Nagarajan Sridhar Power electronics in · PDF fileand the advances in power electronics to...
Transcript of Nagarajan Sridhar Power electronics in · PDF fileand the advances in power electronics to...
Power electronics in automotive applications
Introduction
Over the last few decades, electrical loads in an auto-motive system have evolved from lighting and battery-charging towards infotainment, sensors and safety, thanks to component miniaturization. This has made the car smarter and more fun to drive! While the trend of electronics in infotainment systems continues, a future trend is electronics in power train systems for better engine propulsion, like the engine blocks, transmission and controls. Incorporating electrical loads and replacing the conventional mechanical and hydraulic loads in the power train improves efficiency. This trend is seen with more and more focus on electric vehicle concepts – hybrid (HEV) and pure (EV). This trend is also expected to lower C02 emission standard requirements. This increasing need and demand makes the conventional 12V power system more challenging [1], [2]. As such, it is critical to have higher voltages in order to handle power train loads more efficiently – and with flexibility. Switched-mode power supplies (SMPS) provide the basis to do so. This is made possible due to advances in power electronics. In other words, having different power-conditioning systems between the bat-tery and loads is a way to accomplish this. Additionally, higher fuel efficiency standards have been mandated in several countries across the globe. To be clear, fuel efficiency is measured in terms of miles per gallon (MPG) for fuel injection vehicles, and miles per charge for electric and hybrid electric vehicles. Implementation of power electronic circuits makes the system smaller and lighter and, therefore, provides the basis to improve the fuel efficiency as well. Power electronics systems exclusively use silicon-based power management with power semiconductor switches. These switches are power metal-semicon-ductor field-effect transistors (MOSFETs), insulated gate bipolar transistors (IGBTs), and a variety of diodes that have made significant improvements in their performances. This paper presents a review of power electron-ics systems in electric vehicles with emphasis on the power train system. The paper also addresses the high temperature requirements in the power train system and the advances in power electronics to handle them.
Nagarajan SridharProduct Marketing Manager,
High-Performance Isolated Power Solutions, Power Management
Texas Instruments
W H I T E P A P E R
Higher voltage systemsAs mentioned earlier, systems operated by a 12V battery is becoming more challenging. You might
ask, what is the higher voltage of choice compatible with the 12V battery and electrical loads,
primarily in the power train system? It turns out that new architectures are based on a 48V system
for internal combustion engines (ICE) and HEV systems, whereas an additional 400V-200V system
is used in EVs.
Incorporating high voltages makes system wiring less complex and lighter. This has a direct
impact on lowering the vehicle’s overall weight, in addition to overcoming other disadvantages
in the 12V system [3]. Examples of loads that can be driven from the 48V system are generator/
starter, electric power steering, electric roll stabilization, electric AC compressor, electric heating,
and electric pumps (water, oil, and vacuum).
The SMPS conceptSwitched-mode power supply (SMPS) is based on semiconductor devices that operate in ON and
OFF states. Operating in these states, in theory, implies no power loss at either of these states
(zero current during off state and zero voltage during off state). Theoretically, this implies 100%
efficiency. The switches are turned on or off using a technique known as pulse-width modulation
(PWM). Also, these switches can operate under high switching frequencies, making the power con-
verters less bulky and smaller in size. Based on this information, three types of power conditioners
can be realized in automotive power train systems: AC/DC (rectifier); DC/DC (converter); and AC/DC
(inverter).
SMPS applications in the power train systemElectric vehicles, HEVs and ICE primarily need the following SMPS conditioners in their power train
systems:
• Regenerative braking (AC/DC)
• Onboard charger (AC/DC)
• Dual-battery system (DC/DC)
o Battery management for Lithium-Ion (Li-Ion) batteries
o 48V-12V bi-directional power supply
• 400V Battery (for pure EV only)
o Bi-directional 400V-12V power supply (DC/DC)
o Traction motor (DC/AC)
DC/DC convertersSeveral basic topologies are available for these power-conditioning systems based on the electrical
load safety requirements – classified as isolated and non-isolated topologies [4]. In general, both
types of topologies are adopted in power train systems. This depends on the loads and standards
requirements. Regardless of type, market adoption is trending towards a soft-switching concept
using an LLC or resonant mode. Soft switching means that the switches are subjected to lower
stress, which implies a longer life and higher reliability of these converters, very vital for automotive
markets.
There is a bi-directional power supply converter for both EVs and HEV/ICE, namely 400V-12V and 48V-12V,
respectively. Figure 1 shows the 48V-12V network with different associated loads. Normal operation of these
converters is in the buck mode. For instance, the power flows from the higher battery voltage to the lower
voltage (12V). An example of this is regenerative braking and during warm cranking. On the other hand, power
flow takes place in the boost mode (12V to higher voltage) during a cold crank or a cold-start mode. This occurs
when backup power is required during a situation where the 48V or 400V (Li-Ion) battery fails to drive the motor.
Based on power levels that vary from 1 to 3kW, full-bridge topology is a good choice when isolation is
required with a buck-boost topology for non-isolated cases. These converters are based on power MOSFET
switches that switch at very high frequencies (typically 50-500 kHz).
Figure 1. A 48V-12V bi-directional power supply and electrical loads.
Traction inverter (DC/AC)To convert electrical to mechanical energy in order to run the vehicle, motors are required. Previously, DC motors
were implemented for their simplicity and ease of control. However, DC motors are unreliable and show lower
efficiency compared to AC motors. Over the last couple of decades, tremendous progress has been made in
building controllers for AC motors. Moreover, AC motors are physically smaller with fewer parts that significantly
improve its reliability.
Therefore, the power stored in the battery (EV, HEV or ICE) must be converted from DC to AC in order to run
AC motors. These inverters, called traction inverters, usually transfer power in the tens of kW range. Hence, the
switches used in these topologies (full bridge) are IGBTs (individual or intelligent power modules, depending on
the current requirement).
Power electronic componentsRegardless of power conditioning system type (DC/DC, AC/DC or DC/AC), all require controllers and gate drivers.
Currently, the choice of analog or digital controllers is highly dependent on the vehicle or power supply manu-
facturer’s requirements. This includes cost, flexibility, integration, reliability and availability to write firmware (for
digital controllers). Likewise, the choice of gate drivers is dependent on the drive current that in turn is dependent
on several factors. This includes the semiconductor switch it needs to operate, reduced component count (single
channel versus bridge drivers), features such as dead-time control, and adaptive delay to avoid shoot-through
between high-side and low-side switches and isolation, to name a few. Texas Instruments has several automotive
grade analog and digital controllers and gate drivers to turn the power electronic switches on and off.
Power electronics in automotive applications November 2013
2 Texas Instruments
12V 48V
GNDGND
12VLoad
12VLoad
12VStarter/
(Cold Crank)
12VBattery
12V/48VDC/DC
Converter
48VBattery
48VStarter/
Generator48V
Load48V
Load
Power electronics in automotive applications November 2013
3Texas Instruments
High temperature requirementAnyone opening the hood of a car can feel heat radiating, especially after the car has been driven for a while. This
is because the power train system with the engine as one of the sub-systems (internal combustion or motor) oper-
ates at temperatures exceeding 125 degrees Celsius (Figure 2).
Figure 2. Engine block under high temperature conditions
We discussed the value of power electronic systems that transfers power very efficiently and occupies much
less space. This makes the car lighter, and improves vehicle reliability due to lack of moving parts.
As space or size comes down, power density gets higher. This is true especially for higher power transfer in the
kW range, typical of power train systems. The problem, however, is heat dissipation. Therefore, in addition to reduc-
ing the overall size, managing the thermal issues is another key factor towards improving fuel efficiency. Using
commercially available power electronic switches, such as silicon-based MOSFETs and IGBTs, there are limitations
to overcome.
For example, silicon-based power switches suffer from reverse recovery and breakdown issues at higher
temperatures (Table 1). If using silicon-based switches for the power electronic circuits subjected to high tem-
peratures, cooling systems such as large copper blocks with water jackets need to be added. However, this affects
vehicle size, weight and cost.
Properties of Silicon and Silicon CarbideProperty Si SiC
Band gap energy (eV) 1.12 3.26
Breakdown electric field (V/cm) 2 x 105 2.2 x 106
Thermal conductivity (W/cmK) 1.5 4.56
Maximum junction temperature (°C) 200 600
Table 1. Properties of SiC and Si
Alternatively, wide-band gap semiconductors such as silicon carbide have much higher operating
temperature (known as the junction temperature), thermal conductivity is two to three times higher than Si,
higher breakdown voltage, and has a capability of switching at much higher frequencies with negligible power loss.
The higher operating temperature of the silicon carbide allows the circuit to be placed close to the location where
the temperatures are high. High thermal conductivity of silicon carbide eliminates the need for big copper blocks
and water jackets. Higher switching speed in the MHz enables the overall power circuitry to become smaller in size.
To address these concerns, TI offers the UCC27531, a gate driver developed to drive these SiC power FETs very
efficiently.
6 Texas Instruments
The value of SMPS using power electronics, particularly with the requirement for higher voltage systems in the
automotive power train system, was discussed. This was followed by a review of the power conditioners involved
to drive various loads in the power train system, followed by the type of topologies being designed into these
systems. The type of semiconductor switches, controller and gate driver requirements were discussed for DC/
DC bi-directional power supplies and DC/AC traction inverters. Finally, the value of implementing wide-band gap
semiconductors such as SiC was discussed for high-temperature applications in the power train.
1. K. K. Afridi, R. D. Tabors, and J. G. Kassakian, “Alternative electrical distribution system architectures for
automobiles,” Proc. of ZEEE Workshop on Power Electronics in Transportation, Dearborn, Oct. 1994, pp. 33-38.
2. S. W. Anderson, R. W. Erickson, and R. A. Martin, “An improved automotive power distribution system using
nonlinear resonant switch converters,” ZEEE Trans. on Power Electronics, vol. 6, no. 1, Jan. 1991, pp. 48-54
3. J. M. Miller, A. Emadi, A. V. Rajarathnam, and M. Ehsani, “Current status and future trends in more electric car
power systems,” in Proc. IEEE Vehicular Technology Conference, Houston, Texas, May 1999.
4. N. Mohan, T. M. Undeland, and W. P. Robbins Power Electronics: Converters, Applications, and Design, 3rd Ed,
John Wiley & Sons, 2003.
5. Download a datasheet for the UCC27531: www.ti.com/product/ucc27531.
6. Check out our latest video on how to overcome temperature challenges in engine blocks: http://focus.ti.com/ general/docs/video/Portal.tsp?entryid=0_tgi6wxfv&lang=en7. For more information about automotive and transportation solutions, visit: http://www.ti.com/lsds/ti/apps/ automotive/end_equipment.page
Conclusion
References
SLYY052
The platform bar is a trademarks of Texas Instruments. All other trademarks are the property of their respective owners.
© 2013 Texas Instruments Incorporated
Important Notice: The products and services of Texas Instruments Incorporated and its subsidiaries described herein are sold subject to TI’s standard terms and conditions of sale. Customers are advised to obtain the most current and complete information about TI products and services before placing orders. TI assumes no liability for applications assistance, customer’s applications or product designs, software performance, or infringement of patents. The publication of information regarding any other company’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
E010208
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and otherchanges to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latestissue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current andcomplete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of salesupplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s termsand conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessaryto support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarilyperformed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products andapplications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provideadequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, orother intellectual property right relating to any combination, machine, or process in which TI components or services are used. Informationpublished by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty orendorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of thethird party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alterationand is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altereddocumentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or servicevoids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirementsconcerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or supportthat may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards whichanticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might causeharm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the useof any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is tohelp enable customers to design and create their own end-product solutions that meet applicable functional safety standards andrequirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the partieshave executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use inmilitary/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI componentswhich have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal andregulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use ofnon-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2013, Texas Instruments Incorporated