EFFECTUS GRAPHICUS ORTUS S.A. DE C.V. www.equiposgraficos.com

Salnica 259 Col. Sector Naval. Mxico D.F. 02080 Tel: +52 (55) 5396 6580

Muestrario de refacciones Heidelberg

IMPORTANTE:

Este es el Muestrario de Refacciones Comunes para Heidelberg Si usted desea ver un listado completo con todas las refacciones, consulte el

Catlogo de Refacciones para Heidelberg. Intrucciones

1. Identifique la figura (Drawing #) de la seccin de su inters. 2. Identifique el nmero en la figura (Key #) de la parte que busca . 3. Utilice el nmero en la figura para identificar el nmero de parte (Part #) en la/s

pgina/s siguientes. 4. Ingrese a www.equiposgraficos.com y complete el formulario de cotizacin

incluyendo el nmero de parte y descripcin. 5. Solicite asistencia a cristyg@egomexico.com o al +52(55) 5396 6580

Gracias por su compra

http://www.egomexico.com/images/Productos/PRP/Catalogo_refacciones_Heidelberg.pdfhttp://www.egomexico.com/images/Productos/PRP/Catalogo_refacciones_Heidelberg.pdfhttp://www.equiposgraficos.com/http://128.121.161.225/cotizacion.htmmailto:cristyg@egomexico.com

PART # PART #

21 Solo una muestra de nuestro catalogo www.equiposgraficos.com

Replacement parts for: HEIDELBERG

PUMP FILTER - Quickmaster 46

P-9470 31.20

SILENCER P-9413 65.00

RIBBED V-BELTS

TOK - Drive motor (610mm) P-3780 16.50TOK - Drive shaft (762mm) P-3783 36.50GTO 46 - Drive motor (1168mm) P-3785 57.00GTO 46 - 4 Color Drive Belt P-3733 69.00GTO 46/52 - Drive motor P-3716 41.00GTO 52 - Drive motor (1321mm) P-3788 98.80GTO 52 Z/P, V/P - Drive motor (1016mm) P-3790 89.90GTO 52 Z/P, V/P - Drive motor (1397mm) P-3791 69.50Windmill 10 X 15 - Main drive (2150 mm) P-3703 352.00Windmill 10 X 15 - Main drive P-3793 199.80Windmill 10 X 15 - Main drive (2362 mm) P-3893 154.90 Windmill 13 X 18 - Main drive P-3722 229.90

TIMING BELTS - TOKSTACK-LOAD MASTER FEED P-3810 19.00MASTER FEED TABLE P-1697 7.50

FEED TAPESPEEDMASTER 72 & 102 P-3918 34.60MO, SORK P-3927 19.00

SHEET SEPARATORS

(A) KORD (45) HE-K114 7.00(B) KORD (45 with pad) HE-K420 10.90(C) KORD (90) HE-K117 7.00(D) K-Series HE-KS117 11.90(E) K-Series w/hood HE-KS114 9.90(F) GTO 46 HE-46117 5.60(G) GTO 46 (with hood) HE-46114 6.00(H) GTO 52 HE-52117 9.90(I) GTO 52 (with hood) HE-52118 9.90(J) GTO 52 (45) HE-52114 3.20(K) M/S Series HE-S117 24.90(L) M/S Series HE-S114 29.90(M) M/S Series HE-S106 33.90(N) SB Series (90) HE-SB117 9.50(O) SB Series (45) HE-SB114 9.50(P) WINDMILL HE-WI114 10.00(Q) WINDMILL HE-WI117 9.50(R) Quickmaster 46/46DI HE-46114QM 24.90(S) GTO (Operator side) HE-52106 53.40(T) SM52/74 (Operator side) HE-52106SM 64.90(U) GTO (Non-Operator side) HE-52107 53.40(V) SM52/74 (Non-Operator side) HE-52107SM 64.90(W) M/S/SM102 Brush HE-S0107 29.90

RUBBER HOOD For sheet separators.

HE-46114-R 4.90

SHEET SEPARATOR BARQUICKMASTER 46 & 46DI

HE-46117QM 224.90

PLATE SPRING For Quickmaster

4mm HE-46099QM-4mm 6.406mm HE-46099QM-6mm 11.00

SHEET STEADIER BRUSH - GTO 46 / 52, K-SeriesComplete HE-46403 82.00

Brush only HE-46420 6.00Wing nut P-3399 2.00Shoulder screw P-8176 9.90

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

S

T

U

V

W

SHEET SEPARATOR HOLDER

KOR HE-KR113 34.00

SHEET SEPARATOR HOLDER - L.H. & R.H. UNIVERSAL. WORKS ON BOTH SIDES OF FEEDER.

KORA, KORD, KORS HE-KRD113 28.90

BRUSH WHEELS For feeder section.

K, M, S, SPEEDMASTER (whtie bristle) HE-SR420 21.20K, M, S, SPEEDMASTERfor cardboard stock (black bristle) HE-SR500 24.00

FEED GRIPPER COMPLETE - GTO 46 & 52

COMPLETE HE-46511 899.90(A) Gripper finger HE-46212 12.00(B) Hex head screw P-2088 .60(C) Needle bearing P-3466 19.90(D) Cam roller P-6838 38.90(E) Flat washer P-595 .60(F) E-ring P-2759 .60(G) Stud-for cam roller P-7943 23.00(H) Taper pin P-431 .60(I) Connecting piece P-11923 9.90(J) Torsion spring HE-46212-T 3.00(K) Gripper pad not sold alone -------(L) Spring HE-46212-E 24.90(M) Grooved pin P-3037 .60(N) Torsion Spring (not shown) (see note) -------(O) Backing Plate HE-46212-BP .90

NOTE: Torsion spring N is obsolete. Spring L & grooved pin M are used in place of it.

SPRING For traveling feed gripper.

K-series HE-K0144 6.50

SUCKER FEET

(A) GTO (9/32 ID x 3/4 OD gum rubber - blue) P-5222 .90(A) GTO (9/32 ID x 3/4 OD polyurethane - red) P-7568 1.80(B) GTO (5/16 ID x 11/16 OD for cardboard) P-5244 1.75(C) HEIDELBERG/KLUGE (7/8 O.D.) P-5210 1.60(C) HEIDELBERG (1-1/16 O.D.) P-7556 1.20(D) HEIDELBERG (5/32 I.D. x 1 O.D.) P-5223 .80(D) WINDMILL (5/32 I.D. x 7/8 O.D.) P-7566 .60(D) WINDMILL (1/8 .ID. x 29/32 O.D.) P-5234 .70(E) SOR (1-1/4 O.D.) P-5236 .80(E) MO/SOR (1-3/16 O.D.) P-5240 .80(E) MO/SOR (1-1/2 O.D.) P-5243 1.00(E) Speedmaster 52 (6/16 I.D. x 1-3/16 O.D.) P-7564 .80(F) SORKZ For tissue paper P-5218 7.00(G) TOM/TOK (1-1/4 Long) P-5215 1.20(G) Quickmaster (11/16 Long) P-7558 .80

SPRING GUIDE (TONGUE) For conveyorK- series HE-KR420 8.50

RETAINER SPRING For GTO 52 feeder.HE-S711 2.40

GRIPPER FINGERHE-46212

B

K I J

GD

FEC

L

MO

A B C D E F G

Solo una muestra de nuestro catalogo www.equiposgraficos.com

PART # PART #

22

Replacement parts for: HEIDELBERG

HOLDER ASSEMBLY - GTO 46/52, WINDMILL PLATENSComplete HE-WI434 59.80Replacement roll pin P-2839 .60Replacement thumb screw P-2022 3.90

SHEET STEADIER ASSEMBLY - GTO 46 / 52, K-SeriesComplete HE-K27 81.90(A) Sheet steadier HE-KR090 38.90(B) Holder HE-46049 35.90(C) Thumb screw P-2022 3.90

FRONT GUIDE - For GTO 46/52, K-Series

(A) Guide only HE-K383 39.90(B) Adjusting knob P-2932 24.10(C) Retainer spring HE-K257 5.50(D) Adjusting screw P-2912 19.90

SHEET STEADIER BRUSH - S-SERIESComplete HE-SR467 159.90(A) Hex head screw P-2077 .60(B) Flat washer P-581 .60(C) Nut P-2603 .60(D) Thumb screw P-2924 24.90(E) Bracket only HE-SR485 54.90(F) Spring washer P-654 .80(G) Sheet steadier brush HE-SR475 69.90

FEEDER BRUSH WHEEL - S-Series, Spdmst. 72/102Complete HE-SR403 89.90(A) Spring P-12319 1.40(B) Thumb screw P-2903 8.90(C) Small bracket HE-SR498 22.00(D) Hex head screw P-2043 .60(E) Large bracket HE-SR473 38.90(F)Thumb screw P-2924 24.90(G) Holder HE-SR492 44.90(H) Pin P-4777 7.00(I) Brush wheel HE-SR420 21.20(J) E-Ring P-2753 .60

SHEET SMOOTHERS

KOR (Complete) HE-KR434 134.90KORD/KORA (Complete) HE-KRD434 118.90KORS (Complete) HE-KRS434 123.90(A) Spring plate (smoother) HE-K779 3.00(B) Screw P-2355 .80(C) Bar only (KOR) ** HE-KR483 61.90(C) Bar only (KORD/KORA) ** HE-KRD483 61.90(C) Bar only (KORS) ** HE-KRS483 79.80(D) Block HE-KR359 33.80(E) Thumb screw P-2924 24.90

SHEET SMOOTHER - GTO 46 (Long)

Complete HE-46434 109.80(A) Bar only HE-46483 59.90(B) Thumb screw P-2924 24.90(C) Block only HE-KR359 33.80(D) Screw P-2305 .60(E) Nut P-2600 .60(F) Pan head screw P-2355 .80(G) Plate spring HE-46779 2.50(H) Roll pin P-516 .60

A CB

A

BC

D

AB

CE

DFG

J IH

GF

ED

BA

D

E

CB

A

C

B F

G

D&E

HA

SHEET SMOOTHER - GTO 46 (Short)Complete HE-46352 89.80(A)Bar only (Not Sold Alone) --------(B)Thumb screw P-2924 24.90(C)Block only HE-KR359 33.80(D)Roll pin P-516 .60

Note: ** bars come without holes - you must drill holes to match your existing block.

SHEET SMOOTHER - GTO 52Complete HE-52434 119.90(A) Bar only HE-52483 59.90(B) Thumb screw P-2924 24.90(C) Block only HE-KR359 33.80(D) Pan head screw P-2355 .80(E) Plate spring HE-46779 2.50(F) Roll pin P-516 .60

Note: ** bars come without holes - you must drill holes to match your existing block.

SHEET SMOOTHER PLATE SPRINGS

SORZ, SORDZ, SORSZ HE-S588 19.90

SORKZ, SORMZ HE-S924 10.90

SHEET SMOOTHER - S-SeriesComplete (Operators side) HE-S562 160.00Complete (Drive side) HE-S568 160.00(A) Spring plate HE-S779 3.20(B) Screw P-10207 .60(C) Bar only ** HE-S483 64.90(D) Block HE-S359 38.90(E) Thumb screw P-2923 9.90(F) Spacer piece (oper. side) HE-S541 42.90(F) Spacer piece (drive side) HE-S573 42.90

SHEET BRAKE - GTO 46 / 52, K-SeriesComplete HE-52467 70.00(A) Strap only HE-52500 9.90(B) Block only HE-52473 29.90(C) Thumb screw P-2924 24.90(D) Stop nut P-2610 .60(E) Screw P-8174 10.40

D

ACB

C

B D

F

AE

E

D C

F

AB

AE

B

DC

PART # PART #

23 Solo una muestra de nuestro catalogo www.equiposgraficos.com

Replacement parts for: HEIDELBERG

TRANSFER GRIPPER - MOZ, SPEEDMASTER, SORKHE-MT225 38.90

GTO 46 / 52(A) Transfer and Imp. drum (urethane tip) HE-52245 49.90(A) Transfer and Imp. drum (plain metal tip) HE-52237 33.00(B) Imp.Perfecting drum (urethane tip) HE-M237 135.90

Reversing Drum (upper position) HE-521020-RU 79.90Reversing Drum (lower position) HE-521020-RL 59.90

K-SERIES(C) Transfer and Imp. drum (metalized grit tip)HE-KR225 39.50

M-SERIES(D) Feed drum (urethane tip) HE-72225 38.90(A) Transfer and Imp. drum (urethane tip) HE-52245 49.90(A) Transfer and Imp. drum (plain metal tip) HE-52237 33.00(A) Transfer drumCoating unit (metal tip) HE-52237 33.00(A) Imp. drumCoating unit (urethane tip) HE-52245 49.90(A) Imp. drumCoating unit (plain metal tip) HE-52237 33.00

HE-MO1020 19.90HE-MO1050 6.90

QUICKMASTER 46 / 46DI & TOM / TOK(E) Impression drum (urethane tip) HE-46237QM 30.50

S-SERIES(F) Transfer and Imp. drum (urethane tip) HE-SK237 65.00(F) Transfer and imp. drum (plain metal tip) HE-SK245