Multiple Display Control Protocol - samsung.com · SEC-VD-DSW External Control - 0008 Display S/W,...

SEC-VD-DSW Multiple Display Control - 0008

Multiple Display Control Protocolfor PPM42M5S

PPM42M5HPPM50M5HPPM63M5H Series

Copyright © 2004 2005 Samsung Electronics Co., Ltd

3

1.2. Connection Standards

1) Connection Standards

- Conducts bi-directional communication using RS232.

- Users three signal wires, of TxD (No.2), RxD (No.3), and GND (No.5), among the

RS232 standard wires. (See Fig.1)

- The distance between devices limited to 4m.

- Of the 9 pins of the RS232 port, Nos. 2,3 and 5 are used.

- ID can ge expressed as hexadecimal of given ID, but ID O should be presented only

as 0xFF.

- All communications are cindeucted in the form of hexadecimal numbers, and the

checksum is the sum of all values except for the header. If, as shown in the example

below (11 + FF + 01 +01 =112), the sum is a three-digit interger, discard rhe first

digit and keep the lower two.

ex) Power On & ID=0

Header CommandID

Data Length Data 1 CheckSum0xAA 0x11 1 Power

→

Header Command0xFF

Data Length Data 112

0xAA 0x11 1 1

- If you wish to control all units connected with serial cable regardless of the IDs, set

the ID to "0xFE" and send commands.

Here, each wet functions according to the commands received but does not respond with

ACK.

Table 2-1 RS232 Communication Standards

Bits Rate 9600 bps

Data Bits 8 bits

Parity None

Stop Bits 1 bit

Flow Control None

SEC-VD-DSW External Control - 0008

Display S/W, VD Business Team, Samsung Electronics

4

Fig 2-1 RS-232 pin out DB-9 pin used for Asynchronous Data



5

2. Command

No 명령어 종류 Command Value 값 범위

1 Status Control 0x00 -

2 Time Control 0x01 -

3 On Time Control 0x02 -

4 Off Time Control 0x03 -

5 Video Control 0x04 -

6 RGB Control 0x06 -

7 PIP Status Control 0x07 -

8 Maintenance Control 0x08 -

9 On, Off Timer Status Control 0x0A -

10 Model Number Control 0x10 -

11 Power Control 0x11 0 ~ 1

12 Volume Control 0x12 0 ~ 100

13 Mute Control 0x13 0 ~ 1

14 Input Source Control 0x14 -

15 Image Size Control 0x15 -

16 Contrast Control 0x24 0 ~ 100

17 Brightness Control 0x25 0 ~ 100

18 Sharpness Control 0x26 0 ~ 100

19 Color Control 0x27 0 ~ 100

20 Tint Control 0x28 0 ~ 100

21 Red Gain Control 0x29 0 ~ 100

22 Green Gain Control 0x2A 0 ~ 100

23 Blue Gain Control 0x2B 0 ~ 100

24 Coarse Control 0x2F 0 ~ 1

25 Fine Control 0x30 0 ~ 1

26 H-Position Control 0x31 0 ~ 1

27 V-Position Control 0x32 0 ~ 1

28 Clear Menu Control 0x34 0

29 IR Lock Control 0x36 0 ~ 1

30 RGB Contrast Control 0x37 0 ~ 100



6

31 RGB Brightness Control 0x38 0 ~ 100

32 Zoom Control 0x39 0 ~ 1

33 H-Panning Control 0x3A 0 ~ 1

34 V-Panning Control 0x3B 0 ~ 1

35 PIP On/Off Control 0x3C 0 ~ 1

36 Auto Adjustment Control 0x3D 0

37 Color Tone Control 0x3E 0 ~ 4

38 PIP Source Control 0x40 -

39 Main-PIP Swap Control 0x41 0 ~ 1

40 PIP Size Control 0x42 -

41 PIP Locate Control 0x43 0 ~ 4

42 Sound Select Control 0x47 0 ~ 1

43 Pixel Shift Control 0x4C -

44 Signal Pattern Control 0x4D 0 ~ 1

45 All White Control 0x4E 0 ~ 1

46 Video Wall Control 0x4F -

47 SBP Timer Control 0x5B -

48 Video Wall Mode Control 0x5C 0 ~ 1

Note : "-" indicates when the values to be set are multiple.

See "2.1. Detailed Description of Commands" for details.



7

2.1. Detailed Description of Commands

1) Status Control

● Function

The Computer shows the current settings for the TV/Minitor.

● Get Status

Header CommandID

Data Length CheckSum0xAA 0x00 0

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 Val 2

0xAA 0xFF 9 'A' 0x00 Power Volume

Val 3 Val 4 Val 5 Val 6 Val 7 CheckSumMute Input Aspect N Time NF F Time NF

Power : The Power Code for the TV/Monitor.

Volume : The Volume Value for the TV/Monitor. ( 0 ~ 100 )

Mute : The Mute Code for the TV/Monitor.

Input : The Input Source Code for the TV/Monitor.

Aspect : The Image size Code for the TV/Monitor.

N Time NF : On Time On/Off value for the TV/Monitor.

F Time NF : Off Time On/Off value for the TV/Monitor.

● Nak

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'N' 0x00 ERR

ERR : Error Code that shows the type of the error that occurred.

0 Check Sum Error

1 Others



8

2) Time Control

● Function

The Computer controls the current time for the TV/Monitor.

● Get Time Status

Header CommandID


● Set Time

Header CommandID

Data Length Data 1 Data 2 Data 3 Data 4

0xAA 0x01 6 0 H Time M Time 0

Data 5 Data 6 CheckSum0 0

H Time : The Hour Value for the TV/Monitor ( 0 ~ 23 )

M Time : The Minute Value for the TV/Monitor ( 0 ~ 59 )

● Ack

Header CommandID


0xAA 0xFF 8 'A' 0x01 0 H Time

Val 3 Val 4 Val 5 Val 6 CheckSumM Time 0 0 0

H Time, M Time : Same as above

● Nak

Header CommandID





9

3) On Time Control

● Function

The Computer controls when the TV/Monitor turns on.

● Get On Time Status

Header CommandID


● Set On Time

Header CommandID


0xAA 0x02 6 0 N H Time N M Time N Time VR

Data 5 Data 6 CheckSumN Time NF N Time SC

N H Time : The On Time Hour Value for the TV/Monitor ( 0 ~ 23 )

N M Time : The On Time Minute Value for the TV/Monitor ( 0 ~ 59 )

N Time VR : The On Time Volume Value for the TV/Monitor ( 0 ~ 100 )

N Time NF : The On Time ON/OFF value for the TV/MonitorTV / Monitor

1 On Time ON

0 On Time OFF

N Time SC : The source value for the On Time ON/OFF Control

(See 'Input Source Control')

● Ack

Header CommandID


0xAA 0xFF 8 'A' 0x02 0 N H Time

Val 3 Val 4 Val 5 Val 6 CheckSumN M Time N Time VR N Time NF N Time SC

N H Time, N M Time, N Time VR, N Time NF, N Time SC : 상동

● Nak

Header CommandID





10

4) Off Time Control

● Function

The Computer controls when the TV/Monitor turns off.

● Get Off Time Status

Header CommandID


● Set Off Time

Header CommandID


0xAA 0x03 6 0 F H Time F M Time 0

Data 5 Data 6 CheckSumF Time NF 0

F H Time : The Off Time Hour Value for the TV/Monitor ( 0 ~ 23 )

F M Time : The Off Time Minute Value for the TV/Monitor ( 0 ~ 59 )

F Time NF : The Off Time ON/OFF value for the TV/Monitor

1 Off Time ON

0 Off Time OFF

● Ack

Header CommandID


0xAA 0xFF 8 'A' 0x03 0 F H Time

Val 3 Val 4 Val 5 Val 6 CheckSumF M Time 0 F Time NF 0

F H Time, F M Time, F Time NF : Same as avobe

● Nak

Header CommandID





11

5) Video Control (AV, S-Video, Component Only)

● Function

The Computer shows the screen setting for the TV/Monitor.

● Get Video Status

Header CommandID


● Ack

Header CommandID


0xAA 0xFF 0x0A 'A' 0x04 Contrast Brightness

Val 3 Val 4 Val 5 Val 6 Val 7 Val 8 CheckSumSharpness Color Tint ColorTone 0 0

Contrast, Brightness, Sharpness, Color, Tint, ColorTone : Same as avobe

● Nak

Header CommandID





12

6) RGB Control (PC1, PC2 Only)

● Function

The Computer controls the screen setting for the TV/Monitor.

● Get RGB Status

Header CommandID


● Ack

Header CommandID


0xAA 0xFF 0x0A 'A' 0x06 Contrast Brightness

Val 3 Val 4 Val 5 Val 6 Val 7 Val 8 CheckSum0 0 0 Red Gain Green Gain Blue Gain

Contrast, Brightness, Red, Green, Blue : Same as avobe

● Nak

Header CommandID





13

7) PIP Status Control

● Function

The Computer shows the PIP setting for the TV/Monitor.

● Get PIP Status

Header CommandID


● Ack

Header CommandID


0xAA 0xFF 6 'A' 0x07 P.Size P.Source

Val 3 Val 4 CheckSum0 0

P.Size : The PIP size Value Code of the TV/Monitor.

0x00 PIP Off

0x06 Large

0x08 Small

0x04 Double 1

0x05 Double 2

P.Source : The PIP Source Value Code of the TV/Monitor.

● Nak

Header CommandID





14

8) Maintenance Control

● Function

The Computer shows the Maintenance setting for the TV/Monitor.

● Get Maintenance Status

Header CommandID


● Ack

Header CommandID


0xAA 0xFF 0x12 'A' 0x08 Power P.Size

Val 3 Val 4 Val 5 Val 6 Val 7 Val 8

P.Source Shift H.Dot V.Line S.Time S.Pattern


A.White 0 Timer T.Period T.Time V.Wall

Val 15 Val 16Check Sum

V.WallMode 0


P.Size : The value code for the PIP Size of the TV/Monitor.

P.Source : The value code for the PIP Source of the TV/Monitor.

Shift : The On/Off code for the Pixel Shift of the TV/Monitor.

H.Dot : The value code for the Horizontal Dot of the TV/Monitor. (0~4)

V.Line : The value code for the Vertical Line of the TV/Monitor. (0~4)

S.Time : The value code for the Shift Time of the TV/Monitor. (1~4)

S.Pattern : The On/Off code for the Signal Pattern of the TV/Monitor.

A.White : The On/Off code for the All White of the TV/Monitor.

Timer : The value code for the SBP Timer of the TV/Monitor

T.Period : The value code for the SBP Timer Period of the TV/Monitor. (1~24)

T.Time : The value code for the SBP Timer Time of the TV/Monitor. (1~30)

V.Wall : The value code for the Video Wall of the TV/Monitor.

V.WallMode : The value code for the Video Wall Mode of the TV/Monitor.

● Nak

Header CommandID





15

9) On, Off Timer Status Control

● Function

The Computer shows the On, Off Timer setting for the TV/Monitor.

● Get On, Off Timer Status

Header CommandID

Data Length CheckSum0xAA 0x0A 0

● Ack

Header CommandID


0xAA 0xFF 0x0F 'A' 0x0A Power Input


0 N H Time N M Time N Time VR N Time NF N Time SC

Val 9 Val 10 Val 11 Val 12 Val 13Check Sum

0 F H Time F M Time N Time NF 0


N H Time : The On Time Hour Value for the TV/Monitor. ( 0 ~ 23 )

N M Time : The On Time Minutes Value for the TV/Monitor. ( 0 ~ 59 )

N Time VR : The On Time Volume Value for the TV/Monitor. ( 0 ~ 100 )

N Time NF : The On Time ON/OFF value for the TV/Monitor. ( 0 ~ 1 )

N Time SC : The source value for the On Time On/Off control.

(See 'Input Source Control')

F H Time : The Off Time Hour Value for the TV/Monitor.( 0 ~ 23 )

F M Time : The Off Time Minutes Value for the TV/Monitor. ( 0 ~ 59 )

F Time NF : The Off Time ON/OFF value for the TV/Monitor. ( 0 ~ 1 )

● Nak

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'N' 0x0A ERR




16

10) Model Number Control

● Function

The Computer identifies and displays the TV/Monitor's Model Number.

● Get Model Number Status

Header CommandID


● Ack

Header CommandID


0xAA 0xFF 0x05 'A' 0x10 Species Model

Val 3 CheckSum0

Species : TV / Monitor of panel used for the TV/Monitor.

0x01 PDP

0x02 LCD

0x03 DLP

Model : TV / Monitor's model name.

0x01 PPM50H2

0x02 PPM42S2

0x03 PS-42P2ST

0x04 PS-50P2HT

0x05 SyncMaster 400T

0x06 SyncMaster 403T

0x07 PPM42S3, SPD-42P3SM

0x08 PPM50H3, SPD-50P3HM

0x09 PPM63H3, SPD-63P3HM

0x0A PS-42P3ST

0x0B SyncMaster 323T

0x0C SyncMaster 403T - CT40CS(N)

0x0D PPMxxM5x

● Nak

Header CommandID





17

11) Power Control

● Function

The Computer turns the TV/Monitor ON/OFF.

● Get Power ON/OFF Status

Header CommandID


● Set Power ON/OFF

Header CommandID

Data Length Data 1 CheckSum0xAA 0x11 1 Power


1 Power ON

0 Power OFF

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x11 Power

Power : Same as avobe

● Nak

Header CommandID





18

12) Volume Control

● Function

The Computer changes the Volume level of the TV/Monitor.

● Get Volume Status

Header CommandID


● Set Volume

Header CommandID

Data Length Data 1 CheckSum0xAA 0x12 1 Volume

Volume : The Volume level Value Code of the TV/Monitor ( 0 ~ 100 )

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x12 Volume

Volume : Same as avobe

● Nak

Header CommandID





19

13) Mute Control

● Function

The Computer turns the Mute of the TV/Monitor ON/OFF.

● Get Mute ON/OFF Status

Header CommandID


● Set Mute ON/OFF

Header CommandID

Data Length Data 1 CheckSum0xAA 0x13 1 Mute

Mute : The Mute Code for the TV/Monitor.

1 Mute ON

0 Mute OFF

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x13 Mute

Mute : Same as avobe

● Nak

Header CommandID





20

14) Input Source Control

● Function

The Computer changes the Input Source of the TV/Monitor.

● Get Input Source Status

Header CommandID


● Set Input Source

Header CommandID

Data Length Data 1 CheckSum0xAA 0x14 1 Input

Input : The Input Source Code for the TV / Monitor

0x0C AV

0x04 S-Video

0x08 Component

0x15 PC1

0x16 PC2

0x18 DVI

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x14 Input

Input : Same as avobe

● Nak

Header CommandID





21

15) Image Size Control

● Function

The Computer adjusts the Image Size of the TV/Monitor.

It is not operated when the Video Wall is on.

● Get Image Size Status

Header CommandID


● Set Image Size

Header CommandID

Data Length Data 1 CheckSum0xAA 0x15 1 Aspect

Aspect : The Computer adjusts the Image Size of the TV/Monitor.

PC1, PC2, DVI

0x10 16 : 9

0x18 4 : 3

AV, S-VIdeo, Component

0x01 16 : 9

0x02 Panorama

0x05 Zoom 1

0x06 Zoom 2

0x03 14 : 9

0x0B 4 : 3

Note) The computer adjusts the Panorama settings of the TV/Monitor.

It is operated when the current signal sets to Component(480i and 576i).

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x15 Aspect

Aspect : Same as avobe

● Nak

Header CommandID





22

16) Contrast Control (AV, S-Video, Component Only)

● Function

The Computer adjusts the Contrast of the TV/Monitor.

● Get Contrast Status

Header CommandID


● Set Contrast

Header CommandID

Data Length Data 1 CheckSum0xAA 0x24 1 Contrast

Contrast : The Contrast Value Code for the TV/Monitor ( 0 ~ 100 )

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x24 Contrast

Contrast : Same as avobe

● Nak

Header CommandID





23

17) Brightness Control (AV, S-Video, Component Only)

● Function

The Computer adjusts the Brightness setting of the TV/Monitor.

● Get Brightness Status

Header CommandID


● Set Brightness

Header CommandID

Data Length Data 1 CheckSum0xAA 0x25 1 Brightness

Brightness : The Brightness Value Code for the TV/Monitor ( 0 ~ 100 )

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x25 Brightness

Brightness : Same as avobe

● Nak

Header CommandID





24

18) Sharpness Control (AV, S-Video, Component Only)

● Function

The Computer adjusts the Sharpness of the TV/Monitor.

● Get Sharpness Status

Header CommandID


● Set Sharpness

Header CommandID

Data Length Data 1 CheckSum0xAA 0x26 1 Sharpness

Sharpness : The Sharpness Value Code for the TV/Monitor ( 0 ~ 100 )

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x26 Sharpness

Sharpness : Same as avobe

● Nak

Header CommandID





25

19) Color Control (AV, S-Video, Component Only)

● Function

The Computer adjusts the Color setting of the TV/Monitor.

● Get Color Status

Header CommandID


● Set Color

Header CommandID

Data Length Data 1 CheckSum0xAA 0x27 1 Color

Color : The Color Value Code for the TV/Monitor ( 0 ~ 100 )

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x27 Color

Color : Same as avobe

● Nak

Header CommandID





26

20) Tint Control (AV, S-Video, Component Only)

● Function

The Computer adjusts the Tint of the TV/Monitor when the video format is NTSC.

Note : It dose not work in PAL signal.

● Get Tint Status

Header CommandID


● Set Tint

Header CommandID

Data Length Data 1 CheckSum0xAA 0x28 1 Tint

Tint : The Tint Value Code for the TV/Monitor ( 0 ~ 100 )

R Tint Value

G (100 - Tint) Value

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x28 Tint

Tint : Same as avobe

● Nak

Header CommandID





27

21) Red Gain Control (PC1, PC2 Only)

● Function

The Computer adjusts the Red Gain of the TV/Monitor.

● Get Red Gain Status

Header CommandID


● Set Red Gain

Header CommandID

Data Length Data 1 CheckSum0xAA 0x29 1 Red

Red : The Red Gain level Value Code of the TV/Monitor ( 0 ~ 100 )

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x29 Red

Red : Same as avobe

● Nak

Header CommandID





28

22) Green Gain Control (PC1, PC2 Only)

● Function

The Computer adjusts the Green Gain of the TV/Monitor.

● Get Green Gain Status

Header CommandID

Data Length CheckSum0xAA 0x2A 0

● Set Green Gain

Header CommandID

Data Length Data 1 CheckSum0xAA 0x2A 1 Green

Green : The Green Gain level Value Code of the TV/Monitor ( 0 ~ 100 )

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x2A Green

Green : Same as avobe

● Nak

Header CommandID





29

23) Blue Gain Control (PC1, PC2 Only)

● Function

The Computer adjusts the Blue Gain of the TV/Monitor.

● Get Blue Gain Status

Header CommandID

Data Length CheckSum0xAA 0x2B 0

● Set Blue Gain

Header CommandID

Data Length Data 1 CheckSum0xAA 0x2B 1 Blue

Blue : The Blue Gain level Value Code of the TV/Monitor ( 0 ~ 100 )

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x2B Blue

Blue : Same as avobe

● Nak

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'N' 0x2B ERR




30

24) Coarse Control (PC1, PC2 Only)

● Function

The Computer adjusts the Coarse settings of the TV/Monitor.

It is operated when the current Signal sets to DTV(480p, 576p,720 p, 1080i).

● Get Coarse Status

None

● Set Coarse

Header CommandID

Data Length Data 1 CheckSum0xAA 0x2F 1 Coarse

Coarse : The Frequency Increase/Decrease Code for the TV/Monitor.

1 Increase

0 Decrease

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x2F Coarse

Coarse : Same as avobe

● Nak

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'N' 0x2F ERR




31

25) Fine Control (PC1, PC2 Only)

● Function

The Computer adjusts the Fine settings of the TV/Monitor.

It is operarted when the current Signal sets to DTV(480p, 576p,720 p, 1080i).

● Get Fine Status

None

● Set Fine

Header CommandID

Data Length Data 1 CheckSum0xAA 0x30 1 Fine

Fine : The Phase Increase/Decrease Code for the TV/Monitor.

1 Increase

0 Decrease

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x30 Fine

Fine : Same as avobe

● Nak

Header CommandID





32

26) H-Position Control (PC1, PC2 Only)

● Function

The Computer adjusts the Horizontal Position settings of the TV/Monitor.


● Get H-Position Status

None

● Set H-Position

Header CommandID

Data Length Data 1 CheckSum0xAA 0x31 1 H-Pos

H-Pos : The H-Position Increase/Decrease Code for the TV/Monitor.

1 Shift to the right

0 Shift to the left

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x31 H-Pos

H-Pos : Same as avobe

● Nak

Header CommandID





33

27) V-Position Control (PC1, PC2 Only)

● Function

The Computer adjusts the Vertical Position settings of the TV/Monitor.


● Get V-Position Status

None

● Set V-Position

Header CommandID

Data Length Data 1 CheckSum0xAA 0x32 1 V-Pos

V-Pos : The V-Position Increase/Decrease Code for the TV/Monitor.

1 Shifts downward

0 Shifts upward

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x32 V-Pos

V-Pos : Same as avobe

● Nak

Header CommandID





34

28) Clear Menu Control

● Function

The computer exits the Menu OSD on the TV/Monitor screen.

● Get Clear Menu Status

None

● Set Clear Menu

Header CommandID

Data Length Data 1 CheckSum0xAA 0x34 1 Clear

Clear : 0x00 (Always)

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x34 Clear

● Nak

Header CommandID





35

29) IR Lock Control

● Function

The computer controls Enable/Disable for the IR Lock of the TV/Monitor.

It is operated irrespective of power On/Off.

● Get IR Lock Status

Header CommandID


● Set IR Lock

Header CommandID

Data Length Data 1 CheckSum0xAA 0x36 1 RMC

RMC : The Power Code for the TV/Monitor.

1 Remocon Enable

0 Remocon Disable

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x36 RMC

RMC : Same as avobe

● Nak

Header CommandID





36

30) RGB Contrast Control (PC1, PC2, DVI Only)

● Function

The Computer adjusts the Contrast setting of the TV/Monitor when the Aspect is

RGB.

● Get Contrast Status

Header CommandID


● Set Contrast

Header CommandID

Data Length Data 1 CheckSum0xAA 0x37 1 Contrast

Contrast : The RGB Contrast Value Code for the TV/Monitor ( 0 ~ 100 )

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x37 Contrast

Contrast : Same as avobe

● Nak

Header CommandID





37

31) RGB Brightness Control (PC1, PC2, DVI Only)

● Function

The Computer adjusts the Brightness setting of the TV/Monitor when the Aspect is

RGB.

● Get Brightness Status

Header CommandID


● Set Brightness

Header CommandID

Data Length Data 1 CheckSum0xAA 0x38 1 Brightness

Brightness : The RGB Brightness Value Code for the TV/Monitor ( 0 ~ 100 )

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x38 Brightness


● Nak

Header CommandID





38

32) Zoom Control (PC1, PC2 Only)

● Function

The Computer adjusts the Aspect's Zoom of the TV/Monitor.

● Get Zoom Status

None

● Set Zoom

Header CommandID

Data Length Data 1 CheckSum0xAA 0x39 1 Zoom

Zoom : The Zoom Increase/Decrease Code for the TV/Monitor.

1 Increase

0 Decrease

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x39 Zoom

Zoom : Same as avobe

● Nak

Header CommandID





39

33) H-Panning Control (PC1, PC2 Only)

● Function

The Computer adjusts the Horizontal Panning of the TV/Monitor.

Avalable only with TV/ Monitor in which the Zoom(0x39) is on.

● Get H-Panning Status

None

● Set H-Panning

Header CommandID

Data Length Data 1 CheckSum0xAA 0x3A 1 H-Pan

H-Pan : The H-Panning Increase/Decrease Code for the TV/Monitor.

1 shift to the right

0 shift to the left

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x3A H-Pan

H-Pan : Same as avobe

● Nak

Header CommandID





40

34) V-Panning Control (PC1, PC2 Only)

● Function

The Computer adjusts the Vertical Panning of the TV/Monitor.

Avalable only with TV/ Monitor in which the Zoom(0x39) is on.

● Get V-Panning Status

None

● Set V-Panning

Header CommandID

Data Length Data 1 CheckSum0xAA 0x3B 1 V-Pan

V-Pan : The V-Panning Increase/Decrease Code for the TV/Monitor.

1 shifts downward

0 shifts upnward

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x3B V-Pan

V-Pan : Same as avobe

● Nak

Header CommandID





41

35) PIP On / Off Control

● Function

The Computer turns the PIP function of the TV/Monitor ON/OFF.

It is not operated when the Video Wall is on.

● Get PIP ON/OFF Status

Header CommandID

Data Length CheckSum0xAA 0x3C 0

● Set PIP ON/OFF

Header CommandID

Data Length Data 1 CheckSum0xAA 0x3C 1 PIP

PIP : The PIP On/Off Code for the TV/Monitor.

1 PIP ON

0 PIP OFF

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x3C PIP

PIP : Same as avobe

● Nak

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'N' 0x3C ERR




42

36) Auto Adjustment Control (PC1, PC2 Only)

● Function

The Computer adjusts the RGB screen Setting Automatically.

It is not operated when the current Signal sets to DTV(480p, 576p, 720p, 1080i).

● Get Auto Adjustment Status

None

● Set Auto Adjustment

Header CommandID

Data Length Data 1 CheckSum0xAA 0x3D 1 Auto

Auto : 0x00 (Always)

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x3D Auto

● Nak

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'N' 0x3D ERR




43

37) Color Tone Control (AV, S-Video, Component Only)

● Function

The Computer adjusts the Color Tone setting of the TV/Monitor.

● Get Color Tone Status

Header CommandID

Data Length CheckSum0xAA 0x3E 0

● Set Color Tone

Header CommandID

Data Length Data 1 CheckSum0xAA 0x3E 1 Color Tone

Color Tone : The Color Tone Value Code for the TV/Monitor. ( 0 ~ 4 )

0x00 Cool 2

0x01 Cool 1

0x02 Normal

0x03 Warm 1

0x04 Warm 2

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x3E Color Tone


● Nak

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'N' 0x3E ERR




44

38) PIP Source Control

● Function

The Computer adjusts the PIP Source of the TV/Monitor.

Available only when the PIP function is on.

● Get PIP Source Status

Header CommandID


● Set PIP Source

Header CommandID

Data Length Data 1 CheckSum0xAA 0x40 1 P.Source

P.Source : The Input Source Value Code of the TV/Monitor.

Changing the PIP source may not be available depending on the main source.

See table below.

AV S-Video Component PC1 PC2 DVI

AV X X X O ○ X

S-Video X X X O ○ X

Component X X X O ○ X

PC1 ○ ○ ○ X X ○

PC2 ○ ○ ○ X X ○

DVI X X X O ○ X

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x40 P.Source

P.Source : Same as avobe

● Nak

Header CommandID





45

39) Main-PIP Swap Control

● Function

The Computer swaps the main screen with the PIP screen.


● Get Main-PIP Swap Status

None

● Set Main-PIP Swap

Header CommandID

Data Length Data 1 CheckSum0xAA 0x41 1 Swap

Swap : 0x00 (Always)

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x41 Swap

● Nak

Header CommandID





46

40) PIP Size Control

● Function

The Computer changes the PIP size of the TV/Monitor.

When the PIP is off, it is to be on automatically.

● Get PIP Size Status

Header CommandID


● Set PIP Size

Header CommandID

Data Length Data 1 CheckSum0xAA 0x42 1 P.Size

P.Size : The PIP size Value Code for the TV/Monitor

0x00 PIP Off

0x06 Large

0x08 Small

0x04 Double 1

0x05 Double 2

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x42 P.Size

P.Size : Same as avobe

● Nak

Header CommandID





47

41) PIP Locate Control

● Function

The Computer adjusts the PIP position of the TV/Monitor.


● Get PIP Locate Status

None

● Set PIP Locate

Header CommandID

Data Length Data 1 CheckSum0xAA 0x43 1 P.Locate

P.Locate : The PIP Locate Increase/Decrease Code for the TV/Monitor.

0 PIP Off(Get Only)

1 Upper Left

2 Upper Right

3 Lower Right

4 Lower Left

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x43 P.Locate

P.Locate : Same as avobe

● Nak

Header CommandID





48

42) Sound Select Control

● Function

The Computer adjusts the Sound Setting of the TV/Monotor when the PIP function is

ON.


● Get Sound Select

Header CommandID


● Set Sound Select

Header CommandID

Data Length Data 1 CheckSum0xAA 0x47 1 S.Selct

S.Select : The Sound Select code for the TV/Monitor

1 Main

0 Sub

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x47 S.Select

S.Select : Same as avobe

● Nak

Header CommandID





49

43) Pixel Shift Control

● Function

The Computer adjusts the Pixel Shift function of the TV/Monitor.

● Get Pixel Shift Status

Header CommandID


● Set Pixel Shift

Header CommandID


0xAA 0x4C 0x04 Shift H.Dot V.Line S.Time

CheckSum

Shift : The On/Off code for the Pixel Shift of the TV/Monitor.

Note : When the value of Shift os Off, the value of the H.Dot, V.Lines, S.Time may

not be included in the TV/Monitor.

1 ON

0 OFF

H.Dot : The value code for the Horizontal Dot of the TV/Monitor. (0 ~ 4)

V.Line : The value code for the Vertical Line of the TV/Monitor. (0 ~ 4)

S.Time : The value code for the Shift Time of the TV/Monitor. (1 ~ 4)

● Ack

Header CommandID


0xAA 0xFF 0x06 'A' 0x4C Shift H.Dot

Val 3 Val 4 CheckSumV.Line S.Time

Shift, H.Dot, V.Line, S.Time : Same as avobe

● Nak

Header CommandID





50

44) Signal Pattern Control

● Function

The Computer turns the Signal Pattorn function of the TV/Monitor ON/OFF.

● Get Signal Pattern Status

Header CommandID

Data Length CheckSum0xAA 0x4D 0

● Set Signal Pattern

Header CommandID

Data Length Data 1 CheckSum0xAA 0x4D 1 S.Pattern

S.Pattern : The On/Off code for the Signal pattern of the TV/Monitor.

1 ON

0 OFF

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x4D S.Pattern

S.Pattern : Same as avobe

● Nak

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'N' 0x4D ERR




51

45) All White Control

● Function

The Computer turns the All White function of the TV/Monitor ON/OFF.

● Get All White Status

Header CommandID

Data Length CheckSum0xAA 0x4E 0

● Set All White

Header CommandID

Data Length Data 1 CheckSum0xAA 0x4E 1 A.White

A.White : The On/Off code for the All White of the TV/Monitor.

1 ON

0 OFF

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x4E A.White

A.White : Same as avobe

● Nak

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'N' 0x4E ERR




52

46) Video Wall Control

● Function

The Computer turns the Video Wall function of the TV/Monitor ON/OFF.

● Get Video Wall Status

Header CommandID

Data Length CheckSum0xAA 0x4F 0

● Set Video Wall

Header CommandID

Data Length Data 1 CheckSum0xAA 0x4F 1 V.Wall

V.Wall : The value code for the Video Wall of the TV/Monitor.

Set 2 X 2 3 X 3 4 X 4 1 X 5 5 X 1

OFF 0x00 0x00 0x00 0x00 0x00

No. 1 0x11 0x21 0x31 0x41 0x51

No. 2 0x12 0x22 0x32 0x42 0x52

No. 3 0x13 0x23 0x33 0x43 0x53

No. 4 0x14 0x24 0x34 0x44 0x54

No. 5 0x25 0x35 0x45 0x55

... ... ...

No. 9 0x29 0x39

... ...

No. 16 0x40

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x4F V.Wall

V.Wall : Same as avobe

● Nak

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'N' 0x4F ERR




53

47) SBP Timer Control

● Function

The Computer have the Screen Burn Protection Timer set of the TV/Monitor.

● Get SBP Timer Status

Header CommandID

Data Length CheckSum0xAA 0x5B 0

● Set SBP Timer

Header CommandID

Data Length Data 1 Data 2 Data 3 CheckSum0xAA 0x5B 3 Timer T.Period T.Time

Timer : The value code for the SBP Timer of the TV/Monitor.

0 OFF

1 Signal Pattern

2 All White

T.Period : The value code for the SBP Timer Period of the TV/Monitor. (1~24 Hr.)

T.Time : The value code for the SBP Timer Time of the TV/Monitor. (1~30 min.)

● Ack

Header CommandID


0xAA 0xFF 5 'A' 0x5B Timer T.Period

Val 3 CheckSumT.Time

Timer, T.Period, T.Time : Same as avobe

● Nak

Header CommandID





54

48) Video Wall Mode Control

● Function

The Computer changes the mode of the TV/Monitor when Video Wall function is ON.

Available only when the Video Wall function is on.

● Get Video Wall Mode Status

Header CommandID


● Set Video Wall Mode

Header CommandID

Data Length Data 1 CheckSum0xAA 0x5C 1 WallMode

WallMode : The code for the Video Wall Mode of the TV/Monitor.

1 Natural

0 Full

● Ack

Header CommandID

Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'A' 0x5C WallMode

WallMode : Same as avobe

● Nak

Header CommandID





Multiple Display Control Protocol - samsung.com · SEC-VD-DSW External Control - 0008 Display S/W,...

Documents

Transcript of Multiple Display Control Protocol - samsung.com · SEC-VD-DSW External Control - 0008 Display S/W,...