing for ductility

3rd Design examples

4th Design examples

14th 1st Yield Line Theory-Basic assumptions, Methods of analysis, yield line patterns and failure mechanisms

2nd Yield Line Theory-Basic assumptions, Methods of analysis, yield line patterns and failure mechanisms

3rd Analysis of one way and two way rectangular and non-rectangular slabs

4th Analysis of one way and two way rectangular and non-rectangular slabs

15th 1st Effect of top corner steel in square slabs

2nd Effect of top corner steel in square slabs

3rd Design examples

4th Design examples

Name Of Faculty : Mr. Sandeep ( Theory )

Discipline : CIVIL

Semester : 6th

Subject : Geology

Lesson Plan Duration: 15 Weeks( from January 2018 to April 2018)

Work Load (Lecture/Practical) per week (in Hours ) :Lectures 04

Theory

Week Lecture day Topic Practical day Topic

1st 1st Definition, object, scope.

Day 1 Study of Physical properties of minerals.

2nd sub division of geology, geology around us.

3rd The interior of the earth. Importance of geology in Civil Engineering projects.

4th The external and internal geological forces causing changes,

2nd 1st weathering and erosion of the surface of the earth.

Day 2 Identfication of rocks forming silicate and ore minerals.

2nd Geological work of ice, water and winds.

3rd Soil profile and its importance

4th

Earthquakes and volcanoes.

3rd 1st Definition and mineral and rocks

Day 2

Recognition of rocks.

2nd Classification of important rock forming minerals

3rd Classification of important rock forming minerals

4th simple description based on physical properties of minerals.

4th 1st simple description based on physical properties of minerals.

Day 3 Files checking.

2nd

Rocks of earth surface, classification of rocks.

3rd

Mineral composition, Textures, structure.

4th

origin of Igneous, Sedimentary and Metamorphic rocks.

5th 1st Aims and principles of stratigraphy.

Day 4 Use of clinometers compass and Bruton compass for measurement dip and strike of formations.

2nd Standard geological/

stratigraphical time scale with its sub division and a short description based on engineering uses of formation of India.

3rd Standard geological/ stratigraphical time scale with its sub division and a short description based on engineering uses of formation of India.

4th Forms and structures of rocks.

6th 1st Bedding plane and outcrops,

Day 5 Geological cross sections and study of geological maps.

2nd Dip and Strike. Elementary ideas about fold, fault, joint and unconformity and recognition on outcrops.

3rd Dip and Strike. Elementary ideas about fold, fault, joint and unconformity and recognition on outcrops

4th Importance of geological structures in Civil Engineering projects.

7th 1st Hydrogeology, aquifers,water table

Day 6 Files checking.

2nd springs and Artesian well

3rd aquifers, ground water in engineering projects.

4th Artificial recharge of ground water,

8th 1st Elementary ideas of geological investigations.

Day 7 Study of models of geological structures and out crops patterns of different types of rocks and land forms.

2nd Remote sensing techniques for geological and hydrological survey and investigation.

3rd Uses of geological maps

4th interpretation of data, geological reports.

9th 1st Interpretation of data, geological reports.

Day 8 Files checking

2nd Artificial recharge of ground water

3rd Hydrogeology, aquifers,water table

4th Physio graphic division in India,

10th 1st simple description based on physical properties of minerals.

Day 9 viva

2nd Suitability of foundation sites

3rd Stability of foundation

sites.

4th Stability abutments.

11th 1st Suitability of abutments.

2nd Geological conditions

Day 10 Revision first

experiment.

3rd Geological conditions and their influence on the selection, location of dams.

4th Types of dams,

12th 1st Types of dams,

Day 11 Revision of

second

experiment.

2nd Design of dams

3rd Design of dams

4th Design of dams

13th 1st Design of dams

2nd Types of reservoirs

Day 12 Files checking.

3rd Types of reservoirs

4th Design of reservoirs

14th 1st Types of tunnels Day 13 viva

2nd Types of tunnels

3rd Types and design of highways,

4th Types and design of highways

15th 1st Types and design of

bridges.

Day 14 Files checking.

2nd Types and design of

bridges.

3rd Class Test-3

4th Assignment checking.

1st Definition, object, scope.

Name Of Faculty : Mr. Sudhir ( Theory )

Discipline : CIVIL

Semester : 6th

Subject : Geotechnology

Lesson Plan Duration: 15 Weeks( from January 2018 to April 2018)

Work Load (Lecture/Practical) per week (in Hours ) :Lectures 03

Theory

Week Lecture day Topic Practical day Topic

1st 1st Stability of slopes Day 1 Grain Size Analysis-Hydrometer method

2nd Causes of failure, factors of safety

3rd slopes types of failures of finite slopes

2nd 1st analysis of finite slopes-mass procedure, method of slices, effect of pore pressure

Day 2 Shrinkage- Limit Determination

2nd Fellinius method to locate centre of most critical slip circle, friction circle method, Tayler's stability number

3rd slope stability of earth dam during steady seepage

3rd

1st Braced Cuts Day 3 Relative Density of Granular Soils

2nd Depth of unsupported vertical cut

3rd sheeting and bracing for deep excavation,

4th

1st movements associated with sheeting, and bracing

Day 4 Consolidated Drained (CD) Triaxial Test

2nd modes of failure of braced cuts

3rd pressure distribution behind sheeting

5th 1st Cofferdams Day 5 Consolidated Undrained (CU) Triaxial Test with Pore Water Pressure Measurement

2nd Introduction, types of cofferdams

3rd design and lateral stability of braced cofferdams

6th 1st design and lateral stability of braced cofferdams

Day 6 Consolidation Test

2nd design and lateral stability of braced cofferdams

3rd design and lateral stability of braced cofferdams

7th 1st design data for Cellular cofferdams

Day 7 Consolidation Test

2nd stability analysis of cellular cofferdams on soil and rock

3rd stability analysis of cellular cofferdams on soil and rock

8th 1st inter-lock stresses

Day 8 Standard Penetration Test

2nd inter-lock stresses

3rd Cantilever Sheet Piles

9th 1st Purpose of sheet piles Day 9 Dynamic Cone Penetration Test

2nd cantilever sheet piles

3rd depth of embedment in

granular soils-rigorous method Simplified procedure

10th 1st depth of embedment in granular soils-rigorous method Simplified procedure

Day 10 Models Plate-Load Test

2nd depth of embedment in granular soils-rigorous method Simplified procedure

3rd cantilever sheet pile

11th 1st Penetrating clay

2nd limiting height of wall

3rd limiting height of wall

12th 1st Anchored Bulkheads Methods of design, free earth support method in cohesionless

2nd free earth support method in cohesive soils

3rd fixed earth support method in cohesionless soils-Slum's equivalent beam method

13th 1st fixed earth support method in cohesionless soils-Slum's equivalent beam method

2nd Soil Stabilization

3rd Soil improvement, shallow compaction, mechanical treatment, use of admixtures

14th 1st lime stabilization cement stabilization, lime fly ash stabilization

2nd dynamic compaction and consolidation, Bituminous stabilization, chemical stabilization, pre-

compression

3rd lime pile and column, stone column, grouting reinforced earth

15th 1st Basics of Machine Foundations Terminology, characteristics elements of a vibratory systems, analysis of vibratory motions of a single decree freedom system-undamped free vibrations

2nd undamped forced vibrations, criteria for satisfactory action of a machine foundation, degrees of a freedom of a block foundation, Barken’s soil spring constant

3rd Barken's method of a determining natural frequency of a block foundation subjected to vertical oscillations

Name Of Faculty : Mr. Sunil ( Theory )

Discipline : CIVIL

Semester : 6th

Subject : IE-I

Lesson Plan Duration: 15 Weeks( from January 2018 to April 2018)

Work Load (Lecture/Practical) per week (in Hours ) :Lectures 04

Theory

Week Lecture day Topic

1st 1st Regulation works: Canal lulls-necessity and location

2nd Development of falls, design of cistern clement

3rd Roughening devices, Principal of design of Sarda type fall

4th Design of straight Glacis fall

2nd 1st Off-take alignment, cross-regulator and distributor}' head regulators

2nd Devices to control silt entry into the off-taking channel

3rd Silt ejector, canal escapes, types of escapes

4th Cross drainage works: Classification and their selection

3rd

1st Fondamentals of hydraulic design aspects of aqueducts

2nd Fondamentals of hydraulic design aspects of aqueducts

3rd Syphon aqueducts, super passage

4th Syphon aqueducts, super passage

4th

1st Canal syphon and level crossing

2nd Design of transitions

3rd Design of transitions

4th Bligh's creep theory

5th 1st Khosla's method of independent variables

2nd Use of Khosla's curves, various corrections

3rd Silt excluders

4th Storage Headworks: Types of dams, selection of a site

5th Gravity dam-two dimensional design

6th 1st Forces acting, stability criterion

2nd Forces acting, stability criterion

3rd Elementary profile of a dam

4th Elementary profile of a dam

7th 1st Cutoffs and drainage galleries

2nd Arch dams-constant angle and constant radius arch dam

3rd Arch dams-constant angle and constant radius arch dam

4th Simple design and sketches

8th 1st Most economical angle

2nd Earth dam

3rd Earth dam

4th Design principles, seepage through earth dams

9th 1st Design principles, seepage through earth dams

2nd Seepage line, control of seepage

3rd Design of filters

4th Spillways and Energy Dissipations: Essent ial

requirements of spillway

10th 1st Spillways and Energy Dissipations: Essent ial requirements of spillway

2nd Spillway's capacity

3rd Types of spillways and their suitability

4th Ogee spillways

11th 1st Chute, side channel, shaft and syphon spillways

2nd Chute, side channel, shaft and syphon spillways

3rd Energy dissipation below spillways

4th Stilling basins

12th 1st USBR and I..S.

2nd USBR and I..S.

3rd Stilling Basins

4th Stilling Basins

Name Of Faculty : Mr. Naveen ( Theory )

Discipline : CIVIL

Semester : 6th

Subject SEWAGE AND TREATMENT

Lesson Plan Duration: 15 Weeks( from January 2018 to April 2018)

Work Load (Lecture/Practical) per week (in Hours ) :Lectures 04

Theory

Week Lecture day Topic Practical day Topic

1st 1st Importance of sanitation,

Day 1 Based on course work corresponding to Environmental Engineering

2nd Systems of sewerage - separate

3rd combined and partially separate. Quantity of sanitary sewage and variations

4th Shapes of sewer- circular and egg shaped

2nd 1st Design of sewers, self cleansing Velocity and slopes, Construction and testing of sewer lines

Day 2 Sampling and analysis of water test like hardness, chloride, sulphate phosphate, D.O, PH, connectivity

2nd Sewer materials, joints and appurtenances.

3rd Sewage collection from houses and buildings,

4th

general principal for design of a sanitary plumbing system

3rd 1st Traps function and types

Day 2

File checking

2nd System of plumbing, testing of house sewer

3rd sanitary fittings and other accessories

4th ventilation of house drainage

4th 1st waste water recycling in building

Day 3 Sampling and analysis of waste water Like D.O ,B.O.D ,C.O.D, Suspended solid

2nd

Quality parameters- BOD, COD

3rd

Solids, D.O., Oil & Grease, tests

4th

Sewage disposal

5th 1st Class test

Day 4 Measurement of noise level

2nd type relative advantage and disadvantage of various sewage disposal system Indian

3rd Standards for disposal effluents into inland

surface sources and on land

4th Bangalore method and Indore method of sewage disposal

6th 1st Disposal of sewage by dilution - self-purification of streams

Day 5 Total suspended particulate matters

2nd Sewage disposal by irrigation

3rd Digestion and disposal of primary and secondary sludge

4th Moisture content

7th 1st sludge digestion process

Day 6

2nd Factors affecting

File checking

3rd Objectives of sewage Treatment, classification of treatment process

4th Preliminary treatment -screening and grit removal units

8th 1st Skimming tanks,

Day 7

2nd Theory and design aspects of sedimentation

Sulphation rate in water samples

3rd coagulation, merit and demerits of coagulation

4th Class test

9th 1st Secondary treatment- Biological Filtration

Day 8

2nd Trickling Filter, High rate Trickling Filter advantage and disadvantages

Fluoride measurement in water samples

3rd miscellaneous type of filter, Humus tank, activated sludge process

4th aeration tanks, secondary sedimentation tanks

10th 1st Stabilization pond

Day 9

2nd oxidation pond, Oxidation ditches

File checking

3rd aeration lagoons

4th anaerobic stabilization units

11th 1st septic tank and Inhoff tank

2nd Sludge Digestion UASB process sequence and efficiencies of conventional treatment units

Day 10 viva

3rd Sludge Digestion UASB process sequence and efficiencies of conventional treatment units

4th Sludge Digestion UASB process sequence and efficiencies of conventional treatment units

12th 1st Process Design of a complete sewage treatment plant, Examples

Day 11 High volume and handy sampler s

2nd Examples

3rd Examples

4th Examples

13th 1st Noise Pollution- Definition and introduction

File checking

2nd Effect of Noise, characteristics of sound and it’s measurement

Day 12

3rd level of noise , noise rating system and standards

4th source of noise their levels and controls

14th 1st Air pollution –Definition of air pollution

Day 13

2nd Effects of air pollution, Dispersion of air pollution in atmosphere

Viva

3rd Effects of air pollution, Dispersion of air pollution in atmosphere

4th Effects of air pollution, Dispersion of air pollution in atmosphere

15th 1st Dispersion Day 14 Viva

models and equations

2nd Dispersion models and equations

3rd Air pollution controls.

4th Class test 3

Name Of Faculty : Mr. Sanjay ( Theory )

Discipline : CIVIL

Semester : 6th

Subject : TE-II

Lesson Plan Duration: 15 Weeks( from January 2018 to April 2018)

Work Load (Lecture/Practical) per week (in Hours ) :Lectures 03

Theory

Week Lecture day Topic Practical day Topic

1st 1st Types of pavements. Flexible and rigid pavements

Day 1 Aggregate Impact Test

2nd Components of a pavement and their functions

3rd Factors affecting design of pavements

4th Design of thickness of a flexible pavement by Group Index method

2nd 1st CBR method (including latest IRC guidelines)

Day 2 Los-Angeles Abrasion Test on Aggregates

2nd Triaxial method and Burmister’s method

3rd Triaxial method and Burmister’s method

4th Examples

3rd

1st Westergaard’s theory Day 3 Dorry's Abrasion Test on Aggregates

2nd Westergaard’s theory

3rd Critical locations of loading

4th Load and temperature stresses

4th

1st Load and temperature stresses

Day 4 Deval Attrition Test on Aggregates

2nd Critical combination of

stresses.

3rd Critical combination of stresses.

4th IRC guidelines for determination of thickness of a rigid pavement

5th 1st IRC guidelines for determination of thickness of a rigid pavement

Day 5 Crushing Strength Test on Aggregates

2nd Joints: requirements, types, patterns

3rd Spacing of expansion and contraction joints

4th Functions of dowel and tie bars

6th 1st Functions of dowel and tie bars

Day 6 Penetration Test on Bitumen

2nd Brief introduction to earthwork machinery: shovel

3rd Hoe, clamshell,

7th 1st Dragline, bulldozers Day 7 Ductility Test on Bitumen

2nd Principles of field compaction of subgrade

3rd Compacting equipments

8th 1st Compacting equipments

Day 8 Viscosity Test on Bituminous Material

2nd Granular roads. Construction steps of WBM. WMM. Construction of cement concrete pavements

3rd Slip-form pavers, Basic concepts of the following: soil stabilized roads

4th Use of geo-synthetics, reinforced cement concrete pavements, prestress concrete pavements

9th 1st Roller compacted concrete pavements and fibre reinforced concrete pavements

Day 9 Softening Point Test on Bitumen

2nd roller compacted concrete pavements and fibre reinforced concrete pavements

3rd Various types of bituminous constructions. Prime coat

4th Tack coat, seal coat

10th 1st Surface dressing. Construction of BUSG

Day 10 Flash and Fire Point Test on Bitumen

2nd Premix carpet

3rd BM, DBM and AC

4th BM, DBM and AC

11th 1st Brief coverage of machinery for construction of bituminous roads: bitumen boiler, sprayer, pressure distributor

2nd Brief coverage of machinery for construction of bituminous roads: bitumen boiler, sprayer, pressure distributor

3rd Hot-mix plant, coldmix plant

12th 1st Tipper trucks, mechanical paver or finisher, rollers. Mastic asphalt. Introduction to various IRC and MOST specifications.

2nd Pavement failures. Maintenance operations. Maintenance of WBM, bituminous surfaces

and cement concrete pavements. Pavement evaluation

3rd Pavement failures. Maintenance operations. Maintenance of WBM, bituminous surfaces and cement concrete pavements. Pavement evaluation

4th Benkleman beam. Introduction to various types of overlays

13th 1st Surface drainage: types, brief design. Types of sub-surface drainage

2nd Surface drainage: types, brief design. Types of sub-surface drainage

3rd Special characteristics of hill Roads: geometrics, hair pin bends, construction of hill roads

4th Special characteristics of hill Roads: geometrics, hair pin bends, construction of hill roads

14th 1st Drainage of hill roads, maintenance problems of hill roads

2nd Need of economic evaluation. Highway user benefits and costs

3rd Methods of economic evaluation:

benefit cost ratio method, net present value method

4th Methods of economic evaluation: benefit cost ratio method, net present value method

15th 1st Internal rate of return method, comparison. Highway finance

2nd Internal rate of return method, comparison. Highway finance

3rd Sections of tunnels: advantages, limitations and suitability of each section

4th Sections of tunnels: advantages, limitations and suitability of each section

16th 1st Shaft. Pilot tunnel

2nd Driving tunnel in rocks: sequence of construction operations, full-face method, heading and bench method, drift method

3rd Driving tunnels in soft ground: sequence of construction operations, needle beam method

4th shield tunneling, compressed air tunneling