MSAG3.1 Commission Guide v3.1 GISB(Control Card)

Confidential and Proprietary Information of ZTE CORPORATION


Integrated Access Gateway

ZXMSG5200 V3.1 Commissioning Guide

Preface

Welcome to use MSG5200 equipment.

If you have used 5200-V3.1 and previous versions, you have had a full knowledge of our

equipment and it may be an easy thing for you to configure this equipment. You need to read

this guide carefully. If you have never used 5200 equipment, this guide provides you a quick

understanding of the equipment.

V 3.1 Made by liuxin 10125036

Mail:[email protected]

Contact:03145111470



contents

Preface ...................................................................................................................................................... 1

commission guide ..................................................................................................................................... 3

1. OverView of MSAG5200 ................................................................................................................ 3

2. Hardware introduce .......................................................................................................................... 3

2.1. Card type and service .................................................................................................. 4

2.2. Hardware connection ................................................................................................... 5

3. Service Commission introduce......................................................................................................... 7

3.1. Entering into Data Configuration Interface ................................................................. 8

3.2. Delete original data ................................................................................................... 10

3.3. configuring Physical Position .................................................................................... 11

3.4. Upgradation the version ............................................................................................ 12

3.5. HSI Service configuration ......................................................................................... 17

3.6. IPTV Service configuration....................................................................................... 20

3.7. VOIP service configuration ....................................................................................... 22

3.8. NMS service configuration ....................................................................................... 25

3.9. 1+1 uplink protection LACP ............................................................................ 26

3.10. 1:1 uplink protection UAPS ............................................................................. 27

3.11. Selfswitch function .................................................................................................... 28

3.12. EPM configuration .................................................................................................... 29

3.13. Second dail configuration .......................................................................................... 35

3.14. DDN service configuration ....................................................................................... 36

3.15. ISDN-BRI service configuration ............................................................................... 39

3.16. ISDN PRI CONFIGURATIONS .............................................................................. 40

3.17. PPPOE+ function ...................................................................................................... 41

3.18. Function switch ......................................................................................................... 41

3.19. STAND BY SS CONFIGURATIONS ...................................................................... 43

3.20. SHDSL configration .................................................................................................. 43



commission guide

1. OverView of MSAG5200

MSAG is the access equipment of SS (soft switch equipment MGC). MSAG connects with

SS via H248 protocol (or MGCP). MSAG is made up of control cardmedia resources sub

card test card and several subscriber cards, converging with a certain amount of

narrowband analog phone access and broadband ADSL access. The phone services are

provided by SS and broadband services are provided by internet.

2. Hardware introduce



2.1. Card type and service

Card name Type Using Shelf/slot---function

GISB Control and switch card All shelves 9/10 slot;

GISE/GISB with

out voip subcard

Control and switch card Slave shelves 9/10 slot;

GISE only support Narrow band

service

GISB support both Narrow band

and Broad band services

VOIP subcard Resource card for

VOIP ,GISB card

accessory

Only install On main shelf GISB

card

ODTI Octal digital interface card Main shelf 8,11,12 slot,

subscriber cable is special,

for ISDN PRI / DDN/E1 service

HDB High-speed digital

subscriber card

Main shelf 1~8,11~13 slot

Slave shelves need special version

for DDN/E1/SHDSL service

STD HDB card accessory Only install On HDB card

ALC Analog line card All shelf 1~8,11-15 slot

for 32 Voip normal user

RALC Reverse Analog line card All shelf 1~8,11-15 slot

for 32 Voip Payphone User

TSLCE Subscriber test card Main shelf 16 slot

for 112 test

GELC 32-port integrated voice

data subscriber card

GISB shelf 1~8,11~15 slot

for 32 Voip/ADSL normal user

GVDL 16-port VDSL subscriber

card

GISB shelf 1~8,11~15 slot

for 16 VDSL normal user

DLCE ISDN digital subscriber

card

all shelves 1~8,11~13 slot

for ISDN BRI service

GEI 1000 Mbps Ethernet

cascade

interface card

Main shelf uplink card backplane

subcard

for 2GE+2FE uplink



SUPI Slave shelf uplink

interface card

Slave shelf uplink card backplane

subcard

Expansion shelf, for cascading,

without uplink function

MBSL Backplane of the

dual-power rear outlet

shelf

Mother board for MSAG

2.2. Hardware connection

1) DIP switch(on backplan) :

MBSL----Master: ON:ON:OFF:OFF(0011)

MBSL----Slave: ON:ON:OFF: ON(0010)

Following is Slave shelf dip switch configurations



2) Hw connection:

Master shelf ----Uplink card: GEI

slave shelf ----Uplink card: SUPI

X7 and X8 provide two 100 Mbps Ethernet electrical interfaces for

broadband service uplink.

X5 and X6 provide two 1000 Mbps Ethernet optial interfaces for

broadband service uplink.

X4 is used to connect broadband/narrowband cascade cables,

which provide 5 4 jack. Leave two rows of pins empty, and

then plug in the first cascade cable. Plug one cascade cable every

three rows. Four cascade cables are supported at most to connect

to four slave shelves



3) Fiber connection:

Fiber need connect with Swith/TXN;

check GISB BACT light change to green Flashing every half second The broadband

service is normal.

Also can using command to check uplink status

4) Subscriber cable connection:

Leave the first pin empty plug 3*8 cable connector then after that connector leave one

another pin plug another 3*8 cable connector, this for 1~16 user

Leave the last pin empty plug 3*8 cable connector then befor that connector leave

one another pin plug another 3*8 cable connector,this for 17~32 user

DSL service checking : GELC card ACT light change to green means DSL link up

VOIP service checking: ALC/RALC card hook light change to green means phone hook

up

Also can using command to check status

3. Service Commission introduce

Topology for commission

X4 is used for cascading. The cascade cables provide 5 4 jack.

Leave the first two rows of pins empty. The third, fourth, fifth, and

sixth rows are used for FE broadband/narrowband uplink.

The ninth, tenth, eleventh, and twelfth rows are used for GE broadband/

narrowband uplink.

X1, X2, and X3 are only used to connect the backplanes



Laptop

Cross cable

Console cable

Laptop

Console cable

Cross cable

Infront of MSAG MSAG MBSL board

GISB card

Preparing test equipment for commission

1) 2 Laptop (wftp;wireshark; Procomm Plus;VLC)

2) 1 ADSL 4 lan port modem;

3) Stubbox &TV;

4) Numbers of cross cables&console cables

5) Usb to s323 convertor for laptop

3.1. Entering into Data Configuration Interface

Console service: provide operationmaintenancedebuggingboot mode

Outband service: provide operation ,maintenance port ;connect GISB ethnet port

Inband service: provide operation,maintenance,service port;connect GEI uplink port

Diagram for configuration interface:



Laptop

Console cable

Cross cable

MSAG MBSL board

GISB card

Network cable

1) Power on the master shelf of the cabinet, and the two GISB are in positions. Make the

GISB in Slot 9 as the active card. All the data configurations below are based on the

situation where the Slot 9 is active. we recommend you set Slot 9 as active.

2) Enter the user name and password in serial port ;serial configure baud rate is 9600

Configure your laptop ip using 144.1.1.0/24 then telnet 144.1.1.1 using outband service

user name/passwordzte/zte

3) Enter into the data configuration interface ;

five mode:

ZXAN #; ZXAN (config)#; ZXAN (config-msag)#; ZXAN (version)#; ZXANconfig-if)#

See as below



Specifications on Data Configuration Interface

Interface Function Transfer

SHELL Debugging output exit

ZXAN # Commands of show types can be

used.

configure terminal transfer to ZXAN (config)#

Version transfer to ZXANversion)#

ZXAN (config)# Hardware and broadband data

configuration interface

ZXAN transfer to ZXAN (config-MSAG)#;

Interface x/x transfer to ZXAN (config-if)#

ZXAN (config-msag)# Narrowband data configuration

interface

exit transfer to ZXAN#;

ZXAN (version)# Version configuration interface exit transfer to ZXAN#

ZXAN (config-if)# Sub interface configuration exit transfer to (config)#

3.2. Delete original data

Numbe

r

Step Function

1 ZXAN #cd cfg Go to cfg folder

/cfg

2 ZXAN #dir Check all the folder

3 ZXAN#del startrun.dat delete broadband data

4 ZXAN #cd / exit cfg folder,go to root folder

5 ZXAN # cd data Go to data folder

/data

6 ZXAN #cd v0100 Go to V0100 folder

/data/v0100



7 ZXAN #del *.zdb delete narrowband data in v0100 folder

8 ZXAN #cd / Exit folder ,Go to root folder

9 ZXAN #cd data

Go to data folder

/data

10 ZXAN #cd v0101

Go to V0101 folder

/data/v0101

11 ZXAN #del *.zdb

delete narrowband data in v0101 folder

12 ZXAN (config) #reboot

Reboot system

Notes: all data running on flash, after reboot will reload save data; never do wr after you delete data

3.3. configuring Physical Position

Numbe

r

Step Function

1 ZXAN (config) #add-rack rackno 1 racktype MSAG Add Rack

2 ZXAN (config) #add-shelf rackno 1 shelfno 1 shelftype

CTL_SHELF

Add Master Shelf

3 ZXAN (config) #add-shelf rackno 1 shelfno 2 shelftype

SLAVE_SHELF connectid 1

ZXAN (config) #add-shelf rackno 1 shelfno 3 shelftype

SLAVE_SHELF connectid 2

Add Slave shelf

HW Connectid start from 1;

Shelf range (2-5);Connectid range

(1-4)

4 ZXAN (config) #add-card rackno 1 shelfno 1 slotno 3 ALC

ZXAN (config) #add-card rackno 1 shelfno 1 slotno 4 GELC

Add user board for each service

card for Master shelf

(ALC/RALC/DLCE/ODTI/HDB/G

ELC/GVDL)

Add user board for each service

card for Master shelf

5 ZXAN (config) #add-card rackno 1 shelfno 2 slotno 9 GISB

ZXAN (config) #add-card rackno 1 shelfno 3 slotno 3 GELC

Add slave shelf Main control card

GISE/GISB

Add slave shelf user board for each

service card

(ALC/RALC/DLCE/ODTI/HDB/G

ELC/GVDL)

6 ZXAN (config) #show card Can check all card



7 ZXAN(config)#del-subcard slotno 9 subcardno 2

default value NO.2 subcard is

CNIC/MAPP,you need delete

this,add voip card to NO.2

8 ZXAN(config)#add-subcard slotno 9 subcardno 2 VOIP default value NO.2 subcard is

CNIC/MAPP,you need delete

this,add voip card to NO.2

9 ZXAN(config)#show subcard Check subcard 2voip online

10 ZXAN#write Save data

Notes: Only after config rack system can start update version;uplink card GEI will be auto add by MSAG

3.4. Upgradation the version

1 Diagram for HSI configuration and troubleshooting

Ethernet cable

Ip add:144.1.1.100

Submask:255.255.255.0

Defult outband ip add:144.1.1.1

Submask:255.255.255.0

2 System FTP configuration

Number Step Function

1 ZXAN#config terminal Shift to config mode

2 ZXAN(config)#show interface mng1 Display outband ip and ftp

configration



3 ZXAN(config)#interface mng1

ZXAN(config-if)#boot-server 144.1.1.100

ZXAN(config-if)#boot-username target

ZXAN(config-if)#boot-password target

Shift to management interface;

Both FTP username & Password

must be same at both MSAG &

FTP software

modify ftp server ip address;

modify ftp server username;

modify ftp server password;

4 ZXAN(config-if)#ex

ZXAN(config)#ex

ZXAN#wri

Quit mng1 interface

Quit config mode

Save config data

3 ftp server config

Run this ftp server software,you can see this windows as below:

Click security menu,choice users/rights



Click

Enter username uni,click OK

Enter password uni,click OK

Enter version file directory like as E:\version



Click Done,then minimum software window.

4 Update progress

Download version file to memery


1 ZXAN#version Shift to config mode

2 ZXAN(version)#download version ics.bt

ZXAN(version)#download version ics.fw

ZXAN(version)#download version ics.mvr

ZXAN(version)#download version voip_normal.fw

Download GISB boot/version

3 ZXAN(version)#download version gise.bt

ZXAN(version)#download version gise.mvr

Download GISE boot/version

4 ZXAN(version)#download version gelca.bt

ZXAN(version)#download version gelca.mvr

Download gelca boot/version

5 ZXAN(version)#download version gdl.bt

ZXAN(version)#download version gvdld.fw

ZXAN(version)#download version gvdld.mvr

Download gvdld boot/version

6 ZXAN(version)#download version dti.bt

ZXAN(version)#download version dti.mvr

Download odti boot/version

7 ZXAN(version)#download version dlce.mvr

ZXAN(version)#download version tslce.mvr

Download dlce/tslceversion

Tslc use GDL.BT as its boot

version

NotesALC/HDB no need version

update boot one-by-one slot for sevice card(except control card)



2 ZXAN(version)#update-boot shelfno 1 slotno 3 local

ZXAN(version)#show update-status shelfno 1

Update boot for shelfno 1 slotno 3

Display update status,you can see

success or same versions





success or same version

4 Same for all the service cards for all the shelves . Update boot is slot by slot .













NotesALC/HDB no need version,this document only give the sample ,all configuration follow actually

situation

update version batch every shelf



2 ZXAN(version)#update-version shelfno 1 local


Update version batch for shelfno 1

Display update status, you can see sucess









NotesAll configuration follow actually situation

update boot for main control card every shelf



2 ZXAN(version)#update boot shelfno 1 slotno 9 local Update version batch for shelfno 1


3 ZXAN(version)#update boot shelfno 2 slotno 9 local Update version batch for shelfno 2


4 ZXAN(version)#update boot shelfno 3slotno 9 local Update version batch for shelfno 3



Update version for slave control card every shelf



2 ZXAN(version)#main-backup version

synchronization shelfno 1

ZXAN(version)#show sync-status shelfno 1

Synchronization shelfno 1

Display syn status





Display syn status





Display syn status


Check version every shelf




1 ZXAN(version)#exit Shift to config mode

2 ZXAN#show card Display Card status

3 ZXAN#show version-running shelfno 1

ZXAN#show version-running shelfno 2

ZXAN#show version-running shelfno 3

Display old version,active version,

This version store in flash

4 ZXAN#show version-saved shelfno 1

ZXAN#show version-saved shelfno 2

ZXAN#show version-saved shelfno 3

Display new version,inactive version

This version store in memory


Reboot shelf start from slave shelf


1 ZXAN#reboot shelfno 4

ZXAN#show card shelfno 4

After reboot ,check all cards status for

shelf 4




shelf 3




shelf 2


ZXAN#show card

Master shelf reboot ,need wait same time

before all shelf running


5 Simple trouble shooting

All Card not get up ,change the slot

Shelf not get up ,check DIP switch & HW cable connection

3.5. HSI Service configuration

1) Diagram for HSI configuration and toubleshooting



Configure the Modem in

Bridge mode

Make a dialer in user

laptop and dial.

Soft Bras

Connect the laptop on

Spare FE Uplink port

Configure HSI VLAN untag

the Spare Uplink

Subscriber cable

TRX Equipment

Bras

2) Preparing for starting configure HSI

equipment preparing

1 Laptopsoftwarewiresharksoftbras

2 4 port ADSL modem

3 Number of Network cables

4 Number of subscriber cables

Data preparing:

1) HSI vlan

2) PPPOE username & password

3) HSI configuration step

1) Create vlan

2) User port untag to this vlanuplink port tag to this vlan

3) Change PVC value same to modemenable PVC 1

4) Change ADSL profile

Numbe

r

Step Function



1 ZXAN (config)#vlan 402

ZXAN(config)#vlan database

ZXAN(vlan)#vlan 101,201,301,3999,401

Create vlan 402 (for create one by one)

Create vlan database (for create multi vlan

together)

2 ZXAN (config) #interface adsl_1/4/1-32

ZXAN (config-if-range) #no shutdown

ZXAN(config-if-range) #switchport default vlan

101 pvc 1

Configure the port transfer sub-interface using

range

Open this interface

Add first PVC 1 untag to Vlan 101,

when type default vlan means pvid same to vid

3 ZXAN (config-if-range) #atm pvc 1 vpi 8 vci 81

ZXAN (config-if-range) # PVC 1 enable

Change the first PVC 1 ; VPI&VCI need same to

modem;

Enable the first PVC

4 ZXAN(config-if-range)#adsl profile def2m.prf

Apply adsl profile for link up rate

ADSL2+ can reach 24 M download speed

ADSL2+ can reach 1 M upload speed

5 ZXAN(config)#adsl profile xyz

Creat and modify new adsl profile;profile name is

xyz

6 ZXAN(config)#interface gei_1/9/3

ZXAN(config-if)#switchport vlan

101,201,301,3999,401 tag

ZXAN(config-if)#no shutdown

Configure the uplink

Tag uplink to vlan 101,201,301,399,401

Enable uplink port

7 ZXAN#show vlan 402

Check the vlan information include tag port &

untag port

8 ZXAN#show adsl port-info adsl_1/3/1

Check dsl service link up rate

9 ZXAN#show dsl interface adsl_1/3/1 pvc 1 Check port pvc status

10 ZXAN#show adsl port-config adsl_1/3/1

Check line profile for this adsl port

11 ZXAN#show runing Check all the configuration

12 ZXAN#write Save the data

Notes: all data configure need check again,show running will be more easy to check all the configuration

If configure 1+1 uplink using sgsmartgroup

4) Simple trouble shooting

1) Using one laptop to dialing ,another laptop connected spare FE port,configure

uplink to untag to HIS vlan first ;then using monitor session to capture the PPPOE

packet

2) Using one laptop to dialing, another laptop using softbras to simulate Bras,to check

this vlan is ok or not



Authentication failure testing method at MSAN.doc

software BRAS setting.doc

3.6. IPTV Service configuration

1 Diagram for IPTV configuration and troubleshooting

Uplink network

modem

televisionSTB

subscribercable

LAN cable

Audio/video cable

Fiber cable

Configure the Modem in Bridge mode

PVC same as MSAG

2 Preparing for starting configure IPTV

IPTV include two partlive channel&VOD

live channel: using multicast packet, protocol using IGMP;

function is see the live channel together

VOD : using unicast packet,protocol ;also using for stubbox authentication PPPOE

protocol

Function is register to Bras and also can see the movie

equipment preparing

1 Laptopsoftwarewiresharksoftbrasvlc

2 4 port ADSL modem

3 Number of Network cables

4 Number of subscriber cables

5 Stubbox & TV

Data preparing:

Live channel

1) Mvlan using 3999

2) Channel group

VOD

1) PPPOE username & password for VODneed provide by PTCL

2) VOD vlan

3 IGMP configuration step

Live channel

1) Create vlan



2) Make the MVlan

3) Enable IGMP

4) Change IGMP mode to proxy

5) Add source port for IGMP

6) Add receive port for IGMP

7) Add group for IGMP

8) Add uplink port tag to MVlan

9) Mvlan translate VOD vlan to Mvlan

VOD vlan

1 Add user port PVC 2 untag to VOD vlan;Add uplink port tag to VOD Vlan

2 Change PVC 2 value same to modem;enable PVC 2

3 Add uplink port tag to MVlan

4 Change ADSL profile

IGMP configuration


1 ZXAN (config)#vlan 3999

ZXAN (config) # igmp mvlan 3999

Create vlan 3999 for MVlan

Create MVLan

2 ZXAN (config) #igmp enable Igmp global enable

3 ZXAN(config) #igmp mvlan 3999 work-mode proxy Igmp work mode snooping/proxy

4 ZXAN (config) #igmp mvlan 3999 group 239.194.0.1 to

239.194.0.170

Set Iptv channel

5 ZXAN(config)#igmp mvlan 3999 source-port gei_1/9/3 Set iptv source port

6 ZXAN (config) #igmp mvlan 3999 receive-port

adsl_1/5/1-32 pvc 2

Set iptv receive port


ZXAN(config-if)#switchport vlan 3999 tag

Add uplink to this 3999 Mvlan & VOD

vlan also

8 ZXAN (config) #interface adsl_1/5/1-32 Enter ADSL port config mode

9 ZXAN (config-if-range) #no shutdown Port enable

10 ZXAN (config-if-range) #switchport mode access Set port mode access/trunk/hybrid

VOD part

11 ZXAN (config-if-range) #switchport default vlan 201 pvc

2

Add vlan to PVC2,PVID is 201

VOD part

12 ZXAN (config-if-range) #atm pvc 2 vpi 0 vci 35 Set pvc 2,VPI/VCI



ZXAN (config-if-range) # pvc 2 enable PVC2 enable

13 ZXAN (config-if-range) #adsl profile def4m.prf Set adsl port profile

14 ZXAN (config-if-range) # mvlan-translate 3999 to untag

pvc 2

Translate municast vlan 3999 to

ports PVID 201



VOD register failed

a) If STB fail to connect the server use PPPOE dialing trough computer and verify

username and password.

b) If PPPOE dialing fail through computer please verify VOD vlan

configuration.Using this document

IPTV troubleshooting.doc

UNICAST AND MULTICAST TESTING.doc

3.7. VOIP service configuration

1) Diagram for IPTV configuration and troubleshooting

Configure Monitor session

for uplink ,untag spare unlink

to capture magaco packet

Subscriber cable

TRX Equipment

Softswitch

2) Preparing data for starting config VOIP

Normally using H248 protocol



equipment preparing

1) Phone

2) Number of Network cables

3) Number of subscriber cables

Data preparing:

1) SS type & IP address

2) VOIP protocol H248 or MGCPprotocol port 2944 for h248

3) TID for narrow band user and RTP resource

4) MSAG VOIP IP address and next hop;NAT protocol

5) VOIP vlan

3) VOIP configuration step

1) VOIP subcard should be ok,first time configure will be take long time 10~15 minuter

2) Create VOIP vlan and bind vlan

3) Set Softswitch(MGC) parameter

4) Create MG bind with MGC

5) Set MSAG voip ipaddress and set MSAG voip next hop

6) Set NAT protocol for MSAG

7) Create VOIP TID on each narrow band cards// HW:A ZTE: USER

8) Create RTP resource

9) Add uplink port tag to VOIP vlan

10) Configure IP on VOIP vlan


1 ZXAN(config)#del-subcard slotno 9 subcardno 2

ZXAN(config)#add-subcard slotno 9 subcardno 2 VOIP

ZXAN(config)#show subcard

Delete default subcard 2

Add voip card to subcard 2

Get VOIP subcard status should be OK

2 ZXAN(config)#vlan 301

ZXAN(config-vlan)#voip-bind

ZXAN(config-vlan)#voip-ctrl

ZXAN(config-vlan)#exit

Create VOIP vlan

Bind VOIP media

Bind VOIP signal

3 ZXAN#msag

ZXAN(config-msag)#mgc add 1 10.20.32.5 port 2944

type 1

Config softswitch(MGC) parameter

Type 1 for zte ss

Type 2 for huawei ss

4 ZXAN(config-msag)#mg add 1 1 port 2944

Create MSAG bind with

Softswitch(MGC)

5 ZXAN(config-msag)#voip interface add ctrl-ip

10.63.86.113 ctrl-mask 255.255.255.0 media-ip

Set MSAG VOIP IPaddress



10.63.86.113 media-mask 255.255.255.0 route-mode 2

ZXAN(config-msag)#voip route add 10.63.86.254

Set MSAG VOIP next hop

6 ZXAN(config-msag)#media-nat add 9 1 9 5 5

10.63.86.113 10000

Add NAT protocol for RTP translater

Nat port start from 10000

7 ZXAN(config-msag)# slc terminationid add rackno 1

shelfno 1 3 USER type 3 begin-no 0 digit-length 4

mgid 1

ZXAN(config-msag)# slc terminationid add rackno 1

shelfno 1 7 A type 2 begin-no 0

ZTE Softswitch TID must using

USER0000~USER00XX..ETC

HW Softswitch TID must use

A0~Axxx

8 ZXAN(config-msag)# rtp terminationid add RTP

begin-seqno 1 240 type 3

ZXAN(config-msag)#rtp terminationid add RTP/

begin-seqno 1 240

Add RTP resources if ZTE SS must

start RTP000~RTP0XX

Add RTP resource if HW ss must start

RTP/0~RTP/xx



ZXAN(config)#interface vlan 301

ZXAN(config-if)#ip address 10.63.86.113

255.255.255.0

ZXAN(config-if)#exit

ZXAN(config)# ip route 10.0.0.0 255.0.0.0

10.63.86.254 (vrrp ip , voip next hope )

Add uplink port to VOIP vlan

Configure this IP on this vlan .

Ping next hope to check your config

Add route to PING SS ,

Now Ping SS ip

ZXAN#show vlan 312

ZXAN#show msag mgc

ZXAN#show msag mg

ZXAN#show msag voip-ipaddr

ZXAN#show msag allnat

ZXAN#show msag rtp terminationid

ZXAN#show msag slc terminationid shelf 1 3

ZXAN#show msag h248-status

verify that up link tagged over VOIP

VLAN.

verify that SS parameter is

configured properly or not

vertify Mg configure properly or

not

check MSAG VOIP address and next

hop

check NAT parameter

check RTP

check TID

check H248 status





1) Using wireshark to capture uplink packet to check H248 packet (Megaco),

monitor session for this spare uplink port

2) Ping SS IP address ZXAN# ping 10.16.98.102

3.8. NMS service configuration

1) Diagram for NMS configuration and troubleshooting

Uplink network

LAN cable-outbandSerial cable-console port

terminal

Fiber cable

2) Preparing data for starting config nms

1) NMS vlan

2) NMS IPaddress for MSAG

3) NMS Next hop


1 ZXAN(config)#interface gei_1/9/4 Enter GE port config mode

2 ZXAN(config-if)#switchport vlan 401 tag Create FE port VID connect uplink port

3 ZXAN(config-if)#exit Quit to global config mode

4 ZXAN(config)#interface vlan 401 Enter vlan config mode

5 ZXAN(config-if)#ip address 10.100.10.10

255.255.255.0

Create L3 ip address

6 ZXAN(config-if)#exit Quit to global config mode

7 ZXAN(config)#ip route 10.0.0.0 255.0.0.0

10.100.10.1

Create ip route information,nexthop and

network

8 ZXAN#ping 10.100.10.1 Ping

Notes:You can ping nexthop ip address



ZXAN#ping 10.100.10.1

sending 5,100-byte ICMP echos to 10.100.10.1,timeout is 2 seconds.

!!!!!

Success rate is 100 percent(5/5),round-trip min/avg/max= 0/8/40 ms.


1) Using spare FE uplink to connect one laptop ,configure this spare port in NMS vlan

Configure Laptop ipaddress same to NMS next hop IP

2) Ping MSAG using laptop

NMS.doc

3.9. 1+1 uplink protection LACP

Using 2 GE uplink to meet load sharing with traffic

LACP configuration step

1 Create Smartgroup

2 2 GE uplink must same using same vlan

3 Add smartgroup in these vlan same configuration with GE uplink


1 ZXAN(config)#interface smartgroup1


ZXAN(config-if)exit

create smartgroup 1

add this smartgroup to this vlan

2 ZXAN(config)#interface fei_1/9/3


ZXAN(config-if)#smartgroup 1 mode active

ZXAN(config)#interface fei_1/9/4


ZXAN(config-if)#smartgroup 1 mode active

Add uplink to this vlan

Smartgroup mode have three

Activepassiveon

LACP using active mode

Trunk using on mode

Our suggestion active mode

3 ZXAN(config)#show lacp internal Check LACP status

Simple trouble shooting

ZXAN(config)#show lacp internal



Smartgroup:1

Flag *--LOOP is TRUE

Actor Agg LACPDUs Port Oper Port RX Mux

Port State Interval Priority Key State Machine Machine

-----------------------------------------------------------------------------

gei_1/9/3 selected 30 32768 0x103 0x3d current distributing

gei_1/9/4 selected 30 32768 0x103 0x3d current distributing

if you see two port are all select, means the one plus one function is OK, you can do the

test!

3.10. 1:1 uplink protection UAPS

AG

Uplink network

gei_1/9/3 gei_1/9/4

gei_2/22 gei_2/22

gei_1/10 gei_1/10

gei_1/11 gei_1/11

VLAN plan:

100 HSI

200 NMS

300 VOIP

IP plan:

NMS 12.12.12.254/24 nexthop 12.12.12.1/24

VOIP 10.10.10.254/24 nexthop 10.10.10.3/24

VRRP ipaddress:10.10.10.3/24

VLAN 300 interface

ipaddress:10.10.10.1/24

VLAN 300 interface

ipaddress:10.10.10.2/24

modem


1 ZXAN#configure termianal

ZXAN(config)#uaps-group 1

Create uplink protection group

2 ZXAN(cfg-uaps-1)#port master-port gei_1/9/4

slave-port gei_1/9/3

add port to protection group

(1/9/4 active, 1/9/3 for

standby)

3 ZXAN(cfg-uaps-1)#next-hop 10.10.10.3 link-type

media

Set up to detect link type

(media or normal), can examine



the next-hop ok or not.

ZXAN(config)#show uaps

Group List :

---------------------------------------

Group List :

---------------------------------------

1

ZXAN(config)#show uaps groupid 1

Revertive control : disable

Next-hop : 10.10.10.3

Link-type : media

Link-detect-retry : 5

Link-detect-interval : 3

Link status : connected or NA

Bfd next_hop : 0.0.0.0

Bfd Link status : connected or NA

Switch-type : common port

Master ports status : block gei_1/9/3 : up

Slave ports status : forwarding gei_1/9/4 : up

3.11. Selfswitch function

Dont need connect Softswitch can make dail

Selfswitch configure step

1) Add-phone number

2) Add-digitmap

3) Self-exchange configuration


1 ZXAN (config-msag) #SLC phone-number modify 3

begin-index 1 num 16 begin-phone-number 88801

ZXAN (config-msag) #show msag slc phone-number

ZXAN (config-msag) #SLC phone-number del

Add selfswitch phone number

Get result

Delete selfswitch phone number

2 ZXAN (config-msag) #digitmap add 1 SELFDM digit-map

888XX servicetype 1

Digitmap must follow the number

Like phone number 8888,so digitmap

need 8xxx;

3 ZXAN (config-msag)#MG capability 1 self-exchange 1 Enable self exchange

ZXAN (config-msag)#mg parameter 1 link-kept-time 10

ZXAN(config-msag)#show msag mg parameter mgid 1

Change H248 linkdown time

Check the result



ZXAN (config-msag) #mgc type modify 2 dm-long 15

ZXAN (config-msag) #mgc type modify 2 dm-start 15

ZXAN (config-msag) #show msag mgc type mgctype 2

Change dial tone time

Check the result

3.12. EPM configuration

Creat SNMP TRAP SERVER first use the following command set to set SNMP TRAP

SERVER

Zxan(config)#snmp-server host 116.71.241.228 trap

version 2c public enable NOTIFICATIONS

server-index 1 udp-port 162

MSAG SERVER IN H-9


version 2c public enable NOTIFICATIONS


SNMP TRAP SERVER IN PTCL NOC


version 2c private enable NOTIFICATIONS


FOR LOCAL CHECK DURING PRE PAT

Show snmp config

ZXAN(config)#fan-epm-console epm

Show fan-epm-console

1. Create EPM unit on nms

2. Choose the NE, click create button



3. you will see EPM in the bottom of the rack map

4. config environment sensor



5,only need config the sensor 1 , after this , you can test if all the sensor works well

6,config the power unit



7,click create button

8. COM No usually be 2 , the power type depend on which type of power the site use, then

create OK



9,then at here you will see the temperature , humidity , AC, DC, battery sensor value

10, you can config the sensors threshold at here



11,for test the temperature sensor , you can config the upper value very low

10. power threshold config , config 52 for battery and DC voltage test



11,here to check all the environment and power alarm

3.13. Second dail configuration

182_191_255_20(config-msag)#rtp mprb-parameter dtmf dtmfrelaymode 1 choose viice

coding,

If you still find issue in dialing phone numbers like 1218, 080080800 , 1217, 131 777 77 then use

the following commond

182_191_255_20(config-msag)#rtp mprb-parameter dtmf dtmfrelaymode 6



0 NOT RELAY.

1 VOICE CODING.

2 Red RFC2833.

4 AAL2/IETF.

6 nRed RFC2833.

3.14. DDN service configuration


E1 analysis tester

E1 cable

transmision

Subscriber cable

V35 cable

2) Topo Logic

O H

D D

T B

I

MODEM SDH

Network



3) equipment preparing

1 SHDSL (X3208D) modem

2 Modem interface :V35

3 Test equipmenterror E1 analysis equipmentACTERNA E1 and Data EDT-135

4 HDB card hardware jumper wire config X12~X15X1223X1312X1412

X1512

5 ODTI card hardware jumper wire config X10-X25:12---75ohm,23---120ohm

4) DDN service configure step

1) Configure HDB work mode

1 port mode i.e 1*n*64k

32x64k

1

32

1 port mode is using maximum of 2mb circuit, if your using 1 port mode, it uses all timeslot

for 1 E1 i.e 32 timeslots, the command for configuring 1 port mode is :

msag(config-msag) ddn port add hdb 5 1 type type_hdb subratetype subratetype_32x64k

2 port mode i.e 2*n*64k

16x64k 16x64k

1 17

32

2 port mode is using maximum two 1mb circuits i.e 1mb circuit for first 16 timeslots (1-16 ts),

and 1mb circuit for other 16 timeslots (17-32 ts),the commands for configuring 2 port mode

is :



3 port mode i.e 1*n*64k+2*m*64k

16x64k 8 x64k 8x64k

1 17 25 32

3 port mode can using maximum one 1mb circuit and two 512 kbs circuit , using 1-17

timeslots for 1mb, 17-25 time slots for 512kbs and 25-32 timeslots for other 512kbs,

commands for configuring 3 mode is :






4 port mode 4*n*64k

8x64k 8x64k 8x64k 8x64k

1 9 17 25 32

4 port mode is using maximum four 512kbs circuits,i.e using first 1-9 timeslots for 512kbs,

other 9-17 timeslots 512kbs, other 17-25 for next 512kbs,similarly 25-32 timeslot for last

512kbs circuit,commands for 4 port mode is:





2) Create DDN port for HDB

3) Create DDN port for ODTI

4) Create DDN connection from HDBODTI


1 ZXAN(config-msag)#ddn hdb portnum modify 3 portnum

4*n*64K

Configure HDB work mode

Notes: it can using 4 ports

First port is 24A/24Csecond port is

26A/26Cthird port is 28A/28C

fourth port is 30A/30C

2 ZXAN(config-msag)# ddn port add HDB shelf 3 4 1 type

type_hdb subratetype subtype_3x64k

Create DDN port for HDB

3 ZXAN(config-msag)#ddn port add ODTI shelf 1 8 1 type

type_odti subratetype subtype_3x64k ts 1

Create DDN port for ODTI

Notestotal 364Konly can bind 1

E1 ,start must from ts 1

4 ZXAN(config-msag)#ddn connection add 1 PortName1 HDB

PortName2 ODTI DDN--HBL

Create DDN connection from

HDBODTI

Notes:using name to bind each other

5 ZXAN(config)#set-e1clktype EST2M Set clock source



6 ZXAN#show msag ddn connection

ZXAN#show msag ddn hdb portnum shelf 3 4

ZXAN#show msag ddn port shelf 1 slot 8

ZXAN#show msag ddn port shelf 3 slot 4

ZXAN#show e1clock

check DDN connect

check work mode

check DDN port(ODTI)

check DDN port(HDB)

check clock source

7 ZXAN(config-msag)#pcm attribution modify 8 1

loop-back 1

ODTI E1 loop


Test way pls check this document

DDN config manul.doc

DDN-test.doc

3.15. ISDN-BRI service configuration


Configure Monitor session

for uplink ,untag spare unlink

to capture magaco packet

Subscriber cable

TRX Equipment

Softswitch

NT1

2) equipment preparing

1 ISDN NT1

2 Connect Phone with DLCE card

ISDN parameter preparing

1) Desport 6100 ;local port 2905



2) Interface ID (IID)

3) TID for ISDN user

3) ISDN service configure step

1) Add AS

2) Add ASP ,

3) Bind AS & ASP,

4) Configure D channel

5) Add TID for ISDN user

6) Add SCTP signal port

Notes:before configure ensure H248 is OK;check licence.dat


1 ZXAN(config-msag)#as add 1

ZXAN(config-msag)#asp add 1 6100 2905 1 10.16.98.102

instream 8 outstream 8

ZXAN(config-msag)#asasp add 1 1

ZXAN(config-msag)#show msag as

ZXAN(config-msag)#show msag asp

Add AS ;

Add ASP set parameter for ASP need

Same to Softswith;

Bind AS&ASP;

Check AS status

Check ASP status

2 ZXAN(config-msag)#isdn dlink span add 7 1 1 100 1

ZXAN(config-msag)#show msag isdn dlink attribute

Add Dlink,IID must same to SS

Check ISDN Dlink status

3 ZXAN(config-msag)#show msag slc terminationid 7

ZXAN(config-msag)#slc terminationid add 7 BRA 1

Check ISDN BRI terminal ID

Add ISDN BRI user terminal ID

4 ZXAN(config-msag)#ctrlport add 1 6610 info 1 Add ctrl port


1) First AS & ASP need active ,check parameter with SS

2) Then capture the signal to check

3.16. ISDN PRI CONFIGURATIONS


1 ZXAN(config-msag)#as add 1

ZXAN(config-msag)#asp add 1 6100 2905 1 10.16.98.102

instream 8 outstream 8

ZXAN(config-msag)#asasp add 1 1

ZXAN(config-msag)#show msag as

ZXAN(config-msag)#show msag asp

Add AS ;

Add ASP set parameter for ASP need

Same to Softswith;

Bind AS&ASP;

Check AS status

Check ASP status

2 ZXAN(config-msag)#isdn dlink span add 8 pcm-no 1 1 17 1 1

ZXAN(config-msag)#show msag isdn dlink attribute

Add Dlink,IID must same to SS

17 is the index for version 3

Check ISDN Dlink status



3 ZXAN(config-msag)#show msag trunk terminationid 8 1

ZXAN(config-msag)#trunk terminationid add 8 1 A

begain-no 4001 type 2

Check ISDN PRI terminal ID

Add ISDN PRI user terminal ID

4 ZXAN(config-msag)#ctrlport add 1 9899 info 1 Add ctrl port

3.17. PPPOE+ function

ZXAN(config)#pppoe-plus enable

ZXAN(config)#interface adsl_2/11/2

ZXAN(config-if)#pppoe-plus enable pvc 1

ZXAN(config)#port-location ?

access-node-identifier Config access-node-identifier info

hostname Config port-location hostname

vlan Config specific vlan

vlan-control Config vlan control

3.18. Function switch

Function switch provides additional features which could adjust CPU to process certain type of

traffic and disable the process for certain type of traffic for exam you enable CPU to process

IGMP service but disable DDN service

This file could be accessed by attaining the LICENSE.DAT placed inside CFG folder

182_191_255_32-ITR_DHKLH_MG#dir

Directory of flash:/

attribute size date time name

1 drwx 16384 JUL-06-2011 12:06:40 img

2 drwx 16384 AUG-22-2011 20:10:40 cfg

3 drwx 16384 AUG-29-2011 07:24:46 data

4 drwx 16384 FEB-18-2010 10:31:54 gponont

5 -rwx 8822 AUG-29-2011 07:29:50 error.log

6 drwx 16384 FEB-18-2010 13:48:32 user

7 -rwx 51645 JUN-10-2011 14:40:38 error.log.bak

64880640 bytes total (43188224 bytes free)

drwx ddirectory

r read

wwrite

Img Version saved in this

directory



xexcute

drwx ddirectory

r read

wwrite

xexcute

Cfg Startrun.dat saved in

this directory

drwx ddirectory

r read

wwrite

xexcute

Data Narrowband data saved

in this directory

drwx ddirectory

r read

wwrite

xexcute

Gponont Gpon ont version saved

182_191_255_32-ITR_DHKLH_MG#cd cfg

182_191_255_32-ITR_DHKLH_MG#dir

Directory of flash:/cfg

attribute size date time name

1 drwx 16384 AUG-22-2011 20:10:40 .

2 drwx 16384 JAN-01-1970 00:00:00 ..

3 -rwx 676 FEB-18-2010 13:48:48 license.dat

4 -rwx 236108 AUG-22-2011 20:10:40 startrun.dat

5 -rwx 4096 JUL-14-2011 01:19:08 nvram.dat

64880640 bytes total (43188224 bytes free)

License.dat There are many functions which defined by

this file, H248,MGCP,DDN,ISDN etc.

Startrun.dat Broadband data file, rack,shelf,card,etc.

Nvram.dat Boot parameter, outband ip, mac,etc.

You can download it by using this command

ZXAN#copy flash: /cfg/license.dat ftp: //144.1.1.100/startrun.dat@root:root

you just have to configure FTP server attributes before you download this data

once you finish download this file open it in NOTEPAD and you will see:

#ZXMSAG V2.0 License File

#Comments must start with a '#' mark

#Supported by WuFeng, [email protected]

#define LM_ITEM_START_H248 ((int) 1) /*whether or not enable H.248 services*/

#define LM_ITEM_START_MGCP ((int) 2) /*whether or not enable MGCP services*/



#define LM_ITEM_START_V5 ((int) 3) /*whether or not enable V5 services*/

#define LM_ITEM_START_ISDN ((int) 4) /*whether or not enable ISDN services*/

#define LM_ITEM_START_E1_MNG ((int) 5) /*e1 management*/

#define LM_ITEM_START_ISDN2B ((int) 6) /*ISDN2B Term */

#define LM_ITEM_START_SIP ((int) 7) /*whether or not enable SIP services*/

1=1

2=1

3=1

4=1

5=1

6=1

7=1

1 is for enabling any feature and 0 is to disable any feature.

Set the parameters as per requirement adjust it if required . before doing this please contact

zte if they allow then do it

LM_ITEM_START_H248 INT 1 1 1:enable 0:disable

LM_ITEM_START_MGCP INT 2 1 1:enable 0:disable

LM_ITEM_START_V5 INT 3 1 1:enable 0:disable

LM_ITEM_START_ISDN INT 4 1 1:enable 0:disable

LM_ITEM_START_E1_MNG INT 5 1 1:enable 0:disable

LM_ITEM_START_ISDN2B INT 6 1 1:enable 0:disable

LM_ITEM_START_SIP INT 7 1 1:enable 0:disable

3.19. STAND BY SS CONFIGURATIONS

Use following commands to set stand by SOFT SWITCH whenever required

ZXAN(CONFIG-MSAG)#mgc add

2 10.20.16.2 port 2944 type 2 (TYPE 2 =hauwie TYPE 1 =ZTE)

ZXAN(CONFIG-MSAG)# mg modify 1 1

mgcid2 2 port 2944

Show msag mg Check

Show msag mgc Check

3.20. SHDSL configration

1). Test Enviroment



MSAGV3.1

SHDSL MODEM

SMARTBITS600B

2). Hareware configration

Main control card GISB slot 9

SHDSL CARD GSDLB slot 15

MODEM TAILET 1608

SMARTBITS SMARTBITS 600B

UPLINK SUBCARD GEI

32 subscriber pin to port

M S BLUE ORANGE GREEN BROWN

WHITE 1 2 3 4

RED 5 6 7 8

BLACK 9 10 11 12

YELLOW 13 14 15 16

WHITEBLUE 17 18 19 20

REDBLUE 21 22 23 24

BLACKBLUE 25 26 27 28

YELLOWBLUE 29 30 31 32

GSDLB support 16 shdsl ports, the subscribe sequence is first 8 ports and last 8 ports

There is a connector box: RJ45 transfer to subscriber

RJ45 TRANSFERBOX SUBSCRIBER

WHITEORANGE BLUE 4TH

ORANGE YELLOW 5TH



WHITEGREEN BLACK 3RD

BLUE RED 6TH

WHITEBLUE GREEN 7TH

GREEN YELLOW 8TH

WHITEBROWN BROWN 1ST

BROWN WHITE 2ND

3). Software Configuration

config rack shelf add rack shelf cards

set data-path-mode msag(config)#interface shdsl_1/15/1-16

msag(if-config)#data-path-mode efm

modem only support

efm mode

create shdsl profile msag(config)#shdsl profile 2wire create 4wire and 8wire

like this

Apply profile to ports msag(config)#interfaceshdsl_1/15/1-4

shdsl profile 2wire

shdsl alarm profile sdefval.prf

we use default alarm

profile

Config uplink and shdsl

ports interface shdsl_1/15/1-4

switchport mode hybrid

switchport default vlan 1000

interface fei_0/9/0

no shutdown

switchprot mode hybrid

negotiation auto

switchport defaut vlan 1000

set modem with 8wire Pls check modem configuration docx

check the synchronize

status

show shdsl port-status shdsl_1/15/1

smartbits Send and receive packet for testing

MSAG(CONFIG)#shdsl profile 2wire

SpanConfWireInterface(1-twoWire,2-fourWire,3-sixWire,4-eightWire):[1]

SpanConfMinLineRate(192..30000kbps):[200]

SpanConfMaxLineRate(200..30000kbps):[6000]

SpanConfPSD(1-symmetric,2-asymmetric):[1]

SpanConfTransmissionMode(0-default,1-custom):[0]

SpanConfRemoteEnabled(1-enable,2-disable)):[1]



SpanConfPowerFeeding(1-noPower,2-powerFeed,3-wettingCurrent):[1]

SpanConfCurrCondTargetMarginDown(0..10dB):[5]

SpanConfWorstCaseTargetMarginDown(-10..10dB):[0]

SpanConfCurrCondTargetMarginUp(0..10dB):[5]

SpanConfWorstCaseTargetMarginUp(-10..10dB):[0]

SpanConfUsedTargetMargins(0-default,1-custom):[0]

SpanConfReferenceClock(1-LocalClk,2-NetworkClk,3-DataOrNetworkClk,4-DataClk):[1]

SpanConfLineProbeEnable(1-disable,2-enable):[1]

































4). test 4wires and 2wires like above procedures;

NOTE

pls make sure the pin to port is correctif it is wrongmaybe linkstatus is okbut service not through

G,SHDSL TAINET MODEM CONFIGRATION.docx

Cable order.xlsx

MSAG3.1 Commission Guide v3.1 GISB(Control Card)

Documents

Transcript of MSAG3.1 Commission Guide v3.1 GISB(Control Card)